IRLR3715ZCTRLPBF [INFINEON]
Power Field-Effect Transistor, N-Channel, Metal-oxide Semiconductor FET,;型号: | IRLR3715ZCTRLPBF |
厂家: | Infineon |
描述: | Power Field-Effect Transistor, N-Channel, Metal-oxide Semiconductor FET, |
文件: | 总12页 (文件大小:293K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PD - 96053
IRLR3715ZCPbF
IRLU3715ZCPbF
HEXFET® Power MOSFET
Applications
l High Frequency Synchronous Buck
Converters for Computer Processor Power
l High Frequency Isolated DC-DC
Converters with Synchronous Rectification
for Telecom and Industrial Use
VDSS RDS(on) max
Qg
7.2nC
11m
20V
l Lead-Free
Benefits
l Ultra-Low Gate Impedance
l Fully Characterized Avalanche Voltage
and Current
D-Pak
I-Pak
IRLR3715ZCPbF IRLU3715ZCPbF
Absolute Maximum Ratings
Parameter
Drain-to-Source Voltage
Max.
20
Units
V
VDS
V
Gate-to-Source Voltage
± 20
49
GS
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current
I
I
I
@ TC = 25°C
A
D
D
35
@ TC = 100°C
200
40
DM
P
P
@TC = 25°C
@TC = 100°C
Maximum Power Dissipation
Maximum Power Dissipation
W
D
D
20
Linear Derating Factor
Operating Junction and
0.27
W/°C
°C
T
-55 to + 175
J
T
Storage Temperature Range
STG
Soldering Temperature, for 10 seconds
300 (1.6mm from case)
Thermal Resistance
Parameter
Typ.
–––
–––
–––
Max.
3.75
50
Units
Rθ
Rθ
Rθ
Junction-to-Case
°C/W
JC
JA
JA
Junction-to-Ambient (PCB Mount)
Junction-to-Ambient
110
Notes through ꢀ are on page 11
www.irf.com
1
02/23/06
IRLR/U3715ZCPbF
Static @ TJ = 25°C (unless otherwise specified)
Parameter
Min. Typ. Max. Units
Conditions
BVDSS
Drain-to-Source Breakdown Voltage
20
–––
–––
V
VGS = 0V, ID = 250µA
∆ΒVDSS/∆TJ
RDS(on)
Breakdown Voltage Temp. Coefficient –––
13
––– mV/°C Reference to 25°C, ID = 1mA
Ω
m
Static Drain-to-Source On-Resistance
–––
–––
1.65
–––
–––
–––
–––
–––
33
8.8
11
VGS = 10V, ID = 15A
12.4 15.5
2.55
––– mV/°C
VGS = 4.5V, ID = 12A
VGS(th)
Gate Threshold Voltage
2.1
-4.8
–––
–––
–––
–––
–––
7.2
2.3
0.90
2.6
1.4
3.5
3.8
7.8
13
V
V
DS = VGS, ID = 250µA
DS = 16V, VGS = 0V
∆VGS(th)/∆TJ
IDSS
Gate Threshold Voltage Coefficient
Drain-to-Source Leakage Current
1.0
150
100
-100
–––
11
µA
V
VDS = 16V, VGS = 0V, TJ = 125°C
IGSS
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Forward Transconductance
Total Gate Charge
nA VGS = 20V
VGS = -20V
gfs
S
VDS = 10V, ID = 12A
Qg
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
Qgs1
Qgs2
Qgd
Qgodr
Qsw
Qoss
td(on)
tr
Pre-Vth Gate-to-Source Charge
Post-Vth Gate-to-Source Charge
Gate-to-Drain Charge
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
VDS = 10V
nC VGS = 4.5V
ID = 12A
Gate Charge Overdrive
See Fig. 16
Switch Charge (Qgs2 + Qgd)
Output Charge
nC VDS = 10V, VGS = 0V
Turn-On Delay Time
Rise Time
VDD = 10V, VGS = 4.5V
ID = 12A
td(off)
tf
Turn-Off Delay Time
Fall Time
10
ns Clamped Inductive Load
4.3
810
270
150
Ciss
Coss
Crss
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
VGS = 0V
pF VDS = 10V
ƒ = 1.0MHz
Avalanche Characteristics
Parameter
Single Pulse Avalanche Energy
Typ.
–––
–––
–––
Max.
Units
mJ
A
EAS
IAR
19
12
Avalanche Current
Repetitive Avalanche Energy
EAR
4.0
mJ
Diode Characteristics
Parameter
Min. Typ. Max. Units
Conditions
49
IS
D
Continuous Source Current
–––
–––
MOSFET symbol
(Body Diode)
A
showing the
G
ISM
Pulsed Source Current
–––
–––
200
integral reverse
S
(Body Diode)
p-n junction diode.
VSD
trr
Diode Forward Voltage
–––
–––
–––
–––
11
1.0
17
V
T = 25°C, I = 12A, V = 0V
J S GS
Reverse Recovery Time
Reverse Recovery Charge
Forward Turn-On Time
ns T = 25°C, I = 12A, VDD = 10V
J F
Qrr
ton
di/dt = 100A/µs
3.5
5.3
nC
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
2
www.irf.com
IRLR/U3715ZCPbF
10000
1000
100
10
1000
100
10
VGS
10V
VGS
10V
TOP
TOP
4.5V
3.7V
3.5V
3.3V
3.0V
2.7V
2.5V
4.5V
3.7V
3.5V
3.3V
3.0V
2.7V
2.5V
BOTTOM
BOTTOM
2.5V
1
1
2.5V
0.1
20µs PULSE WIDTH
Tj = 175°C
20µs PULSE WIDTH
Tj = 25°C
0.01
0.1
0.1
1
10
0.1
1
10
V
, Drain-to-Source Voltage (V)
V
, Drain-to-Source Voltage (V)
DS
DS
Fig 1. Typical Output Characteristics
Fig 2. Typical Output Characteristics
2.0
1.5
1.0
0.5
1000
100
10
I
= 30A
D
V
= 10V
GS
T
= 175°C
J
T = 25°C
J
1
0.1
-60 -40 -20
T , Junction Temperature (°C)
J
0
20 40 60 80 100 120 140 160 180
0
2
4
6
8
10
12
V
, Gate-to-Source Voltage (V)
GS
Fig 3. Typical Transfer Characteristics
Fig 4. Normalized On-Resistance
vs. Temperature
www.irf.com
3
IRLR/U3715ZCPbF
10000
6.0
5.0
4.0
3.0
2.0
1.0
0.0
V
= 0V,
f = 1 MHZ
GS
iss
I
= 12A
D
C
C
C
= C + C , C SHORTED
gs
gd
gd
ds
V
V
= 16V
= 10V
= C
DS
DS
rss
oss
= C + C
ds
gd
1000
100
10
C
iss
C
C
oss
rss
1
10
100
0
2
4
6
8
10
Q
Total Gate Charge (nC)
V
, Drain-to-Source Voltage (V)
G
DS
Fig 6. Typical Gate Charge vs.
Fig 5. Typical Capacitance vs.
Gate-to-Source Voltage
Drain-to-Source Voltage
1000
100
10
1000.00
100.00
10.00
1.00
OPERATION IN THIS AREA
LIMITED BY R
(on)
DS
T
= 175°C
J
100µsec
1msec
T
= 25°C
J
1
10msec
Tc = 25°C
Tj = 175°C
Single Pulse
V
= 0V
GS
0.1
0.10
1
10
, Drain-to-Source Voltage (V)
100
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
, Source-to-Drain Voltage (V)
V
V
DS
SD
Fig 8. Maximum Safe Operating Area
Fig 7. Typical Source-Drain Diode
Forward Voltage
4
www.irf.com
IRLR/U3715ZCPbF
2.5
2.0
1.5
1.0
50
40
30
20
10
0
Limited By Package
I
= 250µA
D
-75 -50 -25
0
25 50 75 100 125 150 175 200
, Temperature ( °C )
25
50
75
100
125
150
175
T
J
T
, Case Temperature (°C)
C
Fig 9. Maximum Drain Current vs.
Fig 10. Threshold Voltage vs. Temperature
Case Temperature
10
D = 0.50
1
R1
R1
R2
R2
R3
R3
R4
R4
Ri (°C/W) τi (sec)
0.20
0.10
0.05
1.1512
2.2284
0.3256
0.0448
0.000082
0.000897
0.053599
0.074119
τ
τ
J τJ
τ
Cτ
1τ1
Ci= τi/Ri
τ
τ
τ
2 τ2
3τ3
4τ4
0.1
0.02
0.01
P
DM
t
1
SINGLE PULSE
( THERMAL RESPONSE )
t
2
Notes:
1. Duty factor D =
2. Peak T
t
/ t
1
2
=
P
x
Z
+ T
J
DM
thJC
C
0.01
1E-006
1E-005
0.0001
0.001
0.01
0.1
t
, Rectangular Pulse Duration (sec)
1
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
IRLR/U3715ZCPbF
15V
80
70
60
50
40
30
20
10
0
I
D
TOP
4.2A
6.9A
DRIVER
L
V
DS
BOTTOM 12A
D.U.T
AS
R
+
G
V
DD
-
I
A
2
VGS
Ω
0.01
t
p
Fig 12a. Unclamped Inductive Test Circuit
V
(BR)DSS
t
p
25
50
75
100
125
150
175
Starting T , Junction Temperature (°C)
J
Fig 12c. Maximum Avalanche Energy
vs. Drain Current
I
LD
AS
VDS
Fig 12b. Unclamped Inductive Waveforms
VDD
D.U.T
Current Regulator
VGS
Same Type as D.U.T.
Pulse Width < 1µs
Duty Factor < 0.1%
50KΩ
.2µF
12V
.3µF
Fig 14a. Switching Time Test Circuit
+
V
DS
D.U.T.
-
VDS
90%
V
GS
3mA
10%
VGS
I
I
D
G
Current Sampling Resistors
td(on)
td(off)
tr
tf
Fig 13. Gate Charge Test Circuit
Fig 14b. Switching Time Waveforms
6
www.irf.com
IRLR/U3715ZCPbF
Driver Gate Drive
P.W.
Period
D.U.T
Period
D =
P.W.
+
*
=10V
V
GS
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
-
D.U.T. I Waveform
SD
+
-
Reverse
Recovery
Current
Body Diode Forward
Current
-
+
di/dt
D.U.T. V Waveform
DS
Diode Recovery
dv/dt
V
DD
VDD
Re-Applied
Voltage
• dv/dt controlled by RG
RG
+
-
Body Diode
Forward Drop
• Driver same type as D.U.T.
• ISD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
Inductor Curent
I
SD
Ripple ≤ 5%
* VGS = 5V for Logic Level Devices
Fig 15. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
Id
Vds
Vgs
Vgs(th)
Qgs1
Qgs2
Qgd
Qgodr
Fig 16. Gate Charge Waveform
www.irf.com
7
IRLR/U3715ZCPbF
Power MOSFET Selection for Non-Isolated DC/DC Converters
Synchronous FET
Control FET
The power loss equation for Q2 is approximated
by;
Special attention has been given to the power losses
in the switching elements of the circuit - Q1 and Q2.
Power losses in the high side switch Q1, also called
the Control FET, are impacted by the Rds(on) of the
MOSFET, but these conduction losses are only about
one half of the total losses.
P = P
+ P + P*
loss
conduction
drive
output
P = Irms 2 × Rds(on)
loss ( )
Power losses in the control switch Q1 are given
by;
+ Q × V × f
(
)
g
g
⎛
⎜
Qoss
⎞
⎠
Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput
+
×V × f + Q × V × f
(
)
in
rr
in
⎝ 2
This can be expanded and approximated by;
*dissipated primarily in Q1.
P
= I 2 × Rds(on )
(
)
loss
rms
For the synchronous MOSFET Q2, Rds(on) is an im-
portant characteristic; however, once again the im-
portance of gate charge must not be overlooked since
it impacts three critical areas. Under light load the
MOSFET must still be turned on and off by the con-
trol IC so the gate drive losses become much more
significant. Secondly, the output charge Qoss and re-
verse recovery charge Qrr both generate losses that
are transfered to Q1 and increase the dissipation in
that device. Thirdly, gate charge will impact the
MOSFETs’ susceptibility to Cdv/dt turn on.
⎛
⎛
Qgd
ig
⎞
Qgs2
ig
⎞
⎟
⎜
⎟
⎜
+ I ×
× V × f + I ×
× V × f
in
in
⎝
⎠
⎝
⎠
+ Q × V × f
(
)
g
g
⎛ Qoss
⎞
⎠
+
×V × f
in
⎝
2
This simplified loss equation includes the terms Qgs2
The drain of Q2 is connected to the switching node
of the converter and therefore sees transitions be-
tween ground and Vin. As Q1 turns on and off there is
a rate of change of drain voltage dV/dt which is ca-
pacitively coupled to the gate of Q2 and can induce
a voltage spike on the gate that is sufficient to turn
the MOSFET on, resulting in shoot-through current .
The ratio of Qgd/Qgs1 must be minimized to reduce the
potential for Cdv/dt turn on.
and Qoss which are new to Power MOSFETdata sheets.
Qgs2 is a sub element of traditional gate-source
charge that is included in all MOSFET data sheets.
The importance of splitting this gate-source charge
into two sub elements, Qgs1 and Qgs2, can be seen from
Fig 16.
Qgs2 indicates the charge that must be supplied by
the gate driver between the time that the threshold
voltage has been reached and the time the drain cur-
rent rises to Idmax at which time the drain voltage be-
gins to change. Minimizing Qgs2 is a critical factor in
reducing switching losses in Q1.
Qoss is the charge that must be supplied to the out-
put capacitance of the MOSFET during every switch-
ing cycle. Figure A shows how Qoss is formed by the
parallel combination of the voltage dependant (non-
linear) capacitances Cds and Cdg when multiplied by
the power supply input buss voltage.
Figure A: Qoss Characteristic
8
www.irf.com
IRLR/U3715ZCPbF
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak (TO-252AA) Part Marking Information
www.irf.com
9
IRLR/U3715ZCPbF
I-Pak (TO-251AA) Package Outline
Dimensions are shown in millimeters (inches)
I-Pak (TO-251AA) Part Marking Information
10
www.irf.com
IRLR/U3715ZCPbF
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRL
TRR
16.3 ( .641 )
15.7 ( .619 )
16.3 ( .641 )
15.7 ( .619 )
12.1 ( .476 )
11.9 ( .469 )
8.1 ( .318 )
7.9 ( .312 )
FEED DIRECTION
FEED DIRECTION
NOTES :
1. CONTROLLING DIMENSION : MILLIMETER.
2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ).
3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm
NOTES :
1. OUTLINE CONFORMS TO EIA-481.
Notes:
Calculated continuous current based on maximum allowable
Repetitive rating; pulse width limited by
max. junction temperature.
junction temperature. Package limitation current is 30A.
Starting TJ = 25°C, L = 0.27mH, RG = 25Ω,
ꢀ When mounted on 1" square PCB (FR-4 or G-10 Material).
For recommended footprint and soldering techniques refer to
application note #AN-994.
I
AS = 12A.
Pulse width ≤ 400µs; duty cycle ≤ 2%.
Data and specifications subject to change without notice.
This product has been designed and qualified for the Consumer market.
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 02/06
www.irf.com
11
Note: For the most current drawings please refer to the IR website at:
http://www.irf.com/package/
相关型号:
IRLR3715ZTRLPBF
Power Field-Effect Transistor, 30A I(D), 20V, 0.011ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-252AA, LEAD FREE, PLASTIC, DPAK-3
INFINEON
IRLR3715ZTRPBF
Power Field-Effect Transistor, 30A I(D), 20V, 0.011ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-252AA, LEAD FREE, PLASTIC, DPAK-3
INFINEON
IRLR3715ZTRR
Power Field-Effect Transistor, 49A I(D), 20V, 0.011ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-252AA, DPAK-3
INFINEON
IRLR3715ZTRRPBF
Power Field-Effect Transistor, 30A I(D), 20V, 0.011ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-252AA, LEAD FREE, PLASTIC, DPAK-3
INFINEON
IRLR3717TR
Power Field-Effect Transistor, 30A I(D), 20V, 0.004ohm, 1-Element, N-Channel, Silicon, Metal-oxide Semiconductor FET, TO-252AA, DPAK-3
INFINEON
©2020 ICPDF网 联系我们和版权申明