SBB503R3SCKC [INFINEON]
HIGH RELIABILITY CLASS K HYBRID RADIATION HARDENED, NON-ISOLATED;型号: | SBB503R3SCKC |
厂家: | Infineon |
描述: | HIGH RELIABILITY CLASS K HYBRID RADIATION HARDENED, NON-ISOLATED |
文件: | 总11页 (文件大小:183K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PD-97563B
SBB SERIES
Single Output
HIGH RELIABILITY CLASS K HYBRID,
RADIATION HARDENED, NON-ISOLATED
POINT OF LOAD (POL) VOLTAGE REGULATOR
Description
The SBB Series point of load (POL) DC to DC voltage
regulators are high reliability hermetically sealed thick
film hybrids designed to provide a single regulated DC
output from a DC voltage source. The output power
rating is 14W to 30W depending on output voltage,
with maximum current rating of 14A. The POLs are class
K qualified per MIL-PRF-38534. These products are
designed to operate continuously on board a space
Features
craft up to the rated power output without power derating
n
n
n
n
Total dose >100K Rads (Si)
for case temperature of 85°C. The POLs are suitable
for harsh radiation environments normally encountered
in the geo-synchronous orbit (GEO), medium earth orbit
(MEO), low earth orbit (LEO), deep space, and for other
challenging radiation design applications.
SEE hardness rated with LET > 82 MeV-cm2 /mg
Operates from 4.5V to 5.5V DC supply
Fixed output voltage: 1V, 1.2V, 1.5V, 1.8V,
2.5V and 3.3V are standards
n
Output power up to 30W or 14A maximum
without de-rating
The SBB POL is a non isolated synchronous buck
regulator. It incorporates IR’s heritage- rich components
and circuit design library for long term reliability
expected of system designs with a mission life of up to
18 years or more. The SBB Series of POLs operate from
a DC input power source with the voltage range of 4.5V
to 5.5V. It converts DC input voltage down to a fixed and
highly stable DC output. The standard voltage outputs
are 1.0V, 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V. The output
is adjustable with the addition of an external resistor.
The output adjustment range is approximately ±10% of
a nominal output voltage. Also included is remote
sensing capability to compensate for voltage drops in
the output lines. This feature, in combination with the
output adjustment capability, enables an output voltage
of a POL to be accurately set as needed.
n
n
n
n
High efficiency to 89%
Remote sense compensation
Fixed 400 KHz operating frequency
Output adjustable to ±10% of nominal
output with an external resistor
Enable function pin for remote on/off control
Input undervoltage and output under
voltage protection
Overload and short circuit protection
Low noise with integrated input
and output filters
No external filter capacitors required
Soft start
Under voltage lockout (UVLO)
Synchronization
Output Status Telemetry(POK)
-55 to +85°C operating case temperature
without output power derating
MIL-PRF-38534 element evaluated components
Custom versions available
Derating per MIL-STD-1547 for space flight
MTBF > 2.8 million hours for space
flight environments
n
n
n
n
n
n
n
n
n
n
With its excellent efficiency performance, SBB POLs
are ideal as the point of load regulators for the
distributed power architecture (DPA) design systems.
Other key benefits include excellent dynamic load
response, precise voltage setting, remote output voltage
sensing and synchronization.
n
n
n
n
n
Standard Microcircuit Drawings (SMDs) Available
www.irf.com
1
11/28/12
SBB SERIES
Single Output
The product’s package footprint is less than three
square inches. The package and lid materials are
cold rolled steel. The low profile package measures
1.9"L x 1.5"W x 0.335"H, excluding mounting tabs
and input/output (I/O) pins. The ceramic sealed I/O
pins protrude the package’s side walls with the
mounting tabs on the corners of the side walls. The
I/O pins are copper Alloy 52. The pins are gold plated
for long term storage. Gold is to be removed prior to
assembly. A complete POL weighs less than 60
grams. Cooling of this device can be accomplished
by bonding the base of the package to a metal plate
or heat sink with a thermally conductive material.
The package’s mechanical outline and I/O pins
functional assignment are included in this data sheet.
Undervoltage Lockout (UVLO): An UVLO circuit
prohibits the POL from operating when the line
voltage is too low to maintain the output voltage.
The POL will not start until the line input voltage
rises to approximately 4.3 volts and will shut down
when the input voltage drops below 3.9 volts.
Output Voltage Adjustment: The output voltage
(Vout) of an SBB can be adjusted to ±10% of a
nominal output voltage. One external resistor with
a power rating of > 0.125 watt is required for this
function.
Following is the formula to determine an approximate
value of the resistor and how it needs to be
connected to the functional pins for a higher and a
lower output voltage with respect to the nominal
output voltage.
The SBB POLs are designed, manufactured, tested,
and qualified at IR’s facility in San Jose, California
which is qualified to ISO9001 and MIL-PRF-38534
by DSCC. Flight hardware is 100% screened and
fully compliant to class K per MIL-PRF-38534.
Abbreviated screening version or engineering model
(EM) of the SBB is available for engineering evaluation.
Please refer to the Device Screening table for details.
To reduce Vout, connect an adjust resistor to
Vadjust pin and Output pin
11280×Vout
⎧
⎫
−10280
⎪
⎪
⎪
⎪
Vnom
Radj =
⎨
⎪
⎬
⎪
2×Vout
Vnom
Circuit Description
2 −
⎪
⎩
⎪
⎭
The SBB Series POLs utilize a non-isolated buck
circuit design topology with synchronous output
rectification to maximize efficiency. The nominal
switching frequency is 400 KHz. An internal EMI filter
minimizes the reflected switching ripple current to
meet most space applications at the system level. A
two-stage output filter reduces the output ripple and
noise to a very low level required by today’s digital
loads. No external filter capacitors are required for
typical design applications.
To increase Vout, connect an adjust resistor to
Vadjust pin and Output Return pin
9280×Vout
⎧
⎫
−10280
⎪
⎪
⎪
⎪
Vnom
Radj =
⎨
⎪
⎬
⎪
2×Vout
Vnom
2 −
⎪
⎩
⎪
⎭
Output current is limited under any load fault
condition. It is designed to behave similar to a
constant current source with the output voltage
dropping below nominal. The SBB POL will resume
normal operation when the load current is reduced
below the current limit point. This protects the POL
from both overload and short circuit conditions.
The current limit threshold exhibits a negative
temperature coefficient to reduce the possibility of
thermal runaway.
Where:
Radjust is the value of the adjust resistor in Ohms(Ω)
Vnom is the nominal output voltage of the SBB
2
www.irf.com
SBB SERIES
Single Output
Remote Sense: Output pins 4 and 5 must be connected
to +Sense pin 6 for proper operation. The +Sense pin
may be connected remotely to the output line at the
load to compensate for a voltage drop in the output line
for precise optimum output regulation. The maximum
voltage compensation in combination with the output
voltage adjustment (if required) is limited to 10% of the
nominal output voltage.To enhance the load regulation
performance Input Return (Pin 2) may be connected
externally to Output Return (Pin 3).
POK:The SBB POL also provides a power ok (POK)
output status signal at Pin 11. A logic high signal is
present when the POL’s output voltage is greater
than 95% of the nominal output voltage. A logic low
signal at Pin 11 indicates the POL’s output voltage
drops below the output voltage threshold of 95%
The SBB Series POLs use a proven conservative
design methodology with careful incorporation of
known radiation performance devices and established
reliability components. All components are fully
derated to MIL-STD-1547. Standard design analyses
include stress, thermal, failure modes and effects
(FMEA), reliability & worst case and are available
upon request.
Enable: An Enable pin is provided to remotely turn
the POL on or off. It can also be used for output
sequenceing for multiple SBB POL regulators. The
nominal threshold relative to the input return (pin 2)
is 2.5V. If 3.9 volts or greater are applied to the
Inhibit pin (pin 3) then the POL will operate normally.
The pin may be left open for normal operation. A
voltage of 0.4V or less will cause the SBB POL to
shut down.
Synchronization: An external synchronization port
is provided to allow the multiple SBB POLs to be
synchronized to an external frequency source to
minimize the noise interference coming from the
switching operation of the POLs. The synchronization
frequency ranges from 360 KHz to 440 KHz and the
synchronization signal port can be driven from 5V
logic.
www.irf.com
3
SBB SERIES
Single Output
Absolute Maximum Ratings
Recommended Operating Conditions
Input voltage range
-0.5Vdc to +7.0Vdc
Input voltage range
4.5Vdc to 5.5Vdc
Output power
Internally limited
300°C for 10 seconds
-55°C to +125°C
-55°C to +125°C
Output power
0 to Max. Rated
Lead temperature
Operating case temperature1
Storage temperature
Operating case temperature
Storage temperature
-55°C to +85°C
-55°C to +125°C
1 Meets derating per MIL-STD-1547
Electrical Performance Characteristics
Conditions
Limits
Nom
5.0
Group A
Subgroup
-55°C ≤ TC ≤ +85°C
VIN = 5.0V DC ± 5%, CL = 0
unless otherwise specified
Parameter
Unit
Min
4.5
Max
5.5
Input Voltage
V
Output Voltage (VOUT
SBB501S
)
1
1
1
1
1
1
1.015
1.218
1.523
1.827
2.538
3.350
0.985
1.182
1.478
1.773
2.463
3.251
1.000
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
IOUT = 100% rated load
IOUT = 100% rated load
1.200
1.500
1.800
2.500
3.300
V
2,3
2,3
2,3
2,3
2,3
2,3
1.030
1.236
1.537
1.855
2.550
3.366
SBB501S
0.970
1.164
1.462
1.755
2.450
3.234
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
Output power (POUT
)
SBB501S
14
16.8
21
25.2
30
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
1,2,3
VIN = 4.5, 5.0 and 5.5V, Note 2
VIN = 4.5, 5.0 and 5.5V, Note 2
W
30
Output current (IOUT
SBB501S
)
0
0
0
0
0
0
14
14
14
14
12
9.1
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
1,2,3
1,2,3
A
Line regulation (VRLINE
)
V
IN = 4.5, 5.0, 5.5 Volts
-0.25
0.25
%
IOUT = 0, 50%, 100% rated
Load regulation (VRLOAD
)
-15
-15
-15
-15
-13
-17
15
15
15
15
17
17
SBB501S
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
VIN = 4.5, 5.0, 5.5 Volts
IOUT = 0, 50%, 100% rated
1,2,3
1,2,3
mV
Switching frequency (FS)
Sync Input (Pin 9) open
360
400
440
KHz
For Notes to Electrical Performance Characteristics Table, refer to page 6
4
www.irf.com
SBB SERIES
Single Output
Electrical Performance Characteristics ( continued )
Conditions
Limits
Nom
Group A
Subgroup
-55°C ≤ TC ≤ +85°C
VIN = 5.0V DC ± 5%, CL = 0
unless otherwise specified
Parameter
Unit
Max
Min
Input current (IIN)
IOUT = 0, Pin 10 open
130
40
SBB501S
200
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
mA
Pin 10 shorted to pin 2
50
Output ripple (VRIP
)
SBB501S
30
30
30
30
25
20
V
IN = 4.5, 5.0, 5.5 Volts
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
1,2,3
IOUT = 100% rated load,
Note 3
mV p-p
Efficiency (EFF
)
SBB501S
67
70
73
76
82
86
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
1,2,3
1,2,3
IOUT = 100% rated load
%
Enable Input (Inhibit Function)
Open circuit voltage
Note 1
V
µA
V
V
- 0.8
V
IN
IN
500
50
Drive current (sink)
Voltage range
-0.5
Synchronization Input
Frequency range
Pulse high level
360
Vin -0.5
-0.5
440
Vin +0.5
+0.5
50
KHz
V
V
nS
%
1,2,3
1,2,3
External clock for Sync Input (Pin 9)
Note 1
Pulse low level
Pulse transition time
Pulse duty cycle
20
80
Current Limit point
SBB501S
14.5
14.5
14.5
14.5
12.5
9.5
21.5
21.5
21.5
21.5
17.9
13.7
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
VOUT = 90% of Nominal
Short Circuit, Overload, Note 5
Half Load to/from Full Load, Note 6
A
Power dissipation, load fault (PD)
SBB501S
11
11
11
11
9.5
8.0
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
1,2,3
4,5,6
W
SBB503R3S
Output response to
Step load changes (VTLD
SBB501S
)
-150
-150
-150
-150
-200
-200
150
150
150
150
200
200
SBB501R2S
SBB501R5S
SBB501R8S
SBB502R5S
SBB503R3S
mV
For Notes to Electrical Performance Characteristics Table, refer to page 6
www.irf.com
5
SBB SERIES
Single Output
Electrical Performance Characteristics ( continued )
Conditions
Limits
Nom
Group A
Subgroup
-55°C ≤ TC ≤ +85°C
VIN = 5.0V DC ± 5%, CL = 0
unless otherwise specified
Parameter
Unit
Min
Max
200
Recovery time,
step load changes (TTLD
Half Load to/from Full Load,
Notes 6,7
µs
4,5,6
)
Output response to
step line changes (VTLN
4.5V to/from 5.5V
IOUT = 100% rated load, Notes 1, 8
)
4,5,6
4,5,6
4,5,6
-100
100
200
mV pk
Recovery time,
step line changes (TTLN
4.5V to/from 5.5V
IOUT = 100% rated load, Notes 1,7,8
)
µs
Turn-on Response
No Load, Full Load,
Note 9
Overshoot (VOS
Turn-on Delay (TDLY
)
100
10
mV
ms
)
0.5
Capacitive Load (CL)
IOUT = 100% rated load
No effect on DC performance
Notes 1, 4
1
1
10000
µF
IOUT = 100% rated load
DC to 50KHz, Note 1
Line Rejection
Device Weight
MTBF
28
dB
g
60
6
Hr
MIL-HDBK-217F2, SF, 40°C
2.8 x10
Electrical Performance Characteristics - Notes
1. Parameter is tested as part of design characterization or after design changes. Thereafter, parameter shall be
guaranteed to the limits specified.
2. Parameter verified during line and load regulation tests.
3. Guaranteed for a D.C. to 20MHz bandwidth. Tested using a 20KHz to 10MHz bandwidth.
4. Capacitive load may be any value from 0 to the maximum limit without compromising dc performance.
A capacitive load in excess of the maximum limit may cause erratic behavior during turn-on.
5. Overload power dissipation is defined as the device power dissipation with the load set such that VOUT = 90% of
nominal.
6. Load step transition time ≤ 1.0 µs/A for 3.3V & 2.5V models and ≤ 0.1 µs/A for 1.0V, 1.2V, 1.5V & 1.8V models.
7. Recovery time is measured from the initiation of the transient to where VOUT has returned to within ±1% of its
steady state value.
8. Line step transition time ≤ 10 µs.
9. Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the
Enable pin (pin 10) to the point where VOUT = 90% of nominal.
Radiation Performance Characteristics
Unit
Test
Conditions
Min
Typ
MIL-PRF-883, Method 1019
Total Ionizing Dose ( Gamma ) Operating bias applied during exposure,
100
Krads (Si)
IN
2 / 3 Rated Load, V = 5.0V
Single Event Effects
Heavy ions (LET)
MeV cm2/mg
SEU, SEL, SEGR, SEB
Operating bias applied during exposure,
Full Rated Load, VIN = 5.5V
Test lab: Cyclotron Institute,
Texas A & M University
82
Notes: International Rectifier currently does not have a DLA Land and Maritime (formerly DSCC) certified
Radiation Hardness Assurance Program.
6
www.irf.com
SBB SERIES
Single Output
Block Diagram
Input
1
2
Input Filter
Input
Return
High-Side
Gate Drive
High-Side
Switch
UVLO
PWM
Output
Filter
Enable
Interface
5
4
Output
Output
10
Enable
Current
Controller
Low-side
Gate drive
Low-Side
Switch
Output
Return
Sync. In
3
8
9
Clock
Generator
Sync.
Interface
Current
Sense
Sync. Out
Power OK
Sense
Voltage
Controller
POK
+Sense
Vadjust
11
6
7
Case 12
Fig 1: Typical Efficiency @-55°C - 1.2V Output (For Part Number SBB501R2S)
Typical Efficiency at -55 Degrees C, 1.2V Output
Vin = 4.5V
SBB501R2S
Vin = 5.0V
Vin = 5.5V
85%
80%
75%
70%
65%
60%
55%
50%
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Output Current, A
www.irf.com
7
SBB SERIES
Single Output
Fig 2: Typical Efficiency @25°C - 1.2V Output (For Part Number SBB501R2S)
Typical Efficiency at 25 Degrees C, 1.2V Output
SBB501R2S
Vin = 4.5V
85%
Vin = 5.0V
Vin = 5.5V
80%
75%
70%
65%
60%
55%
50%
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Output Current, A
Fig 3: Typical Efficiency @+85°C - 1.2V Output (For Part Number SBB501R2S)
Typical Efficiency at +85 Degrees C, 1.2V Output
Vin = 4.5V
SBB501R2S
Vin = 5.0V
Vin = 5.5V
85%
80%
75%
70%
65%
60%
55%
50%
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Output Current, A
8
www.irf.com
SBB SERIES
Single Output
Fig 4: Typical Efficiency @ 25°C - 1.5V Output (For Part Number SBB501R5S)
Typical Efficiency at 25 Degrees C, 1.5V Output
P/N SBB501R5S
Vin = 4.5V
Vin = 5.0V
Vin = 5.5V
85%
80%
75%
70%
65%
60%
55%
50%
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Output Current, A
Fig 5:Typical Efficiency @ 25°C - 3.3V Output (For Part Number SBB503R3S)
Typical Efficiency at 25 Degrees C, 3.3V Output
SBB503R3S
Vin = 4.5V
Vin = 5.0V
Vin = 5.5V
95%
90%
85%
80%
75%
70%
0
1
2
3
4
5
6
7
8
9
10
Output Current, A
www.irf.com
9
SBB SERIES
Single Output
Mechanical Outline
1.900
1.15
0.128 4 places
0.050
Max.
0.375
0.25 Typ
0.25
0.25
Typ.
0.20
1.00
Ref.
5 Eq. Spaces 0.20
Non-cum.
1.50
1.75
2.000
Pin
0.040
0.30
0.55
0.170
2.40
Ref.
0.25
Tolerance: .XX = ±0.01
.XXX = ±0.005
0.335 Max.
Pin Designation
Standard Microcircuit Drawing Equivalence Table
Pin #
Designation
Input
Input Return
Standard Microcircuit
Drawing Number
5962-1120601KXA
5962-1120601KXC
5962-1120602KXA
5962-1120602KXC
5962-1120603KXA
5962-1120603KXC
5962-1120604KXA
5962-1120604KXC
5962-1120605KXA
5962-1120605KXC
5962-1120606KXA
5962-1120606KXC
IR Standard
Part Number
1
2
3
SBB501S/CKA
Output Return
Output
SBB501S/CKC
4
SBB501R2S/CKA
SBB501R2S/CKC
SBB501R5S/CKA
SBB501R5S/CKC
SBB501R8S/CKA
SBB501R8S/CKC
SBB502R5S/CKA
SBB502R5S/CKC
SBB503R3S/CKA
SBB503R3S/CKC
5
Output
6
+Sense
Vadjust
Sync In
Sync Out
Enable
POK
7
8
9
10
11
12
Case
Note: Input and output returns
are internally connected
10
www.irf.com
SBB SERIES
Single Output
Device Screening
Requirement
MIL-STD-883 Method
No Suffix
CK
EM
Temperature Range
Element Evaluation
Non-Destructive Bond Pull
Internal Visual
-55°C to +85°C
Class K
Yes
-55°C to +85°C
Class K
Yes
-55°C to +85°C
MIL-PRF-38534
2023
N/A
N/A
2017
Yes
Yes
Temperature Cycle
Constant Acceleration
PIND
1010
Cond C
Cond C
Cond C
3000 Gs
2001, Y1 Axis
2020
3000 Gs
Cond A
3000 Gs
Cond A
N/A
320 hrs @ 125°C
( 2 x 160 hrs )
-55°C, +25°C,
+85°C
320 hrs @ 125°C
( 2 x 160 hrs )
-55°C, +25°C,
+85°C
48 hrs @ 125°C
Burn-In
1015
Final Electrical
( Group A )
MIL-PRF-38534
& Specification
MIL-PRF-38534
1014
-55°C, +25°C,
+85°C
PDA
2%
2%
N/A
Seal, Fine and Gross
Radiographic
External Visual
Cond A, C
Yes
Cond A, C
Yes
Cond A
N/A
2012
2009
Yes
Yes
Notes:
Best commercial practice.
CK is a DLA Land and Maritime (formerly DSCC) part marking used to designate a Class K compliant hybrid.
The CK marking does not indicate the hybrid is radiation certified.
No Suffix is a radiation rated device but not available as a DLA Land and Maritime qualified SMD per MIL-PRF-38534.
International Rectifier currently does not have a DLA Land and Maritime certified Radiation Hardness Assurance Program.
Part Numbering
SBB 5 01 S /XX X
Model
SBB = 30 watts
Lead Finish for CK only
A = Solder Dipped
C = Gold Plated
Nominal Input Voltage
5 = 5V
Blank for No Suffix and EM
Lead Finish for No Suffix = Gold Plated
Lead Finish for EM is Gold Plated or
Solder Dipped depending on availability
Output Voltage
01 = 1V, 01R2 = 1.2V
01R5 = 1.5V, 01R8 = 1.8V
02R5 = 2.5V, 03R3 = 3.3V
Screening Level
(Please refer to Screening Table)
No Suffix, CK, EM
Output
S = Single
WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 252-7105
IR SAN JOSE: 2520 Junction Avenue, San Jose, California 95134, Tel: (408) 434-5000
Visit us at www.irf.com for sales contact information.
Data and specifications subject to change without notice. 11/2012
www.irf.com
11
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明