TLS835B2EL V [INFINEON]
With an input voltage range of 3 V to 40 V and ver;型号: | TLS835B2EL V |
厂家: | Infineon |
描述: | With an input voltage range of 3 V to 40 V and ver |
文件: | 总25页 (文件大小:822K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Features
•
•
•
•
•
•
•
•
•
•
•
•
Wide input voltage range from 3.0 V to 40 V
Adjustable output voltage between 1.5 V and 6 V
Output voltage precision ≤ ±2%
Output current capability up to 350 mA
Ultra low current consumption, typical 20 µA
Very low dropout voltage, typical 100 mV, at output currents below 100 mA
Stable with ceramic output capacitor of 1 µF
Enable
Overtemperature shutdown
Output current limitation
Wide temperature range
Green Product (RoHS compliant)
Potential applications
•
Automotive or other supply systems that are connected to the battery permanently
•
Automotive supply systems that need to operate in cranking condition
Product validation
Qualified for Automotive Applications. Product Validation according to AEC-Q100/101
Description
The OPTIREG™ Linear TLS835B2ELV is a linear voltage regulator with high performance, very low dropout
linear voltage and very low quiescent current.
With an input voltage range of 3 V to 40 V and very low quiescent current of only 20 µA, this regulator is
perfectly suitable for automotive or other supply systems permanently connected to the battery.
The new loop concept combines fast regulation and very high stability while requiring only one small ceramic
capacitor of 1 µF at the output. At output currents below 100 mA the device has a very low dropout voltage of
only 100 mV (for an output voltage of 5 V) and 120 mV (for an output voltage of 3.3 V). The operating range
starts at an input voltage of only 3 V (extended operating range). This makes the TLS835B2ELV suitable for
automotive systems that need to operate during cranking condition.
The device can be switched on and off by the enable feature.
Data Sheet
Rev. 1.1
2018-09-17
www.infineon.com/OPTIREG-Linear
1
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
The output voltage of the TLS835B2ELV can be adjusted and set between 1.5 V and 6 V by connecting an
external voltage divider.
Internal protection features such as output current limitation and overtemperature shutdown, protect the
device from immediate damage caused by failures such as output shorted to GND, overcurrent or
overtemperature conditions.
External components
An input capacitor CI is recommended to compensate for line influences. The output capacitor CQ is necessary
for the stability of the regulating circuit. The TLS835B2ELV is designed to be stable with low ESR ceramic
capacitors.
Type
Package
Marking
TLS835B2ELV
PG-SSOP-14
835B2V
Data Sheet
2
Rev.1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Table of contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
2.1
2.2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin assignment TLS835B2ELV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin definitions and functions TLS835B2ELV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1
3.2
3.3
4
Block description and electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Voltage regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Typical performance characteristics voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Typical performance characteristics current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Typical performance characteristics enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1
4.2
4.3
4.4
4.5
4.6
5
5.1
5.2
5.2.1
5.2.2
5.2.3
5.3
5.4
5.5
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Selection of external components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Input pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Output pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Resistor divider R1, R2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Thermal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Further application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6
7
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Data Sheet
3
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block diagram
1
Block diagram
I
Q
Current
Limitation
EN
ADJ
Enable
Bandgap
Reference
Temperature
Shutdown
GND
Figure 1
Block diagram TLS835B2ELV
Data Sheet
4
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Pin configuration
2
Pin configuration
2.1
Pin assignment TLS835B2ELV
I
1
2
3
4
5
6
7
14
13
12
11
10
9
Q
n.c.
n.c.
EN
n.c.
ADJ
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
GND
8
Figure 2
Pin configuration TLS835B2ELV
2.2
Pin definitions and functions TLS835B2ELV
Pin
Symbol
Function
Input
1
I
It is recommended to place a small ceramic capacitor to GND, close to the pins,
to compensate for line influences
2
3
4
n. c.
n. c.
EN
Not connected
Leave open or connect to GND
Not connected
Leave open or connect to GND
Enable (integrated pull-down resistor)
Enable the IC with high level input signal
Disable the IC with low level input signal
5
6
n. c.
n. c.
Not connected
Leave open or connect to GND
Not connected
Leave open or connect to GND
7
8
GND
n. c.
Ground
Not connected
Leave open or connect to GND
9
n. c.
n. c.
n. c.
Not connected
Leave open or connect to GND
10
11
Not connected
Leave open or connect to GND
Not connected
Leave open or connect to GND
Data Sheet
5
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Pin configuration
Pin
Symbol
Function
12
ADJ
Output adjustment
Connect an external voltage divider to set the output voltage
13
14
n. c.
Q
Not connected
Leave open or connect to GND
Output voltage
Connect output capacitor CQ to GND close to the pin, respecting the values
specified for its capacitance and ESR in “Functional range” on Page 8
Pad
–
Exposed pad
Connect to heatsink area;
Connect to GND
Data Sheet
6
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
General product characteristics
3
General product characteristics
3.1
Absolute maximum ratings
Table 1
Absolute maximum ratings1)
Tj = -40°C to 150°C; all voltages with respect to ground (unless otherwise specified)
Parameter
Symbol
Values
Unit Note or
Test Condition
Number
Min. Typ. Max.
Input I, enable EN
Voltage
VI, VEN
VQ
-0.3
-0.3
-0.3
–
–
–
45
7
V
V
V
–
P_4.1.1
P_4.1.2
P_4.1.3
Output Q
Voltage
–
–
Adjust ADJ
voltage
VADJ
7
Temperatures
Junction temperature
Storage temperature
ESD absorption
ESD susceptibility to GND
ESD susceptibility to GND
Tj
-40
-55
–
–
150
150
°C
°C
–
–
P_4.1.5
P_4.1.6
Tstg
VESD
VESD
-2
–
–
2
kV
V
2) HBM
3) CDM at all pins P_4.1.8
P_4.1.7
-750
750
1) Not subject to production test, specified by design.
2) ESD susceptibility, HBM according to ANSI/ESDA/JEDEC JS001 (1.5 kΩ, 100 pF)
3) ESD susceptibility, Charged Device Model “CDM” according JEDEC JESD22-C101
Notes
1. Exceeding the absolute max ratings may cause permanent damage to the device and affects the device’s
reliability.
2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as operation outside the normal operating range. Protection
functions are not designed for continuous repetitive operation.
Data Sheet
7
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
General product characteristics
3.2
Functional range
Table 2
Functional range
Tj = -40°C to 150°C; all voltages with respect to ground (unless otherwise specified)
Parameter
Symbol
Values
Unit Note or
Test Condition
Number
Min.
Typ.
Max.
40
1)
Input voltage range
VI
VQ,nom + Vdr
–
–
–
–
V
–
–
P_4.2.1
P_4.2.2
P_4.2.3
P_4.2.4
2)
Extended input voltage range VI,ext
3.0
0
40
V
Enable voltage range
VEN
CQ
40
V
–
3)4)
Capacitance of output
capacitor for stability
1
–
µF
–
3)
Equivalent series resistance of ESR(CQ)
output capacitor
–
–
–
40
Ω
–
P_4.2.5
P_4.2.6
Junction temperature
Tj
-40
150
°C
–
1) Output current is limited internally and depends on the input voltage, see electrical characteristics for more details.
2) If VI,ext,min ≤ VI ≤ VQ,nom + Vdr, then VQ = VI - Vdr. If VI < VI,ext,min, then VQ can drop to 0 V.
3) Not subject to production test, specified by design.
4) The minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30%
Note:
Within the functional or operating range, the IC operates as described in the circuit description. The
electrical characteristics are specified within the conditions given in the electrical characteristics
table.
Data Sheet
8
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
General product characteristics
3.3
Thermal resistance
Note:
This thermal data was generated in accordance with JEDEC JESD51 standards. For more
information, go to www.jedec.org.
Table 3
Thermal resistance of TLS835B2ELV in PG-SSOP-14 package
Parameter
Symbol
Values
Min. Typ.
Unit Note or
Test Condition
Number
Max.
1)
Junction to case
RthJC
RthJA
RthJA
–
–
–
10
–
–
–
K/W
K/W
K/W
–
P_4.3.1
P_4.3.2
P_4.3.3
Junction to ambient
Junction to ambient
41
1)2) 2s2p board
125
1)3) 1s0p board,
footprint only
Junction to ambient
Junction to ambient
RthJA
–
–
59
51
–
–
K/W
K/W
1)3) 1s0p board,
300 mm2 heatsink
area on PCB
1)3) 1s0p board,
600 mm2 heatsink
area on PCB
P_4.3.4
P_4.3.5
RthJA
1) Not subject to production test, specified by design
2) Specified RthJA value is according to Jedec JESD51-2,-5,-7 at natural convection on FR4 2s2p board. The product
(chip + package) was simulated on a 76.2 × 114.3 × 1.5 mm³ board with 2 inner copper layers (2 × 70 µm Cu, 2 × 35 µm
Cu). Where applicable a thermal via array under the exposed pad contacted the first inner copper layer.
3) Specified RthJA value is according to JEDEC JESD 51-3 at natural convection on FR4 1s0p board. The product
(chip + package) was simulated on a 76.2 × 114.3 × 1.5 mm3 board with 1 copper layer (1 × 70 µm Cu).
Data Sheet
9
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
4
Block description and electrical characteristics
4.1
Voltage regulation
The output voltage VQ is divided by a resistor network. This fractional voltage is compared to an internal
voltage reference and the pass transistor is driven accordingly.
The control loop stability depends on the following factors:
•
•
•
•
output capacitor CQ
load current
chip temperature
internal circuit design
Output capacitor
To ensure stable operation, the capacitance of the output capacitor and its equivalent series resistor (ESR)
requirements as specified in “Functional range” on Page 8 must be maintained. The output capacitor must
be sized according to the requirements of the application to be able to buffer load steps.
Input capacitors, reverse polarity protection diode
An input capacitor CI is recommended to compensate for line influences.
In order to block influences such as pulses and high frequency distortion at the input, an additional reverse
polarity protection diode and a combination of several capacitors for filtering should be used. Connect the
capacitors close to the component’s terminals.
Smooth ramp-up
In order to prevent overshoots during startup, a smooth ramp-up function is implemented. This ensures
almost no output voltage overshoots during startup, mostly independent from load and output capacitance.
Output current limitation
If the load current exceeds the specified limit, due to a short-circuit for example, then the output current is
limited and the output voltage decreases.
Overtemperature shutdown
The overtemperature shutdown circuit prevents the IC from immediate destruction in case of a fault condition
(for example a permanent short-circuit at the output) by switching off the power stage. After the IC has cooled
down, the regulator restarts. This leads to an oscillatory behavior of the output voltage until the fault is
removed. However, any junction temperature above 150°C is outside the maximum ratings and therefore
significantly reduces the lifetime of the IC.
Data Sheet
10
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
Regulated
Output Voltage
Supply
IQ
II
I
Q
Current
Limitation
R1
EN
CQ
ADJ
Enable
CI1
CI2
RLOAD
VI
VQ
Bandgap
Reference
Temperature
Shutdown
ESR
R2
GND
Figure 3
Voltage regulation
V
VI
Vdr
VQ,nom
VQ
VI,ext,min
t
Figure 4
Output voltage vs. input voltage
Data Sheet
11
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
Table 4
Electrical characteristics voltage regulator
Tj = -40°C to 150°C, VI = 13.5 V, all voltages with respect to ground (unless otherwise specified).
Typical values are given at Tj = 25 °C, VI = 13.5 V.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Output voltage accuracy1) ΔVQ
Output voltage accuracy1) ΔVQ
-2
–
2
%
%
0.05 mA ≤ IQ ≤ 350 mA
3 V ≤ VI ≤ 28 V,
VI ≥ VQ,nom + Vdr,
R2 ≤ 250 kΩ
P_5.1.33
-2
–
2
0.05 mA ≤ IQ ≤ 175 mA
3 V ≤ VI ≤ 40 V,
P_5.1.34
VI ≥ VQ,nom + Vdr,
R2 ≤ 250 kΩ
Reference voltage
Vref
1.47
1.5
–
1.53
6
V
V
–
–
P_5.1.36
P_5.1.37
Output voltage adjustable VQ,Range 1.5
range
Dropout voltage
Vdr = VI - VQ
Vdr
–
–
–
100
250
65
200
500
–
mV
mV
dB
2) IQ = 100 mA, VQ,nom = 6 V P_5.1.43
2) IQ = 250 mA, VQ,nom = 6 V P_5.1.41
Dropout voltage
Vdr = VI - VQ
Vdr
Power supply ripple
rejection3)
PSRR
VQ = 1.5 V,
ripple = 100 Hz,
ripple = 0.5 Vp-p
IQ = 10 mA
P_5.1.44
f
V
,
Output current limitation
IQ,max
351
500
-5
780
–
mA
mV
0 V < VQ < VQ,nom - 0.1 V
P_5.1.47
P_5.1.52
Load regulation
steady-state
ΔVQ,load -15
IQ = 0.05 mA to 350 mA
VI = 7 V
Line regulation
steady-state
ΔVQ,line
–
1
10
200
–
mV
°C
K
VI = 8 V to 32 V
IQ = 5 mA
3)Tj increasing
P_5.1.53
P_5.1.55
P_5.1.56
Overtemperatureshutdown Tj,sd
threshold
151
–
175
15
Overtemperatureshutdown Tj,sdh
3)Tj decreasing
threshold hysteresis
1) Referring to the device tolerance only, the tolerance of the resistor divider can cause additional deviation. Parameter
is tested with the ADJ pin directly connected to the output pin Q.
2) Measured when the output voltage VQ has dropped by 100 mV while input voltage was gradually decreased.
3) Not subject to production test, specified by design
Data Sheet
12
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
4.2
Typical performance characteristics voltage regulator
Output voltage VQ versus
junction temperature Tj
Output voltage VQ versus
junction temperature Tj
1.6
1.58
1.56
1.54
1.52
1.5
6.2
6.15
6.1
6.05
6
1.48
1.46
1.44
1.42
1.4
VI = 13.5 V
Q = 100 mA
Q,nom = 1.5 V
I
V
VI = 13.5 V
Q = 100 mA
Q,nom = 6 V
I
5.95
5.9
V
−40
0
50
100
150
−40
0
50
100
150
Tj [°C]
Tj [°C]
Output voltage VQ versus
input voltage VI
Output voltage VQ versus
input voltage VI
3
7
Tj = −40 °C
Tj = −40 °C
Tj = 25 °C
Tj = 25 °C
6
2.5
Tj = 150 °C
Tj = 150 °C
5
4
3
2
2
1.5
1
IQ = 100 mA
VQ,nom = 1.5 V
IQ = 100 mA
Q,nom = 6 V
0.5
0
1
0
V
0
1
2
3
4
5
6
7
0
2
4
6
8
10
VI [V]
VI [V]
Data Sheet
13
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
Dropout voltage Vdr versus
junction temperature Tj
Dropout voltage Vdr versus
output current IQ
600
600
IQ = 100 mA
Tj = −40 °C
IQ = 250 mA
Tj = 25 °C
500
500
Tj = 150 °C
VQ,nom = 6 V
VQ,nom = 6 V
400
300
200
100
0
400
300
200
100
0
0
50
100
150
0
50
100
150
200
250
Tj [°C]
IQ [mA]
Power supply ripple rejection PSRR versus
ripple frequency f
Maximum output current IQ versus
input voltage VI
100
90
80
70
60
50
40
700
600
500
400
300
200
IQ = 10 mA
30
CQ = 1 μF
VI = 13.5 V
ripple = 0.5 Vpp
VQ,nom = 1.5 V
20
10
0
V
Tj = −40 °C
100
0
Tj = 25 °C
Tj = 25 °C
VQ,forced = 0 V
Tj = 150 °C
10−2 10−1 100
101
102 103
f [Hz]
104
105
106
0
10
20
30
40
VI [V]
Data Sheet
14
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
Load regulation ΔVQ,load versus
output current change IQ
Line regulation ΔVQ,line versus
input voltage VI
10
Tj = −40 °C
Tj = −40 °C
2
IQ = 5 mA
VI = 7 V
8
Tj = 25 °C
Tj = 25 °C
CQ = 1 μF
Tj = 150 °C
Tj = 150 °C
6
0
−2
−4
−6
−8
4
2
0
−2
−4
−6
−8
−10
0
50
100
150
200
250
300
350
10
15
20
25
30
35
40
IQ [mA]
VI [V]
Equivalent series resistance of output capacitor
ESR(CQ) versus
output current IQ
103
Unstable Region
102
101
Stable Region
100
CQ = 1 μF
−40°C ≤ T ≤ 150°C
10−1
0
50
100
150
200
250
300
350
IQ [mA]
Data Sheet
15
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
4.3
Current consumption
Table 5
Electrical characteristics current consumption
Tj = -40°C to 150°C, VI = 13.5 V (unless otherwise specified)
Typical values are given at Tj = 25°C
Parameter
Symbol
Values
Unit Note or Test Condition Number
Min. Typ. Max.
Current consumption
Iq = II
Iq,off
Iq,off
Iq
–
–
–
–
–
–
1
µA
µA
µA
µA
µA
VEN = 0 V; Tj < 105°C
VEN = 0.4 V; Tj < 125°C
P_5.3.1
P_5.3.3
P_5.3.4
P_5.3.5
P_5.3.6
Current consumption
Iq = II
–
2
Current consumption
Iq = II - IQ
17
20
22
25
30
33
IQ = 0.05 mATj
Tj = 25°C
Current consumption
Iq = II - IQ
Iq
IQ = 0.05 mA
Tj < 125°C
1) IQ = 350 mA
Tj < 125°C
Current consumption
Iq = II - IQ
Iq
1) Not subject to production test, specified by design
Data Sheet
16
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
4.4
Typical performance characteristics current consumption
Current consumption Iq versus
output current IQ
Current consumption Iq versus
input voltage VI
30
25
20
15
10
60
50
40
30
20
10
0
Tj = −40 °C
Tj = 25 °C
Tj = 150 °C
Tj = −40 °C
Tj = 25 °C
Tj = 125 °C
5
VI = 13.5 V
0
0
50
100
150
IQ [mA]
200
250
300
350
10
15
20
25
VI [V]
30
35
40
Current consumption Iq versus
junction temperature Tj
40
35
30
25
20
15
10
5
VI = 13.5 V
IQ = 50 μA
0
−40
0
50
100
150
Tj [°C]
Data Sheet
17
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
4.5
Enable
The TLS835B2ELV can be switched on and off by the enable feature. Applying a “high” level as specified below
with VEN ≥ 2 V to the EN pin enables the device. Applying a “low” level as specified below withVEN ≤ 0.8 V shuts
down the device. The enable feature has a built-in hysteresis to avoid toggling between the ON/OFF state,
when a signal with slow slope is applied to the EN pin.
Table 6
Electrical characteristics enable
Tj = -40°C to 150°C, VI = 13.5 V, all voltages with respect to ground (unless otherwise specified)
Typical values are given at Tj = 25°C
Parameter
Symbol
Values
Unit Note or
Test Condition
Number
Min. Typ. Max.
Enable “high” input voltage
Enable “low” input voltage
Enable threshold hysteresis
Enable “high” input current
Enable “high” input current
VEN,H
VEN,L
VEN,Hy
IEN,H
IEN,H
REN
2
–
–
V
–
P_5.5.1
P_5.5.2
P_5.5.3
P_5.5.4
P_5.5.5
P_5.5.6
–
–
0.8
–
V
–
90
–
–
mV
µA
µA
MΩ
–
–
1
VEN = 5 V
VEN ≤ 18 V
–
–
–
6
Enable internal pull-down
resistor
2.8
10
20
Data Sheet
18
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Block description and electrical characteristics
4.6
Typical performance characteristics enable
Output voltage VQ versus
time t (EN switched on)
Output voltage VQ versus
time t (EN switched on)
7
9
VQ for T =−40 °C
VQ for T =−40 °C
j
j
8
7
6
5
4
3
2
1
0
VQ for T = 25 °C
VQ for T = 25 °C
j
j
6
VQ for T = 150 °C
VQ for T = 150 °C
j
j
VEN
VEN
5
4
3
2
VI = 13.5 V
Q = 100 mA
Q,nom = 1.5 V
VI = 13.5 V
Q = 100 mA
Q,nom = 6 V
I
V
1
0
I
V
0
0.5
1
1.5
0
0.5
1
1.5
t [ms]
t [ms]
Enable input current IEN versus
enable input voltage VEN
20
Tj =−40 °C
18
Tj = 25 °C
Tj = 150 °C
16
14
12
10
8
6
4
2
0
0
10
20
30
40
VEN [V]
Data Sheet
19
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Application information
5
Application information
5.1
Application diagram
Note:
The following information is given as a hint for the implementation of the device only and shall not
be regarded as a description or warranty of a certain functionality, condition or quality of the device.
Regulated
Output Voltage
Supply
IQ
II
I
Q
DI1
Current
Limitation
R1
EN
CQ
ADJ
1 μF
Enable
DI2
CI1
CI2
RLOAD
VI
VQ
Bandgap
Reference
<45V
10 μF 100 nF
R2
Temperature
Shutdown
ESR
GND
e.g. Ignition
Figure 5
Application diagram
Note:
This is a very simplified example of an application circuit. The function must be verified in the real
application.
5.2
Selection of external components
5.2.1
Input pin
Figure 5 shows an example of the input circuitry for a linear voltage regulator. A ceramic capacitor at the
input, in the range of 100 nF to 470 nF, is recommended to filter out the high frequency disturbances imposed
by the line, for example ISO pulses 3a/b. This capacitor must be placed very close to the input pin of the linear
voltage regulator on the PCB.
An aluminum electrolytic capacitor in the range of 10 µF to 470 µF is recommended as an input buffer to
smooth out high energy pulses, such as ISO pulses 2a. This capacitor must be placed close to the input pin of
the linear voltage regulator.
An overvoltage suppressor diode can be used to further suppress any high voltage beyond the maximum
rating of the linear voltage regulator and to protect the device from damage due to overvoltage.
The external components at the input pin are optional, but they are recommended to deal with possible
external disturbances.
5.2.2
Output pin
An output capacitor is mandatory for the stability of linear voltage regulators. Furthermore it serves as an
energy buffer during load jumps, to compensate and maintain a constant output voltage potential. It must be
dimensioned according to the specific requirements of the application. The requirements for the output
capacitor are given in “Functional range” on Page 8.
Data Sheet
20
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Application information
TLS835B2ELV is designed to also be stable with low ESR capacitors. According to the automotive
requirements, ceramic capacitors with X5R or X7R dielectrics are recommended.
The output capacitor should be placed as close as possible to the voltage regulator’s output pin and GND pin
and on the same side of the PCB as the regulator itself.
In case of input voltage or load current transients, the capacitance should be dimensioned accordingly. The
configuration has to be verified in the real application to ensure that the output stability requirements are
fulfilled.
5.2.3
Resistor divider R1, R2
The resistor divider can be calculated according to Equation (5.1):
R1
R2
VQ
=
− 1
VADJ
(5.1)
with
•
•
VQ: output voltage
ADJ: Vref, reference voltage
V
5.3
Thermal considerations
From the known input voltage, the output voltage and the load profile of the application, the total power
dissipation can be calculated as follows:
PD = (VI VQ)IQ + VIIq
(5.2)
with
•
•
•
•
•
PD: continuous power dissipation
VI: input voltage
VQ: output voltage
IQ: output current
Iq: quiescent current
The maximum acceptable thermal resistance RthJA is given by:
Tj,max − Ta
RthJA
=
PD
(5.3)
with
•
•
Tj,max: maximum allowed junction temperature
Ta: ambient temperature
Based on the above calculation the proper PCB type and the necessary heat sink area can be determined by
referencing the specification for “Thermal resistance” on Page 9.
5.4
Reverse polarity protection
TLS835B2ELV is not protected against reverse polarity faults and must be protected by external components
against negative supply voltage. An external reverse polarity diode is necessary. The absolute maximum
ratings of the device as specified in “Absolute maximum ratings” on Page 7 must be maintained.
Data Sheet
21
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Application information
5.5
Further application information
For further information you may contact https://www.infineon.com/
Data Sheet
22
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Package information
6
Package information
0.35 x 45˚
1)
0.1 C D
±0.1
3.9
+0.06
9
0.1
0.08
C
C
0.64±0.25
0.2
0.65
2)
±0.05
±0.2
0.25
6
M
M
D 8x
0.15
C A-B D 14x
D
Bottom View
±0.2
3
A
1
7
14
8
1
7
14
8
Exposed
Diepad
B
0.1 C A-B 2x
1)
±0.1
4.9
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Does not include dambar protrusion
Figure 6
PG-SSOP-141)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant
with government regulations the device is available as a green product. Green products are RoHS-Compliant
(i.e. Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
Further information on packages
https://www.infineon.com/packages
1) Dimensions in mm
Data Sheet
23
Rev. 1.1
2018-09-17
OPTIREG™ Linear TLS835B2ELV
Low Dropout Linear Voltage Regulator
Revision history
7
Revision history
Revision Date
Changes
2018-09-17 Editorial changes
Updated T to Tj in graph of “Equivalent series resistance of output capacitor
1.1
ESR(CQ) versus output current IQ”
Added footnote to overtemperature shutdown specification
Added VQ and removed VI in the test condition of the dropout voltage in electrical
characteristics
1.0
2018-03-02 Initial Version
Data Sheet
24
Rev. 1.1
2018-09-17
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
IMPORTANT NOTICE
The information given in this document shall in no For further information on technology, delivery terms
Edition 2018-09-17
Published by
Infineon Technologies AG
81726 Munich, Germany
event be regarded as a guarantee of conditions or and conditions and prices, please contact the nearest
characteristics ("Beschaffenheitsgarantie").
Infineon Technologies Office (www.infineon.com).
With respect to any examples, hints or any typical
values stated herein and/or any information regarding
the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities
of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any
third party.
In addition, any information given in this document is
subject to customer's compliance with its obligations
stated in this document and any applicable legal
requirements, norms and standards concerning
customer's products and any use of the product of
Infineon Technologies in customer's applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer's technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to
such application.
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
© 2018 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.
Document reference
Z8F61183983
相关型号:
TLS835D2EL VSE
TLS835D2 是线性电压调节器,具有高性能、极低压差线性电压和极低的静态电流。稳压器的输入电压范围为 3 V 至 40 V,静态电流极低,仅 20 μA,,非常适合汽车或永久连接电池的其他电源系统。
INFINEON
TLS850B0TB V33
3V-40V的输入电压范围和 20μA 的极低静态电流使其完美适合汽车或其它永久连接电池的电源系统。新的回路概念结合了快速调节和非常高的稳定性,输出端只需要一个 1μF 的小型陶瓷电容即可。输出电流在100毫安以下时,典型的压差非常低,数值为120 mV 。工作范围从仅 3 V 的输入电压开始(扩展工作范围)。因此,TLS850B0TBV33 适用于需要在启动条件下运行的汽车系统。通过“启用”功能,可以打开和关闭器件。内部保护功能(如输出电流限制和过温关断)可防止器件因输出接地短路、过流和过热等故障而立即损坏。
INFINEON
TLS850B0TE V50
3V-40V的输入电压范围和 20μA 的极低静态电流使其完美适合汽车或其它永久连接电池的电源系统。新环路概念结合了快速调节并确保了极高的稳定性。输出电流在100毫安以下时,典型的压差低于100mV。工作范围从仅 3 V 的输入电压开始(扩展工作范围)。因此,TLS850B0TEV50 适用于需要在启动条件下运行的汽车系统。通过“启用”功能,可以打开和关闭器件。内部保护功能(如输出电流限制和过温关断)可防止器件因输出接地短路、过流和过热等故障而立即损坏。
INFINEON
TLS850D0TA V50
TLS850D0TAV50 是一款高性能的极低压差线性稳压器,采用 PG-TO263-7 封装,适用于 5 V 电源。这些稳压器的输入电压范围为 3 V 至 40 V,静态电流极低(仅 40μA),非常适合汽车或永久连接电池的任何其他电源系统。TLS850D0TAV50 的输出电压精度为 2%,最大输出电流高达 500 mA。新的回路概念结合了快速调节和非常好的稳定性,输出端只需要一个 1μF 的小型陶瓷电容即可。在低于 100 mA 的电流下,该设备的典型压差非常低,仅 70 mV。工作范围从仅 3 V 的输入电压开始(扩展工作范围)。因此,TLS850D0TAV50 也适用于需要在启动条件下运行的汽车系统。
INFINEON
TLS850D0TAV33ATMA1
Fixed Positive LDO Regulator, 3.3V, 0.43V Dropout, PSFM7, TO-263 , 7 PIN
INFINEON
TLS850D0TE V50
TLS850D0TEV50 是一款高性能的极低压差线性稳压器,采用 PGTO252-5 封装,适用于 5V 电源。这些稳压器的输入电压范围为 3 V 至 40 V,静态电流极低(仅 40μA),非常适合汽车或永久连接电池的任何其他电源系统。TLS850D0TAV50 的输出电压精度为 2%,最大输出电流高达 500 mA。新的回路概念结合了快速调节和非常好的稳定性,输出端只需要一个 1μF 的小型陶瓷电容即可。在低于 100 mA 的电流下,该设备的典型压差非常低,仅 70 mV。工作范围从仅 3 V 的输入电压开始(扩展工作范围)。因此,TLS850D0TAV50 也适用于需要在启动条件下运行的汽车系统。
INFINEON
©2020 ICPDF网 联系我们和版权申明