HCS164MS [INTERSIL]
Radiation Hardened 8-Bit Serial-In/Parallel-Out Register; 抗辐射的8位串行输入/并行输出寄存器
| 型号： | HCS164MS |
| 厂家： | 
Intersil |
| 描述： | Radiation Hardened 8-Bit Serial-In/Parallel-Out Register |
| 文件： | 总9页 (文件大小：224K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HCS164MS
Radiation Hardened
8-Bit Serial-In/Parallel-Out Register
September 1995
Features
Pinouts
14 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T14, LEAD FINISH C
TOP VIEW
• 3 Micron Radiation Hardened CMOS SOS
• Total Dose 200K RAD (Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/
Bit-Day (Typ)
DS1
DS2
Q0
1
2
3
4
5
6
7
14 VCC
13 Q7
12 Q6
11 Q5
10 Q4
• Dose Rate Survivability: >1 x 1012 RAD (Si)/s
• Dose Rate Upset >1010 RAD (Si)/s 20ns Pulse
• Latch-Up-Free Under Any Conditions
Q1
Q2
Q3
9
8
MR
CP
• Fanout (Over Temperature Range)
- Standard Outputs - 10 LSTTL Loads
GND
• Military Temperature Range: -55oC to +125oC
• Significant Power Reduction Compared to LSTTL ICs
• DC Operating Voltage Range: 4.5V to 5.5V
14 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP3-F14, LEAD FINISH C
TOP VIEW
• Input Logic Levels
- VIL = 0.3 VCC Max
- VIH = 0.7 VCC Min
DS1
DS2
Q0
VCC
Q7
1
2
3
4
5
6
7
14
13
12
11
10
9
• Input Current Levels Ii ≤ 5µA at VOL, VOH
Q6
Description
The Intersil HCS164MS is a Radiation Hardened 8-bit
Serial-In/Parallel-Out Shift Register that has fully synchro-
nous serial data entry and an asynchronous master reset.
Q1
Q5
Q2
Q4
Q3
MR
CP
GND
8
The HCS164MS utilizes advanced CMOS/SOS technology
to achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
The HCS164MS is supplied in a 14 lead Ceramic flatpack
(K suffix) or a SBDIP Package (D suffix).
Ordering Information
PART NUMBER
HCS164DMSR
TEMPERATURE RANGE
SCREENING LEVEL
Intersil Class S Equivalent
Intersil Class S Equivalent
Sample
PACKAGE
14 Lead SBDIP
o
o
-55 C to +125 C
o
o
HCS164KMSR
-55 C to +125 C
14 Lead Ceramic Flatpack
14 Lead SBDIP
o
HCS164D/Sample
HCS164K/Sample
HCS164HMSR
+25 C
o
+25 C
Sample
14 Lead Ceramic Flatpack
Die
o
+25 C
Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Spec Number 518756
File Number 2465.2
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
230
HCS164MS
Functional Diagram
9
MR
R
Q
R
Q
R
R
Q
R
Q
R
Q
R
Q
R
Q
8
CL
D
CL
D
CL
D
CL
D
CL
D
CL
D
CL
D
CL
D
CP
Q
1
D1
2
D2
3
4
5
6
10
11
12
Q6
13
Q7
Q0
Q1
Q2
Q3
Q4
Q5
TRUTH TABLE
INPUTS
OUTPUTS
OPERATING MODE
Reset (Clear)
Shift
MR
L
CP
DS1
DS2
Q0
L
Q1-Q7
L-L
X
X
l
X
l
H
L
q0 -q6
q0 - q6
q0 - q6
q0 - q6
H
l
h
l
L
H
h
h
L
H
h
H
H = High Voltage Level
h = HIGH voltage level one setup time prior to the LOW-to-HIGH clock transistion
L = Low VoltageLevel
l = LOW voltage level one setup time prior to the LOW-to-HIGH clock transition.
= LOW-to-HIGH clock transition
q = Lower case letters indicate the state of the referenced input (or output) one setup time prior to the LOW-to-HIGH clock transition
Spec Number 518756
231
Specifications HCS164MS
Absolute Maximum Ratings
Reliability Information
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V
Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V
DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA
DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±25mA
(All Voltage Reference to the VSS Terminal)
Thermal Resistance
SBDIP Package. . . . . . . . . . . . . . . . . . . .
Ceramic Flatpack Package . . . . . . . . . . . 116 C/W
Maximum Package Power Dissipation at +125 C Ambient
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68W
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.43W
If device power exceeds package dissipation capability, provide heat
sinking or derate linearly at the following rate:
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5mW/ C
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 8.6mW/ C
θ
θ
JA
JC
o
o
74 C/W
24 C/W
o
o
30 C/W
o
o
o
Storage Temperature Range (TSTG) . . . . . . . . . . . -65 C to +150 C
o
Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265 C
o
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175 C
o
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
o
CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent
damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed
under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation..
Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Input Rise and Fall Times at 4.5 VCC (TR, TF) . . . . . . . .500ns Max
Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . 0.0V to 30% of VCC
Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . 70% of VCC to VCC
o
o
Operating Temperature Range (T ) . . . . . . . . . . . . -55 C to +125 C
A
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
GROUP
A SUB-
LIMITS
(NOTE 1)
PARAMETER
SYMBOL
CONDITIONS
GROUPS
TEMPERATURE
MIN
MAX
UNITS
µA
o
Quiescent Current
ICC
VCC = 5.5V,
VIN = VCC or GND
1
2, 3
1
+25 C
-
40
o
o
+125 C, -55 C
-
750
µA
o
Output Current
(Sink)
IOL
IOH
VOL
VCC = 4.5V, VIH = 4.5V,
VOUT = 0.4V, VIL = 0V
+25 C
4.8
4.0
-4.8
-4.0
-
-
mA
mA
mA
mA
V
o
o
2, 3
1
+125 C, -55 C
-
-
o
Output Current
(Source)
VCC = 4.5V, VIH = 4.5V,
VOUT = VCC -0.4V,
VIL = 0V
+25 C
o
o
2, 3
1, 2, 3
+125 C, -55 C
-
o
o
o
Output Voltage Low
VCC = 4.5V, VIH = 3.15V,
+25 C, +125 C, -55 C
0.1
IOL = 50µA, VIL = 1.35V
o
o
o
VCC = 5.5V, VIH = 3.85V,
IOL = 50µA, VIL = 1.65V
1, 2, 3
1, 2, 3
1, 2, 3
+25 C, +125 C, -55 C
-
0.1
V
V
V
o
o
o
Output Voltage High
VOH
VCC = 4.5V, VIH = 3.15V,
IOH = -50µA, VIL = 1.35V
+25 C, +125 C, -55 C
VCC
-0.1
-
-
o
o
o
VCC = 5.5V, VIH = 3.85V,
IOH = -50µA, VIL = 1.65V
+25 C, +125 C, -55 C
VCC
-0.1
o
Input Leakage
Current
IIN
FN
VCC = 5.5V, VIN = VCC or
GND
1
+25 C
-
-
-
±0.5
±5.0
-
µA
µA
-
o
o
2, 3
+125 C, -55 C
o
o
o
Noise Immunity
Functional Test
VCC = 4.5V,
VIH = 0.70(VCC),
VIL = 0.30(VCC) (Note 2)
7, 8A, 8B
+25 C, +125 C, -55 C
NOTES:
1. All voltages reference to device GND.
2. For functional tests, VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.
Spec Number 518756
232
Specifications HCS164MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
GROUP
LIMITS
(NOTES 1, 2)
A SUB-
PARAMETER
CP to Qn
SYMBOL
CONDITIONS
GROUPS
TEMPERATURE
MIN
MAX
32
UNITS
ns
o
TPLH
TPHL
VCC = 4.5V
9
+25 C
2
2
2
2
o
o
VCC = 4.5V
VCC = 4.5V
VCC = 4.5V
10, 11
9
+125 C, -55 C
37
ns
o
MR to Qn
NOTES:
TPHL
+25 C
32
ns
o
o
10, 11
+125 C, -55 C
37
ns
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
LIMITS
(NOTE 1)
PARAMETER
SYMBOL
CONDITIONS
TEMPERATURE
MIN
MAX
135
165
10
UNITS
pF
o
Capacitance Power Dissipation
CPD
VCC = 5.0V, f = 1MHz
+25 C
-
-
-
-
-
-
o
o
+125 C, -55 C
pF
o
Input Capacitance
Output Transition Time
NOTE:
CIN
VCC = 5.0V, f = 1MHz
VCC = 4.5V
+25 C
pF
o
o
+125 C, -55 C
10
pF
o
TTHL
TTLH
+25 C
15
ns
o
o
+125 C, -55 C
22
ns
1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly
tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics.
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS
200K RAD
LIMITS
(NOTES 1, 2)
PARAMETER
Quiescent Current
Output Current (Sink)
SYMBOL
ICC
CONDITIONS
TEMPERATURE
MIN
-
MAX
0.75
-
UNITS
mA
o
VCC = 5.5V, VIN = VCC or GND
+25 C
o
IOL
VCC = 4.5V, VIN = VCC or GND,
VOUT = 0.4V
+25 C
4.0
mA
o
Output Current
(Source)
IOH
VOL
VOH
IIN
VCC = 4.5V, VIN = VCC or GND,
VOUT = VCC -0.4V
+25 C
-4.0
-
-
0.1
-
mA
V
o
Output Voltage Low
Output Voltage High
Input Leakage Current
VCC = 4.5V and 5.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), IOL = 50µA
+25 C
o
VCC = 4.5V and 5.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), IOH = -50µA
+25 C
VCC
-0.1
V
o
VCC = 5.5V, VIN = VCC or GND
+25 C
-
±5
µA
Spec Number 518756
233
Specifications HCS164MS
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
200K RAD
LIMITS
(NOTES 1, 2)
PARAMETER
SYMBOL
CONDITIONS
TEMPERATURE
MIN
MAX
UNITS
o
Noise Immunity
Functional Test
FN
VCC = 4.5V, VIH = 0.70(VCC),
VIL = 0.30(VCC), (Note 3)
+25 C
-
-
-
o
CP to Qn
TPHL
TPLH
VCC = 4.5V
VCC = 4.5V
+25 C
2
2
37
37
ns
ns
o
MR to Qn
NOTES:
TPHL
+25 C
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.
3. For functional tests VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.
o
TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25 C)
GROUP B
PARAMETER
SUBGROUP
DELTA LIMIT
12µA
ICC
5
5
IOL/IOH
-15% of 0 Hour
TABLE 6. APPLICABLE SUBGROUPS
GROUP A SUBGROUPS
CONFORMANCE GROUPS
METHOD
100%/5004
100%/5004
100%/5004
100%/5004
100%/5004
100%/5004
100%/5004
Sample/5005
Sample/5005
READ AND RECORD
ICC, IOL/H
Initial Test (Preburn-In)
1, 7, 9
1, 7, 9
Interim Test I (Postburn-In)
Interim Test II (Postburn-In)
PDA
ICC, IOL/H
ICC, IOL/H
1, 7, 9
1, 7, 9, Deltas
Interim Test III (Postburn-In)
PDA
1, 7, 9
ICC, IOL/H
1, 7, 9, Deltas
Final Test
2, 3, 8A, 8B, 10, 11
1, 2, 3, 7, 8A, 8B, 9, 10, 11
1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas
Group A (Note 1)
Group B
Subgroup B-5
Subgroups 1, 2, 3, 9, 10, 11,
(Note 2)
Subgroup B-6
Sample/5005
Sample/5005
1, 7, 9
1, 7, 9
Group D
NOTES:
1. Alternate group A testing in accordance with method 5005 of MIL-STD-883 may be exercised.
2. Table 5 parameters only.
Spec Number 518756
234
Specifications HCS164MS1
TABLE 7. TOTAL DOSE IRRADIATION
TEST
READ AND RECORD
CONFORMANCE
GROUPS
METHOD
PRE RAD
POST RAD
PRE RAD
1, 9
POST RAD
Group E Subgroup 2
NOTE:
5005
1, 7, 9
Table 4
Table 4 (Note 1)
1. Except FN test which will be performed 100% Go/No-Go.
TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS
OSCILLATOR
OPEN
STATIC BURN-IN I TEST CONNECTIONS (Note 1)
3 - 6, 10 - 13 1, 2, 7 - 9
STATIC BURN-IN II TEST CONNECTIONS (Note 1)
3 - 6, 10 - 13
DYNAMIC BURN-IN TEST CONNECTIONS (Note 2)
3 - 6, 10 - 13
GROUND
1/2 VCC = 3V ± 0.5V
VCC = 6V ± 0.5V
50kHz
25kHz
-
-
14
-
-
-
-
7
1, 2, 8, 9, 14
9, 14
-
7
8
1, 2
NOTES:
1. Each pin except VCC and GND will have a resistor of 10KΩ ± 5% for static burn-in
2. Each pin except VCC and GND will have a resistor of 1KΩ ± 5% for dynamic burn-in
TABLE 9. IRRADIATION TEST CONNECTIONS
OPEN
GROUND
VCC = 5V ± 0.5V
1, 2, 8, 9, 14
3 - 6, 10 - 13
7
NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing.
Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures.
Spec Number 518756
235
HCS164MS
Intersil Space Level Product Flow - ‘MS’
Wafer Lot Acceptance (All Lots) Method 5007
(Includes SEM)
100% Interim Electrical Test 1 (T1)
100% Delta Calculation (T0-T1)
GAMMA Radiation Verification (Each Wafer) Method 1019,
4 Samples/Wafer, 0 Rejects
100% Static Burn-In 2, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Nondestructive Bond Pull, Method 2023
Sample - Wire Bond Pull Monitor, Method 2011
Sample - Die Shear Monitor, Method 2019 or 2027
100% Internal Visual Inspection, Method 2010, Condition A
100% Interim Electrical Test 2 (T2)
100% Delta Calculation (T0-T2)
100% PDA 1, Method 5004 (Notes 1and 2)
100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or
100% Temperature Cycle, Method 1010, Condition C,
10 Cycles
Equivalent, Method 1015
100% Interim Electrical Test 3 (T3)
100% Delta Calculation (T0-T3)
100% Constant Acceleration, Method 2001, Condition per
Method 5004
100% PDA 2, Method 5004 (Note 2)
100% Final Electrical Test
100% PIND, Method 2020, Condition A
100% External Visual
100% Fine/Gross Leak, Method 1014
100% Radiographic, Method 2012 (Note 3)
100% External Visual, Method 2009
Sample - Group A, Method 5005 (Note 4)
100% Data Package Generation (Note 5)
100% Serialization
100% Initial Electrical Test (T0)
100% Static Burn-In 1, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
NOTES:
1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1.
2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the
failures from subgroup 7.
3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004.
4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005.
5. Data Package Contents:
• Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number,
Quantity).
• Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage.
• GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test
equipment, etc. Radiation Read and Record data on file at Intersil.
• X-Ray report and film. Includes penetrometer measurements.
• Screening, Electrical, and Group A attributes (Screening attributes begin after package seal).
• Lot Serial Number Sheet (Good units serial number and lot number).
• Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test.
• The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed
by an authorized Quality Representative.
Spec Number 518756
236
HCS164MS
AC Load Circuit
AC Timing Diagrams
VIH
DUT
TEST
POINT
INPUT
VS
VIL
TPLH
CL
RL
TPHL
VOH
VOL
VOH
VOL
VS
OUTPUT
CL = 50pF
RL = 500Ω
TTLH
TTHL
80%
80%
20%
20%
OUTPUT
AC VOLTAGE LEVELS
PARAMETER
VCC
HCS
4.50
4.50
2.25
0
UNITS
V
V
V
V
V
VIH
VS
VIL
GND
0
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
EUROPE
ASIA
Intersil Corporation
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
Intersil (Taiwan) Ltd.
Taiwan Limited
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (321) 724-7000
FAX: (321) 724-7240
Spec Number 518756
237
HCS164MS
Die Characteristics
DIE DIMENSIONS:
95 x 94mils
METALLIZATION:
Type: AlSi
Metal Thickness: 11kÅ ± 1kÅ
GLASSIVATION:
Type: SiO2
Thickness: 13kÅ ± 2.6kÅ
WORST CASE CURRENT DENSITY:
< 2.0 x 105A/cm2
BOND PAD SIZE:
100µm x 100µm
4 mils x 4 mils
Metallization Mask Layout
HCS164MS
DS2
(2)
DS1
(1)
VCC
(14)
Q7
(13)
Q6
(12)
Q0 (3)
Q1 (4)
NC
(11) Q5
NC
(10) Q4
(5)
Q2
(6)
Q3
(7)
GND
(8)
CP
(9)
(MR)
Spec Number 518756
238
相关型号：
HCS165D/SAMPLE
HC/UH SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, COMPLEMENTARY OUTPUT, CDIP16, SIDE BRAZED, CERAMIC, DIP-16
RENESAS
HCS165K/SAMPLE
HC/UH SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, COMPLEMENTARY OUTPUT, CDFP16, CERAMIC, DFP-16
RENESAS
HCS166D/SAMPLE
HC/UH SERIES, 8-BIT RIGHT PARALLEL IN SERIAL OUT SHIFT REGISTER, TRUE OUTPUT, CDIP16, SIDE BRAZED, CERAMIC, DIP-16
RENESAS
©2020 ICPDF网 联系我们和版权申明