IS9-705RH-Q [INTERSIL]
Radiation Hardened Power-Up/Down Microprocessor Reset Circuit; 抗辐射电/断电微处理器复位电路型号: | IS9-705RH-Q |
厂家: | Intersil |
描述: | Radiation Hardened Power-Up/Down Microprocessor Reset Circuit |
文件: | 总2页 (文件大小:500K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IS-705RH
TM
Data Sheet
December 2001
FN4703.4
Radiation Hardened Power-Up/Down
Microprocessor Reset Circuit
Features
• Electrically Screened to SMD # 5962-00538
The Radiation Hardened IS-705RH is
a monolithic device that monitors the
• QML Qualified per MIL-PRF-38535 Requirements
TM
• Radiation Hardness
power supply voltage used by
satellite control units and provides a
- Total Dose. . . . . . . . . . . . . . . . . . . . . 100 krad(Si) (Max)
2
reset output pulse during power-up and power-down. The
reset threshold is 4.65V (Typ) and the reset pulse width is set
at 200ms (Typ). A watchdog circuit is incorporated for easy
interfacing with microprocessors and controllers. If the
watchdog input has not been toggled within a preset
1.6s (Typ) time period, an output signal is generated, which
can be used as an interupt. The power function input (PFI)
may be used to monitor other voltage levels. The circuit has a
1.25V (Typ) threshold and provides a PFO output when low
voltage is detected. An active-low manual reset input in also
provided for direct control of the reset function.
- Single Event Latch-up . . . . . . . . . . . . >90MeV/mg/cm
• Precision 4.65V Voltage Monitor
• Wide Operating Supply Range . . . . . . . . . . . 1.2V to 5.5V
• Low Supply Current . . . . . . . . . . . . . . . . . . . . 420µA (Typ)
• 200ms (Typ) RESET Pulse Width
Applications
• Flight Computers
• Controllers
Constructed with the Intersil UHF2X-CMOS process, these
devices have been specifically designed to provide highly
reliable performance in harsh radiation environments. This
process has been tested for single event latch-up and has
• Critical Microprocessor Power Monitoring
• Reliable Replacement of Discrete Solutions
Ordering Information
2
demonstrated an immunity to 90MeV/mg/cm .
INTERNAL
MKT. NUMBER
TEMP. RANGE
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
o
ORDERING NUMBER
5962R0053801QXC
5962R0053801VXC
5962R0053801V9A
IS9-705RH/Proto
( C)
IS9-705RH-8
IS9-705RH-Q
IS0-705RH-Q
IS9-705RH/Proto
-55 to 125
-55 to 125
-55 to 125
-55 to 125
Detailed Electrical Specifications for these devices are
contained in SMD 5962-00538. A “hot-link” is provided
on our homepage for downloading.
Pinout
IS9-705RH
FLATPACK
TOP VIEW
MR
1
2
3
4
8
7
6
5
WDO
RESET
WDI
V
CC
GND
PFI
PFO
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2001. All Rights Reserved
1
Star*Power™ is a trademark of Intersil Americas Inc.
IS-705RH
Die Characteristics
DIE DIMENSIONS:
Substrate:
1500µm x 1830µm (59 mils x 72 mils)
UHF2X-CMOS
Thickness: 483µm ±25.4µm (19 mils ±1 mil)
Backside Finish:
INTERFACE MATERIALS
Glassivation
Silicon
ASSEMBLY RELATED INFORMATION
Substrate Potential:
Type: Nitride (Si N ) over Silox (SiO )
3
4
2
Nitride Thickness: 4.0kÅ ±1.0kÅ
Silox Thickness: 12.0kÅ ±4.0kÅ
Backside internally connected to GND
(May be left floating or connected to GND.)
Top Metallization
ADDITIONAL INFORMATION
Worst Case Current Density:
Top Metal 3: TiAlCu
Thickness: 0.8µm ±0.02µm
Metal 1 and 2: TiAlCu
5
2
<2.0 x 10 A/cm
Thickness: 0.4µm ±0.01µm
Metallization Mask Layout
IS-705RH
MR (1)
WDO (8)
VCC (2)
RESET (7)
WDI (6)
GND (3)
PFI (4)
PFO (5)
NOTES:
1. Octagonal trim pads should be left unconnected.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
2
相关型号:
IS900-SMT&R
Optocoupler - IC Output, 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 1 Mbps, SURFACE MOUNT, DIP-6
ISOCOM
IS900SMT&R
Logic IC Output Optocoupler, 1-Element, 5300V Isolation, 1MBps, SURFACE MOUNT PACKAGE-6
ISOCOM
©2020 ICPDF网 联系我们和版权申明