ISL28127SOICEVAL1Z [INTERSIL]
Precision Single and Dual Low Noise Operational Amplifiers; 单精度和双低噪声运算放大器型号: | ISL28127SOICEVAL1Z |
厂家: | Intersil |
描述: | Precision Single and Dual Low Noise Operational Amplifiers |
文件: | 总23页 (文件大小:1800K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Precision Single and Dual Low Noise Operational
Amplifiers
ISL28127, ISL28227
Features
• Very Low Voltage Noise. . . . . . . . . . . . .2.5nV/Hz
• Low Input Offset . . . . . . . . . . . . . . . 70µV, Max.
• Superb Offset Drift . . . . . . . . . . . 0.5µV/°C, Max.
• Input Bias Current . . . . . . . . . . . . . . 10nA, Max.
• Wide Supply Range. . . . . . . . . . . . . . 4.5V to 40V
• Gain-bandwidth Product .10MHz Unity Gain Stable
• No Phase Reversal
The ISL28127 and ISL28227 are very high precision
amplifiers featuring very low noise, low offset voltage,
low input bias current and low temperature drift making
them the ideal choice for applications requiring both high
DC accuracy and AC performance. The combination of
precision, low noise, and small footprint provides the
user with outstanding value and flexibility relative to
similar competitive parts.
Applications for these amplifiers include precision active
filters, medical and analytical instrumentation, precision
power supply controls, and industrial controls.
Applications*(see page 20)
• Precision Instruments
• Medical Instrumentation
• Industrial Controls
• Active Filter Blocks
• Data Acquisition
The ISL28127 single and ISL28227 dual are available in
an 8 Ld SOIC, TDFN and MSOP packages. All devices are
offered in standard pin configurations and operate over
the extended temperature range to -40°C to +125°C.
• Power Supply Control
Related Literature*(see page 20)
• AN1508: ISL281X7SOICEVAL1Z Evaluation Board
User’s Guide
Typical Application
Input Noise Voltage Spectral
Density
C
1
100
VS = ±19V
AV = 1
1.5nF
V
+
-
10
OUTPUT
R
R
V
2
1
IN
+
95.3
232
68.3nF
C
2
V
-
1
0.1
Sallen-Key Low Pass Filter (1MHz)
1
10
100
1k
10k
100k
FREQUENCY (Hz)
March 18, 2010
FN6633.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2009, 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL28127, ISL28227
.
Ordering Information
PART NUMBER
(Notes 3, 4)
PART
MARKING
VOS (MAX)
(µV)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL28127FBZ (Note 1)
28127 FBZ
70
8 Ld SOIC
M8.15E
Coming Soon
TBD (B Grade)
ISL28127FRTBZ (Note 2)
127Z
8 Ld TDFN
L8.3x3A
L8.3x3A
Coming Soon
ISL28127FRTZ (Note 2)
150 (C Grade)
TBD (B Grade)
-C 127Z
8 Ld TDFN
Coming Soon
ISL28127FUBZ (Note 2)
8127Z
8 Ld MSOP
8 Ld MSOP
8 Ld SOIC
M8.118
M8.118
M8.15E
ISL28127FUZ (Note 2)
ISL28227FBZ (Note 2)
8127Z -C
28227 FBZ
150 (C Grade)
75
Coming Soon
TBD (B Grade)
ISL28227FRTBZ (Note 2)
227Z
8 Ld TDFN
8 Ld TDFN
8 Ld MSOP
8 Ld MSOP
L8.3x3A
L8.3x3A
M8.118
M8.118
Coming Soon
ISL28227FRTZ (Note 2)
150 (C Grade)
TBD (B Grade)
150 (C Grade)
-C 227Z
8227Z
Coming Soon
ISL28227FUBZ (Note 2)
Coming Soon
ISL28227FUZ (Note 2)
8227Z -C
ISL28127SOICEVAL1Z
Evaluation Board
1. Add “-T7” or “-T13” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. Add “-T13” suffix for tape and reel.Please refer to TB347 for details on reel specifications.
3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach
materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both
SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
4. For Moisture Sensitivity Level (MSL), please see device information page for ISL28127, ISL28227. For more information on
MSL please see techbrief TB363.
FN6633.3
March 18, 2010
2
ISL28127, ISL28227
Pin Configurations
ISL28127
(8 LD SOIC, MSOP)
TOP VIEW
ISL28227
(8 LD SOIC, MSOP)
TOP VIEW
NC
-IN_A
+IN_A
V -
1
2
3
4
8
7
6
5
NC
V+
V
A
1
2
3
4
8
7
6
5
V+
OUT
-IN_A
+IN_A
V -
V
B
- +
OUT
- +
V
A
-IN_B
OUT
+ -
NC
+IN_B
ISL28127
(8 LD TDFN)
TOP VIEW
ISL28227
(8 LD TDFN)
TOP VIEW
V _A
OUT
V+
8
NC
NC
V+
1
1
8
-IN_A
V
_B
OUT
-IN
2
3
7
6
2
3
7
6
- +
- +
+IN_A
-IN_B
+IN
VOUT
+ -
PD
PD
V- 4
5 +IN_B
V- 4
5 NC
Pin Descriptions
ISL28127
ISL28227
(8 LD SOIC,
ISL28127 (8 LD SOIC, ISL28227
PIN
NAME
EQUIVALENT
CIRCUIT
8 LD MSOP) (8 LD TDFN) 8 LD MSOP) (8 LD TDFN)
DESCRIPTION
Amplifier non-inverting input
Amplifier A non-inverting input
Negative power supply
Amplifier B non-inverting input
Amplifier inverting input
Amplifier B inverting input
Amplifier output
3
+IN
+IN_A
V-
Circuit 1
Circuit 1
Circuit 3
Circuit 1
Circuit 1
Circuit 1
Circuit 2
Circuit 2
Circuit 3
Circuit 2
Circuit 1
-
3
4
3
4
5
3
4
5
4
2
6
7
+IN_B
-IN
6
6
-IN_B
VOUT
7
8
1
2
7
8
1
2
V
OUTB
V+
Amplifier B output
7
Positive power supply
6
2
V
OUTA
Amplifier A output
-IN_A
NC
Amplifier A inverting input
1, 5, 8
1, 5, 8
PD
Not Connected – This pin is not
electrically connected internally.
PD
-
Thermal Pad. Pad should be
connecte to lowest potential source
in the circuit.
V+
V-
V+
V+
OUT
V-
CAPACITIVELY
TRIGGERED
ESD CLAMP
IN-
IN+
V-
CIRCUIT 1
CIRCUIT 2
CIRCUIT 3
FN6633.3
March 18, 2010
3
ISL28127, ISL28227
Absolute Maximum Ratings
Thermal Information
Maximum Supply Voltage . . . . . . . . . . . . . . . . . . . . . . 42V
Maximum Differential Input Current . . . . . . . . . . . . . 20mA
Maximum Differential Input Voltage . . . . . . . . . . . . . . .0.5V
Min/Max Input Voltage . . . . . . . . . . .V- - 0.5V to V+ + 0.5V
Max/Min Input Current for
Input Voltage >V+ or <V- . . . . . . . . . . . . . . . . . .±20mA
Output Short-Circuit Duration
(1 Output at a Time) . . . . . . . . . . . . . . . . . . . . Indefinite
ESD Tolerance
Human Body Model (Tested per JESD22-A114F)
ISL28127. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0kV
ISL28227. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0kV
Machine Model (Tested per EIA/JESD22-A115-A). . . . 500V
Charged Device Model (Tested per JESD22-C101D) . . 1.5kV
Di-electrically Isolated PR40 process. . . . . . . . Latch-up free
Thermal Resistance (Typical)
θ
JA (°C/W)
θ
JC (°C/W)
8 Ld SOIC (Note 5, 7)
ISL28127 . . . . . . . . . . . . . . . . .
ISL28227 . . . . . . . . . . . . . . . . .
8 Ld TDFN (Notes 5, 6)
ISL28127 . . . . . . . . . . . . . . . . .
ISL28227 . . . . . . . . . . . . . . . . .
8 Ld MSOP (Note 5, 7)
ISL28127 . . . . . . . . . . . . . . . . .
ISL28227 . . . . . . . . . . . . . . . . .
Storage Temperature Range. . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
120
110
60
55
48
47
7
6
155
150
50
45
Operating Conditions
Ambient Operating Temperature Range . . . -40°C to +125°C
Maximum Operating Junction Temperature . . . . . . . +150°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact
product reliability and result in failures not covered by warranty.
NOTES:
5. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief
TB379 for details.
6. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
7. For θJC, the “case temp” location is taken at the package top center.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless
otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: T = T = T
J
C
A
Electrical Specifications VS ±15V, VCM = 0, VO = 0V, RL = Open, TA= +25°C, unless otherwise noted. Boldface limits
apply over the operating temperature range, -40°C to +125°C. Temperature data
established by characterization.
MIN
MAX
PARAMETER
DESCRIPTION
CONDITIONS
ISL28127
(Note 8)
TYP
10
-
(Note 8)
UNIT
µV
VOS
Offset Voltage; SOIC Package
-70
-120
-75
70
120
75
µV
ISL28227
10
-
µV
-150
-150
-250
150
150
250
µV
Offset Voltage;
MSOP, TDFN Grade C Package
ISL28127
ISL28227
10
-
µV
µV
TCVOS
Offset Voltage Drift;
SOIC Pacakge
ISL28127
ISL28227
-0.5
-0.75
-1
0.1
0.1
0.1
0.5
0.75
1
µV/°C
µV/°C
µV/°C
Offset Voltage Drift;
MSOP, TDFN, Grade C
ISL28127
ISL28227
IOS
Input Offset Current
-10
-12
-10
-12
-13
-12
115
115
1
10
12
10
12
13
12
-
nA
nA
nA
nA
V
-
1
IB
Input Bias Current
-
VCM
CMRR
Input Voltage Range
Guaranteed by CMRR
-
-
V
Common-Mode Rejection Ratio
VCM = -13V to +13V
120
-
dB
dB
VCM = -12V to +12V
-
FN6633.3
March 18, 2010
4
ISL28127, ISL28227
Electrical Specifications VS ±15V, VCM = 0, VO = 0V, RL = Open, TA= +25°C, unless otherwise noted. Boldface limits
apply over the operating temperature range, -40°C to +125°C. Temperature data
established by characterization. (Continued)
MIN
MAX
PARAMETER
DESCRIPTION
CONDITIONS
VS = ±2.25V to ±20V
VS = ±3V to ± 20V
VS = ±2.25V to ±20V
VS = ±3V to ± 20V
(Note 8)
TYP
125
-
(Note 8)
UNIT
dB
PSRR
Power Supply Rejection Ratio
ISL28127
115
115
110
-
-
-
-
-
dB
Power Supply Rejection Ratio
ISL28227
117
-
dB
110
1000
dB
AVOL
VOH
Open-Loop Gain
VO = -13V to +13V
RL = 10kΩ to ground
1500
V/mV
Output Voltage High
RL = 10kΩ to ground
RL = 2kΩ to ground
RL = 10kΩ to ground
RL = 2kΩ to ground
13.5
13.65
-
-
V
V
13.2
-
13.4
13.5
-
V
13.1
-
-
V
VOL
Output Voltage Low
-
-13.65
-13.5
-13.2
-13.4
-13.1
2.8
3.7
-
V
-
-
-13.5
-
V
-
V
-
V
IS
Supply Current/Amplifier
-
2.2
-
mA
mA
mA
V
-
-
ISC
Short-Circuit
RL = 0Ω to ground
±45
-
VSUPPLY
Supply Voltage Range
Guaranteed by PSRR
±2.25
±20
AC SPECIFICATIONS
GBW
enp-p
en
Gain Bandwidth Product
10
85
MHz
nVP-P
Voltage Noise
0.1Hz to 10Hz
f = 10Hz
Voltage Noise Density
Voltage Noise Density
Voltage Noise Density
Voltage Noise Density
Current Noise Density
3
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
pA/√Hz
%
en
f = 100Hz
f = 1kHz
2.8
en
2.5
en
f = 10kHz
f = 10kHz
2.5
in
0.4
THD + N
Total Harmonic Distortion +
Noise
1kHz, G = 1, VO = 3.5VRMS
RL = 2kΩ
,
0.00022
TRANSIENT RESPONSE
SR
Slew Rate
AV = 10, RL = 2kΩ, VO = 4VP-P
AV = -1, VOUT = 100mVP-P
±3.6
36
V/µs
ns
tr, tf, Small
Signal
Rise Time
10% to 90% of VOUT
,
Rf = Rg = 2kΩ, RL = 2kΩ to VCM
AV = -1, VOUT = 100mVP-P
Rf = Rg = 2kΩ, RL = 2kΩ to VCM
AV = -1 VOUT = 10VP-P
Rg = Rf =10k, RL = 2kΩ to VCM
AV = -1, VOUT = 10VP-P
L = 2kΩ to VCM
Fall Time
90% to 10% of VOUT
,
38
3.4
3.8
1.7
ns
µs
µs
µs
ts
Settling Time to 0.1%
10V Step; 10% to VOUT
,
Settling Time to 0.01%
10V Step; 10% to VOUT
,
R
tOL
Output Overload Recovery Time AV = 100, VIN = 0.2V
RL = 2kΩ to VCM
FN6633.3
March 18, 2010
5
ISL28127, ISL28227
Electrical Specifications VS ±5V, VCM = 0, VO = 0V, TA = +25°C, unless otherwise noted. Boldface limits apply over
the operating temperature range, -40°C to +125°C. Temperature data established
by characterization.
MIN
MAX
PARAMETER
DESCRIPTION
Offset Voltage
CONDITIONS
(Note 8)
TYP
10
-
(Note 8)
UNIT
µV
VOS
-70
70
-120
120
µV
V
OS/T
Offset Voltage Drift
Input Offset Current
-0.5
-10
-12
10
0.1
1
-
0.5
10
12
10
12
3
µV/°C
nA
nA
nA
nA
V
IOS
IB
1
-
Input Bias Current
-12
-3
VCM
Common Mode Input Voltage
Range
Guaranteed by CMRR
-
-2
-
2
V
CMRR
PSRR
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
V
CM = -3V to +3V
115
120
-
-
dB
dB
VCM = -2V to +2V
115
-
VS = ±2.25V to ±5V
115
125
-
-
-
dB
dB
VS = ±3V to ±5V
115
AVOL
VOH
Open-Loop Gain
VO = -3V to +3V
RL = 10kΩ to ground
1000
1500
-
V/mV
Output Voltage High
RL = 10kΩ to ground
RL = 2kΩ to ground
RL = 10kΩ to ground
RL = 2kΩ to ground
3.5
3.65
-
-
V
V
3.2
-
3.5
-
3.4
-
3.1
-
V
V
V
VOL
Output Voltage Low
-
-
-
-
-
-
-
-3.65
-
-3.5
-3.2
-3.4
-3.1
2.8
3.7
-
-3.5
-
V
IS
Supply Current/Amplifier
Short-Circuit
2.2
-
mA
mA
mA
ISC
± 45
AC SPECIFICATIONS
GBW
Gain Bandwidth Product
10
MHz
%
THD + N
Total Harmonic Distortion +
Noise
1kHz, G = 1, Vo = 2.5VRMS
RL = 2kΩ
,
0.0034
TRANSIENT RESPONSE
SR
Slew Rate
AV = 10, RL = 2kΩOH
±3.6
36
V/µs
ns
tr, tf, Small
Signal
Rise Time
10% to 90% of VOUT
AV = -1, VOUT = 100mVP-P
Rf = Rg = 2kΩ, RL = 2kΩ to VCM
,
Fall Time
90% to 10% of VOUT
AV = -1, VOUT = 100mVP-P
Rf = Rg = 2kΩ, RL = 2kΩ to VCM
,
38
1.6
4.2
ns
µs
µs
ts
Settling Time to 0.1%
AV = -1, VOUT = 4VP-P
,
Rf = Rg = 2kΩ, RL = 2kΩ to VCM
Settling Time to 0.01%
AV = -1, VOUT = 4VP-P
,
Rf = Rg = 2kΩ, RL = 2kΩ to VCM
NOTE:
8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established
by characterization and are not production tested.
FN6633.3
March 18, 2010
6
ISL28127, ISL28227
Typical Performance Curves VS = ±15V, VCM = 0V, RL = Open, unless otherwise
specified.
100
100
80
VS = ±19V
60
40
AV = 1
20
0
10
-20
-40
-60
-80
-100
V
= 38V
+
L
R = 10k
C = 3.5pF
L
R = 10, R = 100k
g
V
f
A
= 10,000
1
0.1
0
1
2
3
4
5
6
7
8
9
10
1
10
100
1k
10k
100k
TIME (s)
FREQUENCY (Hz)
FIGURE 1. INPUT NOISE VOLTAGE 0.1Hz to 10Hz
FIGURE 2. INPUT NOISE VOLTAGE SPECTRAL
DENSITY
130
120
110
100
90
100
PSRR+ and PSRR- V = ±5V
VS = ±19V
AV = 1
S
R = INF
L
10
1
80
70
60
50
C = 5.25pF
L
A
= +1
V
S
V
= 1V
P-P
40 PSRR+ and PSRR- V = ±15V
S
30
20
10
0
-10
0.1
10M
10
100
1k
10k
100k
1M
0.1
1
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 4. PSRR vs FREQUENCY, VS = ±5V, ±15V
FIGURE 3. INPUT NOISE CURRENT SPECTRAL
DENSITY
25
20
130
120
110
100
90
80
70
60
50
VS = ±5V
MEDIAN
VS = ±2.25V
15
VS = ±21V
10
5
VS = ±15V
VS = ±15V
0
40
30
20
10
-5
RL = INF
VS = ±3V
CL = 5.25pF
-10
VS = ±5V
AV = +1
-15
VCM = 1VP-P
0
36 UNITS
-20
-10
-40 -20
0
20 40 60 80 100 120 140 160
TEMPERATURE (°C)
10M
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FIGURE 5. CMRR vs FREQUENCY, VS = ±2.25, ±5V,
±15V
FIGURE 6. VOS vs TEMPERATURE vs VSUPPLY
FN6633.3
March 18, 2010
7
ISL28127, ISL28227
Typical Performance Curves VS = ±15V, VCM = 0V, RL = Open, unless otherwise
specified. (Continued)
3.0
4.5
50 UNITS
50 UNITS
MEDIAN
IBIAS
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
2.5
2.0
1.5
1.0
0.5
0
MEDIAN
-
IBIAS+
IBIAS
+
IBIAS
-
-40
-20
0
20
40
60
80
100 120
-40
-20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 7. IIB vs TEMPERATURE, VS = ±15V
FIGURE 8. IIB vs TEMPERATURE, VS = ±5V
60
0.5
29 UNITS
vs = ±5
0.0
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
-3.5
AVERAGE
40
50 UNITS
20
+25°C
vs = ±15
0
+125°C
MEDIAN
-20
-40°C
-40
-60
-15
-10
-5
0
5
10
15
-40
-20
0
20
40
60
80
100 120
INPUT COMMON MODE VOLTAGE
TEMPERATURE (°C)
FIGURE 10. INPUT OFFSET VOLTAGE vs INPUT
COMMON MODE VOLTAGE, VS = ±15V
FIGURE 9. IOS vs TEMPERATURE vs SUPPLY
-13.1
14.2
50 UNITS
-13.2
-13.3
-13.4
-13.5
-13.6
-13.7
-13.8
-13.9
-14.0
-14.1
-14.2
MEDIAN
RL = 2k
14.1
14.0
13.9
13.8
13.7
13.6
13.5
13.4
13.3
13.2
50 UNITS
MEDIAN
RL = 100k
RL = 100k
RL = 2k
-40
-20
0
20
40
60
80
100 120
-40
-20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 12. VOL vs TEMPERATURE, VS = ±15V
FIGURE 11. VOH vs TEMPERATURE, VS = ±15V
FN6633.3
March 18, 2010
8
ISL28127, ISL28227
Typical Performance Curves VS = ±15V, VCM = 0V, RL = Open, unless otherwise
specified. (Continued)
200
180
160
140
120
100
80
200
180
160
140
120
100
80
PHASE
PHASE
60
60
40
20
40
20
GAIN
GAIN
0
0
-20
-40
-60
-80
-100
-20
-40
-60
-80
-100
RL = 10k
RL = 10k
CL = 100pF
SIMULATION
CL = 10pF
SIMULATION
0.1m1m 10m100m 1 10 100 1k 10k100k1M10M100M
FREQUENCY (Hz)
0.1m1m 10m100m 1 10 100 1k 10k100k1M10M100M
FREQUENCY (Hz)
FIGURE 14. OPEN-LOOP GAIN, PHASE vs
FIGURE 13. OPEN-LOOP GAIN, PHASE vs
FREQUENCY, RL = 10kΩ, CL = 100pF
FREQUENCY, RL = 10kΩ, CL = 10pF
70
15
Rf = Rg = 100k
AV = 1000
AV = 100
Rg = 100, Rf = 100k
Rg = 1k, Rf = 100k
13
60
50
40
30
20
10
0
Rf = Rg = 10k
11
Rf = Rg = 1k
9
VS = ±15V
CL = 3.5pF
RL = INF
7
5
VOUT = 100mVP-P
AV = 10
3
1
VS = ±15V
L = 10k
Rf = Rg = 100
R
Rg = 10k, Rf = 100k
AV = 1
CL = 3.5pF
-1
-3
-5
AV = +2
VOUT = 100mVP-P
Rg = OPEN, Rf = 0
1k
10k
-10
100
100k
1M
10M
100M
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 15. FREQUENCY RESPONSE vs CLOSED LOOP
GAIN
FIGURE 16. FREQUENCY RESPONSE vs FEEDBACK
RESISTANCE Rf/Rg
2
7
RL = 10k
VS = ±15V
6
1
RL = 10k
5
RL = 1k
AV = +1
CL = 1000pF
CL = 220pF
0
VOUT = 100mVP-P
4
3
-1
RL = 499
CL = 100pF
CL = 25.5pF
2
-2
-3
-4
-5
RL = 100
RL = 49.9
1
VS = ±15V
CL = 3.5pF
0
-1
-2
-3
AV = +1
CL = 3.5pF
VOUT = 100mVP-P
1k
10k
100k
1M
10M
100M
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 18. GAIN vs FREQUENCY vs CL
FIGURE 17. GAIN vs FREQUENCY vs RL
FN6633.3
March 18, 2010
9
ISL28127, ISL28227
Typical Performance Curves VS = ±15V, VCM = 0V, RL = Open, unless otherwise
specified. (Continued)
1
6
5
VS = ±2.25V
4
VS = ±15V
CL = 3.5pF
AV = 1
0
-1
-2
-3
3
2
Rf = 0 Rg = inf
1
VS = ±5V
VS = ±15V
VOUT = 10VP-P
0
1
CL = 3.5pF
-2
-3
-4
-5
-6
RL = 2k
RL = 10k
RL = 10k
AV = +1
VOUT = 100mVP-P
1k
10k
100k
FREQUENCY (Hz)
1M
10M
100M
0
5
10
15
20
25
30
TIME (µs)
FIGURE 20. LARGE SIGNAL 10V STEP RESPONSE,
VS = ±15V
FIGURE 19. GAIN vs FREQUENCY vs SUPPLY
VOLTAGE
2.4
2.0
1.6
80
60
40
1.2
VS = ±15V, RL = 2k, 10k
0.8
0.4
0
20
0
VS = ±5V, ±15V
-0.4
VS = ±5V, RL = 2k, 10k
20
40
60
80
-0.8
RL = 2k
CL = 3.5pF
AV = 1
-1.2
CL = 3.5pF
AV = 1
VOUT = 4VP-P
-1.6
VOUT = 100mVP-P
-2.0
-2.4
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
TIME (ms)
0
5
10
15
20
25
30
35
40
TIME (µs)
FIGURE 21. LARGE SIGNAL TRANSIENT RESPONSE vs
RL VS = ±5V, ±15V
FIGURE 22. SMALL SIGNAL TRANSIENT RESPONSE,
VS = ±5V, ±15V
0.26
0.22
0.08
0.04
0.10
0.06
0.02
-0.02
-0.06
2
0.06
0.02
15
13
11
9
OUTPUT
0
-2
INPUT
-0.02
-0.06
-0.10
-0.14
-0.18
-0.20
-0.26
VS = ±15V
RL = 10k
CL = 3.5pF
V = 100
Rf = 100k, Rg = 1k
VIN = 200mVP-P
-4
VS = ±15V
L = 10k
L = 3.5pF
V = 100
Rf = 100k, Rg = 1k
IN = 200mVP-P
R
C
A
A
-6
7
-8
5
V
-10
-12
INPUT
3
1
OUTPUT
25
-14
40
-1
0
5
10
15
20
25
30
35
0
5
10
15
20
30
35
40
TIME (µs)
TIME (µs)
FIGURE 24. NEGATIVE OUTPUT OVERLOAD
RESPONSE TIME, VS = ±15V
FIGURE 23. POSITIVE OUTPUT OVERLOAD
RESPONSE TIME, VS = ±15V
FN6633.3
March 18, 2010
10
ISL28127, ISL28227
Typical Performance Curves VS = ±15V, VCM = 0V, RL = Open, unless otherwise
specified. (Continued)
90
80
VS = ±15V
RL = 10k
70
60
50
40
30
20
10
0
AV = 1
VOUT = 100mVP-P
10
100
1000
10000
CAPACITANCE (pF)
FIGURE 25. % OVERSHOOT vs LOAD CAPACITANCE, VS = ±15V
For unity gain applications (see Figure 26) where the
Applications Information
Functional Description
output is connected directly to the non-inverting input a
current limiting resistor (RIN) will be needed under the
following conditions to protect the anti-parallel
differential input protection diodes.
The ISL28127 and ISL28227 are single and dual, low
noise 10MHz BW precision op amps. Both devices are
fabricated in a new precision 40V complementary bipolar
DI process. A super-beta NPN input stage with input bias
current cancellation provides low input bias current (1nA
typical), low input offset voltage (10µV typ), low input
noise voltage (3nV/√Hz), and low 1/f noise corner
frequency (5Hz). These amplifiers also feature high open
loop gain (1500V/mV) for excellent CMRR (120dB) and
THD+N performance (0.0002% @ 3.5VRMS, 1kHz into
2kΩ). A complimentary bipolar output stage enables high
capacitive load drive without external compensation.
• The amplifier input is supplied from a low impedance
source.
• The input voltage rate-of-rise (dV/dt) exceeds the
maximum slew rate of the amplifier (±3.6V/µs).
If the output lags far enough behind the input, the
anti-parallel input diodes can conduct. For example, if
an input pulse ramps from 0V to +10V in 1µs, then the
output of the ISL28x27 will reach only +3.6V (slew
rate = 3.6V/µs) while the input is at 10V, The input
differential voltage of 6.4V will force input ESD diodes to
conduct, dumping the input current directly into the
output stage and the load. The resulting current flow
can cause permanent damage to the ESD diodes. The
ESD diodes are rated to 20mA, and in the previous
example, setting RIN to 1k resistor (see Figure 26)
would limit the current to < 6.4mA, and provide
additional protection up to ±20V at the input.
Operating Voltage Range
The devices are designed to operate over the 4.5V
(±2.25V) to 40V (±20V) range and are fully
characterized at 10V (±5V) and 30V (±15V). Parameter
variation with operating voltage is shown in the “Typical
Performance Curves” beginning on page 7.
Input ESD Diode Protection
In applications where one or both amplifier input
terminals are at risk of exposure to high voltage, current
limiting resistors may be needed at each input terminal
(see Figure 27 RIN+, RIN-) to limit current through the
power supply ESD diodes to 20mA.
The input terminals (IN+ and IN-) have internal ESD
protection diodes to the positive and negative supply
rails, and an additional anti-parallel diode pair across
the inputs (see Figures 26 and 27).
V+
V+
R
-
IN
-
-
V
V
-
IN
V
OUT
OUT
R
R
IN
+
IN
+
V
R
V
+
IN
R
L
IN
L
V-
V-
FIGURE 26. INPUT ESD DIODE CURRENT LIMITING-
UNITY GAIN
FIGURE 27. INPUT ESD DIODE CURRENT LIMITING -
DIFFERENTIAL INPUT
FN6633.3
March 18, 2010
11
ISL28127, ISL28227
Output Current Limiting
ISL28127 and ISL28227 SPICE Model
The output current is internally limited to approximately
±45mA at +25°C and can withstand an short circuit to
either rail as long as the power dissipation limits are not
exceeded. This applies to only 1 amplifier at a time for
the dual op amp. Continuous operation under these
conditions may degrade long term reliability.
Figure 28 shows the SPICE model schematic and
Figure 29 shows the net list for the ISL28127 and
ISL28227 SPICE model. The model is a simplified
version of the actual device and simulates important AC
and DC parameters. AC parameters incorporated into
the model are: 1/f and flatband noise, Slew Rate,
CMRR, Gain and Phase. The DC parameters are VOS,
IOS, total supply current and output voltage swing. The
model does not model input bias current. The model
uses typical parameters given in the “Electrical
Specifications” Table beginning on page 4. The AVOL is
adjusted for 128dB with the dominate pole at 5Hz. The
CMRR is set higher than the “Electrical Specifications”
Table to better match design simulations (150dB,
f = 50Hz). The input stage models the actual device to
present an accurate AC representation. The model is
configured for ambient temperature of +25°C.
Output Phase Reversal
Output phase reversal is a change of polarity in the
amplifier transfer function when the input voltage
exceeds the supply voltage. The ISL28127 and ISL28227
are immune to output phase reversal, even when the
input voltage is 1V beyond the supplies.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power supply
conditions. It is therefore important to calculate the
maximum junction temperature (TJMAX) for all
applications to determine if power supply voltages, load
conditions, or package type need to be modified to
remain in the safe operating area. These parameters are
related using Equation 1:
Figures 30 through 45 show the characterization vs
simulation results for the Noise Voltage, Closed Loop
Gain vs Frequency, Closed Loop Gain vs Rf/Rg, Closed
Loop Gain vs RL, Closed Loop Gain vs CL, Large Signal
10V Step Response, Open Loop Gain Phase and
Simulated CMRR vs Frequency.
(EQ. 1)
T
= T
+ θ xPD
MAX JA MAXTOTAL
JMAX
LICENSE STATEMENT
The information in this SPICE model is protected under
the United States copyright laws. Intersil Corporation
hereby grants users of this macro-model hereto referred
to as “Licensee”, a nonexclusive, nontransferable licence
to use this model as long as the Licensee abides by the
terms of this agreement. Before using this macro-model,
the Licensee should read this license. If the Licensee
does not accept these terms, permission to use the
model is not granted.
where:
• PDMAXTOTAL is the sum of the maximum power
dissipation of each amplifier in the package (PDMAX
)
• PDMAX for each amplifier can be calculated using
Equation 2:
V
OUTMAX
R
L
----------------------------
PD
= V × I
+ (V - V ) ×
OUTMAX
MAX
S
qMAX
S
(EQ.2)
The Licensee may not sell, loan, rent, or license the
macro-model, in whole, in part, or in modified form, to
anyone outside the Licensee’s company. The Licensee
may modify the macro-model to suit his/her specific
applications, and the Licensee may make copies of this
macro-model for use within their company only.
where:
• TMAX = Maximum ambient temperature
• θJA = Thermal resistance of the package
• PDMAX = Maximum power dissipation of 1 amplifier
• VS = Total supply voltage
This macro-model is provided “AS IS, WHERE IS, AND
WITH NO WARRANTY OF ANY KIND EITHER EXPRESSED
OR IMPLIED, INCLUDING BUY NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.”
• IqMAX = Maximum quiescent supply current of 1
amplifier
• VOUTMAX = Maximum output voltage swing of the
application
In no event will Intersil be liable for special, collateral,
incidental, or consequential damages in connection with
or arising out of the use of this macro-model. Intersil
reserves the right to make changes to the product and
the macro-model without prior notice.
RL = Load resistance
FN6633.3
March 18, 2010
12
ISL28127, ISL28227
.
V++
V++
R3
R4
IEE1
4
5
96E-6
4.45k
4.45k
4
5
CASCODE
CASCODE
6
7
Q4
Q5
3
D1
DX
C4
2
2.5pF
SUPERB
SUPERB
Vin-
V5
V
-
Q1 Q2
IN
C5
2.5pF
R1
8
5E11
24
25
EOS
C6
2pF
1
IOS
Mirror
Vc
D12
DN
0.1V
R17
VCM
+
-
+
Vmid
Q3
-
1E-9
9
IEE
R2
200E-6
377.4
In+
+
VOS
5E11
En
10E-6
-
V
+
IN
V--
VCM
Voltage Noise
Input Stage
V++
V++
D2
DX
D4
DX
G1
G3
G5
L1
13
10
4
3.18E-3
+
+
+
-
+
-
+
-
R5
1
R7
C2
R9
1
V1
V3
17
55.55pF
R11
1
1.86V
1.86V
572.9E6
-
-
5
11
Vc
Vg
Vmid
Vg
Vc
R12
1
R6
1
R8
R10
1
C3
Vmid
G4
G6
G2
572.9E6
55.55pF
18
+
-
+
-
-
+
-
+
-
+
V4
V2
L2
1.86V
1.86V
12
14
VCM
3.18E-3
D5
DX
D3
DX
V--
V--
VCM
ST Gain Stage
2nd Gain Stage
Mid Supply Ref
Common Mode Gain Stage
1
V++
D8
DX
D9
DX
G7
V+
V+
+
-
+
E2
R15
90
-
-
+
22
23
V5
DX
DX
D6
D7
20
21
ISY
V
OUT
VOUT
1.12V
2.2mA
Vg
V6
1.12V
R16
90
V-
G8
-
+
+
-
+
-
-
+
D10
DY
D11
DY
-
E3
V-
+
V--
G9
G10
Supply Isolation Stage
Output Stage
FIGURE 28. SPICE SCHEMATIC
FN6633.3
March 18, 2010
13
ISL28127, ISL28227
* source ISL28127_SPICEmodel
R_R7
VG V++ 572.958E6 TC=0,0
V-- VG 572.958E6 TC=0,0
VG V++ 55.55e-12 TC=0,0
V-- VG 55.55e-12 TC=0,0
13 V++ DX
* Revision C, August 8th 2009 LaFontaine
* Model for Noise, supply currents, 150dB f=50Hz
CMRR, *128dB f=5Hz AOL
R_R8
C_C2
C_C3
D_D4
D_D5
V_V3
V_V4
*
*Copyright 2009 by Intersil Corporation
*Refer to data sheet “LICENSE STATEMENT” Use of
*this model indicates your acceptance with the
*terms and provisions in the License Statement.
* Connections: +input
V-- 14 DX
13 VG 1.86
VG 14 1.86
*
*
*
*
*
|
|
|
|
|
-input
*Mid supply Ref
|
|
|
|
+Vsupply
R_R9
R_R10
I_ISY
E_E2
E_E3
*
VMID V++ 1 TC=0,0
V-- VMID 1 TC=0,0
V+ V- DC 2.2E-3
|
|
|
-Vsupply
|
|
output
|
V++ 0 V+ 0 1
V-- 0 V- 0 1
.subckt ISL28127subckt Vin+ Vin-V+ V- VOUT
* source ISL28127_SPICEMODEL_0_0
*
*Common Mode Gain Stage with Zero
*Voltage Noise
G_G5
G_G6
R_R11
R_R12
L_L1
L_L2
*
V++ VC VCM VMID 31.6228e-9
V-- VC VCM VMID 31.6228e-9
VC 17 1 TC=0,0
E_En
IN+ VIN+ 25 0 1
25 0 377.4 TC=0,0
24 25 DN
R_R17
D_D12
V_V7
18 VC 1 TC=0,0
24 0 0.1
17 V++ 3.183e-3
*
18 V-- 3.183e-3
*Input Stage
I_IOS
C_C6
IN+ VIN- DC 1e-9
IN+ VIN- 2E-12
*Output Stage with Correction Current Sources
G_G7
G_G8
G_G9
G_G10
D_D6
D_D7
D_D8
D_D9
D_D10
D_D11
V_V5
V_V6
R_R15
R_R16
*
VOUT V++ V++ VG 1.11e-2
V-- VOUT VG V-- 1.11e-2
22 V-- VOUT VG 1.11e-2
23 V-- VG VOUT 1.11e-2
VG 20 DX
R_R1
VCM VIN- 5e11 TC=0,0
IN+ VCM 5e11 TC=0,0
2 VIN- 1 SuperB
3 8 1 SuperB
R_R2
Q_Q1
Q_Q2
Q_Q3
V-- 1 7 Mirror
21 VG DX
Q_Q4
4 6 2 Cascode
V++ 22 DX
Q_Q5
5 6 3 Cascode
V++ 23 DX
R_R3
4 V++ 4.45e3 TC=0,0
5 V++ 4.45e3 TC=0,0
V-- 22 DY
R_R4
V-- 23 DY
C_C4 VIN- 0 2.5e-12
C_C5 8 0 2.5e-12
20 VOUT 1.12
VOUT 21 1.12
D_D1
I_IEE
I_IEE1
V_VOS
E_EOS
*
6 7 DX
VOUT V++ 9E1 TC=0,0
V-- VOUT 9E1 TC=0,0
1 V-- DC 200e-6
V++ 6 DC 96e-6
9 IN+ 10e-6
8 9 VC VMID 1
.model SuperB npn
+ is=184E-15 bf=30e3 va=15 ik=70E-3 rb=50
+ re=0.065 rc=35 cje=1.5E-12 cjc=2E-12
+ kf=0 af=0
*1st Gain Stage
G_G1
G_G2
R_R5
R_R6
D_D2
D_D3
V_V1
V_V2
*
V++ 11 4 5 0.0487707
.model Cascode npn
V-- 11 4 5 0.0487707
11 V++ 1 TC=0,0
V-- 11 1 TC=0,0
10 V++ DX
+ is=502E-18 bf=150 va=300 ik=17E-3 rb=140
+ re=0.011 rc=900 cje=0.2E-12 cjc=0.16E-12f
+ kf=0 af=0
.model Mirror pnp
V-- 12 DX
+ is=4E-15 bf=150 va=50 ik=138E-3 rb=185
+ re=0.101 rc=180 cje=1.34E-12 cjc=0.44E-12
+ kf=0 af=0
10 11 1.86
11 12 1.86
.model DN D(KF=6.69e-9 AF=1)
.MODEL DX D(IS=1E-12 Rs=0.1)
*2nd Gain Stage
G_G3
G_G4
V++ VG 11 VMID 4.60767E-3
.MODEL DY D(IS=1E-15 BV=50 Rs=1)
.ends ISL28127subckt
V-- VG 11 VMID 4.60767E-3
FIGURE 29. SPICE NET LIST
FN6633.3
March 18, 2010
14
ISL28127, ISL28227
Characterization vs Simulation Results
100
10
1
100
10
1
V
= ±19V
= 1
S
A
V
V(INOISE)
1
0.1
10
100
1k
10k
100k
0.1
1
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 31. SIMULATED INPUT NOISE VOLTAGE
FIGURE 30. CHARACTERIZED INPUT NOISE VOLTAGE
70
70
A
= 1000
= 100
= 10
R
= 100, R = 100k
f
A
= 1000
= 100
= 10
R
= 100, R = 100k
f
V
g
V
g
60
50
40
30
20
10
0
60
50
40
30
20
10
0
R
= 1k, R = 100k
f
R
= 1k, R = 100k
f
g
g
A
A
V
V
V
= ±15V
= 3.5pF
= INF
S
L
C
R
L
V
= 100mV
OUT
P-P
A
A
V
V
R
= 10k, R = 100k
f
R
= 10k, R = 100k
f
g
g
A
= 1
A
= 1
V
V
R
= OPEN, R = 0
f
R
= OPEN, R = 0
f
g
g
-10
-10
10k
FREQUENCY (Hz)
100
1k
100k
1M
10M
100M
10k
FREQUENCY (Hz)
100
1k
100k
1M
10M
100M
FIGURE 32. CHARACTERIZED CLOSED LOOP GAIN vs
FREQUENCY
FIGURE 33. SIMULATED CLOSED LOOP GAIN vs
FREQUENCY
15
15
R = R = 100k
R = R = 100k
f
g
f
g
13
11
9
13
11
9
R = R = 10k
f
g
R = R = 10k
f
g
7
R = R = 1k
7
f
g
R = R = 1k
f
g
5
5
3
V
= ±15V
= 10k
3
V
= ±15V
= 10k
S
R = R = 100
S
R = R = 100
f
g
f
g
R
C
A
R
C
A
L
L
L
L
1
1
= 3.5pF
= +2
= 3.5pF
= +2
-1
-3
-5
-1
-3
-5
V
V
V
= 100mV
V
= 100mV
OUT
P-P
OUT
P-P
1k
10k
100k
1M
10M
100M
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 35. SIMULATED CLOSED LOOP GAIN vs Rf/Rg
FIGURE 34. CHARACTERIZED CLOSED LOOP GAIN vs
Rf/Rg
FN6633.3
March 18, 2010
15
ISL28127, ISL28227
Characterization vs Simulation Results (Continued)
2
2
R
R
= 10k
= 1k
L
L
1
1
R
= 10k
L
0
0
R
= 1k
L
-1
-2
-3
-4
-5
-1
-2
-3
-4
-5
R
R
= 499
= 100
L
R
= 499
L
L
R
= 100
L
V
= ±15V
= 3.5pF
= +1
V
= ±15V
= 3.5pF
= +1
S
S
R
= 49.9
L
C
A
C
A
L
L
V
V
R
= 49.9
L
V
= 100mV
V
= 100mV
OUT
P-P
OUT
P-P
1k
10k
100k
1M
10M
100M
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 36. CHARACTERIZED CLOSED LOOP GAIN vs
RL
FIGURE 37. SIMULATED CLOSED LOOP GAIN vs RL
7
7
V
R
A
V
= ±15V
= 10k
= +1
V
R
= ±15V
= 10k
= +1
S
6
5
S
6
5
C
= 1000pF
L
L
L
C
= 1000pF
A
V
L
V
= 100mV
P-P
4
OUT
V
= 100mV
4
OUT P-P
C
= 220pF
L
3
3
C
= 100pF
L
2
2
C
= 220pF
= 100pF
L
C
= 25.5pF
1
L
1
0
C
0
L
C
= 25.5pF
L
-1
-2
-3
-1
-2
-3
C
= 3.5pF
L
C
= 3.5pF
1M
L
1k
10k
100k
1M
10M
100M
1k
10k
100k
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 38. CHARACTERIZED CLOSED LOOP GAIN vs
CL
FIGURE 39. SIMULATED CLOSED LOOP GAIN vs CL
6
5
4
6
5
4
V
= ±15V
= 3.5pF
= 1
S
L
3
2
V
C
= ±15V
= 3.5pF
= 1
S
3
2
C
A
L
V
A
V
R = 0, R = INF
1
f
g
R = 0, R = INF
1
f
g
V
= 10V
OUT
P-P
V
= 10V
0
OUT
P-P
0
1
1
-2
-3
-4
-5
-6
R
= 10k
L
-2
-3
-4
-5
-6
R
= 2k
L
R
= 10k
L
0
5
10
15
TIME (µs)
20
25
30
0
5
10
15
TIME (µs)
20
25
30
FIGURE 41. SIMULATED LARGE SIGNAL 10V STEP
RESPONSE
FIGURE 40. CHARACTERIZED LARGE SIGNAL 10V
STEP RESPONSE
FN6633.3
March 18, 2010
16
ISL28127, ISL28227
Characterization vs Simulation Results (Continued)
200
150
100
50
200
180
160
140
120
100
80
60
40
20
0
PHASE
PHASE
GAIN
GAIN
0
R
C
= 10k
= 10pF
-20
-40
-60
-80
-100
L
L
R
C
= 10k
L
L
-50
= 10pF
Model V set to zero
for this test
OS
SIMULATION
-100
0.1Hz
10Hz
1.0k
100k
10M
0.1m 1m 10m100m
1
10 100 1k 10k 100k 1M 10M100M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 43. SIMULATED OPEN-LOOP GAIN, PHASE vs
FREQUENCY
FIGURE 42. SIMULATED OPEN-LOOP GAIN, PHASE vs
FREQUENCY
150
100
50
130
V
= ±5V
S
120
110
100
90
80
70
60
50
40
30
20
10
0
V
= ±2.25V
S
V
= ±15V
S
R
C
A
= INF
L
L
Generated using full
model. CMRR delta input
0
= 5.25pF
= +1
base voltage/V
V
CM
V
= 1V
input Voltage
-50
10m
CM
P-P
-10
10M
1.0Hz 100Hz 10k
1.0M
100M 10G 1.0T
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 44. CHARACTERIZED CMRR vs FREQUENCY
FIGURE 45. SIMULATED CMRR vs FREQUENCY
FN6633.3
March 18, 2010
17
ISL28127, ISL28227
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to
web to make sure you have the latest Rev.
REVISION
DATE
CHANGE
FN6633.3
3/11/10
PODs M8.118 and L8.3x3A - Updated to new intersil format by adding land pattern
and moving dimensions from table onto drawing.
3/3/10
Page 2:
Under "Ordering Information"
ISL28227FBZ: Changed Vos max from 80µV to 75µV
Page 4:
Changed:
1. ISL28227 SOIC Room Temp limit for Vos from 80µV (MAX) and -80µV (MIN) to
75µV (MAX) and -75µV (MIN).
2. ISL28227 SOIC Full Temp limit for Vos from 160µV (MAX) and -160µV (MIN) to
150µV (MAX) and -150µV (MIN)
3. ISL28227 SOIC limit for TCVos from 0.8µV (MAX) and -0.8µV (MIN) to 0.75µV
(MAX) and -0.75µV (MIN)
3/2/10
HBM for ISL28227 changed from “4kV” to “6kV”
Tjc values for ISL28227 changed:
For MSOP from “50” to “45”
For SOIC from “60” to “55”
2/25/10
On the ordering info (page 2):
Part Number
Part Marking
Vos (Max) (uV)
ISL28127FRTBZ
ISL28127FRTZ
ISL28127FUBZ
ISL28127FUZ
TBD instead of 70
-C 127Z instead of 127Z C
8127Z -C instead of 8127Z
TBD instead of 70
150 instead of 70
Removed "Coming Soon) for ISL28127FUZ package
ISL28227FBZ
Removed "Coming Soon) for ISL28227FBZ package
ISL28227FRTBZ
80 instead of 70
TBD instead of 70
150 instead of 70
ISL28227FRTZ
ISL28227FUZ
-C 227Z instead of 227Z C
8227Z -C instead of 8227Z
Added the following row of data
ISL28227FUBZ 8227Z
TBD
On the Electrical specifications on page 4 and page 6 the following changes were
made. The change applies to the same spec found on page 4 and page 6.
VOS Offset Voltage; SOIC Package, ISL28127: Added -70 to MIN across room
temp and -120 MIN across full temp
VOS Offset Voltage; SOIC Package, ISL28227: Added -80 to MIN across room
temp and -160 MIN across full temp
VOS Offset Voltage; MSOP and TDFN Package Grade C, ISL28127/ISL28227:
Added -150 to MIN across room temp and -250 MIN across full temp
TCVOS Offset Voltage Drift; SOIC Package, ISL28127: Added -0.5 to MIN across
full temp
TCVOS Offset Voltage Drift; SOIC Package, ISL28227: Added -0.8 to MIN across
full temp
TCVOS Offset Voltage Drift; MSOP and TDFN Package Grade C,
ISL28127/ISL28227: Added -1 to MIN across full temp
IOS Input Offset Current: Added -10 to MIN across room temp and -12 to MIN
across full temp
IB Input Bias Current :Added -10 to MIN across room temp and -12 to MIN across
full temp
2/19/10
Added differentiated part numbers for B-grade and C-grade for TDFN and MSOP.
Added ESD and latch-up information. Broke out Theta JA to list the single and dual
and added Theta JC.
FN6633.3
March 18, 2010
18
ISL28127, ISL28227
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to
web to make sure you have the latest Rev. (Continued)
REVISION
DATE
CHANGE
FN6633.2
1/29/10
Added license statement for P-Spice Model.
Updated Spice Schematic by adding capacitors
C4, C5 and C6
Updated Spice Net List as follows:
From:
Revision B, July 23 2009
To:
Revision C, August 8th 2009 LaFontaine
From:
source ISL28127_SPICEMODEL_7_9
To:
source ISL28127_SPICEMODEL_0_0
Added after I_IOS:
C_C6
IN+ VIN- 2E-12
Added after R_R4:
C_C4 VIN- 0 2.5e-12
C_C5 8 0 2.5e-12
From:
.ends ISL28127
To:
.ends ISL28127subckt
Replaced POD MDP0027 with M8.15E to match ASYD in Intrepid (no dimension
changes; the PODs are the same. The change was to update to the Intersil format,
moving dimensions from table onto drawing and adding land pattern)
FN6633.1
9/14/09
“Functional Description” on page 11. Corrected low 1/f noise corner frequency
from 3Hz to 5Hz to match “Input Noise Voltage Spectral Density” on page 1.
Corrected high open loop gain from 1400V/mV to 1500V/mV to match “Open-Loop
Gain” on page 5 spec table.
“Operating Voltage Range” on page 11. Removed following 2 sentences since
there are no graphs illustrating common mode voltage sensitivity vs temperature
or VOS as a function of supply voltage and temperature:
"The input common mode voltage sensitivity to temperature is shown in Figure 3
(±15V). Figure 20 shows VOS as a function of supply voltage and temperature
with the common mode voltage at 0V for split supply operation."
9/2/09
Added Theta JC in Thermal Information for TDFN package
7/21/09
Updated Features to show only key features and updated applications section.
Added Typical Application Circuit and performance graph, Updated Ordering
Information to match Intrepid and added POD's L8.3x3A and M8.118, also added
MSL level as part of new format. Added TDFN pinouts, updated pin descriptions to
include TDFN pinouts, Added Theta Ja in Thermal information for TDFN and MSOP
packages. Added Revision History and Products Text with device info links. Added
SPICE Model with referencing text and Net List.
FN6633.0
5/28/09
Techdocs Issued File Number FN6633. Initial release of Datasheet with file number
FN6633 making this a Rev 0.
FN6633.3
March 18, 2010
19
ISL28127, ISL28227
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The
Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones,
handheld products, and notebooks. Intersil's product families address power management and analog signal
processing functions. Go to www.intersil.com/products for a complete list of Intersil product families.
*For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device
information page on intersil.com: ISL28127, ISL28227
To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff
FITs are available from our website at http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications
at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by
Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any
patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6633.3
March 18, 2010
20
ISL28127, ISL28227
Package Outline Drawing
M8.15E
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 0, 08/09
4
4.90 ± 0.10
A
DETAIL "A"
0.22 ± 0.03
B
6.0 ± 0.20
3.90 ± 0.10
4
PIN NO.1
ID MARK
5
(0.35) x 45°
4° ± 4°
0.43 ± 0.076
1.27
0.25 M C A B
SIDE VIEW “B”
TOP VIEW
1.75 MAX
1.45 ± 0.1
0.25
GAUGE PLANE
C
SEATING PLANE
0.175 ± 0.075
SIDE VIEW “A
0.10 C
0.63 ±0.23
DETAIL "A"
(0.60)
(1.27)
NOTES:
(1.50)
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
(5.40)
4. Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
The pin #1 identifier may be either a mold or mark feature.
Reference to JEDEC MS-012.
5.
6.
TYPICAL RECOMMENDED LAND PATTERN
FN6633.3
March 18, 2010
21
ISL28127, ISL28227
Package Outline Drawing
L8.3x3A
8 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
Rev 4, 2/10
( 2.30)
( 1.95)
3.00
A
B
( 8X 0.50)
(1.50)
6
PIN 1
INDEX AREA
( 2.90 )
(4X)
0.15
PIN 1
TOP VIEW
(6x 0.65)
( 8 X 0.30)
TYPICAL RECOMMENDED LAND PATTERN
SEE DETAIL "X"
0.10 C
2X 1.950
C
6X 0.65
0.75 ±0.05
0.08 C
1
PIN #1
INDEX AREA
6
SIDE VIEW
1.50 ±0.10
5
8
C
0 . 2 REF
4
8X 0.30 ±0.05
0.10 M C A B
8X 0.30 ± 0.10
0 . 02 NOM.
0 . 05 MAX.
2.30 ±0.10
DETAIL "X"
BOTTOM VIEW
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to ASME Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.20mm from the terminal tip.
Tiebar shown (if present) is a non-functional feature.
5.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
Compliant to JEDEC MO-229 WEEC-2 except for the foot length.
7.
FN6633.3
March 18, 2010
22
ISL28127, ISL28227
Package Outline Drawing
M8.118
8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
Rev 3, 3/10
5
3.0±0.05
A
8
DETAIL "X"
D
1.10 MAX
SIDE VIEW 2
0.09 - 0.20
4.9±0.15
3.0±0.05
5
0.95 REF
PIN# 1 ID
1
2
B
0.65 BSC
GAUGE
PLANE
TOP VIEW
0.25
3°±3°
0.55 ± 0.15
DETAIL "X"
0.85±010
H
C
SEATING PLANE
0.25 - 0.036
0.10 C
0.10 ± 0.05
0.08
C A-B D
M
SIDE VIEW 1
(5.80)
NOTES:
1. Dimensions are in millimeters.
(4.40)
(3.00)
2. Dimensioning and tolerancing conform to JEDEC MO-187-AA
and AMSEY14.5m-1994.
3. Plastic or metal protrusions of 0.15mm max per side are not
included.
(0.65)
4. Plastic interlead protrusions of 0.15mm max per side are not
included.
(0.40)
(1.40)
5. Dimensions are measured at Datum Plane "H".
6. Dimensions in ( ) are for reference only.
TYPICAL RECOMMENDED LAND PATTERN
FN6633.3
March 18, 2010
23
相关型号:
ISL28130CBZ-T
IC OP-AMP, 46.8 uV OFFSET-MAX, 0.4 MHz BAND WIDTH, PDSO8, ROHS COMPLIANT, PLASTIC, MS-012, SOIC-8, Operational Amplifier
RENESAS
ISL28130CBZT
OP-AMP, 46.8uV OFFSET-MAX, 0.4MHz BAND WIDTH, PDSO8, ROHS COMPLIANT, PLASTIC, MS-012, SOIC-8
RENESAS
©2020 ICPDF网 联系我们和版权申明