ISL80020AIRZ-T [INTERSIL]
Negative current protection;
| 型号： | ISL80020AIRZ-T |
| 厂家： | 
Intersil |
| 描述： | Negative current protection |
| 文件： | 总16页 (文件大小：708K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DATASHEET
Compact Synchronous Buck Converters
ISL80020, ISL80020A, ISL80015, ISL80015A
The ISL80020, ISL80020A, ISL80015 and ISL80015A are highly
efficient, monolithic, synchronous step-down DC/DC converters
Features
• V range 2.7V to 5.5V
IN
that can deliver up to 2A of continuous output current from a 2.7V
to 5.5V input supply. They use peak current mode control
architecture to allow very low duty cycle operation. They operate
at either 1MHz or 2MHz switching frequency, thereby providing
superior transient response and allowing for the use of small
inductors. They have excellent stability.
• I
OUT
maximum is 1.5A or 2A (see Table 1 on page 2)
• Switching frequency is 1MHz or 2MHz (see Table 1 on page 2)
• Overcurrent and short circuit protection
• Over-temperature/thermal protection
• Negative current protection
The ISL80020, ISL80020A, ISL80015 and ISL80015A integrate
very low r
MOSFETs in order to maximize efficiency. In
DS(ON)
• Power-good and enable
addition, since the high-side MOSFET is a PMOS, the need for a
Boot capacitor is eliminated, thereby reducing external
component count. They can operate at 100% duty cycle
(at 1MHz).
• 100% duty cycle (1MHZ)
• Internal soft-start and soft-stop
• V undervoltage lockout and V
IN
overvoltage protection
OUT
The device is configured in PWM (pulse width modulation) for
fast transient response, which helps reduce the output noise
and RF interference.
• Up to 95% peak efficiency
Applications
• General purpose POL
These devices are offered in a space saving 8 pin 2mmx2mm
TDFN lead free package with exposed pad for improved thermal
performance. The complete converter occupies less than
• Industrial, instrumentation, and medical equipment
• Telecom and networking equipment
• Game console
2
64mm area.
Related Literature
UG026, “ISL800xxxDEMO1Z Demonstration Boards User
Guide”
100
90
ISL80015, ISL80020
L1
+1.8V/2A
+2.7V...+5.5V
1
2
3
4
8
7
6
VIN
PHASE
PGND
NC
VOUT
GND
VIN
C1
22µF
C2
22µF
GND
EN
80
C3
22pF
EN
PG
SGND
PG
2.5V
OUT
3.3V
1.5V
OUT
R1
200kΩ 1%
OUT
1.8V
OUT
70
60
50
40
5
EPAD
9
FB
0.6V
R2
100kΩ 1%
V
O
(EQ. 1)
------------
R
= R
– 1
0.0 0.2 0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
1
2
VFB
OUTPUT LOAD (A)
FIGURE 1. TYPICAL APPLICATION CIRCUIT CONFIGURATION
FIGURE 2. EFFICIENCY vs LOAD, f
= 2MHz, V = 5V, T = +25°C
IN
SW
A
June 5, 2015
FN6692.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2015. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1
ISL80020, ISL80020A, ISL80015, ISL80015A
TABLE 1. SUMMARY OF KEY DIFFERENCES
I
(MAX)
f
V
RANGE
(V)
V
OUT
RANGE
(V)
PACKAGE
SIZE
OUT
(A)
SW
IN
PART#
(MHz)
ISL80015
ISL80015A
ISL80020
ISL80020A
1.5
1.5
2
1
2
1
2
2.7 to 5.5
0.6 to 5.5
8 pin 2mmx2mm TDFN
2
NOTE: In this datasheet, the parts listed in the table are collectively called “device”.
TABLE 2. COMPONENT VALUE SELECTION TABLE
V
C1
C2
C3
L1
R1
R2
OUT
(V)
0.8
1.2
1.5
1.8
2.5
3.3
(µF)
(µF)
(pF)
(µH)
(kΩ)
(kΩ)
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
1.0~2.2
1.0~2.2
1.0~2.2
1.0~3.3
1.5~3.3
1.5~4.7
33
100
100
100
100
100
100
100
150
200
316
450
FN6692.3
June 5, 2015
Submit Document Feedback
2
ISL80020, ISL80020A, ISL80015, ISL80015A
Pin Configuration
ISL80020, ISL80020A, ISL80015, ISL80015A
(8 LD 2x2 TDFN)
TOP VIEW
VIN
EN
1
2
3
4
8
7
6
5
PHASE
PGND
NC
EPAD
(GND)
PIN 9
SGND
PG
FB
Pin Descriptions
PIN #
PIN NAME
PIN DESCRIPTION
1
VIN
The input supply for the power stage of the PWM regulator and the source for the internal linear regulator that provides
bias for the IC. Place a minimum of 10µF ceramic capacitance from VIN to GND and as close as possible to the IC for
decoupling.
2
EN
Device enable input. When the voltage on this pin rises above 1.4V, the device is enabled. The device is disabled when
the pin is pulled to ground. When the device is disabled, a 100Ω resistor discharges the output through the PHASE pin.
See Figure 3, “FUNCTIONAL BLOCK DIAGRAM” on page 4 for details.
3
4
SGND
PG
Connect pin 3 to EPAD
Power-good output is pulled to ground during the soft-start interval and also when the output voltage is below regulation
limits. There is an internal 5MΩ internal pull-up resistor on this pin.
5
FB
Feedback pin for the regulator. FB is the negative input to the voltage loop error amplifier. The output voltage is set by
an external resistor divider connected to FB. In addition, the power-good PWM regulator’s power-good and undervoltage
protection circuits use FB to monitor the output voltage.
6
7
8
NC
Connect NC pin to EPAD
PGND
PHASE
Power and analog ground connections. Connect directly to the board GROUND plane.
Power stage switching node for output voltage regulation. Connect to the output inductor. This pin is discharged by an
100Ω resistor when the device is disabled. See Figure 3, “FUNCTIONAL BLOCK DIAGRAM” on page 4 for details.
9
E PAD
The exposed pad must be connected to the PGND pin for proper electrical performance. Place as many vias as possible
under the pad connecting to the PGND plane for optimal thermal performance.
FN6692.3
June 5, 2015
Submit Document Feedback
3
ISL80020, ISL80020A, ISL80015, ISL80015A
Functional Block Diagram
27pF
SOFT-
SHUTDOWN
START
200kΩ
+
+
VIN
OSCILLATOR
EN
VREF
+
BANDGAP
EAMP
COMP
P
N
-
-
PWM
LOGIC
SHUTDOWN
PHASE
PGND
CONTROLLER
PROTECTION
HS DRIVER
3pF
+
FB
SLOPE
COMP
1.15*VREF
6kΩ
+
-
-
CSA
OV
+
+
OCP
-
-
0.85*VREF
VIN
5MΩ
+
UV
PG
1ms
DELAY
NEG CURRENT
SENSING
-
SCP
+
0.3V
100Ω
SHUTDOWN
FIGURE 3. FUNCTIONAL BLOCK DIAGRAM
FN6692.3
June 5, 2015
Submit Document Feedback
4
ISL80020, ISL80020A, ISL80015, ISL80015A
Ordering Information
PACKAGE
PART NUMBER
(Notes 1, 2, 3)
TAPE AND REEL
QUANTITY
PART
MARKING
TECHNICAL
SPECIFICATIONS
TEMP. RANGE
(°C)
Tape and Reel
(RoHS Compliant)
PKG.
DWG. #
ISL80020IRZ-T
ISL80020IRZ-T7A
ISL80020AIRZ-T
ISL80020AIRZ-T7A
ISL80015IRZ-T
1000
250
020
020
20A
20A
015
015
A15
A15
20F
20F
0AF
0AF
15F
15F
5AF
5AF
2A, 1MHz
2A, 1MHz
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
8 Ld TDFN
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
L8.2x2C
1000
250
2A, 2MHz
2A, 2MHz
1000
250
1.5A, 1MHz
1.5A, 1MHz
1.5A, 2MHz
1.5A, 2MHz
2A, 1MHz
ISL80015IRZ-T7A
ISL80015AIRZ-T
ISL80015AIRZ-T7A
ISL80020FRZ-T
ISL80020FRZ-T7A
ISL80020AFRZ-T
ISL80020AFRZ-T7A
ISL80015FRZ-T
ISL80015FRZ-T7A
ISL80015AFRZ-T
ISL80015AFRZ-T7A
NOTES:
1000
250
1000
250
2A, 1MHz
1000
250
2A, 2MHz
2A, 2MHz
1000
250
1.5A, 1MHz
1.5A, 1MHz
1.5A, 2MHz
1.5A, 2MHz
1000
250
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL80020, ISL80020A, ISL80015, ISL80015A. For more information on
MSL please see techbrief TB363.
FN6692.3
June 5, 2015
Submit Document Feedback
5
ISL80020, ISL80020A, ISL80015, ISL80015A
Absolute Maximum Ratings
Thermal Information
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V (DC) or 7V (20ms)
PHASE . . . . . . . . . . . . . . -1.5V (100ns)/-0.3V (DC) to 6V (DC) or 7V (20ms)
EN, PG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VIN + 0.3V
FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 2.7V
Junction Temperature Range at 0A . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
ESD Rating
Human Body Model (Tested per JESD22-JS-001). . . . . . . . . . . . . . . . 4kV
Machine Model (Tested per JESD22-A115C) . . . . . . . . . . . . . . . . . . 300V
Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . . 2kV
Latch-up (Tested per JESD78D, Class 2, Level A) . . . ± 100mA at +125°C
Thermal Resistance (Typical, Notes 4, 5)
2x2 TDFN Package . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Operating Junction Temperature Range . . . . . . . . . . . . . .-40°C to +125°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
(°C/W)
71
(°C/W)
7
JA
JC
Recommended Operating Conditions
VIN Supply Voltage Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Load Current Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A to 2A
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
JA
Brief TB379 for details.
5. For , the “case temp” location is the center of the exposed metal pad on the package underside.
JC
Electrical Specifications T = -40°C to +125°C, V = 2.7V to 5.5V, unless otherwise noted. Typical values are at T = +25°C. Boldface
A
IN
A
limits apply across the junction operating temperature range, -40°C to +125°C.
MIN
MAX
PARAMETER
INPUT SUPPLY
Undervoltage Lockout Threshold
SYMBOL
TEST CONDITIONS
(Note 6)
TYP
(Note 6)
UNITS
V
V
Rising, no load
Falling, no load
2.5
2.4
7
2.7
V
IN
UVLO
2.2
V
Quiescent Supply Current
I
f
f
= 1MHz, no load at the output
= 2MHz, no load at the output
= 5.5V, EN = low
15
22
10
mA
mA
µA
VIN
SW
10
1.2
SW
Shutdown Supply Current
OUTPUT REGULATION
Feedback Voltage
I
V
IN
SD
V
0.594
0.589
-350
0.600
0.606
0.606
350
V
V
FB
T = -40°C to +125°C
A
VFB Bias Current
Line Regulation
I
V
= 2.7V, T = -40°C to +125°C
50
nA
%/V
VFB
FB
IN
A
V
= V + 0.5V to 5.5V (nominal 3.6V)
-0.32
-0.05
0.28
O
T = -40°C to +125°C
A
Load Regulation
See (Note 7)
< -0.2
1
%/A
ms
Soft-start Ramp Time Cycle (Note 7)
PROTECTIONS
Positive Peak Current Limit
IPLIMIT
2A application (V = 3.6V)
IN
2.8
2.1
3.18
2.5
3.6
2.9
A
A
1.5A application (V = 3.6V)
IN
Thermal Shutdown
Temperature rising
Temperature falling
150
25
°C
°C
Thermal Shutdown Hysteresis (Note 7)
COMPENSATION
Error Amplifier Transconductance
(Note 7)
40
µA/V
Transresistance
RT
0.24
0.3
0.40
Ω
PHASE
P-channel MOSFET ON-resistance
N-channel MOSFET ON-resistance
V
V
= 5V, I = 200mA
117
86
mΩ
mΩ
IN
O
= 5V, I = 200mA
IN
O
FN6692.3
June 5, 2015
Submit Document Feedback
6
ISL80020, ISL80020A, ISL80015, ISL80015A
Electrical Specifications T = -40°C to +125°C, V = 2.7V to 5.5V, unless otherwise noted. Typical values are at T = +25°C. Boldface
A
IN
A
limits apply across the junction operating temperature range, -40°C to +125°C. (Continued)
MIN
MAX
PARAMETER
SYMBOL
TEST CONDITIONS
(Note 6)
TYP
(Note 6)
UNITS
OSCILLATOR
Nominal Switching Frequency
f
ISL80020, ISL80015
800
1000
2000
1200
2360
kHz
kHz
SW
ISL80020A, ISL80015A
1640
PG
Output Low Voltage
Delay Time (Rising Edge)
PGOOD Delay Time (Falling Edge)
PG Pin Leakage Current
OVP PG Rising Threshold
OVP PG Hysteresis
UVP PG Rising Threshold
UVP PG Hysteresis
EN LOGIC
1mA sinking current
0.3
2.5
V
ms
µs
µA
%
0.5
1
5
PG = V
0.01
115
2
0.1
IN
110
80
125
%
85
5
90
%
%
Logic Input Low
0.4
1
V
V
Logic Input High
1.4
Logic Input Leakage Current
NOTES:
I
Pulled up to 5.5V
0.1
µA
EN
6. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
7. Not tested in production. Characterized using evaluation board. Refer to Figures 8 through 11 load regulation diagrams. +105°C T represents near
A
worst case operating point.
FN6692.3
June 5, 2015
Submit Document Feedback
7
ISL80020, ISL80020A, ISL80015, ISL80015A
Typical Performance Curves
100
90
80
70
60
50
40
100
90
80
70
60
50
40
2.5V
OUT
2.5V
OUT
1.2V
OUT
1.2V
OUT
1.5V
1.5V
OUT
OUT
1.8V
1.8V
OUT
OUT
0.0 0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0 0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
OUTPUT LOAD (A)
OUTPUT LOAD (A)
FIGURE 5. EFFICIENCY vs LOAD, f
= 2MHz, V = 3.3V,
IN
FIGURE 4. EFFICIENCY vs LOAD, f
SW
= 1MHz, V = 3.3V,
IN
SW
T
= +25°C
T
= +25°C
A
A
100
90
80
70
60
50
40
100
90
80
70
60
50
40
2.5V
OUT
2.5V
OUT
3.3V
1.5V
OUT
1.5V
OUT
OUT
1.8V
3.3V
1.8V
OUT
OUT
OUT
0.0 0.2 0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0 0.2
0.4
0.6
0.8
1.0
1.2
1.4 1.6
1.8
2.0
OUTPUT LOAD (A)
OUTPUT LOAD (A)
FIGURE 7. EFFICIENCY vs LOAD, f
= 2MHz, V = 5V, T = +25°C
FIGURE 6. EFFICIENCY vs LOAD, f
= 1MHz, V = 5V, T = +25°C
SW
IN
A
SW
IN
A
1.520
1.515
1.510
1.505
1.500
1.495
1.490
1.810
1.805
3.3V
IN
1.800
1.795
1.790
3.3V
IN
5V
IN
5V
1.785
IN
1.780
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8 2.0
OUTPUT LOAD (A)
OUTPUT LOAD (A)
FIGURE 8. V
OUT
REGULATION vs LOAD, f
= 2MHz, V
= 1.5V, T
FIGURE 9. V
OUT
REGULATION vs LOAD, f
= 2MHz, V
= 1.8V,
SW
OUT
A
SW
OUT
= +25°C
T = +25°C
A
FN6692.3
June 5, 2015
Submit Document Feedback
8
ISL80020, ISL80020A, ISL80015, ISL80015A
Typical Performance Curves(Continued)
2.505
2.500
2.495
2.490
2.485
2.480
2.475
3.335
3.330
3.325
3.320
3.315
3.310
3.305
3.3V PWM
IN
5V
IN
5V PWM
IN
0.0 0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0 0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
OUTPUT LOAD (A)
OUTPUT LOAD (A)
FIGURE 10. V
T
REGULATION vs LOAD, f
= +25°C
= 2MHz, V = 2.5V,
OUT
FIGURE 11. V
T
REGULATION vs LOAD, f
= +25°C
= 2MHz, V = 3.3V,
OUT
OUT
SW
OUT
SW
A
A
PHASE 5V/DIV
PHASE 5V/DIV
V
1V/DIV
OUT
V
1V/DIV
OUT
VEN 2V/DIV
PG 5V/DIV
VEN 2V/DIV
PG 5V/DIV
1ms/DIV
1ms/DIV
FIGURE 12. START-UP AT NO LOAD, f
= 2MHz, V = 5V,
IN
FIGURE 13. SHUTDOWN AT NO LOAD, f
= 2MHz, V = 5V,
SW IN
SW
T
= +25°C
T = +25°C
A
A
PHASE 5V/DIV
PHASE 5V/DIV
V
1V/DIV
OUT
V
1V/DIV
OUT
VEN 2V/DIV
PG 5V/DIV
VEN 2V/DIV
PG 5V/DIV
1ms/DIV
1ms/DIV
FIGURE 15. SHUTDOWN AT 2A LOAD, f
= 2MHz, V = 5V,
IN
FIGURE 14. START-UP AT 2A LOAD, f
= 2MHz, V = 5V,
IN
SW
SW
T
= +25°C
T
= +25°C
A
A
FN6692.3
June 5, 2015
Submit Document Feedback
9
ISL80020, ISL80020A, ISL80015, ISL80015A
Typical Performance Curves(Continued)
VEN 5V/DIV
VEN 5V/DIV
V
1V/DIV
OUT
V
1V/DIV
OUT
I
1A/DIV
L
PG 5V/DIV
I
1A/DIV
L
PG 5V/DIV
1ms/DIV
1ms/DIV
FIGURE 16. START-UP AT 1.5A LOAD, f
= 2MHz, V = 5V,
IN
FIGURE 17. SHUTDOWN AT 1.5A LOAD, f
= 2MHz, V = 5V,
SW IN
SW
T
= +25°C
T = +25°C
A
A
V
5V/DIV
1V/DIV
IN
V
5V/DIV
IN
V
OUT
I
1A/DIV
L
I
1A/DIV
L
PG 5V/DIV
V
1V/DIV
OUT
PG 5V/DIV
500µs/DIV
1ms/DIV
FIGURE 18. START-UP V AT 2A LOAD, f
IN
= 2MHz, V = 5V,
IN
FIGURE 19. SHUTDOWN V AT 2A LOAD, f
IN
= 2MHz, V = 5V,
SW IN
SW
T
= +25°C
T = +25°C
A
A
PHASE 1V/DIV
PHASE 1V/DIV
10ns/DIV
10ns/DIV
FIGURE 20. JITTER AT NO LOAD, f
= 2MHz, V = 5V, T = +25°C
IN
FIGURE 21. JITTER AT FULL LOAD, f
= 2MHz, V = 5V, T = +25°C
IN
SW
A
SW
A
FN6692.3
June 5, 2015
Submit Document Feedback
10
ISL80020, ISL80020A, ISL80015, ISL80015A
Typical Performance Curves(Continued)
PHASE 5V/DIV
V
RIPPLE 50mV/DIV
OUT
V
10mV/DIV
0.5A/DIV
OUT
I
L
I
1A/DIV
L
500ns/DIV
200µs/DIV
FIGURE 23. LOAD TRANSIENT, f
= 2MHz, V = 5V, T = +25°C
FIGURE 22. STEADY STATE AT NO LOAD, f
= 2MHz, V = 5V,
IN
SW
IN
A
SW
T
= +25°C
A
V
0.5V/DIV
OUT
I
1A/DIV
L
V
0.5V/DIV
OUT
PG 2V/DIV
PG 5V/DIV
1ms/DIV
500µs/DIV
FIGURE 24. OVERCURRENT PROTECTION, f
= 2MHz, V = 5V,
IN
FIGURE 25. OVER-TEMPERATURE PROTECTION, f
= 2MHz,
SW
SW
T
= +25°C
V
= 5V, T = +163°C
A
IN A
FN6692.3
June 5, 2015
Submit Document Feedback
11
ISL80020, ISL80020A, ISL80015, ISL80015A
turn off the P-FET immediately. The overcurrent function protects
the switching converter from a shorted output by monitoring the
current flowing through the upper MOSFET.
Theory of Operation
The device is a step-down switching regulator optimized for battery
powered applications. It operates at a high switching frequency
(1MHz or 2MHz), which enables the use of smaller inductors
resulting in small form factor, while also providing excellent
efficiency. The quiescent current is typically only 1.2µA when the
regulator is shut down.
Upon detection of overcurrent condition, the upper MOSFET will
be immediately turned off and will not be turned on again until
the next switching cycle. If the overcurrent condition goes away,
the output will resume back into regulation point.
Short-Circuit Protection
PWM Control Scheme
The short-circuit protection (SCP) comparator monitors the VFB
pin voltage for output short-circuit protection. When the VFB is
lower than 0.3V, the SCP comparator forces the PWM oscillator
frequency to drop to 1/3 of the normal operation value. This
comparator is effective during start-up or an output short-circuit
event.
The device employs the current-mode pulse-width modulation
(PWM) control scheme for fast transient response and
pulse-by-pulse current limiting. See “Functional Block Diagram” on
page 4. The current loop consists of the oscillator, the PWM
comparator, current sensing circuit and the slope compensation for
the current loop stability. The slope compensation is 900mV/Ts,
which changes with frequency. The gain for the current sensing
circuit is typically 300mV/A. The control reference for the current
loops comes from the error amplifier's (EAMP) output.
Negative Current Protection
Similar to the overcurrent, the negative current protection is
realized by monitoring the current across the low-side N-FET, as
shown in the “Functional Block Diagram” on page 4. When the
valley point of the inductor current reaches -1.5A for 2 consecutive
cycles, both P-FET and N-FET shut off. The 100Ω in parallel to the
N-FET will activate discharging the output into regulation. The
control will begin to switch when output is within regulation.
The PWM operation is initialized by the clock from the oscillator.
The P-channel MOSFET is turned on at the beginning of a PWM
cycle and the current in the MOSFET starts to ramp-up. When the
sum of the current amplifier CSA and the slope compensation
reaches the control reference of the current loop, the PWM
comparator COMP sends a signal to the PWM logic to turn off the
P-FET and turn on the N-Channel MOSFET. The N-FET stays on until
the end of the PWM cycle. Figure 26 shows the typical operating
waveforms during the PWM operation. The dotted lines illustrate
the sum of the slope compensation ramp and the current-sense
amplifier’s CSA output.
PG
PG is an output of a window comparator that continuously monitors
the buck regulator output voltage. PG is actively held low when EN is
low and during the buck regulator soft-start period. After 1ms delay
of the soft-start period, PG becomes high impedance as-long-as the
output voltage is within nominal regulation voltage set by VFB.
When VFB drops 15% below or raises 15% above the nominal
regulation voltage, the device pulls PG low. Any fault condition forces
PG low until the fault condition is cleared by attempts to soft-start.
There is an internal 5MΩ pull-up resistor to fit most applications. An
external resistor can be added from PG to VIN for more pull-up
strength.
V
EAMP
V
CSA
DUTY
CYCLE
UVLO
I
L
When the input voltage is below the undervoltage lock-out (UVLO)
threshold, the regulator is disabled.
V
OUT
Enable, Disable and Soft Start-up
After the VIN pin exceeds its rising POR trip point (nominal 2.5V),
the device begins operation. If the EN pin is held low externally,
nothing happens until this pin is released. Once the EN is
released and above the logic threshold, the internal default
soft-start time is 1ms.
FIGURE 26. PWM OPERATION WAVEFORMS
The reference voltage is 0.6V, which is used by Feedback to
adjust the output of the error amplifier, VEAMP. The error
amplifier is a trans conductance amplifier that converts the
voltage error signal to a current output. The voltage loop is
internally compensated with the 27pF and 200kΩ RC network.
The maximum EAMP voltage output is precisely clamped to 1.6V.
Discharge Mode (Soft-stop)
When a transition to shutdown mode occurs or the VIN UVLO is set,
the outputs discharge to GND through an internal 100Ω switch.
Overcurrent Protection
Thermal Shutdown
The overcurrent protection is realized by monitoring the CSA
output with the OCP comparator, as shown in the “Functional
Block Diagram” on page 4. The current sensing circuit has a gain
of 300mV/A, from the P-FET current to the CSA output. When the
CSA output reaches a threshold, the OCP comparator is tripped to
The device has built-in thermal protection. When the internal
temperature reaches +150°C, the regulator is completely
shutdown. As the temperature drops to +125°C, the device resume
operation by stepping through the soft-start.
FN6692.3
June 5, 2015
Submit Document Feedback
12
ISL80020, ISL80020A, ISL80015, ISL80015A
for optimized performance. The inductor ripple current can be
expressed as shown in Equation 4:
Power Derating Characteristics
To prevent the device from exceeding the maximum junction
temperature, some thermal analysis is required. The
temperature rise is given by Equation 2:
V
O
---------
V
1 –
O
(EQ. 4)
V
IN
--------------------------------------
I =
(EQ. 2)
L f
T
= PD
JA
SW
RISE
The inductor’s saturation current rating needs to be at least
larger than the peak current.
Where PD is the power dissipated by the regulator and θ is the
thermal resistance from the junction of the die to the ambient
JA
temperature. The junction temperature, T , is given by
Equation 3:
The device uses an internal compensation network and the
output capacitor value is dependent on the output voltage. The
ceramic capacitor is recommended to be X5R or X7R.
J
(EQ. 3)
T
= T + T
RISE
J
A
Output Voltage Selection
Where T is the ambient temperature. For the DFN package, the
A
The output voltage of the regulator can be programmed via an
external resistor divider that is used to scale the output voltage
relative to the internal reference voltage and feed it back to the
inverting input of the error amplifier.
θ
is +71°C/W.
JA
The actual junction temperature should not exceed the absolute
maximum junction temperature of +125°C when considering
the thermal design.
The output voltage programming resistor, R , will depend on the
1
value chosen for the feedback resistor and the desired output
voltage of the regulator. The value for the feedback resistor is
typically between 10kΩ and 100kΩas shown in Equation 5.
V
The device delivers full current at ambient temperatures up to
+85°C if the thermal impedance from the thermal pad
maintains the junction temperature below the thermal shutdown
level, depending on the input voltage/output voltage
combination and the switching frequency. The device power
dissipation must be reduced to maintain the junction
temperature at or below the thermal shutdown level. Figure 27
illustrates the approximate output current derating curve versus
ambient temperature for the ISL80020EVAL1Z kit.
O
(EQ. 5)
-----------
R
= R
– 1
1
2
VFB
If the output voltage desired is 0.6V, then R is left unpopulated
2
and R is shorted. There is a leakage current from VIN to PHASE.
1
It is recommended to preload the output with 10µA minimum.
For better performance, add 22pF in parallel with R
1
2.5
Input Capacitor Selection
2.0
The main functions for the input capacitor are to provide
decoupling of the parasitic inductance and to provide filtering
function to prevent the switching current flowing back to the
battery rail. At least two 22µF X5R or X7R ceramic capacitors are
a good starting point for the input capacitor selection.
1V
1.5
1.5V
1.0
2.5V
3.3V
Output Capacitor Selection
0.5
An output capacitor is required to filter the inductor current.
Output ripple voltage and transient response are two critical
factors when considering output capacitance choice. The current
mode control loop allows for the usage of low ESR ceramic
capacitors and thus smaller board layout. Electrolytic and
polymer capacitors may also be used.
V
= 5V, OLFM
IN
0
50
60
70
80
90
100
110
120
130
TEMPERATURE (°C)
FIGURE 27. DERATING CURVE vs TEMPERATURE
Applications Information
Output Inductor and Capacitor Selection
Additional consideration applies to ceramic capacitors. While
they offer excellent overall performance and reliability, the actual
in-circuit capacitance must be considered. Ceramic capacitors
are rated using large peak-to-peak voltage swings and with no DC
bias. In the DC/DC converter application, these conditions do not
reflect reality. As a result, the actual capacitance may be
considerably lower than the advertised value. Consult the
manufacturers datasheet to determine the actual in-application
capacitance. Most manufacturers publish capacitance vs DC bias
so this effect can be easily accommodated. The effects of AC
voltage are not frequently published, but an assumption of ~20%
further reduction will generally suffice. The result of these
considerations can easily result in an effective capacitance 50%
lower than the rated value. Nonetheless, they are a very good
To consider steady state and transient operations, the
ISL80020A and ISL80015A typically requires a 1.2µH, while the
ISL80020 and ISL80015 typically requires a 2.2µH output
inductor. Higher or lower inductor values can be used to optimize
the total converter system performance. For example, for higher
output voltage 3.3V application, in order to decrease the inductor
ripple current and output voltage ripple, the output inductor value
can be increased. It is recommended to set the inductor ripple
current to be approximately 30% of the maximum output current
FN6692.3
June 5, 2015
Submit Document Feedback
13
ISL80020, ISL80020A, ISL80015, ISL80015A
choice in many applications due to their reliability and extremely
low ESR.
Where V is the relative maximum overshoot
allowed during the removal of the load. For an overshoot of 5%,
the equation becomes Equation 9:
/V
OUTMAX OUT
Equations 6 and 7 allow calculation of the required capacitance
to meet a desired ripple voltage level. Additional capacitance
may be used.
2
I
L
*
OUT
-----------------------------------------------------
=
C
(EQ. 9)
OUT
2
2
V
1.05 – 1
*
OUT
For the ceramic capacitors (low ESR) =
I
Layout Considerations
The PCB layout is a very important converter design step to make
sure the designed converter works well. The power loop is
------------------------------------
V
=
(EQ. 6)
is the
OUTripple
8 f
C
OUT
SW
Where I is the inductor’s peak-to-peak ripple current, f
SW
switching frequency and C
composed of the output inductor L’s, the output capacitor C
,
OUT
is the output capacitor.
OUT
the PHASE’s pins and the PGND pin. It is necessary to make the
power loop as small as possible and the connecting traces
among them should be direct, short and wide. The switching
node of the converter, the PHASE pins and the traces connected
to the node are very noisy, so keep the voltage feedback trace
away from these noisy traces. The input capacitor should be
placed as closely as possible to the VIN pin and the ground of the
input and output capacitors should be connected as closely as
possible. The heat of the IC is mainly dissipated through the
thermal pad. Maximizing the copper area connected to the
thermal pad is preferable. In addition, a solid ground plane is
helpful for better EMI performance. It is recommended to add at
least 4 vias ground connection within the pad for the best
thermal relief.
If using electrolytic capacitors then:
V
= I*ESR
(EQ. 7)
OUTripple
Regarding transient response needs, a good starting point is to
determine the allowable overshoot in V if the load is suddenly
OUT
removed. In this case, energy stored in the inductor will be
transferred to C causing its voltage to rise. After calculating
OUT
capacitance required for both ripple and transient needs, choose
the larger of the calculated values. Equation 8 determines the
required output capacitor value in order to achieve a desired
overshoot relative to the regulated voltage.
2
I
L
*
OUT
--------------------------------------------------------------------------------------------
=
C
(EQ. 8)
OUT
2
2
V
V
V
– 1
*
OUT
OUTMAX
OUT
FN6692.3
June 5, 2015
Submit Document Feedback
14
ISL80020, ISL80020A, ISL80015, ISL80015A
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
CHANGE
June 5, 2015
FN6692.3 Added Related Literature on page 1.
-Thermal information table on page 6:
Updated:
-Junction Temperature Range: -55°C to +125°C to Maximum Junction Temperature (Plastic Package): +150°C
Added:
-Ambient Temperature Range: -40°C to +125°C
-Operating Junction Temperature Range: -40°C to +125°C
-Recommended Operating Conditions on page 6
Updated from “Junction Temperature Range: -40°C to +125°C” to “Temperature: -40°C to +125°C
-Electrical Specifications on page 6:
In heading:
-Changed temperature range, from -40°C to +85°C to: -40°C to +125°C.
-Changed from: “TJ = -40°C to +125°C to: “TA = -40°C to +125°C.
Under Output Regulation section for test condition updated:
-Feedback Voltage from: “TJ = -40°C to +125°C” to “TA = -40°C to +125°C”.
-VFB Bias Current from “VFB = 2.7V, TJ = -40°C to +125°C” to “VFB = 2.7V, TA = -40°C to +125°C”.
-Line Regulation from “TJ = -40°C to +125°C” to “TA = -40°C to +125°C”.
- POD L8.2x2C updated from rev 0 to rev 1. Changes since rev 0:
Tiebar Note updated
From: Tiebar shown (if present) is a non-functional feature.
To: Tiebar shown (if present) is a non-functional feature and may be located on any of the 4 sides (or ends).
April 1, 2015
FN6692.2 Under “Theory of Operation” on page 12, changed typical value from “5µA” to “1.2µA”.
Under “Enable, Disable and Soft Start-up” on page 12, changed typical value from “2.7V” to “2.5V”.
February 17, 2015
February 5, 2015
FN6692.1 Changed MIN value of VFB Bias Current in Electrical Spec Table from -120 to -350.
FN6692.0 Initial release
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6692.3
June 5, 2015
Submit Document Feedback
15
ISL80020, ISL80020A, ISL80015, ISL80015A
Package Outline Drawing
L8.2x2C
8 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE (TDFN) WITH E-PAD
Rev 1, 5/15
2.00
6
A
PIN #1 INDEX AREA
6
B
PIN 1
INDEX AREA
8
1
0.50
1.45±0.050
Exp.DAP
(4X)
0.15
0.25
( 8x0.30 )
0.10
C A B
M
TOP VIEW
0.80±0.050
Exp.DAP
BOTTOM VIEW
( 8x0.20 )
( 8x0.30 )
Package Outline
SEE DETAIL "X"
( 6x0.50 )
C
0.10
C
0 . 75 ( 0 . 80 max)
1.45
2.00
BASE PLANE
SEATING PLANE
0.08
C
SIDE VIEW
( 8x0.25 )
0.80
2.00
TYPICAL RECOMMENDED LAND PATTERN
0 . 2 REF
C
0 . 00 MIN.
0 . 05 MAX.
DETAIL "X"
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
Tiebar shown (if present) is a non-functional feature and may
be located on any of the 4 sides (or ends).
5.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
6.
FN6692.3
June 5, 2015
Submit Document Feedback
16
相关型号：
©2020 ICPDF网 联系我们和版权申明