IS25LP080D-JVLE [ISSI]
SERIAL FLASH MEMORY WITH 133MHZ MULTI I/O SPI & QUAD I/O QPI DTR INTERFACE;型号: | IS25LP080D-JVLE |
厂家: | INTEGRATED SILICON SOLUTION, INC |
描述: | SERIAL FLASH MEMORY WITH 133MHZ MULTI I/O SPI & QUAD I/O QPI DTR INTERFACE |
文件: | 总108页 (文件大小:1652K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IS25LP080D IS25WP080D
IS25WP040D
IS25WP020D
8/4/2Mb
SERIAL FLASH MEMORY WITH 133MHZ MULTI I/O SPI &
QUAD I/O QPI DTR INTERFACE
DATA SHEET
IS25LP080D
IS25WP080D/040D/020D
8/4/2Mb
SERIAL FLASH MEMORY WITH 133MHZ MULTI I/O SPI &
QUAD I/O QPI DTR INTERFACE
FEATURES
Industry Standard Serial Interface
Low Power with Wide Temp. Ranges
- IS25LP080D: 8Mbit/1Mbyte
- IS25WP080D: 8Mbit/1Mbyte
- IS25WP040D: 4Mbit/512Kbyte(Call
Factory)
- IS25WP020D: 2Mbit/256Kbyte(Call
Factory)
- 256 bytes per Programmable Page
- Supports standard SPI, Fast, Dual, Dual
I/O, Quad, Quad I/O, SPI DTR, Dual I/O
DTR, Quad I/O DTR, and QPI
- Supports Serial Flash Discoverable
Parameters (SFDP)
- Single Voltage Supply
IS25LP: 2.30V to 3.60V
IS25WP: 1.65V to 1.95V
- 10 mA Active Read Current
- 8 µA Standby Current
- 1 µA Deep Power Down
- Temp Grades:
Extended: -40°C to +105°C
Extended+: -40°C to +125°C(Call Factory)
Auto Grade: up to +125°C
Note: Extended+ should not be used for Automotive.
Advanced Security Protection
- Software and Hardware Write Protection
- Power Supply Lock Protect
- 4x256-Byte Dedicated Security Area
with OTP User-lockable Bits
High Performance Serial Flash (SPI)
- 50MHz Normal and 133Mhz Fast Read
- 532 MHz equivalent QPI
- DTR (Dual Transfer Rate) up to 66MHz
- Selectable Dummy Cycles
- Configurable Drive Strength
- Supports SPI Modes 0 and 3
- More than 100,000 Erase/Program Cycles
- More than 20-year Data Retention
- 128 bit Unique ID for Each Device
(Call Factory)
Industry Standard Pin-out & Packages(1)
- B = 8-pin SOIC 208mil
- N = 8-pin SOIC 150mil
- V = 8-pin VVSOP 150mil
- K = 8-contact WSON 6x5mm
- T = 8-contact USON 4x3mm
- U = 8-contact USON 2x3mm
- KGD (Call Factory)
Flexible & Efficient Memory Architecture
- Chip Erase with Uniform: Sector/Block
Erase (4/32/64 Kbyte)
- Program 1 to 256 Bytes per Page
- Program/Erase Suspend & Resume
Notes:
1. Call Factory for other package options available
Efficient Read and Program modes
- Low Instruction Overhead Operations
- Continuous Read 8/16/32/64-Byte
Burst Wrap
- Selectable Burst Length
- QPI for Reduced Instruction Overhead
- AutoBoot Operation
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
2
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
GENERAL DESCRIPTION
The IS25LP080D and IS25WP080D/040D/020D Serial Flash memory offers a versatile storage solution with high
flexibility and performance in a simplified pin count package. ISSI’s “Industry Standard Serial Interface” Flash is for
systems that require limited space, a low pin count, and low power consumption. The device is accessed through
a 4-wire SPI Interface consisting of a Serial Data Input (SI), Serial Data Output (SO), Serial Clock (SCK), and Chip
Enable (CE#) pins, which can also be configured to serve as multi-I/O (see pin descriptions).
The device supports Dual and Quad I/O as well as standard, Dual Output, and Quad Output SPI. Clock frequencies
of up to 133MHz allow for equivalent clock rates of up to 532MHz (133MHz x 4) which equates to 66Mbytes/s of
data throughput. The IS25xP series of Flash adds support for DTR (Double Transfer Rate) commands that transfer
addresses and read data on both edges of the clock. These transfer rates can outperform 16-bit Parallel Flash
memories allowing for efficient memory access to support XIP (execute in place) operation.
The memory array is organized into programmable pages of 256-bytes. This family supports page program mode
where 1 to 256 bytes of data are programmed in a single command. QPI (Quad Peripheral Interface) supports 2-
cycle instruction further reducing instruction times. Pages can be erased in groups of 4Kbyte sectors, 32Kbyte
blocks, 64Kbyte blocks, and/or the entire chip. The uniform sector and block architecture allows for a high degree
of flexibility so that the device can be utilized for a broad variety of applications requiring solid data retention.
GLOSSARY
Standard SPI
In this operation, a 4-wire SPI Interface is utilized, consisting of Serial Data Input (SI), Serial Data Output (SO),
Serial Clock (SCK), and Chip Enable (CE#) pins. Instructions are sent via the SI pin to encode instructions,
addresses, or input data to the device on the rising edge of SCK. The SO pin is used to read data or to check the
status of the device. This device supports SPI bus operation modes (0, 0) and (1, 1).
Multi I/O SPI
Multi-I/O operation utilizes an enhanced SPI protocol to allow the device to function with Dual Output, Dual Input
and Output, Quad Output, and Quad Input and Output capability. Executing these instructions through SPI mode
will achieve double or quadruple the transfer bandwidth for READ and PROGRAM operations.
QPI
The device supports Quad Peripheral Interface (QPI) operations only when the device is switched from
Standard/Dual/Quad SPI mode to QPI mode using the enter QPI (35h) instruction. The typical SPI protocol requires
that the byte-long instruction code being shifted into the device only via SI pin in eight serial clocks. The QPI mode
utilizes all four I/O pins to input the instruction code thus requiring only two serial clocks. This can significantly
reduce the SPI instruction overhead and improve system performance. Only QPI mode or SPI/Dual/Quad mode
can be active at any given time. Enter QPI (35h) and Exit QPI (F5h) instructions are used to switch between these
two modes, regardless of the non-volatile Quad Enable (QE) bit status in the Status Register. Power Reset or
Software Reset will return the device into the standard SPI mode. SI and SO pins become bidirectional I/O0 and
I/O1, and WP# and HOLD# pins become I/O2 and I/O3 respectively during QPI mode.
DTR
In addition to SPI and QPI features, the device also supports SPI DTR READ. SPI DTR allows high data throughput
while running at lower clock frequencies. SPI DTR READ mode uses both rising and falling edges of the clock to
drive output, resulting in reducing input and output cycles by half.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
3
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
TABLE OF CONTENTS
FEATURES............................................................................................................................................................2
GENERAL DESCRIPTION ....................................................................................................................................3
TABLE OF CONTENTS.........................................................................................................................................4
1. PIN CONFIGURATION...................................................................................................................................7
2. PIN DESCRIPTIONS......................................................................................................................................8
3. BLOCK DIAGRAM..........................................................................................................................................9
4. SPI MODES DESCRIPTION ........................................................................................................................10
5. SYSTEM CONFIGURATION........................................................................................................................12
5.1 BLOCK/SECTOR ADDRESSES ............................................................................................................12
6. REGISTERS .................................................................................................................................................13
6.1 STATUS REGISTER ..............................................................................................................................13
6.2 FUNCTION REGISTER..........................................................................................................................16
6.3 READ REGISTER AND EXTENDED REGISTER..................................................................................17
6.4 AUTOBOOT REGISTER ........................................................................................................................21
7. PROTECTION MODE...................................................................................................................................22
7.1 HARDWARE WRITE PROTECTION......................................................................................................22
7.2 SOFTWARE WRITE PROTECTION ......................................................................................................22
8. DEVICE OPERATION ..................................................................................................................................23
8.1 NORMAL READ OPERATION (NORD, 03h).........................................................................................26
8.2 FAST READ OPERATION (FRD, 0Bh) ..................................................................................................28
8.3 HOLD OPERATION................................................................................................................................30
8.4 FAST READ DUAL I/O OPERATION (FRDIO, BBh) .............................................................................30
8.5 FAST READ DUAL OUTPUT OPERATION (FRDO, 3Bh).....................................................................33
8.6 FAST READ QUAD OUTPUT OPERATION (FRQO, 6Bh)....................................................................34
8.7 FAST READ QUAD I/O OPERATION (FRQIO, EBh) ............................................................................36
8.8 PAGE PROGRAM OPERATION (PP, 02h)............................................................................................40
8.9 QUAD INPUT PAGE PROGRAM OPERATION (PPQ, 32h/38h) ..........................................................42
8.10 ERASE OPERATION ...........................................................................................................................43
8.11 SECTOR ERASE OPERATION (SER, D7h/20h).................................................................................44
8.12 BLOCK ERASE OPERATION (BER32K:52h, BER64K:D8h) ..............................................................45
8.13 CHIP ERASE OPERATION (CER, C7h/60h).......................................................................................47
8.14 WRITE ENABLE OPERATION (WREN, 06h) ......................................................................................48
8.15 WRITE DISABLE OPERATION (WRDI, 04h).......................................................................................49
8.16 READ STATUS REGISTER OPERATION (RDSR, 05h) .....................................................................50
8.17 WRITE STATUS REGISTER OPERATION (WRSR, 01h)...................................................................51
8.18 READ FUNCTION REGISTER OPERATION (RDFR, 48h).................................................................52
8.19 WRITE FUNCTION REGISTER OPERATION (WRFR, 42h)...............................................................53
8.20 ENTER QUAD PERIPHERAL INTERFACE (QPI) MODE OPERATION (QPIEN, 35h; QPIDI, F5h)..54
8.21 PROGRAM/ERASE SUSPEND & RESUME........................................................................................55
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
4
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.22 ENTER DEEP POWER DOWN (DP, B9h)...........................................................................................57
8.23 RELEASE DEEP POWER DOWN (RDPD, ABh).................................................................................58
8.24 SET READ PARAMETERS OPERATION (SRPNV: 65h, SRPV: C0h/63h) ........................................59
8.25 SET EXTENDED READ PARAMETERS OPERATION (SERPNV: 85h, SERPV: 83h) ......................61
8.26 READ READ PARAMETERS OPERATION (RDRP, 61h)...................................................................62
8.27 READ EXTENDED READ PARAMETERS OPERATION (RDERP, 81h)............................................63
8.28 CLEAR EXTENDED READ PARAMETERS OPERATION (CLERP, 82h) ..........................................64
8.29 READ PRODUCT IDENTIFICATION (RDID, ABh) ..............................................................................65
8.30 READ PRODUCT IDENTIFICATION BY JEDEC ID OPERATION (RDJDID, 9Fh; RDJDIDQ, AFh)..67
8.31 READ DEVICE MANUFACTURER AND DEVICE ID OPERATION (RDMDID, 90h)..........................68
8.31 READ UNIQUE ID NUMBER (RDUID, 4Bh) ........................................................................................69
8.32 READ SFDP OPERATION (RDSFDP, 5Ah) ........................................................................................70
8.33 NO OPERATION (NOP, 00h)...............................................................................................................70
8.34 SOFTWARE RESET (RESET-ENABLE (RSTEN, 66h) AND RESET (RST, 99h)) AND HARDWARE
RESET ..........................................................................................................................................................71
8.35 SECURITY INFORMATION ROW........................................................................................................72
8.36 INFORMATION ROW ERASE OPERATION (IRER, 64h) ...................................................................73
8.37 INFORMATION ROW PROGRAM OPERATION (IRP, 62h) ...............................................................74
8.38 INFORMATION ROW READ OPERATION (IRRD, 68h) .....................................................................75
8.39 FAST READ DTR MODE OPERATION In SPI MODE (FRDTR, 0Dh)................................................76
8.40 FAST READ DUAL IO DTR MODE OPERATION (FRDDTR, BDh) ....................................................78
8.41 FAST READ QUAD IO DTR MODE OPERATION IN SPI MODE (FRQDTR, EDh)............................81
8.42 SECTOR LOCK/UNLOCK FUNCTIONS..............................................................................................85
8.43 AUTOBOOT..........................................................................................................................................87
9. ELECTRICAL CHARACTERISTICS.............................................................................................................91
9.1 ABSOLUTE MAXIMUM RATINGS (1) .....................................................................................................91
9.2 OPERATING RANGE.............................................................................................................................91
9.3 DC CHARACTERISTICS........................................................................................................................92
9.4 AC MEASUREMENT CONDITIONS ......................................................................................................93
9.5 PIN CAPACITANCE ...............................................................................................................................93
9.6 AC CHARACTERISTICS........................................................................................................................94
9.7 SERIAL INPUT/OUTPUT TIMING..........................................................................................................96
9.8 POWER-UP AND POWER-DOWN ........................................................................................................98
9.9 PROGRAM/ERASE PERFORMANCE...................................................................................................99
9.10 RELIABILITY CHARACTERISTICS .....................................................................................................99
10.
PACKAGE TYPE INFORMATION.........................................................................................................100
10.1 8-Pin JEDEC 208mil Broad Small Outline Integrated Circuit (SOIC) Package (B) ............................100
10.2 8-Pin JEDEC 150mil Broad Small Outline Integrated Circuit (SOIC) Package (N)............................101
10.3 8-Pin 150mil VVSOP Package (V)......................................................................................................102
10.4 8-Contact Ultra-Thin Small Outline No-Lead (USON) Package 2x3mm (U) ......................................103
10.5 8-Contact Ultra-Thin Small Outline No-Lead (USON) Package 4x3mm (T).......................................104
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
5
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.6 8-Contact Ultra-Thin Small Outline No-Lead (WSON) Package 6x5mm (K)......................................105
11.
ORDERING INFORMATION - Valid Part Numbers...............................................................................106
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
6
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
1. PIN CONFIGURATION
CE#
Vcc
1
2
8
7
Vcc
8
7
6
5
CE#
1
HOLD# or
RESET# (IO3)(1)
SO (IO1)
HOLD# or
RESET# (IO3)
(1)
SO (IO1)
2
SCK
WP# (IO2)
GND
3
SCK
WP# (IO2)
GND
3
4
6
5
4
SI (IO0)
SI (IO0)
8-pin USON 2x3mm (Package: U)
8-pin USON 4x3mm (Package: T)
8-pin WSON 6x5mm (Package: K)
8-pin SOIC 208mil (Package: B)
8-pin SOIC 150mil (Package: N)
8-pin VVSOP 150mil (Package: V)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
7
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
2. PIN DESCRIPTIONS
SYMBOL
TYPE
DESCRIPTION
Chip Enable: The Chip Enable (CE#) pin enables and disables the devices
operation. When CE# is high the device is deselected and output pins are in a high
impedance state. When deselected the devices non-critical internal circuitry power
down to allow minimal levels of power consumption while in a standby state.
When CE# is pulled low the device will be selected and brought out of standby mode.
The device is considered active and instructions can be written to, data read, and
written to the device. After power-up, CE# must transition from high to low before a
new instruction will be accepted.
CE#
INPUT
Keeping CE# in a high state deselects the device and switches it into its low power
state. Data will not be accepted when CE# is high.
Serial Data Input, Serial Output, and IOs (SI, SO, IO0, and IO1):
This device supports standard SPI, Dual SPI, and Quad SPI operation. Standard SPI
instructions use the unidirectional SI (Serial Input) pin to write instructions,
addresses, or data to the device on the rising edge of the Serial Clock (SCK).
Standard SPI also uses the unidirectional SO (Serial Output) to read data or status
from the device on the falling edge of the serial clock (SCK).
SI (IO0),
SO (IO1)
INPUT/OUTPUT
In Dual and Quad SPI mode, SI and SO become bidirectional IO pins to write
instructions, addresses or data to the device on the rising edge of the Serial Clock
(SCK) and read data or status from the device on the falling edge of SCK. Quad SPI
instructions use the WP# and HOLD# pins as IO2 and IO3 respectively.
Write Protect/Serial Data IO (IO2): The WP# pin protects the Status Register from
being written in conjunction with the SRWD bit. When the SRWD is set to “1” and the
WP# is pulled low, the Status Register bits (SRWD, QE, BP3, BP2, BP1, BP0) are
write-protected and vice-versa for WP# high. When the SRWD is set to “0”, the Status
Register is not write-protected regardless of WP# state.
WP# (IO2)
INPUT/OUTPUT
When the QE bit is set to “1”, the WP# pin (Write Protect) function is not available
since this pin is used for IO2.
HOLD# or RESET#/Serial Data IO (IO3): When the QE bit of Status Register is set
to “1”, HOLD# pin or RESET# is not available since it becomes IO3. When QE=0, the
pin acts as HOLD# or RESET# and either one can be selected by the P7 bit setting
in Read Register. HOLD# will be selected if P7=0 (Default) and RESET# will be
selected if P7=1.
The HOLD# pin allows the device to be paused while it is selected. It pauses serial
communication by the master device without resetting the serial sequence. The
HOLD# pin is active low. When HOLD# is in a low state and CE# is low, the SO pin
will be at high impedance. Device operation can resume when HOLD# pin is brought
to a high state.
HOLD# or
RESET# (IO3)
INPUT/OUTPUT
RESET# pin is a hardware RESET signal. When RESET# is driven HIGH, the
memory is in the normal operating mode. When RESET# is driven LOW, the memory
enters reset mode and output is High-Z. If RESET# is driven LOW while an internal
WRITE, PROGRAM, or ERASE operation is in progress, data may be lost.
Serial Data Clock: Synchronized Clock for input and output timing operations.
Power: Device Core Power Supply
SCK
Vcc
INPUT
POWER
GROUND
Unused
Ground: Connect to ground when referenced to Vcc
GND
NC
NC: Pins labeled “NC” stand for “No Connect” and should be left unconnected.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
8
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
3. BLOCK DIAGRAM
Control Logic
High Voltage Generator
Status
Register
I/O Buffers and
Data Latches
256 Bytes
Page Buffer
CE#
SCK
WP#
(IO2)
Y-Decoder
SI
(IO0)
SO
(IO1)
HOLD# or RESET#(1)
(IO3)
Memory Array
Address Latch &
Counter
Note1: According to the P7 bit setting in Read Register, either HOLD# (P7=0) or RESET# (P7=1) pin can be selected.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
9
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
4. SPI MODES DESCRIPTION
Multiple IS25LP080D device or multiple IS25WP080D/040D/020D devices can be connected on the SPI serial bus
and controlled by a SPI Master, i.e. microcontroller, as shown in Figure 4.1. The devices support either of two SPI
modes:
Mode 0 (0, 0)
Mode 3 (1, 1)
The difference between these two modes is the clock polarity. When the SPI master is in stand-by mode, the serial
clock remains at “0” (SCK = 0) for Mode 0 and the clock remains at “1” (SCK = 1) for Mode 3. Please refer to Figure
4.2 and Figure 4.3 for SPI and QPI mode. In both modes, the input data is latched on the rising edge of Serial Clock
(SCK), and the output data is available from the falling edge of SCK.
Figure 4.1 Connection Diagram among SPI Master and SPI Slaves (Memory Devices)
SDO
SDI
SPI interface with
(0,0) or (1,1)
SCK
SCK SO SI
SCK SO SI
SCK SO SI
SPI Master
(i.e. Microcontroller)
SPI
SPI
SPI
Memory
Device
Memory
Device
Memory
Device
CS3
CS2
CS1
CE#
CE#
CE#
HOLD# or(1)
HOLD# or (1)
HOLD# or(1)
WP#
WP#
WP#
RESET
RESET#
RESET#
Notes:
1. According to the P7 bit setting in Read Register, either HOLD# (P7=0) or RESET# (P7=1) pin can be selected.
2. SI and SO pins become bidirectional IO0 and IO1 respectively during Dual I/O mode and SI, SO, WP#, and HOLD#
pins become bidirectional IO0, IO1, IO2, and IO3 respectively during Quad I/O or QPI mode.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
10
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 4.2 SPI Mode Support
SCK
Mode 0 (0,0)
SCK
Mode 3 (1,1)
MSB
SI
SO
MSB
Figure 4.3 QPI Mode Support
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
3-byte Address
Mode Bits
Data 1
Data 2
Data 3
...
...
...
...
IO0
IO1
4
5
6
7
4
C4
C5
C6
C0
C1
C2
0
1
2
3
4
0
1
2
3
0
1
2
3
4
0
1
2
3
4
0
1
2
3
20
21
16
17
18
19
12
13
14
15
8
9
5
5
5
5
IO2
IO3
6
6
6
6
22
10
11
71
71
231
71
C71 C3
71
Note1: MSB (Most Significant Bit)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
11
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
5. SYSTEM CONFIGURATION
The memory array is divided into uniform 4 Kbyte sectors or uniform 32/64 Kbyte blocks (a block consists of
eight/sixteen adjacent sectors respectively).
Table 5.1 illustrates the memory map of the device. The Status Register controls how the memory is protected.
5.1 BLOCK/SECTOR ADDRESSES
Table 5.1 Block/Sector Addresses
Block No.
(64Kbyte)
Block No.
(32Kbyte)
Sector Size
(Kbytes)
Memory Density
Sector No.
Address Range
Sector 0
4
:
000000h – 000FFFh
Block 0
Block 1
Block 2
:
:
Block 0
:
:
:
Sector 15
4
4
:
00F000h - 00FFFFh
Sector 16
010000h – 010FFFh
:
:
Block 1
2Mb(1)
:
:
:
Block 3
:
Sector 31
4
01F000h - 01FFFFh
:
Block 3
:
:
:
:
4Mb(1)
Sector 48
4
:
030000h – 030FFFh
Block 6
:
:
:
:
:
8Mb
Block 7
:
Sector 63
4
03F000h – 03FFFFh
:
:
:
Sector 112
4
:
070000h – 070FFFh
Block 14
:
:
Block 7
:
:
:
:
Block 15
:
Sector 127
4
07F000h – 07FFFFh
:
:
:
Sector 240
4
:
0F0000h – 0F0FFFh
Block 30
:
:
Block 15
:
:
:
Block 31
Sector 255
4
0FF000h – 0FFFFFh
Note:
1. 4Mb/2Mb will be available only for 1.8V device.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
12
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
6. REGISTERS
The device has four sets of Registers: Status, Function, Read, and Autoboot.
6.1 STATUS REGISTER
Status Register Format and Status Register Bit Definitions are described in Table 6.1 & Table 6.2.
Table 6.1 Status Register Format
Bit 7
SRWD
0
Bit 6
QE
0
Bit 5
BP3
0
Bit 4
BP2
0
Bit 3
BP1
0
Bit 2
BP0
0
Bit 1
WEL
0
Bit 0
WIP
0
Default
Table 6.2 Status Register Bit Definition
Read-
/Write
Bit
Name
Definition
Type
Write In Progress Bit:
"0" indicates the device is ready(default)
"1" indicates a write cycle is in progress and the device is busy
Write Enable Latch:
"0" indicates the device is not write enabled (default)
"1" indicates the device is write enabled
Bit 0
WIP
R
Volatile
Volatile
Bit 1
WEL
R/W1
Bit 2
Bit 3
Bit 4
Bit 5
BP0
BP1
BP2
BP3
Block Protection Bit: (See Table 6.4 for details)
"0" indicates the specific blocks are not write-protected (default)
"1" indicates the specific blocks are write-protected
R/W
Non-Volatile
Quad Enable bit:
Bit 6
Bit 7
QE
“0” indicates the Quad output function disable (default)
“1” indicates the Quad output function enable
Status Register Write Disable: (See Table 7.1 for details)
"0" indicates the Status Register is not write-protected (default)
"1" indicates the Status Register is write-protected
R/W
R/W
Non-Volatile
Non-Volatile
SRWD
Note1: WEL bit can be written by WREN and WRDI commands, but cannot by WRSR command.
The BP0, BP1, BP2, BP3, QE, and SRWD are non-volatile memory cells that can be written by a Write Status
Register (WRSR) instruction. The default value of the BP0, BP1, BP2, BP3, QE, and SRWD bits were set to “0” at
factory. The Status Register can be read by the Read Status Register (RDSR).
The function of Status Register bits are described as follows:
WIP bit: Write In Progress (WIP) is read-only, and can be used to detect the progress or completion of a Program,
Erase, or Write/Set Non-Volatile/OTP Register operation. WIP is set to “1” (busy state) when the device is executing
the operation. During this time the device will ignore further instructions except for Read Status/Function/Extended
Read Register and Software/Hardware Reset instructions. In addition to the instructions, an Erase/Program
Suspend instruction also can be executed during a Program or an Erase operation. When an operation has
completed, WIP is cleared to “0” (ready state) whether the operation is successful or not and the device is ready
for further instructions.
WEL bit: Write Enable Latch (WEL) indicates the status of the internal write enable latch. When WEL is “0”, the
internal write enable latch is disabled and the write operations described in Table 6.3 are inhibited. When WEL is
“1”, the Write operations are allowed. WEL bit is set by a Write Enable (WREN) instruction. Each Write Non-Volatile
Register, Program and Erase instruction must be preceded by a WREN instruction. The volatile register related
commands such as the Set Volatile Read Register and the Set Volatile Extended Read Register don’t require to
set WEL to “1". WEL can be reset by a Write Disable (WRDI) instruction. It will automatically reset after the
completion of any Write operation.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
13
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Table 6.3 Instructions requiring WREN instruction ahead
Instructions must be preceded by the WREN instruction
Operation
Name
Hex Code
02h
PP
Serial Input Page Program
Quad Input Page Program
Sector Erase 4KB
PPQ
32h/38h
D7h/20h
52h
SER
BER32 (32KB)
BER64 (64KB)
CER
Block Erase 32KB
D8h
Block Erase 64KB
C7h/60h
01h
Chip Erase
WRSR
WRFR
SRPNV
SERPNV
IRER
Write Status Register
Write Function Register
Set Read Parameters (Non-Volatile)
42h
65h
85h
Set Extended Read Parameters (Non-Volatile)
Erase Information Row
64h
IRP
62h
Program Information Row
WRABR
15h
Write AutoBoot Register
BP3, BP2, BP1, BP0 bits: The Block Protection (BP3, BP2, BP1 and BP0) bits are used to define the portion of
the memory area to be protected. Refer to Table 6.4 for the Block Write Protection (BP) bit settings. When a defined
combination of BP3, BP2, BP1 and BP0 bits are set, the corresponding memory area is protected. Any program or
erase operation to that area will be inhibited.
Note: A Chip Erase (CER) instruction will be ignored unless all the Block Protection Bits are “0”s.
SRWD bit: The Status Register Write Disable (SRWD) bit operates in conjunction with the Write Protection (WP#)
signal to provide a Hardware Protection Mode. When the SRWD is set to “0”, the Status Register is not write-
protected. When the SRWD is set to “1” and the WP# is pulled low (VIL), the bits of Status Register (SRWD, QE,
BP3, BP2, BP1, BP0) become read-only, and a WRSR instruction will be ignored. If the SRWD is set to “1” and
WP# is pulled high (VIH), the Status Register can be changed by a WRSR instruction.
QE bit: The Quad Enable (QE) is a non-volatile bit in the Status Register that allows quad operation. When the QE
bit is set to “0”, the pin WP# and HOLD#/RESET# are enabled. When the QE bit is set to “1”, the IO2 and IO3 pins
are enabled.
WARNING: The QE bit must be set to 0 if WP# or HOLD#/RESET# pin is tied directly to the power supply.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
14
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Table 6.4 Block (64Kbyte) assignment by Block Write Protect (BP) Bits
Status Register Bits
Protected Memory Area
4 Mbit(1)
BP3 BP2 BP1 BP0
8 Mbit
2 Mbit(1)
None
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
None
None
1 block : 15
1 block : 7
1 block : 3
2 blocks : 2 - 3
2 blocks : 14 - 15
4 blocks : 12 - 15
8 blocks : 8 - 15
2 blocks : 6 - 7
4 blocks : 4 - 7
All Blocks
All Blocks
All Blocks
8 blocks : 0 - 7
4 blocks : 0 - 3
2 blocks : 0 - 1
1 block : 0
4 blocks : 0 - 3
2 blocks : 0 - 1
1 block : 0
None
2 blocks : 0 - 1
1 block : 0
None
None
Note:
1. 4Mb/2Mb will be available only for 1.8V device.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
15
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
6.2 FUNCTION REGISTER
Function Register Format and Bit definition are described in Table 6.5 and Table 6.6.
Table 6.5 Function Register Format
Bit 7
IRL3
0
Bit 6
IRL2
0
Bit 5
IRL1
0
Bit 4
IRL0
0
Bit 3
ESUS
0
Bit 2
PSUS
0
Bit 1
Reserved
0
Bit 0
Reserved
0
Default
Table 6.6 Function Register Bit Definition
Read
/Write
Bit
Name
Definition
Type
Bit 0
Bit 1
Reserved
Reserved
Reserved
Reserved
R
R
Reserved
Reserved
Program suspend bit:
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
PSUS
“0” indicates program is not suspend
“1” indicates program is suspend
Erase suspend bit:
"0" indicates Erase is not suspend
"1" indicates Erase is suspend
Lock the Information Row 0:
“0” indicates the Information Row can be programmed
“1” indicates the Information Row cannot be programmed
Lock the Information Row 1:
“0” indicates the Information Row can be programmed
“1” indicates the Information Row cannot be programmed
Lock the Information Row 2:
“0” indicates the Information Row can be programmed
“1” indicates the Information Row cannot be programmed
Lock the Information Row 3:
“0” indicates the Information Row can be programmed
“1” indicates the Information Row cannot be programmed
R
Volatile
Volatile
OTP
ESUS
R
IR Lock 0
IR Lock 1
IR Lock 2
IR Lock 3
R/W
R/W
R/W
R/W
OTP
OTP
OTP
Note: Once OTP bits of Function Register are written to “1”, it cannot be modified to “0” any more.
PSUS bit: The Program Suspend Status bit indicates when a Program operation has been suspended. The PSUS
changes to “1” after a suspend command is issued during the program operation. Once the suspended Program
resumes, the PSUS bit is reset to “0”.
ESUS bit: The Erase Suspend Status bit indicates when an Erase operation has been suspended. The ESUS bit
is “1” after a suspend command is issued during an Erase operation. Once the suspended Erase resumes, the
ESUS bit is reset to “0”.
IR Lock bit 0 ~ 3: The default is “0” so that the Information Row can be programmed. If the bit set to “1”, the
Information Row can’t be programmed. Once it set to “1”, it cannot be changed back to “0” since IR Lock bits are
OTP.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
16
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
6.3 READ REGISTER AND EXTENDED REGISTER
Read Register format and Bit definitions are described below. Read Register and Extended Read Register consist
of a pair of rewritable non-volatile register and volatile register, respectively. During power up sequence, volatile
register will be loaded with the value of non-volatile value.
6.3.1 READ REGISTER
Table 6.7 and Table 6.8 define all bits that control features in SPI/QPI modes. HOLD#/RESET# pin selection (P7)
bit is used to select HOLD# pin or RESET# pin in SPI mode when QE=“0”.
When QE=1 or in QPI mode, P7 bit setting will be ignored since the pin becomes IO3..
The Dummy Cycle bits (P6, P5, P4, P3) define how many dummy cycles are used during various READ modes.
The wrap selection bits (P2, P1, P0) define burst length with an enable bit.
The SET READ PARAMETERS Operations (SRPNV: 65h, SRPV: C0h or 63h) are used to set all the Read Register
bits, and can thereby define HOLD#/RESET# pin selection, dummy cycles, and burst length with wrap around.
SRPNV is used to set the non-volatile register and SRPV is used to set the volatile register.
Table 6.7 Read Register Parameter Bit Table
P7
P6
P5
P4
P3
P2
P1
P0
HOLD#/
RESET#
Dummy
Cycles
Dummy
Cycles
Dummy
Cycles
Dummy
Cycles
Wrap
Enable
Burst
Length
Burst
Length
Default
0
0
0
0
0
0
0
0
Table 6.8 Read Register Bit Definition
Read-
/Write
Bit
P0
P1
Name
Definition
Type
Non-Volatile
and Volatile
Non-Volatile
and Volatile
Burst Length
Burst Length
Burst Length
Burst Length
R/W
R/W
R/W
Burst Length Set Enable Bit:
"0" indicates disable (default)
"1" indicates enable
Burst Length
Set Enable
Non-Volatile
and Volatile
P2
Non-Volatile
and Volatile
Non-Volatile
and Volatile
Non-Volatile
and Volatile
Non-Volatile
and Volatile
P3
P4
P5
P6
Dummy Cycles
Dummy Cycles
Dummy Cycles
Dummy Cycles
R/W
R/W
R/W
R/W
Number of Dummy Cycles:
Bits1 to Bit4 can be toggled to select the number of dummy cycles
(1 to 15 cycles)
HOLD#/RESET# pin selection Bit:
"0" indicates the HOLD# pin is selected (default)
"1" indicates the RESET# pin is selected
HOLD#/
RESET#
Non-Volatile
and Volatile
P7
R/W
Table 6.9 Burst Length Data
P1
0
P0
0
8 bytes
16 bytes
32 bytes
64 bytes
0
1
1
0
1
1
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
17
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Table 6.10 Wrap Function
Wrap around boundary
P2
0
Whole array regardless of P1 and P0 value
Burst Length set by P1 and P0
1
Table 6.11 Read Dummy Cycles vs Max Frequency
Fast Read
Fast Read
Quad
Output
6Bh
Fast Read
Dual IO
BBh
Fast Read
Quad IO
EBh
Fast Read5 Fast Read5
Dual
Output
3Bh
FRDTR
0Dh
FRDDTR
BDh
FRQDTR
EDh
Dummy
0Bh
0Bh
P[6:3]
Cycles2,3
SPI
QPI
SPI
SPI
SPI
SPI, QPI
104MHz
33MHz
SPI/QPI
SPI4
SPI, QPI
66MHz
20MHz
33MHz
46MHz
60MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
0
1
Default1
133MHz
84MHz
104MHz
33MHz
133MHz
84MHz
115MHz
60MHz
133MHz
66MHz
66/66MHz
50/20MHz
66/33MHz
66/46MHz
66/60MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66/66MHz
66MHz
33MHz
50MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
66MHz
1
2
2
104MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
50MHz
104MHz
115MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
84MHz
80MHz
50MHz
3
3
60MHz
104MHz
115MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
90MHz
60MHz
4
4
70MHz
104MHz
115MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
70MHz
5
5
84MHz
84MHz
6
6
104MHz
115MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
104MHz
115MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
133MHz
7
7
8
8
9
9
10
11
12
13
14
15
10
11
12
13
14
15
Notes:
1. Default dummy cycles are as follows.
Command
Normal mode DTR mode
Dummy Cycles
Operation
Comment
Normal mode
DTR mode
Fast Read (SPI mode)
0Bh
0Bh
3Bh
BBh
6Bh
EBh
EBh
0Dh
0Dh
-
8
6
8
4
8
6
6
8
6
-
RDUID, IRRD instructions are also
applied.
Fast Read (QPI mode)
Fast Read Dual Output
Fast Read Dual IO SPI
BDh
-
4
-
Fast Read Quad Output
Fast Read Quad IO (SPI mode)
Fast Read Quad IO (QPI mode)
EDh
EDh
6
6
2. Enough number of dummy cycles must be applied to execute properly the AX read operation.
3. Must satisfy bus I/O contention. For instance, if the number of dummy cycles and AX bit cycles are same, then X
must be Hi-Z.
4. QPI mode is not available for FRDDTR command.
5. RDUID, IRRD instructions are also applied.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
18
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
6.3.2 EXTENDED READ REGISTER
Table 6.12 and Table 6.13 define all bits that control features in SPI/QPI modes. The ODS2, ODS1, ODS0 (EB7,
EB6, EB5) bits provide a method to set and control driver strength. The four bits (EB3, EB2, EB1, EB0) are read-
only bits and may be checked to know what the WIP status is or whether there is an error during an Erase, Program,
or Write/Set Register operation. These bits are not affected by SERPNV or SERPV commands. EB4 bit remains
reserved for future use.
The SET EXTENDED READ PARAMETERS Operations (SERPNV: 85h, SERPV: 83h) are used to set all the
Extended Read Register bits, and can thereby define the output driver strength used during READ modes. SRPNV
is used to set the non-volatile register and SRPV is used to set the volatile register.
Table 6.12 Extended Read Register Bit Table
EB7
ODS2
1
EB6
ODS1
1
EB5
ODS0
1
EB4
Reserved
1
EB3
E_ERR
0
EB2
P_ERR
0
EB1
PROT_E
0
EB0
WIP
0
Default
Table 6.13 Extended Read Register Bit Definition
Read-
/Write
Bit
Name
Definition
Type
Write In Progress Bit:
EB0
WIP
Has exactly same function as the bit0 (WIP) of Status Register
“0”: Ready, “1”: Busy
Protection Error Bit:
"0" indicates no error
"1" indicates protection error in an Erase or a Program operation
Program Error Bit:
"0" indicates no error
"1" indicates an Program operation failure or protection error
Erase Error Bit:
R
R
R
R
Volatile
EB1
EB2
EB3
PROT_E
P_ERR
E_ERR
Volatile
Volatile
"0" indicates no error
Volatile
"1" indicates a Erase operation failure or protection error
EB4
EB5
Reserved
ODS0
Reserved
R
Reserved
Non-Volatile
and Volatile
Non-Volatile
and Volatile
Non-Volatile
and Volatile
R/W
Output Driver Strength:
Output Drive Strength can be selected according to Table 6.14
EB6
EB7
ODS1
ODS2
R/W
R/W
Table 6.14 Driver Strength Table
ODS2
ODS1
ODS0
Description
Reserved
12.50%
25%
Remark
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
37.50%
Reserved
75%
100%
50%
Default
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
19
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
WIP bit: The definition of the WIP bit is exactly same as the one of Status Register.
PROT_E bit: The Protection Error bit indicates whether an Erase or Program operation has attempted to modify a
protected array sector or block, or to access a locked Information Row region. When the bit is set to “1” it indicates
that there was an error or errors in previous Erase or Program operations. See Table 6.15 for details.
P_ERR bit: The Program Error bit indicates whether a Program operation has succeeded or failed, or whether a
Program operation has attempted to program a protected array sector/block or a locked Information Row region.
When the bit is set to “1” it indicates that there was an error or errors in previous Program or Write/Set Non-Volatile
Register operations. See Table 6.15 for details.
E_ERR bit: The Erase Error bit indicates whether an Erase operation has succeeded or failed, or whether an Erase
operation has attempted to erase a protected array sector/block or a locked Information Row region. When the bit
is set to “1” it indicates that there was an error or errors in previous Erase or Write/Set Non-Volatile Register
operations. See Table 6.15 for details.
Table 6.15 Instructions to set PROT_E, P_ERR, or E_ERR bit
Instructions
Description
The commands will set the P_ERR if there is a failure in the operation. Attempting to program
within the protected array sector/block or within an erase suspended sector/block will result in
a programming error with P_ERR and PROT_E set to “1”.
PP/PPQ
IRP
The command will set the P_ERR if there is a failure in the operation. In attempting to program
within a locked Information Row region, the operation will fail with P_ERR and PROT_E set to
1.
The update process for the non-volatile register bits involves an erase and a program operation
on the non-volatile register bits. If either the erase or program portion of the update fails, the
related error bit (P_ERR or E_ERR) will be set to “1”.
Only for WRSR command, when Status Register is write-protected by SRWD bit and WP# pin,
attempting to write the register will set PROT_E and E_ERR to “1”.
WRSR/WRABR/SRPNV/
SERPNV
WRFR
The commands will set the P_ERR if there is a failure in the operation.
The commands will set the E_ERR if there is a failure in the operation. E_ERR and PROT_E
SER/BER32K/BER64K/CER/ will be set to “1” when the user attempts to erase a protected main memory sector/block or a
IRER
locked Information Row region. Chip Erase (CER) command will set E_ERR and PROT_E if
any Block Protection bits (BP3~BP0) are not 0. .
Notes:
1. OTP bits in the Function Register may only be programmed to “1”. Writing of the bits back to “0” is ignored and no
error is set.
2. Read only bits in registers are never modified by a command so that the corresponding bits in the Write/Set Register
command data byte are ignored without setting any error indication.
3. Once the PROT_E, P_ERR, and E_ERR error bits are set to “1”, they remains set to “1” until they are cleared to “0”
with a Clear Extended Read Register (CLERP) command. This means that those error bits must be cleared through
the CLERP command. Alternatively, Hardware Reset, or Software Reset may be used to clear the bits.
4. Any further command will be executed even though the error bits are set to “1”.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
20
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
6.4 AUTOBOOT REGISTER
AutoBoot Register Bit (32 bits) Definitions are described in Table 6.15.
Table 6.16 AutoBoot Register Parameter Bit Table
Default
Bits
Symbols
Function
Type
Description
Value
AB[31:24]
AB[23:5]
ABSA
Reserved
Reserved
00h
Reserved for future use
AutoBoot Start
Address
Non-
Volatile
32 byte boundary address for the start of boot code
access
ABSA
00000h
Number of initial delay cycles between CE# going
low and the first bit of boot code being transferred,
and it is the same as dummy cycles of FRD (QE=0)
or FRQIO (QE=1).
Example: The number of initial delay cycles is 8
(QE=0) or 6 (QE=1) when AB[4:1]=0h (Default
setting).
AutoBoot Start
Delay
Non-
Volatile
AB[4:1]
AB0
ABSD
ABE
0h
0
AutoBoot
Enable
Non-
Volatile
1 = AutoBoot is enabled
0 = AutoBoot is not enabled
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
21
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
7. PROTECTION MODE
The device supports hardware and software write-protection mechanisms.
7.1 HARDWARE WRITE PROTECTION
The Write Protection (WP#) pin provides a hardware write protection method for BP3, BP2, BP1, BP0, SRWD, and
QE in the Status Register. Refer to the section 6.1 STATUS REGISTER.
Write inhibit voltage (VWI) is specified in the section 9.8 POWER-UP AND POWER-DOWN. All write sequence will
be ignored when Vcc drops to VWI.
Table 7.1 Hardware Write Protection on Status Register
SRWD
WP#
Low
Low
High
High
Status Register
Writable
0
1
0
1
Protected
Writable
Writable
Note: Before the execution of any program, erase or write Status Register instruction, the Write Enable Latch (WEL)
bit must be enabled by executing a Write Enable (WREN) instruction. If the WEL bit is not enabled, the program,
erase or write register instruction will be ignored.
7.2 SOFTWARE WRITE PROTECTION
The device also provides a software write protection feature. The Block Protection (BP3, BP2, BP1, BP0) bits allow
part or the whole memory area to be write-protected.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
22
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8. DEVICE OPERATION
The device utilizes an 8-bit instruction register. Refer to Table 8.1. Instruction Set for details on instructions and
instruction codes. All instructions, addresses, and data are shifted in with the most significant bit (MSB) first on
Serial Data Input (SI) or Serial Data IOs (IO0, IO1, IO2, IO3). The input data on SI or IOs is latched on the rising
edge of Serial Clock (SCK) for normal mode and both of rising and falling edges for DTR mode after Chip Enable
(CE#) is driven low (VIL). Every instruction sequence starts with a one-byte instruction code and is followed by
address bytes, data bytes, or both address bytes and data bytes, depending on the type of instruction. CE# must
be driven high (VIH) after the last bit of the instruction sequence has been shifted in to end the operation.
Table 8.1 Instruction Set
Instruction
Operation
Mode
Byte0
Byte1
Byte2
Byte3
Byte4
Byte5
Byte6
Name
NORD
FRD
Normal Read
Mode
A
A
A
<7:0>
SPI
03h
0Bh
Data out
<23:16>
<15:8>
Fast Read
Mode
SPI
QPI
A
A
A
<7:0>
Dummy(1)
Byte
Data out
<23:16>
<15:8>
A
A
A
<7:0>
Dual
Fast Read
Dual I/O
AXh(1),(2)
Dual
Dual
Data out
FRDIO
FRDO
FRQIO
SPI
SPI
BBh
3Bh
EBh
<23:16>
Dual
<15:8>
Dual
Fast Read
Dual Output
A
A
A
<7:0>
Dummy(1)
Byte
Dual
Data out
<23:16>
<15:8>
A
A
A
<7:0>
Quad
Fast Read
Quad I/O
SPI
QPI
AXh(1), (2)
Quad
Quad
Data out
<23:16>
Quad
<15:8>
Quad
Fast Read
Quad Output
A
A
A
<7:0>
Dummy(1)
Byte
Quad
Data out
FRQO
SPI
6Bh
0Dh
<23:16>
<15:8>
Fast Read
DTR Mode
SPI
QPI
A
A
A
<7:0>
Dummy(1)
Byte
Dual
Data out
FRDTR
<23:16>
<15:8>
A
A
A
<7:0>
Dual
Fast Read
Dual I/O DTR
AXh(1), (2)
Dual
Dual
Data out
FRDDTR
SPI
BDh
<23:16>
Dual
<15:8>
Dual
Fast Read
Quad I/O DTR
SPI
QPI
A
A
A
<7:0>
AXh(1), (2)
Quad
Quad
Data out
FRQDTR
PP
EDh
02h
<23:16>
<15:8>
Input Page
Program
SPI
QPI
A
A
A
<7:0>
PD
(256byte)
<23:16>
<15:8>
Quad Input
Page Program
32h
38h
A
A
A
<7:0>
Quad PD
(256byte)
PPQ
SPI
<23:16>
<15:8>
SPI
QPI
D7h
20h
A
A
A
<7:0>
SER
Sector Erase
<23:16>
<15:8>
BER32
(32KB)
Block Erase
32Kbyte
SPI
QPI
A
A
A
<7:0>
52h
D8h
<23:16>
<15:8>
BER64
(64KB)
Block Erase
64Kbyte
SPI
QPI
A
A
A
<7:0>
<23:16>
<15:8>
SPI
QPI
C7h
60h
CER
WREN
WRDI
RDSR
WRSR
Chip Erase
Write Enable
Write Disable
SPI
QPI
06h
04h
05h
01h
SPI
QPI
Read Status
Register
SPI
QPI
SR
Write Status
Register
SPI
QPI
WSR
Data
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
23
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Instruction
Name
Operation
Mode
Byte0
Byte1
Byte2
Byte3
Byte4
Byte5
Byte6
Read Function
Register
SPI
QPI
Data
out
RDFR
WRFR
QPIEN
QPIDI
48h
42h
35h
F5h
Write Function
Register
SPI
QPI
WFR
Data
Enter
QPI mode
SPI
QPI
Exit
QPI mode
Suspend during
program/erase
SPI
QPI
75h
B0h
PERSUS
PERRSM
DP
Resume
program/erase
SPI
QPI
7Ah
30h
Deep Power
Down
SPI
QPI
B9h
ABh
Read ID /
Release
Power Down
RDID,
RDPD
SPI
QPI
XXh(3)
Data in
Data in
XXh(3)
XXh(3)
ID7-ID0
Set Read
SPI
QPI
SRPNV
SRPV
Parameters
(Non-Volatile)
Set Read
Parameters
(Volatile)
65h
SPI
QPI
C0h
63h
Set Extended
Read
Parameters
(Non-Volatile)
Set Extended
Read
SPI
QPI
SERPNV
SERPV
85h
83h
Data in
Data in
SPI
QPI
Parameters
(Volatile)
Read Read
Parameters
(Volatile)
Read Extended
Read Parameters
(Volatile)
SPI
QPI
RDRP
61h
81h
Data out
Data out
SPI
QPI
RDERP
Clear Extended
Read Register
SPI
QPI
CLERP
82h
9Fh
Read JEDEC
ID Command
SPI
QPI
RDJDID
MF7-MF0
XXh(3)
ID15-ID8
XXh(3)
ID7-ID0
00h
01h
MF7-MF0
ID7-ID0
ID7-ID0
Read
Manufacturer
& Device ID
SPI
QPI
RDMDID
90h
AFh
MF7-MF0
Read JEDEC
ID
RDJDIDQ
QPI
MF7-MF0
ID15-ID8
ID7-ID0
QPI mode
Read
Unique ID
SPI
QPI
A(4)
<23:16>
A(4)
<15:8>
A(4)
<7:0>
Dummy
Byte
RDUID
RDSFDP
NOP
4Bh
5Ah
00h
Data out
Data out
SPI
QPI
A
A
A
<7:0>
Dummy
Byte
SFDP Read
<23:16>
<15:8>
SPI
QPI
No Operation
Software
Reset
Enable
SPI
QPI
RSTEN
RST
66h
99h
SPI
QPI
Software Reset
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
24
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Instruction
Name
Operation
Mode
Byte0
Byte1
Byte2
Byte3
Byte4
Byte5
Byte6
Erase
Information
Row
Program
Information
Row
Read
Information
Row
SPI
QPI
A
A
A
<7:0>
IRER
IRP
64h
62h
68h
<23:16>
<15:8>
SPI
QPI
A
A
A
<7:0>
PD
(256byte)
<23:16>
<15:8>
SPI
QPI
A
A
A
<7:0>
Dummy
Byte
IRRD
Data out
<23:16>
<15:8>
SECUN-
LOCK
SPI
QPI
A
A
A
<7:0>
Sector Unlock
Sector Lock
26h
24h
14h
15h
<23:16>
<15:8>
SPI
QPI
SECLOCK
RDABR
Read AutoBoot
Register
SPI
QPI
Write AutoBoot
Register
SPI
QPI
WRABR
Data in 1
Data in 2
Data in 3
Data in 4
Notes:
1. The number of dummy cycles depends on the value setting in the Table 6.11 Read Dummy Cycles.
2. AXh has to be counted as a part of dummy cycles. X means “don’t care”.
3. XX means “don’t care”.
4. A<23:9> are “don’t care” and A<8:4> are always “0”.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
25
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.1 NORMAL READ OPERATION (NORD, 03h)
The NORMAL READ (NORD) instruction is used to read memory contents at a maximum frequency of 50MHz.
The NORD instruction code is transmitted via the SI line, followed by three address bytes (A23 - A0) of the first
memory location to be read. A total of 24 address bits are shifted in, but only AVMSB (Valid Most Significant Bit) - A0
are decoded. The remaining bits (A23 – AVMSB+1) are ignored. The first byte addressed can be at any memory
location. Upon completion, any data on the SI will be ignored. Refer to Table 8.2 for the related Address Key.
The first byte data (D7 - D0) is shifted out on the SO line, MSB first. A single byte of data, or up to the whole memory
array, can be read out in one NORMAL READ instruction. The address is automatically incremented by one after
each byte of data is shifted out. The read operation can be terminated at any time by driving CE# high (VIH) after
the data comes out. When the highest address of the device is reached, the address counter will roll over to the
000000h address, allowing the entire memory to be read in one continuous READ instruction.
If the NORMAL READ instruction is issued while an Erase, Program or Write operation is in process (WIP=1) the
instruction is ignored and will not have any effects on the current operation.
Table 8.2 Address Key
Address
8Mb
4Mb
2Mb
AVMSB–A0
A19-A0 (A23-A20=X)
A18-A0 (A23-A19=X)
A17-A0 (A23-A18=X)
Note: X=Don’t Care
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
26
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.1 Normal Read Sequence
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
...
SI
3
Instruction = 03h
2
1
0
23
22
High Impedance
SO
CE#
SCK
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
...
SI
Data Out 1
Data Out 2
SO
...
1
0
1
0
3
6
5
4
3
2
7
6
5
4
2
7
tV
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
27
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.2 FAST READ OPERATION (FRD, 0Bh)
The FAST READ (FRD) instruction is used to read memory data at up to a 133MHz clock.
The FAST READ instruction code is followed by three address bytes (A23 - A0) and dummy cycles (configurable,
default is 8 clocks), transmitted via the SI line, with each bit latched-in during the rising edge of SCK. Then the first
data byte from the address is shifted out on the SO line, with each bit shifted out at a maximum frequency fCT,
during the falling edge of SCK.
The first byte addressed can be at any memory location. The address is automatically incremented by one after
each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the
000000h address, allowing the entire memory to be read with a single FAST READ instruction. The FAST READ
instruction is terminated by driving CE# high (VIH).
If the FAST READ instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction
is ignored without affecting the current cycle.
Figure 8.2 Fast Read Sequence
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
SI
3-byte Address
...
3
Instruction = 0Bh
2
1
0
23
22
High Impedance
SO
CE#
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
...
SCK
SI
Dummy Cycles
Data Out
tV
SO
...
1
0
3
7
6
5
4
2
Note: Dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
28
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
FAST READ OPERATION IN QPI MODE (FRD, 0Bh)
The FAST READ (FRD) instruction is used also in QPI mode to read memory data at up to a 133MHz clock.
The FAST READ instruction code (2 clocks) is followed by three address bytes (A23-A0 — 6 clocks) and dummy
cycles (configurable, default is 6 cycles), transmitted via the IO3, IO2, IO1 and IO0 lines, with each bit latched-in
during the rising edge of SCK. Then the first data byte addressed is shifted out on the IO3, IO2, IO1 and IO0 lines,
with each bit shifted out at a maximum frequency fCT, during the falling edge of SCK.
The first byte addressed can be at any memory location. The address is automatically incremented by one after
each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the
000000h address, allowing the entire memory to be read with a single FAST READ instruction. The FAST READ
instruction in QPI mode is terminated by driving CE# high (VIH).
If the FAST READ instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction
is ignored without affecting the current cycle.
The Fast Read sequence in QPI mode is also applied to the commands in the following table 8.3.
Table 8.3 Address Key
Instruction Name
Operation
Hex Code
EBh
FRQIO
Fast Read Quad I/O
RDUID
Read Unique ID
4Bh
IRRD
Read Information Row
68h
Figure 8.3 Fast Read Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
...
13
14
15
16
17
...
Mode 3
Mode 0
SCK
tV
...
IO[3:0]
0Bh
Instruction
23:20 19:16 15:12 11:8 7:4 3:0
3-byte Address
7:4 3:0
Data 1
7:4 3:0
Data 2
6 Dummy Cycles
Note: Number of dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy
Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
29
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.3 HOLD OPERATION
HOLD# is used in conjunction with CE# to select the device. When the device is selected and a serial sequence is
underway, HOLD# can be used to pause the serial communication with the master device without resetting the
serial sequence. To pause, HOLD# is brought low while the SCK signal is low. To resume serial communication,
HOLD# is brought high while the SCK signal is low (SCK may still toggle during HOLD). Inputs to SI will be ignored
while SO is in the high impedance state, during HOLD.
Note: HOLD is not supported in DTR mode or with QE=1 or when RESET# is selected for the HOLD# or RESET# pin.
Timing graph can be referenced in AC Parameters Figure 9.4.
8.4 FAST READ DUAL I/O OPERATION (FRDIO, BBh)
The FRDIO allows the address bits to be input two bits at a time. This may allow for code to be executed directly
from the SPI in some applications.
The FRDIO instruction code is followed by three address bytes (A23 – A0) and dummy cycles (configurable, default
is 4 clocks), transmitted via the IO1 and IO0 lines, with each pair of bits latched-in during the rising edge of SCK.
The address MSB is input on IO1, the next bit on IO0, and this shift pattern continues to alternate between the two
lines. Depending on the usage of AX read operation mode, a mode byte may be located after address input.
The first data byte addressed is shifted out on the IO1 and IO0 lines, with each pair of bits shifted out at a maximum
frequency fCT, during the falling edge of SCK. The MSB is output on IO1, while simultaneously the second bit is
output on IO0. Figure 8.4 illustrates the timing sequence.
The first byte addressed can be at any memory location. The address is automatically incremented by one after
each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the
000000h address, allowing the entire memory to be read with a single FRDIO instruction. FRDIO instruction is
terminated by driving CE# high (VIH).
The device supports the AX read operation by applying mode bits during dummy period. Mode bits consist of 8
bits, such as M7 to M0. Four cycles after address input are reserved for Mode bits in FRDIO execution. M7 to M4
are important for enabling this mode. M3 to M0 become don’t care for future use. When M[7:4]=1010(Ah), it enables
the AX read operation and subsequent FRDIO execution skips command code. It saves cycles as described in
Figure 8.5. When the code is different from AXh (where X is don’t care), the device exits the AX read operation.
After finishing the read operation, device becomes ready to receive a new command. SPI or QPI mode configuration
retains the prior setting. Mode bit must be applied during dummy cycles. Number of dummy cycles in Table 6.11
includes number of mode bit cycles. If dummy cycles are configured as 4 cycles, data output will start right after
mode bit is applied.
If the FRDIO instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is
ignored and will not affect the current cycle.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
30
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.4 Fast Read Dual I/O Sequence (with command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
...
18
19
20
21
Mode 3
Mode 0
SCK
4 Dummy Cycles
3-byte Address
...
IO0
IO1
2
3
Instruction = BBh
0
1
6
7
4
22
23
20
21
18
High Impedance
...
5
19
Mode Bits
CE#
SCK
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
...
tV
...
...
IO0
2
0
1
4
5
0
1
2
0
1
6
7
2
6
7
6
7
6
7
4
2
0
1
4
4
Data Out 1
Data Out 2
Data Out 3
IO1
3
5
3
3
5
3
5
Mode Bits
Notes:
1. If the mode bits=AXh (where X is don’t care), it can execute the AX read mode (without command). When the mode
bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
31
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.5 Fast Read Dual I/O AX Read Sequence (without command decode cycles)
CE#
...
0
1
2
3
11
12
13
14
15
16
17
18
19
20
21
...
Mode 3
Mode 0
SCK
4 Dummy Cycles
tV
3-byte Address
Data Out 1
Data Out 2
4
...
...
IO0
IO1
2
3
6
7
2
6
7
2
0
1
4
0
1
4
0
1
6
7
22
23
20
21
18
...
...
3
3
5
5
5
19
Mode Bits
Notes:
1. If the mode bits=AXh (where X is don’t care), it will keep executing the AX read mode (without command). When the
mode bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
32
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.5 FAST READ DUAL OUTPUT OPERATION (FRDO, 3Bh)
The FRDO instruction is used to read memory data on two output pins each at up to a 133MHz clock.
The FRDO instruction code is followed by three address bytes (A23 – A0) and dummy cycles (configurable, default
is 8 clocks), transmitted via the IO0 line, with each bit latched-in during the rising edge of SCK. Then the first data
byte addressed is shifted out on the IO1 and IO0 lines, with each pair of bits shifted out at a maximum frequency
fCT, during the falling edge of SCK. The first bit (MSB) is output on IO1. Simultaneously, the second bit is output
on IO0.
The first byte addressed can be at any memory location. The address is automatically incremented by one after
each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the
000000h address, allowing the entire memory to be read with a single FRDO instruction. The FRDO instruction is
terminated by driving CE# high (VIH).
If the FRDO instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is
ignored and will not have any effects on the current cycle.
Figure 8.6 Fast Read Dual Output Sequence
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
...
3
IO0
IO1
Instruction = 3Bh
2
1
0
23
22
High Impedance
CE#
SCK
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
...
tV
...
...
IO0
IO1
0
1
2
6
7
4
6
7
4
2
0
1
8 Dummy Cycles
Data Out 1
Data Out 2
3
5
5
3
Note: Dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
33
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.6 FAST READ QUAD OUTPUT OPERATION (FRQO, 6Bh)
The FRQO instruction is used to read memory data on four output pins each at up to a 133 MHz clock.
The FRQO instruction code is followed by three address bytes (A23 – A0) and dummy cycles (configurable,
default is 8 clocks), transmitted via the IO0 line, with each bit latched-in during the rising edge of SCK. Then the
first data byte addressed is shifted out on the IO3, IO2, IO1 and IO0 lines, with each group of four bits shifted
out at a maximum frequency fCT, during the falling edge of SCK. The first bit (MSB) is output on IO3, while
simultaneously the second bit is output on IO2, the third bit is output on IO1, etc.
The first byte addressed can be at any memory location. The address is automatically incremented after each
byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h
address, allowing the entire memory to be read with a single FRQO instruction. FRQO instruction is terminated
by driving CE# high (VIH).
If a FRQO instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is
ignored and will not have any effects on the current cycle.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
34
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.7 Fast Read Quad Output Sequence
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
IO0
3-byte Address
...
3
Instruction = 6Bh
2
1
0
23
22
High Impedance
IO1
IO2
IO3
High Impedance
High Impedance
CE#
SCK
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
...
tV
...
IO0
IO1
IO2
IO3
0
4
4
0
4
0
4
0
8 Dummy Cycles
Data Out 1 Data Out 2 Data Out 3 Data Out 4
1
...
...
5
5
1
5
1
5
1
2
6
6
2
6
2
6
2
3
...
7
7
3
7
3
7
3
Note: Dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
35
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.7 FAST READ QUAD I/O OPERATION (FRQIO, EBh)
The FRQIO instruction allows the address bits to be input four bits at a time. This may allow for code to be executed
directly from the SPI in some applications.
The FRQIO instruction code is followed by three address bytes (A23 – A0) and dummy cycles (configurable, default
is 6 clocks), transmitted via the IO3, IO2, IO1 and IO0 lines, with each group of four bits latched-in during the rising
edge of SCK. The address of MSB inputs on IO3, the next bit on IO2, the next bit on IO1, the next bit on IO0, and
continue to shift in alternating on the four. Depending on the usage of AX read operation mode, a mode byte may
be located after address input.
The first data byte addressed is shifted out on the IO3, IO2, IO1 and IO0 lines, with each group of four bits shifted
out at a maximum frequency fCT, during the falling edge of SCK. The first bit (MSB) is output on IO3, while
simultaneously the second bit is output on IO2, the third bit is output on IO1, etc. Figure 8.8 illustrates the timing
sequence.
The first byte addressed can be at any memory location. The address is automatically incremented after each byte
of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h
address, allowing the entire memory to be read with a single FRQIO instruction. FRQIO instruction is terminated
by driving CE# high (VIH).
The device supports the AX read operation by applying mode bits during dummy period. Mode bits consist of 8
bits, such as M7 to M0. Two cycles after address input are reserved for Mode bits in FRQIO execution. M7 to M4
are important for enabling this mode. M3 to M0 become don’t care for future use. When M[7:4]=1010(Ah), it enables
the AX read operation and subsequent FRQIO execution skips command code. It saves cycles as described in
Figure 8.9. When the code is different from AXh (where X is don’t care), the device exits the AX read operation.
After finishing the read operation, device becomes ready to receive a new command. SPI or QPI mode configuration
retains the prior setting. Mode bit must be applied during dummy cycles. Number of dummy cycles in Table 6.11
includes number of mode bit cycles. If dummy cycles are configured as 6 cycles, data output will start right after
mode bits and 4 additional dummy cycles are applied.
If the FRQIO instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is
ignored and will not have any effects on the current cycle.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
36
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.8 Fast Read Quad I/O Sequence (with command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
3-byte Address
IO0
IO1
4
5
6
7
Instruction = EBh
High Impedance
0
1
2
3
4
5
6
7
0
1
2
3
20
21
22
23
16
17
18
19
12
13
14
15
8
9
IO2
IO3
10
11
Mode Bits
CE#
SCK
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
...
6 Dummy Cycles
Data Out 1 Data Out 2 Data Out 3 Data Out 4
Data Out 5 Data Out 6
tV
...
...
...
...
IO0
0
1
2
3
4
5
6
7
4
5
6
7
4
5
6
7
0
1
2
3
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
4
5
6
7
0
1
2
3
0
1
2
3
IO1
IO2
IO3
Notes:
1. If the mode bits=AXh (where X is don’t care), it can execute the AX read mode (without command). When the mode
bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
37
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.9 Fast Read Quad I/O AX Read Sequence (without command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
...
Mode 3
Mode 0
SCK
6 Dummy Cycles
3-byte Address
Data Out 1 Data Out 2
tV
...
...
...
...
IO0
IO1
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
0
1
2
3
4
5
6
7
4
5
6
7
20
21
22
23
16
17
18
19
12
13
14
15
8
9
0
1
2
3
IO2
IO3
10
11
Mode Bits
Notes:
1. If the mode bits=AXh (where X is don’t care), it will keep executing the AX read mode (without command). When the
mode bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
38
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
FAST READ QUAD I/O OPERATION IN QPI MODE (FRQIO, EBh)
The FRQIO instruction is also used in QPI mode to read memory data at up to a 133MHz clock.
The FRQIO instruction in QPI mode utilizes all four IO lines to input the instruction code so that only two clocks are
required, while the FRQIO instruction in SPI mode requires that the byte-long instruction code is shifted into the
device only via IO0 line in eight clocks. As a result, 6 command cycles will be reduced by the FRQIO instruction in
QPI mode. In addition, subsequent address and data out are shifted in/out via all four IO lines like the FRQIO
instruction. In fact, except for the command cycle, the FRQIO operation in QPI mode is exactly same as the FRQIO
operation in SPI mode.
The device supports the AX read operation by applying mode bits during dummy period. Mode bits consist of 8
bits, such as M7 to M0. Two cycles after address input are reserved for Mode bits in FRQIO execution. M7 to M4
are important for enabling this mode. M3 to M0 become don’t care for future use. When M[7:4]=1010(Ah), it enables
the AX read operation and subsequent FRQIO execution skips command code. It saves cycles as described in
Figure 8.9. When the code is different from AXh (where X is don’t care), the device exits the AX read operation.
After finishing the read operation, device becomes ready to receive a new command. SPI or QPI mode configuration
retains the prior setting. Mode bit must be applied during dummy cycles. Number of dummy cycles in Table 6.11
includes number of mode bit cycles. If dummy cycles are configured as 6 cycles, data output will start right after
mode bits and 4 additional dummy cycles are applied.
If the FRQIO instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is
ignored and will not have any effects on the current cycle.
Figure 8.10 Fast Read Quad I/O Sequence in QPI Mode
CE#
...
0
1
2
3
4
5
6
7
8
9
13
14
15
16
17
...
Mode 3
Mode 0
SCK
tV
Mode Bits
7:4 3:0
...
IO[3:0]
23:20 19:16 15:12 11:8 7:4 3:0
3-byte Address
EBh
Instruction
7:4 3:0
Data 1
7:4 3:0
Data 2
6 Dummy Cycles
Note: Number of dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy
Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
39
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.8 PAGE PROGRAM OPERATION (PP, 02h)
The Page Program (PP) instruction allows up to 256 bytes data to be programmed into memory in a single
operation. The destination of the memory to be programmed must be outside the protected memory area set by
the Block Protection (BP3, BP2, BP1, BP0) bits. A PP instruction which attempts to program into a page that is
write-protected will be ignored. Before the execution of PP instruction, the Write Enable Latch (WEL) must be
enabled through a Write Enable (WREN) instruction.
The PP instruction code, three address bytes and program data (1 to 256 bytes) are input via the Sl line. Program
operation will start immediately after the CE# is brought high, otherwise the PP instruction will not be executed.
The internal control logic automatically handles the programming voltages and timing. During a program operation,
all instructions will be ignored except the RDSR instruction. The progress or completion of the program operation
can be determined by reading the WIP bit in Status Register via a RDSR instruction. If the WIP bit is “1”, the
program operation is still in progress. If WIP bit is “0”, the program operation has completed.
If more than 256 bytes data are sent to a device, the address counter rolls over within the same page, the previously
latched data are discarded, and the last 256 bytes are kept to be programmed into the page. The starting byte can
be anywhere within the page. When the end of the page is reached, the address will wrap around to the beginning
of the same page. If the data to be programmed are less than a full page, the data of all other bytes on the same
page will remain unchanged.
Note: A program operation can alter “1”s into “0”s. The same byte location or page may be programmed more than
once, to incrementally change “1”s to “0”s. An erase operation is required to change “0”s to “1”s.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
40
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.11 Page Program Sequence in SPI Mode
CE#
0
1
...
7
8
9
...
31
32
33
...
39
...
...
...
Mode 3
Mode 0
SCK
3-byte Address
Data In 1
Data In 256
SI
...
...
6
...
0
7
0
0
Instruction = 02h
7
23
22
High Impedance
SO
Figure 8.12 Page Program Sequence in QPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
...
...
Mode 3
Mode 0
SCK
02h
23:20 19:16 15:12 11:8 7:4 3:0
3-byte Address
7:4 3:0
Data In 1
7:4 3:0 7:4 3:0
Data In 2 Data In 3
7:4 3:0
Data In 4
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
41
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.9 QUAD INPUT PAGE PROGRAM OPERATION (PPQ, 32h/38h)
The Quad Input Page Program instruction allows up to 256 bytes data to be programmed into memory in a single
operation with four pins (IO0, IO1, IO2 and IO3). The destination of the memory to be programmed must be outside
the protected memory area set by the Block Protection (BP3, BP2, BP1, BP0) bits. A Quad Input Page Program
instruction which attempts to program into a page that is write-protected will be ignored. Before the execution of
Quad Input Page Program instruction, the QE bit in the Status Register must be set to “1” and the Write Enable
Latch (WEL) must be enabled through a Write Enable (WREN) instruction.
The Quad Input Page Program instruction code, three address bytes and program data (1 to 256 bytes) are input
via the four pins (IO0, IO1, IO2 and IO3). Program operation will start immediately after the CE# is brought high,
otherwise the Quad Input Page Program instruction will not be executed. The internal control logic automatically
handles the programming voltages and timing. During a program operation, all instructions will be ignored except
the RDSR instruction. The progress or completion of the program operation can be determined by reading the WIP
bit in Status Register via a RDSR instruction. If the WIP bit is “1”, the program operation is still in progress. If WIP
bit is “0”, the program operation has completed.
If more than 256 bytes data are sent to a device, the address counter rolls over within the same page, the previously
latched data are discarded, and the last 256 bytes data are kept to be programmed into the page. The starting byte
can be anywhere within the page. When the end of the page is reached, the address will wrap around to the
beginning of the same page. If the data to be programmed are less than a full page, the data of all other bytes on
the same page will remain unchanged.
Note: A program operation can alter “1”s into “0”s. The same byte location or page may be programmed more than
once, to incrementally change “1”s to “0”s. An erase operation is required to change “0”s to “1”s.
Figure 8.13 Quad Input Page Program Sequence
CE#
0
1
2
3
4
5
6
7
8
9
...
31
32
33
34
35
...
Mode 3
Mode 0
SCK
3-byte Address
Data In 1
Data In 2
...
...
...
...
IO0
IO1
...
4
5
6
7
Instruction = 32h/38h
High Impedance
0
1
2
3
4
5
6
7
0
1
2
3
23
22
0
IO2
IO3
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
42
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.10 ERASE OPERATION
The Erase command sets all bits in the addressed sector or block to “1”s.
The memory array of the device is organized into uniform 4 Kbyte sectors or 32/64 Kbyte uniform blocks (a block
consists of eight/sixteen adjacent sectors respectively).
Before a byte is reprogrammed, the sector or block that contains the byte must be erased (erasing sets bits to “1”).
In order to erase the device, there are three erase instructions available: Sector Erase (SER), Block Erase (BER)
and Chip Erase (CER). A sector erase operation allows any individual sector to be erased without affecting the
data in other sectors. A block erase operation erases any individual block. A chip erase operation erases the whole
memory array of a device. A sector erase, block erase, or chip erase operation can be executed prior to any
programming operation.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
43
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.11 SECTOR ERASE OPERATION (SER, D7h/20h)
A Sector Erase (SER) instruction erases a 4 Kbyte sector before the execution of a SER instruction, the Write
Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL bit is automatically reset after
the completion of Sector Erase operation.
A SER instruction is entered, after CE# is pulled low to select the device and stays low during the entire instruction
sequence The SER instruction code, and three address bytes are input via SI. Erase operation will start immediately
after CE# is pulled high. The internal control logic automatically handles the erase voltage and timing.
During an erase operation, all instruction will be ignored except the Read Status Register (RDSR) instruction. The
progress or completion of the erase operation can be determined by reading the WIP bit in the Status Register
using a RDSR instruction.
If the WIP bit is “1”, the erase operation is still in progress. If the WIP bit is “0”, the erase operation has been
completed.
Figure 8.14 Sector Erase Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
...
SI
3
Instruction = D7h/20h
2
1
0
23
22
High Impedance
SO
Figure 8.15 Sector Erase Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
3-byte Address
23:20 19:16 15:12 11:8 7:4 3:0
D7h/20h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
44
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.12 BLOCK ERASE OPERATION (BER32K:52h, BER64K:D8h)
A Block Erase (BER) instruction erases a 32/64Kbyte block. Before the execution of a BER instruction, the Write
Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL is reset automatically after the
completion of a block erase operation.
The BER instruction code and three address bytes are input via SI. Erase operation will start immediately after the
CE# is pulled high, otherwise the BER instruction will not be executed. The internal control logic automatically
handles the erase voltage and timing.
Figure 8.16 Block Erase (64K) Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
...
SI
3
Instruction = D8h
2
1
0
23
22
High Impedance
SO
Figure 8.17 Block Erase (64K) Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
3-byte Address
23:20 19:16 15:12 11:8 7:4 3:0
D8h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
45
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.18 Block Erase (32K) Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
SI
...
3
Instruction = 52h
2
1
0
23
22
High Impedance
SO
Figure 8.19 Block Erase (32K) Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
3-byte Address
23:20 19:16 15:12 11:8 7:4 3:0
52h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
46
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.13 CHIP ERASE OPERATION (CER, C7h/60h)
A Chip Erase (CER) instruction erases the entire memory array. Before the execution of CER instruction, the Write
Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL is automatically reset after
completion of a chip erase operation.
The CER instruction code is input via the SI. Erase operation will start immediately after CE# is pulled high,
otherwise the CER instruction will not be executed. The internal control logic automatically handles the erase
voltage and timing.
Chip Erase (CER) instruction can be executed only when Block Protection (BP3~BP0) bits are set to 0s. If the BP
bits are not 0, the CER command is not executed and E_ERR and PROT_E are set.
Figure 8.20 Chip Erase Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction = C7h/60h
High Impedance
SI
SO
Figure 8.21 Chip Erase Sequence In QPI Mode
CE#
0
1
Mode 3
SCK
Mode 0
C7h/60h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
47
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.14 WRITE ENABLE OPERATION (WREN, 06h)
The Write Enable (WREN) instruction is used to set the Write Enable Latch (WEL) bit. The WEL bit is reset to the
write-protected state after power-up. The WEL bit must be write enabled before any write operation, including
Sector Erase, Block Erase, Chip Erase, Page Program, Program Information Row, Write Status Register, Write
Function Register, Set non-volatile Read Register, Set non-volatile Extended Read Register, and Write Autoboot
Register operations except for Set volatile Read Register and Set volatile Extended Read Register. The WEL bit
will be reset to the write-protected state automatically upon completion of a write operation. The WREN instruction
is required before any above operation is executed.
Figure 8.22 Write Enable Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction = 06h
SI
High Impedance
SO
Figure 8.23 Write Enable Sequence In QPI Mode
CE#
0
1
Mode 3
SCK
Mode 0
06h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
48
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.15 WRITE DISABLE OPERATION (WRDI, 04h)
The Write Disable (WRDI) instruction resets the WEL bit and disables all write instructions. The WRDI instruction
is not required after the execution of a write instruction, since the WEL bit is automatically reset.
Figure 8.24 Write Disable Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction = 04h
SI
High Impedance
SO
Figure 8.25 Write Disable Sequence In QPI Mode
CE#
0
1
Mode 3
SCK
Mode 0
04h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
49
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.16 READ STATUS REGISTER OPERATION (RDSR, 05h)
The Read Status Register (RDSR) instruction provides access to the Status Register. During the execution of a
program, erase or write Status Register operation, all other instructions will be ignored except the RDSR instruction,
which can be used to check the progress or completion of an operation by reading the WIP bit of Status Register.
Figure 8.26 Read Status Register Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
SI
Instruction = 05h
tV
Data Out
SO
3
2
1
0
7
6
5
4
Figure 8.27 Read Status Register Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
tV
IO[3:0]
05h
7:4 3:0
Data Out
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
50
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.17 WRITE STATUS REGISTER OPERATION (WRSR, 01h)
The Write Status Register (WRSR) instruction allows the user to enable or disable the block protection and Status
Register write protection features by writing “0”s or “1”s into the non-volatile BP3, BP2, BP1, BP0, and SRWD bits.
Also WRSR instruction allows the user to disable or enable quad operation by writing “0” or “1” into the non-volatile
QE bit.
Figure 8.28 Write Status Register Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
7
9
6
10
11
12
13
14
15
Mode 3
Mode 0
SCK
Data In
SI
Instruction = 01h
2
1
0
3
5
4
High Impedence
SO
Figure 8.29 Write Status Register Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
IO[3:0]
01h
7:4 3:0
Data In
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
51
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.18 READ FUNCTION REGISTER OPERATION (RDFR, 48h)
The Read Function Register (RDFR) instruction provides access to the Function Register. Refer to Table 6.6
Function Register Bit Definition for more detail.
Figure 8.30 Read Function Register Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
SI
Instruction = 48h
tV
Data Out
SO
3
2
1
0
7
6
5
4
Figure 8.31 Read Function Register Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
tV
IO[3:0]
48h
7:4 3:0
Data Out
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
52
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.19 WRITE FUNCTION REGISTER OPERATION (WRFR, 42h)
Information Row Lock bits (IRL3~IRL0) can be set to “1” individually by WRFR instruction in order to lock
Information Row. Since IRL bits are OTP, once it is set to “1”, it cannot set back to “0” again.
Figure 8.32 Write Function Register Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
7
9
6
10
11
12
13
14
15
Mode 3
Mode 0
SCK
Data In
SI
Instruction = 42h
2
1
0
3
5
4
High Impedence
SO
Figure 8.33 Write Function Register QPI Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
IO[3:0]
42h
7:4 3:0
Data In
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
53
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.20 ENTER QUAD PERIPHERAL INTERFACE (QPI) MODE OPERATION (QPIEN, 35h; QPIDI, F5h)
The Enter Quad Peripheral Interface (QPIEN) instruction, 35h, enables the Flash device for QPI bus operation.
Upon completion of the instruction, all instructions thereafter will be 4-bit multiplexed input/output until a power
cycle or an Exit Quad Peripheral Interface instruction is sent to device.
The Exit Quad Peripheral Interface (QPIDI) instruction, F5h, resets the device to 1-bit SPI protocol operation. To
execute an Exit Quad Peripheral Interface operation, the host drives CE# low, sends the QPIDI instruction, then
drives CE# high. The device just accepts QPI (2 clocks) command cycles.
Figure 8.34 Enter Quad Peripheral Interface (QPI) Mode Sequence
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction = 35h
SI
High Impedance
SO
Figure 8.35 Exit Quad Peripheral Interface (QPI) Mode Sequence
CE#
0
1
Mode 3
Mode 0
SCK
F5h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
54
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.21 PROGRAM/ERASE SUSPEND & RESUME
The device allows the interruption of Sector Erase, Block Erase, or Page Program operations to conduct other
operations. 75h/B0h command for suspend and 7Ah/30h for resume will be used. (SPI/QPI all acceptable) Function
Register bit2 (PSUS) and bit3 (ESUS) are used to check whether or not the device is in suspend mode.
Suspend to read ready timing: 100µs
Resume to another suspend timing: 400µs
PROGRAM/ERASE SUSPEND DURING SECTOR-ERASE OR BLOCK-ERASE (PERSUS 75h/B0h)
The Program/Erase Suspend allows the interruption of Sector Erase and Block Erase operations. After the
Program/Erase Suspend, program, read related, resume and reset commands can be accepted. It is possible to
nest a Program/Erase Suspend operation during a Program inside a Program/Erase Suspend operation. Refer to
Table 8.4 for more detail.
To execute the Program/Erase Suspend operation, the host drives CE# low, sends the Program/Erase Suspend
command cycle (75h/B0h), then drives CE# high. The Function Register indicates that the erase has been
suspended by changing the ESUS bit from “0” to “1”, but the device will not accept another command until it is
ready. To determine when the device will accept a new command, poll the WIP bit in the Status Register or wait
the specified time tSUS. When ESUS bit is issued, the Write Enable Latch (WEL) bit will be reset.
PROGRAM/ERASE SUSPEND DURING PAGE PROGRAMMING (PERSUS 75h/B0h)
The Program/Erase Suspend allows the interruption of all array program operations. After the Program/Erase
Suspend command, WEL bit will be disabled, therefore only read related, resume and reset command can be
accepted. Refer to Table 8.4 for more detail.
To execute the Program/Erase Suspend operation, the host drives CE# low, sends the Program/Erase Suspend
command cycle (75h/B0h), then drives CE# high. The Function Register indicates that the programming has been
suspended by changing the PSUS bit from “0” to “1”, but the device will not accept another command until it is
ready. To determine when the device will accept a new command, poll the WIP bit in the Status Register or wait
the specified time tSUS
.
PROGRAM/ERASE RESUME (PERRSM 7Ah/30h)
The Program/Erase Resume restarts the Program or Erase command that was suspended, and changes the
suspend status bit in the Function Register (ESUS or PSUS bits) back to “0”. To execute the Program/Erase
Resume operation, the host drives CE# low, sends the Program/Erase Resume command cycle (7Ah/30h), then
drives CE# high. A cycle is two nibbles long, most significant nibble first. To determine if the internal, self-timed
Write operation completed, poll the WIP bit in the Status Register, or wait the specified time tSE, tBE or tPP for Sector
Erase, Block Erase, or Page Programming, respectively. The total write time before suspend and after resume will
not exceed the uninterrupted write times tSE, tBE or tPP.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
55
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Table 8.4 Instructions accepted during Suspend
Operation
Instruction Allowed
Suspended
Name
Hex Code
Operation
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Erase
NORD
03h
Read Data Bytes from Memory at Normal Read Mode
Read Data Bytes from Memory at Fast Read Mode
Fast Read Dual I/O
FRD
0Bh
FRDIO
FRDO
BBh
3Bh
Fast Read Dual Output
FRQIO
FRQO
EBh
6Bh
Fast Read Quad I/O
Fast Read Quad Output
FRDTR
FRDDTR
FRQDTR
PP
0Dh
Fast Read DTR Mode
BDh
EDh
02h
Fast Read Dual I/O DTR
Fast Read Quad I/O DTR
Serial Input Page Program
Quad Input Page Program
Write Enable
Erase
PPQ
32h/38h
06h
Erase
WREN
RDSR
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Erase
05h
Read Status Register
RDFR
48h
Read Function Register
CLERP
PERRSM
PERSUS
RDID
82h
Clear Extended Read Register
Resume program/erase
7Ah/30h
75h/B0h
ABh
C0/63h
83h
Program/Erase Suspend
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Program or Erase
Erase
Read Manufacturer and Product ID
Set Read Parameters (Volatile)
Set Extended Read Parameters (Volatile)
Read Read Parameters (Volatile)
Read Extended Read Parameters (Volatile)
Read Manufacturer and Product ID by JEDEC ID Command
Read Manufacturer and Device ID
Read JEDEC ID QPI mode
Read Unique ID Number
SRPV
SERPV
RDRP
61h
RDERP
RDJDID
RDMDID
RDJDIDQ
RDUID
RDSFDP
NOP
81h
9Fh
90h
AFh
4Bh
5Ah
SFDP Read
00h
No Operation
RSTEN
RST
66h
Software reset enable
99h
Reset (Only along with 66h)
Read Information Row
IRRD
68h
SECUNLOCK
SECLOCK
RDABR
26h
Sector Unlock
Erase
24h
Sector Lock
Program or Erase
14h
Read AutoBoot Register
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
56
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.22 ENTER DEEP POWER DOWN (DP, B9h)
The Deep Power-down (DP) instruction is for setting the device on the minimizing the power consumption (enter
into Power-down mode). During this mode, standby current is reduced from Isb1 to Isb2. While in the Power-down
mode, the device is not active and all Write/Program/Erase instructions are ignored. The instruction is initiated by
driving the CE# pin low and shifting the instruction code into the device. The CE# pin must be driven high after the
instruction has been latched, or Power-down mode will not engage. Once CE# pin driven high, the Power-down
mode will be entered within the time duration of tDP. While in the Power-down mode only the Release from Power-
down/RDID instruction, which restores the device to normal operation, will be recognized. All other instructions are
ignored, including the Read Status Register instruction which is always available during normal operation. Ignoring
all but one instruction makes the Power Down state a useful condition for securing maximum write protection. It is
available in both SPI and QPI mode.
Figure 8.36 Enter Deep Power Down Mode Sequence In SPI MOde
CE#
SCK
tDP
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SI
Instruction = B9h
High Impedance
SO
Figure 8.37 Enter Deep Power Down Mode Sequence In QPI Mode
tDP
CE#
0
1
Mode 3
Mode 0
SCK
B9h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
57
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.23 RELEASE DEEP POWER DOWN (RDPD, ABh)
The Release Deep Power-down/Read Device ID instruction is a multi-purpose command. To release the device
from the Power-down mode, the instruction is issued by driving the CE# pin low, shifting the instruction code “ABh”
and driving CE# high.
Releasing the device from Power-down mode will take the time duration of tRES1 before normal operation is restored
and other instructions are accepted. The CE# pin must remain high during the tRES1 time duration. If the Release
Deep Power-down/RDID instruction is issued while an Erase, Program or Write cycle is in progress (WIP=1) the
instruction is ignored and will not have any effects on the current cycle.
Figure 8.38 Release Deep Power Down Mode Sequence In SPI Mode
CE#
SCK
tRES1
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SI
Instruction = ABh
High Impedance
SO
Figure 8.39 Release Deep Power Down Mode Sequence In QPI Mode
tRES1
CE#
0
1
Mode 3
Mode 0
SCK
ABh
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
58
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.24 SET READ PARAMETERS OPERATION (SRPNV: 65h, SRPV: C0h/63h)
Set Read Parameter Bits
This device supports configurable burst length and dummy cycles in both SPI and QPI mode by setting three bits
(P2, P1, P0) and four bits (P6, P5, P4, P3) within the Read Register, respectively. To set those bits the SRPNV
and SRPV operation instruction are used. Details regarding burst length and dummy cycles can be found in Table
6.9, Table 6.10, and Table 6.11. HOLD#/RESET# pin selection (P7) bit in the Read Register can be set with the
SRPNV and SRPV operation as well, in order to select RESET# pin instead of HOLD# pin.
SRPNV is used to set the non-volatile Read register, while SRPV is used to set the volatile Read register.
Note: When SRPNV is executed, the volatile Read Register is set as well as the non-volatile Read Register.
Figure 8.40 Set Read Parameters Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
7
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
Data In
SI
Instruction = 65h or C0h/63h
High Impedence
2
1
0
3
6
5
4
SO
Figure 8.41 Set Read Parameters Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
65h or
C0h/63h
IO[3:0]
7:4 3:0
Data In
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
59
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Read with “8/16/32/64-Byte Wrap Around”
The device is capable of burst read with wrap around in both SPI and QPI mode. The size of burst length is
configurable by using P0, P1, and P2 bits in Read Register. P2 bit (Wrap enable) enables the burst mode feature.
P0 and P1 define the size of burst. Burst lengths of 8, 16, 32, and 64 bytes are supported. By default, address
increases by one up through the entire array. By setting the burst length, the data being accessed can be limited
to the length of burst boundary within a 256 byte page. The first output will be the data at the initial address which
is specified in the instruction. Following data will come out from the next address within the burst boundary. Once
the address reaches the end of boundary, it will automatically move to the first address of the boundary. CE# high
will terminate the command.
For example, if burst length of 8 and initial address being applied is 0h, following byte output will be from address
00h and continue to 01h,..,07h, 00h, 01h… until CE# terminates the operation. If burst length of 8 and initial address
being applied is FEh(254d), following byte output will be from address FEh and continue to FFh, F8h, F9h, FAh,
FBh, FCh, FDh, and repeat from FEh until CE# terminates the operation.
The commands, “SRPV (65h) or SRPNV (C0h or 63h)”, are used to configure the burst length. If the following data
input is one of “00h”,”01h”,”02h”, and ”03h”, the device will be in default operation mode. It will be continuous burst
read of the whole array. If the following data input is one of “04h”,”05h”,”06h”, and ”07h”, the device will set the
burst length as 8,16,32 and 64, respectively.
To exit the burst mode, another “C0h or 63h” command is necessary to set P2 to 0. Otherwise, the burst mode will
be retained until either power down or reset operation. To change burst length, another “C0h or 63h” command
should be executed to set P0 and P1 (Detailed information in Table 6.9 Burst Length Data). All read commands
will operate in burst mode once the Read Register is set to enable burst mode.
Refer to Figure 8.40 and Figure 8.41 for instruction sequence.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
60
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.25 SET EXTENDED READ PARAMETERS OPERATION (SERPNV: 85h, SERPV: 83h)
Set Read Operational Driver Strength
This device supports configurable Operational Driver Strength in both SPI and QPI modes by setting three bits
(ODS0, ODS1, ODS2) within the Extended Read Register. To set the ODS bits the SERPNV and SERPV operation
instructions are required. The device’s driver strength can be reduced as low as 12.50% of full drive strength.
Details regarding the driver strength can be found in Table 6.14.
SERPNV is used to set the non-volatile Extended Read register, while SERPV is used to set the volatile Extended
Read register.
Notes:
1. The default driver strength is set to 50%.
2. When SERPNV is executed, the volatile Read Extended Register is set as well as the non-volatile Read Extended
Register.
Figure 8.42 Set Extended Read Parameters Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
7
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
Data In
SI
Instruction = 85h/83h
High Impedence
2
1
0
3
6
5
4
SO
Figure 8.43 Set Extended Read Parameters Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
IO[3:0]
85h/83h
7:4 3:0
Data In
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
61
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.26 READ READ PARAMETERS OPERATION (RDRP, 61h)
Prior to, or after setting Read Register, the data of the Read Register can be confirmed by the RDRP command.
The instruction is only applicable for the volatile Read Register, not for the non-volatile Read Register.
Figure 8.44 Read Read Parameters Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
SI
Instruction = 61h
tV
Data Out
SO
3
2
1
0
7
6
5
4
Figure 8.45 Read Read Parameters Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
tV
IO[3:0]
61h
7:4 3:0
Data Out
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
62
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.27 READ EXTENDED READ PARAMETERS OPERATION (RDERP, 81h)
Prior to, or after setting Extended Read Register, the data of the Extended Read Register can be confirmed by the
RDERP command. The instruction is only applicable for the volatile Extended Read Register, not for the non-
volatile Extended Read Register.
During the execution of a Program, Erase or Write Non-Volatile Register operation, the RDERP instruction will be
executed, which can be used to check the progress or completion of an operation by reading the WIP bit.
Figure 8.46 Read Extended Read Parameters Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
SI
Instruction = 81h
tV
Data Out
SO
3
2
1
0
7
6
5
4
Figure 8.47 Read Extended Read Parameters Sequence In QPI Mode
CE#
0
1
2
3
Mode 3
Mode 0
SCK
tV
IO[3:0]
81h
7:4 3:0
Data Out
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
63
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.28 CLEAR EXTENDED READ PARAMETERS OPERATION (CLERP, 82h)
A Clear Extended Read Register (CLERP) instruction clears PROT_E, P_ERR, and E_ERR error bits in the
Extended Read Register to “0” when the error bits are set to “1”. Once the error bits are set to “1”, they remains set
to “1” until they are cleared to “0” with a CLERP command.
Figure 8.48 Clear Extended Read Parameters Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction = 82h
SI
High Impedance
SO
Figure 8.49 Clear Extended Read Parameters Sequence In QPI Mode
CE#
0
1
Mode 3
Mode 0
SCK
82h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
64
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.29 READ PRODUCT IDENTIFICATION (RDID, ABh)
The Release from Power-down/Read Device ID instruction is a multi-purpose instruction. It can support both SPI
and QPI modes. The Read Product Identification (RDID) instruction is for reading out the old style of 8-bit Electronic
Signature, whose values are shown as table of Product Identification.
The RDID instruction code is followed by three dummy bytes, each bit being latched-in on SI during the rising SCK
edge. Then the Device ID is shifted out on SO with the MSB first, each bit been shifted out during the falling edge
of SCK. The RDID instruction is ended by driving CE# high. The Device ID (ID7-ID0) outputs repeatedly if additional
clock cycles are continuously sent to SCK while CE# is at low.
Table 8.5 Product Identification
Manufacturer ID
ISSI Serial Flash
Instruction
(MF7-MF0)
9Dh
ABh
90h
9Fh
Memory Type + Capacity
(ID15-ID0)
Part Number
IS25LP080D
IS25WP080D
IS25WP040D
IS25WP020D
Device ID (ID7-ID0)
13h
13h
12h
11h
6014h
7014h
7013h
7012h
Figure 8.50 RDID (Read Product Identification) Sequence In SPI Mode
CE#
0
1
...
7
8
9
...
31
32
33
...
39
Mode 3
Mode 0
SCK
SI
Instruction = ABh
3 Dummy Bytes
Data Out
tV
Device ID
(ID7-ID0)
SO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
65
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.51 RDID (Read Product Identification) Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
Mode 3
Mode 0
SCK
tV
Device ID
(ID7-ID0)
ABh
6 Dummy Cycles
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
66
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.30 READ PRODUCT IDENTIFICATION BY JEDEC ID OPERATION (RDJDID, 9Fh; RDJDIDQ, AFh)
The JEDEC ID READ instruction allows the user to read the manufacturer and product ID of devices. Refer to Table
8.5 Product Identification for Manufacturer ID and Device ID. After the JEDEC ID READ command (9Fh in SPI
mode, AFh in QPI mode) is input, the Manufacturer ID is shifted out MSB first followed by the 2-byte electronic ID
(ID15-ID0) that indicates Memory Type and Capacity, one bit at a time. Each bit is shifted out during the falling
edge of SCK. If CE# stays low after the last bit of the 2-byte electronic ID, the Manufacturer ID and 2-byte electronic
ID will loop until CE# is pulled high.
Figure 8.52 RDJDID (Read JEDEC ID In SPI Mode) Sequence
CE#
0
1
...
7
8
9
...
15
16
17
...
23
24
25
...
31
Mode 3
Mode 0
SCK
SI
Instruction = 9Fh
tV
Manufacturer ID
(MF7-MF0)
Capacity
(ID7-ID0)
Memory Type
(ID15-ID8)
SO
Figure 8.53 RDJDIDQ (Read JEDEC ID In QPI Mode) Sequence
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
tV
AFh
IO[3:0]
7:4 3:0
MF7-MF0
7:4 3:0
ID15-ID8
7:4 3:0
ID7-ID0
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
67
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.31 READ DEVICE MANUFACTURER AND DEVICE ID OPERATION (RDMDID, 90h)
The Read Device Manufacturer and Device ID (RDMDID) instruction allows the user to read the Manufacturer and
product ID of devices. Refer to Table 8.5 Product Identification for Manufacturer ID and Device ID. The RDMDID
instruction code is followed by two dummy bytes and one byte address (A7~A0), each bit being latched-in on SI
during the rising edge of SCK. If one byte address is initially set as A0 = 0, then the Manufacturer ID is shifted out
on SO with the MSB first followed by the Device ID (ID7- ID0). Each bit is shifted out during the falling edge of SCK.
If one byte address is initially set as A0 = 1, then Device ID will be read first followed by the Manufacturer ID. The
Manufacturer and Device ID can be read continuously alternating between the two until CE# is driven high.
Figure 8.54 RDMDID (Read Product Identification) Sequence In SPI Mode
CE#
0
1
...
7
8
9
...
31
32
33
...
39
40
41
...
47
Mode 3
Mode 0
SCK
SI
Instruction = 90h
3-byte Address
tV
Device ID
(ID7-ID0)
Manufacturer ID
(MF7-MF0)
SO
Notes:
1. ADDRESS A0 = 0, will output the 1-byte Manufacturer ID (MF7-MF0) 1-byte Device ID (ID7-ID0)
ADDRESS A0 = 1, will output the 1-byte Device ID (ID7-ID0) 1-byte Manufacturer ID (MF7-MF0)
2. The Manufacturer and Device ID can be read continuously and will alternate from one to the other until CE# pin is
pulled high.
Figure 8.55 RDMDID (Read Product Identification) Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
Mode 3
Mode 0
SCK
tV
IO[3:0]
90h
Instruction
23:20 19:16 15:12 11:8 7:4 3:0
3-byte Address
7:4 3:0
7:4 3:0
Manufacturer
ID (MF7-MF0)
Device ID
(ID7-ID0)
Notes:
1. ADDRESS A0 = 0, will output the 1-byte Manufacturer ID (MF7-MF0) 1-byte Device ID (ID7-ID0)
ADDRESS A0 = 1, will output the 1-byte Device ID (ID7-ID0) 1-byte Manufacturer ID (MF7-MF0)
2. The Manufacturer and Device ID can be read continuously and will alternate from one to the other until CE# pin is
pulled high.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
68
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.31 READ UNIQUE ID NUMBER (RDUID, 4Bh)
The Read Unique ID Number (RDUID) instruction accesses a factory-set read-only 16-byte number that is unique
to the device. The ID number can be used in conjunction with user software methods to help prevent copying or
cloning of a system. The RDUID instruction is instated by driving the CE# pin low and shifting the instruction code
(4Bh) followed by 3 address bytes and dummy cycles (configurable, default is 8 clocks). After which, the 16-byte
ID is shifted out on the falling edge of SCK as shown below. As a result, the sequence of RDUID instruction is same
as FAST READ. RDUID QPI sequence is also same as FAST READ QPI except for the instruction code. Refer to
the FAST READ QPI operation.
Note: 16 bytes of data will repeat as long as CE# is low and SCK is toggling.
Figure 8.56 RDUID Sequence
CE#
0
1
...
7
8
9
...
31
32
33
...
39
40
41
...
47
...
Mode 3
Mode 0
SCK
SI
Instruction = 4Bh
3 Byte Address
Dummy Cycles
tV
SO
Data Out
Note: Dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy Cycles.
Table 8.6 Unique ID Addressing
A[23:16]
A[15:9]
A[8:4]
A[3:0]
XXh
XXh
00h
0h Byte address
1h Byte address
2h Byte address
XXh
XXh
00h
XXh
XXh
00h
XXh
XXh
00h
XXh
XXh
00h
Fh Byte address
Note: XX means “don’t care”.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
69
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.32 READ SFDP OPERATION (RDSFDP, 5Ah)
The Serial Flash Discoverable Parameters (SFDP) standard provides a consistent method of describing the
functions and features of serial Flash devices in a standard set of internal parameter tables. These parameters can
be interrogated by host system software to enable adjustments needed to accommodate divergent features from
multiple vendors. For more details please refer to the JEDEC Standard JESD216 (Serial Flash Discoverable
Parameters).
The sequence of issuing RDSFDP instruction in SPI mode is:
CE# goes low Send RDSFDP instruction (5Ah) Send 3 address bytes on SI pin 8 dummy cycles on SI pin
Read SFDP code on SO End RDSFDP operation by driving CE# high at any time during data out. Refer to
ISSI’s Application note for SFDP table. The data at the addresses that are not specified in SFDP table are
undefined.
RDSFDP Sequence in QPI mode, has 8 dummy cycles before SFDP code, too.
Figure 8.57 RDSFDP (Read SFDP) Sequence in SPI mode
CE#
0
1
...
7
8
9
...
31
32
33
...
39
40
41
...
47
...
Mode 3
Mode 0
SCK
SI
Instruction = 5Ah
3 Byte Address
Dummy Cycles
tV
SO
Data Out
8.33 NO OPERATION (NOP, 00h)
The No Operation command solely cancels a Reset Enable command and has no impact on any other commands.
It is available in both SPI and QPI modes. To execute a NOP, the host drives CE# low, sends the NOP command
cycle (00H), then drives CE# high.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
70
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.34 SOFTWARE RESET (RESET-ENABLE (RSTEN, 66h) AND RESET (RST, 99h)) AND HARDWARE RESET
The Software Reset operation is used as a system reset that puts the device in normal operating mode. During the
Reset operation, the value of volatile registers will default back to the value in the corresponding non-volatile
register. This operation consists of two commands: Reset-Enable (RSTEN) and Reset (RST). The operation
requires the Reset-Enable command followed by the Reset command. Any command other than the Reset
command after the Reset-Enable command will disable the Reset-Enable.
Execute the CE# pin low sends the Reset-Enable command (66h), and drives CE# high. Next, the host drives
CE# low again, sends the Reset command (99h), and pulls CE# high.
Only if the RESET# pin is enabled, Hardware Reset function is available.
For all other packages except the package with dedicated RESET# pin (or ball) option, the RESET# pin (or ball)
will be solely applicable in SPI mode and when the QE bit is disabled.
For the package with dedicated RESET# pin (or ball), the RESET# pin (or ball) is always applicable regardless of
the QE bit value in Status Register and HOLD#/RESET# selection bit (P7) in Read Register. The dedicated
RESET# pin has an internal pull-up resistor and may be left floating if not used. The RESET# pin (or ball) has the
highest priority among all the input signals and will reset the device to its initial power-on state regardless of the
state of all other pins (CE#, IOs, SCK, and WP#).
In order to activate Hardware Reset, the RESET# pin (or ball) must be driven low for a minimum period of tRESET
(1µs). Drive RESET# low for a minimum period of tRESET will interrupt any on-going internal and external operations,
release the device from deep power down mode1, disable all input signals, force the output pin enter a state of high
impedance, and reset all the read parameters. If the RESET# pulse is driven for a period shorter than 1µs, it may
still reset the device, however the 1µs minimum period is recommended to ensure the reliable operation. The
required wait time after activating a HW Reset before the device will accept another instruction (tHWRST) is the same
as the maximum value of tSUS (100µs).
The Software/Hardware Reset during an active Program or Erase operation aborts the operation, which can result
in corrupting or losing the data of the targeted address range. Depending on the prior operation, the reset timing
may vary. Recovery from a Write operation will require more latency than recovery from other operations.
Note1: The Status and Function Registers remain unaffected.
Figure 8.58 Software Reset Enable and Software Reset Sequence In SPI Mode (RSTEN, 66h + RST, 99h)
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
Instruction = 66h
High Impedance
Instruction = 99h
SI
SO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
71
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.59 Software Reset Enable and Software Reset Sequence In QPI Mode (RSTEN, 66h + RST, 99h)
CE#
0
1
0
1
Mode 3
Mode 0
SCK
66h
99h
IO[3:0]
8.35 SECURITY INFORMATION ROW
The security Information Row is comprised of an additional 4 x 256 bytes of programmable information. The security
bits can be reprogrammed by the user. Any program security instruction issued while an erase, program or write
cycle is in progress is rejected without having any effect on the cycle that is in progress.
Table 8.7 Information Row Valid Address Range
Address Assignment
A[23:16]
00h
A[15:8]
00h
A[7:0]
IRL0 (Information Row Lock0)
Byte address
Byte address
Byte address
Byte address
IRL1
IRL2
IRL3
00h
10h
00h
20h
00h
30h
Bit 7~4 of the Function Register is used to permanently lock the programmable memory array.
When Function Register bit IRLx = “0”, the 256 bytes of the programmable memory array can be programmed.
When Function Register bit IRLx = “1”, the 256 bytes of the programmable memory array function as read only.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
72
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.36 INFORMATION ROW ERASE OPERATION (IRER, 64h)
Information Row Erase (IRER) instruction erases the data in the Information Row x (x: 0~3) array. Prior to the
operation, the Write Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL bit is
automatically reset after the completion of the operation.
The sequence of IRER operation: Pull CE# low to select the device Send IRER instruction code Send three
address bytes Pull CE# high. CE# should remain low during the entire instruction sequence. Once CE# is pulled
high, Erase operation will begin immediately. The internal control logic automatically handles the erase voltage and
timing.
Figure 8.60 IRER (Information Row Erase) Sequence
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
...
SI
3
Instruction = 64h
2
1
0
23
22
High Impedance
SO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
73
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.37 INFORMATION ROW PROGRAM OPERATION (IRP, 62h)
The Information Row Program (IRP) instruction allows up to 256 bytes data to be programmed into the memory in
a single operation. Before the execution of IRP instruction, the Write Enable Latch (WEL) must be enabled through
a Write Enable (WREN) instruction.
The IRP instruction code, three address bytes and program data (1 to 256 bytes) should be sequentially input.
Three address bytes has to be input as specified in the Table 8.7 Information Row Valid Address Range. Program
operation will start once the CE# goes high, otherwise the IRP instruction will not be executed. The internal control
logic automatically handles the programming voltages and timing. During a program operation, all instructions will
be ignored except the RDSR instruction. The progress or completion of the program operation can be determined
by reading the WIP bit in Status Register via a RDSR instruction. If the WIP bit is “1”, the program operation is still
in progress. If WIP bit is “0”, the program operation has completed.
If more than 256 bytes data are sent to a device, the address counter rolls over within the same page. The
previously latched data are discarded and the last 256 bytes data are kept to be programmed into the page. The
starting byte can be anywhere within the page. When the end of the page is reached, the address will wrap around
to the beginning of the same page. If the data to be programmed are less than a full page, the data of all other
bytes on the same page will remain unchanged.
Note: A program operation can alter “1”s into “0”s, The same byte location or Information Row array may be
programmed more than once to incrementally change “1” to “0”s. An erase operation is required to change “0”s
back to “1”s.
Figure 8.61 IRP (Information Row Program) Sequence
CE#
0
1
...
7
8
9
...
31
32
33
...
39
...
...
...
Mode 3
Mode 0
SCK
3-byte Address
Data In 1
Data In 256
...
SI
...
...
6
0
7
0
0
Instruction = 62h
7
23
22
High Impedance
SO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
74
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.38 INFORMATION ROW READ OPERATION (IRRD, 68h)
The IRRD instruction is used to read memory data at up to a 133MHz clock.
The IRRD instruction code is followed by three address bytes (A23 - A0) and dummy cycles (configurable, default
is 8 clocks), transmitted via the SI line, with each bit latched-in during the rising edge of SCK. Then the first data
byte addressed is shifted out on the SO line, with each bit shifted out at a maximum frequency fCT, during the falling
edge of SCK.
The address is automatically incremented by one after each byte of data is shifted out. Once the address reaches
the last address of each 256 byte Information Row, the next address will not be valid and the data of the address
will be garbage data. It is recommended to repeat four times IRRD operation that reads 256 byte with a valid starting
address of each Information Row in order to read all data in the 4 x 256 byte Information Row array. The IRRD
instruction is terminated by driving CE# high (VIH).
If an IRRD instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is
ignored and will not have any effects on the current cycle.
The sequence of IRRD instruction is same as FAST READ except for the instruction code. IRRD QPI sequence is
also same as FAST READ QPI except for the instruction code. Refer to the FAST READ QPI operation.
Figure 8.62 IRRD (Information Row Read) Sequence
CE#
0
1
...
7
8
9
...
31
32
33
...
39
40
41
...
47
...
Mode 3
Mode 0
SCK
SI
Instruction = 68h
3 Byte Address
Dummy Cycles
tV
SO
Data Out
Note: Dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
75
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.39 FAST READ DTR MODE OPERATION IN SPI MODE (FRDTR, 0Dh)
The FRDTR instruction is for doubling the data in and out. Signals are triggered on both rising and falling edge of
clock. The address is latched on both rising and falling edge of SCK, and data of each bit shifts out on both rising
and falling edge of SCK at a maximum frequency fC2. The 2-bit address can be latched-in at one clock, and 2-bit
data can be read out at one clock, which means one bit at the rising edge of clock, the other bit at the falling edge
of clock.
The first address byte can be at any location. The address is automatically increased to the next higher address
after each byte of data is shifted out, so the whole memory can be read out in a single FRDTR instruction. The
address counter rolls over to 0 when the highest address is reached.
The sequence of issuing FRDTR instruction is: CE# goes low Sending FRDTR instruction code (1bit per clock)
3-byte address on SI (2-bit per clock) 8 dummy clocks (configurable, default is 8 clocks) on SI Data out on
SO (2-bit per clock) End FRDTR operation via driving CE# high at any time during data out.
While a Program/Erase/Write Status Register cycle is in progress, FRDTR instruction will be rejected without any
effect on the current cycle.
Figure 8.63 FRDTR Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
...
19
20
21
Mode 3
Mode 0
SCK
3-byte Address
SI
...
Instruction = 0Dh
23 22 21
19
0
20
18
17
High Impedance
SO
CE#
SCK
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
...
tV
8 Dummy Cycles
SI
Data Out 1
Data Out 2
Data Out ...
...
6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5
SO
7
Note: Dummy cycles depends on Read Parameter setting. Detailed information in Table 6.11 Read Dummy Cycles.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
76
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
FAST READ DTR MODE OPERATION IN QPI MODE (FRDTR, 0Dh)
The FRDTR QPI instruction utilizes all four IO lines to input the instruction code so that only two clocks are required,
while the FRDTR instruction requires that the byte-long instruction code is shifted into the device only via IO0 line
in eight clocks. In addition, subsequent address and data out are shifted in/out via all four IO lines unlike the FRDTR
instruction. Eventually this operation is same as the FRQDTR QPI, but the only different thing is that AX mode is
not available in the FRDTR QPI operation.
The sequence of issuing FRDTR QPI instruction is: CE# goes low Sending FRDTR QPI instruction (4-bit per
clock) 24-bit address interleave on IO3, IO2, IO1 & IO0 (8-bit per clock) 6 dummy clocks (configurable, default
is 6 clocks) Data out interleave on IO3, IO2, IO1 & IO0 (8-bit per clock) End FRDTR QPI operation by driving
CE# high at any time during data out.
If the FRDTR QPI instruction is issued while a Program/Erase/Write Status Register cycle is in progress (WIP=1),
the instruction will be rejected without any effect on the current cycle.
Figure 8.64 FRDTR Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
...
Mode 3
Mode 0
SCK
IO0
6 Dummy Cycles
Data Data
Out Out
Instruction
= 0Dh
tV
3-byte Address
...
...
...
...
4
5
6
7
0
1
2
3
20 16 12 8
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO1
IO2
21 17 13 9
5
22 18 14 10 6
23 19 15 11 7
IO3
Notes:
1. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
2. Sufficient dummy cycles are required to avoid I/O contention.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
77
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.40 FAST READ DUAL IO DTR MODE OPERATION (FRDDTR, BDh)
The FRDDTR instruction enables Double Transfer Rate throughput on dual I/O of the device in read mode. The
address (interleave on dual I/O pins) is latched on both rising and falling edge of SCK, and the data (interleave on
dual I/O pins) shift out on both rising and falling edge of SCK at a maximum frequency fT2. The 4-bit address can
be latched-in at one clock, and 4-bit data can be read out at one clock, which means two bits at the rising edge of
clock, the other two bits at the falling edge of clock.
The first address byte can be at any location. The address is automatically increased to the next higher address
after each byte of data is shifted out, so the whole memory can be read out with a single FRDDTR instruction. The
address counter rolls over to 0 when the highest address is reached. Once writing FRDDTR instruction, the
following address/dummy/data out will perform as 4-bit instead of previous 1-bit.
The sequence of issuing FRDDTR instruction is: CE# goes low Sending FRDDTR instruction (1-bit per clock)
24-bit address interleave on IO1 & IO0 (4-bit per clock) 4 dummy clocks (configurable, default is 4 clocks) on
IO1 & IO0 Data out interleave on IO1 & IO0 (4-bit per clock) End FRDDTR operation via pulling CE# high at
any time during data out (Please refer to Figure 8.64 for 2 x I/O Double Transfer Rate Read Mode Timing Waveform).
If AXh (where X is don’t care) is input for the mode bits during dummy cycles, the device will enter AX read operation
mode which enables subsequent FRDDTR execution skips command code. It saves cycles as described in Figure
8.65. When the code is different from AXh, the device exits the AX read operation. After finishing the read operation,
device becomes ready to receive a new command.
If the FRDDTR instruction is issued while a Program/Erase/Write Status Register cycle is in progress (WIP=1), the
instruction will be rejected without any effect on the current cycle.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
78
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.65 FRDDTR Sequence (with command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
...
13
14
Mode 3
Mode 0
SCK
3-byte Address
4 Dummy Cycles
IO0
IO1
...
Instruction = BDh
22 20 18 16 14 12 10
0 6
4
Mode Bits
High Impedance
...
23 21 19 17 15 13 11
1 7
5
CE#
SCK
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
...
tV
Data Out Data Out
Data Out Data Out
Data Out
Data Out
IO0
IO1
...
...
2
0
6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0
Mode Bits
3
1
7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1
Notes:
1. If the mode bits=AXh (where X is don’t care), it can execute the AX read mode (without command). When the mode
bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
79
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.66 FRDDTR AX Read Sequence (without command decode cycles)
CE#
...
0
1
2
6
7
8
9
10
11
12
13
14
15
16
...
Mode 3
Mode 0
SCK
4 Dummy Cycles
tV
Data Out Data Out
Data Out
3-byte Address
IO0
...
...
...
...
22 20 18 16 14 12 10
0 6 4 2 0
Mode Bits
6 4 2 0 6 4 2 0 6 4 2 0
IO1
7 5 3 1 7 5 3 1 7 5 3
1
23 21 19 17 15 13 11
1 7 5 3 1
Notes:
1. If the mode bits=AXh (where X is don’t care), it will keep executing the AX read mode (without command). When the
mode bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
80
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.41 FAST READ QUAD IO DTR MODE OPERATION IN SPI MODE (FRQDTR, EDh)
The FRQDTR instruction enables Double Transfer Rate throughput on quad I/O of the device in read mode. A
Quad Enable (QE) bit of Status Register must be set to "1" before sending the FRQDTR instruction. The address
(interleave on 4 I/O pins) is latched on both rising and falling edge of SCK, and data (interleave on 4 I/O pins) shift
out on both rising and falling edge of SCK at a maximum frequency fQ2. The 8-bit address can be latched-in at one
clock, and 8-bit data can be read out at one clock, which means four bits at the rising edge of clock, the other four
bits at the falling edge of clock.
The first address byte can be at any location. The address is automatically increased to the next higher address
after each byte data is shifted out, so the whole memory can be read out with a single FRQDTR instruction. The
address counter rolls over to 0 when the highest address is reached. Once writing FRQDTR instruction, the
following address/dummy/data out will perform as 8-bit instead of previous 1-bit.
The sequence of issuing FRQDTR instruction is: CE# goes low Sending FRQDTR instruction (1-bit per clock)
24-bit address interleave on IO3, IO2, IO1 & IO0 (8-bit per clock) 6 dummy clocks (configurable, default is 6
clocks) Data out interleave on IO3, IO2, IO1 & IO0 (8-bit per clock) End FRQDTR operation by driving CE#
high at any time during data out.
If AXh (where X is don’t care) is input for the mode bits during dummy cycles, the device will enter AX read operation
mode which enables subsequent FRQDTR execution skips command code. It saves cycles as described in Figure
8.68. When the code is different from AXh, the device exits the AX read operation. After finishing the read operation,
device becomes ready to receive a new command.
If the FRQDTR instruction is issued while a Program/Erase/Write Status Register cycle is in progress (WIP=1), the
instruction will be rejected without any effect on the current cycle.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
81
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.67 FRQDTR Sequence (with command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
Mode 3
Mode 0
SCK
IO0
6 Dummy Cycles
3-byte Address
Instruction = EDh
High Impedance
20 16 12 8
4
0
4
0
1
IO1
IO2
21 17 13 9
5
1
2
3
5
6
7
22 18 14 10 6
23 19 15 11 7
2
3
IO3
Mode Bits
CE#
SCK
13
14
15
16
17
18
19
20
21
22
23
24
25
26
...
Data Data Data Data Data Data Data Data Data Data
Out Out Out Out Out Out Out Out Out Out
tV
IO0
...
...
...
...
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO1
IO2
IO3
Notes:
1. If the mode bits=AXh (where X is don’t care), it can execute the AX read mode (without command). When the mode
bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
82
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.68 FRQDTR Sequence (without command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
...
Mode 3
Mode 0
SCK
IO0
Data Data Data Data
Out Out Out Out
6 Dummy Cycles
3-byte Address
tV
...
...
...
...
20 16 12 8
4
0
4
0
1
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO1
IO2
21 17 13 9
5
1
2
3
5
6
7
22 18 14 10 6
23 19 15 11 7
2
3
IO3
Mode Bits
Notes:
1. If the mode bits=AXh (where X is don’t care), it will keep executing the AX read mode (without command). When the
mode bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
83
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
FAST READ QUAD IO DTR MODE OPERATION IN QPI MODE (FRQDTR QPI, EDh)
The FRQDTR QPI instruction utilizes all four IO lines to input the instruction code so that only two clocks are
required, while the FRQDTR instruction requires that the byte-long instruction code is shifted into the device only
via IO0 line in eight clocks. As a result, 6 command cycles will be reduced by the FRQDTR QPI instruction. In
addition, subsequent address and data out are shifted in/out via all four IO lines like the FRQDTR instruction. In
fact, except for the command cycle, the FRQDTR QPI operation is exactly same as the FRQDTR.
The sequence of issuing FRQDTR QPI instruction is: CE# goes low Sending FRQDTR QPI instruction (4-bit per
clock) 24-bit address interleave on IO3, IO2, IO1 & IO0 (8-bit per clock) 6 dummy clocks (configurable, default
is 6 clocks) Data out interleave on IO3, IO2, IO1 & IO0 (8-bit per clock) End FRQDTR QPI operation by driving
CE# high at any time during data out.
If AXh (where X is don’t care) is input for the mode bits during dummy cycles, the device will enter AX read operation
mode which enables subsequent FRQDTR QPI execution skips command code. It saves cycles as described in
Figure 8.68. When the code is different from AXh, the device exits the AX read operation. After finishing the read
operation, device becomes ready to receive a new command.
If the FRQDTR QPI instruction is issued while a Program/Erase/Write Status Register cycle is in progress (WIP=1),
the instruction will be rejected without any effect on the current cycle.
Figure 8.69 FRQDTR QPI Sequence (with command decode cycles)
CE#
0
1
2
3
4
5
6
7
8
9
10
11
12
...
Mode 3
Mode 0
SCK
IO0
6 Dummy Cycles
Data Data
Out Out
Instruction
= EDh
tV
3-byte Address
...
...
...
...
4
5
6
7
0
1
2
3
20 16 12 8
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO1
IO2
21 17 13 9
5
22 18 14 10 6
23 19 15 11 7
IO3
Mode Bits
Notes:
1. If the mode bits=AXh (where X is don’t care), it can execute the AX read mode (without command). When the mode
bits are different from AXh, the device exits the AX read operation.
2. Number of dummy cycles depends on clock speed. Detailed information in Table 6.11 Read Dummy Cycles.
3. Sufficient dummy cycles are required to avoid I/O contention. If the number of dummy cycles and AX bit cycles are
same, then X should be Hi-Z.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
84
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.42 SECTOR LOCK/UNLOCK FUNCTIONS
SECTOR UNLOCK OPERATION (SECUNLOCK, 26h)
The Sector Unlock command allows the user to select a specific sector to allow program and erase operations.
This instruction is effective when the blocks are designated as write-protected through the BP0, BP1, BP2, and
BP3 bits in the Status Register. Only one sector can be enabled at any time. To enable a different sector, a
previously enabled sector must be disabled by executing a Sector Lock command. The instruction code is followed
by a 24-bit address specifying the target sector, but A0 through A11 are not decoded. The remaining sectors within
the same block remain as read-only.
Figure 8.70 Sector Unlock Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
8
9
10
21
...
28
29
30
31
Mode 3
Mode 0
SCK
3-byte Address
...
SI
Instruction = 26h
3
2
1
0
23
22
High Impedance
SO
Figure 8.71 Sector Unlock QPI Sequence In QPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction
26h
3-byte Address
23:20 19:16 15:12 11:8 7:4 3:0
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
85
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
SECTOR LOCK OPERATION (SECLOCK, 24h)
The Sector Lock command relocks a sector that was previously unlocked by the Sector Unlock command. The
instruction code does not require an address to be specified, as only one sector can be enabled at a time. The
remaining sectors within the same block remain in read-only mode.
Figure 8.72 Sector Lock Sequence In SPI Mode
CE#
0
1
2
3
4
5
6
7
Mode 3
Mode 0
SCK
Instruction = 24h
SI
High Impedance
SO
Figure 8.73 Sector Lock QPI Sequence In QPI Mode
CE#
0
1
Mode 3
SCK
Mode 0
24h
IO[3:0]
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
86
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
8.43 AUTOBOOT
SPI devices normally require 32 or more cycles of command and address shifting to initiate a read command. And,
in order to read boot code from an SPI device, the host memory controller or processor must supply the read
command from a hardwired state machine or from some host processor internal ROM code.
Parallel NOR devices need only an initial address, supplied in parallel in a single cycle, and initial access time to
start reading boot code.
The AutoBoot feature allows the host memory controller to take boot code from the device immediately after the
end of reset, without having to send a read command. This saves 32 or more cycles and simplifies the logic needed
to initiate the reading of boot code.
As part of the Power-up Reset, Hardware Reset, or Software Reset process the AutoBoot feature automatically
starts a read access from a pre-specified address. At the time the reset process is completed, the device is
ready to deliver code from the starting address. The host memory controller only needs to drive CE# signal from
high to low and begin toggling the SCK signal. The device will delay code output for a pre-specified number of
clock cycles before code streams out.
– The Auto Boot Start Delay (ABSD) field of the AutoBoot register specifies the initial delay if any is needed by
the host.
– The host cannot send commands during this time.
– If QE bit (Bit 6) in the Status Register is set to “1”, Fast Read Quad I/O operation will be selected and initial
delay is the same as dummy cycles of Fast Read Quad I/O Read operation. If it is set to “0”, Fast Read
operation will be applied and initial delay is the same as dummy cycles of Fast Read operation. Maximum
operation frequency will be 133MHz for both operations.
The starting address of the boot code is selected by the value programmed into the AutoBoot Start Address
(ABSA) field of the AutoBoot Register.
– Data will continuously shift out until CE# returns high.
At any point after the first data byte is transferred, when CE# returns high, the SPI device will reset to standard
SPI mode; able to accept normal command operations.
– A minimum of one byte must be transferred.
– AutoBoot mode will not initiate again until another power cycle or a reset occurs.
An AutoBoot Enable bit (ABE) is set to enable the AutoBoot feature.
The AutoBoot register bits are non-volatile and provide:
The starting address set by the AutoBoot Start Address (ABSA).
The number of initial delay cycles, set by the AutoBoot Start Delay (ABSD) 4-bit count value.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
87
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 8.74 AutoBoot Sequence (QE = 0)
CE#
0
1
2
...
...
n-1
n
n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8
n+9 n+10
Mode 3
Mode 0
SCK
SI
ABSD Delay (n)
High Impedance
tV
SO
...
7
6
5
4
3
2
1
0
7
6
Data Out 1
Data Out 2 ...
Figure 8.75 AutoBoot Sequence (QE = 1)
CE#
n+9 n+10
...
n-1
n
n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8
0
1
2
...
Mode 3
Mode 0
SCK
IO0
ABSD Delay (n)
tV
...
4
4
0
0
4
0
0
4
0
4
1
2
...
...
1
2
5
5
6
IO1
IO2
5
6
1
2
5
6
1
2
5
6
1
2
6
7
IO3
3
...
...
3
7
7
3
7
3
7
3
Data Out 1 Data Out 2 Data Out 3 Data Out 4 Data Out 5
High Impedance
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
88
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
AUTOBOOT REGISTER READ OPERATION (RDABR, 14h)
The AutoBoot Register Read command is shifted in. Then the 32-bit AutoBoot Register is shifted out, least
significant byte first, most significant bit of each byte first. It is possible to read the AutoBoot Register continuously
by providing multiples of 32 bits.
Figure 8.76 RDABR Sequence In SPI Mode
CE#
...
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
SCK
SI
Instruction = 14h
tV
SO
...
3
2
1
0
7
6
5
4
Data Out 1
Figure 8.77 RDABR Sequence In QPI Mode
CE#
...
0
1
2
3
Mode 3
Mode 0
SCK
tV
IO[3:0]
...
14h
7:4 3:0
Data Out
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
89
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
AUTOBOOT REGISTER WRITE OPERATION (WRABR, 15h)
Before the WRABR command can be accepted, a Write Enable (WREN) command must be issued and decoded
by the device, which sets the Write Enable Latch (WEL) in the Status Register to enable any write operations.
The WRABR command is entered by shifting the instruction and the data bytes, least significant byte first, most
significant bit of each byte first. The WRABR data is 32 bits in length.
CE# must be driven high after the 32nd bit of data has been latched. If not, the WRABR command is not executed.
As soon as CE# is driven high, the WRABR operation is initiated. While the WRABR operation is in progress, Status
Register may be read to check the value of the Write-In Progress (WIP) bit. The WIP bit is “1” during the WRABR
operation, and is a 0 when it is completed. When the WRABR cycle is completed, the WEL is set to “0”.
Figure 8.78 WRABR Sequence in SPI mode
CE#
...
0
1
2
3
4
5
6
7
8
7
9
6
10
11
12
13
14
15
Mode 3
Mode 0
SCK
SI
...
Instruction = 15h
High Impedance
3
Data In 1
2
1
0
5
4
SO
Figure 8.79 WRABR Sequence In QPI Mode
CE#
...
0
1
2
3
Mode 3
SCK
Mode 0
IO[3:0]
...
15h
7:4 3:0
Data In 1
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
90
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
9. ELECTRICAL CHARACTERISTICS
9.1 ABSOLUTE MAXIMUM RATINGS (1)
Storage Temperature
-65°C to +150°C
240°C 3 Seconds
260°C 3 Seconds
-0.5V to VCC + 0.5V
-0.5V to VCC + 0.5V
-0.5V to +6.0V
Standard Package
Lead-free Package
Surface Mount Lead Soldering Temperature
Input Voltage with Respect to Ground on All Pins
All Output Voltage with Respect to Ground
IS25LP
VCC
IS25WP
-0.5V to +2.5V
Electrostatic Discharge Voltage (Human Body Model)(2)
-2000V to +2000V
Notes:
1. Applied conditions greater than those listed in “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. ANSI/ESDA/JEDEC JS-001
9.2 OPERATING RANGE
Extended Grade E
Extended+ Grade E1
Automotive Grade A1
Automotive Grade A2
Automotive Grade A3
IS25LP
-40°C to 105°C
-40°C to 125°C
Operating Temperature
VCC Power Supply
-40°C to 85°C
-40°C to 105°C
-40°C to 125°C
2.3V (VMIN) – 3.6V (VMAX); 3.0V (Typ)
1.65V (VMIN) –1.95V (VMAX); 1.8V (Typ)
IS25WP
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
91
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
9.3 DC CHARACTERISTICS
(Under operating range)
Symbol
Parameter
Condition
NORD at 50MHz,
Min
Typ(2)
Max
6
Units
4
6
FRD Single at 133MHz
FRD Dual at 133MHz
8
8
10
13
10
11
8
FRD Quad at 133MHz
FRD Quad at 84MHz
10
8
VCC Active Read current(3)
mA
ICC1
FRD Quad at 104MHz
FRD Single DTR at 66MHz
FRD Dual DTR at 66MHz
FRD Quad DTR at 66MHz
9
6
8
10
13
25
25
25
25
25
25
25
25
25
25
25
25
10
85°C
105°C
125°C
85°C
VCC Program Current
VCC WRSR Current
CE# = VCC
CE# = VCC
CE# = VCC
CE# = VCC
CE# = VCC
CE# = VCC
CE# = VCC
22
22
22
22
8
ICC2
ICC3
ICC4
ICC5
ISB1
105°C
125°C
85°C
mA
VCC Erase Current
(SER/BER32/BER64)
105°C
125°C
85°C
VCC Erase Current (CE)
105°C
125°C
85°C
15 (4)
VCC Standby Current CMOS
105°C
125°C
85°C
20 (4)
µA
µA
30
10 (4)
15 (4)
20
IS25LP
105°C
125°C
85°C
6
Deep power down
current
ISB2
5(4)
IS25WP
105°C
125°C
1
10(4)
15
Input Leakage Current
VIN = 0V to VCC
VIN = 0V to VCC
±1
µA
µA
V
ILI
Output Leakage Current
Input Low Voltage
±1
ILO
(1)
-0.5
0.3VCC
VCC + 0.3
0.2
VIL
(1)
Input High Voltage
Output Low Voltage
Output High Voltage
0.7VCC
V
VIH
IOL = 100 µA
IOH = -100 µA
V
VOL
VOH
VCC - 0.2
V
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
92
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Notes:
1. Maximum DC voltage on input or I/O pins is VCC + 0.5V. During voltage transitions, input or I/O pins may overshoot
VCC by + 2.0V for a period of time not to exceed 20ns. Minimum DC voltage on input or I/O pins is
-0.5V. During voltage transitions, input or I/O pins may undershoot GND by -2.0V for a period of time not to exceed
20ns.
2. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC
= VCC (Typ), TA=25°C.
3. Outputs are unconnected during reading data so that output switching current is not included.
4. These parameters are characterized and are not 100% tested.
9.4 AC MEASUREMENT CONDITIONS
Symbol
Parameter
Load Capacitance up to 104MHz
Load Capacitance up to 133MHz
Input Rise and Fall Times
Min
Max
30
15
5
Units
pF
pF
ns
V
CL
TR,TF
VIN
Input Pulse Voltages
0.2VCC to 0.8VCC
VREFI
VREFO
Input Timing Reference Voltages
Output Timing Reference Voltages
0.3VCC to 0.7VCC
0.5VCC
V
V
Figure 9.1 Output test load & AC measurement I/O Waveform
0.8VCC
AC
Input
VCC/2
Measurement
1.8k
Level
0.2VCC
OUTPUT PIN
1.2k
15/30pf
9.5 PIN CAPACITANCE
(TA = 25°C, VCC=3V (IS25LPx), 1.8V (IS25WPx), 1MHz)
Symbol
Parameter
Test Condition
Min
Typ
Max
Units
Input Capacitance
(CE#, SCK)
CIN
VIN = 0V
-
-
6
pF
pF
Input/Output Capacitance
(other pins)
CIN/OUT
VIN/OUT = 0V
-
-
8
Notes:
1. These parameters are characterized and are not 100% tested.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
93
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
9.6 AC CHARACTERISTICS
(Under operating range, refer to section 9.4 for AC measurement conditions)
Symbol
Parameter
Min
Typ(3)
Max
Units
Clock Frequency for fast read mode:
SPI, Dual, Dual I/O, Quad I/O, and QPI.
Clock Frequency for fast read DTR:
SPI DTR, Dual DTR, Dual I/O DTR, Quad I/O DTR, and
QPI DTR.
fCT
0
133
MHz
fC2, fT2, fQ2
fC
0
66
50
MHz
Clock Frequency for read mode SPI
SCK Rise Time (peak to peak)
SCK Fall Time ( peak to peak)
0
MHz
V/ns
V/ns
(1)
tCLCH
0.1
(1)
tCHCL
0.1
For read mode
45% fC
tCKH
SCK High Time
For others
ns
ns
45% fCT/C2/T2/Q2
For read mode
45% fC
tCKL
SCK Low Time
For others
45% fCT/C2/T2/Q2
tCEH
tCS
CE# High Time
CE# Setup Time
CE# Hold Time
7
5
ns
ns
ns
tCH
5
Normal Mode
Data In Setup Time
2
tDS
ns
ns
ns
DTR Mode
1.5
2
Normal Mode
Data in Hold Time
tDH
DTR Mode
1.5
@ 133MHz (CL = 15pF)
Output Valid
7
8
tV
@ 104MHz (CL = 30pF)
tOH
Output Hold Time
2
ns
ns
ns
ns
ns
ns
ns
ns
ms
s
(1)
tDIS
Output Disable Time
8
tHLCH
tCHHH
tHHCH
tCHHL
HOLD Active Setup Time relative to SCK
HOLD Active Hold Time relative to SCK
HOLD Not Active Setup Time relative to SCK
HOLD Not Active Hold Time relative to SCK
HOLD to Output Low Z
2
2
2
2
(1)
tLZ
12
12
300
0.5
1.0
1.7
3
(1)
tHZ
HOLD to Output High Z
Sector Erase Time (4Kbyte)
Block Erase Time (32Kbyte)
Block Erase time (64Kbyte)
2Mb(4)
70
0.1
0.15
0.5
1
s
tEC
Chip Erase Time
4Mb(4)
s
8Mb
2
6
tPP
Page Program Time
0.2
0.8
ms
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
94
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Symbol
Parameter
Min
Typ(3)
Max
Units
IS25LP
3
(1)
tRES1
Release deep power down
µs
IS25WP
5
(1)
tDP
Deep power down
3
µs
ms
µs
µs
µs
µs
tW
Write Status Register time
Suspend to read ready
2
15
100
100
(1)
tSUS
(1)
tSRST
Software Reset recovery time
RESET# pin low pulse width
Hardware Reset recovery time
(1)
tRESET
1(2)
(1)
tHWRST
100
Notes:
1. These parameters are characterized and not 100% tested.
2. If the RESET# pulse is driven for a period shorter than 1µs (tRESET minimum), it may still reset the device, however
the 1µs minimum period is recommended to ensure reliable operation.
3. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC
= VCC (Typ), TA=25°C.
4. 4Mb/2Mb are available only for 1.8V device.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
95
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
9.7 SERIAL INPUT/OUTPUT TIMING
Figure 9.2 SERIAL INPUT/OUTPUT TIMING (Normal Mode) (1)
tCEH
CE#
tCS
tCH
tCKH
tCKL
SCK
SI
tDS
tDH
VALID IN
VALID IN
tV
tOH
VALID OUTPUT
tDIS
HI-Z
HI-Z
SO
Note1: For SPI Mode 0 (0,0)
Figure 9.3 SERIAL INPUT/OUTPUT TIMING (DTR Mode) (1)
tCEH
CE#
tCS
tCH
tCKH
tCKL
SCK
SI
tDS
tDH
VALID IN
VALID IN
VALID IN
tDIS
tOH
tV
tV
HI-Z
HI-Z
SO
Output
Output
Note1: For SPI Mode 0 (0,0)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
96
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Figure 9.4 HOLD TIMING
CE#
tHLCH
tCHHL
tHHCH
SCK
tCHHH
tHZ
tLZ
SO
SI
HOLD#
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
97
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
9.8 POWER-UP AND POWER-DOWN
At Power-up and Power-down, the device must be NOT SELECTED until Vcc reaches at the right level. (Adding a
simple pull-up resistor on CE# is recommended.)
Power up timing
VCC
VCC(max)
Chip Selection Not Allowed
VCC(min)
Device is fully
accessible
t
VCE
= Vcc min. to CE# Low
VWI
Time
Symbol
tVCE(1)
Parameter
Min.
300
Max
Unit
us
Vcc(min) to CE# Low
Write Inhibit Voltage
IS25LP
2.1
1.4
(1)
VWI
V
IS25WP
Note: These parameters are characterized and not 100% tested.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
98
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
9.9 PROGRAM/ERASE PERFORMANCE
Parameter
Typ
70
0.1
0.15
0.5
1
Max
300
0.5
1.0
1.7
3
Unit
ms
s
Sector Erase Time (4Kbyte)
Block Erase Time (32Kbyte)
Block Erase Time (64Kbyte)
s
2Mb
4Mb
8Mb
Chip Erase Time
s
2
6
Page Programming Time
Byte Program
0.2
8
0.8
40
ms
µs
Note: These parameters are characterized and not 100% tested.
9.10 RELIABILITY CHARACTERISTICS
Parameter
Endurance
Min
100,000
20
Max
Unit
Test Method
-
-
Cycles
Years
mA
JEDEC Standard A117
JEDEC Standard A117
JEDEC Standard 78
Data Retention
Latch-Up
-100
+100
Note: These parameters are characterized and not 100% tested.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
99
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.PACKAGE TYPE INFORMATION
10.1 8-PIN JEDEC 208MIL BROAD SMALL OUTLINE INTEGRATED CIRCUIT (SOIC) PACKAGE (B)
Note: Lead co-planarity is 0.1mm.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
100
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.2 8-PIN JEDEC 150MIL BROAD SMALL OUTLINE INTEGRATED CIRCUIT (SOIC) PACKAGE (N)
Note: Lead co-planarity is 0.08mm.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
101
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.3 8-PIN 150MIL VVSOP PACKAGE (V)
Note: Lead co-planarity is 0.08mm.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
102
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.4 8-CONTACT ULTRA-THIN SMALL OUTLINE NO-LEAD (USON) PACKAGE 2X3MM (U)
Note: Lead co-planarity is 0.08mm.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
103
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.5 8-CONTACT ULTRA-THIN SMALL OUTLINE NO-LEAD (USON) PACKAGE 4X3MM (T)
Note: Lead co-planarity is 0.08mm.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
104
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
10.6 8-CONTACT ULTRA-THIN SMALL OUTLINE NO-LEAD (WSON) PACKAGE 6X5MM (K)
Note: Lead co-planarity is 0.08mm.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
105
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
11.ORDERING INFORMATION - Valid Part Numbers
IS25LP 080 D
-
J
B
L
E
TEMPERATURE RANGE
E = Extended (-40°C to +105°C)
E1 = Extended+ (-40°C to +125°C) (Call Factory)
A1 = Automotive Grade (-40°C to +85°C)
A2 = Automotive Grade (-40°C to +105°C)
A3 = Automotive Grade (-40°C to +125°C)
PACKAGING CONTENT
L = RoHS compliant
PACKAGE Type (1)
B = 8-pin SOIC 208mil
N = 8-pin SOIC 150mil
V = 8-pin VVSOP 150mil
T = 8-contact USON 4x3mm
U = 8-contact USON 2x3mm
K = 8-contact WSON 6x5mm
W = KGD (Call Factory)
Option
J = Standard
Die Revision
D = Revision D
Density
080 = 8 Megabit
040 = 4 Megabit (Call Factory)
020 = 2 Megabit (Call Factory)
BASE PART NUMBER
IS = Integrated Silicon Solution Inc.
25LP = FLASH, 2.30V ~ 3.60V, QPI
25WP = FLASH, 1.65V ~ 1.95V, QPI
Note:
1. Call Factory for other package options available
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
106
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Density,
Voltage
Frequency (MHz)
Order Part Number(1)
Package
IS25LP080D-JBLE
IS25LP080D-JBLE1(2)
IS25LP080D-JNLE1(2)
IS25LP080D-JVLE1(2)
IS25LP080D-JKLE1(2)
IS25LP080D-JTLE1(2)
IS25LP080D-JULE1(2)
8-pin SOIC 208mil
8-pin SOIC 150mil
IS25LP080D-JNLE
IS25LP080D-JVLE
IS25LP080D-JKLE
IS25LP080D-JTLE
IS25LP080D-JULE
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 4x3mm
8-contact USON 2x3mm
8-pin SOIC 208mil
8Mb,
3V
STR 133,
DTR 66
IS25LP080D-JBLA*(1)
IS25LP080D-JNLA*(1)
IS25LP080D-JVLA*(1)
IS25LP080D-JKLA*(1)
IS25LP080D-JTLA*(1)
IS25LP080D-JULA*(1)
IS25LP080D-JWLE(2)
8-pin SOIC 150mil
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 4x3mm
8-contact USON 2x3mm
KGD
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
107
09/02/2016
IS25LP080D
IS25WP080D/040D/020D
Density,
Voltage
Frequency (MHz)
Order Part Number
Package
IS25WP080D-JBLE
IS25WP080D-JBLE1(2)
IS25WP080D-JNLE1(2)
IS25WP080D-JVLE1(2)
IS25WP080D-JKLE1(2)
IS25WP080D-JTLE1(2)
IS25WP080D-JULE1(2)
8-pin SOIC 208mil
8-pin SOIC 150mil
IS25WP080D-JNLE
IS25WP080D-JVLE
IS25WP080D-JKLE
IS25WP080D-JTLE
IS25WP080D-JULE
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 4x3mm
8-contact USON 2x3mm
8-pin SOIC 208mil
8Mb,
1.8V
STR 133,
DTR 66
IS25WP080D-JBLA*(1)
IS25WP080D-JNLA*(1)
IS25WP080D-JVLA*(1)
IS25WP080D-JKLA*(1)
IS25WP080D-JTLA*(1)
IS25WP080D-JULA*(1)
IS25WP080D-JWLE*(2)
8-pin SOIC 150mil
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 4x3mm
8-contact USON 2x3mm
KGD
IS25WP040D-JBLE(2)
IS25WP040D-JBLE1(2)
IS25WP040D-JNLE1(2)
IS25WP040D-JVLE1(2)
IS25WP040D-JKLE1(2)
IS25WP040D-JTLE1(2)
IS25WP040D-JULE1(2)
8-pin SOIC 208mil
IS25WP040D-JNLE(2)
IS25WP040D-JVLE(2)
IS25WP040D-JKLE(2)
IS25WP040D-JTLE(2)
IS25WP040D-JULE(2)
8-pin SOIC 150mil
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 4x3mm
8-contact USON 2x3mm
8-pin SOIC 208mil
4Mb,
1.8V
STR 133,
DTR 66
IS25WP040D-JBLA*(1, 2)
IS25WP040D-JNLA*(1, 2)
IS25WP040D-JVLA*(1, 2)
IS25WP040D-JKLA*(1, 2)
IS25WP040D-JTLA*(1, 2)
IS25WP040D-JULA*(1, 2)
IS25WP040D-JWLE(2)
8-pin SOIC 150mil
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 4x3mm
8-contact USON 2x3mm
KGD
IS25WP020D-JBLE(2)
IS25WP020D-JBLE1(2)
IS25WP020D-JNLE1(2)
IS25WP020D-JVLE1(2)
IS25WP020D-JKLE1(2)
IS25WP020D-JULE1(2)
8-pin SOIC 208mil
IS25WP020D-JNLE(2)
IS25WP020D-JVLE(2)
IS25WP020D-JKLE(2)
IS25WP020D-JULE(2)
8-pin SOIC 150mil
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 2x3mm
8-pin SOIC 208mil
2Mb,
1.8V
STR 133,
DTR 66
IS25WP020D-JBLA*(1, 2)
IS25WP020D-JNLA*(1, 2)
IS25WP020D-JVLA*(1, 2)
IS25WP020D-JKLA*(1, 2)
IS25WP020D-JULA*(1, 2)
IS25WP020D-JWLE*(2)
8-pin SOIC 150mil
8-pin VVSOP 150mil
8-contact WSON 6x5mm
8-contact USON 2x3mm
KGD
Notes:
1. A* = A1, A2, A3: Meets AEC-Q100 requirements with PPAP, E1= Extended+ non-Auto qualified
Temp Grades: E= -40 to 105°C, E1= -40 to 125°C, A1= -40 to 85°C, A2= -40 to 105°C, A3= -40 to 125°C
2. Call Factory
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
108
09/02/2016
相关型号:
©2020 ICPDF网 联系我们和版权申明