SLC10P500 [ITT]
Snap/Clip-Lock Environmentally Sealed - Circular; 捕捉/剪锁密封环境 - 圆型号: | SLC10P500 |
厂家: | ITT Cannon |
描述: | Snap/Clip-Lock Environmentally Sealed - Circular |
文件: | 总16页 (文件大小:445K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Snap/Clip-Lock Environmentally Sealed - Circular
Engineering Quick Reference Selection Guide
4 Position
5 Position
2 Position
Plug
Receptacle
Plug
Receptacle
Contact
Arrangement
Contact
Cannon
2
2
1
3
3
1
1
2
2
1
5
4
4
5
Inline
Feed Thru
Clip Lock
CS-216
Inline
PCB
Inline
Features
Specifications
Plug
Clip Lock
CS-216
Clip Lock
CS-216
Snap Lock
CS-206
Snap Lock
CS-206
086-0066-000 w/Wedgelock
086-0058-000 Standard
Contact
Cannon
098532-0000 (5 A)
098532-001 (13 A)
098532-0000 (5 A)
098532-001 (13 A)
086-0058-000 Standard
Contact
Cannon
098531-0000 (5 A)
098531-0001 (13 A)
098530-0000 (5 A)
098530-0001 (13 A)
086-0061-000 w/Wedgelock
See page 14
083-0242-000
See page 14
Receptacle
Terminals
Contact Cannon
See page 14
See page 14
How to Order
SLC
5
T
13
0
0
Series Prefix
Size/Configuration
Connector Type
Contact Termination
Material/Finish Modifier
Mechanical Modifier
Series Prefix
SLC - Snap-Lock Circular
Contact Termination
5 - 5 A
13 - 13 A
Size/Configuration
5-5 Cavity Housing
8-8 Cavity Housing
10-10 Cavity Housing
15-15 Cavity Housing
Material/Finish Modifier
0 -Standard Assembly (Silicone Elastomer)
1 -Fluorosilicone Elastomer
Mechanical Modifier
Connector Type
0 -Standard Assembly
P - Plug, In-line (Cable-to-Cable)*
R - Receptacle, In-line (Cable-to-Cable)
T - Receptacle, Snap-thru
B - Receptacle, PCB
*Note: In-line Plug mates with all 3 receptacle types (In-line, Snap-thru, and PCB.)
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
4
Snap/Clip-Lock Environmentally Sealed - Circular
Engineering Quick Reference Selection Guide
Plug
Receptacle
15 Position
10 Position
8 Position
Receptacle
Receptacle
4
3
Plug
Plug
12
15
3
4
12
13
11
5
11
10
3
4
3
2
13
4
14
2
2
1
5
2
1
2
2
1
5
10
14
6
5
10
9
7
1
10
15
1
3
4
8
8
5
6
3
7
1
9
8
9
8
8
6
6
9
6
6
4
5
7
7
8
7
7
Snap-thru
PCB
Inline
Snap-thru
PCB
Inline
Snap-thru
Snap Lock
(Double)
Snap Lock
(Double)
Snap Lock
(Double)
Snap Lock
(Double)
Snap Lock
(Double)
Snap Lock
(Double)
Snap Lock (Double)
CS-210
CS-206
CS-206
CS-210
CS-210
CS-210
CS-210
098532-0002 (5 A) 098532-0002 (5 A)
098532-0003 (13 A) 098532-0003 (13 A) 098532-0003 (13 A)
098532-0002 (5 A)
086-0060-000
098532-0010
098532-0008
098532-0010
098531-0002 (5 A) 098530-0002 (5 A)
098531-0003 (13 A) 098530-0003 (13 A)
098533-0002
098533-0003
086-0059-000
See page 14
098533-0010
-
-
See page 14
See page 14
See page 14
See page 14
See page 14
See page 14
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
5
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
The Snap Lock Environmental Series is
environmentally sealed connector created for printed
circuit board, black box, cable-to-cable or bulkhead
applications.
When your under-the-hood requirements call for
tough performance, the SLC "snaps" into a tightly
sealed connection that can withstand heat, shock and
vibration. The connector is designed to preserve the
integrity of the solid state package, while protecting
against contaminants - even when unmated.
Gold, tin/lead plated stamped contacts add durability.
A rugged, thermoplastic receptacle body maximizes
performance by withstanding temperature variances
from -40°C to +150°C (material rating).
The SLC series is available in 2, 5, 8, 10, 15 contact
cavity configurations. It can also be adapted to
robotics assembly. Should you requirement demand
higher density configurations, consult Customer
Service.
Product Features and Benefits
· Superior environmental sealing
· Material rating: -40°C to +150°C continuous
operation at rated current
· Current rating 5 A and 13 A versions
· Low millivolt drop
· Low contact resistance
· Latch with tactile and audible feedback
· Increases durability and provides for minimum
installation
· Available in sizes 2, 5, 8, 10, 15 contacts
· Crimp stamped gold, tin/lead plated contacts
· Hand insertable/removable contacts
· Small footprint on P.C. board and low profile
· Adaptable to robotics assembly
· Low installed cost
· Requires less PCB space
Performance Specifications
Contact Resistance 10mΩ maximum
Insulation Resistance 20MΩ minimum (USCAR)
Current Rating 5 A signal continuous at 150°C all contacts, 2 position
13 A power continuous at 150°C all contacts, 5 position and 10 position only
Dielectric Withstanding Voltage 1000 Vrms AC at sea level
Applicable Cannon Specification SLC (CS-206) SLCT 5 & 10 (210) SLCT8 (216) SLCT 15 (206)
Material Rating Operating Temperature -40°C to +150°C
Crimp Contacts Semi-automatic or hand crimpable or fully automatic
Wire Size 20 - 16 AWG
Wire Insulation Sealing Range 1,98 (.078) to 3,30 (.130) dia.
Contact Insertion No tool required. Suitable for automation.
Contact Extraction Rear Removable
Contact Retention 20 lbs. Minimum per contact
Wire Strip Length 5,59 (.220) to 5,33 (.210)
Materials and Finishes
Connector Housing High temperature thermoplastic
Contacts Copper alloy
Finish Engaging area: Gold over nickel
Crimp/P.C. tail area: Tin/lead over nickel - standard offering
Tin/Lead over nickel - Option #2 all over
Environmental Seal High temperature silicone elastomer
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
6
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Contact Cavity Arrangements - Mating Face View
Plug
2
1
2
1
7
3
8
5
3
6
1
2
5
4
4
2 Way
5 Way
8 Way
3
4
3
12
4
11
10
2
2
13
5
5
1
10
9
14
6
15
6
1
9
8
8
7
7
10 Way
15 Way
Receptacle
2
2
1
3
1
3
7
8
2
1
4
4
5
6
5
2 Way
5 Way
8 Way
3
4
3
4
12
11
2
2
13
1
5
10
9
5
10
14
6
15
6
1
9
8
8
7
7
10 Way
15 Way
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
7
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Plug, In-line* (Cable-to-Cable) (Type P) SLC-5, SLC-10
Side View
Plug Assembly
Front-Face View
10 Cavity Housing
Front-Face View
5 Cavity Housing
In-line Plug* (Mates with SLC types R, T, and B)
Housing Size
Rating
5 A
Part Number
098532-0011
098532-0001
098532-0002
098532-0003
Description
A
ØB
5
SLC-5P5-00
SLC-5P13-00
SLC-10P5-00
SLC-10P13-00
27,81 (1.095)
26,80 (1.055)
34,92 (1.375)
34,04 (1.340)
18,03 (.710)
18,03 (.710)
24,15 (.990)
25,15 (.990)
5
13 A
5 A
10
10
13 A
*Contact lead assemblies are customer terminated and installed. See page 14, part numbers 110238-0488, 110238-2003.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
8
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Receptacle, In-line* (Cable-to-Cable) (Type R) SLC-5, SLC-10
Side View
Receptacle Assembly
Front-Face View
10 Cavity Housing
Front-Face View
5 Cavity Housing
In-line Receptacle* (Mates with SLC type P)
Housing Size
Rating
5 A
Part Number
098530-0000
098530-0001
098530-0002
098530-0003
Description
A
ØB
C Ref.
5
SLC-5R5-00
SLC-5R13-00
SLC-10R5-00
SLC-10R13-00
24,13 (.950)
23,75 (.935)
31,24 (1.230)
30,86 (1.215)
18,03 (.710) 24,38 (.960)
18,03 (.710) 24,38 (.960)
25,15 (.990) 31,62 (1.245)
25,15 (.990) 31.62 (1.245)
5
13 A
5 A
10
10
13 A
*Contact lead assemblies are customer terminated and installed. See page 16, part numbers 110238-0446, 110238-2004.
Square Flange
Snaps onto Type R and B connectors
Materials and Finishes
Material: Thermoplastic
Color: Black
Housing Size
Part Number
066-9504.000
A
B Max.
ØC
5
23,37 (.920)
31,24 (1.230)
36,32 (1.430)
32,51 - 31,75 (1.280 - 1.250)
25,40 - 24,64 (1.000 - .970)
10
066-9504-001 28,45 (1.120)
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
9
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Receptacle, Snap-thru* (Type T) SLC-5, SLC-10
Side View
Front-Face View
10 Position
Front-Face View
5 Position
Panel Rear
Face View
Panel Section View
Snap-thru Receptacle* (Mates with SLC Type P)
Housing Size
Rating
5 A
Part Number
098533-0000
098533-0001
098533-0002
098533-0003
Description
ØA
ØB
ØC
ØD
5
SLC-5T5-00
SLC-5T13-00
SLC-10T5-00
37,21 (1.465)
36,96 (1.455)
47,62 (1.875)
24,13 (.950)
23,75 (.935)
31,24 (1.230)
30,86 (1.215)
25,60 (1.008)
25,48 (1.003)
35,05 (1.380)
34,92 (1.375)
15,62 (.615)
15,34 (.605)
20,19 (.795)
19,94 (.785)
5
13 A
5 A
10
10
13 A
SLC-10T13-00 47,37 (1.865)
*Contact lead assemblies are customer terminated and installed. See page 14, part numbers 110238-0446, 110238-2004.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
10
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Receptacle, PCB* (Type B) SLC-5, SLC-10
Front-Face View
5 Cavity Housing
Front-Face View
10 Cavity Housing
Side View
In-Line Receptacle
With PCB Contacts
In-line Receptacle* (Mates with SLC Type P)
Size
5
Rating Part Number
Description
A
ØB
C Ref.
5 A
098531-0000
098531-0001
098531-0002
098531-0003
SLC-5B5-00
SLC-5B13-00
SLC-10B5-00
SLC-10B13-00
24,13 (.950)
23,75 (.935)
31,24 (1.230)
30,86 (1.215)
18,03 (.710)
18,03 (.710)
25,15 (.990)
25,15 (.990)
24,38 (.960)
24,38 (.960)
31,62 (1.245)
31,62 (1.245)
5
13 A
5 A
10
10
13 A
*PCB Contacts are factory installed.
Recommended PCB Layout
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
11
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Receptacle, Snap-thru SLCT-8
48,26
Part No.: 098533-0010 (mates with 098532-0008)
(1.900)
27,56
(1.085)
Receptacle, Feed-thru CLC-2
Part No.: 086-0057-000
13,85
(.550)
STRAIGHT
PIPE THREAD
SEALED
INTERFACE
20,30
(.800)
fl
SEALED
INTERFACE
10,10
(.400)
4,45
(.175)
22,90
(.900)
PANEL
MAX
15,90
(.600)
Note: In-line plug and receptacle available.
44,00
(1.700)
Plug, Feed-thru CLC-2
Part No.: 086-0058-000
With Silicone Grommet Seal
Part No.: 086-0058-001
With Silicone Grommet Seal
Part No.: 086-0058-002
With Fluorosilicone Seal
32,26
(1.270)
23,00
(.900)
13,20
(.520)
16,60
(.650)
A
B
4,45
(.175)
19,30
(.760)
Right Angle CLC and CLC Y-Splice, please contact Product Management.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
12
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Plug, Snap-thru SLC-15
Part Number: 086-0060-000
Receptacle, Snap-thru SLC-15
Part Number: 086-0059-000
Consult factory for alternate layouts.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
13
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Contacts, Stamped, 5 and 13 Amp
Socket (use in plugs)
Hooded Socket
Pin (use in receptacles)
Hooded Socket
Reeled
Description
5 A
13 A
Socket Part Number
110238-1016 (030-2480-007)
Pin Part Number
110238-0446 (030-2464-007)
110238-2004 (030-2464-003)
Socket Part Number
110238-0488 (030-2480-000)
110238-2003 (030-2480-003)
Number of Contacts
4,500
4,000
Accessories
Sealing Plugs
Connector Clip
Material: Thermoplastic, Color: Natural
Part Number: 225-0093-000
+125°C Rating
Material: Thermoplastic, Color: Natural
Part Number: 225-0093-000
+125°C Rating
Mounting Hardware for use on In-line Receptacle
(Cable-to-Cable) (Type R)
Fits Ø6,35 (.250) hole x 0,51 (.020) thick panel.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
14
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Extraction Tool
Contact Extraction Tool
Part Number: 274-7068-001
Tip Part Number: 323-9519-000
A Standard CET - SLE/SLC is available for extraction of the
individual crimp contacts. Insertion tool is not required.
Insertion / Extraction Instructions for Crimp Contacts
Insertion Tool
No insertion tool is required. The
contact is easily snapped in
from the rear of the connector
manually.
1. Move to the rear of the
connector so that the contact
cavities can be identified.
2. Insert a crimp terminated
assembly into a selected cavity.
3. Continue the forward movement
until and audible snap can be felt
and heard. Slight pull in the
opposite direction will confirm
complete insertion.
Extraction
1. Open the CET - SLC Extraction
tool and place it over the insulation
of the wire.
2. Using a straight motion forward,
insert the tool along the wire until it
bottoms against the connector. (Do
not use a screwing motion -
damage will result.)
3. While the extraction tool is in
place, simply pull the wire/contact
assembly out.
4. Remove the extraction tool.
Extraction is complete.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
15
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Hand Crimp Tool Operation
Hand Crimp Tool - CCT - SLC / SLE
Part Number: 995-0002-232
The CCT-SLC/SLE hand crimp tool is designed to crimp individual SLC/SLE contacts on wire sizes 16, 18, and 20 AWG.
Each cycle is ratchet-controlled (The tool must be completely closed before it can be reopened) to assure a satisfactory
crimp each time. Over and under crimps are eliminated.
This tool is for use when the requirement is for low to moderate volume quantities, and for on-site applications where semi-
automatic tools cannot be practically used.
1. Cycle the CCT - SLE / SLC hand tool to the open
position.
2. While pressing upward on the locator spring, insert
the contact with tails upward completely into the
locator.
3. When correctly positioned the contact should be
located beyond flush with the edge of the CCT - SLE
/ SLC and positioned in the concave polished split
level crimp.
4. Partially (usually the first click) Cycle the hand tool
assuring that the upward thrusting tails of the contact
has started engaging with the top jaw of the tool.
(There is a slight tendency for the contact to roll out
of vertical alignment.)
5. Insert the pre-stripped wire into the crimp area of
the contact and completely cycle the tool.
6. While pressing upward on the locator spring
withdraw the crimp termination.
Wire Stripping
5 and 13 A Contact
7. The result will be a perfect termination.
8. Note that there are no unterminated wire strands,
and that some strand ends can be seen at the
forward edge of the crimp. Also note the insulation is
gripped by the smaller secondary crimp. Distortion is
at a minimum, both axially and laterally - no sharp
edges.
Tolerance
Low
High
A
B
2,41 (.095)
3,30 (.130)
5,33 (.210)
5,59 (.220)
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
16
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Lease Automatic Tooling - North America*
ABT-607 Pneumatic Crimper
The ABT-607 is a pneumatic powered and controlled
Machine Crimp Rate:
machine. It is designed for customers with moderate
volume. This machine is designed to semi-
automatically crimp stamped and formed contacts
onto pre-stripped stranded or single conductor
electrical wire. This machine will accommodate size
34 thru 12 AWG wire and is actuated by the use of a
foot pedal.
800 per hour
Power Requirements:
Pneumatic = 100 psi, 2 cu. ft. per min.
ABT-500 UCCD
The ABT-500 Universal Cannon Crimp Die, is a
flywheel driven, electronically controlled machine that
is designed to semi-automatically crimp stamped and
Machine Crimp Rate:
1300 per hour
formed contacts on stranded or single conductor, pre- Power Requirements:
stripped wire. This machine will accommodate size
34 thru 12 WG wire. The machine is actuated by the
use of a foot pedal.
Electrical = 115VAC, 60Hz, 20A
ABT-620 UCCS
The ABT-620 Universal Cannon Crimper/Stripper is a
pneumatic powered, microprocessor controlled
machine. It is designed to semi-automatically strip
insulation from stranded or single conductor electrical
wire and attach a stamped and formed contact by
crimping. The machine will accommodate 34 thru 12
AWG wire. Primary application of the machine is the
termination of jacketed cable where the individual
leads cannot be stripped by fully automated
Machine Crimp Rate:
1200+ per hour
Power Requirements:
Electrical = 115VAC, 60Hz, 20A
Pneumatic = 80 psi, 3 cu. ft. per min.
equipment. The ABT-620 UCCS operates
automatically upon insertion of a wire or it can be
switched over to foot pedal operation if desired.
* For other geographical regions, contact Cannon for details.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
17
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Crimp Pot Cross Section
D
CRIMP
WIDTH
C
CRIMP
HEIGHT
Crimp Height and Width
Wire Gauge (AWG)
18
CRIMP POT
CROSS SECTION
16
20
C*
.064*
.066*
D Ref.
.082
.082
C*
.056*
.062*
D Ref.
.080
.080
C*
.054*
.058*
D Ref.
.080
.080
Signal (5A)
Power (13A)
* Hand Tools are .002 and machines are .001
The wire crimp heights listed are only
reference and valid for the
correspondingly listed wire size, wire
plating and wire stranding.
The wire crimp tensile values must be
used to assure the performance of
crimped contacts.
Insulation Height and Width
Wire Gauge (AWG)
18
16
20
For wire crimp information not listed in
this table, please contact Cannon.
Height
Max
Width
Max**
.115**
.115**
Height
Max
.105
Width
Max**
.110**
.110**
Height
Max
.105
Width
Max**
.110**
.110**
Signal (5A)
.110
Power (13A)
.110
.105
.105
** Measurements are taken without crimping wire insulation.
Crimp Tensile Strength
Wire Trim Dimension
(.220 - .210)
(.130 - .095)
Wire Size (AWG)
Tensile Min (lbs)
16
35 lbs.
18
25 lbs.
20
20lbs.
Dimensions shown in mm
Specifications and dimensions subject to change
www.ittcannon.com
18
Cannon SLC/SLC-T/CLC
Snap/Clip-Lock Environmentally Sealed - Circular
Test Parameters
SLC Products are designed to meet Cannon specifications CS-206, CS-210, and CS-216. Items of most general interest to users are designers are listed below.
Test
Description
Reference
Paragraph
Requirements
Environmental
Sealing
3.2.3.5
3.2.3.6
3.2.3.7
3.2.3.8
3.2.3.9
3.2.3.2
Sand and Dust MIL-STD-202 Method 110 Test Condition A
5% salt spray 96 hours
10 cycles of 24 hours, 90-98% humidity
Steam Cleaning/Pressure Wash 95°C, 375 Cycles 750 PSIG
Solvent Resistance/Immersion (see 3.2.3.9)
Thermal Shock 100 Cycles -40°C to +150°C 3°C
Contact Crimp
Tensile Strength
3.2.2.1
The minimum tensile load required to separate the wire from the contact, either by pulling the wire out of the crimp joint or by
breaking the wire within the crimp joint shall not be less than the applicable limits as specified. Wire breakage or contact damage
not due to crimping at less than tensile loads shall not constitute a failure.
Wire Size AWG
Crimp Tensile Strength, Pounds Minimum
16
18
20
35
25
20
Insulation
Resistance
3.2.1.1
3.2.1.2
3.2.1.4
3.2.3.3
Mated and wired connectors shall exhibit an insulation resistance greater than 100 megohms between all contacts. This limit
shall apply after exposure to each environment including salt solution immersion. Tests shall be performed at 100 VDC 10%.
Dielectric
Withstanding
Voltage
Low Level
Contact
Resistance
Mechanical
Shock
Wired and mated connectors shall show no evidence of breakdown between adjacent contacts when tested at 1000 VDC 5%.
Connectors shall meet this requirement after exposure to each environment. Current leakage shall be less than 1.0 milliamp.
The low level contact resistance of mated contacts shall be less than 10 milliohms when measured across the contacts and
crimp joints. The test current shall be a maximum of 100 milliamps with an open circuit test voltage of 20 millivolts maximum.
Connectors shall be subjected to three shocks in each direction applied along the three mutually perpendicular axes of the
connector test specimen for a total of 12 shocks. Each shock shall consist of a terminal peak sawtooth pulse with a peak value
of 100 g's and a duration of 6 milliseconds.
Vibration
3.2.3.4
Connectors shall be subjected to random vibration in accordance with MIL-STD-1344, Method 2005.1, test condition VI for 20
hours along each of the following three axes:
Direction
Radial axis of connector (Y)
Grms
10.2
Longitudinal axis of connector (Z)
10.2
Electrical continuity of the connectors shall be monitored during the last 20 minutes sweep in each axis with a test current of 100
milliamps or less and a test voltage less than 2VDC. Electrical discontinuities in excess of 10 microseconds shall be cause of
failure.
Durability
Contact
3.2.2.6
Connectors shall be subjected to 25 cycles of mating and unmating at room temperature. Following this test there shall be no
evidence of damage to the contacts, contact plating, connector housing or seals which may prove detrimental to reliable
performance of the connector.
3.2.2.2
3.2.2.3
3.2.2.4
3.2.2.9
Contacts shall not be displaced greater than 0.030 inches from the connector body when a force of 10 pounds is applied. When
this test follows maintenance again the same contacts shall be tested.
Maintenance
Aging
Consist of subjecting each wired receptacle to 5 cycles of removal and reinsertion of 20% of the contacts or a minimum of 5 per
connector with approved tooling.
Mating and
Separating
Force
Solvent
Resistance
Immersion
The maximum force required to mate the plug and receptacle shall be 10 pounds. The maximum force required to separate the
plug and receptacle shall be 5 pounds. The rate of travel shall be one inch per minute.
Connectors shall be subjected to the following fluids at the temperature and length of time specified. Following the fluid
dip or immersion, the connectors shall be immersed to a depth of 2 to 12 inches in a 5% salt-water solution for 24
hours at room temperature. At the completion of the salt-water immersion test, while still immersed, the connectors
shall meet the insulation resistance requirement specified herein.
Fluid
Method
Temperature
No. 2 Diesel Fluid
Methyl Alcohol
Antifreeze
Immersion (2)
Dip (1)
140°F
Room Temperature
- Prestone
Immersion (2)
Immersion (2)
180°F
180°F
- 50% Water/50%
Ethylene Glycol
Degreaser
- Gunk
Dip (1)
Dip (1)
Immersion (2)
Immersion (2)
Room Temperature
Room Temperature
Room Temperature
200°F
- Mineral Spirits
Paint (Oil Base)
Lubricating Oil
(SAE 10 W40)
Brake Fluid
Dip (1)
Room Temperature
Room Temperature
(Delco Supreme)
Transmission Fluid
Dip (1)
fully submerged and pressurized
@ 7 psi. (Dextron)
(1) Dip: Connectors shall withstand a one second dip and a three minute air dry for a total of 80 cycles.
(2) Immersion: Connectors shall withstand immersion for one hour.
Temperature
Life
3.2.3.1
3.2.3.2
Connectors shall be subjected to a temperature of 150°C 3°C for a period of 1000 hours. At the end of the temperature soak
period and after removal from the chamber, the connectors shall meet the insulation resistance and dielectric withstanding
voltage requirements specified herein. Connectors shall be operated at rated current throughout the duration of the temperature
life test. Upon removal from the chamber at the conclusion of the test, the connectors shall show no visual signs of damage,
which may be detrimental to the performance of the connector.
Thermal Cycling
Connectors shall be subjected to 100 thermal cycles from -40°C to +150°C. One cycle shall consist of the transitions from room
temperature to -40°C to +150°C, and from 150°C to room temperature. One cycle shall be accomplished in a three-hour period
with a minimum stabilization period of 15 minutes at each temperature extreme. The chamber temperature transition rate shall
be a minimum of 1.30°C per minute and a maximum of 6.00°C per minute.
Specifications and dimensions subject to change
www.ittcannon.com
19
相关型号:
SLC1175-121MEB
General Purpose Inductor, 0.12uH, 20%, 1 Element, Ferrite-Core, SMD, 4330, CHIP, 4330, HALOGEN FREE AND ROHS COMPLIANT
COILCRAFT
SLC1175-121MED
General Purpose Inductor, 0.12uH, 20%, 1 Element, Ferrite-Core, SMD, 4330, CHIP, 4330, HALOGEN FREE AND ROHS COMPLIANT
COILCRAFT
©2020 ICPDF网 联系我们和版权申明