C052C182F2G5TA7200_技术文档

MULTILAYER CERAMIC CAPACITORS/AXIAL

& RADIAL LEADED

Multilayer ceramic capacitors are available in a

edges of the laminated structure. The entire structure is

fired at high temperature to produce a monolithic

block which provides high capacitance values in a

small physical volume. After firing, conductive

terminations are applied to opposite ends of the chip to

make contact with the exposed electrodes.

Termination materials and methods vary depending on

the intended use.

variety of physical sizes and configurations, including

leaded devices and surface mounted chips. Leaded

styles include molded and conformally coated parts

with axial and radial leads. However, the basic

capacitor element is similar for all styles. It is called a

chip and consists of formulated dielectric materials

which have been cast into thin layers, interspersed

with metal electrodes alternately exposed on opposite

TEMPERATURE CHARACTERISTICS

Ceramic dielectric materials can be formulated with

a wide range of characteristics. The EIA standard for

ceramic dielectric capacitors (RS-198) divides ceramic

dielectrics into the following classes:

Class III: General purpose capacitors, suitable

for by-pass coupling or other applications in which

dielectric losses, high insulation resistance and

stability of capacitance characteristics are of little or

no importance. Class III capacitors are similar to Class

II capacitors except for temperature characteristics,

Class I: Temperature compensating capacitors,

suitable for resonant circuit application or other appli-

cations where high Q and stability of capacitance char-

acteristics are required. Class I capacitors have

predictable temperature coefficients and are not

affected by voltage, frequency or time. They are made

from materials which are not ferro-electric, yielding

superior stability but low volumetric efficiency. Class I

capacitors are the most stable type available, but have

the lowest volumetric efficiency.

which are greater than

15%. Class III capacitors

have the highest volumetric efficiency and poorest

stability of any type.

KEMET leaded ceramic capacitors are offered in

the three most popular temperature characteristics:

C0G: Class I, with a temperature coefficient of 0

30 ppm per degree C over an operating

temperature range of - 55°C to + 125°C (Also

known as “NP0”).

Class II: Stable capacitors, suitable for bypass

or coupling applications or frequency discriminating

circuits where Q and stability of capacitance char-

acteristics are not of major importance. Class II

capacitors have temperature characteristics of 15%

or less. They are made from materials which are

ferro-electric, yielding higher volumetric efficiency but

less stability. Class II capacitors are affected by

temperature, voltage, frequency and time.

X7R: Class II, with a maximum capacitance

change of 15% over an operating temperature

range of - 55°C to + 125°C.

Z5U: Class III, with a maximum capacitance

change of + 22% - 56% over an operating tem-

perature range of + 10°C to + 85°C.

Specified electrical limits for these three temperature

characteristics are shown in Table 1.

SPECIFIED ELECTRICAL LIMITS

Temperature Characteristics

X7R

Parameter

C0G

Z5U

Dissipation Factor: Measured at following conditions.

C0G – 1 kHz and 1 vrms if capacitance >1000pF

1 MHz and 1 vrms if capacitance 1000 pF

X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms

Z5U – 1 kHz and 0.5 vrms

2.5%

(3.5% @ 25V)

0.10%

4.0%

Dielectric Stength: 2.5 times rated DC voltage.

Pass Subsequent IR Test

1,000 M

or 100 G

F

1,000 M

or 100 G

F

1,000 M

or 10 G

F

Insulation Resistance (IR): At rated DC voltage,

whichever of the two is smaller

Temperature Characteristics: Range, °C

Capacitance Change without

DC voltage

-55 to +125

30 ppm/°C

-55 to +125

15%

+ 10 to +85

+22%,-56%

0

* MHz and 1 vrms if capacitance 100 pF on military product.

Table I

4

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

The variation of a capacitor’s impedance with frequency

determines its effectiveness in many applications.

ELECTRICAL CHARACTERISTICS

The fundamental electrical properties of multilayer

ceramic capacitors are as follows:

Dissipation Factor: Dissipation Factor (DF) is a mea-

sure of the losses in a capacitor under AC application. It is the

ratio of the equivalent series resistance to the capacitive reac-

tance, and is usually expressed in percent. It is usually mea-

sured simultaneously with capacitance, and under the same

conditions. The vector diagram in Figure 2 illustrates the rela-

tionship between DF, ESR, and impedance. The reciprocal of

the dissipation factor is called the “Q”, or quality factor. For

convenience, the “Q” factor is often used for very low values

of dissipation factor. DF is sometimes called the “loss tangent”

or “tangent ␦”, as derived from this diagram.

Polarity: Multilayer ceramic capacitors are not polar,

and may be used with DC voltage applied in either direction.

Rated Voltage: This term refers to the maximum con-

tinuous DC working voltage permissible across the entire

operating temperature range. Multilayer ceramic capacitors

are not extremely sensitive to voltage, and brief applications

of voltage above rated will not result in immediate failure.

However, reliability will be reduced by exposure to sustained

voltages above rated.

Capacitance: The standard unit of capacitance is the

farad. For practical capacitors, it is usually expressed in

ESR

Figure 2

-6

-9

microfarads (10 farad), nanofarads (10 farad), or picofarads

-12

(10 farad). Standard measurement conditions are as

O

ESR

follows:

DF =

X

c

Class I (up to 1,000 pF):

1MHz and 1.2 VRMS

maximum.

δ

X

Ζ

c

Class I (over 1,000 pF):

1kHz and 1.2 VRMS

maximum.

1

2πfC

=

X

Class II:

Class III:

1 kHz and 1.0 0.2 VRMS.

1 kHz and 0.5 0.1 VRMS.

c

Like all other practical capacitors, multilayer ceramic

capacitors also have resistance and inductance. A simplified

schematic for the equivalent circuit is shown in Figure 1.

Other significant electrical characteristics resulting from

these additional properties are as follows:

Insulation Resistance: Insulation Resistance (IR) is the

DC resistance measured across the terminals of a capacitor,

represented by the parallel resistance (Rp) shown in Figure 1.

For a given dielectric type, electrode area increases with

capacitance, resulting in a decrease in the insulation resis-

tance. Consequently, insulation resistance is usually specified

as the “RC” (IR x C) product, in terms of ohm-farads or

megohm-microfarads. The insulation resistance for a specific

capacitance value is determined by dividing this product by

the capacitance. However, as the nominal capacitance values

become small, the insulation resistance calculated from the

RC product reaches values which are impractical.

Consequently, IR specifications usually include both a mini-

mum RC product and a maximum limit on the IR calculated

from that value. For example, a typical IR specification might

read “1,000 megohm-microfarads or 100 gigohms, whichever

is less.”

R

Figure 1

P

R

L

S

C

C = Capacitance

L = Inductance

R

= Equivalent Series Resistance (ESR)

= Insulation Resistance (IR)

S

P

Impedance: Since the parallel resistance (Rp) is nor-

mally very high, the total impedance of the capacitor is:

Insulation Resistance is the measure of a capacitor to

resist the flow of DC leakage current. It is sometimes referred

to as “leakage resistance.” The DC leakage current may be

calculated by dividing the applied voltage by the insulation

resistance (Ohm’s Law).

2

R_S+ (X_C- X_L)²

Z =

Dielectric Withstanding Voltage: Dielectric withstand-

ing voltage (DWV) is the peak voltage which a capacitor is

designed to withstand for short periods of time without dam-

age. All KEMET multilayer ceramic capacitors will withstand a

test voltage of 2.5 x the rated voltage for 60 seconds.

Where Z =Total Impedance

RS = Equivalent Series Resistance

1

X_C= Capacitive Reactance =

2πfC

KEMET specification limits for these characteristics at

standard measurement conditions are shown in Table 1 on

page 4. Variations in these properties caused by changing

conditions of temperature, voltage, frequency, and time are

covered in the following sections.

X_L= Inductive Reactance = 2πfL

5

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

TABLE 1

EIA TEMPERATURE CHARACTERISTIC CODES

FOR CLASS I DIELECTRICS

Significant Figure

of Temperature

Coefficient

Multiplier Applied

to Temperature

Coefficient

Tolerance of

Temperature

Coefficient *

PPM per

Degree C

Letter

Symbol

Multi-

plier

Number

Symbol

PPM per

Degree C

Letter

Symbol

0.0

0.3

0.9

1.0

1.5

2.2

3.3

4.7

7.5

C

B

A

M

P

R

S

T

-1

-10

-100

-1000

-100000

+1

0

1

2

3

4

5

6

7

8

9

30

60

G

H

J

K

L

120

250

500

1000

2500

M

N

+10

+100

+1000

+10000

U

* These symetrical tolerances apply to a two-point measurement of

temperature coefficient: one at 25°C and one at 85°C. Some deviation

is permitted at lower temperatures. For example, the PPM tolerance

for C0G at -55°C is +30 / -72 PPM.

TABLE 2

EIA TEMPERATURE CHARACTERISTIC CODES

FOR CLASS II & III DIELECTRICS

Low Temperature

Rating

High Temperature Maximum Capacitance

Rating Shift

Degree

Celcius

Letter

Symbol Celcius

Degree

Number

Symbol

Letter

Symbol

Percent

+10C

-30C

-55C

Z

Y

X

+45C

+65C

+85C

+105C

+125C

+150C

+200C

2

4

5

6

7

8

9

1.0%

1.5%

2.2%

3.3%

4.7%

7.5%

10.0%

15.0%

22.0%

A

B

C

D

E

F

P

R

S

T

+10

+20

+30

+40

+50

+60

+70

+80

+22/-33%

+22/-56%

+22/-82%

U

V

6

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

At higher AC voltages, both capacitance and dissipation factor

begin to decrease.

Typical curves showing the effect of applied AC and DC

voltage are shown in Figure 6 for KEMET X7R capacitors and

Figure 7 for KEMET Z5U capacitors.

Effect of Frequency: Frequency affects both capaci-

tance and dissipation factor. Typical curves for KEMET multi-

layer ceramic capacitors are shown in Figures 8 and 9.

T

he variation of impedance with frequency is an impor-

tant consideration in the application of multilayer ceramic

capacitors. Total impedance of the capacitor is the vector of the

capacitive reactance, the inductive reactance, and the ESR, as

illustrated in Figure 2. As frequency increases, the capacitive

reactance decreases. However, the series inductance (L)

shown in Figure 1 produces inductive reactance, which

increases with frequency. At some frequency, the impedance

ceases to be capacitive and becomes inductive. This point, at

the bottom of the V-shaped impedance versus frequency

curves, is the self-resonant frequency. At the self-resonant fre-

quency, the reactance is zero, and the impedance consists of

the ESR only.

Typical impedance versus frequency curves for KEMET

multilayer ceramic capacitors are shown in Figures 10, 11, and

12. These curves apply to KEMET capacitors in chip form, with-

out leads. Lead configuration and lead length have a significant

impact on the series inductance. The lead inductance is

approximately 10nH/inch, which is large compared to the

inductance of the chip. The effect of this additional inductance

is a decrease in the self-resonant frequency, and an increase

in impedance in the inductive region above the self-resonant

frequency.

Effect of Time: The capacitance of Class II and III

dielectrics change with time as well as with temperature, volt-

age and frequency. This change with time is known as “aging.”

It is caused by gradual realignment of the crystalline structure

of the ceramic dielectric material as it is cooled below its Curie

temperature, which produces a loss of capacitance with time.

The aging process is predictable and follows a logarithmic

decay. Typical aging rates for C0G, X7R, and Z5U dielectrics

are as follows:

C0G

X7R

Z5U

None

2.0% per decade of time

5.0% per decade of time

Typical aging curves for X7R and Z5U dielectrics are

shown in Figure 13.

Effect of Temperature: Both capacitance and dissipa-

tion factor are affected by variations in temperature. The max-

imum capacitance change with temperature is defined by the

temperature characteristic. However, this only defines a “box”

bounded by the upper and lower operating temperatures and

the minimum and maximum capacitance values. Within this

“box”, the variation with temperature depends upon the spe-

cific dielectric formulation. Typical curves for KEMET capaci-

tors are shown in Figures 3, 4, and 5. These figures also

include the typical change in dissipation factor for KEMET

capacitors.

The aging process is reversible. If the capacitor is heat-

ed to a temperature above its Curie point for some period of

time, de-aging will occur and the capacitor will regain the

capacitance lost during the aging process. The amount of de-

aging depends on both the elevated temperature and the

length of time at that temperature. Exposure to 150°C for one-

half hour or 125°C for two hours is usually sufficient to return

the capacitor to its initial value.

Because the capacitance changes rapidly immediately

after de-aging, capacitance measurements are usually delayed

for at least 10 hours after the de-aging process, which is often

referred to as the “last heat.” In addition, manufacturers utilize

the aging rates to set factory test limits which will bring the

capacitance within the specified tolerance at some future time,

to allow for customer receipt and use. Typically, the test limits

are adjusted so that the capacitance will be within the specified

tolerance after either 1,000 hours or 100 days, depending on

the manufacturer and the product type.

Insulation resistance decreases with temperature.

Typically, the insulation resistance at maximum rated temper-

ature is 10% of the 25°C value.

Effect of Voltage: Class I ceramic capacitors are not

affected by variations in applied AC or DC voltages. For Class

II and III ceramic capacitors, variations in voltage affect only

the capacitance and dissipation factor. The application of DC

voltage higher than 5 vdc reduces both the capacitance and

dissipation factor. The application of AC voltages up to 10-20

Vac tends to increase both capacitance and dissipation factor.

7

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

capacitors may be operated with AC voltage applied without

need for DC bias.

POWER DISSIPATION

Power dissipation has been empirically determined for

two representative KEMET series: C052 and C062. Power dis-

sipation capability for various mounting configurations is shown

in Table 3. This table was extracted from Engineering Bulletin

F-2013, which provides a more detailed treatment of this sub-

ject.

Note that no significant difference was detected between

the two sizes in spite of a 2 to 1 surface area ratio. Due to the

materials used in the construction of multilayer ceramic capac-

itors, the power dissipation capability does not depend greatly

on the surface area of the capacitor body, but rather on how

well heat is conducted out of the capacitor lead wires.

Consequently, this power dissipation capability is applicable to

other leaded multilayer styles and sizes.

RELIABILITY

A well constructed multilayer ceramic capacitor is

extremely reliable and, for all practical purposes, has an infi-

nite life span when used within the maximum voltage and

temperature ratings. Capacitor failure may be induced by sus-

tained operation at voltages that exceed the rated DC voltage,

voltage spikes or transients that exceed the dielectric with-

standing voltage, sustained operation at temperatures above

the maximum rated temperature, or the excessive tempera-

ture rise due to power dissipation.

Failure rate is usually expressed in terms of percent per

1,000 hours or in FITS (failure per billion hours). Some

KEMET series are qualified under U.S. military established

reliability specifications MIL-PRF-20, MIL-PRF-123, MIL-

PRF-39014, and MIL-PRF-55681. Failure rates as low as

0.001% per 1,000 hours are available for all capacitance /

voltage ratings covered by these specifications. These spec-

ifications and accompanying Qualified Products List should

be consulted for details.

TABLE 3

POWER DISSIPATION CAPABILITY

(Rise in Celsius degrees per Watt)

Power

Dissipation

Mounting Configuration

For series not covered by these military specifications,

an internal testing program is maintained by KEMET Quality

Assurance. Samples from each week’s production are sub-

jected to a 2,000 hour accelerated life test at 2 x rated voltage

and maximum rated temperature. Based on the results of

these tests, the average failure rate for all non-military series

covered by this test program is currently 0.06% per 1,000

hours at maximum rated conditions. The failure rate would be

much lower at typical use conditions. For example, using MIL-

HDBK-217D this failure rate translates to 0.9 FITS at 50%

rated voltage and 50°C.

of C052 & C062

1.00" leadwires attached to binding post

of GR-1615 bridge (excellent heat sink)

90 Celsius degrees

rise per Watt 10%

0.25" leadwires attached to binding post

of GR-1615 bridge

55 Celsius degrees

rise per Watt 10%

Capacitor mounted flush to 0.062" glass-

epoxy circuit board with small copper traces

77 Celsius degrees

rise per Watt 10%

Capacitor mounted flush to 0.062" glass-

epoxy circuit board with four square inches

of copper land area as a heat sink

53 Celsius degrees

rise per Watt 10%

Current failure rate details for specific KEMET multilay-

er ceramic capacitor series are available on request.

As shown in Table 3, the power dissipation capability of

the capacitor is very sensitive to the details of its use environ-

ment. The temperature rise due to power dissipation should not

exceed 20°C. Using that constraint, the maximum permissible

power dissipation may be calculated from the data provided in

Table 3.

It is often convenient to translate power dissipation capa-

bility into a permissible AC voltage rating. Assuming a sinu-

soidal wave form, the RMS “ripple voltage” may be calculated

from the following formula:

MISAPPLICATION

Ceramic capacitors, like any other capacitors, may fail

if they are misapplied. Typical misapplications include expo-

sure to excessive voltage, current or temperature. If the

dielectric layer of the capacitor is damaged by misapplication

the electrical energy of the circuit can be released as heat,

which may damage the circuit board and other components

as well.

If potential for misapplication exists, it is recommended

that precautions be taken to protect personnel and equipment

during initial application of voltage. Commonly used precau-

tions include shielding of personnel and sensing for excessive

power drain during board testing.

P_MAX

E = Z x

R

Where E = RMS Ripple Voltage (volts)

P = Power Dissipation (watts)

Z = Impedance

STORAGE AND HANDLING

Ceramic chip capacitors should be stored in normal

working environments. While the chips themselves are quite

robust in other environments, solderability will be degraded

by exposure to high temperatures, high humidity, corrosive

atmospheres, and long term storage. In addition, packaging

materials will be degraded by high temperature – reels may

soften or warp, and tape peel force may increase. KEMET

recommends that maximum storage temperature not exceed

40˚ C, and maximum storage humidity not exceed 70% rela-

tive humidity. In addition, temperature fluctuations should be

minimized to avoid condensation on the parts, and atmos-

pheres should be free of chlorine and sulfur bearing com-

pounds. For optimized solderability, chip stock should be

used promptly, preferably within 1.5 years of receipt.

R = ESR

The data necessary to make this calculation is included in

Engineering Bulletin F-2013. However, the following criteria

must be observed:

1. The temperature rise due to power dissipation

should be limited to 20°C.

2. The peak AC voltage plus the DC voltage must not

exceed the maximum working voltage of the

capacitor.

Provided that these criteria are met, multilayer ceramic

8

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

EFFECT OF FREQUENCY

IMPEDANCE VS FREQUENCY

+0.2

+0.1

0

0.20

0.10

0.0

100

.001μF

.01μF

%ΔC

100

10

-0.1

%DF

10

-0.2

100

1

1K

10K

100K

1M

10M

0.001µF

1

Figure 8.

Frequency - Hertz

Capacitance & DF vs Frequency - C0G

0.01µF

0.1

0⁰.0^.01¹_0.1

1

0

100

1000

Frequency - MHz

Figure 10. Impedance vs Frequency

+5

0

10.0

7.5

5.0

2.5

0.0

0.001

for C0G Dielectric

0.1

1

10

100

1,000

%DF

Figure 10.

Frequency - MHz

%ΔC

-5

Impedance vs Frequency for C0G Dielectric

-10

-15

100

1K

10K

100K

1M

10M

0.1μF ^0.01µF

.01μF

Figure 9.

Frequency - Hertz

10

Capacitance & DF vs Frequency - X7R & Z5U

0.1µ

F

1

1.0 μF

1.0µF

1

0.1

0.01

0.1

1

1 0

100

1000

Frequency -MHz

Figure 11. Impedance vs Frequency

(hours)

EFFECT OF TIME

0.01

for X7R Dielectric

100%

98%

96%

94%

92%

X7R

0.001

0.1

1

10

100

1,000

Figure 11.

Frequency - MHz

90%

88%

100

Impedance vs Frequency for X7R Dielectric

86%

84%

Z5U

10

Z5U

82%

80%

100

0.1µF

1

78%

0.1μF

1.0µF

78%

76%

10

0.1

74%

1

0

1

0

1

0

1

0

K

100K

1.0 μF

0.01

Figure 13. Typical Aging Rates for X7R & Z5U

0.1

1

0

100

1000

1

Frequency -MHz

Figure 12. Impedance vs Frequency

for Z5U Dielectric

0.1

0.01

0.001

0.1

1

10

100

1,000

Figure 12.

Frequency - MHz

Impedance vs Frequency for Z5U Dielectric

9

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

ELECTRICAL

GENERAL SPECIFICATIONS

Working Voltage:

Capacitance:

Within specified tolerance and when measured with

1 volt rms at 1kHz (1000 pF or less at 1 MHz for C0G).

C0G – 50, 100, 200

X7R – 50, 100, 200

Dissipation Factor @25°C:

25°C at 1kHz (1000 pF or less at 1 MHz for C0G).

C0G – 0.15% maximum

Temperature Characteristics:

C0G 0 30 PPM / °C from -55°C to +125°C

X7R

15% from -55°C to +125°C

X7R – 2.5% maximum

Capacitance Tolerance:

Insulation Resistance:

C0G 0.5pF, 1%, 2%, 5%, 10%, 20%

( 0.5pF is tightest tolerance available)

X7R 10%, 20%, -0 +100%, +80% / -20%

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K M or 1000 M – F, whichever is less.

X7R – 100K M or 1000 M – F, whichever is less.

Construction:

Monolithic block of ceramic dielectric with

Interdigitated internal electrodes, encapsulated

in a molded case, and having axial or radial leads.

Meets flame test requirements of UL Standard 94V-0.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited

to 50 mA at 25°C.

Lead Material:

Axial: Solder coated copper clad steel

Radial: Solder-coated copper standard (100% tin

plated optional)

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for

5 1/2 seconds.

Terminal Strength:

EIA-198 Method 303, Condition A (2.2 kg)

27

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

CAPACITOR OUTLINE DRAWINGS — (AXIAL LEADS)

1.50 Min.

(38.10)

L

1.50 Min.

(38.10)

D

C

DIMENSIONS — INCHES (MILLIMETERS)

Case

Size

Military

Equivalent Styles

L

D

C

Length

Body diameter

Lead Diameter

CC75, CCR75

CK12, CKR11

C114

C124

C192

C202

C222

.160 ± .010 (4.06 ± .25)

.250 ± .010 (6.35 ± .25)

.390 ± .010 (9.91 ± .25)

.500 ± .020 (12.70 ± .51)

.690 ± .030 (17.53 ± .76)

.090 ± .010 (2.29 ± .25)

.140 ± .010 (3.56 ± .25)

.250 ± .015 (6.35 ± .38)

.350 ± .020 (8.89 ± .51)

.020, +.000, -.003 (.51, +.00, -.08)

CC76, CCR76

CK13, CKR12

.020, +.000, -.003 (.51, +.00, -.08)

.025, +.004, -.001 (.64, +.10, -.025)

CC77, CCR77

CK14, CKR14

CC78, CCR78

CK15, CKR15

CC79, CCR79

CK16, CKR16

CAPACITOR OUTLINE DRAWINGS — (RADIAL LEADS)

W

L

W

L

C052

C062,

C512,

C522

H

Lead Dia.

.025

.045

Max.

Lead Dia.

.025

1.25

Min.

1.25

Min.

(+.004

-.002)

(+.004

-.002)

Center Line of leads

within .030" of Center

Line of case.

S

DIMENSIONS — INCHES (MILLIMETERS)

S

Case

Size

Military

Equivalent Styles

H

L

W

Width

Lead

Height

Length

Spacing

CC05, CCR05

CK05, CKR05

C052

C062

.190 .010 ꢀ(.ꢁ8 .25ꢂ

.290 .010 ꢀꢃ.8ꢃ .25ꢂ

.190 .010 ꢀ(.ꢁ8 .25ꢂ

.290 .010 ꢀꢃ.8ꢃ .25ꢂ

.090 .010 ꢀ2.29 .25ꢂ

.200 .015 ꢀ5.0ꢁ .8ꢁꢂ

CC06, CCR06

CK06, CKR06

C512

C522

CC0ꢃ, CCR0ꢃ

CC0ꢁ, CCR0ꢁ

.(ꢁ0 .020 ꢀ12.19 .51ꢂ .(ꢁ0 .020 ꢀ12.19 .51ꢂ .1(0 .010 ꢀ8.56 .25ꢂ .(00 .020 ꢀ10.16 .51ꢂ

.(ꢁ0 .020 ꢀ12.19 .51ꢂ .(ꢁ0 .020 ꢀ12.19 .51ꢂ .2(0 .010 ꢀ6.10 .25ꢂ .(00 .020 ꢀ10.16 .51ꢂ

For packaging information, see pages 46, 47 and 48.

28

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

ORDERING INFORMATION

C 052 C 102 K

2

R

5

T

A

FAILURE RATE

CERAMIC

CASE SIZE

A – Not Applicable

LEAD MATERIAL

See Table Below

C – 60/(0 Tin/Lead ꢀSnPbꢂ

T – 100ꢄ Tin ꢀSnꢂꢀC052,

C062 onlyꢂ

SPECIFICATION

C – Standard

CAPACITANCE PICOFARAD CODE

Expressed in picofarads ꢀpFꢂ. First two digits represent

significant figures. Third digit specifies number of zeros

following except 9 indicates division by 10ꢂ. Examples:

0.1 µF = 100,000 pF = 10( and 9.1 pF = 919. See

tables for standard values.

INTERNAL CONSTRUCTION

5 – Multilayer

TEMPERATURE CHARACTERISTIC

Cap. Change with Temp.

KEMET

Designator Equivalent

EIA

Measured

without DC

Bias Voltage

Temp

Range, °C

CAPACITANCE TOLERANCE

Standard

M – 20ꢄ

K – 10ꢄ

J – 5ꢄ

Others

G

C0G

ꢀNP0ꢂ

-55 to

+125°

80

ppm/°C

H – 8ꢄ

G – 2ꢄ

F – 1ꢄ

D – .5pF

ꢀUltra Stableꢂ

R

-55° to

+125

XꢃR

15ꢄ

ꢀStableꢂ

WORKING VOLTAGE (DC)

2 – 200V; 1 – 100V; 5 – 50V

Standard tolerances for each Series

are shown in the repetitive parts lists.

Case Sizes

Radial

C052

C062

C512

C522

Axial

C11(

C12(

C192

C202

C222

Part Number Example: C052C102K2R5TA ꢀ1( digits – no spacesꢂ

AXIAL CAPACITOR MARKING

STANDARD C114C, C124C, C192C, C202C & C222C

KEMET, Temperature Characteristic

Capacitance, Capacitance Tolerance

Voltage

KC0G

101J

200V

0812

Date Code

RADIAL CAPACITOR MARKING

C052C & C062C STANDARD MARKING

BACK

FRONT

Voltage

KEMET

Style

100V

K

C062

X7R

Temperature Characteristic

0811

Date Code

Capacitance, Capacitance Tolerance

104K

C512 & C522 STANDARD MARKING

KEMET

SIZE and Temperature Characteristic

Capacitance, Capacitance Tolerance, Voltage

Date Code

C512X7R

105K 50V

0832

29

CERAMIC MOLDED/RADIAL – STANDARD

ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)

RATINGS & PART NUMBER REFERENCE

CAPACITANCE

pF

KEMET

PART NUMBER

CAPACITANCE

pF

KEMET

PART NUMBER

CAPACITANCE

pF

KEMET

PART NUMBER

200 VOLT – C114 STANDARD C0G

200 VOLT – C124 STANDARD C0G

200 VOLT – C202 STANDARD C0G

1.0

1.5

2.2

2.7

3.3

3.9

4.7

5.6

6.8

C114C109(1)2G5CA

C114C159(1)2G5CA

C114C229(1)2G5CA

C114C279(1)2G5CA

C114C339(1)2G5CA

C114C399(1)2G5CA

C114C479(1)2G5CA

C114C569(1)2G5CA

C114C689(1)2G5CA

C114C829(1)2G5CA

C114C100(2)2G5CA

C114C120(2)2G5CA

C114C150(2)2G5CA

C114C180(2)2G5CA

C114C220(2)2G5CA

C114C270(3)2G5CA

C114C330(3)2G5CA

C114C390(3)2G5CA

C114C470(3)2G5CA

C114C560(4)2G5CA

C114C680(4)2G5CA

C114C820(4)2G5CA

C114C101(4)2G5CA

C114C121(4)2G5CA

C114C151(4)2G5CA

C114C181(4)2G5CA

C114C221(4)2G5CA

C114C271(4)2G5CA

C114C331(4)2G5CA

390.0

470.0

560.0

C124C391(4)2G5CA

C124C471(4)2G5CA

C124C561(4)2G5CA

5,600.0

6,800.0

8,200.0

10,000.0

12,000.0

15,000.0

18,000.0

22000.0

C202C562(4)2G5CA

C202C682(4)2G5CA

C202C822(4)2G5CA

C202C103(4)2G5CA

C202C123(4)2G5CA

C202C153(4)2G5CA

C202C183(4)2G5CA

C202C223(4)2G5CA

100 VOLT – C124 STANDARD C0G

820.0

1,000.0

C124C821(4)1G5CA

C124C102(4)1G5CA

200 VOLT – C192 STANDARD C0G

680.0

820.0

C192C681(4)2G5CA

C192C821(4)2G5CA

C192C102(4)2G5CA

C192C122(4)2G5CA

C192C152(4)2G5CA

C192C182(4)2G5CA

C192C222(4)2G5CA

C192C272(4)2G5CA

C114C332(4)2G5CA

C114C392(4)2G5CA

C114C472(4)2G5CA

100 VOLT – C202 STANDARD C0G

8.2

10,000.0

12,000.0

15,000.0

18,000.0

22,000.0

27,000.0

33,000.0

C202C103(4)1G5CA

C202C123(4)1G5CA

C202C153(4)1G5CA

C202C183(4)1G5CA

C202C223(4)1G5CA

C202C273(4)1G5CA

C202C333(4)1G5CA

1,000.0

1,200.0

1,500.0

1,800.0

2,200.0

2,700.0

3,300.0

3,900.0

4,700.0

10.0

12.0

15.0

18.0

22.0

27.0

33.0

39.0

47.0

56.0

68.0

82.0

100.0

120.0

150.0

180.0

220.0

270.0

330.0

200 VOLT – C222 STANDARD C0G

27,000.0

33,000.0

39,000.0

47,000.0

C222C273(4)2G5CA

C222C333(4)2G5CA

C222C393(4)2G5CA

C222C473(4)2G5CA

100 VOLT – C192 STANDARD C0G

1,200.0

1,500.0

1,800.0

2,200.0

2,700.0

3,300.0

3,900.0

4,700.0

5,600.0

6,800.0

8,200.0

C192C122(4)1G5CA

C192C152(4)1G5CA

C192C182(4)1G5CA

C192C222(4)1G5CA

C192C272(4)1G5CA

C192C332(4)1G5CA

C192C392(4)1G5CA

C192C472(4)1G5CA

C192C562(4)1G5CA

C192C682(4)1G5CA

C192C822(4)1G5CA

100 VOLT – C222 STANDARD C0G

39,000.0

47,000.0

56,000.0

68,000.0

82,000.0

100,000.0

C222C393(4)1G5CA

C222C473(4)1G5CA

C222C563(4)1G5CA

C222C683(4)1G5CA

C222C823(4)1G5CA

C222C104(4)1G5CA

100 VOLT – C114 STANDARD C0G

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

82.0

100.0

120.0

150.0

180.0

220.0

270.0

330.0

390.0

470.0

560.0

680.0

C114C820(4)1G5CA

C114C101(4)1G5CA

C114C121(4)1G5CA

C114C151(4)1G5CA

C114C181(4)1G5CA

C114C221(4)1G5CA

C114C271(4)1G5CA

C114C331(4)1G5CA

C114C391(4)1G5CA

C114C471(4)1G5CA

C114C561(4)1G5CA

C114C681(4)1G5CA

(1) 1.0 pF to 8.2 pF: D— .5 pF

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(2) 10.0 pF to 22 pF: J— 5%, K— 10%

(3) 27.0 pF to 47 pF: G— 2%, J— 5%, K— 10%

(4) 56.0 pF and up: F— 1%,G— 2%, J— 5%, K— 10%

(1) 1.0 pF to 8.2 pF: D— .5 pF

(2) 10.0 pF to 22 pF: J— 5%, K— 10%

(3) 27.0 pF to 47 pF: G— 2%, J— 5%, K— 10%

(4) 56.0 pF and up: F— 1%,G— 2%, J— 5%, K— 10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— .5 pF

(2) 10.0 pF to 22 pF: J— 5%, K— 10%

(3) 27.0 pF to 47 pF: G— 2%, J— 5%, K— 10%

(4) 56.0 pF and up: F— 1%,G— 2%, J— 5%, K— 10%

30

CERAMIC MOLDED/RADIAL – STANDARD

ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)

RATINGS & PART NUMBER REFERENCE

CAPACITANCE

pF

KEMET

PART NUMBER

CAPACITANCE

pF

KEMET

PART NUMBER

200 VOLT – C062 SIZE C0G

200 VOLT – C052 SIZE C0G

3,300.0

3,900.0

4,700.0

5,600.0

6,800.0

8,200.0

10,000.0

C062C332(4)2G5CA

C062C392(4)2G5CA

C062C472(4)2G5CA

C062C562(4)2G5CA

C062C682(4)2G5CA

C062C822(4)2G5CA

C062C103(4)2G5CA

1.0

1.5

2.2

2.7

3.3

3.9

4.7

5.6

6.8

8.2

10.0

12.0

15.0

18.0

22.0

27.0

33.0

C052C109(1)2G5CA

C052C159(1)2G5CA

C052C229(1)2G5CA

C052C279(1)2G5CA

C052C339(1)2G5CA

C052C399(1)2G5CA

C052C479(1)2G5CA

C052C569(1)2G5CA

C052C689(1)2G5CA

C052C829(1)2G5CA

C052C100(2)2G5CA

C052C120(2)2G5CA

C052C150(2)2G5CA

C052C180(2)2G5CA

C052C220(2)2G5CA

C052C270(3)2G5CA

C052C330(3)2G5CA

C052C390(3)2G5CA

C052C470(3)2G5CA

C052C560(4)2G5CA

C052C680(4)2G5CA

C052C820(4)2G5CA

C052C101(4)2G5CA

C052C121(4)2G5CA

C052C151(4)2G5CA

C052C181(4)2G5CA

C052C221(4)2G5CA

C052C271(4)2G5CA

C052C331(4)2G5CA

C052C391(4)2G5CA

C052C471(4)2G5CA

C052C561(4)2G5CA

C052C681(4)2G5CA

C052C821(4)2G5CA

C052C102(4)2G5CA

C052C122(4)2G5CA

C052C152(4)2G5CA

C052C182(4)2G5CA

C052C222(4)2G5CA

C052C272(4)2G5CA

100 VOLT – C062 SIZE C0G

5,600.0

6,800.0

8,200.0

10,000.0

12,000.0

15,000.0

18,000.0

22,000.0

C062C562(4)1G5CA

C062C682(4)1G5CA

C062C822(4)1G5CA

C062C103(4)1G5CA

C062C123(4)1G5CA

C062C153(4)1G5CA

C062C183(4)1G5CA

C062C223(4)1G5CA

200 VOLT – C512 SIZE C0G

39.0

47.0

56.0

68.0

12,000.0

15,000.0

18,000.0

22,000.0

27,000.0

33,000.0

39,000.0

47,000.0

56,000.0

68,000.0

C512C123(4)2G5CA

C512C153(4)2G5CA

C512C183(4)2G5CA

C512C223(4)2G5CA

C512C273(4)2G5CA

C512C333(4)2G5CA

C512C393(4)2G5CA

C512C473(4)2G5CA

C512C563(4)2G5CA

C512C683(4)2G5CA

82.0

100.0

120.0

150.0

180.0

220.0

270.0

330.0

390.0

470.0

560.0

680.0

820.0

1,000.0

1,200.0

1,500.0

1,800.0

2,200.0

2,700.0

100 VOLT – C512 SIZE C0G

27,000.0

33,000.0

39,000.0

47,000.0

56,000.0

68,000.0

82,000.0

100,000.0

C512C273(4)1G5CA

C512C333(4)1G5CA

C512C393(4)1G5CA

C512C473(4)1G5CA

C512C563(4)1G5CA

C512C683(4)1G5CA

C512C823(4)1G5CA

C512C104(4)1G5CA

200 VOLT – C522 SIZE C0G

82,000.0

100,000.0

C522C823(4)2G5CA

C522C104(4)2G5CA

100 VOLT – C052 SIZE C0G

100 VOLT – C522 SIZE C0G

390.0

470.0

560.0

680.0

820.0

1,000.0

1,200.0

1,500.0

1,800.0

2,200.0

2,700.0

3,300.0

3,900.0

4,700.0

C052C391(4)1G5CA

120,000.0

150,000.0

180,000.0

C522C124(4)1G5CA

C522C154(4)1G5CA

C522C184(4)1G5CA

C052C471(4)1G5CA

C052C561(4)1G5CA

C052C681(4)1G5CA

C052C821(4)1G5CA

C052C102(4)1G5CA

C052C122(4)1G5CA

C052C152(4)1G5CA

C052C182(4)1G5CA

C052C222(4)1G5CA

C052C272(4)1G5CA

C052C332(4)1G5CA

C052C392(4)1G5CA

C052C472(4)1G5CA

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— .5 pF

(2) 10.0 pF to 22 pF: J— 5%, K— 10%

(3) 27.0 pF to 47 pF: G— 2%, J— 5%, K— 10%

(4) 56.0 pF and up: F— 1%,G— 2%, J— 5%, K— 10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— .5 pF

(2) 10.0 pF to 22 pF: J— 5%, K— 10%

(3) 27.0 pF to 47 pF: G— 2%, J— 5%, K— 10%

(4) 56.0 pF and up: F— 1%,G— 2%, J— 5%, K— 10%

31

CERAMIC MOLDED/RADIAL – STANDARD

STABLE TEMPERATURE CHARACTERISTIC—X7R

RATINGS & PART NUMBER REFERENCE

CAPACI-

TANCE

pF

CAPACI-

TANCE

pF

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

TOL.

%

KEMET

PART NUMBER

TOL.

%

KEMET

PART NUMBER

100 VOLT – C202 SIZE

100 VOLT – C124 SIZE

100 VOLT – C114 SIZE

C114C100K1R5CA

56,000

68,000

10

20

10

20

10

20

10

20

10

20

C202C563K1R5CA

5,600

6,800

8,200

10,000

10

20

10

20

C124C562K1R5CA

10

12

15

18

22

27

33

39

47

56

68

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

C202C683K1R5CA

C202C683M1R5CA

C202C823K1R5CA

C202C104K1R5CA

C202C104M1R5CA

C202C124K1R5CA

C202C154K1R5CA

C202C154M1R5CA

C202C184K1R5CA

C202C224K1R5CA

C202C224M1R5CA

C202C274K1R5CA

C202C334K1R5CA

C202C334M1R5CA

C124C682K1R5CA

C124C682M1R5CA

C124C822K1R5CA

C124C103K1R5CA

C124C103M1R5CA

C114C100M1R5CA

C114C120K1R5CA

C114C150K1R5CA

C114C150M1R5CA

C114C180K1R5CA

C114C220K1R5CA

C114C220M1R5CA

C114C270K1R5CA

C114C330K1R5CA

C114C330M1R5CA

C114C390K1R5CA

C114C470K1R5CA

C114C470M1R5CA

C114C560K1R5CA

C114C680K1R5CA

C114C680M1R5CA

C114C820K1R5CA

C114C101K1R5CA

C114C101M1R5CA

C114C121K1R5CA

C114C151K1R5CA

C114C151M1R5CA

C114C181K1R5CA

C114C221K1R5CA

C114C221M1R5CA

C114C271K1R5CA

C114C331K1R5CA

C114C331M1R5CA

C114C391K1R5CA

C114C471K1R5CA

C114C471M1R5CA

C114C561K1R5CA

C114C681K1R5CA

C114C681M1R5CA

C114C821K1R5CA

C114C102K1R5CA

C114C102M1R5CA

C114C122K1R5CA

C114C152K1R5CA

C114C152M1R5CA

C114C182K1R5CA

C114C222K1R5CA

C114C222M1R5CA

C114C272K1R5CA

C114C332K1R5CA

C114C332M1R5CA

C114C392K1R5CA

C114C472K1R5CA

C114C472M1R5CA

82,000

100,000

120,000

150,000

180,000

220,000

270,000

330,000

50 VOLT – C124 SIZE

12,000

15,000

18,000

22,000

27,000

33,000

39,000

47,000

10

20

10

20

10

20

10

20

C124C123K5R5CA

C124C153K5R5CA

C124C153M5R5CA

C124C183K5R5CA

C124C223K5R5CA

C124C223M5R5CA

C124C273K5R5CA

C124C333K5R5CA

C124C333M5R5CA

C124C393K5R5CA

C124C473K5R5CA

C124C473M5R5CA

50 VOLT – C202 SIZE

470,000

680,000

1,000,000

10

20

10

20

10

20

C202C474K5R5CA

82

C202C474M5R5CA

C202C684K5R5CA

C202C684M5R5CA

C202C105K5R5CA

C202C105M5R5CA

100

120

150

180

220

270

330

390

470

560

680

820

1,000

1,200

1,500

1,800

2,200

2,700

3,300

3,900

4,700

100 VOLT – C192 SIZE

12,000

15,000

18,000

22,000

27,000

33,000

39,000

47,000

56,000

68,000

82,000

100,000

10

20

10

20

10

20

10

20

10

20

10

20

C192C123K1R5CA

C192C153K1R5CA

C192C153M1R5CA

C192C183K1R5CA

C192C223K1R5CA

C192C223M1R5CA

C192C273K1R5CA

C192C333K1R5CA

C192C333M1R5CA

C192C393K1R5CA

C192C473K1R5CA

C192C473M1R5CA

C192C563K1R5CA

C192C683K1R5CA

C192C683M1R5CA

C192C823K1R5CA

C192C104K1R5CA

C192C104M1R5CA

100 VOLT – C222 SIZE

470,000

680,000

1,000,000

10

20

10

20

10

20

C222C474K1R5CA

C222C474M1R5CA

C222C684K1R5CA

C222C684M1R5CA

C222C105K1R5CA

C222C105M1R5CA

50 VOLT – C222 SIZE

2,200,000

3,300,000

10

20

10

20

C222C225K5R5CA

C222C225M5R5CA

C222C335K5R5CA

C222C335M5R5CA

50 VOLT – C192 SIZE

56,000

68,000

10

20

10

20

10

20

10

20

10

C192C563K5R5CA

C192C683K5R5CA

C192C683M5R5CA

C192C823K5R5CA

C192C104K5R5CA

C192C104M5R5CA

C192C124K5R5CA

C192C154K5R5CA

C192C154M5R5CA

C192C184K5R5CA

C192C224K5R5CA

C192C224M5R5CA

C192C274K5R5CA

82,000

100,000

120,000

150,000

180,000

220,000

270,000

50 VOLT – C114 SIZE

5,600

6,800

8,200

10,000

10

20

10

20

C114C562K5R5CA

C114C682K5R5CA

C114C682M5R5CA

C114C822K5R5CA

C114C103K5R5CA

C114C103M5R5CA

32

CERAMIC MOLDED/RADIAL – STANDARD

STABLE TEMPERATURE CHARACTERISTIC—X7R

RATINGS & PART NUMBER REFERENCE

CAPACI-

TANCE

pF

CAPACI-

TANCE

pF

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

TOL.

%

KEMET

PART NUMBER

TOL.

%

KEMET

PART NUMBER

200 VOLT – C052 SIZE

C052C100K2R5CA

100 VOLT – C062 SIZE

100 VOLT – C052 SIZE

C052C122K1R5CA

10

12

15

18

22

27

33

39

47

56

68

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

10

20

1,200

1,500

1,800

2,200

2,700

3,300

3,900

4,700

5,600

6,800

8,200

10,000

10

20

10

20

10

20

10

20

10

20

10

20

12,000

15,000

18,000

22,000

27,000

33,000

39,000

47,000

56,000

68,000

82,000

100,000

1,000,000

10

20

10

20

10

20

10

20

10

20

10

20

10

20

C062C123K1R5CA

C052C100M2R5CA

C052C120K2R5CA

C052C150K2R5CA

C052C150M2R5CA

C052C180K2R5CA

C052C220K2R5CA

C052C220M2R5CA

C052C270K2R5CA

C052C330K2R5CA

C052C330M2R5CA

C052C390K2R5CA

C052C470K2R5CA

C052C470M2R5CA

C052C560K2R5CA

C052C680K2R5CA

C052C680M2R5CA

C052C820K2R5CA

C052C101K2R5CA

C052C101M2R5CA

C052C121K2R5CA

C052C151K2R5CA

C052C151M2R5CA

C052C181K2R5CA

C052C221K2R5CA

C052C221M2R5CA

C052C271K2R5CA

C052C331K2R5CA

C052C331M2R5CA

C052C391K2R5CA

C052C471K2R5CA

C052C471M2R5CA

C052C561K2R5CA

C052C681K2R5CA

C052C681M2R5CA

C052C821K2R5CA

C052C102K2R5CA

C052C102M2R5CA

C062C153K1R5CA

C062C153M1R5CA

C062C183K1R5CA

C062C223K1R5CA

C062C223M1R5CA

C062C273K1R5CA

C062C333K1R5CA

C062C333M1R5CA

C062C393K1R5CA

C062C473K1R5CA

C062C473M1R5CA

C062C563K1R5CA

C062C683K1R5CA

C062C683M1R5CA

C062C823K1R5CA

C062C104K1R5CA

C062C104M1R5CA

C062C105K1R5CA

C062C105M1R5CA

C052C152K1R5CA

C052C152M1R5CA

C052C182K1R5CA

C052C222K1R5CA

C052C222M1R5CA

C052C272K1R5CA

C052C332K1R5CA

C052C332M1R5CA

C052C392K1R5CA

C052C472K1R5CA

C052C472M1R5CA

C052C562K1R5CA

C052C682K1R5CA

C052C682M1R5CA

C052C822K1R5CA

C052C103K1R5CA

C052C103M1R5CA

82

100

120

150

180

220

270

330

390

470

560

680

820

1,000

50 VOLT – C052 SIZE

C052C123K5R5CA

12,000

15,000

18,000

22,000

27,000

33,000

39,000

47,000

56,000

68,000

82,000

100,000

10

20

10

20

10

20

10

20

10

20

10

20

50 VOLT – C062 SIZE

C052C153K5R5CA

C052C153M5R5CA

C052C183K5R5CA

C052C223K5R5CA

C052C223M5R5CA

C052C273K5R5CA

C052C333K5R5CA

C052C333M5R5CA

C052C393K5R5CA

C052C473K5R5CA

C052C473M5R5CA

C052C563K5R5CA

C052C683K5R5CA

C052C683M5R5CA

C052C823K5R5CA

C052C104K5R5CA

C052C104M5R5CA

120,000

150,000

180,000

220,000

270,000

330,000

390,000

470,000

560,000

680,000

820,000

1,000,000

10

20

10

20

10

20

10

20

10

20

10

20

C062C124K5R5CA

C062C154K5R5CA

C062C154M5R5CA

C062C184K5R5CA

C062C224K5R5CA

C062C224M5R5CA

C062C274K5R5CA

C062C334K5R5CA

C062C334M5R5CA

C062C394K5R5CA

C062C474K5R5CA

C062C474M5R5CA

C062C564K5R5CA

C062C684K5R5CA

C062C684M5R5CA

C062C824K5R5CA

C062C105K5R5CA

C062C105M5R5CA

200 VOLT – C062 SIZE

C062C122K2R5CA

1,200

1,500

1,800

2,200

2,700

3,300

3,900

4,700

5,600

6,800

8,200

10,000

10

20

10

20

10

20

10

20

10

20

10

20

50 VOLT – C512 SIZE

C062C152K2R5CA

C062C152M2R5CA

C062C182K2R5CA

C062C222K2R5CA

C062C222M2R5CA

C062C272K2R5CA

C062C332K2R5CA

C062C332M2R5CA

C062C392K2R5CA

C062C472K2R5CA

C062C472M2R5CA

C062C562K2R5CA

C062C682K2R5CA

C062C682M2R5CA

C062C822K2R5CA

C062C103K2R5CA

C062C103M2R5CA

1,000,000

1,500,000

2,000,000

2,200,000

10

20

10

20

10

20

10

20

C512C105K5X5CA

C512C105M5X5CA

C512C155K5X5CA

C512C155M5X5CA

C512C205K5X5CA

C512C205M5X5CA

C512C225K5X5CA

C512C225M5X5CA

100 VOLT – C522 SIZE

1,000,000

10

20

C522C105K1X5CA

C522C105M1X5CA

50 VOLT – C522 SIZE

2,700,000

3,300,000

10

20

10

20

C522C275K5X5CA

C522C275M5X5CA

C522C335K5X5CA

C522C335M5X5CA

33

CERAMIC LEADED

PACKAGING INFORMATION

Ceramic Axial

Lead Tape and Reel Packaging

KEMET offers standard reeling of Molded and Conformally

Coated Axial Leaded Ceramic Capacitors for automatic insertion

or lead forming machines per EIA specification RS-296. KEMET’s

internal specification four-digit suffix, 7200, is placed at the end of

the part number to designate tape and reel packaging, ie:

C410C104Z5U5CA7200.

Paper (50 lb.) test minimum is inserted between the layers of

capacitors wound on reels for component pitch ≤ 0.400”.

Capacitor lead length may extend only a maximum of .0625”

(1.59mm) beyond the tapes’ edges. Capacitors are centered in a

row between the two tapes and will deviate only

0.031

(0.79mm) from the row center. A minimum of 36” (91.5 cm) leader

tape is provided at each end of the reel capacitors. Universal

splicing clips are used to connect the tape. Standard reel

quantities are shown on page 48.

46

CERAMIC LEADED

PACKAGING INFORMATION

47

CERAMIC LEADED

PACKAGING INFORMATION

CERAMIC PACKAGING

Standard (1)

Bulk

Quantity

Ammo Pack

Maximum

Reel

Quantity

KEMET

Series

Military

Style

Military

Specification

Reel

Size

Quantity

Maximum

C114C-K-G

C124C-K-G

C192C-K-G

C202C-K

C222C-K

C052C-K-G

C062C-K-G

C114G

C124G

C192G

C202G

C222G

C052/56G

C062/66G

C512G

C522G

C114T

C124T

C192T

C202T

C222T

C052/56T

C062/66T

C31X

C32X

C33X

C340

C350

C410

C412

C420

C430

C440

C512

C522

C617

CK12, CC75

CK13, CC76

CK14, CC77

CK15

MIL-C-11015/

MIL-PRF-20

200/Box

100/Box

25/Box

5000

3000

500

12"

N/A

12"

CK16

10/Tray

300

CK05, CC05

CK06, CC06

CCR75

CCR76

CCR77

CC78-CCR78

CC79-CCR79

CCR05

100/Bag

200/Box

100/Box

25/Box

2000

1500

2000

1500

5000

3000

500

MIL-PRF-20

10/Tray

300

100/Bag

Footnote (2)

200/Box

100/Box

25/Box

1700

1500

N/A

CCR06

CC07-CCR07

CC08-CCR08

CKR11

CKR12

CKR14

CKR15

CKR16

CKR05

CKR06

N/A

MIL-PRF-39014

5000

3000

500

10/Tray

300

100/Bag

500/Bag

250/Bag

100/Bag

50/Bag

300/Box

200/Box

300/Box

200/Box

Footnote (2)

250/Bag

100/Bag

50/Bag

1700

1500

2500

1500

1000

500

5000

2500

N/A

1000

500

2500

1500

1000

N/A

4000

2000

12"

N/A

12"

N/A

C622/C623

C627/C628

C630/C631

C637/C638

C640/C641

C642/C643

C647/C648

C657/C658

C667/C668

50/Bag

500

50/Bag

NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.

(2) Quantity varies. For further details, please consult the factory.

48


型号：	C052C182F2G5TA7200
厂家：	KEMET CORPORATION
描述：	Ceramic Capacitor, Multilayer, Ceramic, 200V, 1% +Tol, 1% -Tol, C0G, 30ppm/Cel TC, 0.0018uF, Through Hole Mount, RADIAL LEADED 电容器
文件：	总16页 (文件大小：1413K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

C052C182F2G5TA7200 [KEMET]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E