LTL-4233-032A [LITEON]
Property of Lite-On Only; 精简版，关于财产只有
| 型号： | LTL-4233-032A |
| 厂家： | 
LITE-ON TECHNOLOGY CORPORATION |
| 描述： | Property of Lite-On Only |
| 文件： | 总8页 (文件大小：533K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Features
* High Intensity.
* Popular T-1 3/4 diameter Package.
* Selected minimun intensities.
* General purpose leads.
* Reliable and rugged.
Package Dimensions
Part No.
Lens
Source Color
Green
LTL-4233-032A
Green Diffused
Notes:
1. All dimensions are in millimeters (inches).
±
2. Tolerance is 0.25mm(.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
1
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
℃
Absolute Maximum Ratings at T =25
A
Parameter
Maximum Rating
100
Unit
mW
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
120
mA
mA
Continuous Forward Current
30
0.4
5
℃
℃
Derating Linear From 50
mA/
Reverse Voltage
V
℃
-55 to + 100
℃
℃
Operating Temperature Range
Storage Temperature Range
℃
-55 to + 100
Lead Soldering Temperature
[1.6mm(.063") From Body]
℃
260 for 5 Seconds
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
2
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
℃
Electrical / Optical Characteristics at T =25
A
Parameter
Luminous Intensity
Viewing Angle
Symbol
IV
Min.
5.6
Typ.
19
Max.
Unit
mcd
deg
nm
nm
nm
V
Test Condition
IF = 10mA
Note 1,4
θ
2
1/2
36
Note 2 (Fig.6)
Measurement
@Peak (Fig.1)
λ
P
Peak Emission Wavelength
Dominant Wavelength
Spectral Line Half-Width
Forward Voltage
565
569
30
λd
Δλ
VF
Note 3
2.1
2.6
IF = 20mA
μ
A
Reverse Current
IR
100
VR = 5V
Capacitance
C
35
pF
VF = 0 , f = 1MHz
Note: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
(Commission International De L'Eclairage) eye-response curve.
θ
2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
λd is derived from the CIE chromaticity diagram and represents the single
3. The dominant wavelength,
wavelength which defines the color of the device.
±
4. The Iv guarantee should be added 15%.
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
3
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Typical Electrical / Optical Characteristics Curves
℃
(25
Ambient Temperature Unless Otherwise Noted)
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
4
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 5mm (0.197") formed lead spacing available.
* Folding packaging simplifies handling and testing.
Package Dimensions
Specification
Minimum Maximum
Item
Symbol
mm
3.8
inch
0.149
0.091
--
mm
4.2
inch
0.165
0.118
0.078
0.827
1.177
0.433
0.511
0.228
0.301
0.035
0.384
0.610
0.118
0.748
Tape Feed Hole Diameter
Component Lead Pitch
Front to Rear Deflection
D
F
2.3
3.0
△
H
--
2.0
Feed Hole to Bottom of Component
Feed Hole to Overall Component Height
Lead Length After Component Height
Feed Hole Pitch
H1
H2
L
20.0
28.3
0.787
1.114
W0
21.0
29.9
11.0
13.0
5.8
7.65
0.90
9.75
15.5
3.0
P
12.4
4.4
5.05
--
8.5
14.5
0
0.488
0.173
0.198
--
0.334
0.571
0
Lead Location
P1
P2
T
W0
W1
W2
W3
Center of Component Location
Total Tape Thickness
Feed Hole Location
Adhesive Tape Width
Adhesive Tape Position
Tape Width
17.5
0.689
19.0
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
5
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household applications).Consult Liteon’s Sales in advance for information on
applications in which exceptional reliability is required, particularly when the failure or malfunction of the
LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment,
medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
4. Lead Forming & Assembly
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the lead frame as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point.
Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering conditions :
Soldering iron
Wave soldering
100°C Max.
Temperature
Soldering time
300°C Max.
Pre-heat
3 sec. Max.
Pre-heat time
Solder wave
Soldering time
60 sec. Max.
260°C Max.
10 sec. Max.
(one time only)
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
catastrophic failure of the LED
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
6
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
6. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be
incorporated in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
7
of
8
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
7. Reliability Test
Classification
Test Item
Test Condition
Reference Standard
Ta= Under Room Temperature As
Per Data Sheet Maximum Rating
MIL-STD-750D:1026 (1995)
MIL-STD-883D:1005 (1991)
Operation Life
*Test Time= 1000HRS (-24HRS,+72HRS) JIS C 7021:B-1 (1982)
Ta= 65±5℃
RH= 90 〜95%
Test Time= 240HRS±2HRS
High Temperature
High Humidity
Storage
MIL-STD-202F: 103B(1980)
JIS C 7021 : B-11(1982)
Ta= 65±5℃
High Temperature
High Humidity
Reverse BIAS
Endurance
Test
RH= 90 〜95%
JIS C 7021 : B-11(1982)
VR=5V
Test Time = 500HRS (-24HRS, +48HRS)
High Temperature
Storage
Ta= 105±5℃
MIL-STD-883D:1008 (1991)
*Test Time= 1000HRS (-24HRS,+72HRS) JIS C 7021:B-10 (1982)
Ta= -55±5℃
*Test Time=1000HRS (-24HRS,+72HRS)
Low Temperature
Storage
JIS C 7021:B-12 (1982)
MIL-STD-202F:107D (1980)
105℃ 〜25℃ 〜-55℃ 〜25℃
Temperature
Cycling
MIL-STD-750D:1051(1995)
30mins 5mins
10 Cycles
30mins 5mins
MIL-STD-883D:1010 (1991)
JIS C 7021: A-4(1982)
105 ± 5℃ 〜-55℃ ± 5℃
MIL-STD-202F:107D(1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1011 (1991)
Thermal
Shock
10mins
10mins
10 Cycles
Environmental
Test
MIL-STD-202F:210A(1980)
MIL-STD-750D:2031(1995)
JIS C 7021: A-1(1982)
Solder
Resistance
T.sol = 260 ± 5℃
Dwell Time= 10 ± 1secs
MIL-STD-202F:208D(1980)
MIL-STD-750D:2026(1995)
MIL-STD-883D:2003(1991)
JIS C 7021: A-2(1982)
T. sol = 230 ± 5℃
Dwell Time= 5 ± 1secs
Solderability
8. Others
The appearance and specifications of the product may be modified for improvement, without prior notice.
Part No. : LTL-4233-032A
BNS-OD-C131/A4
Page :
8
of
8
相关型号：
©2020 ICPDF网 联系我们和版权申明