B1161UC4LXX [LITTELFUSE]
Dual port protection is provided by a programmable device that is referenced; 双端口保护由所引用的可编程器件提供
| 型号： | B1161UC4LXX |
| 厂家： | 
LITTELFUSE |
| 描述： | Dual port protection is provided by a programmable device that is referenced |
| 文件： | 总4页 (文件大小：135K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SIDACtor® ProtectionThyristors
SLIC Protection
Battrax® Series - Dual Port Negative - MS-013
Description
The Dual Port Negative Battrax® Series are programmable
SIDACtor® devices designed to protect SLICs (Subscriber
Line Interface Circuit) from damaging overvoltage transients.
Dual port protection is provided by a programmable device
that is referenced to a negative voltage souce while internal
diodes provide protection from positive surge events.
Features and Benefits
tꢀ Low voltage overshoot
tꢀ Low on-state voltage
tꢀ Dual-port protection
tꢀ Gate trigger tracking
device
tꢀ Does not degrade with
Agency Approvals
tꢀ Integrated diode for
use
positive voltage surges
tꢀ Fails short circuit when
surged in excess of
ratings
Agency
Agency File Number
E133083
Applicable Global Standards
Pinout Designation
tꢀ TIA-968-A
tꢀ TIA-968-B
tꢀ GR 1089 Intra-building
tꢀ IEC 61000-4-5
tꢀ YD/T 1082
1
2
6
5
tꢀ ITU K.20/21 Enhanced
Level
tꢀ YD/T 993
3
4
tꢀ ITU K.20/21 Basic Level
tꢀ GR 1089 Inter-building
tꢀ YD/T 950
Schematic Symbol
6 (T2)
(T1) 1
5 Ground
(-V
REF
) 2
4 (R2)
(R1) 3
Electrical Characteristics
VDRM
@lDRM=5μA
VS
VT
IH
IS
IT
VF
Capacitance*
@100V/μs
@IT=2.2 Amps
Part Number
Marking
V min
V max
mA min mA max A max
V max
V max pF min pF max
B1101UC4Lxx
B1101UC4
I-VREF*ꢀꢁꢀ*ꢂꢃꢄꢅ7* I-VREF*ꢀꢁꢀ*ꢂꢃꢆ7*
100
160
200
100
100
100
2.2
2.2
2.2
4
4
4
5
5
5
30
30
30
200
200
200
B1161UC4Lxx B1161UC4 I-VREF*ꢀꢁꢀ*ꢂꢃꢄꢅ7* I-VREF*ꢀꢁꢀ*ꢂꢃꢆ7*
B1201UC4Lxx B1201UC4 I-VREF*ꢀꢁꢀ*ꢂꢃꢄꢅ7* I-VREF*ꢀꢁꢀ*ꢂꢃꢆ7*
Notes:
- VREF Max Value for the negative Battrax is -200 V.
- XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack).
- Absolute maximum ratings measured atTA= 25ºC (unless otherwise noted).
- Devices are uni-directional
- All electrical characteristics shown are defined fromTip (pin 1 & 6) to Ground (pin 5) and
Ring (pin 3 & 4) to Ground (pin 5)
* Off-state capacitance (CO) is measured across pins 1 & 5, 3 & 5, 4 & 5, and 6 & 5
at 1 MHz with a 2V bias.
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
126
Revised: February 22, 2011
SIDACtor® ProtectionThyristors
SLIC Protection
Surge Ratings
IPP
ITSM
0.2x310 1
2x10 1
2x10 2
8x20 1
10x160 1
10x160 2
10x560 1
10x560 2
5x320 1
10x360 1
10x360 2
10x1000 1
10x1000 2
5x310 1
di/dt
0.5x700 2
1.2x50 2
9x720 2
10x700 2
50/60 Hz
A min
A min
A min
A min
A min
A min
A min
A min
A min
A min A/μs max
50 500
C
Notes:
50
500
400
200
150
200
175
100
200
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product.
- IPPꢀSBUJOHTꢀBQQMJDBCMFꢀPWFSꢀUFNQFSBUVSFꢀSBOHFꢀPGꢀꢂꢇꢆ$ꢀUPꢀꢁꢊꢈ$ꢀꢀꢋ*PP rating assumes VREFꢀFRVBMTꢀꢁꢌꢂꢀꢇꢊꢀ7ꢍ
- The device must initially be in thermal equilibrium with -40°C < TJ <ꢀꢁꢃꢈꢆ¡$
1 Current waveform in μs
2 Voltage waveform in μs
Thermal Considerations
Package
Symbol
Parameter
Value
Unit
Modified MS-013
TJ
Operating JunctionTemperature Range
ꢂꢇꢆꢀUPꢀꢁꢃꢅꢈ
°C
6
5
4
TS
StorageTemperature Range
ꢂꢉꢈꢀUPꢀꢁꢃꢈꢆ
°C
1
2
3
R0JA
Thermal Resistance: Junction to Ambient
60
°C/W
V-I Characteristics
tr x td PulseWaveform
+I
tr = rise time to peak value
td = decay time to half value
V
Peak
Value
100
VREF
Waveform = tr x td
IF
VDRM
VS
VT
-V
+V
50
0
Half Value
IDRM
IH
IS
IT
tr
td
PIN 5 CONNECTEDTO GROUND
0
t – Time (μs)
PIN 2 CONNECTEDTO V
IPP
REF
-I
NormalizedVS Change vs. JunctionTemperature
Normalized DC Holding Current vs. CaseTemperature
2.0
1.8
1.6
1.4
14
12
10
8
6
25°C
25 °C
1.2
4
1.0
0.8
0.6
0.4
2
0
-4
-6
-8
-40 -20
0
20 40 60
80 100 120 140 160
-40 -20
0
20 40 60 80 100 120 140 160
CaseTemperature (TC) - ºC
JunctionTemperature (TJ) – °C
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
127
Please refer to www.littelfuse.com for current information.
Revised: February 22, 2011
SIDACtor® ProtectionThyristors
SLIC Protection
Soldering Parameters
Pb-Free assembly
(see Fig. 1)
Reflow Condition
Figure 1
tP
-Temperature Min (Ts(min)
)
ꢁꢃꢈꢆ¡$
ꢁꢅꢆꢆ¡$
TP
Critical Zone
L toTP
Ramp-up
-Temperature Max (Ts(max)
)
T
Pre Heat
-Time (Min to Max) (ts)
60-180 secs.
TL
tL
Average ramp up rate (LiquidusTemp (TL)
to peak)
TS(max)
3°C/sec. Max.
Ramp-down
TS(max) toTL - Ramp-up Rate
3°C/sec. Max.
ꢁꢅꢃꢐ¡$
Preheat
-Temperature (TL) (Liquidus)
TS(min)
Reflow
tS
-Temperature (tL)
60-150 secs.
ꢁꢅꢉꢆꢋꢁꢆꢌꢂꢈꢍ¡$
PeakTemp (TP)
25
time to peak temperature
(t 25ºC to peak)
Time within 5°C of actual PeakTemp (tp)
30 secs. Max.
Time
Ramp-down Rate
6°C/sec. Max.
8 min. Max.
ꢁꢅꢉꢆ¡$
Time 25°C to PeakTemp (TP)
Do not exceed
Physical Specifications
Environmental Specifications
80% Rated VDRM (VDC Peakꢍꢀꢁꢃꢅꢈ¡$ꢀPSꢀꢁꢃꢈꢆ¡$ꢎꢀ
504 or 1008 hrs. MIL-STD-750 (Method 1040)
JEDEC, JESD22-A-101
HighTempVoltage
Blocking
Lead Material
Terminal Finish
Body Material
Copper Alloy
100% Matte-Tin Plated
ꢂꢉꢈ¡$ꢀUPꢀꢁꢃꢈꢆ¡$ꢎꢀꢃꢈꢀNJOꢄꢀEXFMMꢎꢀꢃꢆꢀVQꢀUPꢀꢃꢆꢆꢀ
cycles. MIL-STD-750 (Method 1051) EIA/JEDEC,
JESD22-A104
Temp Cycling
UL recognized epoxy meeting flammability
classification 94V-0
52 VDCꢀꢋꢁꢊꢈ¡$ꢍꢀꢊꢈꢏ3)ꢎꢀꢈꢆꢇꢀVQꢀUPꢀꢃꢆꢆꢊꢀISTꢄꢀꢀ&*"ꢌ
JEDEC, JESD22-A-101
BiasedTemp &
Humidity
ꢁꢃꢈꢆ¡$ꢀꢃꢆꢆꢊꢀISTꢄꢀꢀ.* ꢂ45%ꢂꢐꢈꢆꢀꢋ.FUIPEꢀꢃꢆꢑꢃꢍꢀ
JEDEC, JESD22-A-101
HighTemp Storage
LowTemp Storage
-65°C, 1008 hrs.
ꢆ¡$ꢀUPꢀꢁꢃꢆꢆ¡$ꢎꢀꢈꢀNJOꢄꢀEXFMMꢎꢀꢃꢆꢀTFDꢄꢀUSBOTGFSꢎꢀ
10 cycles. MIL-STD-750 (Method 1056) JEDEC,
JESD22-A-106
Thermal Shock
Autoclave (Pressure
CookerTest)
ꢁꢃꢅꢃ¡$ꢎꢀꢃꢆꢆꢏ3)ꢎꢀꢅBUNꢎꢀꢅꢇꢀVQꢀUPꢀꢃꢉꢊꢀISTꢄꢀꢀ&*"ꢌ
JEDEC, JESD22-A-102
Resistance to Solder
Heat
ꢁꢅꢉꢆ¡$ꢎꢀꢑꢆꢀTFDTꢄꢀꢀ.* ꢂ45%ꢂꢐꢈꢆꢀꢋ.FUIPEꢀꢅꢆꢑꢃꢍ
Moisture Sensitivity
Level
ꢊꢈꢏ3)ꢎꢀꢁꢊꢈ¡$ꢎꢀꢃꢉꢊꢀISTꢄꢎꢀꢑꢀSFnPXꢀDZDMFTꢀ
ꢋꢁꢅꢉꢆ¡$ꢀ1FBLꢍꢄꢀꢀ+&%&$ꢂ+ꢂ45%ꢂꢆꢅꢆꢎꢀ-FWFMꢀꢃ
Part Numbering
Part Marking
B1xx 1 U C 4 L xx
PACKING OPTIONS
TYPE
RP: Reel Pack
Part Marking Code
B1: Negative Battrax SIDACtor
(Refer to Electrical CharacteristicsTable)
TP:Tube Pack
XXXXXXXX
XXXXX
RoHS COMPLIANT
DUAL PORT
HOLDING CURRENT
Date Code
10: 100 mA
20: 200 mA
16: 160 mA
I
PP RATING
CONSTRUCTION VARIABLE
PACKAGETYPE
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
128
Revised: February 22, 2011
SIDACtor® ProtectionThyristors
SLIC Protection
Dimensions — MS-013
Inches
Millimeters
Dimensions
Min
Max
Min
Max
0.065
(1.65)
Pad Outline
A
B
C
D
E
F
G
H
J
0.360
0.352
0.400
0.043
0.047
0.293
0.289
0.089
0.041
0.020
0.133
0.364
0.356
0.412
0.045
0.055
0.297
0.293
0.093
0.049
---
9.14
8.94
10.16
1.09
1.19
7.44
9.25
9.04
10.46
1.13
1.40
7.54
7.44
2.36
1.24
---
C
0.460
(11.68)
0.138
(3.50)
Dimension are in inches
(and millimeters).
0.059
(1.50)
E
D
7ºTYP
J
7ºTYP
A
G
F
Burr Side
H
7.34
96º
A
2.26
1.04
0.51
3.38
Mold Split
Line
4º
A
Detail A
MIN Length
of Flat
7ºTYP
K
BSC*
K
BSC*
7ºTYP
B
0.143
3.63
* BSC = Basic Spacing between Centers
Packing Options
Industry Standard
PackageType
Description
Quantity
Added Suffix
Modified MS-013 6-pin
Tape and Reel Pack
1500
RP
EIA-481-D
U
Modified MS-013 6-pin
Tube Pack
500
(50 per tube)
TP
N/A
Tape and Reel Specification — MS-013
.157
(4.0)
.630
(16.0)
.472
(12.0)
12.99
(330)
.512 (13.0) Arbor
Hole Dia.
Dimensions are in inches
(and millimeters)
0.700
(17.8)
Direction of Feed
Tube Pack Specification — MS-013
Message Location
.020 .005
WALL TYP.
.045
(1.14)
(0.51 0.13)
20.000 .030
(508.00 0.76)
.310
(7.87)
.108
(2.74)
90˚
.005 A
.110
(2.79)
6
.165
(4.19)
Interior of the Tube
A
.225
(5.72)
.150
(3.81)
Dimensions are in inches
(and millimeters)
.525
(13.34)
© 2011 Littelfuse, Inc.
129
Revised: February 22, 2011
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
相关型号：
©2020 ICPDF网 联系我们和版权申明