LTC1257CS8#PBF [Linear]
LTC1257 - Complete Single Supply 12-Bit Voltage Output DAC in SO-8; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C;型号: | LTC1257CS8#PBF |
厂家: | Linear |
描述: | LTC1257 - Complete Single Supply 12-Bit Voltage Output DAC in SO-8; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C 转换器 光电二极管 |
文件: | 总12页 (文件大小:142K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC1257
Complete Single Supply
12-Bit Voltage Output
DAC in SO-8
U
FEATURES
DESCRIPTIO
The LTC®1257 is a complete single supply, 12-bit voltage
output D/A converter (DAC) in an SO-8 package. The
LTC1257 includes an output buffer amplifier, 2.048V
voltagereferenceandaneasytousethree-wirecascadable
serial interface. An external reference can be used to
override the internal reference and extend the output
voltage range to 12V. The power supply current is a low
350µA when operating from a 5V supply, making the
LTC1257idealforbattery-poweredapplications.Thespace-
saving 8-pin SO package and operation with no external
components provide the smallest 12-bit D/A system
available.
■
8-Pin SO Package
■
Buffered Voltage Output
■
Built-In 2.048V Reference
■
500µV/LSB with 2.048V Full Scale
■
1/2LSB Max DNL Error
■
Guaranteed 12-Bit Monotonic
■
3-Wire Cascadable Serial Interface
■
Wide Single Supply Range: VCC = 4.75V to 15.75V
■
Low Power: ICC Typ = 350µA with 5V Supply
U
APPLICATIO S
, LTC and LT are registered trademarks of Linear Technology Corporation.
■
Digital Offset/Gain Adjustment
■
Industrial Process Control
■
Automatic Test Equipment
U
TYPICAL APPLICATIO
Daisy-Chained Control Outputs
Differential Nonlinearity
vs Input Code
5V
0.5
0.0
0.1µF
V
D
IN
CC
CLK
LTC1257
µP
V
CONTROL OUTPUT 1
OUT
LOAD
D
V
REF
GND
OUT
0.1µF
V
CC
D
IN
CLK
LTC1257
V
OUT
CONTROL OUTPUT 2
LOAD
V
REF
D
GND
OUT
–0.5
0
512 1024 1536 2048 2560 3072 3584 4098
CODE
TO NEXT DAC
1257 TA01
1257 TA05
1
LTC1257
W W
U W
U W
U
ABSOLUTE AXI U RATI GS
PACKAGE/ORDER I FOR ATIO
(Note 1)
TOP VIEW
VCC to GND ............................................ –0.5V to 16.5V
TTL Input Voltage .......................... –0.5V to VCC + 0.5V
VOUT .............................................. –0.5V to VCC + 0.5V
REF ................................................ –0.5V to VCC + 0.5V
Operating Temperature Range
ORDER PART
V
V
NUMBER
CLK
1
2
3
4
8
7
6
5
CC
D
OUT
IN
LTC1257CN8
LTC1257IN8
REF
LOAD
GND
D
OUT
LTC1257C ............................................. 0°C to 70°C
LTC1257I ........................................ –40°C to 85°C
Maximum Junction Temperature
Plastic Package ............................. –65°C to 125°C
Storage Temperature Range ................ –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................. 300°C
N8 PACKAGE
8-LEAD PDIP
TJMAX = 125°C, θJA = 100°C/W
TOP VIEW
LTC1257CS8
LTC1257IS8
CLK
1
2
3
4
8
7
6
5
V
V
CC
D
IN
OUT
LOAD
REF
S8 PART MARKING
D
GND
OUT
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 125°C, θJA = 150°C/W
1257
1257I
Consult LTC Marketing for parts specified with wider operating temperature
ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at
TA = TMIN to TMAX. VCC = 4.75V to 15.75V, internal or external reference (2.475V ≤ VREF ≤ VCC – 2.7V), unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DAC
Resolution
●
●
12
Bits
LSB
DNL
INL
Differential Nonlinearity
Guaranteed Monotonic (Note 4)
±0.5
Integral Nonlinearity
LTC1257C (Note 4)
LTC1257I (Note 4)
●
●
±3.5
±4.0
LSB
LSB
OFF
Offset Error
When Using Internal Reference, LTC1257C
When Using Internal Reference, LTC1257I
●
●
±8
±10
LSB
LSB
When Using External Reference, LTC1257C
When Using External Reference, LTC1257I
●
●
±4
±5
mV
mV
OFF
Offset Error Tempco
When Using Internal Reference (Note 2)
When Using External Reference (Note 2)
●
●
±0.02
±15
±0.066
±30
LSB/°C
µV/°C
TC
Gain Error
●
●
0.5
±2
LSB
Gain Error Tempco
(Note 2)
± 0.01
±0.02
LSB/°C
Reference
Reference Output Voltage
I
I
= 0, LTC1257C
= 0, LTC1257I
●
●
2.028
2.018
2.048
2.068
2.078
V
V
REF
REF
Reference Output Tempco
Reference Line Regulation
I
= 0
●
±0.06
LSB/°C
REF
I
I
= 0, LTC1257C
= 0, LTC1257I
●
●
±0.4
±0.7
LSB/V
LSB/V
REF
REF
Reference Load Regulation
Reference Input Range
0 ≤ I ≤ 100µA
●
●
●
±1
12
18
LSB
V
REF
V
> V
+ 2.7V
REF
2.475
8
CC
Reference Input Resistance
Reference Input Capacitance
Short-Circuit Current
14
15
kΩ
pF
(Note 2)
Shorted to GND
V
●
90
mA
REF
2
LTC1257
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at
TA = TMIN to TMAX. VCC = 4.75V to 15.75V, internal or external reference (2.475V ≤ VREF ≤ VCC – 2.7V), unless otherwise noted.
SYMBOL PARAMETER
Power Supply
CONDITIONS
MIN
TYP
MAX
UNITS
V
Positive Supply Voltage
Supply Current
For Specified Performance
●
4.75
15.75
V
CC
I
4.75V ≤ V ≤ 5.25V
●
●
350
800
600
1500
µA
µA
CC
CC
4.75V ≤ V ≤ 15.75V
CC
Op Amp DC Performance
Short-Circuit Current Low
V
V
Shorted to GND
●
●
●
60
60
mA
mA
Ω
OUT
OUT
Short-Circuit Current High
Output Impedance to GND
Shorted to V
CC
Input Code = 0
250
50
500
AC Performance
Voltage Output Slew Rate
Voltage Output Settling Time
Digital Feedthrough
5kΩ in Parallel with 100pF
●
●
1.0
2.4
V/µs
µs
To ±1/2LSB, 5kΩ in Parallel with 100pF, V = 4.75V
6
CC
(Notes 2,3)
nV/s
Digital I/O
V
V
V
V
Digital Input High Voltage
Digital Input Low Voltage
Digital Output High Voltage
Digital Output Low Voltage
Digital Input Leakage
●
●
●
●
●
●
V
V
IH
IL
0.8
I
I
= –1mA, D
Only
V – 1
CC
V
OH
OL
OUT
OUT
OUT
= 1mA, D
Only
0.4
V
OUT
I
V
= GND to V
CC
±10
µA
pF
LEAK
IN
C
Digital Input Capacitance
(Note 2)
10
IN
Switching (Note 2)
t1
t2
t3
t4
t5
t6
t7
t8
D
D
Valid to CLK Setup
Valid to CLK Hold
●
●
●
●
●
●
●
●
100
25
ns
ns
IN
IN
CLK High Time
350
350
150
0
ns
CLK Low Time
ns
LOAD Pulse Width
LSB CLK to LOAD
LOAD High to CLK
ns
ns
0
ns
D
OUT
Output Delay
C
= 15pF
LOAD
35
150
1.4
ns
f
Maximum Clock Frequency
MHz
CLK
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 3: DAC switched from all 1s to all 0s, and all 0s to all 1s code.
Note 4: Guaranteed with internal V or with external V range of
REF
REF
Note 2: Guaranteed by design; not subject to test.
2.475V to 12V. Tested at 10V.
3
LTC1257
TYPICAL PERFOR A CE CHARACTERISTICS
U W
Minimum Supply Voltage
vs Load Current #2
Minimum Supply Voltage
vs Load Current #1
Supply Current vs Temperature
15.0
14.5
14.0
13.5
13.0
12.5
12.0
11.5
11.0
0.38
0.37
0.36
0.35
0.34
0.33
0.32
0.31
5.0
4.8
4.6
4.4
4.2
4.0
3.8
3.6
3.4
3.2
3.0
V
V
T
= 10V
V
V
T
= INTERNAL
REF
OUT
A
REF
OUT
A
= FULL SCALE
= FULL SCALE
V
= 5.25V
= 25°C
= 25°C
CC
V
= 5V
CC
V
= 4.75V
CC
50
TEMPERATURE (°C)
100 125
0.01
0.1
1
10
–50 –25
0
25
75
0.01
0.1
1
10
OUTPUT LOAD CURRENT (mA)
OUTPUT LOAD CURRENT (mA)
1257 G02
1257 G01
1257 G03
Pull-Down Voltage vs Output Sink
Current Capability
Supply Current vs
Logic Input Voltage
Output Swing vs Load Resistance
1000
100
10
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0.59
0.54
0.49
0.44
0.39
0.34
V
A
= 5V
= 25°C
V
= 5V
CC
CC
T
ZERO SCALE
TIED TO V
R
L
CC
FULL SCALE
TIED TO GND
HOT
R
L
COLD
ROOM
1
0.1
1
10
100
1000
0
1
2
3
4
5
10
100
1k
10k
OUTPUT SINK CURRENT (µA)
LOGIC VOLTAGE (V)
LOAD RESISTANCE (Ω)
1257 G05
1257 G06
1257 G04
Full-Scale Voltage vs
Temperature
Zero-Scale Voltage vs
Temperature
Integral Nonlinearity (INL)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
2.0
1.6
2.0495
2.0490
2.0485
2.0480
2.0475
2.0470
2.0465
V
= 5V
CC
V
= 5V
CC
INTERNAL REFERENCE
INTERNAL REFERENCE
1.2
0.8
0.4
0
–0.4
–0.8
–1.2
–1.6
–2.0
V
= 5V
CC
INTERNAL REFERENCE
= 25°C
T
A
50
TEMPERATURE (°C)
100 125
–50 –25
0
25
50
125
3584
4096
–50 –25
0
25
75
0
75 100
512 1024 1536 2048 2560 3072
CODE
TEMPERATURE (°C)
1257 G07
1257 G08
1257 G09
4
LTC1257
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Reference Compensation
Resistance vs CL
Broadband Noise
Differential Nonlinearity (DNL)
70
60
50
40
30
20
10
0
0.5
CODE = FFF
H
BW = 3Hz TO 1MHz
GAIN = 1100×
0.0
–0.5
0.01
0.1
1
(µF)
10
100
0
512 1024 1536 2048 2560 3072 3584 4098
CODE
TIME = 5ms/DIV
1257 G12
C
L
1257 G11
1257 TA05
U
U
U
PI FU CTIO S
CLK (Pin 1): The TTL level input for the serial interface
GND (Pin 5): Ground.
clock.
REF (Pin 6): The output of the 2.048V reference and the
inputtotheDACresistorladder.Anexternalreferencewith
voltagefrom2.475VtoVCC –2.7Vmaybeusedtooverride
the internal reference.
DIN(Pin2): TheTTLlevelinputfortheserialinterfacedata.
Data on the DIN pin is latched into the shift register on the
rising edge of the serial clock.
LOAD (Pin 3): The TTL level input for the serial interface
load control. Data is loaded from the shift register into the
DAC register, thus updating the DAC output when LOAD is
pulled low. The DAC register is transparent as long as
LOAD is held low.
VOUT (Pin 7): The buffered DAC output is capable of
sourcing 2mA over temperature while pulling within 2.7V
of VCC. The output will pull to ground through an internal
250Ω equivalent resistance.
VCC (Pin 8): The positive supply input. 4.75V ≤ VCC
≤
DOUT(Pin 4): The output of the shift register which
becomes valid on the rising edge of the serial clock. The
DOUT pin is driven from GND to VCC by an internal CMOS
inverter. MultipleLTC1257smaybecascadedbyconnect-
ing the DOUT pin to the DIN pin of the next chip.
15.75V. Requires a bypass capacitor to ground.
5
LTC1257
U U
DEFI ITIO S
LSB: Theleastsignificantbitortheidealvoltagedifference
Offset Error: The theoretical voltage at the output when
the DAC is loaded with all zeros. The output amplifier can
have a true negative offset, but because the part is oper-
ated from a single supply, the output cannot go below
ground.Iftheoffsetisnegative,theoutputwillremainnear
0V resulting in the transfer curve shown in Figure 1.
between two successive codes.
LSB = (VFS – VOS)/2n – 1
n
= The number of digital input bits
VOS = The zero code error or offset of the DAC
VFS = The full-scale output voltage of the DAC
measured when all bits are set to 1
OUTPUT
VOLTAGE
Resolution: The resolution is the number of DAC output
states (2n) that divide the full-scale range. The resolution
does not imply linearity.
0V
NEGATIVE
OFFSET
DAC CODE
{
1257 F01
INL: End-point integral nonlinearity is the maximum de-
viationfromastraightlinepassingthroughtheend-points
of the DAC transfer curve. Because the part operates from
a single supply and the output cannot go below ground,
the linearity is measured between full-scale and the first
code that guarantees a positive output. The INL error at a
given input code is calculated as follows:
Figure 1. Effect of Negative Offset
The offset of the part is measured at the first code that
produces an output voltage 0.5LSB greater than the pre-
vious code:
VOS = VOUT – [(Code)(VFS)/(2n – 1)]
Full-Scale Error: Full-scale error is the difference be-
tweentheidealandmeasuredDACoutputvoltageswithall
bits set to one (Code = 4095). The full-scale error includes
the offset error and is calculated as follows:
INL = (VOUT – VIDEAL)/LSB
VIDEAL = (Code)(LSB) + VOS
VOUT = The output voltage of the DAC measured at
the given input code
FSE = (VOUT – VIDEAL)/LSB
VIDEAL = (VREF)(1 – 2–n) – VOS
VREF = The reference voltage, either internal or
external
DNL: Differential nonlinearity is the difference between
the measured change and the ideal 1LSB change between
any two adjacent codes. The DNL error between any two
codes is calculated as follows:
Gain Error: Gain error is the difference between the ideal
and measured slope of the DAC transfer characteristic.
Gain error is equal to full-scale error minus offset error.
DNL = (∆VOUT – LSB)/LSB
∆VOUT = The measured voltage difference between
two adjacent codes
DigitalFeedthrough: Theglitchthatappearsattheanalog
outputcausedbyACcouplingfromthedigitalinputswhen
they change state. The area of the glitch is specified in
(nV)(sec).
6
LTC1257
W
BLOCK DIAGRA
LOGIC
5V REGULATOR
V
D
CC
SUPPLY
CLK
12-BIT
SHIFT REGISTER
OUT
D
IN
12
GND
LOAD
REF
12-BIT LATCH
12
+
–
2.048V REFERENCE
DAC
V
OUT
1257 BD
W U
W
TI I G DIAGRA
t
t
t
t
2
1
6
7
CLK
t
t
3
4
B11
MSB
B0
LSB
B10
B1
D
IN
t
5
LOAD
t
8
B11
(PREVIOUS WORD)
B11
D
B1
B10
B0
OUT
CURRENT WORD
1257 TD
7
LTC1257
U
OPERATIO
Reference
Serial Interface
The LTC1257 includes an internal 2.048V reference, mak-
ing 1LSB equal to 500µV. The internal reference output is
turned off when the pin is forced above the reference
voltage, allowing an external reference to be connected to
the reference pin. The external reference must be greater
than 2.475V and less than VCC – 2.7V, and be capable of
driving the 10k minimum DAC resistor ladder.
The data on the DIN input is loaded into the shift register
on the rising edge of the clock. The MSB is loaded first and
theLSBlast. TheDACregisterloadsthedatafromtheshift
register when LOAD is pulled low, and remains transpar-
ent until LOAD is pulled high and the data is latched.
An internal 5V regulator provides the supply for the digital
logic. By limiting the internal digital signal swings to 5V,
digital noise is reduced. The buffered output of the 12-bit
shift register is available on the DOUT pin which will swing
from GND to VCC.
If the reference output is driving a large capacitive load, a
series resistor must be added to insure stability. For any
capacitive load greater than 1µF, a 10Ω series resistor will
suffice.
Multiple LTC1257s may be daisy chained together by
connecting the DOUT pin to the DIN pin of the next chip,
while the clock and load signals remain common to all
chips in the daisy chain. The serial data is clocked to all of
the chips, then the LOAD signal is pulled low to update all
of them simultaneously. The maximum clocking rate is
1.4MHz.
Voltage Output
The LTC1257 voltage output is able to pull within 2.7V of
VCC while sourcing 2mA. A internal NMOS transistor with
a 200Ω equivalent impedance pulls the output to ground.
The output is protected against short circuits and is able
to drive up to a 500pF capacitive load without oscillation.
If digital noise on the output causes a problem, a simple
100Ω, 0.1µF RC circuit can be used to filter the noise.
U
TYPICAL APPLICATIO S
DAC with External Reference
Filtering VREF and VOUT
15V
V
CC
IN
0.1µF
LT1021-10
GND
0.1µF
OUT
D
IN
V
CC
100Ω
5%
CLK
V
OUT
V
OUT
LTC1257
GND
V
D
IN
V
CC
REF
LOAD
CLK
0.1µF
D
OUT
V
REF
LTC1257
µP
V
CONTROL OUTPUT
OUT
LOAD
1µF
D
GND
1257 TA06
OUT
10Ω
5%
1257 TA03
8
LTC1257
U
TYPICAL APPLICATIO S
Auto Ranging 8-Channel ADC with Shutdown
22µF
5V
V
CH0
CC
CS
8 ANALOG
INPUT CHANNELS
D
•
•
•
OUT
µP
LTC1296
CLK
D
CH7
IN
COM
REF
+
–
REF
SSO
50k
50k
5V
74HC04
0.1µF
100Ω
V
D
IN
CC
CLK
LTC1257
V
OUT
LOAD
0.1µF
D
V
GND
OUT
REF
V
D
IN
CC
100Ω
0.1µF
CLK
LTC1257
V
OUT
LOAD
D
OUT
GND
V
REF
1257 TA02
12-Bit Single 5V Control System with Shutdown
5V
100k
10k
10µF
2N3906
CB/POWER DOWN
CLK
V
CC
–IN
+IN
CS
D
0.1µF
V
OUT
IN
DATA
µP
J
–
+
CLK
DAC LOAD
LTC1297
ADC
LT1025A
GND COMMON
V
REF
GND
+
–
47k
10µF
LTC1050
74k
1µF
1µF
100k
V
D
IN
V
CC
REF
CLK
CONTORL
OUTPUT
LTC1257
V
OUT
1k
LOAD
D
OUT
GND
1257 TA04
9
LTC1257
U
PACKAGE DESCRIPTIO
N8 Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
0.400*
(10.160)
MAX
8
7
6
5
4
0.255 ± 0.015*
(6.477 ± 0.381)
1
2
3
0.130 ± 0.005
0.300 – 0.325
0.045 – 0.065
(3.302 ± 0.127)
(1.143 – 1.651)
(7.620 – 8.255)
0.065
(1.651)
TYP
0.009 – 0.015
(0.229 – 0.381)
0.125
0.020
(0.508)
MIN
(3.175)
MIN
+0.035
0.325
–0.015
0.018 ± 0.003
(0.457 ± 0.076)
0.100
(2.54)
BSC
+0.889
8.255
(
)
N8 1098
–0.381
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
10
LTC1257
U
PACKAGE DESCRIPTIO
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
7
5
8
6
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
3
4
2
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.050
(1.270)
BSC
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
SO8 1298
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
11
LTC1257
U
O
TYPICAL APPLICATI
Driving LTC1257 with Optoisolators
12V
LT1021-5
V
V
IN
OUT
2k
5%
2k
5%
2k
5%
0.1µF
CLK
V
CC
V
REF
MOC5008
MOC5008
MOC5008
6
D
IN
V
V
OUT
1
OUT
LTC1257
GND
CLK
LOAD
4
5
D
OUT
2
1
6
4
5
D
IN
2
6
4
5
1
2
LOAD
1257 TA07
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1446: V = 4.5V to 5.5V, V
12 Bit
LTC1446/LTC1446L Dual 12-Bit V
DACs in SO-8 Package
= 0V to 4.095V
OUT
OUT
OUT
CC
LTC1446L: V = 2.7V to 5.5V, V
= 0V to 2.5V
CC
LTC1448
Dual 12-Bit V
DAC in SO-8 Package, V : 2.7V to 5.5V
Output Swings from GND to REF,
REF Input Can Be Tied to V
OUT
CC
CC
LTC1450/LTC1450L Single 12-Bit V
DACs with Parallel Interface
LTC1450: V = 4.5V to 5.5V, V = 0V to 4.095V
OUT
OUT
CC
LTC1450L: V = 2.7V to 5.5V, V
= 0V to 2.5V
CC
OUT
LTC1451
LTC1452
LTC1453
Single Rail-to-Rail 12-Bit V
DAC, Full Scale: 4.095V, V : 4.5V to
Low Power, Complete V
DAC in SO-8 Package
OUT
CC
OUT
5.5V, Internal 2.048V Reference Brought Out to Pin
Single Rail-to-Rail 12-Bit V
Multiplying DAC, V : 2.7V to 5.5V
Low Power, Multiplying V
Buffer Amplifier in SO-8 Package
DAC with Rail-to-Rail
OUT
CC
OUT
Single Rail-to-Rail 12-Bit V
DAC, Full Scale: 2.5V, V : 2.7V to 5.5V
3V, Low Power, Complete V DAC in SO-8 Package
OUT
CC
OUT
LTC1454/LTC1454L Dual 12-Bit V
DACs in SO-16 Package with Added Functionality
LTC1454: V = 4.5V to 5.5V, V
= 0V to 4.095V
OUT
OUT
CC
OUT
LTC1454L: V = 2.7V to 5.5V, V
= 0V to 2.5V
CC
LTC1456
Single Rail-to-Rail Output 12-Bit DAC with Clear Pin,
Full Scale: 4.095V, V : 4.5V to 5.5V
Low Power, Complete V
DAC in SO-8
OUT
Package with Clear Pin
CC
LTC1458/LTC1458L Quad 12 Bit Rail-to-Rail Output DACs with Added Functionality
LTC1458: V = 4.5V to 5.5V, V
= 0V to 4.095V
OUT
CC
OUT
LTC1458L: V = 2.7V to 5.5V, V
= 0V to 2.5V
CC
LTC1659
Single Rail-to-Rail 12-Bit V
CC
DAC in MSOP-8 Package,
Output Swings from GND to REF,
REF Input Can Be Tied to V
OUT
V
= 2.7V to 5.5V
CC
14 Bit
LTC1658
14-Bit Rail-to-Rail Micropower DAC in MSOP, V = 2.7V to 5.5V
Output Swings from GND to REF,
REF Input Can Be Tied to V
CC
CC
LTC1654
16 Bit
Dual 14-Bit V
DAC
Programmable Speed/Power, SO-8 Footprint
OUT
LTC1655(L)
Single 16-Bit V
DAC with Serial Interface in SO-8
V
V
= 5V (3V), Low Power, Deglitched,
OUT
OUT
CC
= 0V to 4.096V (0V to 2.5V)
1257fb LT/TP 1101 REV B 1.5K • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
12
●
●
LINEAR TECHNOLOGY CORPORATION 1994
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号:
LTC1257CS8#TR
LTC1257 - Complete Single Supply 12-Bit Voltage Output DAC in SO-8; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC1257CS8#TRPBF
LTC1257 - Complete Single Supply 12-Bit Voltage Output DAC in SO-8; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC1257IS8#TR
LTC1257 - Complete Single Supply 12-Bit Voltage Output DAC in SO-8; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C
Linear
©2020 ICPDF网 联系我们和版权申明