LTC1685IS8#TR [Linear]
LTC1685 - 52Mbps, Precision Delay, RS485 Fail-Safe Transceiver; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C;
| 型号： | LTC1685IS8#TR |
| 厂家： | 
Linear |
| 描述： | LTC1685 - 52Mbps, Precision Delay, RS485 Fail-Safe Transceiver; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C 驱动 光电二极管 接口集成电路 驱动器 |
| 文件： | 总12页 (文件大小：190K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LTC1685
52Mbps, Precision Delay,
RS485 Fail-Safe Transceiver
U
DESCRIPTIO
FEATURES
The LTC®1685 is a high speed, precision delay RS485
transceiverthatcanoperateatdataratesashighas52Mbps.
The device also meets the requirements of RS422.
■
Precision Propagation Delay Over Temperature:
Receiver/Driver: 18.5ns
High Data Rate: 52Mbps
Low tPLH/tPHL Skew:
±3.5ns
■
■
A unique architecture provides very stable propagation
delays and low skew over a wide common mode and
ambient temperature range.
Receiver/Driver: 500ps Typ
■
■
–7V to 12V RS485 Input Common Mode Range
Guaranteed Fail-Safe Receiver Operation Over the
Entire Common Mode Range
High Receiver Input Resistance: ≥22k, Even When
Unpowered
Short-Circuit Protected
Thermal Shutdown Protected
Driver Maintains High Impedance in Three-State or
with Power Off
Single 5V Supply
Pin Compatible with LTC485
The driver and receiver feature three-state outputs, with
disabled driver outputs maintaining high impedance over
the entire common mode range. A short circuit feature
detects shorted outputs and substantially reduces driver
output current. A similar feature also protects the receiver
output from short circuits. Thermal shutdown circuitry
protects from excessive power dissipation.
■
■
■
■
■
■
■
The receiver has a fail-safe feature that guarantees a high
output state when the inputs are shorted or are left floating.
The LTC1685 RS485 transceiver guarantees receiver fail-
safe operation over the entire common mode range (–7V
to 12V). Input resistance will remain ≥22k when the device
is unpowered or disabled.
45dB CMRR at 2U6MHz
APPLICATIO S
■
High Speed RS485/RS422 Transceivers
■
Level Translator
Backplane Transceiver
STS-1/OC-1 Data Transceiver
The LTC1685 operates from a single 5V supply and draws
only 7mA of supply current.
■
■
, LTC and LT are registered trademarks of Linear Technology Corporation.
■
Fast-20, Fast-40 SCSI Transceivers
U
TYPICAL APPLICATION
10Mbps Data Pulse
400ft Category 5 UTP
RO1
V
CC1
R
RE1
DE1
DI1
DRIVER INPUT
2V/DIV
Rt
Rt
CABLE DELAY
D
GND1
RECEIVER
INPUT
1V/DIV
5V/DIV
RO2
RE2
DE2
DI2
V
CC2
R
RECEIVER
OUTPUT
D
GND2
100ns/DIV
1685 TA01
1685 TA02
1
LTC1685
W W W
U
W
U
ABSOLUTE AXI U RATI GS
/O
PACKAGE RDER I FOR ATIO
(Note 1)
Supply Voltage (VDD).............................................. 10V
Control Input Currents .................... –100mA to 100mA
Control Input Voltages .................. –0.5V to VDD + 0.5V
Driver Input Voltages .................... –0.5V to VDD + 0.5V
Driver Output Voltages .................................. +12V/–7V
Receiver Input Voltages ................................. +12V/–7V
Receiver Output Voltages ............. –0.5V to VDD + 0.5V
Receiver Input Differential ...................................... 10V
Short-Circuit Duration (Driver VOUT: –7V to 10V,
TOP VIEW
ORDER PART
NUMBER
RO
RE
DE
DI
1
2
3
4
V
B
A
8
7
6
5
DD
R
LTC1685CS8
LTC1685IS8
D
GND
S8 PART MARKING
S8 PACKAGE
8-LEAD PLASTIC SO
1685
1685I
TJMAX = 125°C, θJA = 150°C/ W
Receiver VOUT: 0V to VDD) ............................... Indefinite
Operating Temperature Range
Consult factory for Military grade parts.
LTC1685C ............................................... 0°C to 70°C
LTC1685I............................................. –40°C to 85°C
Storage Temperature Range ................ –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................. 300°C
DC ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDD = 5V ± 5%, unless otherwise noted. (Notes 2, 3)
SYMBOL PARAMETER
CONDITIONS
= 0
MIN
TYP
MAX
UNITS
V
OD1
V
OD2
Differential Driver Output (Unloaded)
Differential Driver Output (With Load)
I
●
V
V
OUT
DD
R = 50Ω (RS422)
R = 27Ω (RS485), Figure 1
2
1.5
V
V
●
●
V
DD
∆V
Change in Magnitude of Driver Differential
Output Voltage for Complementary
Output States
R = 27Ω or 50Ω, Figure 1
0.2
V
OD
V
Driver Common Mode Output Voltage
R = 27Ω or 50Ω, V = 5V, Figure 1
●
●
2
3
V
V
OC
DD
∆ V
Change in Magnitude of Driver Common
Mode Output Voltage for Complementary
Output States
R = 27Ω or 50Ω, Figure 1
0.2
OC
V
V
Input High Voltage
Input Low Voltage
Input Current
DE, DI, RE
DE, DI, RE
DE, DI, RE
●
●
●
2
V
V
IH
0.8
1
IL
I
I
–1
µA
IN1
IN2
Input Current (A, B)
V , V = 12V, DE = 0, V = 0V or 5.25V
●
●
500
µA
µA
A
B
DD
V , V = –7V, DE = 0, V = 0V or 5.25V
–500
–0.3
A
B
DD
V
TH
Differential Input Threshold Voltage
for Receiver
–7V ≤ V ≤ 12V
●
0.3
V
CM
∆V
Receiver Input Hysteresis
Receiver Output High Voltage
Receiver Output Low Voltage
V
= 0V
25
mV
V
TH
CM
OUT
OUT
V
V
I
I
= –4mA, V = 300mV
●
●
●
3.5
–1
4.8
OH
ID
= 4mA, V = –300mV
0.4
1
V
OL
ID
I
Three-State (High Impedance) Output
Current at Receiver
0.4V ≤ V
≤ 2.4V
OUT
µA
OZR
I
I
Supply Current
No Load, Pins 2, 3, 4 = 0V or V
●
●
7
12
20
mA
mA
DD
DD
Driver Short-Circuit Current, V
= HIGH
V
OUT
= –7V or 10V (Note 5)
OSD1
OUT
2
LTC1685
DC ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDD = 5V ±5%, unless otherwise noted. (Notes 2, 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
20
UNITS
mA
mA
kΩ
pF
I
I
Driver Short-Circuit Current, V
Receiver Short-Circuit Current
Input Resistance
= LOW
V
OUT
V
OUT
= –7V or 10V (Note 5)
●
●
●
OSD2
OSR
OUT
= 0V or V (Note 5)
20
DD
R
IN
–7V ≤ V ≤ 12V
22
CM
C
IN
Input Capacitance
A, B Inputs, D, DE, RE
3
3.3
2
Open-Circuit Input Voltage, Figure 5
Fail-Safe Time Time to Detect Fail-Safe Condition
CMRR Receiver Input Common Mode Rejection Ratio
V
DD
= 5V (Note 4)
●
●
3.2
3.4
V
µs
V
CM
= 2.6V, f = 26MHz
45
dB
C
LOAD
Receiver and Driver Output Load Capacitance
(Note 4)
500
pF
U
SWITCHING CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VDD = 5V, unless otherwise noted. (Notes 2, 3)
SYMBOL PARAMETER
CONDITIONS
= 54Ω, C = C = 100pF, Figures 3, 5,
LTC1685C
LTC1685I
MIN
TYP
MAX
UNITS
t
, t
Driver Input-to-Output
Propagation Delay
R
DIFF
PLH PHL
L1
L2
●
●
15
13
18.5
18.5
22
25
ns
ns
t
Driver Output A-to-Output
B Skew
R
= 54Ω, C = C = 100pF,
500
ps
SKEW
DIFF
L1
L2
Figures 3, 5
t , t
r
Driver Rise/Fall Time
R
DIFF
Figures 3, 5
= 54Ω, C = C = 100pF,
3.5
ns
f
L1
L2
t
t
t
t
t
Driver Enable to Output High
Driver Enable to Output Low
Driver Disable from Low
Driver Disable from High
C = 100pF, S2 Closed, Figures 4, 6
●
●
●
●
25
25
25
25
50
50
50
50
ns
ns
ns
ns
ZH
ZL
LZ
HZ
L
C = 100pF, S1 Closed, Figures 4, 6
L
C = 15pF, S1 Closed, Figures 4, 6
L
C = 15pF, S2 Closed, Figures 4, 6
L
, t
Receiver Input-to-Output
Propagation Delay
C = 15pF, Figures 3, 7
PLH PHL
L
LTC1685C
LTC1685I
●
●
15
13
18.5
18.5
22
25
ns
ns
t
t
t
t
t
Receiver Skew t
– t
C = 15pF, Figures 3, 7
500
25
ps
ns
ns
ns
ns
ns
SQD
ZL
PLH
PHL
L
Receiver Enable to Output Low C = 15pF, S1 Closed, Figures 2, 8
●
●
●
●
●
50
50
L
Receiver Enable to Output High C = 15pF, S2 Closed, Figures 2, 8
25
ZH
LZ
L
Receiver Disable from Low
Receiver Disable from High
C = 15pF, S1 Closed, Figures 2, 8
L
25
50
C = 15pF, S2 Closed, Figures 2, 8
L
25
50
HZ
Maximum Receiver Input
Rise/Fall Times
(Note 4)
2000
t
Package-to-Package Skew
Minimum Input Pulse Width
Same Temperature (Note 4)
1.5
ns
PKG-PKG
V
= 5V ± 5% (Note 4)
DD
LTC1685C
LTC1685I
●
●
17
20
19.2
25
ns
ns
Maximum Data Rate
V
= 5V ± 5% (Note 4)
DD
LTC1685C
LTC1685I
●
●
52
40
60
50
Mbps
Mbps
Maximum Input Frequency
V
= 5V ± 5% (Note 4)
DD
LTC1685C
LTC1685I
●
●
26
20
30
25
MHz
MHz
3
LTC1685
U
SWITCHING CHARACTERISTICS
Note 1: Absolute Maximum Ratings are those values beyond which the life
Note 4: Guaranteed by design, but not tested.
of a device may be impaired.
Note 2: All currents into the device pins are positive; all currents out of the
device pins are negative.
Note 3: All typicals are given for V = 5V, T = 25°C.
Note 5: Short-circuit current does not represent output drive capability.
When the output detects a short-circuit condition, output drive current is
significantly reduced (from hundreds of mA to 20mA max) until the short
is removed.
DD
A
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Receiver Input CMRR
Supply Current vs Data Rate
Supply Current vs Temperature
46.5
46.0
45.5
45.0
44.5
44.0
43.5
43.0
42.5
70
60
59
58
BOTH DRIVER AND RECEIVER
ENABLED AND LOADED
A
T
= 25°C
57
56
55
54
53
52
51
50
50
40
30
20
10
0
BOTH DRIVER AND RECEIVER
ENABLED AND LOADED
25Mbps DATA RATE
T
= 25°C
A
42.0
0
25
75
–50
–25
100
50
10
20
DATA RATE (Mbps)
50
1
30
40
10
1k
100k
FREQUENCY (Hz)
1M
TEMPERATURE (°C)
1685 G03
1685 G02
1685 G01
Receiver Propagation Delay
vs Load Capacitance
Receiver Propagation Delay
vs Common Mode
Receiver Propagation Delay
vs Input Overdrive
25
20
15
10
5
30
25
20
15
10
5
25
20
T
= 25°C
T = 25°C
A
T
A
= 25°C
A
15
10
5
0
0
0
5
25
35
55
105
205
0.3 0.5 0.7
1.0 1.25 1.5 2.0 2.5
15
–7 –4 –2
0
2
4
6
8
10 12
LOAD CAPACITANCE (pF)
RECEIVER INPUT OVERDRIVE (V)
RECEIVER COMMON MODE (V)
1685 G04
1685 G06
1685 G05
4
LTC1685
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Receiver Propagation Delay
vs Temperature
Receiver Maximum Data Rate
vs Input Overdrive
Driver Propagation Delay
vs Temperature
25
20
15
10
5
25
20
15
10
70
60
T
= 25°C
A
50
40
30
20
10
5
0
0
0
–40 –20
20
40
60
80
100
50
75 100 125
0.3 0.4
0.5 0.6
0.7
1.0
1.5
2.5
0
–50 –25
0
25
TEMPERATURE (°C)
TEMPERATURE (°C)
RECEIVER INPUT DIFFERENTIAL (V)
1685 G07
1680 G09
1685 G10
Driver Propagation Delay
vs Capacitive Load
Driver Propagation Delay
vs Driver Input Voltage
19.0
18.5
18.0
17.5
17.0
16.5
16.0
25
20
15
10
5
T
= 25°C
V
= 5V
A
DD
INPUT THRESHOLD = 1.5V
T
A
= 25°C
t
HL
t
LH
0
5
25
50
75
100
150
15
2.5
3.0
3.5
4.0
4.5
5.0
LOAD CAPACITANCE (pF)
DRIVER INPUT VOLTAGE (V)
1685 G11
1685 G08
U
U
U
PIN FUNCTIONS
DI (Pin 4): Driver Input. Controls the states of the A and
B outputs only if DE = High. If DE = Low, DI will have no
effect on A and B pins. Do not float.
RO (Pin 1): Receiver Output. If A ≥ B by 300mV, then RO
will be high. If A ≤ B by 300mV, then RO will be low.
RE (Pin 2): Receiver Enable. RE = Low enables the
receiver. RE = High forces receiver output into high
impedance state. Do not float.
GND (Pin 5): Ground.
A (Pin 6): Noninverting Receiver Input/Driver Output.
B (Pin 7): Inverting Receiver Input/Driver Output.
DE (Pin 3): Driver Enable. DE = High enables the driver.
DE=Lowwillforcethedriveroutputintoahighimpedance
state and the device will function as a line receiver if RE is
also low. Do not float.
VDD (Pin 8): Positive Supply, 5V to ±5%. Bypass with
0.1µF ceramic capacitor.
5
LTC1685
U
U
FU CTIO TABLES
Receiving
INPUTS
RE
Transmitting
OUTPUT
RO
INPUTS
DE
LINE
OUTPUTS
DE
0
A – B
RE
X
DI
1
CONDITION
No Fault
No Fault
X
B
0
A
1
0
≥ 300mV
1
0
1
1
1
1
0
1
0
0
≤ –300mV
Inputs Open
X
0
1
0
0
0
X
X
X
Hi-Z
Hi-Z
0
0
Inputs Shorted Together
A = B = –7V to 12V
X
Fault
±10mA Current Source
1
X
X
Hi-Z
TEST CIRCUITS
A
S1
S2
TEST POINT
1k
R
RECEIVER
OUTPUT
V
DD
V
OD
C
L
15pF
1k
V
OC
R
1685 F02
B
1685 F01
Figure 2. Driver DC Test Load
Figure 1. Driver DC Test Load
3V
DE
A
C
A
B
L1
S1
RO
DI
R
DIFF
V
DD
B
500Ω
C
OUTPUT
UNDER TEST
L2
RE
S2
15pF
C
L
1685 F04
1685 F03
Figure 3. Driver/Receiver Timing Test Circuit
Figure 4. Driver Timing Test Load #2
6
LTC1685
U W
W
SWITCHI G TI E WAVEFOR S
3V
f = 1MHz, t ≤ 3ns, t ≤ 3ns
DI
1.5V
1.5V
r
f
0V
B
1/2 V
O
t
t
PHL
PLH
V
O
A
t
t
SKEW
1/2 V
SKEW
O
90%
10%
V
O
90%
V
= V(A) – V(B)
DIFF
0V
10%
–V
O
1586 F05
t
t
f
r
Figure 5. Driver Propagation Delays
3V
0V
5V
f = 1MHz, t ≤ 3ns, t ≤ 3ns
1.5V
1.5V
DE
r
f
t
t
LZ
ZL
A, B
A, B
2.5V
OUTPUT NORMALLY LOW
OUTPUT NORMALLY HIGH
0.5V
0.5V
V
OL
OH
0V
V
2.5V
t
1686 F06
t
HZ
ZH
Figure 6. Driver Enable and Disable Times
V
OH
2.5V
2.5V
RO
OUTPUT
V
OL
f = 1MHz, t ≤ 3ns, t ≤ 3ns
t
t
PLH
r
f
PHL
V
A – B
–V
OD2
OD2
0V
INPUT
1686 F07
Figure 7. Receiver Propagation Delays
3V
0V
5V
1.5V
f = 1MHz, t ≤ 3ns, t ≤ 3ns
1.5V
RE
RO
RO
r
f
t
t
LZ
ZL
2.5V
OUTPUT NORMALLY LOW
OUTPUT NORMALLY HIGH
0.5V
0.5V
2.5V
0V
t
1685 F08
t
HZ
ZH
Figure 8. Receiver Enable and Disable Times
7
LTC1685
U U
U
EQUIVALENT INPUT NETWORKS
≥22k
≥22k
≥22k
A
A
B
3.3V
≥22k
B
3.3V
DE = 0, RE = 0 OR 1
DD
V
DD
= 0V
V
= 5V
1685 F09
Figure 9. Input Thevenin Equivalent
U
W U U
APPLICATIONS INFORMATION
Theory of Operation
Fail-Safe Features
Unlike typical CMOS transceivers whose propagation
delay can vary by as much as 500% from package to
package and show significant temperature drift, the
LTC1685 employs a novel architecture that produces a
tightlycontrolledandtemperaturecompensatedpropaga-
tion delay. The differential timing skew is also minimized
between rising and falling output edges of the receiver
output and the complementary driver outputs.
The LTC1685 has a fail-safe feature that guarantees the
receiver output to be in a logic HIGH state when the inputs
are either shorted or left open (note that when inputs are
left open, large external leakage currents might override
the fail-safe circuitry). In order to maintain good high
frequency performance, it was necessary to slow down
the transient response of the fail-safe feature. When a line
fault is detected, the output will go HIGH typically in 2µs.
NotethattheLTC1685guaranteesfail-safeperformance
over the entire (–7V to 12V) common mode range!
The precision timing features of the LTC1685 reduce
overall system timing constraints by providing a narrow
±3.5ns window during which valid data appears at the
receiver/driver output. The driver and receiver pair will
havepropagationdelaysthattypicallymatchtowithin1ns.
When the inputs are accidentally shorted (by cutting
through a cable, for example), the short circuit fail-safe
feature will guarantee a high output logic level. Note also
that if the line driver is removed and the termination
resistors are left in place, the receiver will see this as a
“short” and output a logic HIGH. Both of these fail-safe
features will keep the receiver from outputting false data
pulses under line fault conditions.
In clocked data systems, the low skew minimizes duty
cycle distortion of the clock signal. The LTC1685 can be
used at data rates of 52Mbps with less than 5% duty cycle
distortion (depending on cable length). When a clock
signalisusedtoretimeparalleldata, themaximumrecom-
mended data transmission rate is 26Mbps to avoid timing
errors due to clock distortion.
Thermal shutdown and short-circuit protection prevent
latchup damage to the LTC1685 during fault conditions.
8
LTC1685
U
W U U
APPLICATIONS INFORMATION
terminators, see Figure 15), the LTC1685 will not come
outofshort-circuitmodeautomaticallyuponreleaseofthe
physical short. In order to resume normal operation, the
DE pin has to be pulsed low for at least 200ns.
Output Short-Circuit Protection
The LTC1685 employs voltage sensing short-circuit pro-
tection at the output terminals of both the driver and
receiver. For a given input polarity, this circuitry deter-
mineswhatthecorrectoutputlevelshouldbe.Iftheoutput
level is different from the expected, it shuts off the big
output devices. For example, if the driver input is >2V, it
expects the “A” output to be >3.25V and the “B” output to
be <1.75V. If the “A” output is subsequently shorted to a
voltage below VDD/2, this circuitry shuts off the big output
devices and turns on a smaller device in its place (the
converse applies for the “B” output). The outputs then
appearas±10mAcurrentsources.Notethatundernormal
operation, the output drivers can sink/source >50mA. A
time-out period of about 50ns is used in order to maintain
normal high frequency operation, even under heavy ca-
pacitive loads.
High Speed Twisted Pair Transmission
Data rates up to 52Mbps can be transmitted over 100ft of
category 5 twisted pair. Figure 10 shows the LTC1685
receiving differential data from another LTC1685 trans-
ceiver. Figure 11a shows a 26MHz (52Mbps) square wave
propagated over 100ft of category 5 UTP. Figure 11b
shows a more stringent case of propagating a single 20ns
pulse over 100ft of category 5 UTP. Figure 12 shows a
4Mbps square wave over 1000ft of category 5 unshielded
twisted pair.
If the cable is shorted at a large distance from the device
outputs, it is possible for the short to go unnoticed at the
driver outputs due to parasitic cable resistance. Addition-
ally, when the cable is shorted, it no longer appears as an
ideal transmission line, and the parasitic Ls and Cs might
giverisetoringingandevenoscillation.Alltheseconditions
disappearoncethedevicecomesoutofshort-circuitmode.
DRIVER
2V/DIV
2V/DIV
INPUT
RECEIVER
OUTPUT
For cables with the typical RS485 termination (no DC bias
on the cable, such as Figure 10), the LTC1685 will auto-
maticallycomeoutofshort-circuitmodeoncethephysical
short has been removed. With cable terminations with a
DC bias (such as Fast-20 and Fast-40 differential SCSI
10ns/DIV
1685 F11
Figure 11a. 100ft of Category 5 UTP: 50Mbps
DRIVER
INPUT
2V/DIV
CABLE DELAY
RE
2
RE
2
1
4
1
4
RO
DI
RO
DI
RECEIVER
INPUT
2V/DIV
5V/DIV
7
7
100Ω
100Ω
6
6
3
DE
3
DE
A 1
2 B
1/4 LTC1518
RECEIVER
OUTPUT
4
EN
EN
LTC1685
LTC1685
12
3
RO
1685 F10b
20ns/DIV
1685 F11b
Figure 11b. 100ft of Category 5 UTP: 20ns Pulse
Figure 10
9
LTC1685
APPLICATIONS INFORMATION
U
W U U
DRIVER
INPUT
2V/DIV
CABLE DELAY
DRIVER
INPUT
2V/DIV
RECEIVER
INPUT
1V/DIV
5V/DIV
RECEIVER
OUTPUT
2V/DIV
RECEIVER
OUTPUT
1µs/DIV
100ns/DIV
1685 F14a
1685 F12
Figure 12. 1000ft of Category 5 UTP: 4Mbps
Figure 14a. 4000ft of Category 5 UTP: 1µs Pulse
DRIVER INPUT
2V/DIV
DRIVER
INPUT
2V/DIV
5V/DIV
DIFFERENTIAL
RECEIVER
INPUT
2V/DIV
2V/DIV
RECEIVER
OUTPUT
RECEIVER
OUTPUT
20ns/DIV
1µs/DIV
1685 F13
1685 F14b
Figure 13. 100ft of Telephone Grade UTP: 30Mbps
Figure 14b. 4000ft of Category 5 UTP: 1Mbps Square Wave
Very inexpensive unshielded telephone grade twisted pair
is shown in Figure 13. In spite of the noticeable loss at the
receiver input, the LTC1685 can still transfer 30Mbps at
100ft of telephone grade UTP. Note that under all these
conditions, the LTC1685 can pass through a single data
pulse equal to the inverse of the data rate (e.g., 20ns for
50Mbps data rate).
High Speed Backplane Transmission
TheLTC1685canalsobeusedinbackplanepoint-to-point
transceiver applications, where the user wants to assure
operation even when the common mode goes above or
below the rails. It is advisable to terminate the PC traces
when approaching maximum speeds. Since the LTC1685
is not intended to drive parallel terminated cables with
characteristic impedances much less than that of twisted
pair, both ends of the PC trace must be series terminated
with the characteristic impedance of the trace. For best
results, the signal should be routed differentially. The true
andcomplementoutputsoftheLTC1685shouldberouted
on adjacent layers of the PC board. The two traces should
be routed very symmetrically, minimizing and equalizing
parasitics to nearby signal and power/ground layers. For
single-ended transmission, route the series terminated
Even at distances of 4000ft, 1Mbps data rates are possible
using the LTC1685 and category 5 UTP. Figure 14a shows
a 1µs pulse propagated down 4000ft of category 5 UTP.
Notice both the DC and the AC losses at the receiver input.
The DC attenuation is due to the parasitic resistance of the
cable. Figure 14b shows a 1Mbps square wave over
4000ft. To transmit at this speed but using longer cable
lengths, see the LTC1686/LTC1687 high speed RS485
full-duplex transceivers.
10
LTC1685
U
W U U
APPLICATIONS INFORMATION
RE TERM POWER
2
TERM POWER RE
single-ended trace over an adjacent ground plane. Then
setthe(bypassed)negativeinputofthereceivertoroughly
2.5V. Note that single-ended operation might not reach
maximum speeds.
2
1
4
1
4
RO
DI
RO
DI
330Ω
330Ω
150Ω
122Ω CABLE
7
7
150Ω
6
3
6
3
High Speed Differential SCSI (Fast-20, Fast-40 HVD)
A 1
2 B
DE
DE
330Ω
330Ω
4
EN
EN
LTC1685
1/4 LTC1518
LTC1685
The LTC1685’s high speed, tight propagation delay win-
dowandmatcheddriver/receiverpropagationdelaysmake
it a natural choice as the external transceiver in high speed
differential SCSI applications. Note that the ±3.5ns propa-
gation delay window covers the entire commercial tem-
perature range. If, for example, a group of 16 transceivers
is placed on the same board, their temperature difference
will be much smaller. Hence, the difference in their propa-
gation delays should be even better than the ±3.5ns
specification (typically better than ±2ns). The LTC1685 is
the most efficient and reliable implementation that meets
the Fast-20 and Fast-40 HVD driver and receiver skew
specifications.
12
3
RO
1685 F15
Figure 15. Fast-20, Fast-40 Differential SCSI Application
margin. Furthermore, the good high frequency CMRR of
the receiver will serve to reject any common mode
interference.
DE, DI Inputs
It is not necessary that the driver input (DI) have 0V to 3V
signal levels. The DI input can be driven by CMOS levels
(0V to 5V) and still achieve 40Mbps operation. However,
duty cycle will be slightly compromised when driven by a
CMOS device. Care should be taken to minimize the
ringing on the DI input in order to achieve a driver
propagation delay within the ±3.5ns window. This also
improves the package-to-package matching of propaga-
tion delays.
Power-Up Requirements
The LTC1685 has unique short-circuit protection that
shutsoffthebigoutputdevices(andkeepsthemoff)when
a short is detected. When the LTC1685 is powered up with
the driver outputs enabled (Figure 15 shows a typical
connection), the part will power up in short-circuit mode.
After power-up, the user must hold the DE pin of the
LTC1685 low for at least 200ns in order to start normal
operation. Note also that turning the termination power
on/off might induce the LTC1685 to see a “short.” Conse-
quently, the DE pin should be held low for 200ns after
cable termination power is turned on.
The DE pin should be held low for 200ns after the power-
up sequence has been completed. After fault conditions
such as an output short or thermal shutdown, the DE pin
should be held low for at least 200ns after the fault has
been removed. This is usually necessary only if the driver
outputs are connected to DC-biased cable terminations
(as in Figure 15).
This requirement is solely due to the cable termination
(the165Ωparallelresistancetobothpowerandground).
For applications whose connections to the cable are
made exclusively with RS485 devices, the cable can be
terminated only across the two signal wires (as in Figure
10). With cable distances covering under 25 meters, the
common mode range of the LTC1685 should be more
than sufficient to account for any ground differences
between any two communicating devices. The fact that
transmission is differential should greatly improve noise
Layout Considerations
A ground plane is recommended when using a high
frequency device like the LTC1685. A 0.1µF ceramic by-
pass capacitor less than 1/4 inch away from the VDD pin is
recommended.Goodbypassingisespeciallyneededwhen
operating at maximum frequency or when package-to-
package matching is very important. The PC board traces
connected to the “A” and “B” outputs must be kept as
symmetrical and short as possible to obtain the same
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC1685
U
W U U
APPLICATIONS INFORMATION
parasitic board capacitance. This maintains the good
matching characteristics of the low-to-high and high-to-
low transitions of the LTC1685. Note that output “A” to
output“B”capacitanceshouldalsobeminimized.Ifrouted
adjacent to each other on the same layer, they should be
separated by an amount at least as wide as the trace
widths. Ifoutput“A”andoutput“B”areroutedondifferent
signal planes, they should not be routed directly on top of
each other. A trace width’s lateral separation is also
recommended.
As mentioned before, care should also be taken when
routing the “DI” input. To achieve consistent board-to-
board propagation delay, the ringing on this signal should
be kept below a few hundred millivolts.
U
PACKAGE DESCRIPTION
Dimensions in inches (millimeters) unless otherwise noted.
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
7
5
8
6
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
3
4
2
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0°– 8° TYP
0.016 – 0.050
0.406 – 1.270
0.050
(1.270)
BSC
0.014 – 0.019
(0.355 – 0.483)
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
SO8 0695
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1485
High Speed RS485 Transceiver
High Speed Quad RS485 Receivers
High Speed Quad Differential Receiver
High Speed RS485 Driver/Receiver
High Speed Quad RS485 Drivers
10Mbps, Pin Compatible with LTC485
LTC1518/LTC1519
LTC1520
52Mbps, Pin Compatible with LTC488/LTC489
52Mbps, ±100mV Threshold, Rail-to-Rail Common Mode
52Mbps, Pin Compatible with LTC490/LTC491
100Mbps, Pin Compatible with LTC486/LTC487
LTC1686/LTC1687
LTC1688/LTC1689
1685fa LT/LCG 0700 2K REV A • PRINTED IN THE USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
12
●
●
(408)432-1900 FAX:(408)434-0507 www.linear-tech.com
LINEAR TECHNOLOGY CORPORATION 1997
相关型号：
LTC1685IS8#TRPBF
LTC1685 - 52Mbps, Precision Delay, RS485 Fail-Safe Transceiver; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C
Linear
LTC1686CS8#PBF
LTC1686 - 52Mbps Precision Delay RS485 Fail-Safe Transceivers; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC1686CS8#TRPBF
LTC1686 - 52Mbps Precision Delay RS485 Fail-Safe Transceivers; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LTC1686IS8#TR
LTC1686 - 52Mbps Precision Delay RS485 Fail-Safe Transceivers; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C
Linear
LTC1687CS#PBF
LTC1687 - 52Mbps Precision Delay RS485 Fail-Safe Transceivers; Package: SO; Pins: 14; Temperature Range: 0°C to 70°C
Linear
LTC1687IS
LTC1687 - 52Mbps Precision Delay RS485 Fail-Safe Transceivers; Package: SO; Pins: 14; Temperature Range: -40°C to 85°C
Linear
©2020 ICPDF网 联系我们和版权申明