LTC1734ES6-4.2#TRPBF [Linear]
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C;型号: | LTC1734ES6-4.2#TRPBF |
厂家: | Linear |
描述: | LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C 电池 光电二极管 |
文件: | 总12页 (文件大小:184K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC1734
Lithium-Ion Linear
Battery Charger in ThinSOT
U
FEATURES
DESCRIPTIO
Low Profile (1mm) ThinSOTTM Package
The LTC®1734 is a low cost, single cell, constant-current/
constant-voltage Li-Ion battery charger controller. When
combined with a few external components, the SOT-23
packageformsaverysmall,lowcostchargerforsinglecell
lithium-ion batteries.
■
■
No Blocking Diode Required
■
No Sense Resistor Required
■
1% Accurate Preset Voltages: 4.1V or 4.2V
■
Charge Current Monitor Output
for Charge Termination
The LTC1734 is available in 4.1V and 4.2V versions with
1% accuracy. Constant current is programmed using a
singleexternalresistorbetweenthePROGpinandground.
Manual shutdown is accomplished by floating the pro-
gram resistor while removing input power automatically
puts the LTC1734 into a sleep mode. Both the shutdown
and sleep modes drain near zero current from the battery.
■
Programmable Charge Current: 200mA to 700mA
■
Automatic Sleep Mode with Input Supply Removal
■
Manual Shutdown
■
Negligible Battery Drain Current in Shutdown
■
Undervoltage Lockout
■
Self Protection for Overcurrent/Overtemperature
U
Charge current can be monitored via the voltage on the
PROG pin allowing a microcontroller or ADC to read the
currentanddeterminewhentoterminatethechargecycle.
The output driver is both current limited and thermally
protected to prevent the LTC1734 from operating outside
of safe limits. No external blocking diode is required.
APPLICATIO S
■
Cellular Telephones
Handheld Computers
■
■
Digital Cameras
■
Charging Docks and Cradles
■
Low Cost and Small Size Chargers
The LTC1734 can also function as a general purpose
current source or as a current source for charging nickel-
cadmium (NiCd) and nickel-metal-hydride (NiMH) batter-
ies using external termination.
■
Programmable Current Sources
, LTC and LT are registered trademarks of Linear Technology Corporation.
ThinSOT is a trademark of Linear Technology Corporation.
U
TYPICAL APPLICATIO
PROG Pin Indicates Charge Status
5V
V
BAT
300mA Li-Ion Battery Charger
4V
3V
3
2
1
6
5
V
IN
V
I
SENSE
CC
5V
LTC1734
1µF
FMMT549
= 300mA
GND
DRIVE
CONSTANT
CURRENT
CONSTANT
VOLTAGE
I
2V
BAT
4
PROG
BAT
1.5V
V
PROG
SINGLE
+
10µF
Li-Ion
R
PROG
1V
BATTERY
5k
1734 TA01
0V
CHARGING
BEGINS
CHARGING
COMPLETE
1734 TA01b
1
LTC1734
W W U W
U
W U
ABSOLUTE MAXIMUM RATINGS
PACKAGE/ORDER INFORMATION
(Note 1)
Supply Voltage (VCC) ...................................–0.3V to 9V
Input Voltage (BAT, PROG) ........ –0.3V to (VCC + 0.3V)
Output Voltage (DRIVE) .............. –0.3V to (VCC + 0.3V)
Output Current (ISENSE) ................................... –900mA
Short-Circuit Duration (DRIVE) ...................... Indefinite
Junction Temperature.......................................... 125°C
Operating Ambient Temperature Range
ORDER PART
NUMBER
TOP VIEW
LTC1734ES6-4.1
LTC1734ES6-4.2
I
1
6 DRIVE
5 BAT
SENSE
GND 2
V
CC
3
4 PROG
S6 PACKAGE
6-LEAD PLASTIC SOT-23
S6 PART MARKING
(Note 2) ...............................................–40°C to 85°C
Operating Junction Temperature (Note 2) ............ 100°C
Storage Temperature Range ................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
LTHD
LTRG
TJMAX = 125°C, θJA = 230°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 5V, GND = 0V and VBAT is equal to the float voltage unless
otherwise noted. All current into a pin is positive and current out of a pin is negative. All voltages are referenced to GND, unless
otherwise specified.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Supply
CC
V
Operating Supply Range (Note 5)
Quiescent V Pin Supply Current
●
●
4.55
8
V
CC
I
V
BAT
= 5V, (Forces I
= I = 0),
BAT
670
1150
µA
CC
CC
DRIVE
I
= 200µA,(7500Ω from PROG to GND)
PROG
I
I
V
Pin Supply Current in Manual Shutdown
CC
PROG Pin Open
PROG Pin Open
●
●
450
0
900
1
µA
µA
SHDN
BMS
Battery Drain Current in Manual Shutdown
(Note 3)
–1
I
Battery Drain Current in Sleep Mode (Note 4)
Undervoltage Lockout Exit Threshold
Undervoltage Lockout Entry Threshold
Undervoltage Lockout Hysteresis
V
CC
V
CC
V
CC
V
CC
= 0V
●
●
●
–1
0
1
µA
V
BSL
V
V
V
Increasing
Decreasing
Decreasing
4.45
4.30
4.56
4.41
150
4.68
4.53
UVLOI
UVLOD
UVHYS
V
mV
Charging Performance
V
Output Float Voltage in Constant Voltage Mode 4.1V Version, I
4.2V Version, I
= 10mA, 4.55V ≤ V ≤ 8V
●
●
4.059 4.10
4.158 4.20
4.141
4.242
V
V
BAT
BAT1
BAT2
BAT
BAT
CC
= 10mA, 4.55V ≤ V ≤ 8V
CC
I
I
Output Full-Scale Current When Programmed
for 200mA in Constant Current Mode
R
= 7500Ω, 4.55V ≤ V ≤ 8V,
●
155
200
240
770
0.28
mA
mA
V
PROG
CC
Pass PNP Beta > 50
Output Full-Scale Current When Programmed
for 700mA in Constant Current Mode
R
PROG
= 2143Ω, 4.55V ≤ V ≤ 8V,
●
620
700
CC
Pass PNP Beta > 50
= 10% of I , R = 7500Ω,
BAT1 PROG
V
V
Current Monitor Voltage on PROG Pin
Current Monitor Voltage on PROG Pin
Drive Output Current
I
0.045 0.15
CM1
CM2
BAT
4.55V ≤ V ≤ 8V, Pass PNP Beta > 50,
0°C ≤ T ≤ 85°C
CC
A
I
= 10% of I
, R = 2143Ω,
BAT2 PROG
0.10
30
0.15
0.20
V
BAT
4.55V ≤ V ≤ 8V, Pass PNP Beta > 50,
0°C ≤ T ≤ 85°C
CC
A
I
V
DRIVE
= 3.5V
●
mA
DSINK
2
LTC1734
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 5V, GND = 0V and VBAT is equal to the float voltage unless
otherwise noted. All current into a pin is positive and current out of a pin is negative. All voltages are referenced to GND, unless
otherwise specified.
SYMBOL PARAMETER
Charger Manual Control
CONDITIONS
MIN
2.05
–6
TYP
MAX
2.25
–1.5
130
UNITS
V
V
Manual Shutdown Threshold
Manual Shutdown Hysteresis
Programming Pin Pull-Up Current
V
PROG
V
PROG
V
PROG
Increasing
●
●
2.15
90
V
mV
µA
MSDT
Decreasing from V
= 2.5V
MSHYS
PROGPU
MSDT
I
–3
Protection
I
Drive Output Short-Circuit Current Limit
V
DRIVE
= V
CC
35
65
mA
DSHRT
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 4: Assumes that the external PNP pass transistor has negligible B-E
reverse-leakage current when the emitter is biased at 0V (V ) and the
CC
base is biased at 4.2V (V ).
Note 5: The 4.68V maximum undervoltage lockout (UVLO) exit threshold
must first be exceeded before the minimum V specification applies.
Short duration drops below the minimum V specification of several
BAT
Note 2: The LTC1734E is guaranteed to meet performance specifications
from 0°C to 70°C ambient temperature range and 0°C to 100°C junction
temperature range. Specifications over the –40°C to 85°C operating
ambient temperature range are assured by design, characterization and
correlation with statistical process controls.
CC
CC
microseconds or less are ignored by the UVLO. If manual shutdown is
entered, then V must be higher than the 4.68V maximum UVLO
threshold before manual shutdown can be exited. When operating near the
CC
Note 3: Assumes that the external PNP pass transistor has negligible B-C
reverse-leakage current when the collector is biased at 4.2V (V ) and the
BAT
minimum V , a suitable PNP transistor with a low saturation voltage
base is biased at 5V (V ).
CC
CC
must be used.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Float Voltage vs Temperature
and Supply Voltage
IBAT1 vs Temperature
and Supply Voltage
Float Voltage vs IBAT
4.21
4.20
4.19
4.201
4.200
4.199
210
200
190
I
= 10mA
V
A
= 5V
R
= 7.5k
BAT
CC
PROG
PNP = FCX589
PNP = FCX589
4.2V OPTION
T
= 25°C
PNP = FCX589
4.2V OPTION
R
= 2150Ω
PROG
V
CC
= 4.55V AND 8V
V
= 8V
CC
V
= 4.55V
25
CC
–50
0
50
75 100 125
–25
400
(mA)
700
50
TEMPERATURE (°C)
125
0
200 300
500 600
–50
0
25
75 100
100
–25
TEMPERATURE (°C)
I
BAT
1734 G01
1734 G02
1734 G03
3
LTC1734
U W
TYPICAL PERFOR A CE CHARACTERISTICS
IBAT2 vs Temperature
and Supply Voltage
IBAT1 vs VBAT
IBAT2 vs VBAT
740
700
660
210
200
190
750
700
650
V
T
= 5V
R
= 2.15k
V
T
= 5V
CC
CC
A
R
PROG
= 25°C
PNP = FCX589
= 25°C
A
= 7.5k
R
= 2.15k
PROG
PROG
PNP = FCX589
PNP = FCX589
BAT PIN MUST BE DISCONNECTED
AND GROUNDED TO FORCE
CC MODE IN THIS REGION
BAT PIN MUST BE DISCONNECTED
AND GROUNDED TO FORCE
CC MODE IN THIS REGION
V
CC
= 4.55V AND 8V
–50
0
25
50
75 100 125
0
1
2
3
4
5
0
1
3
4
–25
2
5
TEMPERATURE (°C)
V
(V)
V
BAT
(V)
BAT
1734 G04
1734 G05
1734 G06
Program Pin Pull-Up Current vs
Temperature and Supply Voltage
Program Pin Pull-Up Current
vs VPROG
Program Pin Voltage
vs Charge Current (200mA)
3.6
3.4
3.2
3.0
3.6
3.5
3.4
3.3
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
V
A
R
= 5V
CC
V
T
= 8V
V
PROG
= 2.5V
CC
A
T
= 25°C
= 25°C
= 7.5k
PROG
PNP = FCX589
V
CC
= 8V
V
CC
= 4.55V
3.2
3.1
3.0
LIMITS AT 25mV DUE TO
PROGRAMMING PIN PULL-UP
2.8
2.6
CURRENT (I
)
PROGPU
2
4
5
6
7
8
3
50
TEMPERATURE (°C)
100 125
100
–50 –25
0
25
75
0
50
150
200
V
PROG
(V)
I
(mA)
BAT1
1635 G08
1734 G07
1734 F09
Program Pin Voltage for IBAT1/10
vs Temperature and Supply Voltage
Program Pin Voltage for IBAT2/10
vs Temperature and Supply Voltage
Program Pin Voltage
vs Charge Current (700mA)
160
150
140
160
150
140
1.6
V
T
= 5V
R
= 7.5k
R
= 2.15k
CC
A
R
PROG
PROG
PNP = FCX589
= 25°C
PNP = FCX589
1.4
1.2
= 2.15k
PROG
PNP = FCX589
1.0
0.8
0.6
0.4
0.2
V
= 8V
CC
V
= 8V
CC
V
= 4.55V
CC
V
= 4.55V
CC
LIMITS AT 6mV DUE TO
PROGRAMMING PIN PULL-UP
CURRENT (I
)
PROGPU
0
100 200
400 500 600 700
0
300
50
75 100
TEMPERATURE (°C)
125
50
TEMPERATURE (°C)
125
–50
0
25
–50
0
25
75 100
–25
–25
I
(mA)
BAT2
1734 G10
1734 G11
1734 G12
4
LTC1734
U
U
U
PIN FUNCTIONS
ISENSE (Pin 1): Sense Node for Charge Current. Current
from VCC passes through the internal current sense resis-
tor and reappears at ISENSE to supply current to the
external PNP emitter. The PNP collector provides charge
current to the battery.
(IBAT = 1500/RPROG). This pin also allows for the charge
current to be monitored. The voltage on this pin is propor-
tionaltothechargecurrentwhere1.5Vcorrespondstothe
full programmed currrent. Floating this pin allows an
internal current source to pull the pin voltage above the
shutdownthresholdvoltage. Becausethispinisinasignal
path, excessive capacitive loading can cause AC instabil-
ity. See the Applications Information section for more
details.
GND(Pin2):Ground. Providesareferencefortheinternal
voltage regulator and a return for all internal circuits.
When in the constant voltage mode, the LTC1734 will
precisely regulate the voltage between the BAT and GND
pins. The battery ground should connect close to the GND
pin to avoid voltage drop errors.
BAT (Pin 5): Battery Voltage Sense Input. A precision
internal resistor divider sets the final float voltage on this
pin. This divider is disconnected in the manual shutdown
or sleep mode. When charging, approximately 34µA
flows into the BAT pin. To minimize float voltage errors,
avoid excessive resistance between the battery and the
BATpin. Fordynamicallystableoperation, thispinusually
requires a minimum bypass capacitance to ground of 5µF
tofrequencycompensateforthehighfrequencyinductive
effects of the battery and wiring.
VCC (Pin 3): Positive Input Supply Voltage. This pin
supplies power to the internal control circuitry and exter-
nal PNP transistor through the internal current sense
resistor. This pin should be bypassed to ground with a
capacitor in the range of 1µF to 10µF.
PROG (Pin 4): Charge Current Programming, Charge
Current Monitor and Manual Shutdown Pin. Provides a
virtual reference voltage of 1.5V for an external resistor
(RPROG) tied between this pin and ground that programs
the battery charge current when the charger is in the
constant current mode. The typical charge current will be
1000 times greater than the current through this resistor
DRIVE (Pin 6): Base Drive Output for the External PNP
Pass Transistor. Provides a controlled sink current that
drives the base of the PNP. This pin has current limiting
protection for the LTC1734.
W
V
IN
BLOCK DIAGRA
1µF
V
CC
3
I
I
/1000
BAT
60Ω
0.06Ω
BAT
I
SENSE
1
6
SHUTDOWN
VOLTAGE
REFERENCE
2.5V
REF
+
–
DRIVE
OUTPUT
DRIVER
A3
UVLO
C1
SHUTDOWN
SHUTDOWN
TEMPERATURE AND
CURRENT LIMITING
I
BAT
BAT
2.15V
1.5V
2.5V
5
+
+
+
SINGLE
Li-Ion
CELL
10µF
A2
A1
–
–
–
3µA
SHUTDOWN
1734 BD
4
2
GND
PROG
R
PROG
5
LTC1734
U
OPERATIO
TheLTC1734isalinearbatterychargercontroller. Opera-
tion can best be understood by referring to the Block
Diagram. Charging begins when VCC rises above the
UVLO (Undervoltage Lockout) threshold VUVLOI and an
external current programming resistor is connected be-
tween the PROG pin and ground. When charging, the
collector of the external PNP provides the charge current.
The PNP’s emitter current flows through the ISENSE pin
and through the internal 0.06Ω current sense resistor.
This current is close in magnitude, but slightly more than
the collector current since it includes the base current.
Amplifier A3, along with the P-channel FET, will force the
same voltage that appears across the 0.06Ω resistor to
appear across the internal 60Ω resistor. The scale factor
of 1000:1 in resistor values will cause the FET’s drain
current to be 1/1000 of the charge current and it is this
current that flows through the PROG pin. In the constant
current mode, amplifier A2 is used to limit the charge
4.2V (2.5V at amplifier A1’s input) the amplifier will divert
current away from the output driver thus limiting charge
currenttothatwhichwillmaintain4.2Vonthebattery.This
is the constant voltage mode.
When in the constant voltage mode, the 1000:1 current
ratio is still valid and the voltage on the PROG pin will
indicate the charge current as a proportion of the maxi-
mum current set by the current programming resistor.
Thebatterychargecurrentis1000•(VPROG/RPROG)amps.
This feature allows a microcontroller with an ADC to easily
monitorchargecurrentandifdesired,manuallyshutdown
the charger at the appropriate time.
When VCC is applied, the charger can be manually shut
down by floating the otherwise grounded end of RPROG
.
An internal 3µA current source pulls the PROG pin above
the 2.15V threshold of voltage comparator C1 initiating
shutdown.
current to the maximum that is programmed by RPROG
.
For charging NiMH or NiCd batteries, the LTC1734 can
function as a constant current source by grounding the
BAT pin. This will prevent amplifier A1 from trying to limit
charging current and only A2 will control the current.
The PROG pin current, which is 1/1000 of the charge
current, develops a voltage across the program resistor.
When this voltage reaches 1.5V, amplifier A2 begins
diverting current away from the output driver, thus limit-
ing the charge current. This is the constant current mode.
The constant charge current is 1000 • (1.5V/RPROG).
Fault conditions such as overheating of the die or exces-
sive DRIVE pin current are monitored and limited.
When input power is removed or manual shutdown is
entered, the charger will drain only tiny leakage currents
from the battery, thus maximizing battery standby time.
WithVCC removedtheexternalPNP’sbaseisconnectedto
the battery by the charger. In manual shutdown the base
is connected to VCC by the charger.
As the battery accepts charge, its voltage rises. When it
reaches the preset float voltage of 4.2V (LTC1734-4.2
version), a precisely divided down version of this voltage
(2.5V) is compared to the 2.5V internal reference voltage
by amplifier A1. If the battery voltage attempts to exceed
W U U
U
APPLICATIO S I FOR ATIO
Charging Operation
charge current begins to decrease and the constant
voltage portion of the charge cycle begins. The charge
current will continue to decrease exponentially as the
battery approaches a fully charged condition.
Charging begins when an input voltage is present that
exceeds the undervoltage lockout threshold (VUVLOI), a
Li-Ion battery is connected to the charger output and a
program resistor is connected from the PROG pin to
ground. During the first portion of the charge cycle, when
the battery voltage is below the preset float voltage, the
charger is in the constant current mode. As the battery
voltage rises and reaches the preset float voltage, the
Should the battery be removed during charging, a fast
built-inprotectioncircuitwillpreventtheBATpinfromris-
ing above 5V, allowing the precision constant voltage
circuit time to respond.
6
LTC1734
U
W U U
APPLICATIONS INFORMATION
Manual Shutdown
entering shutdown, but no more than 0.3V above VCC to
prevent damaging the LTC1734 from excessive PROG
pin current. An exception is if VCC is allowed to float with
no other circuitry loading VCC down. Then, because the
current will be low, it is allowable to have the PROG pin
shutdown voltage applied. A three-state logic driver with
sufficient pull-up current can be used to perform this
function by enabling the high impedance state to charge
or enabling the pull-up device to enter shutdown.
Floating the program resistor allows an internal 3µA
current source (IPROGPU) to pull the PROG pin above the
2.15V shutdown threshold (VMSDT), thus shutting down
the charger. In this mode, the LTC1734 continues to draw
some current from the supply (ISHDN), but only a negli-
gible leakage current is delivered to the battery (IBMS).
Shutdown can also be accomplished by pulling the other-
wise grounded end of the program resistor to a voltage
greaterthan2.25V(VMSDTMax).Chargingwillceaseabove
1.5V, but the internal battery voltage resistor divider will
draw about 34µA from the battery until shutdown is
entered. Figure 1 illustrates a microcontroller configura-
tion that can either float the resistor or force it to a voltage.
The voltage should be no more than 8V when high and
have an impedance to ground of less than 10% of the
program resistor value when low to prevent excessive
charge current errors. To reduce errors the program
resistor value may be adjusted to account for the imped-
ance to ground. The programming resistor will prevent
potentially damaging currents if the PROG pin is forced
above VCC. Under this condition VCC may float, be loaded
down by other circuitry or be shorted to ground. If VCC is
not shorted to ground the current through the resistor will
pull VCC up somewhat.
An NPN transistor or a diode can also be utilized to
implement shutdown from a voltage source. These have
theadvantageofblockingcurrentwhenthevoltagesource
goes low, thus automatically disconnecting the voltage
source for normal charging operation. The use of an NPN
allows for use of a weak voltage source due to the current
gain of the transistor. For an NPN connect the collector to
VCC, the base to the voltage source and the emitter to the
PROG pin. For a diode, connect the anode to the voltage
source and cathode to the PROG pin. An input high level
ranging from 3.3V to VCC should be adequate to enter
shutdown while a low level of 0.5V or less should allow for
normal charging operation. Use of inexpensive small
signal devices such as the 2N3904 or 1N914 is recom-
mended to prevent excessive capacitive loading on the
PROG pin (see Stability section).
Another method is to directly switch the PROG pin to a
voltage source when shutdown is desired (Caution: pull-
ing the PROG below 1.5V with VCC applied will cause
excessive and uncontrolled charge currents). The volt-
age source must be capable of sourcing the resulting
current through the program resistor. This has the ad-
vantage of not adding any error to the program resistor
during normal operation. The voltage on the PROG pin
must be greater than 2.25V (VMSDT(MAX)) to ensure
Sleep Mode
When the input supply is disconnected, the IC enters the
sleep mode. In this mode, the battery drain current (IBSL
is a negligible leakage current, allowing the battery to re-
main connected to the charger for an extended period of
time without discharging the battery. The leakage current
is due to the reverse-biased B-E junction of the external
PNP transistor.
)
Undervoltage Lockout
R
PROG
PROG
LTC1734
OPEN DRAIN
OR TOTEM
Undervoltage lockout (UVLO) keeps the charger off until
the input voltage exceeds a predetermined threshold level
(VUVLOI) that is typically 4.56V. Approximately 150mV of
hysteresis is built in to prevent oscillation around the
threshold level. In undervoltage lockout, battery drain
current is very low (<1µA).
POLE OUTPUT
µC
ADC INPUT
1734 F01
Figure 1. Interfacing with a Microcontroller
7
LTC1734
U
W U U
APPLICATIONS INFORMATION
Programming Constant Current
monitoring accuracy can degrade considerably at very
low current levels. If current monitoring is desired, a
minimum full-scale current of 200mA is recommended.
When in the constant current mode, the full-scale charge
current(C)isprogrammedusingasingleexternalresistor
between the PROG pin and ground. This charge current
will be 1000 times greater than the current through the
program resistor. The program resistor value is selected
by dividing the voltage forced across the resistor (1.5V)
by the desired resistor current.
Different charge currents can be programmed by various
meanssuchasbyswitchingindifferentprogramresistors
as shown in Figures 2 and 3. A voltage DAC connected
through a resistor to the PROG pin or a current DAC
connected in parallel with a resistor to the PROG pin can
also be used to program current (the resistor is required
with the IDAC to maintain AC stability as discussed in the
Stability section). Another means is to use a PWM output
from a microcontroller to duty cycle the charger into and
out of shutdown to create an average current (see Manual
Shutdown section for interfacing examples). Because
chargers are generally slow to respond, it can take up to
approximately 300µs for the charger to fully settle after a
shutdown is deasserted. This delay must be accounted for
unless the minimum PWM low duration is about 3ms or
more. Shutdown occurs within a few microseconds of a
shutdown command. The use of PWM can extend the
average current to less than the normal 200mA minimum
constant current.
The LTC1734 is designed for a maximum current of
approximately 700mA. This translates to a maximum
PROG pin current of 700µA and a minimum program
resistorofapproximately2.1k. BecausethePROGpinisin
a closed-loop signal path, the pole frequency must be kept
high enough to maintain adequate AC stability by avoiding
excessive capacitance on the pin. See the Stability section
for more details.
The minimum full-scale current that can be reliably pro-
grammed is approximately 50mA, which requires a pro-
gram resistor of 30k. Limiting capacitive loading on the
program pin becomes more important when high value
program resistors are used. In addition, the current
3
2
4
1
V
IN
CHARGE CURRENT CONTROL 1 CONTROL 2
V
I
SENSE
CC
5V
0
LOW
LOW
HIGH
HIGH
LOW
HIGH
LOW
HIGH
LTC1734
1µF
200mA
500mA
700mA
6
5
FZT549
GND
DRIVE
OPTIONAL FILTER
1k
I
BAT
CHARGE
CURRENT
MONITOR
(FILTERED)
CHARGE
CURRENT
PIN 4
PROG
BAT
SINGLE
MONITOR
0.1µF TO
0.5µF
10µF
Li-Ion
(UNFILTERED)
3k
7.5k
Q2
BATTERY
Q1
2N7002
1734 F02
2N7002
CONTROL 1
CONTROL 2
Figure 2. Logic Control Programming of Output Current to 0mA, 200mA, 500mA or 700mA
3
2
4
1
6
5
V
IN
V
I
SENSE
CC
5V
LTC1734
1µF
FZT549*
GND
DRIVE
CURRENT CONTROL 1 CONTROL 2
I
LOAD
PROG
BAT
0
LOW
LOW
HIGH
HIGH
LOW
HIGH
LOW
HIGH
200mA
500mA
700mA
LOAD
3k
7.5k
Q2
1734 F03
Q1
2N7002
2N7002
*OBSERVE MAXIMUM TEMPERATURE
CONTROL 1
CONTROL 2
Figure 3. Programmable Current Source with Output Current of 0mA, 200mA, 500mA or 700mA
8
LTC1734
U
W U U
APPLICATIONS INFORMATION
Monitoring Charge Current
used, more base current is required from the LTC1734.
This can result in the output drive current limit being
reached, or thermal shutdown due to excessive power
dissipation. Excessive beta can affect AC stability (see
Stability section)
The voltage on the PROG pin indicates the charge current
as a proportion of the maximum current set by the
program resistor. The charge current is equal to 1000 •
(VPROG/RPROG) amps. This feature allows a microcontrol-
ler with an ADC to easily monitor charge current and if
desired, manually shut down the charger at the appropri-
atetime. SeeFigure1foranexample. TheminimumPROG
pin current is about 3µA (IPROGPU).
With low supply voltages, the PNP saturation voltage
(VCESAT) becomes important. The VCESAT must be less
than the minimum supply voltage minus the maximum
voltage drop across the internal sense resistor and bond
wires (0.1Ω) and battery float voltage. If the PNP transis-
tor can not achieve the low saturation voltage required,
base current will dramatically increase. This is to be
avoided for a number of reasons: output drive may reach
current limit resulting in the charger’s characteristics to
gooutofspecifications, excessivepowerdissipationmay
force the IC into thermal shutdown, or the battery could
becomedischargedbecausesomeofthecurrentfromthe
DRIVE pin could be pulled from the battery through the
forward biased collector base junction.
Errors in the charge current monitor voltage on the PROG
pinareinverselyproportionaltobatterycurrentandcanbe
statistically approximated as follows:
One Sigma Error(%) 1 + 0.3/IBAT(A)
Dynamic loads on the battery will cause transients to
appear on the PROG pin. Should they cause excessive
errors in charge current monitoring, a simple RC filter as
shown in Figure 2 can be used to filter the transients. The
filter will also quiet the PROG pin to help prevent inadvert-
ent momentary entry into the manual shutdown mode.
For example, to program a charge current of 500mA with
a minimum supply voltage of 4.75V, the minimum operat-
ing VCE is:
Because the PROG pin is in a closed-loop signal path the
pole frequency must be kept high enough to maintain
adequate AC stability. This means that the maximum
resistance and capacitance presented to the PROG pin
must be limited. See the Stability section for more details.
VCE(MIN)(V) = 4.75 – (0.5)(0.1) – 4.2 = 0.5V
The actual battery charge current (IBAT) is slightly smaller
than the expected charge current because the charger
senses the emitter current and the battery charge current
will be reduced by the base current. In terms of β (IC/IB),
IBAT can be calculated as follows:
Constant Current Source
The LTC1734 can be used as a constant current source by
disabling the voltage control loop as shown in Figure 3.
This is done by pulling the BAT pin below the preset float
voltages of 4.1V or 4.2V by grounding the BAT pin. The
program resistor will determine the output current. The
outputcurrentrangecanbebetweenapproximately50mA
and 700mA, depending on the maximum power rating of
the external PNP pass transistor.
IBAT(A) = 1000 • IPROG[β/(β + 1)]
If β = 50, then IBAT is 2% low. If desired, the 2% loss can
be compensated for by increasing IPROG by 2%.
Another important factor to consider when choosing the
PNP pass transistor is the power handling capability. The
transistor’sdatasheetwillusuallygivethemaximumrated
power dissipation at a given ambient temperature with a
power derating for elevated temperature operation. The
maximum power dissipation of the PNP when charging is:
External PNP Transistor
The external PNP pass transistor must have adequate
beta, lowsaturationvoltageandsufficientpowerdissipa-
tion capability (including any heat sinking, if required).
P
D(MAX)(W) = IBAT (VDD(MAX) – VBAT(MIN))
VDD(MAX) is the maximum supply voltage and VBAT(MIN) is
the minimum battery voltage when discharged.
To provide 700mA of charge current with the minimum
available base drive of approximately 30mA requires a
PNPbetagreaterthan23. IflowerbetaPNPtransistorsare
9
LTC1734
U
W U U
APPLICATIONS INFORMATION
Table 1. PNP Pass Transistor Selection Guide
Maximum P (W)
D
Mounted on Board
at T = 25°C
Package Style
SOT-23
SOT-23
SOT-89
SOT-23-6
SOT-89
SOT-223
SOT-223
FTR
ZETEX Part Number
FMMT549
ROHM Part Number
Comments
Low V
A
0.5
0.625
1
CESAT
FMMT720
Very Low V
High Beta
CESAT,
FCX589 or BCX69
ZXT10P12DE6
FCX717
1.1
1 to 2
2
Very Low V
Very Low V
High Beta, Small
High Beta
CESAT,
CESAT,
FZT589
Low V
CESAT
2
BCP69 or FZT549
0.75
1
2SB822
2SB1443
2SA1797
2SB1182
Low V
Low V
Low V
Low V
CESAT
CESAT
CESAT
CESAT,
ATV
2
SOT-89
TO-252
10 (T = 25°C)
High Beta
C
Once the maximum power dissipation and VCE(MIN) are
known, Table 1 can be used as a guide in selecting some
PNPs to consider. In the table, very low VCESAT is less than
0.25V, low VCESAT is 0.25V to 0.5V and the others are 0.5V
to0.8Valldependingonthecurrent.Seethemanufacturer’s
data sheet for details. All of the PNP transistors are rated
to carry at least 1A continuously as long as the power
dissipationiswithinlimits.TheStabilitysectionaddresses
caution in the use of high beta PNPs.
constant voltage mode, a capacitor of at least 4.7µF is
usually required from BAT to ground. The battery and
interconnecting wires appear inductive at high frequen-
cies, and since these are in the feedback loop, this capaci-
tancemaybenecessarytocompensatefortheinductance.
This capacitor need not exceed 100µF and its ESR can
range from near zero to several ohms depending on the
inductance to be compensated. In general, compensation
is optimal with a capacitance of 4.7µF to 22µF and an ESR
of 0.5Ω to 1.5Ω.
Should overheating of the PNP transistor be a concern,
protection can be achieved with a positive temperature
coefficient (PTC) thermistor, wired in series with the
current programming resistor and thermally coupled to
the transistor. The PTH9C chip series from Murata has a
steep resistance increase at temperature thresholds from
85°C to 145°C making it behave somewhat like a thermo-
stat switch. For example, the model PTH9C16TBA471Q
thermistor is 470Ω at 25°C, but abruptly increase its
resistance to 4.7k at 125°C. Below 125°C, the device
exhibits a small negative TC. The 470Ω thermistor can be
added in series with a 1.6k resistor to form the current
programming resistor for a 700mA charger. Should the
thermistor reach 125°C, the charge current will drop to
238mA and inhibit any further increase in temperature.
Using high beta PNP transistors (>300) and very low ESR
output capacitors (especially ceramic) reduces the phase
margin, possibly resulting in oscillation. Also, using high
value capacitors with very low ESRs will reduce the phase
margin. Adding a resistor of 0.5Ω to 1.5Ω in series with
the capacitor will restore the phase margin.
In the constant current mode, the PROG pin is in the
feedback loop, not the battery. Because of this, capaci-
tance on this pin must be limited. Locating the program
resistor near the PROG pin and isolating the charge
current monitoring circuitry (if used) from the PROG pin
with a 1k to 10k resistor may be necessary if the capaci-
tance is greater than that given by the following equation:
400k
RPROG
CMAX(pF)
=
Stability
TheLTC1734containstwocontrolloops:constantvoltage
and constant current. To maintain good AC stability in the
10
LTC1734
U
W U U
APPLICATIONS INFORMATION
of instability due to any combination of extremely low ESR
values, high capacitance values of the output capacitor or
veryhighPNPtransistorbeta. Tominimizetheeffectofthe
scope probe capacitance, a 10k resistor is used to isolate
the probe from the program pin. Also, an adjustable load
resistor or current sink can be used to quickly alter the
charge current when a fully charged battery is used.
Higher charge currents require lower program resistor
values which can tolerate more capacitive loading on the
PROG pin. Maximum capacitance can be as high as 50pF
for a charge current of 200mA (RPROG = 7.5k).
Figure4isasimpletestcircuitforcheckingstabilityinboth
the constant current and constant voltage modes. With
input power applied and a near fully charged battery
connected to the charger, driving the PROG pin with a
pulse generator will cycle the charger in and out of the
manual shutdown mode. Referring to Figure 5, after a
short delay, the charger will enter the constant current
mode first, then if the battery voltage is near the pro-
grammed voltage of 4.1V or 4.2V, the constant voltage
mode will begin. The resulting waveform on the PROG pin
is an indication of stability.
Reverse Input Voltage Protection
In some applications, protection from reverse voltage on
VCC is desired. If the supply voltage is high enough, a
series blocking diode can be used. In other cases, where
the voltage drop must be kept low, a P-channel FET as
shown in Figure 6 can be used.
*
V
V
CC
IN
The double exposure photo in Figure 5 shows the effects
of capacitance on the program pin. The middle waveform
is typical while the lower waveform indicates excessive
program pin capacitance resulting in constant current
mode instability. Although not common, ringing on the
constant voltage portion of the waveform is an indication
LTC1734
1734 F06
*DRAIN-BULK DIODE OF FET
Figure 6. Low Loss Reverse Voltage Protection
VCC Bypass Capacitor
Many types of capacitors with values ranging from 1µF to
10µF located close to the LTC1734 will provide adequate
input bypassing. However, caution must be exercised
when using multilayer ceramic capacitors. Because of the
self resonant and high Q characteristics of some types of
ceramic capacitors, high voltage transients can be gener-
ated under some start-up conditions, such as connecting
the charger input to a hot power source. To prevent these
transients from exceeding the absolute maximum voltage
rating, several ohms of resistance can be added in series
with the ceramic input capacitor.
10k
TO SCOPE
PROG
BAT
+
6Ω TO
20Ω
R
PROG
3k
Li-Ion*
LTC1734
2.5V
0V
1734 F04
f = 1kHz
*FULLY CHARGED CELL
Figure 4. Setup for AC Stability Testing
5V
PULSE
GENERATOR
0V
Internal Protection
2V
1V
0V
2V
1V
0V
PROG PIN
(20pF ON PIN)
InternalprotectionisprovidedtopreventexcessiveDRIVE
pin currents (IDSHRT) and excessive self-heating of the
LTC1734 during a fault condition. The faults can be
generated from a shorted DRIVE pin or from excessive
DRIVE pin current to the base of the external PNP
transistor when it’s in deep saturation from too low a VCE.
This protection is not designed to prevent overheating of
theexternalpasstransistor.Indirectlythough,self-heating
of the PNP thermally conducting to the LTC1734 and
PROG PIN
(200pF ON PIN)
SHUT DELAY
DOWN
CONSTANT
CURRENT
CONSTANT
VOLTAGE
HORIZONTAL SCALE: 100µs/DIV
Figure 5. Stability Waveforms
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
11
LTC1734
U
W U U
APPLICATIONS INFORMATION
resulting in the IC’s junction temperature to rise above
150°C, thus cutting off the PNP’s base current. This
action will limit the PNP’s junction temperature to some
temperature well above 150°C. The temperature
depends on how well the IC and PNP are thermally
connected and on the transistor’s θJA. See the External
PNP Transistor section for information on protecting the
transistor from overheating.
U
PACKAGE DESCRIPTIO
S6 Package
6-Lead Plastic SOT-23
(LTC DWG # 05-08-1634)
(LTC DWG # 05-08-1636)
2.80 – 3.10
(.110 – .118)
(NOTE 3)
.20
(.008)
A2
A
2.60 – 3.00 1.50 – 1.75
(.102 – .118) (.059 – .069)
(NOTE 3)
DATUM ‘A’
PIN ONE ID
1.90
(.074)
REF
L
.09 – .20
(.004 – .008)
(NOTE 2)
A1
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
SOT-23
SOT-23
(Original)
(ThinSOT)
.90 – 1.45
1.00 MAX
(.039 MAX)
A
A1
A2
L
.95
(.037)
REF
(.035 – .057)
3. DRAWING NOT TO SCALE
4. DIMENSIONS ARE INCLUSIVE OF PLATING
5. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
6. MOLD FLASH SHALL NOT EXCEED .254mm
7. PACKAGE EIAJ REFERENCE IS:
SC-74A (EIAJ) FOR ORIGINAL
JEDEL MO-193 FOR THIN
.00 – 0.15
(.00 – .006)
.01 – .10
(.0004 – .004)
.25 – .50
(.010 – .020)
S6 SOT-23 0401
.90 – 1.30
.80 – .90
(.031 – .035)
(6PLCS, NOTE 2)
(.035 – .051)
.35 – .55
.30 – .50 REF
(.014 – .021)
(.012 – .019 REF)
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT®1510-5
500kHz Constant-Current/Constant-Voltage Battery Charger Up to 1A Charge Current for Li-Ion, NiCd, NiMH or Lead-Acid
Batteries
LT1571-1/LT1571-2 200kHz/500kHz Constant-Current/Constant-Voltage Battery
Up to 1.5A Charge Current for 1-, 2- or Multiple Cell Li-Ion Batteries,
Preset and Adjustable Battery Voltages, C/10 Charge Detection
LT1571-5
Charger Family
LTC1729
Li-Ion Battery Charger Termination Controller
Can be Used with LTC Battery Chargers to Provide Charge Termina-
tion, Preset Voltages, C/10 Charge Detection and Timer Functions
LTC1730
LTC1731
LTC1732
Li-Ion Battery Pulse Charger
Minimizes Heat Dissipation, No Blocking Diode Required,
Limits Maximum Current for Safety
Linear Constant-Current/Constant-Voltage Charger Controller Simple Charger Uses External FET. Features Preset Voltages,
C/10 Charge Detection and Programmable Timer
Linear Constant-Current/Constant-Voltage Charger Controller Simple Charger Uses External FET. Input Power Good Indication
Features Preset Voltages, C/10 Charge Detection and Program-
mable Timer
LT1769
200kHz Constant-Current/Constant-Voltage Battery Charger Up to 2A Charge Current for Li-Ion, NiCd, NiMH or Lead-Acid
Batteries with Input Current Limit
sn1734 1734fs LT/TP 0801 2K • PRINTED IN THE USA
12 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
LINEAR TECHNOLOGY CORPORATION 2001
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明