LTC3737EUF [Linear]
Dual 2-Phase, No RSENSE DC/DC Controller with Output Tracking; 双2相,无检测电阻器DC / DC控制器输出跟踪型号: | LTC3737EUF |
厂家: | Linear |
描述: | Dual 2-Phase, No RSENSE DC/DC Controller with Output Tracking |
文件: | 总24页 (文件大小:304K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC3737
TM
Dual 2-Phase, No RSENSE
,
DC/DC Controller with
Output Tracking
U
FEATURES
DESCRIPTIO
The LTC®3737 is a 2-phase dual step-down switching
regulator controller that requires few external compo-
nents. The constant frequency current mode architecture
provides excellent AC and DC load and line regulation.
MOSFET VDS sensing eliminates the need for current
sense resistors and improves efficiency. Power loss and
noise due to the ESR of the input capacitance are mini-
mized by operating the two controllers out of phase.
■
Sense Resistor Optional
■
Out-of-Phase Controllers Reduce Required
Input Capacitance
Programmable Output Voltage Tracking
■
■
Constant Frequency Current Mode Architecture
■
Wide VIN Range: 2.75V to 9.8V
■
Wide VOUT Range: 0.6V to VIN
■
0.6V ±1.5% Reference
■
Low Dropout Operation: 100% Duty Cycle
Burst Mode operation provides high efficiency operation
at light loads. 100% duty cycle provides low dropout
operation and extends battery operating time.
■
True PLL for Frequency Locking or Adjustment
(Frequency Range 250kHz to 850kHz)
Selectable Burst Mode® or Pulse Skipping Operation
■
Switching frequency can be programmed up to 750kHz,
allowing the use of small surface mount inductors and
capacitors. For noise sensitive applications, the LTC3737
can be externally synchronized from 250kHz to 850kHz.
at Light Loads
Internal Soft-Start Circuitry
Selectable Maximum Peak Current Sense Threshold
Power Good Output Voltage Monitor
Output Overvoltage Protection
■
■
■
■
■
■
Other features include a power good output voltage moni-
tor, a tracking input and internal soft-start.
Micropower Shutdown: IQ = 9µA
Tiny 4mm × 4mm QFN and 24-Lead SSOP Packages
U
The LTC3737 is available in the low profile thermally
enhanced (4mm × 4mm) QFN package or a 24-lead SSOP
narrow package.
APPLICATIO S
■
One or Two Lithium-Ion Powered Devices
, LTC and LT are registered trademarks of Linear Technology Corporation.
Burst Mode is a registered trademark of Linear Technology Corporation.
■
Notebook and Palmtop Computers, PDAs
No R
is a trademark of Linear Technology Corporation.
SENSE
■
U.S. patent numbers 5481178, 5731694, 5929620, 6144194,6580258, 5994885
Portable Instruments
■
Distributed DC Power Systems
U
TYPICAL APPLICATIO
Efficiency vs Load Current
V
IN
100
95
90
85
80
75
70
65
60
55
50
2.75V TO
9.8V
V
= 3.3V
IN
187k
V
= 2.5V
OUT
2.2µH
M1
+
SW1
SENSE1
PV
V
OUT1
2.5V
59k
V
+
FB1
IN1
D1
V
= 1.8V
47µF
47µF
OUT
I
PGATE1
TH1
10µF
×2
15k
15k
PGOOD
SGND
V
220pF
220pF
IN
LTC3737
PGND
RUN/SS
PGATE2
TRACK
D2
2.2µH
+
I
TH2
59k
V
PV
IN2
V
FB2
OUT2
1.8V
+
SW2
SENSE2
M2
118k
1
10
100
1000
10000
3737 F01
LOAD CURRENT (mA)
3737 F01b
Figure 1. High Efficiency, 2-Phase, 550kHz Dual Step-Down Converter
3737f
1
LTC3737
ABSOLUTE AXI U RATI GS
W W
U W
(Note 1)
Input Supply Voltage (VIN), PVIN1, PVIN2
,
Operating Temperature Range (Note 2) ... –40°C to 85°C
Storage Ambient Temperature Range
SENSE1+, SENSE2+ .................................. –0.3V to 10V
PGATE1, PGATE2, PLLLPF, RUN/SS, SYNC/MODE,
TRACK, IPRG1, IPRG2 Voltages .... –0.3V to (VIN + 0.3V)
VFB1, VFB2, ITH1, ITH2 Voltages .................. –0.3V to 2.4V
SW1, SW2 Voltages ............ –2V to VIN + 1V or 10V Max
PGOOD ..................................................... –0.3V to 10V
PGATE1, PGATE2 Peak Output Current (<10µs) ......... 1A
QFN Package .................................... –65°C to 125°C
SSOP Package .................................. –65°C to 150°C
Junction Temperature (Note 3) ............................ 125°C
Lead Temperature (Soldering, 10sec)
LTC3737EGN ................................................... 300°C
U W
U
PACKAGE/ORDER I FOR ATIO
TOP VIEW
ORDER PART
NUMBER
ORDER PART
TOP VIEW
NUMBER
SW1
+
1
2
SENSE1
24
23
22
21
20
19
18
17
16
15
14
13
–
(SENSE1 )
PV
IN1
IPRG1
LTC3737EGN
LTC3737EUF
24 23 22 21 20 19
3
NC
V
FB1
TH1
SYNC/
I
1
2
3
4
5
6
18
17
16
TH1
4
SYNC/MODE
PGATE1
PGND
MODE
I
IPRG2
PLLLPF
SGND
PGATE1
5
IPRG2
PLLLPF
SGND
PGND
6
25
15 PGATE2
14 RUN/SS
13 NC
7
PGATE2
RUN/SS
NC
V
IN
8
V
IN
TRACK
UF PART
MARKING
9
TRACK
7
8
9 10 11 12
10
11
12
PV
IN2
V
FB2
+
SENSE2
I
TH2
3737
SW2
PGOOD
–
(SENSE2 )
UF PACKAGE
GN PACKAGE
24-LEAD (4mm × 4mm) PLASTIC QFN
24-LEAD (NARROW) PLASTIC SSOP
TJMAX = 125°C, θJA = 37°C/W
EXPOSED PAD IS PGND (PIN 25) MUST BE SOLDERED TO PCB
TJMAX = 125°C, θJA = 130°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes specifications that apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. VIN = 4.2V unless otherwise specified.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Main Control Loops
Input DC Supply Current
Sleep Mode
Shutdown
(Note 4)
220
9
3
325
20
10
µA
µA
µA
RUN/SS = 0V
UVLO
V
IN
< UVLO Threshold
Undervoltage Lockout Threshold
V
IN
V
IN
Falling
Rising
●
●
1.95
2.15
2.25
2.45
2.55
2.75
V
V
Shutdown Threshold at RUN/SS
Start-Up Current Source
0.45
0.5
0.65
0.7
0.85
1
V
RUN/SS = 0V
µA
Regulated Feedback Voltage
0°C to 85°C (Note 5)
–40°C to 85°C
0.591
0.588
0.6
0.6
0.609
0.612
V
V
●
Output Voltage Line Regulation
2.75V < V < 9.8V (Note 5)
0.05
0.2
mV/V
IN
3737f
2
LTC3737
ELECTRICAL CHARACTERISTICS
The ● denotes specifications that apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. VIN = 4.2V unless otherwise specified.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Output Voltage Load Regulation
I
I
= 0.9V (Note 5)
= 1.7V
0.12
–0.12
0.5
–0.5
%
%
TH
TH
V
Input Current
(Note 5)
10
10
50
50
nA
nA
V
FB1,2
TRACK Input Current
TRACK = 0.6V
Measured at V
Overvoltage Protect Threshold
Overvoltage Protect Hysteresis
Auxiliary Feedback Threshold
Gate Drive 1, 2 Rise Time
Gate Drive 1, 2 Fall Time
0.66
0.68
20
0.7
FB
mV
V
SYNC/MODE Ramping Negative
C = 3000pF
0.525
0.6
40
0.675
ns
ns
L
C = 3000pF
L
40
Maximum Current Sense Voltage
IPRG = Floating (Note 6)
IPRG = 0V (Note 6)
●
●
●
110
70
185
125
85
204
140
100
223
mV
mV
mV
+
(SENSE – SW)(∆V
)
SENSE(MAX)
IPRG = V (Note 6)
IN
Soft-Start Time
Time for V to Ramp from 0.05V to 0.55V
0.667
0.833
1
ms
FB1
Oscillator and Phase-Locked Loop
Oscilator Frequency
Unsynchronized (SYNC/MODE Not Clocked)
V
V
V
= Floating
= 0V
●
●
●
480
260
650
550
300
750
600
340
825
kHz
kHz
kHz
PLLLPF
PLLLPF
PLLLPF
= V
IN
Phase-Locked Loop Lock Range
SYNC/MODE Clocked
Minimum Synchronizable Frequency
Maximum Synchronizable Frequency
●
●
200
1150
250
kHz
kHz
850
Phase Detector Output Current
Sinking
f
f
> f
SYNC/MODE
< f
SYNC/MODE
–4
4
µA
µA
OSC
OSC
Sourcing
PGOOD Output
PGOOD Voltage Low
PGOOD Trip Level
I
Sinking 1mA
125
mV
PGOOD
V
with Respect to Set Output Voltage
FB
V
FB
V
FB
V
FB
V
FB
< 0.6V, Ramping Positive
< 0.6V, Ramping Negative
> 0.6V, Ramping Negative
> 0.6V, Ramping Positive
–13
–16
13
–10.0
–13.3
10.0
–7
–10
7
%
%
%
%
16
13.3
10
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 4: Dynamic supply current is higher due to gate charge being
delivered at the switching frequency.
Note 2: The LTC3737E is guaranteed to meet specified performance from
0°C to 70°C. Specifications over the –40°C to 85°C operating range are
assured by design, characterization and correlation with statistical process
controls.
Note 5: The LTC3737 is tested in a feedback loop that servos I to a
TH
specified voltage and measures the resultant V voltage.
FB
Note 6: Peak current sense voltage is reduced dependent on duty cycle to
a percentage of value as shown in Figure 2.
Note 3: T is calculated from the ambient temperature T and power
J
A
dissipation P according to the following formula:
D
T = T + (P • θ °C/W)
J
A
D
JA
3737f
3
LTC3737
TYPICAL PERFOR A CE CHARACTERISTICS
U W
Efficiency vs Load Current
Efficiency vs Load Current
Load Step (Burst Mode Operation)
100
95
90
85
80
75
70
65
60
55
50
100
95
90
85
80
75
70
65
60
55
50
T
= 25°C
OUT
Burst Mode OPERATION
A
V
= 2.5V
(SYNC/MODE = V
)
V
IN
= 3.3V
IN
V
OUT
AC-COUPLED
100mV/DIV
V
IN
= 4.2V
V
IN
= 5V
PULSE SKIPPING
(SYNC/MODE = 0V)
I
L
2A/DIV
T
V
V
= 25°C
A
= 3.3V
IN
OUT
V
V
I
= 3.3V
200µs/DIV
3737 G03
IN
OUT
= 2.5V
= 1.8V
= 300mA TO 3A
FIGURE 13 CIRCUIT
1000 10000
LOAD CURRENT (mA)
LOAD
SYNC/MODE = V
1
10
100
1000
10000
1
10
100
IN
FIGURE 13 CIRCUIT
LOAD CURRENT (mA)
3737 G01
3737 G02
Tracking Start-Up with Internal
Soft-Start (CSS = 0nF)
Tracking Start-Up with External
Soft-Start (CSS = 10nF)
Load Step (Pulse Skipping Mode)
V
V
OUT1
OUT1
2.5V
2.5V
V
OUT
AC-COUPLED
100mV/DIV
V
V
OUT2
OUT2
1.8V
1.8V
500mV/
DIV
500mV/
DIV
I
L
2A/DIV
V
V
I
= 3.3V
200µs/DIV
3737 G04
V
= 4.2V
LOAD1
250µs/DIV
= 1Ω
3737 G05
V
= 4.2V
LOAD1
2.5ms/DIV
3737 G06
IN
OUT
IN
IN
= 1.8V
R
= R
R
= R
= 1Ω
LOAD2
LOAD2
= 300mA TO 3A
FIGURE 13 CIRCUIT
FIGURE 13 CIRCUIT
LOAD
SYNC/MODE = 0V
FIGURE 13 CIRCUIT
Regulated Feedback Voltage
vs Temperature
Maximum Current Sense Threshold
vs Temperature
Shutdown (RUN) Threshold
vs Temperature
135
130
125
120
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.609
0.607
0.605
0.603
0.601
0.599
0.597
0.595
0.593
0.591
I
= FLOAT
PRG
115
–60 –40 –20
0
20 40 60 80 100
20 40
–60 –40 –20
TEMPERATURE (°C)
–60
80
0
60 80 100
–40 –20
0
20
TEMPERATURE (°C)
40
60
100
TEMPERATURE (°C)
3737 G08
3737 G07
3737 G09
3737f
4
LTC3737
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Undervoltage Lockout Threshold
vs Temperature
RUN/SS Pull-Up Current
vs Temperature
Oscillator Frequency
vs Temperature
10
8
2.50
2.45
2.40
2.35
2.30
2.25
2.20
2.15
2.10
1.0
0.9
0.8
0.7
0.6
0.5
0.4
V
RISING
IN
6
4
2
0
V
IN
FALLING
–2
–4
–6
–8
–10
20 40
–60 –40 –20
0
20 40 60 80 100
–60
80
–60 –40 –20
0
60 80 100
20
TEMPERATURE (°C)
60
–40 –20
0
40
100
TEMPERATURE (°C)
TEMPERATURE (°C)
3737 G10
3737 G11
3737 G12
Oscillator Frequency
vs Input Voltage
Shutdown Quiescent Current
vs Input Voltage
RUN/SS Start-Up Current
vs Input Voltage
5
4
20
18
16
14
12
10
8
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
T
A
= 25°C
T
= 25°C
T
= 25°C
A
A
RUN/SS = 0V
RUN/SS = 0V
3
2
1
0
–1
–2
–3
–4
–5
6
4
2
0
2
6
8
9
3
4
5
7
10
2
6
8
9
3
4
5
7
10
6
7
2
3
4
5
8
9
10
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
3737 G13
3737 G14
3737 G15
3737f
5
LTC3737
U
U
U
PI FU CTIO S (QFN/SSOP)
ITH1, ITH2 (Pins 1, 8/Pins 4, 11): Current Threshold and
Error Amplifier Compensation Point. Nominal operating
rangeonthesepinsisfrom0.7Vto2V.Thevoltageonthis
pin determines the threshold of the main current
comparator.
PGND (Pin 16/Pin 19): Power Ground. This pin serves as
the ground connection for the gate drivers.
PGATE1, PGATE2 (Pins 17, 15/Pins 20, 18): Gate Drives
for External P-Channel MOSFETs. These pins have an
output swing from PGND to SENSE+.
PLLLPF (Pin 3/Pin 6): Frequency Set/PLL Lowpass Filter.
Whensynchronizingtoanexternalclock,thispinservesas
the lowpass filter point for the phase-locked loop. Nor-
mally, a series RC is connected between this pin and
ground.
SYNC/MODE (Pin 18/Pin 21): External Clock Synchroni-
zation and Burst Mode/Pulse Skipping Select. Applying a
clock with frequency between 250kHz to 850kHz causes
the internal oscillator to phase lock to the external clock,
and disables Burst Mode operation but allows pulse skip-
ping at low load currents. Forcing this pin high enables
Burst Mode operation. Forcing this pin low enables pulse-
skipping mode. In these cases, the frequency of the
internal oscillator is set by the voltage on the PLLLPF pin.
Do not let this pin float.
Whennotsynchronizingtoanexternalclock,thispinserves
asthefrequencyselectinput. TyingthispintoGNDselects
300kHz operation; tying this pin to VIN selects 750kHz
operation. Floating this pin selects 550kHz operation.
SGND (Pin 4/Pin 7): Signal Ground. This pin serves as the
ground connection for most internal circuits.
PVIN1, PVIN2 (Pins 20, 12/Pins 23, 15): Powers of the
Gate Drivers.
VIN (Pin 5/Pin 8): Chip Signal Power Supply. This pin
powers the entire chip except for the gate drivers. Exter-
nally filtering this pin with a lowpass RC network (e.g., R
= 10Ω, C = 1µF) is suggested to minimize noise pickup,
especially in high load current applications.
SENSE1+, SENSE2+ (Pins 21, 11/Pins 24, 14): Positive
Inputs to Differential Current Comparators. Normally con-
nected to the sources of the external P-channel MOSFETs.
SW1 (SENSE1–), SW2 (SENSE2–) (Pins 22, 10/Pins 1,
13): Switch Node Connections to Inductors. Also the
negative inputs to differential peak current comparators.
Normally connected to the drains of the external P-Chan-
nel MOSFETs and the inductor when not using a sense
resistor. When a sense resistor is used, it will be con-
nected between SW and SENSE+.
TRACK (Pin 6/Pin 9): Tracking Input for Second Control-
ler. This pin allows the start-up of VOUT2 to “track” that of
VOUT1 according to a ratio established by a resistor divider
on VOUT1 connected to the TRACK pin. For one-to-one
tracking of VOUT1 and VOUT2 during start-up, a resistor
divider with values equal to those connected to VFB2 from
VOUT2 should be used to connect to TRACK from VOUT1
.
IPRG1, IPRG2 (Pins 23, 2/Pins 2, 5): Three-State Pins to
Select Maximum Peak Sense Voltage Threshold. These
pins select the maximum allowed voltage drop between
the SENSE+ and SW pins (i.e., the maximum allowed drop
across the external P-channel MOSFET) for each channel.
Tie high, low or float to select 204mV, 85mV or 125mV,
respectively.
PGOOD (Pin 9/Pin 12):Power Good Output Voltage Moni-
tor Open-Drain Logic Output. This pin is pulled to ground
when the voltage on either feedback pin (VFB1, VFB2) is not
within ±13.3% of its nominal set point.
NC (Pins 13, 19/Pins 16, 22): No Connect.
RUN/SS (Pin 14/Pin 17): Run Control Input and Optional
External Soft-Start Input. Forcing this pin below 0.65V
shuts down the chip (both channels). Driving this pin to
VIN or releasing this pin enables the chip to start-up with
the internal soft-start. An external soft-start can be pro-
grammed by connecting a capacitor between this pin and
ground.
VFB1, VFB2 (Pins 24, 7/Pins 3, 10): Each receives the
remotely sensed feedback voltage for its controller from
an external resistive divider across the output.
Exposed Pad (Pin 25/NA): Exposed Pad is PGND and
must be soldered to PCB.
3737f
6
LTC3737
U
U
W
FU CTIO AL DIAGRA
L1
D1
M1
V
OUT1
V
IN
C
C
OUT
IN
V
IN
+
SENSE1
IPROG1
PV
SW1
IN1
SLOPE1
VOLTAGE
V
REF
SWITCHING
LOGIC AND
BLANKING
CIRCUIT
CLK1
S
R
REFERENCE
0.6V
PGATE1
PGND
–
+
Q
I
CMP
UV
UNDERVOLTAGE
LOCKOUT
+
–
UVSD
V
IN
OV1
OVP
CMSD
+
0.68V
SLEEP1
V
IN
0.15V
–
+
–
R1B
R
TRACKB
0.3V
0.5µA
SC1
BURSTDIS
SCP
RUN/SS
0.12V
0.54V
EXTSS
+
–
C
SS
I
t = 1ms
TH1
INTERNAL
–
+
+
SOFT-START
R
MUX
SOFT-
START
C
+
–
INTSS
C
C
PGOOD1
OV1
BURSTDIS
BURST DEFEAT
CLOCK DETECT
DUPLICATE FOR SECOND CHANNEL
SYNC/MODE
PLLLPF
PHASE
DETECTOR
V
FB1
–
+
+
R1A
I
V
= 0.6V
EAMP1
TH1
REF
–
SOFT-START
SLOPE1
SLOPE2
VOLTAGE
CONTROLLED
OSCILLATOR
SLOPE
CLK1
V
REF
= 0.6V
TRACK
I
+
+
EAMP2
TH2
COMP
V
FB2
CLK2
V
IN
R2B
R2A
V
OUT2
PGOOD1
PGOOD2
R
TRACKA
PGOOD
SGND
3737 BD
UVSD
3737f
7
LTC3737
U
(Refer to Functional Diagram)
OPERATIO
Main Control Loop
than the 0.6V internal reference, the LTC3737 regulates
the VFB2 voltage to the TRACK pin instead of the 0.6V
reference. Typically, a resistor divider on VOUT1 is con-
nected to the TRACK pin to allow the start-up of VOUT2 to
“track”thatofVOUT1.Forone-to-onetrackingduringstart-
up, the resistor divider would have the same values as the
The LTC3737 uses a constant frequency, current mode
architecture with the two controller channels operating
180 degrees out of phase. During normal operation, each
external P-channel power MOSFET is turned on when the
clock for that channel sets the RS latch, and turned off
when the current comparator (ICMP) resets the latch. The
peak inductor current at which ICMP resets the RS latch is
determined by the voltage on the ITH pin, which is the
output of each error amplifier (EAMP). The VFB pin re-
ceives the output voltage feedback signal from an external
resistor divider. This feedback signal is compared to the
internal 0.6V reference voltage by the EAMP. When the
load current increases, it causes a slight decrease in VFB
relative to the 0.6V reference, which in turn, causes the ITH
voltage to increase until the average inductor current
matches the new load current.
divider on VOUT2 that is connected to VFB2
.
If no tracking function is desired, then the TRACK pin can
be tied to VIN. Note, however, that in this situation, there
would be no (internal or external) soft-start on VOUT2
.
Light Load Operation (Burst Mode Operation or Pulse
Skipping Mode) (SYNC/MODE Pin)
The LTC3737 can be enabled to enter high efficiency Burst
Modeoperationatlowloadcurrents. ToselectBurstMode
operation, tie the SYNC/MODE pin to a DC voltage above
0.6V (e.g., VIN). To disable Burst Mode operation and
enable PWM pulse skipping mode, connect SYNC/MODE
to a DC voltage below 0.6V (e.g., SGND). In this mode, the
efficiency is lower at light loads. However, pulse skipping
mode has the advantages of lower output ripple and less
interference to audio circuitry.
Shutdown, Soft-Start and Tracking Start-Up
(RUN/SS and TRACK Pins)
The LTC3737 is shut down by pulling the RUN/SS pin low.
In shutdown, all controller functions are disabled and the
chip draws only 9µA. The PGATE outputs are held high
(off) in shutdown. Releasing RUN/SS allows an internal
0.7µA current source to charge up the RUN/SS pin. When
the RUN/SS pin reaches 0.65V, the LTC3737’s two con-
trollers are enabled.
When a controller is in Burst Mode operation, the peak
current in the inductor is set to approximate one-fourth of
the maximum sense voltage even when the voltage on the
ITH pin indicates a lower value. If the average inductor
current is greater than the load current, the EAMP will
decrease the voltage on the ITH pin. When the ITH voltage
drops below 0.85V, the internal SLEEP signal goes high
and the external MOSFET is turned off.
The start-up of VOUT1 is controlled by the LTC3737’s
internal soft-start. During soft-start, the error amplifier
EAMP compares the feedback signal VFB1 to the internal
soft-startramp(insteadofthe0.6Vreference),whichrises
linearly from 0V to 0.6V in about 1ms. This allows the
output voltage to rise smoothly from 0V to its final value,
while maintaining control of the inductor current.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC3737 draws.
Theloadcurrentissuppliedbytheoutputcapacitor.Asthe
output voltage decreases, the EAMP increases the ITH
voltage. When the ITH voltage reaches 0.925V, the SLEEP
signal goes low and the controller resumes normal opera-
tion by turning on the external P-channel MOSFET on the
next cycle of the internal oscillator.
The 1ms soft-start time can be increased by connecting
theoptionalexternalsoft-startcapacitor,CSS,betweenthe
RUN/SS and SGND pins. As the RUN/SS pin continues to
rise linearly from approximately 0.65V to 1.3V (being
charged by the internal 0.7µA current source), the EAMP
regulates VFB1 linearly from 0V to 0.6V.
When the SYNC/MODE pin is clocked by an external clock
source to use the phase-locked loop (see Frequency
SelectionandPhase-LockedLoop),theLTC3737operates
in PWM pulse skipping mode at light loads.
The start-up of VOUT2 is controlled by the voltage on the
TRACK pin. When the voltage on the TRACK pin is less
3737f
8
LTC3737
U
(Refer to Functional Diagram)
OPERATIO
When a controller is in pulse skipping operation, an
internal offset at the current comparator input will assure
that the current comparator remains tripped even at zero
load current and the regulator will start to skip cycles, as
it must, in order to maintain regulation.
A phase-locked loop (PLL) is available on the LTC3737 to
synchronize the internal oscillator to an external clock
source that is connected to the SYNC/MODE pin. In this
case, a series RC should be connected between the
PLLLPFpinandSGNDtoserveasthePLL’sloopfilter. The
LTC3737phasedetectoradjuststhevoltageonthePLLLPF
pintoaligntheturn-onofcontroller1’sexternalP-channel
MOSFET to the rising edge of the synchronizing signal.
Thus, the turn-on of controller 2’s external P-channel
MOSFET is 180 degrees out of phase to the rising edge of
the external clock source.
Short-Circuit Protection
When one of the outputs is shorted to ground (VFB
<
0.12V), the switching frequency of that controller is re-
duced to 1/3 of the normal operating frequency. The other
controller is unaffected and maintains normal operation.
The typical capture range of the LTC3737’s phase-locked
loop is from approximately 200kHz to 1MHz, with a
guarantee over all variations and temperature to be be-
tween 250kHz and 850kHz. In other words, the LTC3737’s
PLL is guaranteed to lock to an external clock source
whose frequency is between 250kHz and 850kHz.
The short-circuit threshold on VFB2 is based on the
smaller of 0.12V and a fraction of the voltage on the
TRACK pin. This also allows VOUT2 to start up and track
VOUT1 more easily. Note that if VOUT1 is truly short
circuited (VOUT1 = VFB1 = 0V), then the LTC3737 will try to
regulate VOUT2 to 0V if a resistor divider on VOUT1 is
connected to the TRACK pin.
Dropout Operation
Output Overvoltage Protection
When the input supply voltage (VIN) decreases towards
the output voltage, the rate of change of the inductor
current while the external P-channel MOSFET is on (ON
cycle)decreases.ThisreductionmeansthattheP-channel
MOSFET will remain on for more than one oscillator cycle
if the inductor current has not ramped up to the threshold
set by the EAMP on the ITH pin. Further reduction in the
input supply voltage will eventually cause the P-channel
MOSFET to be turned on 100%; i.e., DC. The output
voltage will then be determined by the input voltage minus
the voltage drop across the P-channel MOSFET and the
inductor.
Asafurtherprotection, theovervoltagecomparator(OVP)
guardsagainsttransientovershoots,aswellasothermore
seriousconditions,thatmayovervoltagetheoutput.When
the feedback voltage on the VFB pin has risen 13.33%
above the reference voltage of 0.6V, the external P-chan-
nel MOSFET is turned off until the overvoltage is cleared.
Frequency Selection and Phase-Locked Loop (PLLLPF
and SYNC/MODE Pins)
The selection of switching frequency is a tradeoff between
efficiency and component size. Low frequency operation
increasesefficiencybyreducingMOSFETswitchinglosses,
butrequireslargerinductanceand/orcapacitancetomain-
tain low output ripple voltage.
Undervoltage Lockout
TopreventoperationoftheP-channelMOSFETbelowsafe
input voltage levels, an undervoltage lockout is incorpo-
rated in the LTC3737. When the input supply voltage (VIN)
drops below 2.25V, the external P-channel MOSFET and
allinternalcircuitryareturnedoffexceptfortheundervolt-
age block, which draws only a few microamperes.
The switching frequency of the LTC3737’s controllers can
be selected using the PLLLPF pin. If the SYNC/MODE pin
isnotbeingdrivenbyanexternalclocksource,thePLLLPF
pin can be floated, tied to VIN or tied to SGND to select
550kHz, 750kHz or 300kHz, respectively.
3737f
9
LTC3737
U
(Refer to Functional Diagram)
OPERATIO
Peak Current Sense Voltage Selection and Slope
Thepeakinductorcurrentisdeterminedbythepeaksense
voltage and the on-resistance of the external P-channel
MOSFET:
Compensation (IPRG1 and IPRG2 Pins)
When a controller is operating below 20% duty cycle, the
peak current sense voltage (between the SENSE+ and SW
pins) allowed across the external P-channel MOSFET is
determined by:
∆VSENSE(MAX)
IPK
=
RDS(ON)
Power Good (PGOOD) Pin
A V – 0.7V
(
)
ITH
∆VSENSE(MAX)
=
10
A window comparator monitors both feedback voltages
and the open-drain PGOOD output pin is pulled low when
either or both feedback voltages are not within ±10% of
the 0.6V reference voltage. PGOOD is low when the
LTC3737 is shutdown or in undervoltage lockout.
where A is a constant determined by the state of the IPRG
pins.
Floating the IPRG pin selects A = 1; tying IPRG to VIN
selects A = 5/3; tying IPRG to SGND selects A = 2/3. The
maximum value of VITH is typically about 1.98V, so the
maximum sense voltage allowed across the external
P-channel MOSFET is 125mV, 85mV or 204mV for the
three respective states of the IPRG pin. The peak sense
voltages for the two controllers can be independently
selected by the IPRG1 and IPRG2 pins.
2-Phase Operation
Why the need for 2-phase operation? Until recently, con-
stant frequency dual switching regulators operated both
controllers in phase (i.e., single phase operation). This
means that both topside MOSFETs (P-channel) are turned
on at the same time, causing current pulses of up to twice
the amplitude of those from a single regulator to be drawn
from the input capacitor. These large amplitude pulses
increase the total RMS current flowing in the input capaci-
tor, requiring the use of larger and more expensive input
capacitors, and increase both EMI and power losses in the
input capacitor and input power supply.
However, once the controller’s duty cycle exceeds 20%,
slope compensation begins and effectively reduces the
peak sense voltage by a scale factor given by the curve in
Figure 2.
110
100
90
80
70
60
50
40
30
20
10
0
With2-phaseoperation,thetwocontrollersoftheLTC3737
are operated 180 degrees out of phase. This effectively
interleaves the current pulses coming from the topside
MOSFET switches, greatly reducing the time where they
overlap and add together. The result is a significant
reductioninthetotalRMScurrent,whichinturnallowsthe
use of smaller, less expensive input capacitors, reduces
shielding requirements for EMI and improves real world
operating efficiency.
0
10 20 30 40 50 60 70 80 90 100
DUTY CYCLE (%)
Figure 3 shows qualitatively example waveforms for a
single phase dual controller versus a 2-phase LTC3737
system. In this case, 2.5V and 1.8V outputs, each drawing
3737 F02
Figure 2. Maximum Peak Current vs Duty Cycle
3737f
10
LTC3737
U
(Refer to Functional Diagram)
OPERATIO
Single Phase
2-Phase
Dual Controller
RMS input current and voltage. Significant cost and board
footprint savings are also realized by being able to use
smaller, less expensive, lower RMS current-rated, input
capacitors.
Dual Controller
SW1 (V)
SW2 (V)
Ofcoursetheimprovementaffordedby2-phaseoperation
is a function of the relative duty cycles of the two control-
lers, which in turn are dependent upon the input supply
voltage. Figure4depictshowtheRMSinputcurrentvaries
for single phase and 2-phase dual controllers with 2.5V
and 1.8V outputs over a wide input voltage range.
I
I
L1
L2
2.0
1.8
SINGLE PHASE
1.6
DUAL CONTROLER
1.4
I
IN
2-PHASE
1.2
1.0
0.8
0.6
0.4
0.2
0
DUAL CONTROLER
3737 F03
Figure 3. Example Waveforms for a Single Phase
Dual Controller vs the 2-Phase LTC3737
V
V
= 2.5V/2A
= 1.8V/2A
OUT1
OUT2
a load current of 2A, are derived from a 7V (e.g., a 2-cell
Li-Ion battery) input supply. In this example, 2-phase
operation would reduce the RMS input capacitor current
from 1.79ARMS to 0.91ARMS. While this is an impressive
reduction by itself, remember that power losses are pro-
portional to IRMS2, meaning that actual power wasted is
reduced by a factor of 3.86.
2
6
8
9
3
4
5
7
10
INPUT VOLTAGE (V)
3737 F04
Figure 4. RMS Input Current Comparison
It can be readily seen that the advantages of 2-phase
operation are not limited to a narrow operating range, but
in fact extend over a wide region. A good rule of thumb for
mostapplicationsisthat2-phaseoperationwillreducethe
input capacitor requirement to that for just one channel
operating at maximum current and 50% duty cycle.
The reduced input ripple current also means that less
power is lost in the input power path, which could include
batteries, switches, trace/connector resistances, and pro-
tection circuitry. Improvements in both conducted and
radiated EMI also directly accrue as a result of the reduced
3737f
11
LTC3737
W U U
U
APPLICATIO S I FOR ATIO
The typical LTC3737 application circuit is shown in Figure
1.ExternalcomponentselectionforeachoftheLTC3737’s
controllers is driven by the load requirement and begins
with the selection of the inductor (L) and the power
MOSFET M1. Next, the output diode D1 is selected. Finally
CIN and COUT are chosen.
A reasonable starting point is setting ripple current IRIPPLE
to be 40% of IOUT(MAX). Rearranging the above equation
yields:
∆VSENSE(MAX)
5
6
RDS(ON)(MAX)
=
•
for Duty Cycle < 20%
IOUT(MAX)
However, for operation above 20% duty cycle, slope
compensation has to be taken into consideration to select
the appropriate value of RDS(ON) to provide the required
amount of load current:
Power MOSFET Selection
An external P-channel MOSFET must be selected for use
with each channel of the LTC3737. The main selection
criteria for the power MOSFET are the breakdown voltage
∆VSENSE(MAX)
IOUT(MAX)
V
BR(DSS), threshold voltage VGS(TH), on-resistance
5
6
R
DS(ON)(MAX) = • SF •
RDS(ON), reverse transfer capacitance CRSS and the total
gate charge QG.
whereSFisascalefactorwhosevalueisobtainedfromthe
curve in Figure 2.
Thegatedrivevoltageistheinputsupplyvoltage.Sincethe
LTC3737 is designed for operation down to low input
voltages, a sublogic level MOSFET (RDS(ON) guaranteed at
VGS = 2.5V) is required for applications that work close to
this voltage. When these MOSFETs are used, make sure
that the input supply to the LTC3737 is less than the abso-
lute maximum MOSFET VGS rating, which is typically 8V.
These must be further derated to take into account the
significant variation in on-resistance with temperature.
Thefollowingequationisagoodguidefordeterminingthe
required RDS(ON)MAX at 25°C (manufacturer’s specifica-
tion), allowing some margin for variations in the LTC3737
and external component values:
The P-channel MOSFET’s on-resistance is chosen based
on the required load current. The maximum average
output load current, IOUT(MAX), is equal to the peak induc-
tor current minus half the peak-to-peak ripple current,
IRIPPLE. The LTC3737’s current comparator monitors the
drain-to-source voltage, VDS, of the P-channel MOSFET,
which is sensed between the SENSE+ and SW pins. The
peak inductor current is limited by the current threshold,
setbythevoltageontheITH pin,ofthecurrentcomparator.
The voltage on the ITH pin is internally clamped, which
limitsthemaximumcurrentsensethreshold∆VSENSE(MAX)
to approximately 125mV when IPRG is floating (85mV
when IPRG is tied low; 204mV when IPRG is tied high).
∆VSENSE(MAX)
IOUT(MAX) • ρT
5
6
R
DS(ON)(MAX) = • 0.9 • SF •
TheρTisanormalizingtermaccountingforthetemperature
variationinon-resistance,whichistypicallyabout0.4%/°C,
as shown in Figure 5. Junction to case temperature TJC is
2.0
1.5
1.0
0.5
0
The output current that the LTC3737 can provide is given
by:
∆VSENSE(MAX)
IRIPPLE
IOUT(MAX)
=
–
RDS(ON)
2
50
100
–50
150
0
JUNCTION TEMPERATURE (°C)
3737 F05
where IRIPPLE is the inductor peak-to-peak ripple current
(see Inductor Value Calculation).
Figure 5. RDS(ON) vs Temperature
3737f
12
LTC3737
W U U
APPLICATIO S I FOR ATIO
U
about 10°C in most applications. For a maximum ambient
temperature of 70°C, using ρ80°C ~ 1.3 in the above
equation is a reasonable choice.
Variation in the resistance of a sense resistor is much
smaller than the variation in on-resistance of the external
MOSFET. Thereforetheloadcurrentiswellcontrolled, and
the system is more stable with a sense resistor. However
thesenseresistorcausesextraI2Rlossesinadditiontothe
I2R losses of the MOSFET. Therefore, using a sense
resistor lowers the efficiency of LTC3737, especially for
large load current.
The power dissipated in the MOSFET strongly depends on
its respective duty cycles and load current. When the
LTC3737isoperatingincontinuousmode, thedutycycles
for the MOSFET are:
V
OUT + VD
Duty Cycle =
Operating Frequency and Synchronization
V + VD
IN
The choice of operating frequency, fOSC, is a tradeoff
between efficiency and component size. Low frequency
operationimprovesefficiencybyreducingMOSFETswitch-
ing losses, both gate charge loss and transition loss.
However, lowerfrequencyoperationrequiresmoreinduc-
tance for a given amount of ripple current.
The MOSFET power dissipations at maximum output
current are:
V
OUT + VD
P =
P
• I
(
2 • ρT •RDS(ON) + k •
OUT(MAX)
)
V + VD
IN
V
IN
2 •IOUT(MAX) • ρT •RDS(ON)
The internal oscillator for each of the LTC3737’s control-
lersrunsatanominal550kHzfrequencywhenthePLLLPF
pin is left floating and the SYNC/MODE pin is a DC low or
high. Pulling the PLLLPF to VIN selects 750kHz operation;
pulling the PLLLPF to GND selects 300kHz operation.
The MOSFET has I2R losses and the PP equation includes
an additional term for transition losses, which are largest
at high input voltages. The constant k = 2A–1 can be used
to estimate the amount of transition loss.
Alternatively, the LTC3737 will phase lock to a clock signal
applied to the SYNC/MODE pin with a frequency between
250kHz and 850kHz (see Phase-Locked Loop and Fre-
quency Synchronization).
Using a Sense Resistor
AsenseresistorRSENSE canbeconnectedbetweenSENSE+
and SW to sense the output load current. In this case, the
source of the P-channel MOSFET is connected to the SW
pin and the drain is not connected to any pin of the
LTC3737. Therefore, the current comparator monitors the
voltage developed across RSENSE instead of VDS of the
P-channel MOSFET. The output current that the LTC3737
can provide in this case is given by:
Inductor Value Calculation
Given the desired input and output voltages, the inductor
value and operating frequency, fOSC, directly determine
the inductor’s peak-to-peak ripple current:
V
OUT
+ V / V + V
D) (
(
)
IN
D
IRIPPLE = V – V
(
)
IN
OUT
∆VSENSE(MAX)
IRIPPLE
fOSC •L
IOUT(MAX)
=
–
RSENSE
2
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors, and output voltage
ripple. Thus, highest efficiency operation is obtained at
low frequency with a small ripple current. Achieving this,
however, requires a large inductor.
Setting ripple current as 40% of IOUT(MAX) and using
Figure 2 to choose SF, the value of RSENSE is:
∆VSENSE(MAX)
IOUT(MAX)
5
6
R
SENSE = • SF •
A reasonable starting point is to choose a ripple current
that is about 40% of IOUT(MAX). Note that the largest ripple
current occurs at the highest input voltage. To guarantee
(See the RDS(ON) selection in Power MOSFET Selection).
3737f
13
LTC3737
W U U
U
APPLICATIO S I FOR ATIO
that ripple current does not exceed a specified maximum,
the inductor should be chosen according to:
more turns of wire and therefore copper losses will in-
crease. Ferrite designs have very low core losses and are
preferred at high switching frequencies, so design goals
canconcentrateoncopperlossandpreventingsaturation.
Ferrite core material saturates “hard”, which means that
inductance collapses abruptly when the peak design cur-
rent is exceeded. Core saturation results in an abrupt
increase in inductor ripple current and consequent output
voltage ripple. Do not allow the core to saturate!
V – VOUT
fOSC •IRIPPLE V + VD
VOUT + VD
IN
L ≥
•
IN
Burst Mode Operation Considerations
The choice of RDS(ON) and inductor value also determines
the load current at which the LTC3737 enters Burst Mode
operation. When bursting, the controller clamps the peak
inductor current to approximately:
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool Mµ. Toroids are very space efficient,
especially when several layers of wire can be used, while
inductors wound on bobbins are generally easier to sur-
face mount. However, designs for surface mount that do
not increase the height significantly are available from
Coiltronics, Coilcraft, Dale and Sumida.
∆VSENSE(MAX)
1
4
I
BURST(PEAK) = •
RDS(ON)
Thecorrespondingaveragecurrentdependsontheamount
of ripple current. Lower inductor values (higher IRIPPLE
)
willreducetheloadcurrentatwhichBurstModeoperation
begins.
Output Diode Selection
The ripple current is normally set so that the inductor
current is continuous during the burst periods. Therefore,
The catch diode carries load current during the switch off
time of the power MOSFETs . The average diode current is
thereforedependentontheP-channelMOSFETdutycycle.
At high input voltages, the diode conducts most of the
time. As VIN approaches VOUT, the diode conducts for only
a small fraction of the time. The most stressful condition
for the diode is when the output is short circuited. Under
this condition, the diode must safely handle IPEAK at close
to 100% duty cycle. Therefore, it is important to ad-
equatelyspecifythediodepeakcurrentandaveragepower
dissipation so as not to exceed the diode’s ratings.
I
RIPPLE ≤ IBURST(PEAK)
This implies a minimum inductance of:
V – VOUT OUT + VD
V
IN
LMIN
≥
•
fOSC •IBURST(PEAK) V + VD
IN
A smaller value than LMIN could be used in the circuit,
although the inductor current will not be continuous
during burst periods, which will result in slightly lower
efficiency. In general, though, it is a good idea to keep
Under normal conditions, the average current conducted
by the diode is:
IRIPPLE comparable to IBURST(PEAK)
.
Inductor Core Selection
V – VOUT
V + VD
IN
IN
ID =
•IOUT
Once the value of L is known, the type of inductor must be
selected. High efficiency converters generally cannot af-
ford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
or Kool Mµ® cores. Actual core loss is independent of core
sizeforafixedinductorvalue, butisverydependentonthe
inductance selected. As inductance increases, core losses
go down. Unfortunately, increased inductance requires
The allowable forward voltage drop in the diode is calcu-
lated from the maximum short-circuit current as:
PD
IPEAK
V ≈
F
Kool Mµ is a registered trademark of Magnetics, Inc.
3737f
14
LTC3737
W U U
APPLICATIO S I FOR ATIO
U
where PD is the allowable power dissipation and will be
determined by efficiency and/or thermal requirements.
paralleled to meet size or height requirements in the
design.DuetothehighoperatingfrequencyoftheLTC3737,
ceramic capacitors can also be used for CIN. Always
consult the manufacturer if there is any question.
ASchottkydiodeisagoodchoiceforlowforwarddropand
fast switching time. Remember to keep lead length short
and observe proper grounding to avoid ringing and
increased dissipation.
The benefit of the LTC3737 2-phase operation can be
calculated by using the equation above for the higher
power controller and then calculating the loss that would
have resulted if both controller channels switched on at
the same time. The total RMS power lost is lower when
both controllers are operating due to the reduced overlap
of current pulses required through the input capacitor’s
ESR. This is why the input capacitor’s requirement calcu-
lated above for the worst-case controller is adequate for
the dual controller design. Also, the input protection fuse
resistance, battery resistance, and PC board trace resis-
tance losses are also reduced due to the reduced peak
currents in a 2-phase system. The overall benefit of a
multiphase design will only be fully realized when the
source impedance of the power supply/battery is included
in the efficiency testing. The sources of the P-channel
MOSFETs should be placed within 1cm of each other and
share a common CIN(s). Separating the sourced and CIN
may produce undesirable voltage and current resonances
at VIN.
CIN and COUT Selection
The selection of CIN is simplified by the 2-phase architec-
ture and its impact on the worst-case RMS current drawn
through the input network (battery/fuse/capacitor). It can
be shown that the worst-case capacitor RMS current
occurs when only one controller is operating. The control-
ler with the highest VOUT • IOUT product needs to be used
in the formula below to determine the maximum RMS
capacitor current requirement. Increasing the output cur-
rent drawn from the other controller will actually decrease
the input RMS ripple current from its maximum value. The
out-of-phase technique typically reduces the input
capacitor’s RMS ripple current by a factor of 30% to 70%
when compared to a single phase power supply solution.
In continuous mode, the source current of the P-channel
MOSFET is a square wave of duty cycle (VOUT + VD)/
(VIN + VD). To prevent large voltage transients, a low ESR
capacitor sized for the maximum RMS current of one
channel must be used. The maximum RMS capacitor
current is given by:
A small (0.1µF to 1µF) bypass capacitor between the chip
VIN pin and ground, placed close to the LTC3737, is also
suggested. A 10Ω resistor placed between CIN and the VIN
pin provides further isolation between the two channels.
CIN Required IRMS
IMAX
V + VD
IN
≈
The selection of COUT is driven by the effective series
resistance (ESR). Typically, once the ESR requirement is
satisfied, the capacitance is adequate for filtering. The
output ripple (∆VOUT) is approximated by:
1/2
]
V
OUT + VD V – V
(
[
)(
)
IN OUT
This formula has a maximum at VIN = 2VOUT + VD, where
IRMS = IOUT/2. This simple worst-case condition is com-
monlyusedfordesignbecauseevensignificantdeviations
do not offer much relief. Note that capacitor manufactur-
ers’ ripple current ratings are often based on only 2000
hours of life. This makes it advisable to further derate the
capacitor or to choose a capacitor rated at a higher
temperature than required. Several capacitors may be
1
∆VOUT ≈IRIPPLE ESR +
8fCOUT
where f is the operating frequency, COUT is the output
capacitance and IRIPPLE is the ripple current in the induc-
tor. The output ripple is highest at maximum input voltage
since IRIPPLE increases with input voltage.
3737f
15
LTC3737
W U U
U
APPLICATIO S I FOR ATIO
Setting Output Voltage
During soft-start, the start-up of VOUT1 is controlled by
slowlyrampingthepositivereferencetotheerroramplifier
from 0V to 0.6V, allowing VOUT1 to rise smoothly from 0V
toitsfinalvalue. Thedefaultinternalsoft-starttimeis1ms.
This can be increased by placing a capacitor between the
RUN/SS pin and SGND. In this case, the soft start time will
be approximately:
The LTC3737 output voltages are each set by an external
feedback resistor divider carefully placed across the out-
put, as shown in Figure 6. The regulated output voltage is
determined by:
RB
VOUT = 0.6V • 1+
RA
600mV
t
SS1 = CSS
•
0.7µA
V
OUT
Tracking
R
B
1/2 LTC3737
The start-up of VOUT2 is controlled by the voltage on the
TRACK pin. Normally this pin is used to allow the start-up
of VOUT2 to track that of VOUT1 as shown qualitatively in
Figures 8a and 8b. When the voltage on the TRACK pin is
less than the internal 0.6V reference, the LTC3737 regu-
lates the VFB2 voltage to the TRACK pin voltage instead of
0.6V. The start-up of VOUT2 may ratiometrically track that
of VOUT1, according to a ratio set by a resistor divider
(Figure 8c):
V
FB
R
A
3737 F06
Figure 6. Setting Output Voltage
Run/Soft Start Function
The RUN/SS pin is a dual purpose pin that provides the
optional external soft-start function and a means to shut
down the LTC3737.
VOUT1
VOUT2 RTRACKA
R2A
R
TRACKA +RTRACKB
R2B +R2A
=
•
Pulling the RUN/SS pin below 0.65V puts the LTC3737
into a low quiescent current shutdown mode (IQ = 9µA). If
RUN/SS has been pulled all the way to ground, there will
beadelaybeforetheLTC3737comesoutofshutdownand
is given by:
For coincident tracking (VOUT1 = VOUT2 during start-up),
R2A = RTRACKA
R2B = RTRACKB
CSS
0.7µA
The ramp time for VOUT2 to rise from 0V to its final value
is:
tDELAY = 0.65V •
= 0.93s/µF •CSS
RTRACKA
R1A
R1A +R1B
TRACKA +RTRACKB
This pin can be driven directly from logic as shown in
Figure 7. Diode D1 in Figure 7 reduces the start delay but
allows CSS to ramp up slowly providing the soft-start
function. This diode (and capacitor) can be deleted if the
external soft-start is not needed.
t
SS2 = tSS1
•
•
R
V
OUT1
V
OUT2
LTC3737
R1B
R2B
V
FB1
V
FB2
3.3V OR 5V
RUN/SS
RUN/SS
R1A
R2A
D1
R
R
TRACKB
TRACK
C
SS
3737 F08a
C
SS
TRACKA
3737 F07
Figure 7. RUN/SS Pin Interfacing
Figure 8a. Using the TRACK Pin
3737f
16
LTC3737
W U U
APPLICATIO S I FOR ATIO
U
V
V
V
OUT1
OUT1
OUT2
V
OUT2
3737 F08b,c
TIME
TIME
(8b) Coincident Tracking
(8c) Ratiometric Tracking
Figures 8b and 8c. Two Different Modes of Output Voltage Tracking
within range of the LTC3737’s internal VCO, which is
nominally 200kHz to 1MHz. This is guaranteed over tem-
peratureandvariationstobebetween250kHzand850kHz.
A simplified block diagram is shown in Figure 10.
For coincident tracking,
VOUT2F
t
SS2 = tSS1 •
VOUT1F
where VOUT1F and VOUT2F are the final, regulated values of
VOUT1 and VOUT2. VOUT1 should always be greater than
VOUT2 when using the TRACK pin. If no tracking function
is desired, then the TRACK pin may be tied to VIN. How-
ever, in this situation there would be no (internal nor
1400
1200
1000
800
600
400
200
0
external) soft-start on VOUT2
.
Phase-Locked Loop and Frequency Synchronization
TheLTC3737hasaphase-lockedloop(PLL)comprisedof
an internal voltage controlled oscillator (VCO) and a phase
detector. This allows the turn-on of the external P-channel
MOSFET of controller 1 to be locked to the rising edge of
an external clock signal applied to the SYNC/MODE pin.
The turn-on of controller 2’s external P-channel MOSFET
is thus 180 degrees out of phase with the external clock.
The phase detector is an edge sensitive digital type that
provides zero degrees phase shift between the external
and internal oscillators. This type of phase detector does
not exhibit false lock to harmonics of the external clock.
0
0.5
1
1.5
2
2.4
PLLLPF PIN VOLTAGE (V)
3737 F09
Figure 9. Relationship Between Oscillator Frequency
and Voltage at the PLLLPF Pin
2.4V
R
LP
C
LP
PLLLPF
SYNC/
MODE
DIGITAL
PHASE/
FREQUENCY
DETECTOR
The output of the phase detector is a pair of complemen-
tary current sources that charge or discharge the external
filter network connected to the PLLLPF pin. The relation-
ship between the voltage on the PLLLPF pin and operating
frequency, when there is a clock signal applied to SYNC/
MODE, is shown in Figure 9 and specified in the electrical
characteristics table. Note that the LTC3737 can only be
synchronized to an external clock whose frequency is
EXTERNAL
OSCILLATOR
OSCILLATOR
3737 F08
Figure 10. Phase-Locked Loop Block Diagram
3737f
17
LTC3737
W U U
U
APPLICATIO S I FOR ATIO
V
OUT
If the external clock frequency is greater than the internal
oscillator’s frequency, fOSC, then current is sourced con-
tinuously from the phase detector output, pulling up the
PLLLPF pin. When the external clock frequency is less
than fOSC, current is sunk continuously, pulling down the
PLLLPFpin. Iftheexternalandinternalfrequenciesarethe
same but exhibit a phase difference, the current sources
turn on for an amount of time corresponding to the phase
difference. The voltage on the PLLLPF pin is adjusted until
the phase and frequency of the external oscillators are
identical. At the stable operating point, the phase detector
outputishighimpedanceandthefiltercapacitorCLP holds
the voltage.
1/2 LTC3737
R2
R1
D
D
+
FB1
I
V
FB
TH
FB2
3737 F11
Figure 11. Foldback Current Limiting
Low Supply Operation
Although the LTC3737 can function down to below 2.4V,
the maximum allowable output current is reduced as VIN
decreases below 3V. Figure 12 shows the amount of
changeasthesupplyisreduceddownto2.4V. Alsoshown
The loop filter components, CLP and RLP, smooth out the
current pulses from the phase detector and provide a
stable input to the voltage controlled oscillator. The filter
components CLP and RLP determine how fast the loop
acquires lock. Typically RLP = 10k and CLP is 2200pF to
0.01µF.
is the effect on VREF
.
105
V
REF
100
95
90
MAXIMUM
SENSE VOLTAGE
Typically, the external clock (on the SYNC/MODE pin)
input high level is 1.6V, while the input low level is 1.2V.
These levels are guaranteed to be TTL/CMOS compatible:
0.8V is guaranteed low, while 2.0V is guaranteed high.
85
80
75
Table 1 summarizes the different states in which the
PLLLPF pin can be used.
2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0
INPUT VOLTAGE (V)
3737 F12
Table 1
PLLLPF PIN
0V
SYNC/MODE PIN
DC Voltage
FREQUENCY
Figure 12. Line Regulation of VREF and Maximum Sense Voltage
300kHz
550kHz
Floating
DC Voltage
Minimum On-Time Considerations
V
DC Voltage
750kHz
IN
Minimumon-time,tON(MIN),isthesmallestamountoftime
that the LTC3737 is capable of turning the top P-channel
MOSFET on and then off. It is determined by internal
timing delays and the gate charge required to turn on the
top MOSFET. The minimum on-time for the LTC3737 is
typically about 250ns. Low duty cycle and high frequency
applications may approach the minimum on-time limit
and care should be taken to ensure that:
RC Loop Filter
Clock Signal
Phase-Locked to External Clock
Fault Condition: Short Circuit and Current Limit
To prevent excessive heating of the catch diode, foldback
current limiting can be added to reduce the current in
proportion to the severity of the fault.
Foldback current limiting is implemented by adding di-
odes DFB1 and DFB2 between the output and the ITH pin as
showninFigure11.Inahardshort(VOUT=0V),thecurrent
will be reduced to approximately 50% of the maximum
output current.
V
OUT + VD
tON(MIN)
<
fOSC • V + V
(
)
IN
D
3737f
18
LTC3737
W U U
APPLICATIO S I FOR ATIO
U
Ifthedutycyclefallsbelowwhatcanbeaccommodatedby
the minimum on-time, the LTC3737 will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple current and ripple voltage will increase.
5) Transition losses apply to the external MOSFET and
increase with higher operating frequencies and input
voltages. Transition losses can be estimated from:
Transition Loss = 2(VIN)2 • IO(MAX) • CRSS(f)
Efficiency Considerations
Other losses, including CIN and COUT ESR dissipative
lossesandinductorcorelosses,generallyaccountforless
than 2% total additional loss.
The efficiency of a switching regulator is equal to the
output power divided by the input power times 100%. It is
oftenusefultoanalyzeindividuallossestodeterminewhat
is limiting efficiency and which change would produce the
most improvement. Efficiency can be expressed as:
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, VOUT immediately shifts by an amount
equal to (∆ILOAD)(ESR), where ESR is the effective series
resistance of COUT. ∆ILOAD also begins to charge or dis-
chargeCOUT, whichgeneratesafeedbackerrorsignal. The
regulator loop then returns VOUT to its steady-state value.
Duringthisrecoverytime,VOUT canbemonitoredforover-
shoot or ringing. OPTI-LOOP® compensation allows the
transient response to be optimized over a wide range of
output capacitance and ESR values.
Efficiency = 100% - (L1 + L2 + L3 + …)
whereL1, L2, etc. aretheindividuallossesasapercentage
of input power.
Although all dissipative elements in the circuit produce
losses, five main sources usually account for most of the
losses in LTC3737 circuits: 1) LTC3737 DC bias current,
2) MOSFET gate charge current, 3) I2R losses, 4) voltage
drop of the output diode and 5) transition losses.
1) The VIN (pin) current is the DC supply current, given in
the electrical characteristics, that excludes MOSFET
driver currents. VIN current results in a small loss that
increases with VIN.
The ITH series RC-CC filter (see Functional Diagram) sets
the dominant pole-zero loop compensation. The ITH exter-
nal components shown in the Figure 1 circuit will provide
an adequate starting point for most applications. The
values can be modified slightly (from 0.2 to 5 times their
suggestedvalues)tooptimizetransientresponseoncethe
final PC layout is done and the particular output capacitor
type and value have been determined. The output capaci-
tors need to be decided upon because the various types
and values determine the loop feedback factor gain and
phase. Anoutputcurrentpulseof20%to100%offullload
current having a rise time of 1µs to 10µs will produce
outputvoltageandITH pinwaveformsthatwillgiveasense
of the overall loop stability. The gain of the loop will be
increased by increasing RC, and the bandwidth of the loop
will be increased by decreasing CC. The output voltage
settling behavior is related to the stability of the closed-
loopsystemandwilldemonstratetheactualoverallsupply
performance. For a detailed explanation of optimizing the
compensation components, including a review of control
loop theory, refer to Application Note 76.
2) MOSFETgatechargecurrentresultsfromswitchingthe
gate capacitance of the power MOSFET. Each time a
MOSFET gate is switched from low to high to low again,
a packet of charge dQ moves from PVIN to ground. The
resulting dQ/dt is a current out of PVIN, which is
typically much larger than the DC supply current. In
continuous mode, IGATECHG = f • QP.
3) I2R losses are calculated from the DC resistances of the
MOSFET, inductor and sense resistor. In continuous
mode, the average output current flows through L but
is “chopped” between the P-channel MOSFET and the
output diode. The MOSFET RDS(ON) multiplied by duty
cycle can be summed with the resistance of L to obtain
I2R losses.
4) Theoutputdiodeisamajorsourceofpowerlossathigh
currents and is worse at high input voltages. The diode
loss is calculated by multiplying the forward voltage
times the load current times the diode duty cycle.
OPTI-LOOP is a registered trademark of Linear Technology Corporation.
3737f
19
LTC3737
W U U
U
APPLICATIO S I FOR ATIO
A second, more severe transient is caused by switching in
loads with large (>1µF) supply bypass capacitors. The
dischargedbypasscapacitorsareeffectivelyputinparallel
with COUT, causing a rapid drop in VOUT. No regulator can
deliver enough current to prevent this problem if the load
switch resistance is low and it is driven quickly. The only
solution is to limit the rise time of the switch drive so that
the load rise time is limited to approximately (25)(CLOAD).
Thus a 10µF capacitor would require a 250µs rise time,
limiting the charging current to about 200mA.
PC Board Layout Checklist
When laying out the printed circuit board, use the follow-
ing checklist to ensure proper operation of the LTC3737.
•
The power loop (input capacitor, MOSFET, inductor,
outputdiode, outputcapacitor)ofeachchannelshould
be as small as possible and isolated as much as
possible from the other channel’s power loop. It is
better to have two separate, smaller valued input
capacitors (e.g., two 10µF—one for each channel)
than it is to have a single larger valued capacitor (e.g.,
one 22µF) that the channels share with a common
connection.
Design Example
As a design example, assume VIN will be operating from a
maximum of 4.2V down to a minimum of 2.7V (powered
by a single lithium-ion battery). Load current requirement
is a maximum of 2.5A, but most of the time it will be in a
standby mode requiring only 2mA. Efficiency at both low
andhighloadcurrentsisimportant. BurstModeoperation
at light loads is desired. Output voltage is 2.5V. The IPRG
pin will be tied to VIN, so the maximum current sense
threshold ∆VSENSE(MAX) is approximately 204mV.
• The signal and power grounds should be kept separate.
The signal ground consists of the feedback resistor
dividers, ITH compensation networks and the SGND
pin.
The power grounds consist of the (–) terminal of the
input and output capacitors, the anode of the Schottky
diodes and the PGND pins. Each channel should have
its own power ground for its power loop as described
above. The power grounds for the two channels should
connect together at a common point. It is most impor-
tant to keep the ground paths with high switching
currents away from each other.
V
OUT + VD
Maximum Duty Cycle =
= 93%
VIN(MIN) + VD
From Figure 2, SF = 57%.
• Put the feedback resistors close to the VFB pins. The ITH
compensationcomponentsshouldalsobeverycloseto
the LTC3737.
∆VSENSE(MAX)
IOUT(MAX) • ρT
5
6
R
DS(ON)(MAX) = • 0.9 • SF •
• The current sense traces (SENSE+ and SENSE–/SW)
should be Kelvin connections right at the P-channel
MOSFET source and drain.
= 0.027Ω
A 0.025Ω Si3473DV P-channel MOSFET is close to this
value.
• Keep the switch nodes (SW1, SW2) and the gate driver
nodes (PGATE1, PGATE2) away from the small-signal
components, especially the opposite channel’s feed-
back resistors, ITH compensation components and the
current sense pins (SENSE+ and SENSE–/SW).
The PLLLPF pin will be left floating, so the LTC3737 will
operate at its default frequency of 550kHz. For continuous
Burst Mode operation, the required minimum inductor
value is:
4.2V – 2.5V
0.051V
2.5V + 0.3V
4.2V + 0.3V
LMIN
=
= 1.40µH
550kHz
0.025Ω
3737f
20
LTC3737
W U U
APPLICATIO S I FOR ATIO
U
100pF
V
IN
5V
220pF
L1
V
2.5V
5A
15k
24
OUT1
187k
59k
1.5µH
M1
118k
59k
1
22
21
+
20 19
NC
IN1
V
I
SW1 SENSE1 PV
FB1 TH1
C3
+
C1
150µF
23
2
18
17
16
15
14
13
22µF
×2
D1
IPRG1
IPRG2
PLLLPF
SGND
SYNC/MODE
PGATE1
PGND
3
1µF
LTC3737EUF
4
PGATE2
RUN/SS
10Ω
5
C2
V
IN
D2
+
150µF
1M
9
PGOOD
NC
+
59k
V
I
TRACK SW2 SENSE2 PV
FB2 TH2
IN2
12
L2
1.5µH
7
8
6
10
11
V
1.8V
5A
OUT2
220pF
M2
15k
118k
C
SS
10nF
3737 F13
100pF
C1, C2: SANYO 4TPB150MC
C3: TAIYO YUDEN LMK325BJ106K-T
D1, D2: SBM540
L1, L2: VISHAY IHLP-2525CZ-01-1.5
M1, M2: FDC602P
Figure 13. 2-Phase, 550kHz, Dual Output Step-Down DC/DC Converter
U
TYPICAL APPLICATIO S
2-Phase, 750kHz, Burst Mode Dual Output Step-Down DC/DC Converter
100pF
220pF
V
IN
5V
L1
V
2.5V
3A
15k
24
OUT1
187k
59k
2.2µH
M1
118k
59k
1
22
21
+
20 19
NC
IN1
V
I
SW1 SENSE1 PV
FB1 TH1
C3
+
C1
47µF
10µF
×2
23
2
18
17
16
15
14
13
D1
IPRG1
IPRG2
PLLLPF
SGND
SYNC/MODE
PGATE1
PGND
3
1µF
LTC3737EUF
4
PGATE2
RUN/SS
10Ω
5
C2
47µF
V
IN
D2
+
1M
9
PGOOD
NC
+
59k
V
I
TRACK SW2 SENSE2 PV
FB2 TH2
IN2
12
L2
2.2µH
7
8
6
10
11
V
1.8V
3A
OUT2
220pF
M2
15k
118k
3737 TA01
100pF
C1, C2: SANYO 6TPA47M
C3: TAIYO YUDEN LMK325BJ106K-T
D1, D2: IR 10BQ015
L1, L2: COILCRAFT D03316P-22
M1, M2: Si9803DY
3737f
21
LTC3737
TYPICAL APPLICATIO S
U
2-Phase, Synchronizable Dual Output Step-Down DC/DC Converter
100pF
220pF
V
IN
3.3V
L1
V
2.5V
2 A
15k
24
OUT1
187k
59k
2.2µH
M1
118k
59k
1
22
21
+
20 19
NC
IN1
V
I
SW1 SENSE1 PV
FB1 TH1
C3
+
C1
47µF
23
2
18
17
16
15
14
13
10µF
×2
D1
IPRG1
IPRG2
PLLLPF
SGND
SYNC/MODE
PGATE1
PGND
10nF
10k
3
4
5
9
LTC3737EUF
PGATE2
RUN/SS
10Ω
1µF
C2
47µF
V
IN
D2
+
1M
PGOOD
NC
+
59k
V
I
TRACK SW2 SENSE2 PV
FB2 TH2
IN2
12
L2
2.2µH
7
8
6
10
11
V
1.8V
2A
OUT2
220pF
100pF
M2
15k
118k
3737 TA02
C1, C2: SANYO 6TPA47M
C3: TAIYO YUDEN LMK325BJ106K-T
D1, D2: CENTRAL CMSH1-20ML
L1, L2: COILCRAFT D03316P-22
M1, M2: Si9803DY
2-Phase, 550kHz, Single Output Step-Down DC/DC Converter (3.3VIN to 1.8VOUT at 8A)
V
IN
3.3V
220pF
L1
1.5µH
15k
V
1.8V
8A
OUT
M1
24
1
22
21
+
20 19
NC
IN1
V
I
SW1 SENSE1 PV
FB1 TH1
C3
10µF
×2
+
C1
23
2
18
17
16
15
14
13
D1
150µF
IPRG1
IPRG2
PLLLPF
SGND
SYNC/MODE
PGATE1
PGND
3
LTC3737EUF
4
PGATE2
RUN/SS
10Ω
1µF
5
9
C2
150µF
V
IN
D2
+
1M
PGOOD
NC
+
59k
V
I
TRACK SW2 SENSE2 PV
FB2 TH2
IN2
12
L2
1.5µH
7
8
6
10
11
220pF
M2
118k
59k
118k
3737 TA04
C1, C2: SANYO 4TPR150MC
C3: TAIYO YUDEN LMK325BJ106K-T
D1, D2: SBM540
L1, L2: VISHAY IHLP-2525CZ-01-1.5
M1, M2: FDC602P
3737f
22
LTC3737
U
PACKAGE DESCRIPTIO
GN Package
24-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.337 – .344*
(8.560 – 8.738)
.045 ±.005
.033
(0.838)
REF
24 23 22 21 20 19 18 17 16 15 14 13
.254 MIN
.150 – .165
.229 – .244
.150 – .157**
(5.817 – 6.198)
(3.810 – 3.988)
.0165 ±.0015
.0250 BSC
1
2
3
4
5
6
7
8
9 10 11 12
RECOMMENDED SOLDER PAD LAYOUT
.015 ± .004
(0.38 ± 0.10)
.0532 – .0688
(1.35 – 1.75)
.004 – .0098
(0.102 – 0.249)
× 45°
.0075 – .0098
(0.19 – 0.25)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
.008 – .012
.0250
(0.635)
BSC
GN24 (SSOP) 0204
(0.203 – 0.305)
TYP
NOTE:
1. CONTROLLING DIMENSION: INCHES
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
3. DRAWING NOT TO SCALE
UF Package
24-Lead Plastic QFN (4mm × 4mm)
(Reference LTC DWG # 05-08-1697)
BOTTOM VIEW—EXPOSED PAD
0.23 TYP
(4 SIDES)
R = 0.115
TYP
0.75 ± 0.05
4.00 ± 0.10
(4 SIDES)
23 24
0.70 ±0.05
PIN 1
TOP MARK
(NOTE 6)
0.38 ± 0.10
1
2
4.50 ± 0.05
3.10 ± 0.05
2.45 ± 0.05
(4 SIDES)
2.45 ± 0.10
(4-SIDES)
PACKAGE
OUTLINE
(UF24) QFN 1103
0.25 ± 0.05
0.50 BSC
0.200 REF
0.25 ±0.05
0.50 BSC
0.00 – 0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT
3737f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
23
LTC3737
U
TYPICAL APPLICATIO
2-Phase, 300kHz, Resistor Sensing, Dual Output Step-Down DC/DC Converter
100pF
220pF
V
IN
2.75V TO 9.8V
L1
V
2.5V
2A
15k
24
OUT1
187k
59k
2.2µH
M1
1
22
21
+
20 19
NC
IN1
R1
0.03Ω
V
I
SW1 SENSE1 PV
FB1 TH1
C3
+
C1
47µF
10µF
×2
23
2
18
D1
IPRG1
IPRG2
PLLLPF
SGND
SYNC/MODE
PGATE1
PGND
17
16
15
14
13
3
LTC3737EUF
1µF
10Ω
1M
4
PGATE2
RUN/SS
5
C2
47µF
V
D2
IN
+
9
PGOOD
NC
+
59k
V
I
TRACK SW2 SENSE2 PV
FB2 TH2
IN2
12
L2
2.2µH
R2
7
8
6
10
11
0.03Ω
V
1.8V
2A
OUT2
220pF
100pF
M2
15k
118k
3737 TA03
C1, C2: SANYO 6TPA47M
L1, L2: COILCRAFT D03316P-22
C3: TAIYO YUDEN LMK325BJ106K-T M1, M2: Si3867DV
D1, D2: CENTRAL CMSH1-20ML
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1628/LTC3728
Dual High Efficiency, 2-Phase Synchronous
Step Down Controllers
Constant Frequency, Standby, 5V and 3.3V LDOs, V to 36V,
IN
28-Lead SSOP
LTC1629/LTC3729
20A TO 200A PolyPhaseTM High Efficiency Controllers
Expandable Up to 12 Phases, No Heat Sinks, V to 36V,
IN
28-Lead SSOP
LTC1702A
LTC1735
No R
TM 2-Phase Dual Synchronous Controller
550kHz, No Sense Resistor, GN24, V to 7V
SENSE
IN
High Efficiency Synchronous Step-Down Controller
Burst Mode Operation, 16-Pin Narrow SSOP, Fault Protection,
3.5V ≤ V ≤ 36V
IN
LTC1772
Constant Frequency Current Mode Step-Down
DC/DC Controller
2.5V ≤ V ≤ 9.8V, I
Up to 4A, SOT-23 Package, 550kHz
IN
OUT
LTC1773
LTC1778
Synchronous Step-Down Controller
2.65V ≤ V ≤ 8.5V, I
Up to 4A, 10-Lead MSOP
IN
OUT
No R
Synchronous Step-Down Controller
Current Mode Operation Without Sense Resistor,
Fast Transient Response, 4V ≤ V ≤ 36V
SENSE
IN
LTC1872
LTC1929
Constant Frequency Current Mode Step-Up Controller
2.5V ≤ V ≤ 9.8V, SOT-23 Package, 550kHz
IN
Constant Frequency Current Mode 2-Phase
Synchronous Controller
Up to 42A, No Heat Sink, 3.5V ≤ V ≤ 36V
IN
LTC3411
LTC3412
1.25A (I ), 4MHz, Synchronous Step-Down DC/DC Converter
95% Efficiency, V : 2.5V to 5.5V, V
SD
= 0.8V, I = 60µA,
Q
OUT
IN
OUT
OUT
I
= <1µA, MS Package
2.5A (I ), 4MHz, Synchronous Step-Down DC/DC Converter
95% Efficiency, V : 2.5V to 5.5V, V
= 0.8V, I = 60µA,
Q
OUT
IN
I
= <1µA, TSSOP-16E Package
SD
LTC3700
LTC3701
LTC3708
Constant Frequency Step-Down Controller with LDO Regulator
2-Phase, Low Input Voltage Dual Step-Down DC/DC Controller
2-Phase, Dual Synchronous Controller with Output Tracking
2.65≤ V ≤ 9.8V, 550kHz, 10-Lead SSOP
IN
2.5V ≤ V ≤ 9.8V, 550kHz, PGOOD, PLL, 16-Lead SSOP
IN
Constant On-Time Dual Controller, V Up to 36V, Very Low
IN
Duty Cycle Operation, 5mm × 5mm QFN Package
LTC3736
2-Phase, Dual Synchronous Controller with Output Tracking
2.75V ≤ V ≤ 9.8V, 0.6V ≤ V
≤ V , 4mm × 4mm QFN
OUT IN
IN
PolyPhase and No R
are trademarks of Linear Technology Corporation.
SENSE
3737f
LT/TP 0404 1K • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
24
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
LINEAR TECHNOLOGY CORPORATION 2004
相关型号:
LTC3737EUF#TR
LTC3737 - Dual 2-Phase, No RSENSE DC/DC Controller with Output Tracking; Package: QFN; Pins: 24; Temperature Range: -40°C to 85°C
Linear
LTC3737EUF#TRPBF
LTC3737 - Dual 2-Phase, No RSENSE DC/DC Controller with Output Tracking; Package: QFN; Pins: 24; Temperature Range: -40°C to 85°C
Linear
LTC3738CUHF#PBF
LTC3738 - 3-Phase Buck Controller for Intel VRM9/VRM10 with Active Voltage Positioning; Package: QFN; Pins: 38; Temperature Range: 0°C to 70°C
Linear
LTC3738CUHF#TR
LTC3738 - 3-Phase Buck Controller for Intel VRM9/VRM10 with Active Voltage Positioning; Package: QFN; Pins: 38; Temperature Range: 0°C to 70°C
Linear
LTC3765EMSE#TRPBF
LTC3765 - Active Clamp Forward Controller and Gate Driver; Package: MSOP; Pins: 16; Temperature Range: -40°C to 85°C
Linear
LTC3765MPMSE#PBF
LTC3765 - Active Clamp Forward Controller and Gate Driver; Package: MSOP; Pins: 16; Temperature Range: -55°C to 125°C
Linear
LTC3765MPMSE#TRPBF
LTC3765 - Active Clamp Forward Controller and Gate Driver; Package: MSOP; Pins: 16; Temperature Range: -55°C to 125°C
Linear
©2020 ICPDF网 联系我们和版权申明