1-91047-6 [MACOM]

Reasons for reissue of this instruction sheet are provided in Section 6, REVISION SUMMARY.;


型号：	1-91047-6
厂家：	Tyco Electronics
描述：	Reasons for reissue of this instruction sheet are provided in Section 6, REVISION SUMMARY.
文件：	总2页 (文件大小：216K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

408-7384

Extraction Tools 91047-[ ]

11 MAY 10 Rev A

Outer Edge of Connector Housing

(Single-Row Connector Shown)

Locking Lance Slot

Extraction Tool

(Ref)

Flexible Flat Cable

(FFC)

Locking Lance

Blade

Figure 1

1. INTRODUCTION

EXTRACTION TOOL

Extraction Tools 91047-[ ] are designed to extract

flexible flat cable (FFC) contacts from FFC pin,

receptacle, and edge connectors with end entrance

locking lance slots (reference part number 86670-8).

Read these instructions thoroughly before removing

any contacts.

PART NUMBER

0-91047-1

0-91047-2

0-91047-3

0-91047-5

1-91047-0

1-91047-2

1-91047-4

1-91047-5

1-91047-6

1-91047-8

1-91047-9

2-91047-6

NUMBER OF BLADES

For connectors with side entrance locking lance slots,

refer to 408-7916 for Tool 91200-[ ].

Dimensions in this instruction sheet are in

millimeters [with inches in brackets]. Figures are

NOTE

not drawn to scale.

Reasons for reissue of this instruction sheet are

provided in Section 6, REVISION SUMMARY.

2. DESCRIPTION

Figure 2

Each tool features a specific number of tool blades

that release the contact locking lances of the

connector. See Figure 1. The number of tool blades

must match the number of cavities in one row of the

connector.

Proceed as follows:

1. Align the tool blades with the locking lance

slots located between the contacts and outer

edge of the housing as shown in Figure 1.

All contact locking lances must be released

CAUTION

simultaneously; otherwise, damage to the

connector, contacts, or cable may result.

2. Simultaneously insert all tool blades straight

into the connector until the tool bottoms. Only the

radius between the tool blades should be visible

when the tool is properly seated. See Figure 3.

3. EXTRACTION PROCEDURE

3. Holding the tool and connector in one hand,

carefully pull on the cable. A slight side-to-side

motion may be used to ease contact extraction.

Refer to Figure 2, and ensure that the number of

blades of the extraction tool matches the number of

contact cavities in one row of the connector.

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

1 of 2

TE logo and Tyco Electronics are trademarks.

*Trademark. Other products, logos, and company names might be trademarks of their respective owners.

LOC B

408-7384

It is recommended that the tool be inspected

immediately when received and at regularly

scheduled intervals.

Tool Fully Inserted

into Connector

Radius Between

Tool Blades

Visible

It is recommended that the tool be stored in a clean,

dry place and cleaned with a soft, lint-free cloth.

5. REPLACEMENT AND REPAIR

The tool is not repairable and should be replaced

when worn or damaged. Additional tools can be

purchased from:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

Figure 3

HARRISBURG PA 17105-3608

Excessive or improper force may cause damage

to the contacts or cable.

CAUTION

6. REVISION SUMMARY

Revisions to this instruction sheet include:

• Updated instruction sheet to corporate

requirements

4. After the cable and all of the contacts have

been completely extracted, remove the tool from

the connector.

• Removed obsolete extraction tools

• Replaced connector series part numbers with

4. MAINTENANCE AND INSPECTION

reference part number

To ensure proper operation, the tool should conform

to the dimensions provided in Figure 4.

6.73

[.265]

2.54 [1.00]

0.38 [.015]

0.76 [.030]

32.51

[1.280]

Tool Number

Marked Here

2.29 [.09]

EXTRACTION TOOL

DIMENSION

PART NUMBER

0-91047-1

0-91047-2

0-91047-3

0-91047-5

1-91047-0

1-91047-2

20.32 [.800]

45.72 [1.800]

71.12 [2.800]

48.26 [1.900]

22.86 [.900]

86.36 [3.400]

21.08 [.830]

46.48 [1.830]

71.88 [2.830]

49.02 [1.930]

23.62 [.930]

87.12 [3.430]

1-91047-4

1-91047-5

1-91047-6

1-91047-8

1-91047-9

2-91047-6

27.94 [1.100]

33.02 [1.300]

35.56 [1.400]

10.16 [.400]

5.08 [.200]

28.70 [1.130]

33.78 [1.330]

36.32 [1.430]

10.92 [.430]

5.84 [.230]

17.78 [.700]

18.54 [.730]

Figure 4

2 of 2

Rev A

相关型号：