91319--3 [MACOM]

Backplane Receptacle Connector Assemblies;


型号：	91319--3
厂家：	Tyco Electronics
描述：	Backplane Receptacle Connector Assemblies
文件：	总3页 (文件大小：87K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

Seating Tools 91318-[ ], 91319-[ ], and 91320-[ ]

For Z-PACK* HS3 and Z-PACK 12-Row

Backplane Receptacle Connector Assemblies

408-4571

12 MAR 10 Rev A

Seating Tool

ACTION PIN*

Contact

Typical Z--PACK HS3

Backplane Receptacle

Connector Assembly (Ref)

CONNECTOR

SEATING

TOOL

ROWS

POSITIONS

72 and 144

288

91318--1

91318--2

91318--3

91319--1

91319--2

91319--3

91320--1

91320--2

91320--3

Cut to Length

50 and 100

200

Printed Circuit (PC)

Board (Ref)

Cut to Length

30 and 60

120

PC Board Support Fixture

(Customer Supplied)

Cut to Length

Figure 1

1. INTRODUCTION

2. DESCRIPTION

Seating Tools 91318--[ ] are used to seat Z--PACK

12--row backplane receptacle connectors and Seating

Tools 91319--[ ] and 91320--[ ] are used to seat

Z--PACK HS3 backplane receptacle connectors. The

connectors have ACTION PIN contacts to allow

solderless pc board installation.

Each seating tool is a one--piece design. During

seating, the seating tool covers the connector and

presses on the top surface of the connector when the

applicator ram applies force to the seating tool.

3. REQUIREMENTS

All dimensions on this instruction sheet are in

metric units [with U.S. customary units in

brackets]. Figures are not drawn to scale.

NOTE

3.1. PC Board Support Fixture (Customer Supplied)

A pc board support must be used to provide proper

support for the pc board and alignment of the seating

tool to the connector contacts and to protect the pc

board and connector from damage. Design the pc

board support fixture using the recommendations in

instruction sheet 408--6927.

Read these instructions and understand them before

using the seating tools.

Reasons for reissue of this instruction sheet are

provided in Section 7, REVISION SUMMARY.

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

E2010 Tyco Electronics Corporation, Harrisburg, PA

1 of 3

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

LOC B

*Trademark. Other products, logos, and company names used are the property of their respective owners.

408-4571

Seating Tools 91318-[ ], 91319-[ ], and 91320-[ ]

3.2. Application Tooling

meets the seating tool. Verify the alignment of the

pc board support fixture, pc board, connector, and

seating tool.

Power for the seating tool must be provided by a

machine capable of supplying a downward force of

89 Newtons (N) [20 lb] per contact. Manual Electric

Servo Press (MEP 6T) 2--1399500--5 and Bench Top

Electric Servo Presses (BMEP 3T) 1--1399400--5 and

(BMEP 5T) 2--1399401--4 are available for this

seating tool. For information on the presses, visit the

press--fit assembly equipment website at

Damage to the pc board, seating tool, or

connector may occur if seating height is

improperly set, if the pc board is not properly

positioned with the seating tool, or if the seating

tool is not properly seated on the connector

before cycling the applicator ram.

CAUTION

http://tooling.tycoelectronics.com/pressfit.asp.

6. Cycle the applicator ram according to

instructions for the application tooling.

4. SEATING

7. Remove the pc board with the seated connector,

and check the connector for proper seating

according to the following:

1. Set seating height to the dimension shown in

Figure 2 (applicator shut height will equal the

seating height PLUS the combined thicknesses of

the pc board, and pc board support fixture).

a. the widest section of each contact is inside its

intended pc board hole

2. Position the connector onto the pc board so that

the contacts are properly aligned with the holes in

the pc board and the holes or slots in the pc board

support fixture. See Figure 2.

b. the connector is seated on the pc board with

the seating height given in Figure 2.

For detailed inspection requirements of the

seated connector assembly, refer to Application

Specification 114--13020.

NOTE

3. Sit the connector onto the pc board until the tips

of the contacts are resting securely on, but have

not fully entered, the holes in the pc board.

4. Position the seating tool onto the connector with

the slanted surface oriented as shown in Figure 2.

A damage connector should not be used. If a

damaged connector is evident, it should be

removed from the pc board and replaced with a

new one.

CAUTION

5. Center the seating tool and connector under the

applicator ram, and slowly lower the ram until it just

View After Seating

Applicator Ram

(Fully Down)

Seating Tool Centered

Under Applicator Ram and

Bottomed on Connector

Seating Height

(Connector Seated)

38.1 [1.50]

Applicator

Shut Height

(Ram Down)

PC Board

Contacts in PC Board Holes

and Holes or Grooves in

PC Board Support Fixture

(Customer Supplied)

Figure 2

2 of 3

Rev A

Tyco Electronics Corporation

408-4571

Seating Tools 91318-[ ], 91319-[ ], and 91320-[ ]

5. MAINTENANCE AND INSPECTION

5.1. Initial Inspection

It is recommended that the seating tool be inspected

using Figure 3 immediately upon arrival in your facility

to ensure that it has not been damaged during

shipment.

5.2. Daily Maintenance

DIMENSION

SEATING TOOL

It is recommended that each operator be made aware

of, and responsible for, the following steps of daily

maintenance:

91318--1

91318--2

91318--3

91319--1

91319--2

91319--3

91320--1

91320--2

91320--3

23.88 [.940]

47.75 [1.88]

95.50 [3.76]

24.89 [.980]

49.78 [1.96]

149.35[5.88]

24.89 [.980]

49.78 [1.96]

248.92 [9.80]

44.45 [1.75] 26.97 [1.062]

1. Remove dust, moisture, and other contaminants

with a clean, soft brush, or lint--free cloth. Do NOT

use objects that could damage the tool or any of its

components.

2. Ensure that the screws are in place and

secured.

38.10 [1.50]

28.70 [1.13]

25.40 [1.00]

28.44 [1.12]

3. When the tool is not in use, store it in a clean,

dry area.

5.3. Periodic Inspection

Regular inspections should be performed by quality

control personnel. A record of scheduled inspections

should remain with the tool or be supplied to

Figure 3

supervisory personnel responsible for the tool. The

inspection frequency should be based on the amount

of use, working conditions, operator training and skill,

and established company standards.

7. REVISION SUMMARY

Revisions to this instruction sheet include:

S Updated instruction sheet to corporate

requirements

S Removed references to support anvil

S Changed Paragraph 3.2

S Replaced Step 7, added CAUTION, and added

NOTE to Section 4

S Removed phone number for customer repair

service

6. REPLACEMENT

The seating tool is not repairable. Order replacement

seating tools through your representative, or call

1--800--526--5142, or send a facsimile of your

purchase order to 1--717--986--7605 or write to:

CUSTOMER SERVICE (38 -35)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105--3608

Rev A

3 of 3

Tyco Electronics Corporation

相关型号：