MT6203-HRG-A [MARKTECH]
3.0mm ROUND BI- POLAR LAMP (3LEADS); 3.0毫米ROUND双极LAMP （ 3LEADS ）
| 型号： | MT6203-HRG-A |
| 厂家： | 
MARKTECH CORPORATE |
| 描述： | 3.0mm ROUND BI- POLAR LAMP (3LEADS) |
| 文件： | 总6页 (文件大小：139K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
3Northway Lane North Latham,New York 12110.
Tollfree:1.800.984.5337
Phone:1.518.956.2980
Fax:1.518.785.4725
Http://www.marktechopto.com
SPECIFICATION
PART NO. : MT6203-HRG-A
3.0mm ROUND BI- POLAR LAMP (3LEADS)
ATTENTION
OBSERVE PRECAUTION
FOR HANDLING
ELECTRO STATIC
SENSITIVE
DEVICES
3.0mm ROUND BI- POLAR
LAMP (3LEADS)
MT6203-HRG-A
Description
This green and orange bi-color lamp is made with GaP/GaP green chip,
GaAsP/GaP orange chip and white diffused epoxy resin.
GREEN
ANODE
ORANGE
ANODE
COMMON
CATHODE
Notes:
1. All dimensions are in mm.
2. Tolerance is ± 0.25mm unless otherwise noted.
Description
LED Chip
Part No.
Lens Color
Material
Emitting Color
GaP/GaP
Green
MT6203-HRG-A
White diffused
GaAsP/GaP
Orange
VER.: 01 Date: 2007/11/06 Page: 1/5
3.0mm ROUND BI- POLAR
LAMP (3LEADS)
MT6203-HRG-A
Absolute Maximum Ratings at Ta=25℃
Parameter
Symbol
Rating
Unit
Power Dissipation
PD
VR
78
5
mW
V
Reverse Voltage
D.C. Forward Current
If
30
mA
μA
mA
℃
Reverse (Leakage) Current
Peak Current(1/10Duty Cycle,0.1ms Pulse Width.)
Operating Temperature Range
Storage Temperature Range
Ir
100
If(Peak)
Topr
Tstg
100
-40 to +95
-40 to +100
℃
Dip Soldering : 260℃for 5 sec.
Hand Soldering : 350℃for 3 sec.
Soldering Temperature(1.6mm from body)
Tsol
Electrical and Optical Characteristics:
Green
Parameter
Symbol
Condition
If=20mA
If=20mA
If=20mA
If=20mA
Vr=5V
Min.
Typ. Max. Unit
Luminous Intensity
IV
Vf
9.0
20.0
2.1
mcd
V
Forward Voltage
2.6
Peak Wavelength
λp
567
572
nm
nm
µA
deg
nm
Dominant Wavelength
Reverse (Leakage) Current
Viewing Angle
λd
Ir
100
2θ1/2
If=20mA
If=20mA
70
30
Spectrum Line Halfwidth
∆λ
Notes:1. The datas tested by IS tester.
2. Customer’s special requirements are also welcome.
VER.: 01 Date: 2007/11/06 Page: 2/5
3.0mm ROUND BI- POLAR
LAMP (3LEADS)
MT6203-HRG-A
Absolute Maximum Ratings at Ta=25℃
Parameter
Symbol
Rating
Unit
Power Dissipation
PD
VR
78
5
mW
V
Reverse Voltage
D.C. Forward Current
If
30
mA
μA
mA
℃
Reverse (Leakage) Current
Peak Current(1/10Duty Cycle,0.1ms Pulse Width.)
Operating Temperature Range
Storage Temperature Range
Ir
100
If(Peak)
Topr
Tstg
100
-40 to +95
-40 to +100
℃
Dip Soldering : 260℃for 5 sec.
Hand Soldering : 350℃for 3 sec.
Soldering Temperature(1.6mm from body)
Tsol
Electrical and Optical Characteristics:
Orange
Parameter
Symbol
Condition
If=20mA
If=20mA
If=20mA
If=20mA
Vr=5V
Min.
Typ. Max. Unit
Luminous Intensity
IV
Vf
9.0
20.0
2.1
mcd
V
Forward Voltage
2.6
Peak Wavelength
λp
642
629
nm
nm
µA
deg
nm
Dominant Wavelength
Reverse (Leakage) Current
Viewing Angle
λd
Ir
100
2θ1/2
If=20mA
If=20mA
70
35
Spectrum Line Halfwidth
∆λ
Notes:1. The datas tested by IS tester.
2. Customer’s special requirements are also welcome.
VER.: 01 Date: 2007/11/06 Page: 3/5
3.0mm ROUND BI- POLAR
LAMP (3LEADS)
MT6203-HRG-A
Typical Electrical / Optical Characteristics Curves :
50
40
50.0
40.0
30
20
10
30.0
20.0
10.0
0
20.0
Forward Current (mA)
10.0
0.0
30.0
1.2
1.6
2.0
2.4
2.8
3.2
Applied Voltage (V)
FORWARD CURRENT VS. LUMINOUS INTENSITY
FORWARD CURRENT VS.APPLIED VOLTAGE
20°
0°
10°
50
40
30°
40°
30
20
10
1.0
0.9
0.8
50°
60°
70°
80°
90°
0.7
0
20
40
60
80
100
0.5
0.2
0.4
0.3
0.1
0.6
Temperature(。C)
RADIATION DIAGRAM
FORWARD CURRENT VS. AMBIENT TEMPERATURE
VER.: 01 Date: 2007/11/06 Page: 4/5
3.0mm ROUND BI- POLAR
LAMP (3LEADS)
MT6203-HRG-A
Precautions:
TAKE NOTE OF THE FOLLOWING IN USE OF LED
1. Temperature in use
Since the light generated inside the LED needs to be emitted to outside efficiently, a resin with
high light transparency is used; therefore, additives to improve the heat resistance or moisture
resistance (silica gel , etc) which are used for semiconductor products such as transistors
cannot be added to the resin.
Consequently, the heat resistant ability of the resin used for LED is usually low; therefore,
please be careful on the following during use.
Avoid applying external force, stress, and excessive vibration to the resins and terminals at
high temperature. The glass transition temperature of epoxy resin used for the LED is
approximately 120-130℃.
At a temperature exceeding this limit, the coefficient of liner expansion of the resin doubles or
more compared to that at normal temperature and the resin is softened.
If external force or stress is applied at that time, it may cause a wire rupture.
2. Soldering
Please be careful on the following at soldering.
After soldering, avoided applying external force, stress, and excessive vibration until the
products go to cooling process (normal temperature), <Same for products with terminal leads>
(1)
Soldering measurements:
Distance between melted solder side to bottom of resin shall be 1.6mm or longer.
(2) Solder dip: Preheat: 90℃ max. (Backside of PCB), Within 60 seconds
Solder bath: 260±5℃ (Solder temperature), Within 5 seconds
(3)
Soldering iron : 350℃ max. (Temperature of soldering iron tip), Within 3 seconds
3. Insertion
Pitch of the LED leads and pitch of mounting holes need to be same
4. Others
Since the heat resistant ability of the LED resin is low, SMD components are used on the same
PCB, please mount the LED after adhesive baking process for SMD components. In case
adhesive baking is done after LED lamp insertion due to a production process reason, make
sure not to apply external force, stress, and excessive vibration to the LED and follow the
conditions below.
Baking temperature: 120℃ max. Baking time: Within 60 seconds
If soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down
the LED to normal temperature.
VER.: 01 Date: 2007/11/06 Page: 5/5
相关型号：
©2020 ICPDF网 联系我们和版权申明