DS2119ME+T&R [MAXIM]

Ultra3 LVD/SE SCSI Terminator;


型号：	DS2119ME+T&R
厂家：	MAXIM INTEGRATED PRODUCTS
描述：	Ultra3 LVD/SE SCSI Terminator
文件：	总9页 (文件大小：308K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

DS2119M

Ultra3 LVD/SE SCSI Terminator

www.maxim-ic.com

PIN CONFIGURATION

FEATURES

ꢀ Fully Compliant with SCSI SPI-2, SPI-3,

SPI-4, Ultra160, and Ultra320

TPWR

R9N

VREF

RIP

ꢀ Provides Multimode Low-Voltage

Differential/Single-Ended (LVD/SE)

Termination for Nine Signal Line Pairs

DS2119M

RIN

R2P

R9P

R2N

R8N

HS GND

R3P

R8P

ꢀ Autoselection of LVD or SE Termination

HS GND

R7N

ꢀ 5% Tolerance on SE and LVD Termination

R3N

Resistance

R4P

R7P

R4N

R6N

ꢀ Low Power-Down Capacitance of 3pF

ꢀ On-Board Thermal Shutdown Circuitry

ꢀ SCSI Bus Hot Plug Compatible

R5P

R6P

DIFF_CAP

DIFFSENSE

MSTR/SLV

R5N

ISO

GND

ꢀ Fully Supports Actively Negated SE SCSI

TSSOP

Signals

ORDERING INFORMATION

VOLTAGE

PART

TEMP RANGE PIN-PACKAGE

TOP MARK*

(V)

DS2119ME

DS2119ME+

28 TSSOP (0.173")

DS2119M

0°C to +70°C

28 TSSOP (0.173")/Tape

and Reel

DS2119ME/T&R

DS2119M

0°C to +70°C

28 TSSOP (0.173")/Tape

and Reel

DS2119ME+T&R

DS2119M

0°C to +70°C

+ Denotes a lead-free/RoHS-compliant package.

* The top mark includes a "+" on lead-free packages.

DETAILED DESCRIPTION

The DS2119M Ultra3 LVD/SE SCSI terminator is both a low-voltage differential (LVD) and single-

ended (SE) terminator. The multimode operation enables the designer to implement LVD in current

products while allowing the end-user SE-backward compatibility with legacy devices. If the device is

connected in an LVD-only bus, the DS2119M will use LVD termination. If any SE devices are connected

to the bus, the DS2119M will use SE termination. This is accomplished automatically inside the part by

sensing the voltage on the SCSI bus DIFFSENS line.

For the LVD termination, the DS2119M integrates two current sources with nine precision resistor

strings. For the SE termination, one regulator and nine precision 110Ω resistors are used. Three

DS2119M terminators are needed for a wide SCSI bus.

1 of 9

REV: 010406

DS2119M

REFERENCE DOCUMENTS

Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface (SPI)

Project: 0855-M, 1995

Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface 2 (SPI-2) Project: 1142-M, 1998

Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface 3 (SPI-3) Project: 1302-D, 1999

Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface 4 (SPI-4) Project: 1365-D, 200x

Available From:

American National Standards Institute (ANSI) Phone: (212) 642-4900

Global Engineering Documents 15 Inverness Way East; Englewood, CO 80112 Phone: (800) 854-7179

FUNCTIONAL DESCRIPTION

The DS2119 combines LVD and SE termination with DIFFSENS sourcing and detection.

A bandgap reference is fed into two amplifiers, which creates a 1.25V reference voltage and a 2.85V

reference voltage. The control logic determines which of these references will be applied to the

termination resistors. If the SCSI bus is in LVD mode, then the 1.25V reference will be used. If the SCSI

bus is in SE mode, then the 2.85V reference will be used. That same control logic will switch in/out

parallel resistors to change the total termination resistance accordingly. Finally, in SE mode, the Rp pins

will be switched to ground.

The DIFFSENSE circuitry decodes trinary logic. There will be one of three voltages on the SCSI control

line called DIFFSENS. Two comparators and a NAND gate determine if the voltage is below 0.6V, above

2.15V, or in between. That indicates the mode of the bus to be SE, HVD, or LVD, respectively.

The DS2119M’s DIFF_CAP pin monitors the DIFFSENS line to determine the proper operating mode of

the device. The DIFFSENSE pin can also drive the SCSI DIFFSENS line (when MSTR/SLV = 1) to

determine the SCSI bus-operating mode. The DS2119M switches to the termination mode that is

appropriate for the bus based on the value of the DIFFSENS voltage. These modes are:

ꢀ LVD Mode: LVD termination is provided by a precision laser-trimmed resistor string with two

current sources. This configuration yields a 105Ω differential and 150Ω common-mode

impedance. A fail-safe bias of 112mV is maintained when no drivers are connected to the SCSI

bus.

ꢀ SE Mode: When the external driver for a given signal line turns off, the active terminator will pull

that signal line to 2.85V (quiescent state). When used with an active negation driver, the power

amp can sink 22mA per line and the reference voltage will move less than 100mV. The

terminating resistors maintain their 110Ω value.

ꢀ HVD Isolation Mode: The DS2119M identifies that there is an HVD (high-voltage differential)

device on the SCSI bus and isolates the termination pins from the bus.

When ISO = 1, the termination pins are isolated from the SCSI bus, V_REFremains active. During thermal

shutdown, the termination pins are isolated from the SCSI bus and V_REFbecomes high impedance. The

DIFFSENSE driver is shut down during either of these two events.

To ensure proper operation, the TPWR pin should be connected to the SCSI bus TERMPWR line. As

with all analog circuitry, the TERMPWR and V_DDlines should be bypassed locally. A 2.2µF capacitor

and a 0.01µF high-frequency capacitor are recommended between TPWR and ground and placed as close

2 of 9

DS2119M

as possible to the DS2119M. The DS2119M should be placed as close as possible to the SCSI connector

to minimize signal and power-trace length, thereby resulting in less input capacitance and reflections,

which can degrade the bus signals.

To maintain the specified regulation, a 4.7µF capacitor is required between the V_REFpin (VREF) and

ground of each DS2119M. A high frequency cap (0.1µF ceramic recommended) can also be placed on the

V_REFpin in applications that use fast rise/fall time drivers. A typical SCSI bus configuration is shown in

Figure 2.

ꢀ DIFFSENS Noise Filtering: The DS2119M incorporates a digital filter to remove high-frequency

transients on the DIFFSENS control line, thereby eliminating erroneous switching between

modes. This filter eliminates the need for the external capacitor and resistor, which heretofore

performed this function.

NOTES:

1) DIFFSENS. Refers to the SCSI bus signal.

2) DIFFSENSE. Refers to the Dallas Semiconductor pin name and internal circuitry relating the

DIFFSENS driver.

3 of 9

DS2119M

Figure 1. DS2119M Block Diagram

4 of 9

DS2119M

Figure 2. SCSI Bus Configuration

5 of 9

DS2119M

PIN DESCRIPTION

NAME

FUNCTION

Reference Voltage. 2.85V reference in SE mode and 1.25V reference in

VREF

LVD mode; must be decoupled with a 4.7µF cap.

2–5, 7–12,

RxP,

RxN

Signal Termination. Connect to SCSI bus signal lines.

18–21, 23–26

Heat Sink Ground. Internally connected to the mounting pad. Should

be grounded.

6, 22

HS GND

Isolation. When pulled high, the DS2119M isolates its bus pins (RxP,

RxN) from the SCSI bus.

ISO

GND

Ground. Signal ground; 0V.

Master/Slave. Mode-select for the noncontrolling terminator. When

pulled high, MSTR enables the DIFFSENSE driver.

MSTR/SLV

DIFFSENSE DIFFSENSE. Output to drive the SCSI bus DIFFSENS line.

DIFFSENSE Capacitor. Connect a 0.1µF capacitor for DIFFSENSE

DIFF_CAP filter. Input to detect the type of device (differential or single-ended) on

the SCSI bus.

Termination Power. Connect to the SCSI TERMPWR line and

27, 28

TPWR

decouple with a 2.2µF capacitor.

RECOMMENDED OPERATING CONDITIONS

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS NOTES

SE Mode

V_TPWR(SE)

4.0

5.5

Termpower

Voltage

Logic 0

Logic 1

LVD Mode

V_TPWR(LVD)

V_IL

2.7

-0.3

5.5

+0.8

V_TPWR

0.3

V_IH

2.0

Operating Temperature

V_AMB

°C

6 of 9

DS2119M

SINGLE-ENDED CHARACTERISTICS

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

NOTES

SE Termination

R_SE

104.5

110

115.5

Ω

Resistance

SE Voltage Reference

SE Output Current

Output Capacitance

V_REF

l_OSE

2.7

2.85

3.0

25.4

C_OUT

LOW-VOLTAGE DIFFERENTIAL CHARACTERISTICS

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

NOTES

Differential Mode

R_DM

100

110

Ω

Termination Resistance

Common Mode

R_CM

110

190

Ω

Termination Resistance

Differential Mode Bias

Common Mode Bias

V_DM

V_CM

100

1.125

125

1.375

DC CHARACTERISTICS

PARAMETER

SYMBOL

I_TPMR

MIN

TYP

MAX

UNITS

NOTES

Termpower Current

Input Leakage High

Input Leakage Low

Output Current High

Output Current Low

DIFFSENS SE

µA

I_IH

-1.0

I_IL

I_OH

I_OL

1.0

-1.0

4.0

5, 7

6, 7

V_SEOR

V_LVDOR

V_HVDOR

V_DSO

-0.3

0.7

2.4

1.2

0.5

1.9

Operating Range

DIFFSENS LVD

Operating Range

DIFFSENS HVD

Operating Range

DIFFSENSE Driver

Output Voltage

DIFFSENSE Driver

Source Current

DIFFSENSE Driver

Sink Current

V_TPWR

0.3

1.4

8, 9

I_DSH

8, 10, 12

I_DSL

200

µA

ºC

8, 11

Thermal Shutdown

150

7 of 9

DS2119M

REGULATOR CHARACTERISTICS

(T_A= 0°C to +70°C)

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

NOTES

Line Regulation

LI_REG

LO_REG

I_LIM

1.0

1.3

550

2.5

3.5

Load Regulation

Current Limit

Sink Current

I_SINK

200

NOTES:

1) V_LINE= 0V to 3V.

2) V_LINE= 0.2V.

3) Guaranteed by design.

4) All lines open.

5) V_OUT= 2.4V.

6) V_OUT= 0.4V.

7) SE/LVD/HVD pins only.

8) MSTR/SLV = 1.

9) I_DS= 0mA to 5mA.

10) V_DSO= 0V.

11) V_DSO= 2.75V.

12) TPWR = 5.5V.

8 of 9

DS2119M

PACKAGE INFORMATION

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package

outline information, go to www.maxim-ic.com/DallasPackInfo.)

9 of 9

Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.

No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.

DS2119ME+T&R [MAXIM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E