MAX1531ETJ/V+T [MAXIM]
Switching Controller, Current-mode, 575kHz Switching Freq-Max, BICMOS, TQFN-32;型号: | MAX1531ETJ/V+T |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Switching Controller, Current-mode, 575kHz Switching Freq-Max, BICMOS, TQFN-32 信息通信管理 开关 |
文件: | 总33页 (文件大小:1312K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EVALUATION KIT AVAILABLE
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
General Description
Features
● 4.5V to 28V Input Voltage Range
The MAX1530/MAX1531 multiple-output power-supply
controllers generate all the supply rails for thin-film tran
sistor (TFT) liquid-crystal display (LCD) monitors. Both
devices include a high-efficiency, fixed-frequency, step-
down regulator. The low-cost, all N-channel, synchronous
topology enables operation with efficiency as high as 93%.
High-frequency operation allows the use of small induc-
tors and capacitors, resulting in a compact solution. The
MAX1530 includes three linear regulator controllers and
the MAX1531 includes five linear regulator controllers for
supplying logic and LCD bias voltages. A programmable
startup sequence enables easy control of the regulators.
● 250kHz/500kHz Current-Mode Step-Down Converter
• Small Inductor/Capacitors
• No Sense Resistor
● Three Positive Linear Regulator Controllers
• One Positive and One Negative Additional
Controller (MAX1531)
• Small Input and Output Capacitors
● Timed Reset Output
● Uncommitted Overcurrent Protection (MAX1531)
● Soft-Start for All Regulators
The MAX1530/MAX1531 include soft-start functions to
limit inrush current during startup. An internal stepdown
converter current-limit function and a versatile overcurrent
shutdown protect the power supplies against fault condi-
tions. The MAX1530/MAX1531 use a currentmode control
architecture, providing fast load transient response and
easy compensation. An internal linear regulator provides
MOSFET gate drive and can be used to power small
external loads.
● Programmable Input Undervoltage Comparator
● Programmable Startup Sequencing
Minimal Operating Circuit
V
IN
V
IN
V
P
CSH
CSL
V
V
L
N
BST
IN
V
= 12V
IN
The MAX1530/MAX1531 can operate from inputs as
high as 28V and are well suited for LCD monitor and TV
applications running directly from AC/DC wall adapters.
Both devices are available in a small (5mm x 5mm), ultra-
thin (0.8mm), 32-pin QFN package and operate over the
-40°C to +85°C temperature range.
DRV4
FBL4
DH
LX
V
V
OUT
3.3V/1.5A
SOURCE
10V/500mA
MAX1530
DL
PGND
FB
EN
ILIM
FREQ
VL
Applications
V
L
COMP
● LCD Monitors and TVs
AGND
RESET
Ordering Information
RSTIN
V
V
IN
V
OUT
PART
TEMP RANGE
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
PIN-PACKAGE
32 TQFN-EP*
32 TQFN-EP*
32 TQFN-EP*
32 TQFN-EP*
DRV2
FBL2
MAX1530ETJ+
MAX1530ETJ+T
MAX1531ETJ+
MAX1531ETJ+T
DRV1
FBL1
GAMMA
-9.7V
V
LOGIC
25V/500mA
ONL2
ONL3
ONL4
ONL5
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
V
L
SEQ
V
P
V
V
IN
*EP = Exposed pad.
DRV3
FBL3
DRV5
FBL5
V
GON
25V
GOFF
Pin Configuration appears at end of data sheet.
-9V
19-2866; Rev 3; 3/14
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Absolute Maximum Ratings
IN, DRV1, DRV2, DRV3, DRV4, CSH,
SEQ, ONL2, ONL3, ONL4, ONL5, COMP,
CSL to AGND ....................................................-0.3V to +30V
DRV5 to VL .............................................................-28V to +0.3V
CSH to CSL ..............................................................-0.3V to +6V
VL to AGND..............................................................-0.3V to +6V
PGND to AGND...................................................................±0.3V
LX to BST..................................................................-6V to +0.3V
BST to AGND..........................................................-0.3V to +36V
DH to LX .....................................................-0.3V to (BST + 0.3V)
DL to PGND ..................................................-0.3V to (VL + 0.3V)
ILIM to AGND...........................................-0.3V to (VL + 0.3V)
RSTIN, RESET, EN, FB, FBL1, FBL2, FBL3, FBL4, FBL5,
FREQ to AGND....................................................-0.3V to +6V
VL Short Circuit to AGND ...........................................Momentary
Continuous Power Dissipation (T = +70°C)
A
32-Pin Thin QFN (derate 21.3mW/°C above +70°C) ...1702mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(Circuit of Figure 1, V = 12V, V
= V
= 5V, T = 0°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.)
IN
EN
SEQ
A
A
PARAMETER
GENERAL
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Input Voltage Range
(Note 1)
4.5
28.0
3.0
V
V
V
= V
= V
= V
= 0V
=
FB
FBL1
FBL2
FBL3
Quiescent Supply Current
1.7
mA
µA
= 1.5V, V
FBL4
FBL5
IC Disable Supply Current
VL REGULATOR
EN = AGND
200
400
VL Output Voltage
5.5V < V < 28V, 0 < I < 30mA
4.75
3.2
5
5.25
3.8
V
V
IN
VL
VL Undervoltage Lockout Threshold
CONTROL AND SEQUENCE
SEQ, FREQ Input Logic High Level
SEQ, FREQ Input Logic Low Level
SEQ, FREQ Input Leakage Current
ONL_ Input Threshold
VL rising, 3% hysteresis
3.5
2.0
V
V
0.6
+1
-1
µA
V
ONL_ rising, 25mV hysteresis
1.201
1.8
1.238
2.0
1.275
2.2
ONL_ Source Current
SEQ = EN = VL, V
= 0 to 1.24V
µA
nA
Ω
ONL _
ONL_ Input Leakage Current
SEQ = EN = VL, ONL_ = VL
= 0V
-500
800
+500
3000
1.275
+50
ONL_ Input Discharge Clamp Resistance
EN Input Threshold
V
1500
SEQ
EN rising, 5% hysteresis
1.201
-50
1.238
V
EN Input Leakage Current
FAULT DETECTION
nA
FB, FBL1, FBL2, FBL3, FBL4
Undervoltage Fault Trip Level
FB, FBL1, FBL2, FBL3, FBL4 falling,
25mV hysteresis
1.081
300
1.114
400
1.147
500
V
FBL5 Undervoltage Fault Trip Level
FBL5 rising, 25mV hysteresis
mV
Maxim Integrated
│ 2
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Electrical Characteristics (continued)
(Circuit of Figure 1, V = 12V, V
= V
= 5V, T = 0°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.)
IN
EN
SEQ
A
A
PARAMETER
Comparator Bandwidth
CONDITIONS
MIN
TYP
10
MAX
UNITS
kHz
ms
For EN, FB, FBL_
For FB, FBL_
Duration to Trigger Fault Latch
51
270
2.7
64
77
Overcurrent Protection Threshold
(V
- V
)
300
330
28.0
100
+50
mV
V
CSH
CSL
Overcurrent Sense Common-Mode Range
CSH Input Current
V
V
V
, V
CSH CSL
= 2.7V to 28V
µA
CSH
CSL
CSL Input Current
= V
= 12V
-50
nA
CSH
Overcurrent Sense Filter RC Time
Constant
50
µs
°C
THERMAL PROTECTION
Thermal Shutdown
Temperature rising, 15°C hysteresis
RSTIN falling, 25mV hysteresis
160
RESET FUNCTION
RSTIN Reset Trip Level
RSTIN Input Leakage Current
Comparator Bandwidth
1.081
-50
1.114
1.147
+50
V
nA
kHz
ms
V
V
= 1.5V
RSTIN
10
Reset Timeout Period
102
128
154
0.4
1
RESET Output Low Level
RESET Output High Leakage
STEP-DOWN CONTROLLER
ERROR AMPLIFIER
I
= -1mA
= 5V
RESET
V
µA
RESET
FB Regulation Voltage
1.223
70
1.238
100
200
15
1.253
140
V
µS
V/V
%
Transconductance
FB to COMP
FB to COMP
Voltage Gain
Minimum Duty Cycle
FB Input Leakage Current
FB Input Common-Mode Range
COMP Output Minimum Voltage
COMP Output Maximum Voltage
Current-Sense Amplifier Voltage Gain
Current-Limit Threshold (Default Mode)
V
= 1.5V
-50
+50
nA
V
FB
(Note 2)
-0.1
+1.5
V
V
V
= 1.5V
1
V
FB
FB
IN
= 1.175V
3
V
- V
2.75
190
190
3.0
3.5
250
250
3.5
4.0
310
310
4.00
V/V
mV
mV
V
LX
PGND - LX, ILIM = VL
Current-Limit Threshold (Adjustable Mode) PGND - LX, V
ILIM Input Dual Mode™ Threshold
OSCILLATOR
= 1.25V
ILIM
FREQ = AGND
FREQ = VL
200
425
75
250
500
80
300
575
88
Switching Frequency
Maximum Duty Cycle
kHz
%
FREQ = AGND
FREQ = VL
75
80
88
Maxim Integrated
│ 3
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Electrical Characteristics (continued)
(Circuit of Figure 1, V = 12V, V
= V
= 5V, T = 0°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.)
IN
EN
SEQ
A
A
PARAMETER
SOFT-START
CONDITIONS
MIN
TYP
MAX
UNITS
Step Size
Measured at FB
FREQ = GND
FREQ = VL
1.238/32
V
s
1024/f
2048/f
OSC
OSC
Period
FET DRIVERS
DH, DL On-Resistance
DH, DL Output Drive Current
LX, BST Leakage Current
3
10
20
Ω
A
Sourcing or sinking, V
or V = V / 2
0.5
DH
DL
VL
V
= V = V = 28V
µA
BST
LX
IN
LINEAR REGULATOR CONTROLLERS
POSITIVE LINEAR REGULATOR (LR1)
FBL1 Regulation Voltage
V
V
= 5V, I
= 1.5V
= 100µA
1.226
-50
1.245
-15
1.264
+50
V
DRV1
FBL1
DRV1
FBL1 Input Bias Current
nA
FBL1 Effective Load Regulation
Error (Transconductance)
V
= 5V, I
= 100µA to 2mA
-2
5
%
DRV1
DRV1
DRV1
FBL1 Line Regulation Error
DRV1 Sink Current
I
= 100µA, 5.5V < V < 28V
mV
mA
µA
V
IN
V
V
= 1.175V, V
= 5V
3
10
FBL1
DRV1
DRV1 Off-Leakage Current
FBL1 Input Common-Mode Range
Soft-Start Step Size
1 = 1.5V, V
= 28V
0.1
10
FBL
DRV1
(Note 2)
-0.1
+1.5
Measured at FBL1
FREQ = GND
FREQ = VL
1.238 / 32
V
1024/f
2048/f
OSC
OSC
Soft-Start Period
s
POSITIVE LINEAR REGULATORS (LR2 AND LR3)
FBL_ Regulation Voltage
FBL_ Input Bias Current
V
V
= 5V, I
= 1.5V
= 100µA
1.226
-50
1.245
-1.5
1.264
+50
V
DRV_
FBL _
DRV_
nA
FBL_ Effective Load Regulation
Error (Transconductance)
V
= 5V, I
= 50µA to 1mA
-2
5
%
DRV_
DRV_
FBL_ Line Regulation Error
DRV_ Sink Current
I
= 100µA, 5.5V < V < 28V
mV
mA
µA
V
DRV_
IN
V
V
= 1.175V, V
= 5V
2
4
FBL_
DRV_
DRV_ Off-Leakage Current
FBL_ Input Common-Mode Range
Soft-Start Step Size
= 1.5V, V
= 28V
0.1
10
FBL _
DRV_
(Note 2)
Measured at FBL_
-0.1
+1.5
1.238 / 32
V
Maxim Integrated
│ 4
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Electrical Characteristics (continued)
(Circuit of Figure 1, V = 12V, V
= V
= 5V, T = 0°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.)
IN
EN
SEQ
A
A
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Soft-Start Period
FREQ = GND
FREQ = VL
1024 / f
2048 / f
s
OSC
OSC
POSITIVE LINEAR REGULATOR (LR4)
FBL4 Regulation Voltage
V
V
= 5V, I
= 1.5V
= 500µA
1.226
-50
1.245
-1.5
1.264
+50
V
DRV4
FBL4
DRV4
FBL4 Input Bias Current
nA
FBL4 Effective Load Regulation
Error (Transconductance)
V
= 5V, I
= 500µA to 10mA
-2
5
DRV4
DRV4
DRV4
%
mV
mA
µA
V
FBL4 Line Regulation Error
DRV4 Sink Current
I
= 500µA, 5.5V < V < 28V
IN
V
V
= 1.175V, V
= 5V
10
28
FBL4
FBL4
DRV4
DRV4_Off-Leakage Current
FBL4 Input Common-Mode Range
Soft-Start Step Size
= 1.5V, V
= 28V
0.1
10
DRV4
(Note 2)
-0.1
+1.5
Measured at FBL4
FREQ = GND
FREQ = VL
1.238 / 32
V
1024 / f
2048 / f
OSC
OSC
Soft-Start Period
s
NEGATIVE LINEAR REGULATOR (LR5)
FBL5 Regulation Voltage
V
V
= -10V, I
= 0V
= 100µA
100
-50
125
-1.5
150
+50
mV
nA
DRV5
FBL5
DRV5
FBL5 Input Bias Current
FBL5 Effective Load Regulation
Error (Transconductance)
V
= -10V, I
= 50µA to 1mA
-2
5
%
DRV5
DRV5
DRV5
FBL5 Line Regulation Error
DRV5 Source Current
I
= 100µA, 5.5V < V < 28V
mV
mA
µA
V
IN
V
V
= 200mV, V
= -10V
2
9
FBL5
FBL5
DRV5
DRV5 Off-Leakage Current
FBL5 Input Common-Mode Range
Soft-Start Step Size
= 0V, V
= -20V
0.1
10
DRV5
(Note 2)
-0.1
+15
Measured at FBL5
FREQ = AGND
FREQ = VL
1.238 / 32
V
1024 / f
2048 / f
OSC
OSC
Soft-Start Period
s
Electrical Characteristics
(Circuit of Figure 1, V = 12V, V
= V
= 5V, T = -40°C to +85°C, unless otherwise noted.) (Note 3)
IN
EN
SEQ A
PARAMETER
GENERAL
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Input Voltage Range
VL REGULATOR
(Note 1)
4.5
28.0
V
VL Output Voltage
5.5V < V < 28V, 0 < I < 30mA
4.75
3.2
5.25
3.8
V
V
IN
VL
VL Undervoltage Lockout
Threshold
VL rising, 3% hysteresis
Maxim Integrated
│ 5
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Electrical Characteristics (continued)
(Circuit of Figure 1, V = 12V, V
= V
= 5V, T = -40°C to +85°C, unless otherwise noted.) (Note 3)
IN
EN
SEQ A
PARAMETER
CONTROL AND SEQUENCE
ONL_ Input Threshold
EN Input Threshold
CONDITIONS
MIN
TYP
MAX
UNITS
ONL_ rising, 25mV hysteresis
EN rising, 5% hysteresis
1.201
1.201
1.275
1.275
V
V
FAULT DETECTION
FB, FBL1, FBL2, FBL3, FBL4
Fault Trip Level
FB, FBL1, FBL2, FBL3, FBL4 falling,
25mV hysteresis
1.081
1.147
V
FBL5 Fault Trip Level
FBL5 rising, 25mV hysteresis
300
270
500
330
mV
mV
Overcurrent Protection Threshold
RESET FUNCTION
(V
- V
)
CSH
CSL
RSTIN Reset Trip Level
STEP-DOWN CONTROLLER
ERROR AMPLIFIER
RSTIN falling, 25mV hysteresis
1.081
1.147
V
FB Regulation Voltage
1.215
170
1.260
330
V
Current-Limit Threshold
(Default Mode)
PGND - LX, ILIM = VL
mV
Current-Limit Threshold
(Adjustable Mode)
PGND - LX, V
= 1.25V
170
330
mV
ILIM
LINEAR REGULATOR CONTROLLERS
POSITIVE LINEAR REGULATOR (LR1)
FBL1 Regulation Voltage
FBL1 Input Bias Current
V
V
= 5V, I
= 1.5V
= 100µA
= 100µA
= 500µA
1.220
-50
1.270
+50
V
DRV1
DRV1
nA
FBL1
POSITIVE LINEAR REGULATORS (LR2 AND LR3)
FBL_ Regulation Voltage
FBL_ Input Bias Current
V
V
= 5V, I
= 1.5V
1.220
-50
1.270
+50
V
DRV_
DRV_
nA
FBL_
POSITIVE LINEAR REGULATOR (LR4)
FBL4 Regulation Voltage
FBL4 Input Bias Current
V
V
= 5V, I
= 1.5V
1.220
-50
1.270
+50
V
DRV4
DRV4
nA
FBL4
NEGATIVE LINEAR REGULATOR (LR5)
FBL5 Regulation Voltage
FBL5 Input Bias Current
DRV5 Source Current
V
V
V
= -10V, I
= 100µA
DRV5
100
-50
2
150
+50
mV
nA
DRV5
FBL5
FBL5
= 0V
= 200mV, V
= -10V
mA
DRV5
Note 1: Operating supply range is guaranteed by VL line regulation test for the range of 5.5V to 28V. Between 4.5V and 5.5V, theV
regulator might be in dropout; however, the part continues to operate properly.
L
Note 2: Guaranteed by design and not production tested.
Note 3: Specifications to -40°C are guaranteed by design and not production tested.
Maxim Integrated
│ 6
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Typical Operating Characteristics
(Circuit of Figure 1; including R5, R6, and D2; T = +25°C, unless otherwise noted.)
A
STEP-DOWN EFFICIENCY
vs. LOAD CURRENT
STEP-DOWN LOAD
REGULATION
SWITCHING FREQUENCY
vs. LOAD CURRENT
100
90
80
70
60
50
0
-0.04
-0.08
-0.12
-0.16
520
f
= 500kHz
SW
515
510
505
500
495
490
485
480
V
IN
= 12V
V
IN
= 20V
0
300
600
900
1200
1500
0
300
600
900
1200
1500
0
300
600
900
1200
1500
LOAD CURRENT (mA)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
STEP-DOWN REGULATOR
LOAD TRANSIENT
STEP-DOWN REGULATOR
SOFT-START
STEP-DOWN REGULATOR
SWITCHING WAVEFORM
MAX1530 toc04
MAX1530 toc06
MAX1530 toc05
A
A
B
C
A
B
0V
0V
0A
B
3.3V
3.3V
0V
0A
C
C
0A
0A
40µs/div
1µs/div
2µs/div
A: EN, 2V/div
A: LX, 10V/div
A: LOAD CURRENT, 1A/div
B: OUTPUT VOLTAGE, 2V/div
C: INDUCTOR CURRENT, 1A/div
B: OUTPUT VOLTAGE, 20 mV/div, AC-COUPLED
C: INDUCTOR CURRENT, 1A/div
B: OUTPUT VOLTAGE, 200mV/div, AC-COUPLED
C: INDUCTOR CURRENT, 1A/div
LR1 BASE CURRENT
vs. DRV1 VOLTAGE
VL LOAD REGULATION
STARTUP SEQUENCE
MAX1530 toc08
0
-0.1
-0.2
-0.3
-0.4
-0.5
15
12
9
A
B
V
FBL1
= 1.175V
C
D
E
6
F
3
G
0
0
5
10
15
20
25
30
4ms/div
0
2
4
6
8
10
A: V , 10V/div
E: V
, 20V/div
GAMMA
LOAD CURRENT (mA)
L
DRV1 VOLTAGE (V)
B: V , 5V/div
F: V
, 20V/div
, 40V/div
OUT
GOFF
C: V
D: V
, 5V/div
G: V
GON
LOGIC
, 20V/div
SOURCE
Maxim Integrated
│ 7
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Typical Operating Characteristics (continued)
(Circuit of Figure 1; including R5, R6, and D2; T = +25°C, unless otherwise noted.)
A
LR1 NORMALIZED LOAD REGULATION
LR1 NORMALIZED LINE REGULATION
LR1 LOAD TRANSIENT
MAX1530 toc12
0
-0.5
-1.0
-1.5
-2.0
0.2
0
A
2.5V
-0.2
-0.4
-0.6
-0.8
-1.0
B
0mA
200mA LOAD CURRENT
0
100
200
300
400
500
2
3
4
5
6
40µs/div
A: LR1 OUTPUT VOLTAGE, 100mV/div, AC-COUPLED
B: LR1 LOAD CURRENT, 500mA/div
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
LR2/LR3 BASE CURRENT
vs. DRV2/DRV3 VOLTAGE
LR2 NORMALIZED LOAD REGULATION
LR2 NORMALIZED LINE REGULATION
5
0
-0.3
-0.6
-0.9
-1.2
-1.5
0.2
0
V
FBL2
= V
= 1.175V
FBL3
4
3
2
1
0
-0.2
-0.4
-0.6
-0.8
-1.0
20mA LOAD CURRENT
0
1
2
3
4
5
0
10
20
30
40
50
9
13
17
21
25
DRV2/DRV3 VOLTAGE (V)
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
LR3 NORMALIZED LOAD REGULATION
LR3 NORMALIZED LINE REGULATION
LR4 BASE CURRENT vs. DRV VOLTAGE
0
-0.5
-1.0
-1.5
-2.0
0.2
0
30
25
20
15
10
5
V
FBL4
= 1.175V
-0.2
-0.4
-0.6
-0.8
-1.0
20mA LOAD CURRENT
0
0
4
8
12
16
20
24
28
32
36
40
0
2
4
6
8
10
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
DRV4 VOLTAGE (V)
Maxim Integrated
│ 8
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Typical Operating Characteristics (continued)
(Circuit of Figure 1; including R5, R6, and D2; T = +25°C, unless otherwise noted.)
A
LR4 NORMALIZED LOAD REGULATION
LR4 NORMALIZED LINE REGULATION
0
0.2
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
0
-0.2
-0.4
-0.6
-0.8
200mA LOAD CURRENT
-1.0
0
100
200
300
400
500
9
13
17
21
25
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
LR4 LOAD TRANSIENT
LR4 PULSED LOAD TRANSIENT
MAX1530 toc22
MAX1530 toc21
A
B
A
B
10V
10V
0mA
0A
40µs/div
10µs/div
A: LR4 OUTPUT VOLTAGE, 100mV/div, AC-COUPLED
A: LR4 OUTPUT VOLTAGE, 100mV/div, AC-COUPLED
B: LR4 LOAD CURRENT, 500mA/div
B: LR4 LOAD CURRENT, 1A/div
MAX1531
LR5 BASE CURRENT
vs. DRV5 VOLTAGE
OVERCURRENT PROTECTION (CSH, CSL)
MAX1530 toc23
10
8
V
FBL5
= 0V
A
B
6
4
C
2
D
0
20µs/div
0
1
2
3
4
5
A: V , 10V/div
LX
C: V
D: V
, 5V/div
- V , 500mV/div
CSL
RESET
DRV5 VOLTAGE (V)
B: V , 5V/div
OUT
CSH
Maxim Integrated
│ 9
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Typical Operating Characteristics (continued)
(Circuit of Figure 1; including R5, R6, and D2; T = +25°C, unless otherwise noted.)
A
LR5 NORMALIZED LOAD REGULATION
LR5 NORMALIZED LINE REGULATION
0
1.0
20mA LOAD CURRENT
0.8
-0.2
-0.4
-0.6
-0.8
-1.0
0.6
0.4
0.2
0
-0.2
0
10
20
30
40
50
-25
-21
-17
-13
-9
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
Pin Description
PIN
NAME
FUNCTION
MAX1530
MAX1531
Gamma Linear Regulator (LR2) Base Drive. Open drain of an internal N-channel
MOSFET. Connect DRV2 to the base of an external PNP pass transistor to form a
positive linear regulator. (See the Pass Transistor Selection section.)
1
1
2
3
DRV2
Gamma Linear Regulator (LR2) Feedback Input. FBL2 regulates at 1.245V nominal.
Connect FBL2 to the center tap of a resistive voltage-divider between the LR2 output
and AGND to set the output voltage. Place the divider close to the FBL2 pin.
2
3
4
FBL2
FBL3
Gate-On Linear Regulator (LR3) Feedback Input. FBL3 regulates at 1.245V nominal.
Connect FBL3 to the center tap of a resistive voltage-divider between the LR3 output
and AGND to set the output voltage. Place the divider close to the FBL3 pin.
Gate-On Linear Regulator (LR3) Base Drive. Open drain of an internal N-channel
MOSFET. Connect DRV3 to the base of an external PNP pass transistor to form a
positive linear regulator. (See the Pass Transistor Selection section.)
4
DRV3
N. C.
5–10,
18, 19
—
No Connection. Not internally connected.
Adjustable Reset Input. RESET asserts low when the monitored voltage is less
than the reset trip threshold. RESET goes to a high-impedance state only after the
monitored voltage remains above the reset trip threshold for the duration of the reset
timeout period. Connect RSTIN to the center tap of a resistive voltage-divider between
the monitored output voltage and AGND to set the reset trip threshold. The internal
RSTIN threshold of 90% of 1.238V allows direct connection of RSTIN to any of the
device’s positive feedback pins.
11
11
RSTIN
Maxim Integrated
│ 10
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Pin Description (continued)
PIN
NAME
FUNCTION
MAX1530
MAX1531
Open-Drain Reset Output. RESET asserts low when the monitored voltage is less
than the reset trip threshold. RESET goes to a high-impedance state only after the
monitored voltage remains above the reset trip threshold for the duration of the reset
timeout period. RESET also asserts low when VL is less than the VL undervoltage
lockout threshold, EN is low, or the thermal, overcurrent or undervoltage fault latches
are set.
12
12
RESET
Step-Down Regulator Compensation Input. A pole-zero pair must be added to
compensate the control loop by connecting a series resistor and capacitor from COMP
to AGND. (See the Compensation Design section.)
13
14
13
14
COMP
FB
Step-Down Regulator Feedback Input. FB regulates at 1.238V nominal. Connect FB
to the center tap of a resistive voltage-divider between the step-down regulator output
and AGND to set the output voltage. Place the divider close to the FB pin.
Step-Down Regulator Current-Limit Control Input. Connect this dual-mode input to VL
to set the current-limit threshold to its default value of 250mV. The overcurrent
comparator compares the voltage across the low-side N-channel MOSFET with
the current-limit threshold. Connect ILIM to the center tap of a resistive voltage-
divider between VL and AGND to adjust the current-limit threshold to other values. In
adjustable mode, the actual current-limit threshold is 1/5th of the voltage at ILIM over
a 0.25V to 3.0V range. The dual- mode threshold for switchover to the 250mV default
value is approximately 3.5V.
15
15
ILIM
Gamma Linear Regulator (LR2) Enable Input. When EN is above its enable threshold,
VL is above its UVLO threshold, and ONL2 is greater than the internal reference, LR2
is enabled. Drive ONL2 with a logic signal or, for automatic sequencing, connect a
capacitor from ONL2 to AGND. If SEQ is high, EN is above its threshold, and VL is
above its UVLO threshold, an internal 2µA (typ) current source charges the capacitor.
Otherwise, an internal switch discharges the capacitor. Connecting various capacitors
to each ONL_ pin allows the programming of the startup sequence.
16
17
16
17
ONL2
ONL3
Gate-On Linear Regulator (LR3) Enable Input. When EN is above its enable threshold,
VL is above its UVLO threshold, and ONL3 is greater than the internal reference, LR3
is enabled. Drive ONL3 with a logic signal or, for automatic sequencing, connect a
capacitor from ONL3 to AGND. If SEQ is high, EN is above its threshold, and VL is
above its UVLO threshold, an internal 2µA (typ) current source charges the capacitor.
Otherwise, an internal switch discharges the capacitor. Connecting various capacitors
to each ONL_ pin allows the programming of the startup sequence.
20
21
20
21
PGND
DL
Power Ground
Low-Side Gate Driver Output. DL drives the synchronous rectifier of the step-down
regulator. DL swings from PGND to VL. DL remains low until VL rises above the UVLO
threshold.
Step-Down Regulator Current-Sense Input. The IC’s current-sense amplifier inputs
for current-mode control connect to IN and LX. Connect IN and LX directly to the
high-side N- channel MOSFET drain and source, respectively. The low-side current-
limit comparator inputs connect to LX and PGND to sense voltage across a low-side
N-channel MOSFET.
22
22
LX
Maxim Integrated
│ 11
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Pin Description (continued)
PIN
NAME
FUNCTION
MAX1530
MAX1531
High-Side Gate Driver Output. DH drives the main switch of the step-down regulator.
DH swings from LX to BST.
23
23
DH
BST
Step-Down Regulator Boostrap Capacitor Connection for High-Side Gate Driver.
Connect a 0.1µF ceramic capacitor from BST to LX.
24
25
26
24
25
26
Sequence Control Input for LR2, LR3, LR4, and LR5. Controls the current sources and
switches that charge and discharge the capacitors connected to the ONL_ pins.
SEQ
FREQ
Oscillator Frequency Select Input. Connect FREQ to VL for 500kHz operation. Connect
FREQ to AGND for 250kHz operation.
Main Input Voltage (+4.5V to 28V). Bypass IN to AGND with a 1µF ceramic capacitor
close to the pins. IN powers the VL linear regulator. Connect IN to the drain of the high-
side MOSFET (for current sense) through a 1Ω resistor.
27
27
IN
Internal 5V Linear Regulator Output. Connect a minimum 1µF ceramic capacitor from
VL to AGND. Place the capacitor close to the pins. VL can supply up to 30mA for gate
drive and external loads. VL remains active when EN is low.
28
29
28
29
VL
AGND
Analog Ground
Enable Input. This general-purpose on/off control input has an accurate 1.238V (typ)
rising threshold with 5% hysteresis. This allows EN to monitor an input voltage level or
other analog parameter. If EN is less than its threshold, then the main step-down and
all linear regulators are turned off. VL and the internal reference remain active when EN
is low. The rising edge of EN clears any latched faults except for a thermal fault, which
is cleared only by cycling the input power. An internal filter with a 10µs time constant
prevents short glitches from accidentally clearing the fault latch.
30
30
EN
Low-Voltage Logic Linear Regulator (LR1) Feedback Input. FBL1 regulates at 1.245V
nominal. Connect FBL1 to the center tap of a resistive voltage-divider between LR1
output AGND to set the output voltage. Place the divider close to the FBL1 pin. LR1
starts automatically after the step-down converter soft-start ends.
31
32
31
32
FBL1
Low-Voltage Logic Linear Regulator (LR1) Base Drive. Open drain of an internal
N-channel MOSFET. Connect DRV1 to the base of an external PNP pass transistor.
(See the Pass Transistor Selection section.)
DRV1
Overcurrent Protection Positive Input. CSH is also the supply input for the overcurrent
sense block. CSH and CSL can be used to sense any current in the application circuit
and to shut the device down in an overcurrent condition. This feature is typically used
to protect the main input or the input to one of the linear regulators since they do not
have their own current limits. Insert an appropriate sense resistor in series with the
protected input and connect CSH and CSL to its positive and negative terminals. The
—
—
5
6
CSH
CSL
controller sets the fault latch when V
- V
exceeds the 300mV (typ) overcurrent
CSH
CSL
threshold. An internal lowpass filter prevents large currents of short duration (less than
50µs) or noise glitches from setting the latch. If the overcurrent protection is not used,
connect CSH and CSL to VL.
Overcurrent Protection Negative Input. See CSH above.
Maxim Integrated
│ 12
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Pin Description (continued)
PIN
NAME
FUNCTION
MAX1530
MAX1531
Source Drive Linear Regulator (LR4) Feedback Input. FBL4 regulates at 1.245V
nominal. Connect FBL4 to the center tap of a resistive voltage-divider between the LR4
output and AGND to set the output voltage. Place the divider close to the FBL4 pin.
—
7
FBL4
Source Drive Linear Regulator (LR4) Base Drive. Open drain of an internal N-channel
MOSFET. Connect DRV4 to the base of an external PNP pass transistor to form a
positive linear regulator. (See the Pass Transistor Selection section.)
—
—
—
8
9
DRV4
Gate-Off Linear Regulator (LR5) Feedback Input. FBL5 regulates at 125mV nominal.
Connect FBL5 to the center tap of a resistive voltage-divider between the LR5 output
and the internal 5V linear regulator output (VL) to set the output voltage. Place the
divider close to the FBL5 pin.
FBL5
Gate-Off Linear Regulator (LR5) Base Drive. Open drain of an internal P-channel
MOSFET. Connect DRV5 to the base of an external NPN pass transistor to form a
negative linear voltage regulator. (See the Pass Transistor Selection section.)
10
DRV5
Source Drive Linear Regulator (LR4) Enable Input. When EN is above its enable
threshold, VL is above its UVLO threshold, and ONL4 is greater than the internal
reference, LR4 is enabled. Drive ONL4 with a logic signal or, for automatic sequencing,
connect a capacitor from ONL4 to AGND. If SEQ is high, EN is above its threshold,
and VL is above its UVLO threshold, an internal 2µA (typ) current source charges the
capacitor. Otherwise, an internal switch discharges the capacitor. Connecting various
capacitors to each ONL_ pin allows the programming of the startup sequence.
—
18
ONL4
Gate-Off Linear Regulator (LR5) Enable Input. When EN is above its enable threshold,
VL is above its UVLO threshold, and ONL5 is greater than the internal reference, LR5
is enabled. Drive ONL5 with a logic signal or, for automatic sequencing, connect a
capacitor from ONL5 to AGND. If SEQ is high, EN is above its threshold, and VL is
above its UVLO threshold, an internal 2µA (typ) current source charges the capacitor.
Otherwise, an internal switch discharges the capacitor. Connecting various capacitors
to each ONL_ pin allows the programming of the startup sequence.
—
—
19
—
ONL5
EP
Exposed Paddle. Internally connected to GND. Connect EP to a large ground plane to
improve thermal dissipation. Do not use as the main ground connection of the IC.
Maxim Integrated
│ 13
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
V
= 12V
IN
C3
4.7µF
25V
C5
0.1µF
D1
R3
124kΩ
1%
R5*
10Ω
R4
20.0kΩ
1%
IN
24
BST
R12
1Ω
30
27
EN
IN
C1
1µF
V
L
5V/30mA
28
26
25
12
16
23
VL
DH
N1-A
C4
1µF
V
OUT
3.3V/1.5A
L1
10µH
FREQ
SEQ
22
21
LX
DL
C7
22µF
6.3V
R1
17.8kΩ
1%
R6*
10Ω
C23
150pF
R7
100kΩ
N1-B
RESET
ONL2
D2*
R2
10.7kΩ
1%
20
29
R8
6.8kΩ
C22
2.2µF
PGND
AGND
R14
121kΩ
1%
32
17
18
19
MAX1531
DRV1
FBL1
Q1
ONL3
ONL4
ONL5
R9
10kΩ
1%
R15
68.1kΩ
1%
V
LOGIC
2.5V/500mA
31
C9
10µF
6.3V
R10
10kΩ
1%
R16
43.2kΩ
1%
11
14
RSTIN
FB
C11
0.1µF
C10
470pF
R11
100kΩ
VL
R17
6.8kΩ
13
15
V
IN
COMP
ILIM
R12
C2, OPEN
D4
300kΩ
C20
0.1µF
1
2
Q2
DRV2
FBL2
R18
68.1kΩ
1%
D3
R13
150kΩ
V
GAMMA
V
IN
9.7V/50mA
C15
0.1µF
C8
C14
0.1µF
C6
0.1µF
R24
6.8kΩ
0.1µF
C12
0.47µF
R19
10kΩ
1%
LX
4
3
DRV3
FBL3
Q3
Q6
R25
200kΩ
1%
6
5
CSL
CSH
V
GON
25V/20mA
IN
R20
0.5Ω
1%
V
IN
C16
0.47µF
R26
10.5kΩ
C21
2.2µF
1%
R21
1.5kΩ
D5
8
7
DRV4
FBL4
Q4
C18
0.1µF
C17
0.1µF
R27
6.8kΩ
R22
75kΩ
1%
V
SOURCE
10V/500mA
LX
10
9
Q5
DRV5
FBL5
R28
C13
4.7µF
16V
R23
10.7kΩ
1%
V
90.9kΩ
GOFF
-9V/50mA
1%
C19
0.47µF
D6
R29
48.7kΩ
1%
*OPTIONAL
VL
Figure 1. MAX1531 Standard Application Circuit
Maxim Integrated
│ 14
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
V
= 12V
IN
C3
4.7µF
25V
C5
0.1mF
D1
R3
124kΩ
1%
R5*
10Ω
R4
IN
24
BST
20.0kΩ
1%
R12
1Ω
30
27
EN
IN
C1
1µF
V
L
5V/30mA
28
26
25
VL
23
22
21
DH
LX
DL
N1-A
C4
1µF
V
OUT
3.3V/1.5A
L1
10µH
FREQ
SEQ
C7
22µF
6.3V
R6*
10Ω
R1
C23
150pF
17.8kΩ
R7
100kΩ
1%
N1-B
12
16
D2*
RESET
ONL2
R2
C22
2.2µF
10.7kΩ
1%
20
29
R8
6.8kΩ
PGND
AGND
MAX1530
R14
121kΩ
1%
17
32
31
ONL3
DRV1
FBL1
Q1
C11
R9
10kΩ
1%
0.1µF
V
LOGIC
2.5V/500mA
5
6
7
8
N.C.
N.C.
N.C.
N.C.
C9
10µF
6.3V
R10
10kΩ
1%
11
14
RSTIN
FB
R17
6.8kΩ
V
IN
C10
470pF
R11
100kΩ
C20
0.1µF
VL
13
15
COMP
ILIM
1
2
Q2
DRV2
FBL2
R18
68.1kΩ
1%
C2, OPEN
R12
300kΩ
V
GAMMA
9.7V/50mA
R19
10kΩ
1%
C12
0.47µF
V
IN
C21
2.2µF
R13
150kΩ
R24
6.8kΩ
4
3
DRV3
FBL3
Q4
9
N.C.
N.C.
R22
75kΩ
1%
10
V
SOURCE
10V/500mA
C13
4.7µF
R23
10.7kΩ
1%
19
18
N.C.
N.C.
*OPTIONAL
Figure 2. MAX1530 Standard Application Circuit
Maxim Integrated
│ 15
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Table 1. Selected Component List
DESIGNATION
DESCRIPTION
DESIGNATION
DESCRIPTION
4.7µF, 25V X7R ceramic capacitor
(1210) TDK C3225X7R1E475K
200mA, 25V dual Schottky diodes
(SOT23) Fairchild BAT54S
C3
D3*, D4*, D5*
L1
22µF, 6.3V X7R ceramic capacitor
TDK C3216X7R0J226M
10µH, 2.3A (DC) inductor
Sumida CDR7D28MN-100
C7
C9
10µF, 6.3V X5R ceramic capacitor
TDK C2012X5R0J106M
2.5A, 30V dual N-channel MOSFET
(6-pin Super SOT)
N1
Fairchild FDC6561AN
0.47µF, 16V X7R ceramic capacitors
(0805) TDK C2012X7R1C474K
C12, C19*
C13
3A, 60V low-saturation PNP bipolar
transistors
(SOT-223) Fairchild NZT660A
Q1, Q4
4.7µF, 16V X7R ceramic capacitor
TDK C3216X7R1C475K
2.2µF, 25V X7R ceramic capacitors
(1206) TDK C3216X7R1C475M
200mA, 40V PNP bipolar transistors
(SOT23) Fairchild MMBT3906
C21, C22
D1, D6*
Q2, Q3*
100mA, 30V Schottky diodes (SOD523)
Central Semiconductor CMOSH-3
200mA, 40V NPN bipolar transistors
(SOT23) Fairchild MMBT3904
Q5*, Q6*
*For MAX1531 only.
100mA, 75V, small-signal switching
diode, SOT23 Fairchild Semiconductor
MMBD4148
D2
Table 2. Component Suppliers
SUPPLIER
Central Semi
PHONE
FAX
WEBSITE
www.centralsemi.com
www.fairchildsemi.com
www.sumida.com
516-435-1110
888-522-5372
847-956-0666
847-803-6100
516-435-1824
972-910-8036
847-956-0702
847-390-4405
Fairchild
Sumida
TDK
www.components.tdk.com
Standard Application Circuit
Detailed Description
The standard application circuit (Figure 1) of the MAX1531
is a complete power-supply system for TFT LCD moni-
tors. The circuit generates a 3.3V/1.5A main output, a
2.5V/500mA output for the timing controller and digital
sections of source/gate drive ICs, a 10V/500mA source
drive supply voltage, a 9.7V/50mA gamma reference, a
25V/20mA gate-on voltage, and a -10V/50mA gate-off
voltage. The input voltage is 12V ±10%. Table 1 lists the
selected components and Table 2 lists the component
suppliers. The standard application circuit (Figure 2) of
the MAX1530 is similar to the MAX1531 application circuit
except that gate-on and gate-off voltages are eliminated.
The MAX1530/MAX1531 power-supply controllers provide
logic and bias power for LCD monitors. Figure 3 shows
the IC functional diagram. The main step-down controller
employs a current-mode PWM control method to ease
compensation requirements and provide excellent load-
and line-transient response. The use of synchronous rec-
tification yields excellent efficiency.
The MAX1530 includes three analog gain blocks to control
three auxiliary positive linear regulators, and the MAX1531
includes five analog gain blocks to control four positive and
one negative linear regulators. Use the positive gain blocks
to generate low-voltage rails directly from the input voltage
or the main step-down converter output, or higher voltages
using charge pumps attached to the switching node or
Maxim Integrated
│ 16
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
MAX1531
THERMAL
FREQ
EN
RSTIN
RESET
V
REF
OSC
REF
IN
VLOK
VL
VL
TIMER
GND
HIGH-SIDE
DRIVER
BST
CLOCKSLOPE
IN
COMP
FB
COMP
FB
DH
DH
STEP-DOWN
CONTROLLER
LX
LX
DL
VL
ILIM
ILIM
DL
PGND
SS DONE DC-DC EN FLTM
LOW-SIDE
DRIVER
PGND
DRV3
ON2
ON3
ON4
ONL2
ONL3
ONL4
ONL5
SEQ
SOFT-
START
V
REF
SEQUENCE
ON5
FBL3
FLTM
SEQ
LR3
FLT3
DRV1
0.9VREF
LDO3EN
SOFT-
START
V
REF
DRV4
EN
V
FBL1
CSH
FAULT
LOGIC
REF
SOFT-
START
LR1
FLT1
0.9VREF
LDO4EN
FBL4
LR4
FLT4
0.9VREF
FLTCS
300mV
CSL
DRV5
DRV2
V
SOFT-
START
SOFT-
START
REF
V
REF
LDO2EN
FLT2
LDO5EN
FLT5
FBL5
FBL2
LR5
LR2
0.9VREF
400mV
EN
VLOK
Figure 3. IC Functional Diagram
Maxim Integrated
│ 17
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
During the second half of the cycle, the high-side
MOSFET turns off and the low-side N-channel MOSFET
turns on. Now the inductor releases the stored energy as
its current ramps down, providing current to the output.
The output capacitor stores charge when the inductor cur-
rent exceeds the load current and discharges when the
inductor current is lower, smoothing the voltage across
the load. Under overload conditions, when the inductor
current exceeds the selected current limit (see Current
Limit Circuit), the high-side MOSFET is not turned on at
the rising edge of the clock and the lowside MOSFET
remains on to let the inductor current ramp down.
CURRENT
SENSE
AND
CURRENT
LIMIT
IN
SLOPE
SS DONE
DC-DC EN
SOFT-
START
V
R
Q
Q
DH
DL
REF
GM
FB
PWM COMP
COMP
CLOCK
S
Under light-load conditions, the MAX1530/MAX1531
maintain a constant switching frequency to minimize
cross-regulation errors in applications that use a trans-
former. The low-side gate-drive waveform is the comple-
ment of the high-side gate-drive waveform, which causes
the inductor current to reverse under light loads.
CURRENT
LIMIT
LX
ILIM
PGND
FAULT COMPARATOR
FLTM
0.9VREF
Figure 4. Step-Down Controller Block Diagram
Current-Sense Amplifier
The MAX1530/MAX1531s’ current-sense circuit ampli-
fies the current-sense voltage generated by the highside
MOSFET’s on-resistance. This amplified current-sense
signal and the internal slope compensation signal are
summed together and fed into the PWM comparator’s
inverting input. Place the high-side MOSFET near the
controller, and connect IN and LX to the MOSFET using
Kelvin-sense connections to guarantee current-sense
accuracy and improve stability.
extra windings coupled to the step-down converter induc-
tor. The negative gain block (MAX1531) can be used in
conjunction with a charge pump or coupled winding to gen-
erate the LCD gate-off voltage or other negative supplies.
Step-Down Controller
The MAX1530/MAX1531 include step-down controllers
that use a fixed-frequency current-mode PWM control
scheme (Figure 4). An internal transconductance ampli-
fier establishes an integrated error voltage at the COMP
pin. The heart of the current-mode PWM controller is
an open-loop comparator that compares an integrated
voltage-feedback signal with an amplified current-sense
signal plus a slope-compensation ramp. At each rising
edge of the internal clock, the high-side MOSFET turns
on until the PWM comparator trips or the maximum duty
cycle is reached. During this on-time, current ramps up
through the inductor, sourcing current to the output and
storing energy in a magnetic field. The current-mode
feedback system regulates the peak inductor current as
a function of the output voltage error signal. Since the
average inductor current is nearly the same as the peak
inductor current (assuming that the inductor value is rela-
tively high to minimize ripple current), the circuit acts as
a switch-mode transconductance amplifier. That pushes
the output LC filter pole, normally found in a voltage-mode
PWM, to a higher frequency. To preserve loop stability, the
slopecompensation ramp is summed into the main PWM
comparator.
Current-Limit Circuit
The MAX1530/MAX1531 include two current-limit circuits
that use the two MOSFETs’ on-resistances as current-
sensing elements (Figure 4). The high-side MOSFET’s
voltage is used with a fixed 400mV (typ) current- limit
threshold during the high-side on-times. The low-side
MOSFET’s voltage is used with an adjustable current-limit
threshold during the low-side on-times. Using both circuits
together ensures that the current is always measured and
controlled.
The high-side MOSFET current limit employs a peak cur-
rent limit. If the voltage across the high-side MOSFET,
measured from IN to LX, exceeds the 400mV threshold
during an on-time, the high-side MOSFET turns off and
the low-side MOSFET turns on.
The low-side MOSFET current-limit circuit employs a
“valley” current limit. If the voltage across the low-side
MOSFET, measured from LX to PGND, exceeds the low-
side threshold at the end of a low-side on-time, the low-
side MOSFET remains on and the high-side MOSFET
stays off for the entire next cycle.
Maxim Integrated
│ 18
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
The ILIM pin is a dual-mode input. When ILIM is con-
nected to VL, a default low-side current limit of 250mV
typ) is used. If ILIM is connected to a voltage between
250mV and 3V, the low-side current limit is typically 1/5th
the ILIM voltage.
from the VL supply and placed parallel to the high-side
MOSFET’s gate-source terminals.
On startup, the synchronous rectifier (low-side MOS-
FET) forces LX to ground and charges the boost capaci-
tor from VL through diode D1. On the second half-cycle,
the switch-mode power supply turns on the high-side
MOSFET by closing an internal switch between BST and
DH. This provides the necessary gate-to-source voltage
to turn on the high-side switch, an action that boosts the
5V gate-drive signal above the input voltage.
The MAX1530/MAX1531s’ current limits are compara-
tively inaccurate, since the maximum load current is a
function of the MOSFETs’ on-resistances and the induc-
tor value, as well as the accuracy of the two thresholds.
However, using MOSFET current sensing reduces both
cost and circuit size and increases efficiency, since sense
resistors are not needed.
Oscillator Frequency Selection (FREQ)
The FREQ pin can be used to select the switching fre-
quency of the step-down regulator. Connect FREQ to
VL for 500kHz operation. Connect FREQ to AGND for
250kHz operation. The 500kHz operation minimizes the
size of the inductor and capacitors. The 250kHz opera-
tion improves efficiency by 2% to 3%.
MOSFET Gate Drivers (DH, DL)
The DH and DL drivers are optimized for driving mod-
erate-size high-side and low-side MOSFETs. Adaptive
dead-time circuits monitor the DL and DH drivers and
prevent either FET from turning on until the other is fully
off. This algorithm allows operation without shoot- through
with a wide range of MOSFETs, minimizing delays and
maintaining efficiency. When the gates are turning off,
there must be low-resistance, low-induc- tance paths
from the gate drivers to the MOSFET gates for the
adaptive dead-time circuit to work properly. Otherwise,
the sense circuitry in the MAX1530/ MAX1531 interpret
the MOSFET gate as “off” while gate charge actually
remains. Use short, wide traces mea- suring less than 50
squares (at least 20 mil wide if the MOSFET is 1in from
the device). It is advantageous to slow down the turn-on
of both gate drivers if there is noise coupling between the
switching regulator and the linear regulators. The noise
coupling can result in excessive switching ripple on the
linear regulator outputs. Slowing down the turn-on of the
gate drivers proves to be an effective way of reduc- ing
the output ripple. Take care to ensure that the turn- off
times are not affected at the same time. As explained
above, slowing down the turn-off times may result in
shoot-through problems. In Figure 1, a 10Ω resistor (R5)
is inserted in series with the BST pin to slow down the
turn-on of the high-side MOSFET (N1-B) without affecting
the turn-off. A 10Ω resistor (R6) is also inserted between
DL and the gate of the low-side MOS- FET (N1-A) to slow
its turn-on. Because the gate resis- tor would slow down
the turn-off time, connect a switching diode (D2) (such
as 1N4148) in parallel with the gate resistor as shown in
Figure 1 to prevent poten- tial shoot-through.
Linear Regulator Controllers
The MAX1530/MAX1531 include three positive linear
regulator controllers, LR1, LR2, and LR3. These linear
regulator controllers can be used with external pass tran-
sistors to regulate supplies for TFT LCDs. The MAX1531
includes an additional positive linear regula- tor controller
(LR4) and a negative linear regulator con- troller (LR5).
Low-Voltage Logic Regulator Controller (LR1)
LR1 is an analog gain block with an open-drain N- chan-
nel output. It drives an external PNP pass transis- tor
with a 6.8kΩ base-to-emitter resistor. Its guaranteed base
drive sink current is at least 3mA. The regulator including
transistor Q1 in Figure 1 uses a 10µF output capacitor
and is designed to deliver 500mA at 2.5V.
LR1 is typically used to generate low-voltage logic sup-
plies for the timing controller and the digital sections of the
TFT LCD source/gate driver ICs.
LR1 is enabled when the soft-start of the main step-
down regulator is complete. (See the Startup Sequence
(ONL_,SEQ) section.) Each time it is enabled, the con-
troller goes through a soft-start routine that ramps up its
internal reference DAC. (See the Soft-Start section.)
Gamma Regulator Controller (LR2) LR2
is an analog gain block with an open-drain N- channel
output. It drives an external PNP pass transis- tor with a
6.8kΩ base-to-emitter resistor. Its guaranteed base drive
sink current is at least 2mA. The regulator including tran-
sistor Q2 in Figure 1 uses a 0.47µF output capacitor and
is designed to deliver 50mA at 9.7V.
High-Side Gate-Drive Supply (BST)
A flying-capacitor bootstrap circuit generates gate- drive
voltage for the high-side N-channel switch (Figure 1). The
capacitor C5 between BST and LX is alternately charged
Maxim Integrated
│ 19
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
LR2 is typically used to generate the TFT LCD gamma
reference voltage, which is usually 0.3V below the source
drive supply voltage.
LR4 is typically used to generate the TFT LCD source
drive supply voltage. The input for this regulator can come
directly from the input supply, be produced from an exter-
nal step-up regulator, or from an extra winding coupled
to the main step-down regulator inductor. LR4 is enabled
when the step-down regulator is enabled and the voltage
on ONL4 exceeds the ONL4 input threshold (1.238V typ).
(See the Startup Sequence (ONL_,SEQ) section.) Each
time it is enabled, the regulator goes through a soft-start
routine that ramps up its internal reference DAC from 0V
to 1.238V (typ). (See the Soft-Start section.)
LR2 is enabled when the step-down regulator is enabled
and the voltage on ONL2 exceeds ONL2 input threshold
(1.238V typ). (See the Startup Sequence (ONL_,SEQ)
section.) Each time it is enabled, the controller goes
through a soft-start routine that ramps up its internal refer-
ence DAC. (See the Soft-Start section).
Linear Regulator Controller (LR3)
LR3 is an analog gain block with an open-drain Nchannel
output. It drives an external PNP pass transistor with a
6.8kΩ base-to-emitter resistor. Its guaranteed base drive
sink current is at least 2mA. The regulator, including Q3 in
Figure 1, uses a 0.47μF output capacitor and is designed
to deliver 20mA at 25V. The regulator including Q3 in
Figure 2 uses a 4.7μF output capacitor and is designed
to deliver 500mA at 10V.
The standard application circuit in Figure 1 powers the
LR4 regulator directly from the input supply and uses
the MAX1531’s general-purpose overcurrent protection
function to protect the input supply from excessive load
currents. (See the Overcurrent Protection section.)
Gate-Off Regulator Controller (LR5)
(MAX1531 Only)
LR5 is an analog gain block with an open-drain P-channel
output. It drives an external NPN pass transistor with a
6.8kΩ base-to-emitter resistor. Its guaranteed base drive
sink current is at least 2mA. The regulator including Q5 in
Figure 1 uses a 0.47μF output capacitor and is designed
to deliver 10mA at -10V.
For the MAX1531 (Figure 1), LR3 is typically used to
generate the TFT LCD gate driver’s gate-on voltage. A
sufficient input voltage can be produced using a charge-
pump circuit as shown in Figure 1. Note that the voltage
rating of the DRV3 output is 28V. If higher voltages are
present, an external cascode NPN transistor (Q6) should
be used with the emitter connected to DRV3, the base
LR5 is typically used to generate the TFT LCD gate
driver’s gate-off voltage. A negative input voltage can
be produced using a charge-pump circuit as shown in
Figure 1. Use as many stages as necessary to obtain the
required output voltage.
to V (which is the connection point of C1 and R12 in
IN
Figure 1), and the collector to the base of the PNP pass
transistor (Figure 1). For the MAX1530 (Figure 2), LR3 is
typically used to generate the TFT LCD source drive sup-
ply voltage. The input for this regulator can come directly
from the input supply, be produced from an external step-
up regulator, or from an extra windingcoupled to the main
step-down regulator inductor.
LR5 is enabled when the step-down regulator is enabled
and the voltage on ONL5 exceeds the ONL5 input thresh-
old (1.238V typ). (See the Startup Sequence (ONL_,SEQ)
section.) Each time it is enabled, the regulator goes
through a soft-start routine that ramps down its internal
reference DAC from VL to 125mV (typ). (See the Soft-
Start section.)
LR3 is enabled when the step-down regulator is enabled
and the voltage on ONL3 exceeds the ONL3 input thresh-
old (1.238V typ). (See the Startup Sequence (ONL_,SEQ)
section.) Each time it is enabled, the controller goes
through a soft-start routine that ramps up its internal refer-
ence DAC. (See the Soft-Start section.)
Internal 5V Linear Regulator (VL)
All MAX1530/MAX1531 functions, except the thermal
sensor, are internally powered from the on-chip, lowdro-
pout 5V regulator. The maximum regulator input voltage
Source Drive Regulator Controller (LR4)
(MAX1531 Only)
(V ) is 28V. Bypass the regulator’s output (VL) with at
IN
LR4 is an analog gain block with an open-drain Nchannel
output. It drives an external PNP pass transistor with a
1.5kΩ base-to-emitter resistor. Its guaranteed base drive
sink current is at least 10mA. The regulator including Q4
in Figure 1 uses a 4.7μF output capacitor and is designed
to deliver 500mA at 10V. The regulator’s fast transient
response allows it to handle brief peak currents up to 2A.
least a 1μF ceramic capacitor to AGND. The V -to-VL
IN
dropout voltage is typically 200mV, so when V is less
IN
than 5.2V, VL is typically V - 200mV. The internal linear
IN
regulator can source up to 30mA to supply the device,
power the low-side gate driver, charge the external boost
capacitor, and supply small external loads. When driving
particularly large MOSFETs, little or no regulator current
may be available for external loads. For example, when
Maxim Integrated
│ 20
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
switched at 500kHz, large MOSFETs with a total of 40nC
total gate charge would require 40nC × 500kHz, which is
approximately 20mA.
EN > 1.24V
AND
VL > 3.5V
SEQ = HIGH
On/Off Control (EN)
The EN pin has an accurate 1.238V (typ) rising threshold
with 5% hysteresis. The accurate threshold allows it to
be used to monitor the input voltage or other analog sig-
STEP-DOWN
REGULATOR
STARTUP
ONL_
CURRENT
SOURCES ON
SEQUENCE
BLOCK
ENABLED
nals of interest. If V
voltage is less than its threshold,
EN
STEP-DOWN
SOFT-START
DONE
then the step-down regulator and all linear regulators are
turned off. VL and the internal reference remain active
when EN is low to allow an accurate EN threshold.A rising
edge on the pin clears any latched faults except for a ther-
mal fault, which is cleared only by cycling the input power.
ONL2 > 1.24V ONL3 > 1.24V ONL4 > 1.24V ONL5 > 1.24V
LR2
STARTUP
LR1
STARTUP
LR3
LR4
LR5
STARTUP
STARTUP
STARTUP
Figure 5. Startup Conditions
Undervoltage Lockout
If VL drops below 3.4V (typ), the MAX1530/MAX1531
assume that the supply voltage is too low to make valid
decisions. Therefore, the undervoltage lockout (UVLO)
circuitry turns off all the internal bias supplies. Switching
is inhibited, and the DL and DH gate drivers are forced
low. After VL rises above 3.5V (typ), the fault and thermal
shutdown latches are cleared and startup begins if EN is
above its threshold.
ONLa
ONLb
ONLc
ONLd
R3
150kΩ
R2
75kΩ
R1
51kΩ
C1
0.1µF
SEQ
5V
ONLa ONLb ONLc
ONLd
Startup Sequence (ONL_, SEQ)
The MAX1530/MAX1531 are not enabled unless all four
of the following conditions are met: 1) VL exceeds the
UVLO threshold, 2) EN is above 1.238V, 3) the fault latch
is not set, and 4) the thermal shutdown latch is not set.
After all four conditions are met, the step-down controller
starts switching and enables soft-start (Figure 5). After
the step-down regulator soft-start is done, the lowvoltage
logic linear regulator controller (LR1) soft-starts.
1.238V
ONL_
OFF
ON
ON
ON
0V
LRa
LRb
The remaining linear regulator controllers and the
sequence block that can be used to control them are
enabled at the same time as the step-down regulator. The
SEQ logic input is used in combination with the ONL_ pins
to control the startup sequence. When SEQ is high and
the sequence block is enabled, each ONL_ pin sources
2μA (typ). When the voltage on an ONL_ pin reaches
1.238V (typ), its respective linear regulator controller
(LR_) is enabled. When SEQ is low or the sequence block
is not enabled, each ONL_ pin is connected to ground
through a 1.5kΩ internal MOSFET.
OFF
OFF
OFF
OFF
OFF
LRc
LRd
ON
OFF
16ms
OFF
Figure 6. Single-Capacitor Sequence Configuration
The sequence block allows the user to program the start-
up of LR2 to LR5 in any desired sequence. If no capacitor
is placed on an ONL_ pin, its LR_ controller starts imme-
diately after the sequence block is enabled and SEQ goes
high. Placing a 1.5nF capacitor on an ONL_ pin provides
about 1ms delay for the respective LR_ controller. Placing
different size capacitors on each ONL_ pin allows any
arbitrary startup sequence.
An arbitrary startup sequence can also be created witha
single capacitor (Figure 6). Capacitor C1, together with
the 8μA current (2μA per ONL_ pin), is chosen to provide
Maxim Integrated
│ 21
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
the desired delay for the controller that starts last (ONLd).
Using 0.1μF for C1 provides about 16ms total delay.
Because of the 6μA current flowing through R1 (51kΩ),
the voltage on ONLc is 0.31V greater than the voltage on
ONLd and it crosses the 1.238V threshold and enables
its LR_ controller about 4ms before ONLd’s controller.
Similarly, the 4μA current through R2 (75kΩ) and the 2μA
current through R3 (150kΩ) cause their LR_ controllers
to each start about 4ms before the next one. Any desired
sequence and delay can be programmed by calculat-
ing the charge rate of C1 and voltage drops across R1
through R3.
(LR1 to LR5) are below 90% of their normal regulation
point, the MAX1530/MAX1531 activate an internal fault
timer. If the fault condition remains continuously for the
entire fault timer duration, the MAX1530/MAX1531 set
the fault latch, shutting down all the regulator outputs.
Undervoltage faults do not turn off VL. Once the fault
condition is removed, cycling the input voltage or apply-
ing a rising edge on SEQ or EN clears the fault latch and
reactivates the device.
Thermal Protection
The thermal protection limits total power dissipation in the
MAX1530/MAX1531. If the junction temperature exceeds
+160°C, a thermal sensor immediately sets the thermal
fault latch, shutting off all the IC’s outputs including VL,
allowing the device to cool down. The only way to clear
the thermal fault latch is to cycle the input voltage after the
device cools down by at least 15°C.
Soft-Start
The soft-start function controls the slew rate of the out-
put voltages and reduces inrush currents during startup.
Each regulator (step-down, LR1 to LR5) goes through a
soft-start routine after it is enabled. During soft-start, the
reference voltage for each positive regulator gradually
ramps up from 0V to the internal reference in 32 steps.
The reference voltage of the negative regulator ramps
down from VL to 125mV in 32 steps. The total soft-start
period for each regulator is 1024 clock cycles for 250kHz
switching frequency and 2048 clock cycles for 500kHz
switching frequency.
Overcurrent Protection Block (CSH, CSL)
(MAX1531 Only)
The MAX1531 includes an uncommitted overcurrent
protection block that can be used to measure any input
or output current, using a current-sense resistor or other
sense element. If the measured current exceeds the over-
current protection threshold (300mV typ), the MAX1531
immediately sets the undervoltage fault latch, shutting
down all the regulator outputs. Overcurrent faults do not
turn off VL. An internal lowpass filter prevents large cur-
rent transients of short duration (less than 50μs) from set-
ting the latch. Once the overcurrent condition is removed,
cycling the input voltage clears the fault latch and reacti-
vates the device. A rising edge on SEQ or EN also clears
the fault latch.
Reset
The MAX1530/MAX1531 include an open-drain timed
microprocessor supervisor function to ensure proper
startup of digital circuits. The RESET output asserts low
whenever RSTIN is less than the RSTIN trip threshold.
RESET also asserts low when VL is less than the VL
UVLO threshold, EN is low, or the thermal, undervoltage
or overcurrent fault latches are set. RESET enters the
high-impedance state only after RSTIN remains above
the trip threshold for the duration of the reset timeout
period. The state of RESET has no effect on other por-
tions of the IC.
In Figure 1’s circuit, the overcurrent protection is used
with the LR4 source driver regulator since that regulator
is powered directly from the input supply and has no cur-
rent limit of its own. The current-sense resistor is placed
in series with the input supply, before the linear regulator’s
external PNP pass transistor. CSH and CSL are connect-
ed to the positive and negative sides of the sense resistor.
The RSTIN threshold (1.114V typ) is designed to allow
RSTIN to directly connect to any of the MAX1530/
MAX1531s’ feedback input pins, eliminating the need for
an additional resistive divider. Typically, RSTIN is con-
nected to FB or FBL1 to monitor the supply voltage for
digital logic ICs, but it can be used to monitor any desired
output voltage or it can even be used as a general- pur-
pose comparator.
Design Procedures
Main Step-Down Regulator
Inductor Selection
Three key inductor parameters must be specified: induc-
Fault Protection
tance value (L), peak current (I
), and DC resistance
PEAK
(R ). The following equation includes a constant, LIR,
DC
Undervoltage Protection
which is the ratio of peak-to-peak inductor ripple current
to DC load current. A higher LIR value allows smaller
inductance, but results in higher losses and higher ripple.
After its soft-start is done, if the output of the main step-
down regulator or any of the linear-regulator outputs
Maxim Integrated
│ 22
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
A good compromise between size and losses is typically
found at a 30% ripple current to load current ratio (LIR =
0.3), which corresponds to a peak inductor current 1.15
times the DC load current:
low enough that the peak current does not generate
more than 340mV across the MOSFET, even when the
MOSFET is hot. If the MOSFET’s R
is not speci-
DS(ON)
fied at a suitable temperature, use the maximum room
temperature specification and add 0.5% per °C for the
V
×(V − V
OUT
)
OUT
IN
R
increase with temperature:
DS(ON)
L =
V
× f
×I
×LIR
IN SW LOAD(MAX)
I
×R
< 340mV
DS(ON)_HOT
PEAK
where I
is the maximum DC load current, and
LOAD(MAX)
To ensure stable operation of the current-mode PWM,
the minimum current-sense ripple signal should exceed
the switching frequency fSW is 500kHz when FREQ is
tied to VL, and 250kHz when FREQ is tied to AGND. The
exact inductor value is not critical and can be adjusted to
make trade-offs among size, cost, and efficiency. Lower
inductor values minimize size and cost, but they also
increase the output ripple and reduce the efficiency due to
higher peak currents. On the other hand, higher inductor
values increase efficiency, but at some point increased
resistive losses due to extra turns of wire will exceed the
benefit gained from lower AC current levels.
12mV. Since this value depends on the minimum R
DS(ON)
of the high-side MOSFET, which is not typically a speci-
fied parameter, a good rule of thumb is to choose the typi-
cal room temperature R
needed for this:
about 2 times the amount
DS(ON)
I
×R
> 24mV
DS(ON)_TYP
RIPPLE
For example, Figure 6’s circuit is designed for 1.5A and
uses a dual MOSFET (N1) for both the high-side and low-
The inductor’s saturation current must exceed the peak
inductor current. The peak current can be calculated by:
side MOSFETs. Its maximum R
at room tempera-
DS(ON)
ture is 145mΩ and an estimate of its maximum R
DS(ON)
at our chosen maximum temperature of +85°C is 188mΩ.
Since the inductor ripple current is 0.5A, the peak current
through the MOSFET is 1.75A. So the maximum peak
current-sense signal is 330mV, which is less than 340mV.
V
×(V − V
)
OUT
OUT
IN
I
=
RIPPLE
f
×L × V
SW
IN
I
RIPPLE
2
I
= I
+
LOAD(MAX)
PEAK
Using the typical R
of 113mΩ and the ripple cur-
DS(ON)
rent of 0.5A, the current ripple signal for the PWM is
56mV, much greater than the required 24mV.
The inductor’s DC resistance should be low for good effi-
ciency. Find a low-loss inductor having the lowest possible
DC resistance that fits in the allotted dimensions. Ferrite
cores are often the best choice, though powdered iron is
inexpensive and can work well at 250kHz. Shielded-core
geometries help keep noise, EMI, and switching wave-
form jitter low.
The R
of the low-side MOSFET (also N1) provides
DS(ON)
current-limit information during the low-side ontime that
inhibits a high-side on-time if the MOSFET voltage is
too high. The voltage is measured across the low-side
MOSFET from PGND to LX and the threshold is set
by ILIM. To use the preset 250mV (typ) threshold, con-
nect ILIM to VL and choose a MOSFET with R
MOSFET Selection and Current-Limit Setting
DS(ON)
low enough that the “valley” current does not generate
more than 190mV across the MOSFET, even when the
The MAX1530/MAX1531s’ step-down controller drives
two external logic-level N-channel MOSFETs. Since the
MOSFET is hot. If the MOSFET’s R
is not speci-
DS(ON)
R
of each MOSFET is used as a sense resistor to
DS(ON)
fied at a suitable temperature, use the maximum room
temperature specification and add 0.5% per °C for the
provide current-sense signals to the PWM, their R
DS(ON)
values are important considerations in component selec-
tion.
R
increase with temperature:
DS(ON)
The R
of the high-side MOSFET (N1) provides an
I
= I
−I
/ 2
DS(ON)
VALLEY
OUT RIPPLE
inductor current-sense signal for current-mode operation
and also provides a crude maximum current limit during
the high-side on-time that prevents runaway currents if
the inductor saturates. The MOSFET voltage is measured
across the high-side MOSFET from VIN to LX and is lim-
ited to 400mV (typ). To ensure the desired output current
I
×R
< 190mV
DS(ON)_HOT
VALLEY
If the MOSFET’s R
is no need to adjust the current-limit threshold using ILIM.
If the MOSFET’s R is too high, adjust the current-
is lower than necessary, there
DS(ON)
DS(ON)
limit threshold using a resistive-divider between VL and
with sufficient margin, choose a MOSFET with R
DS(ON)
Maxim Integrated
│ 23
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
AGND at ILIM. The threshold is approximately 1/5th the
voltage on ILIM over a range of 0.25V to 3V:
age drop across the capacitor’s ESR caused by the cur-
rent into and out of the capacitor:
V
= V
+ V
RIPPLE
RIPPLE(ESR) RIPPLE(C)
I
×R
< 0.2 × V
× (1− K)
VALLEY
DS(ON)_HOT
ILIM
V
= I
×R
RIPPLE(ESR) RIPPLE
I
ESR
K is the accuracy of the current-limit threshold, which is
20% when the threshold is 250mV.
RIPPLE
V
=
RIPPLE(C)
8× C
× f
OUT
For example, Figure 1’s N1 MOSFET has a maximum
SW
R
at room temperature of 145mΩ and an estimate
DS(ON)
where C
is the output capacitance, and R
is the
ESR
OUT
of its maximum at our chosen maximum temperature of
+85°C is 188mΩ. Since the inductor ripple current is 0.5A,
the valley current through the MOSFET is 1.25A. So the
maximum valley current-sense signal is 235mV, which is
too high to work with the 190mV minimum of the default
current-limit threshold. Adding a divider at ILIM (R12 and
R13) adjusts the ILIM voltage to 1.7V and the current-limit
threshold to 340mV, providing more than adequate mar-
gin for threshold accuracy.
ESR of the output capacitor. In Figure 1’s circuit, the
inductor ripple current is 0.5A. Assume the voltage-ripple
requirement is 2% (peak-to-peak) of the 3.3V output,
which corresponds to 66mV total peak-to-peak ripple.
Assuming that the ESR ripple component and the capaci-
tive ripple component each should be less than 50% of
the 66mV total peak-to-peak ripple, then the ESR should
be less than 66mΩ and the output capacitance should
be more than 7.6μF to meet the total ripple requirement.
A 22μF ceramic capacitor with ESR (including PC board
trace resistance) of 10mΩ is selected for the standard
application circuit in Figure 1, which easily meets the volt-
age ripple requirement.
Input Capacitor
The input filter capacitor reduces peak currents drawn
from the power source and reduce noise and voltage
ripple on the input caused by the regulator’s switching.
It is usually selected according to input ripple current
requirements and voltage rating, rather than capacitance
value. The input voltage and load current determine the
The step-down regulator’s output capacitance and ESR
also affect the voltage undershoot and overshoot when
the load steps up and down abruptly. The undershoot
and overshoot have three components: the voltage steps
caused by ESR, the voltage undershoot and overshoot
due to the current-mode control’s AC load regulation, and
the voltage sag and soar due to the finite capacitance and
inductor slew rate.
RMS input ripple current (I
):
RMS
V
×(V − V )
OUT
OUT
IN
I
= I
×
RMS
LOAD
V
IN
The worst case is I
= 0.5 × I
, which occurs at
LOAD
RMS
The amplitude of the ESR steps is a function of the load
step and the ESR of the output capacitor:
V
IN
= 2 × V
.
OUT
For most applications, ceramic capacitors are used
because of their high ripple current and surge current
capabilities. For long-term reliability, choose an input
capacitor that exhibits less than +10°C temperature rise
at the RMS input current corresponding to the maximum
load current.
V
= ∆I
×R
LOAD ESR
ESR_STEP
The amplitude of the sag due to the finite output capaci-
tance and inductor slew rate is a function of the load
step, the output capacitor value, the inductor value, the
input-to-output voltage differential, and the maximum duty
cycle:
Output Capacitor
The output capacitor and its equivalent series resistance
(ESR) affect the regulator’s loop stability, output ripple volt-
age, and transient response. The Compensation Design
section discusses the output capacitance requirement
based on the loop stability. This section deals with how to
determine the output capacitance and ESR needs accord-
ing to the ripple voltage and load transient requirements.
2
L ×(∆I
)
LOAD
V
=
SAG_LC
2× C
×(V
×D
-V
)
OUT
IN(MIN)
MAX OUT
The amplitude of the undershoot due to the AC load regu-
lation is a function of the high-side MOSFET R , the
, the change of the
slope compensation during the undershoot (ΔSC
DS(ON)
gain of the current-sense amplifierA
VCS
),
UNDER
The output voltage ripple has two components: variations
in the charge stored in the output capacitor, and the volt-
the transconductance of the error amplifier g , the com-
m
Maxim Integrated
│ 24
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
pensation resistor R
the output voltage set point V
, the FB regulation V , and
Characteristics is 170mV. The voltage soar due to finite
capacitance and inductor slew rate is 155mV, and the
voltage overshoot due to the AC load regulation is 167mV.
The total overshoot seen the in the Typical Operating
Characteristics is 200mV.
COMP
FB
:
OUT
A
×R
× ∆I
LOAD
VCS
DS(ON)
V
×
OUT
+∆SC
UNDER
V
=
UNDER_AC
V
×R
× g
COMP
Compensation Design
FB
m
The step-down controller of the MAX1530/MAX1531 uses
a peak current-mode control scheme that regulates the
output voltage by forcing the required current through the
inductor. The MAX1530/MAX1531 use the voltage across
Use the following to calculate the slope compensation
change during the sag:
V
OUT
∆SC
= 437.5mV × D
-
UNDER
the high-side MOSFET’s R
to sense the inductor
UNDER
DS(ON)
V
IN
current. Using the current-sense amplifier’s output signal
and the amplified feedback voltage sensed at FB, the
control loop sets the peak inductor current by:
where D
is the duty cycle at the valley of the sag,
UNDER
which is usually 50%.
The actual undershoot is always equal to or bigger than
(V
-V
)× V × A
OUT OUT(SET) FB
VEA
× A
DS(ON) VCS
I
=
the worst of V
, V
, and V
.
PEAK
ESR_STEP SAG_LC
UNDER_AC
V
×R
OUT(SET)
The amplitude of the soar due to the finite output capaci-
tance and inductor slew rate is a function of the load step,
the output capacitor value, the inductor value, and the
output voltage:
where V = 1.238V is the FB regulation voltage, A
the gain of the current-sense amplifier (3.5 typical), AVEA
is
VCS
FB
is the DC gain of the error amplifier (2000 typ), V
OUT(SET)
is the on-
2
L ×(∆I
)
LOAD
× V
is the output voltage set point, and R
resistance of the high-side MOSFET.
DS(ON)
V
=
SOAR_LC
2× C
OUT
OUT
The total DC loop gain (A ) is approximately:
DC
The amplitude of the overshoot due to the AC load regu-
lation is:
V
×R × A
LE VEA
FB
A
=
DC
V
×R
× A
DS(ON) VCS
OUT(SET)
A
×R
× ∆I
LOAD
VCS
DS(ON)
V
×
OUT
+∆SC
OVER
RLE is the equivalent load resistance, given by:
V
=
OVER_AC
V
×R
× g
COMP
FB
m
V
L × f
SW
n ×D'- D
||
OUT
LOAD(MAX)
R
=
where ΔSC
is the change of the slope compensa-
LE
OVER
I
tion during the overshoot, given by:
In the above equation, D’ = 1 - D, n is a factor determined-
by the slope compensation mc and the inductor current
ramp m1, as shown below:
V
OUT
∆SC
= 437.5mV ×
- D
OVER
OVER
V
IN
where D
shoot, which is typically 0%.
is the duty cycle at the peak of the over-
OVER
m
C
n =1 +
m
1
Similarly, the actual overshoot is always equal to or
bigger than the worst of V
, V
, and
The slope compensation of the MAX1530/MAX1531 is
219mV/μs. The inductor current ramp is a function of
the input voltage, output voltage, inductance, high-side
ESR_STEP
SOAR_LC
V
.
OVER_AC
Given the component values in the circuit of Figure 1,
during a 1.5A step load transient, the voltage step due to
capacitor ESR is negligible. The voltage sag due to finite
capacitance and inductor slew rate is 81mV, and the volt-
age undershoot due to the AC load regulation is 170mV.
The total undershoot seen in the Typical Operating
MOSFET on-resistance R
, and the gain of the
DS(ON)
current-sense amplifier A
, and is:
VCS
V
-V
IN OUT
L
m =
×R
× A
DS(ON) VCS
1
Maxim Integrated
│ 25
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Current-mode control has the effect of splitting the com-
plex pole pair of the output LC filter into a single low-
frequency pole and a single high-frequency pole. The
low-frequency current-mode pole depends on output
Unnecessarily high bandwidth can increase noise sen-
sitivity while providing little benefit. Good transient
response with low amounts of output capacitance is
achieved with a crossover frequency between 20kHz
and 100kHz. The series compensation capacitor (C10)
generates a dominant pole that sets the desired cross-
over frequency. Determine C10 using the following
expression:
capacitor C
and the equivalent load resistance R
,
OUT
LE
given by the following:
1
f
=
POLE(LOW)
2µ ×R × C
LE
OUT
g
× A
DC
m
C10 ≈
The high-frequency current-mode pole is given by:
2µ × f
× A
VEA
CROSSOVER
f
where g is the error amplifier’s transconductance
m
(100μS typ).
SW
f
=
POLE(HIGH)
2µ ×n ×D'
2) The compensation resistor R11, together with capaci-
tor C10, provides a zero that is used to cancel the low-
frequency current-mode pole. Determine R11 using
the following expression:
The COMP pin, which is the output of the IC’s internal
transconductance error amplifier, is used to stabilize the
control loop. A series resistor (R11) and capacitor (C10)
are connected between COMP and AGND to form a
pole-zero pair. Another pole-zero pair can be added by
connecting a feed-forward capacitor (C23) in parallel with
feedback resistor R1. The compensation resistor and
capacitors are selected to optimize the loop stability.
1
R11 ≈
2µ × f
× C10
POLE(LOW)
3) Because the error amplifier has limited output current
(16μA typ), small values of R11 can prevent the error
amplifier from providing an immediate COMP voltage
change required for good transient response with mini-
mal output capacitance. If the calculated R11 value
is less than 100kΩ, use 100kΩ and recalculate C10
using the following formula:
The compensation capacitor (C10) creates a dominant
pole at very low frequency (a few hertz). The zero formed
by R11 and C10 cancels the low-frequency current-
mode pole. The zero formed by R1 and C23 cancels
the high-frequency current-mode pole and introduces a
preferable higher frequency pole. In applications where
ceramic capacitors are used, the ESR zero is usually
not a concern because the ESR zero occurs at very high
frequency. If the ESR zero does not occur at a frequency
at least one decade above the crossover, connect a sec-
ond parallel capacitor (C2) between COMP and AGND to
cancel the ESR zero. The component values shown in the
standard application circuits (Figure 1 and Figure 2) yield
stable operation and fast transient response over a broad
range of input-to-output voltages.
1
C10 ≈
2µ× f
×100kΩ
POLE(LOW)
Changing C10 also changes the crossover frequency;
the new crossover frequency is:
g
× A
DC
m
f
=
CROSSOVER
2µ × C10 × A
VEA
To design a compensation network for other components
or applications, use the following procedure to achieve
stable operation:
The calculated crossover frequency should be less
than 1/5th the switching frequency. There are two
ways to lower the crossover frequency if the calculated
value is greater than 1/5th the switching frequency:
1) Select the crossover frequency f
(band-
CROSSOVER
width) to be 1/5th the switching frequency f
or less:
SW
increase the high-side MOSFET R
, or increase
DS(ON)
the output capacitance. Increasing R
reduces
DS(ON)
f
SW
5
f
≤
the DC loop gain, which results in lower crossover
frequency. Increasing output capacitance reduces the
frequency of the lower low-frequency current-mode
CROSSOVER
Maxim Integrated
│ 26
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
pole, which also results in lower crossover frequency.
The following formula gives the crossover frequency
5) For most applications using tantalum or polymer
capacitors, the output capacitor’s ESR forms a second
zero that occurs either below or close to the crossover
frequency. The zero must be cancelled with a pole.
Verify the frequency of the output capacitor’s ESR
zero, which is:
as a function the MOSFET R
capacitance:
and the output
DS(ON)
g
× V ×R11
FB
m
f
=
CROSSOVER
2µ × A
× V
× C
×R
OUT DS(ON)
VCS
OUT(SET)
1
f
=
Change one or both of these circuit parameters to
obtain the desired crossover. Recalculate ADC and
repeat steps 1 to 3 after making the changes.
ZERO(ESR)
2µ × C
×R
ESR
OUT
where R
is the ESR of the output capacitor C
.
OUT
ESR
4) If f
is less than the crossover frequency,
If the output capacitor’s ESR zero does not occur well
after the crossover, add the parallel compensation
capacitor (C2) to form another pole to cancel the ESR
zero. Calculate the value of C2 using:
POLE(HIGH)
cancel the pole with a feed-forward zero. Determine
the value of C23 (feedback capacitor) using the follow-
ing:
1
C10
C23 ≈
C2 ≈
2µ × f
×R1
POLE(HIGH)
2µ× f
×R11× C10-1
ZERO(ESR)
C23 also forms a secondary pole with R1 and R2
given by the following:
Applications using ceramic capacitors usually have ESR
zeros that occur at least one decade above the crossover.
Since the ESR zero of ceramic capacitors has little effect
on the loop stability, it does not need to be cancelled.
1
f
=
POLE_SEC
2µ × R1 | | R 2 × C 2 3
(
)
The following is an example. In the circuit of Figure 1, the
input voltage is 12V, the output voltage is set to 3.3V, the
maximum load current is 1.5A, the typical onresistance
of the high-side MOSFET is 100mΩ, and the inductor is
10μH. The calculated equivalent load resistance is 1.67Ω.
The DC loop gain is:
The frequency of this pole should be above the cross-
over frequency for loop stability. The position of this
pole is related to the high-frequency currentmode pole,
which is determined by the inductor current ramp sig-
nal. The inductor current ramp signal must satisfy the
following condition to ensure the pole occurs above
the crossover frequency:
1.238V ×1.67Ω × 2000
3.3V ×100mΩ × 3.5
A
≈
= 4180
DC
2π ×D'×R2× f
×m
C
CROSSOVER
m1 >
If the chosen crossover frequency is 20kHz (step 1):
R1+ R2 × f
- 2π ×D'×R2× f
CROSSOVER
(
)
SW
If the frequency of the secondary pole is below the
crossover frequency, the frequency of the second-
ary pole must be moved higher, or the crossover
frequency must be moved lower. There are two ways
to increase the frequency of the secondary pole:
100µS× 4180
2µ× 20kHz × 2000
C10 ≈
≈ 1.7nF
With a 22μF output capacitor, the output pole of the step-
down regulator is (step 2):
increase the high-side MOSFET R
, or reduce
DS(ON)
the step-down inductance, L. As explained before, for
given input and output voltages, the current ramp sig-
1
f
=
= 4.3kHz
POLE(OUT)
2µ× 22µF×1.67Ω
nal is proportional to the high-side MOSFET R
,
DS(ON)
and inversely proportional to the inductance. If the
pole occurs below the crossover frequency, the cur-
Calculate R11 using:
rent feedback signal is too small. Increasing R
DS(ON)
1
or reducing the inductance can increase the current
feedback signal. To lower the crossover frequency, use
the methods described in step 3. Repeat steps 1 to 4
after making the changes.
R11≈
= 22kΩ
2µ× 4.3kHz ×1.7nF
Maxim Integrated
│ 27
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Because R11 is less than 100kΩ, use 100kΩ for R11 and
recalculate C10 as (step 3):
Charge Pumps
Selecting the Number of Charge-Pump Stages
For highest efficiency, always choose the lowest number
of charge-pump stages that meet the output requirement.
The number of positive charge-pump stages is given by:
1
C10 ≈
= 370pF
2µ× 4.3kHz ×100kΩ
Use the standard value of 470pF for C10 and recalculate
the crossover frequency as:
V
+ V
− V
POS
DROPOUT IN
− 2× V
D
N
=
POS
V
IN
100µS× 4180
2µ× 470pF× 2000
where N
stages, V
is the number of positive charge-pump
POS
POS
f
≈
= 70.8kHz
CROSSOVER
is the positive charge-pump output, V
IN
is the input voltage of the step-down regulator, V is
the forward voltage drop of the charge-pump diode, and
D
Since the crossover frequency is less than 1/5th the
switching frequency, 470pF is an acceptable value for
C10.
V
is the dropout margin for the linear regulator.
DROPOUT
Use V
= 0.3V. The number of negative charge-
DROPOUT
Because the high-frequency pole of the current-mode
control is at 64kHz, the feed-forward capacitor is (step 4):
pump stages is given by:
−V
+ V
DROPOUT
NEG
V
N
=
NEG
1
− 2× V
D
IN
C23 ≈
= 140pF
2µ× 64kHz ×17.8kΩ
where N
stages, V
is the number of negative charge-pump
is the negative charge-pump output, VIN
is the input voltage of the step-down regulator, V is
NEG
NEG
Use a standard value of 150pF for C23. The pole formed
by C23, R1 and R2 occur at 159kHz, above the 70.8kHz
crossover frequency.
D
the forward voltage drop of the charge-pump diode, and
V
is the dropout margin for the linear regulator.
DROPOUT
Because a ceramic output capacitor is used in the circuit
of Figure1, the ESR zero occurs well above the crossover
frequency, so no additional compensation capacitor (C2)
is needed (step 5).
Use V
= 0.3V.
DROPOUT
The above equations are derived based on the assump-
tion that the first stage of the positive charge pump is con-
nected to V and the first stage of the negative charge
pump is connected to ground. Sometimes fractional
stages are more desirable for better efficiency. This can
IN
Output Voltage Selection
The MAX1530/MAX1531 step-down regulator’s output
voltage can be adjusted by connecting a resistive voltage-
divider from the output to AGND with the center tap con-
nected to FB (Figure 1). Select R2 in the 5kΩ to 50kΩ
range. Calculate R1 with the following equation:
be done by connecting the first stage to V
or another
OUT
available supply. If the first stage of the positive charger
pump is powered from the output of the step-down regula-
tor V , then the equation becomes:
OUT
V
OUT
−V
+ V
− V
POS
DROPOUT OUT
− 2× V
D
R1 = R2 ×
where V = 1.238V, and V
−1
N
=
POS
V
FB
V
IN
may vary from 1.238V to
OUT
FB
If the first stage of the negative charge pump is powered
from the output of the step-down regulator V
equation becomes:
approximately 0.6 × V (V is up to 28V).
IN IN
, then the
OUT
Boost-Supply Diode
A signal diode, such as the 1N4148, works well in most
applications. If the input voltage goes below 6V, use
a small 100mA Schottky diode for slightly improved ef
ficiency and dropout characteristics. Do not use power di
odes, such as the 1N5817 or 1N4001, since high junction
capacitance can charge up VL to excessive voltages.
−V
+ V
+ V
NEG
DROPOUT
OUT
N
=
NEG
V
− 2× V
IN
D
Maxim Integrated
│ 28
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
to VL with the center tap connected to FBL5 (Figure 1).
Select R29 in the 10kΩ to 30kΩ range.Calculate R28 with
the following equation:
Flying Capacitors
Increasing the flying capacitor value lowers the effec-
tive source impedance and increases the output current
capability. Increasing the capacitance indefinitely has a
negligible effect on output current capability because the
internal switch resistance and the diode impedance place
a lower limit on the source impedance. A 0.1μF ceramic
capacitor works well in most low-current applications.
The voltage rating for a given flying capacitor (CX) must
exceed the following:
R28 = R29× V
− V
) / (V − V
GOFF L FBL5
(
)
FBL5
where V
= 125mV and V = 5.0V.
L
FBL5
Pass Transistor Selection
The pass transistor must meet specifications for DC cur-
rent gain (hFE), collector-emitter saturation voltage, and
power dissipation. The transistor’s current gain limits the
guaranteed maximum output current to:
V
> N x V
IN
CX
where N is the stage number in which the flying capaci-
tor appears, and V is the input voltage of the stepdown
IN
regulator.
V
R
BE
I
= I
−
×h
FE
LOAD(MAX)
DRV
BE
Charge-Pump Output Capacitors
Increasing the output capacitance or decreasing the ESR
reduces the charge pump output ripple voltage and the
peak-to-peak transient voltage. With ceramic capacitors,
the output voltage ripple is dominated by the capacitance
value. Use the following equation to approximate the
required capacitor value:
where I
is the minimum guaranteed base drive cur-
is the base-emitter voltage of the pass transis-
DRV
rent, V
BE
tor, and R is the pullup resistor connected between the
BE
transistor’s base and emitter. Furthermore, the transis-
tor’s current gain increases the linear regulator’s DC loop
gain (see the Stability Requirements section), which may
destabilize the output. Therefore, transistors with current
gain over 300 at the maximum output current can be diffi-
cult to stabilize and are not recommended unless the high
gain is needed to meet the load current requirements.
LOAD
≥
OUT
2f
V
OSC RIPPLE
where V
ripple.
is the peak-to-peak value of the output
RIPPLE
The transistor’s saturation voltage at the maximum output
current determines the minimum input-to-output voltage
differential that the linear regulator supports. Also, the
package’s power dissipation limits the usable maximum
input-to-output voltage differential. The maximum power
dissipation capability of the transistor’s package and
mounting must exceed the actual power dissipation in the
device. The power dissipation equals the maximum load
Charge-Pump Rectifier Diodes
Use low-cost silicon switching diodes with a current rating
equal to or greater than 2 times the average charge-pump
input current. If it helps avoid an extra stage, some or all
of the diodes can be replaced with Schottky diodes with
an equivalent current rating.
current (I
) times the maximum input-to-output
LOAD(MAX)
Linear Regulator Controllers
Output Voltage Selection
voltage differential:
P = I
×(V
− V
)
LOAD(MAX)
LRIN(MAX)
LROUT
Adjust the positive linear regulator (LR1 to LR4) output
voltages by connecting a resistive voltage-divider from the
output to AGND with the center tap connected to FBL_
(Figure 1). Select the lower resistor of the divider in the
10kΩ to 30kΩ range. Calculate the upper resistor with the
following equation:
where V
is the maximum input voltage of the
LRIN(MAX)
linear regulator, and V
linear regulator.
is the output voltage of the
LROUT
Output Voltage Ripple
Ideally, the output voltage of a linear regulator should
not contain any ripple. In the MAX1530/MAX1531, the
step-down regulator’s switching noise can couple to the
linear regulators, creating output voltage ripple. Following
the PC board layout guidelines in the PC Board Layout
and Grounding section can significantly reduce noise
× V
R
= R
/ V
−1
UPPER
LOWER
OUT_
FBL_
where V
is 1.238V (typ).
FBL_
Adjust the negative linear regulator (LR5) output voltage
by connecting a resistive voltage-divider from V
GOFF
Maxim Integrated
│ 29
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
coupling. If there is still an unacceptable amount of ripple
after the PC board layout has been optimized, consider
increasing output capacitance. Adding more capacitance
does not eliminate the ripple, but proportionally reduces
the amplitude of the ripple. If increasing the output capaci-
tance is not desirable because of space or cost concerns,
then consider slowing the turn-on of the step-down
DC-to-DC MOSFETs. Slower turn-on leads to smoother
LX rising and falling edges and consequently reduces the
switching noise. When slowing down MOSFET turn-on,
ensure the turn-off time is not affected. Otherwise, the
adaptive dead-time circuitry may not work properly and
shoot-through may occur. See the MOSFET Gate Drivers
section for details on how to slow down the turn-on of both
DH and DL.
The output capacitor and the load resistance create the
dominant pole in the system. However, the internal ampli-
fier delay, the pass transistor’s input capacitance, and the
stray capacitance at the feedback node create additional
poles in the system, and the output capacitor’s ESR gen-
erates a zero. For proper operation, use the following
steps to ensure the linear regulator’s stability:
1) First, calculate the dominant pole set by the linear
regulator’s output capacitor and the load resistor:
1
f
=
POLE(LR)
2µC
R
LR LOAD
where C is the output capacitance of the linear regu-
LR
lator and R
is the load resistance corresponding
LOAD
to the maximum load current.
Stability Requirements
The unity-gain crossover of the linear regulator is:
The MAX1530/MAX1531 linear-regulator controllers use
an internal transconductance amplifier to drive an external
pass transistor. The transconductance amplifier, the pass
transistor, the base-emitter resistor, and the output capac-
itor determine loop stability. The following applies equally
to all linear regulators in the MAX1530 and MAX1531.
Any differences are highlighted where appropriate.
f
= A
f
V(LDO) POLE(LDO)
CROSSOVER
2) The pole created by the internal amplifier delay is
about 1MHz:
f
≅ 1M H z
POLE(AMP)
3) Next, calculate the pole set by the transistor’s input
capacitance, the transistor’s input resistance, and the
base-to-emitter pullup resistor
The transconductance amplifier regulates the output volt-
age by controlling the pass transistor’s base current. The
total DC loop gain is approximately:
1
f
=
)
POLE(C
IN
I
×h
FE
4
2µC (R
|| R
)
IN
BIAS
I
IN BE
A
≈
× 1+
× V
REF
V(LR)
V
T
LOAD
g
h
FE
g
m
m
where C
=
,R = R
=
, g is the
m
IN
IN
µ
where V is 26mV at room temperature, I
output current of the linear regulator, V
regulator’s internal reference voltage, and I
current through the base-to-emitter resistor (R ). Each
of the linear regulator controllers is designed for a differ-
ent maximum output current so they have different output
drive currents and different bias currents (IBIAS). Each
controller’s bias current can be found in the Electrical
Characteristics. The current listed in the Conditions col-
umn for the FBL_ regulation voltage specification is the
individual controller’s bias current. The base-to-emitter
resistor for each controller should be chosen to set the
is the
2µf
T
LOAD
is the linear
T
REF
transconductance of the pass transistor, and f is the
T
transition frequency. Both parameters can be found
in the transistor’s data sheet. Because R
greater than R , the above equation can be simpli-
is the
BIAS
BE
is much
BE
IN
fied:
1
2µC R
f
≈
)
POLE(C
IN
IN IN
The equation can be further simplified:
correct I
:
BIAS
POLE(C
)
IN
FE
V
BE
R
=
BE
I
BIAS
Maxim Integrated
│ 30
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
4) Next, calculate the pole set by each linear regulator’s
together at only one location, which is a via connected
to the backside pad of the device. All voltage-feedback
dividers should be connected to the analog ground
island. The step-down regulator’s input and output
capacitors, and the charge pump components should
be a wide power ground plane. The power ground
plane should be connected to the power ground pin
(PGND) with a wide trace. Maximizing the width of the
power ground traces improves efficiency, and reduces
output voltage ripple and noise spikes. All other ground
connections, such as the VL and IN pin bypass capaci-
tor and the linear regulator output capacitors, should
be star-connected to the backside of the device with
wide traces. Make no other connections between
these separate ground planes.
feedback resistance and the capacitance (C
)
FBL_
between FBL_ and AGND (approximately 5pF includ-
ing stray capacitance):
1
f
f
f
f
f
=
POLE(FBL1)
POLE(FBL2)
POLE(FBL3)
POLE(FBL4)
POLE(FBL5)
2µC
(R9 || R10)
1
FBL1
=
2µC
2µC
2µC
2µC
(R18 || R19)
FBL2
1
=
=
=
(R25 ||R26)
FBL3
FBL4
FBL5
1
and
(R22 ||R23)
1
(R28 ||R29)
3) Place the IN pin and VL pin bypass capacitors within
5mm from the IC and connect them to their respective
pins with short, direct connections.
5) Next, calculate the zero caused by the output capaci-
tor’s ESR:
4) Since both MOSFETs are used for current sensing,
care must be taken to ensure that noise and DC errors
do not corrupt the sense signals. Place both MOSFETs
close to the IC. Connect PGND to the source of the
low-side MOSFET with a short, wide trace. Connect
DL to the gate of the low-side MOSFET with a short,
wide trace. Ensure that the traces from DL to low-side
MOSFET to PGND total no more than 50 squares.
Connect LX close to the connection point between
the low-side and highside MOSFETs with a short,
wide trace. Connect DH to the gate of the high-side
MOSFET with a short, wide trace. Ensure that the
traces from DH to high-side MOSFET to LX total no
more than 50 squares (50 squares corresponds to 20
mils wide if the total trace is 1in long).
1
f
=
ESR_ZERO
2µC
R
LR ESR
where R
is the equivalent series resistance of
ESR
C
.
LR
6) To ensure stability, choose C
large enough so that
LR
the crossover occurs well before the poles and zero
calculated in steps 2) to 5). The poles in steps 3) and
4) generally occur at several megahertz and using
ceramic capacitors ensures the ESR zero occurs at
several megahertz as well. Placing the crossover
below 500kHz is sufficient to avoid the amplifier-delay
pole and generally works well, unless unusual com-
ponent choices or extra capacitances move the other
poles or zero below 1MHz.
5) Place all feedback voltage-divider resistors as close
to their respective feedback pins as possible. The
divider’s center trace should be kept short. Placing the
resistors far away causes their FB traces to become
antennas that can pick up switching noise. Care
should be taken to avoid running any feedback trace
near LX or the switching nodes in the charge pumps.
PC Board Layout and Grounding
Careful PC board layout is important for proper operation.
Use the following guidelines for good PC board layout:
1) Place the high-power components of the step-down
regulator (input capacitors, MOSFETs, inductor, and
output capacitors) first, with any grounded connec-
tions adjacent. Connect these components with short,
wide traces. Avoid using vias in the high-current paths.
If vias are unavoidable, use many vias in parallel to
reduce resistance and inductance.
6) Minimize the length and maximize the width of the
traces between the output capacitors and the load for
best transient responses.
7) Minimize the size of the LX node while keeping it wide
and short. Keep the LX node away from feedback
nodes and analog ground. Use DC traces as shield if
necessary.
2) Create islands for the analog ground (AGND), power
ground (PGND), and individual linear regulator
grounds. Connect all these ground areas (islands)
Maxim Integrated
│ 31
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Pin Configuration
Chip Information
PROCESS: BiCMOS
TOP VIEW
+
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
DRV2
FBL2
1
2
3
4
5
6
7
8
24 BST
23 DH
FBL3
22 LX
DRV3
CSH*
CSL*
21 DL
MAX1530
MAX1531
20 PGND
19 ONL5*
18 ONL4*
17 ONL3
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN
32 TQFN-EP
T3255+4
21-0140
90-0012
FBL4*
DRV4*
* = N.C. FOR MAX1530
THIN QFN
Maxim Integrated
│ 32
www.maximintegrated.com
MAX1530/MAX1531
Multiple-Output Power-Supply
Controllers for LCD Monitors
Revision History
REVISION REVISION
PAGES
CHANGED
DESCRIPTION
NUMBER
DATE
0
1
2
3
0
Initial release
—
11/09
12/10
3/14
Changing an existing part to an automotive-qualified part (/V)
Removed the /V part from Ordering Information and minor edits
Removed automotive reference from the Applications section
1, 13, 32, 33, 34
3, 4
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
©
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
2014 Maxim Integrated Products, Inc.
│ 33
相关型号:
MAX1534ETE+T
Switching Regulator, 2A, 200kHz Switching Freq-Max, BICMOS, 4 X 4 MM, 0.80 MM HEIGHT, QFN-16
MAXIM
©2020 ICPDF网 联系我们和版权申明