MAX16043 [MAXIM]
Dual-/Triple-/Quad-Voltage, Capacitor-Adjustable, Sequencing/Supervisory Circuits; 双/三/四电压,电容调节,排序/监控电路型号: | MAX16043 |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Dual-/Triple-/Quad-Voltage, Capacitor-Adjustable, Sequencing/Supervisory Circuits |
文件: | 总15页 (文件大小:270K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-0622; Rev 0; 8/06
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
General Description
Features
o 2.2V to 28V Operating Voltage Range
The MAX16041/MAX16042/MAX16043 are dual-/triple-/
quad-voltage monitors and sequencers that are offered
in a small thin QFN package. These devices offer enor-
mous design flexibility as they allow fixed and
adjustable thresholds to be selected through logic
inputs and provide sequence timing through small
external capacitors. These versatile devices are ideal
for use in a wide variety of multivoltage applications.
o Fixed Thresholds for 3.3V, 2.5V, 1.8V, 1.5V, and
1.2V Systems
o 1.5% Accurate Adjustable Threshold Monitors
Voltages Down to 0.5V
o 2.7% Accurate Fixed Thresholds Over
Temperature
o Fixed (140ms min)/Capacitor-Adjustable Delay
As the voltage at each monitored input exceeds its
respective threshold, its corresponding output goes
high after a propagation delay or a capacitor-set time
delay. When a voltage falls below its threshold, its
respective output goes low after a propagation delay.
Each detector circuit also includes its own enable input,
allowing the power-good outputs to be shut off inde-
pendently. The independent output for each detector
has an open-drain configuration capable of supporting
voltages up to 28V, thereby allowing them to interface
to shutdown and enable inputs of various DC-DC regu-
lators. Each detector can operate independently as four
separate supervisory circuits or can be daisy-chained
to provide controlled power-supply sequencing.
Timing
o Independent Open-Drain Outputs/Push-Pull
RESET Output
o Enable Inputs for Each Monitored Voltage
o 9 Logic-Selectable Threshold Options
o Manual Reset and Tolerance Select (5%/10%) Inputs
o Small, 4mm x 4mm TQFN Package
o Fully Specified from -40°C to +125°C
Ordering Information
PIN-
PKG
PART*
TEMP RANGE
PACKAGE
CODE
The MAX16041/MAX16042/MAX16043 also include a
push-pull reset function that deasserts only after all of
the independently monitored voltages exceed their
threshold. The reset timeout is internally fixed or can be
adjusted externally. These devices are offered in a
4mm x 4mm TQFN package and are fully specified
from -40°C to +125°C.
MAX16041TE+
MAX16042TP+
MAX16043TG+
-40°C to +125°C 16 TQFN
-40°C to +125°C 20 TQFN
-40°C to +125°C 24 TQFN
T1644-4
T2044-3
T2444-4
+Denotes lead-free package.
*For tape and reel, add a “T” after the “+.” All tape and reel
orders are available in 2.5k increments.
Pin Configurations
Applications
Multivoltage Systems
TOP VIEW
DC-DC Supplies
18
17
16
15
14
13
Servers/Workstations
12
11
10
9
MR 19
CRESET 20
CDLY4 21
CDLY3 22
TH1
EN4
EN3
Storage Systems
Networking/Telecommunication Equipment
MAX16043
Selector Guide
EN2
EN1
GND
MONITORED INDEPENDENT
VOLTAGES
RESET
CDLY2
CDLY1
23
8
PART
OUTPUTS
OUTPUT
24
7
MAX16041
MAX16042
MAX16043
2
3
4
2 (Open-drain)
3 (Open-drain)
4 (Open-drain)
Push-pull
Push-pull
Push-pull
+
1
2
3
4
5
6
TQFN
(4mm x 4mm)
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND.)
Continuous Power Dissipation (T = +70°C)
A
V
.........................................................................-0.3V to +30V
16-Pin TQFN (derate 25mW/°C above +70°C) ...........2000mW
20-Pin TQFN (derate 25.6mW/°C above +70°C) ........2051mW
24-Pin TQFN (derate 27.8mW/°C above +70°C) ........2222mW
Operating Temperature Range .........................-40°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
CC
EN1–EN4 ....................................................-0.3V to (V
OUT1–OUT4...........................................................-0.3V to +30V
RESET.........................................................-0.3V to (V
IN1–IN4.......................................................-0.3V to (V
MR, TOL, TH1, TH0 ....................................-0.3V to (V
CDLY1–CDLY4.........................................................-0.3V to +6V
CRESET......................................................-0.3V to (V + 0.3V)
+ 0.3V)
CC
+ 0.3V)
+ 0.3V)
+ 0.3V)
CC
CC
CC
CC
Input/Output Current (all pins).......................................... 20mA
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
= 2.2V to 28V, T = -40°C to +125°C, unless otherwise specified. Typical values are at V
= 3.3V and T = +25°C.) (Note 1)
CC A
CC
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SUPPLY
Operating Voltage Range
Undervoltage Lockout
V
(Note 2)
(Note 2)
2.2
1.8
28.0
2.0
V
V
CC
UVLO
1.9
50
Undervoltage-Lockout Hysteresis UVLO
V
falling
CC
mV
HYST
V
V
V
= 3.3V
= 12V
= 28V
40
47
52
75
75
80
CC
CC
CC
All OUT_ and RESET at
logic-high (IN_ current
excluded)
V
Supply Current
I
CC
µA
CC
INPUTS (IN_)
3.3V threshold, TOL = GND
3.3V threshold, TOL = V
2.970
2.805
2.250
2.125
1.620
1.530
1.350
1.275
1.080
1.020
0.492
0.463
3.052
2.888
2.313
2.187
1.665
1.575
1.387
1.312
1.110
1.050
0.5
3.135
2.970
2.375
2.250
1.710
1.620
1.425
1.350
1.140
1.080
0.508
0.481
2/MAX16043
CC
2.5V threshold, TOL = GND
2.5V threshold, TOL = V
CC
1.8V threshold, TOL = GND
1.8V threshold, TOL = V
IN_ Thresholds (IN_ Falling)
V
V
V
V
TH
CC
1.5V threshold, TOL = GND
1.5V threshold, TOL = V
CC
1.2V threshold, TOL = GND
1.2V threshold, TOL = V
TOL = GND
CC
Adjustable Threshold
(IN_ Falling)
TH
TOL = V
0.472
0.5
CC
IN_ Hysteresis (IN_ Rising)
IN_ Input Resistance
IN_ Input Current
V
%
HYST
Fixed threshold
Adjustable threshold only (V
500
918
kΩ
nA
I
= 1V)
IN_
-100
+100
L
2
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
ELECTRICAL CHARACTERISTICS (continued)
(V
= 2.2V to 28V, T = -40°C to +125°C, unless otherwise specified. Typical values are at V
= 3.3V and T = +25°C.) (Note 1)
CC A
CC
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
CRESET AND CDLY_
CRESET Threshold
V
CRESET rising, V
= 3.3V
0.465
380
0.5
500
1
0.535
620
V
TH-RESET
CC
CRESET Charge Current
CDLY_ Threshold
I
V
= 3.3V
nA
V
CH-RESET
CC
V
CDLY_ rising, V
= 3.3V
CC
0.95
200
1.05
300
TH-CDLY
CDLY_ Charge Current
I
V
= 3.3V
250
nA
CH-CDLY
CC
DIGITAL LOGIC INPUTS (EN_, MR, TOL, TH1, TH0)
Input Low Voltage
V
0.4
V
V
V
IL
Input High Voltage
V
1.4
-1
IH
TH1, TH0 Logic-Input Floating
0.6
TOL, TH1, TH0 Logic-Input
Current
V
, V
, V
= GND or V
+1
µA
TOL TH1 TH0
CC
EN_ Input Leakage Current
MR Internal Pullup Current
OUTPUTS (OUT_, RESET)
V
V
= V
or GND
CC
-100
250
+100
820
nA
nA
EN_
CC
= 3.3V
535
V
V
V
V
V
≥ 1.2V, I
= 90µA
SINK
0.3
0.3
CC
CC
CC
CC
CC
Output Low Voltage
(Open-Drain or Push-Pull)
V
V
≥ 2.25V, I
= 0.5mA
OL
SINK
≥ 4.5V, I
= 1mA
0.35
SINK
≥ 3V, I
= 500µA
0.8 x V
0.8 x V
SOURCE
CC
CC
Output High Voltage (Push-Pull)
V
V
OH
≥ 4.5V, I
= 800µA
SOURCE
Output Leakage Current
(Open-Drain)
I
Output not asserted low, V
= 28V
OUT
1
µA
ms
LKG
CRESET = V , V
= 3.3V
140
190
260
CC CC
Reset Timeout Period
TIMING
t
RP
CRESET open
0.030
t
IN_ rising, CDLY_ open
IN_ falling, CDLY_ open
CRESET open, IN_ falling
(Note 3)
35
20
35
DELAY+
IN_ to OUT_ Propagation Delay
µs
t
DELAY-
IN_ to RESET Propagation Delay
MR Minimum Input Pulse Width
EN_ or MR Glitch Rejection
t
µs
µs
ns
RST-DELAY
2
280
3
t
From device enabled to device disabled
OFF
EN_ to OUT_ Delay
µs
From device disabled to device enabled
(CDLY_ open)
t
30
3
ON
MR to RESET Delay
MR falling
µs
Note 1: Devices are production tested at T = +25°C. Limits over temperature are guaranteed by design.
A
Note 2: Operating below the UVLO causes all outputs to go low. The outputs are guaranteed to be in the correct state for V
down
CC
to 1.2V.
Note 3: To guarantee an assertion, the minimum input pulse width must be greater than 2µs.
_______________________________________________________________________________________
3
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
Typical Operating Characteristics
(V
= 3.3V, T = +25°C, unless otherwise noted.)
A
CC
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SUPPLY CURRENT
vs. TEMPERATURE
NORMALIZED ADJUSTABLE THRESHOLD
vs. TEMPERATURE
60
1.003
1.002
1.001
1.000
0.999
0.998
0.997
0.996
0.995
0.994
0.993
0.992
0.991
0.990
60
55
50
45
40
35
30
MAX16041
V
= 28V
CC
MAX16041
TOL = V
CC
55
50
45
40
35
30
TOL = GND
V
= 12V
CC
V
= 3.3V
CC
ADJUSTABLE THRESHOLD
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
20 35 50 65 80 95 110 125
2
6
10
14
18
22
26
30
TEMPERATURE (°C)
TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
RESET TIMEOUT PERIOD
NORMALIZED ADJUSTABLE THRESHOLD
vs. TEMPERATURE
vs. C
OUT_ DELAY vs. C
CRESET
CDLY_
1.003
1.002
1.001
1.000
0.999
0.998
0.997
0.996
0.995
0.994
0.993
0.992
0.991
0.990
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
TOL = V
CC
TOL = GND
2/MAX16043
3.3V THRESHOLD
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
0
100 200 300 400 500 600 700 800 900 1000
0
100 200 300 400 500 600 700 800 900 1000
(nF)
TEMPERATURE (°C)
C
(nF)
C
CRESET
CDLY_
RESET OUTPUT LOW VOLTAGE
vs. SINK CURRENT
OUT_ LOW VOLTAGE
vs. SINK CURRENT
FIXED RESET TIMEOUT PERIOD
vs. TEMPERATURE
1.0
0.8
0.6
0.4
0.2
0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
190
189
188
187
186
185
184
183
182
181
180
CRESET = V
CC
0
1
2
3
4
6
7
0
1
2
3
4
5
6
7
5
-40 -25 -10
5
20 35 50 65 80 95 110 125
TEMPERATURE (°C)
SINK CURRENT (mA)
SINK CURRENT (mA)
4
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
Typical Operating Characteristics (continued)
(V
= 3.3V, T = +25°C, unless otherwise noted.)
A
CC
RESET OUTPUT HIGH VOLTAGE
vs. SOURCE CURRENT
ENABLE TURN-ON
ENABLE TURN-OFF
MAX16041 toc12
MAX16041 toc11
3.5
CRESET = V
CDLY_ = OPEN
CC
CRESET = V
CDLY_ = OPEN
CC
3.0
2.5
2.0
1.5
1.0
0.5
0
EN_
5V/div
EN_
5V/div
OUT_
5V/div
OUT_
5V/div
RESET
5V/div
RESET
5V/div
40ms/div
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
SOURCE CURRENT (mA)
4µs/div
RESET TIMEOUT DELAY
MR FALLING vs. RESET
MAX16041 toc14
MAX16041 toc13
CRESET = V
CRESET = V
CC
CC
CDLY_ = OPEN
CDLY_ = OPEN
IN_
5V/div
MR
5V/div
OUT_
5V/div
RESET
5V/div
RESET
5V/div
100ms/div
4µs/div
MAXIMUM TRANSIENT DURATION
vs. THRESHOLD OVERDRIVE
MR RISING vs. RESET
MAX16041 toc15
100
90
80
70
60
50
40
30
20
10
0
OUTPUT ASSERTED ABOVE THIS LINE
CRESET = V
CDLY_ = OPEN
CC
MR
5V/div
RESET
5V/div
1
10
100
1000
40ms/div
THRESHOLD OVERDRIVE (mV)
_______________________________________________________________________________________
5
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
Pin Description
PIN
NAME
FUNCTION
MAX16041 MAX16042 MAX16043
Supply Voltage Input. Connect a 2.2V to 28V supply voltage to power the
1
2
1
2
1
2
3
4
5
V
device. All outputs are low when V
is below the UVLO. For noisy systems,
CC
CC
bypass V
to GND with a 0.1µF capacitor.
CC
Monitored Input 1. When the voltage at IN1 exceeds its threshold, OUT1 goes
high after the capacitor-adjustable delay period. When the voltage at IN1 falls
below its threshold, OUT1 goes low after a propagation delay.
IN1
IN2
IN3
IN4
Monitored Input 2. When the voltage at IN2 exceeds its threshold, OUT2 goes
high after the capacitor-adjustable delay period. When the voltage at IN2 falls
below its threshold, OUT2 goes low after a propagation delay.
3
3
Monitored Input 3. When the voltage at IN3 exceeds its threshold, OUT3 goes
high after the capacitor-adjustable delay period. When the voltage at IN3 falls
below its threshold, OUT3 goes low after a propagation delay.
—
—
4
Monitored Input 4. When the voltage at IN4 exceeds its threshold, OUT4 goes
high after the capacitor-adjustable delay period. When the voltage at IN4 falls
below its threshold, OUT4 goes low after a propagation delay.
—
Threshold Tolerance Input. Connect TOL to GND to select thresholds 5%
4
5
5
6
6
7
TOL
below nominal. Connect TOL to V
to select thresholds 10% below nominal.
CC
GND
Ground
Active-High Logic-Enable Input 1. Driving EN1 low causes OUT1 to go low
regardless of the input voltage. Drive EN1 high to enable the monitoring
comparator.
6
7
7
8
8
9
EN1
EN2
EN3
EN4
Active-High Logic-Enable Input 2. Driving EN2 low causes OUT2 to go low
regardless of the input voltage. Drive EN2 high to enable the monitoring
comparator.
2/MAX16043
Active-High Logic-Enable Input 3. Driving EN3 low causes OUT3 to go low
regardless of the input voltage. Drive EN3 high to enable the monitoring
comparator.
—
—
9
10
11
Active-High Logic-Enable Input 4. Driving EN4 low causes OUT4 to go low
regardless of the input voltage. Drive EN4 high to enable the monitoring
comparator.
—
Threshold Select Input 1. Connect TH1 to V
select the input-voltage threshold option in conjunction with TH0 (see Table 2).
or GND, or leave it open to
CC
8
9
10
11
—
12
13
12
13
14
15
16
TH1
TH0
Threshold Select Input 0. Connect TH0 to V or GND, or leave it open to
select the input-voltage threshold option in conjunction with TH1 (see Table 2).
CC
Output 4. When the voltage at IN4 is below its threshold or EN4 goes low,
OUT4 goes low.
—
—
10
OUT4
OUT3
OUT2
Output 3. When the voltage at IN3 is below its threshold or EN3 goes low,
OUT3 goes low.
Output 2. When the voltage at IN2 is below its threshold or EN2 goes low,
OUT2 goes low.
6
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
Pin Description (continued)
PIN
NAME
FUNCTION
MAX16041 MAX16042 MAX16043
Output 1. When the voltage at IN1 is below its threshold or EN1 goes low,
OUT1 goes low.
11
14
15
17
OUT1
Active-Low Reset Output. RESET asserts low when any of the monitored
voltages (IN_) falls below its respective threshold, any EN_ goes low, or MR is
RESET asserted. RESET remains asserted for the reset timeout period after all of the
monitored voltages exceed their respective threshold, all EN_ are high, all
OUT_ are high, and MR is deasserted.
12
18
Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET
13
14
16
17
19
20
MR
remains low for the reset timeout period after MR is deasserted (as long as all
OUT_ are high).
Capacitor-Adjustable Reset Delay Input. Connect an external capacitor from
CRESET to GND to set the reset timeout period or connect to V
for the
CC
CRESET
default 140ms minimum reset timeout period. Leave CRESET open for internal
propagation delay.
Capacitor-Adjustable Delay Input 4. Connect an external capacitor from
—
—
15
—
18
19
21
22
23
CDLY4 CDLY4 to GND to set the IN4 to OUT4 (and EN4 to OUT4) delay period.
Leave CDLY4 open for internal propagation delay.
Capacitor-Adjustable Delay Input 3. Connect an external capacitor from
CDLY3 CDLY3 to GND to set the IN3 to OUT3 (and EN3 to OUT3) delay period.
Leave CDLY3 open for internal propagation delay.
Capacitor-Adjustable Delay Input 2. Connect an external capacitor from
CDLY2
CDLY2 to GND to set the IN2 to OUT2 (and EN2 to OUT2) delay period.
Leave CDLY2 open for internal propagation delay.
Capacitor-Adjustable Delay Input 1. Connect an external capacitor from
CDLY1 to GND to set the IN1 to OUT1 (and EN1 to OUT1) delay period.
Leave CDLY1 open for internal propagation delay.
16
—
20
—
24
—
CDLY1
EP
Exposed Pad. EP is internally connected to GND. Connect EP to the
ground plane.
voltages exceed their respective thresholds, an inde-
pendent reset output deasserts to allow the system
processor to operate.
Detailed Description
The MAX16041/MAX16042/MAX16043 are low-voltage,
accurate, dual-/triple-/quad-voltage microprocessor
(µP) supervisors in a small TQFN package. These
devices provide supervisory and sequencing functions
for complex multivoltage systems. The MAX16041 mon-
itors two voltages, the MAX16042 monitors three volt-
ages, and the MAX16043 monitors four voltages.
These devices offer enormous flexibility as there are
nine threshold options that are selected through two
threshold-select logic inputs. Each monitor circuit also
offers an independent enable input to allow both digital
and analog control of each monitor output. A tolerance
select input allows these devices to be used in systems
requiring 5% or 10% power-supply tolerances. In addi-
tion, the time delays and reset timeout can be adjusted
using small capacitors. There is also a fixed 140ms
minimum reset timeout feature.
The MAX16041/MAX16042/MAX16043 offer indepen-
dent outputs and enable functions for each monitored
voltage. This configuration allows the device to operate as
four separate supervisory circuits or be daisy-chained
together to allow controlled sequencing of power supplies
during power-up initialization. When all of the monitored
_______________________________________________________________________________________
7
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
TH0
TH1
EN4 EN3 EN2 EN1
DELAY
THRESHOLD
SELECT
LOGIC
IN1
IN2
IN3
250nA
OUT1
LOGIC
DRIVER
1V
MAX16043
OUT2
DELAY
DRIVER
DELAY
OUT3
DRIVER
2/MAX16043
IN4
OUT4
DELAY
DRIVER
DRIVER
GND
TOL
RESET
DELAY
LOGIC
RESET
REFERENCE
V
CDLY1
CDLY2
CDLY3
CDLY4
CRESET
MR
CC
Figure 1. MAX16043 Simplified Functional Diagram
8
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
V
CC
V
UVLO
IN_
V
TH
V
TH
t < t
ON
EN_
OUT_
t
DELAY-
t
t
ON
ON
t
DELAY+
t
OFF
t
RST_DELAY
t
t
RP
t
RP
RP
RESET
Figure 2. Timing Diagram (CDLY_ Open)
shown in Figure 3 and use the following equation to cal-
culate the threshold voltage:
Applications Information
Tolerance
The MAX16041/MAX16042/MAX16043 feature a pin-
selectable threshold tolerance. Connect TOL to GND to
select the thresholds 5% below the nominal value.
R1
R2
⎛
⎝
⎞
V
= V × 1+
⎜
TH
⎟
⎠
INTH
Connect TOL to V
to select the threshold tolerance
CC
Choosing the proper external resistors is a balance
between accuracy and power use. The input to the volt-
age monitor is a high-impedance input with a small
100nA leakage current. This leakage current contributes
to the overall error of the threshold voltage where the out-
put is asserted. This induced error is proportional to the
value of the resistors used to set the threshold. With lower
value resistors, this error is reduced, but the amount of
power consumed in the resistors increases.
10% below the nominal voltage. Do not leave TOL uncon-
nected.
Adjustable Input
These devices offer several monitoring options with both
fixed and/or adjustable reset thresholds (see Table 2).
For the adjustable threshold inputs, the threshold voltage
(V ) at each adjustable IN_ input is typically 0.5V (TOL
TH
= GND) or 0.472V (TOL = V ). To monitor a voltage
CC
V
, connect a resistive divider network to the circuit as
INTH
_______________________________________________________________________________________
9
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
OUT_ Output
V
INTH
The MAX16041/MAX16042/MAX16043 feature open-drain
outputs. An OUT_ goes low when its respective IN_ input
voltage drops below its specified threshold or when its
EN_ goes low (see Table 1). OUT_ goes high when EN_
R1
R2
MAX16041
MAX16042
MAX16043
IN_
is high and V
is above its threshold after a time delay.
Open-drain outputs require an external pullup resistor to
any voltage from 0 to 28V.
IN_
Table 1. Output State*
EN_
Low
High
Low
High
IN_
< V
OUT_
V
TH
V
V
V
V
Low
Low
Low
IN_
IN_
IN_
IN_
TH
TH
TH
TH
V
V
INTH
< V
> V
> V
-1
)
R1 = R2 x
(
TH
OUT_ = high impedance
*When V
falls below the UVLO, all outputs go low regardless
CC
Figure 3. Setting the Adjustable Input
of the state of EN_ and V . The outputs are guaranteed to be
IN_
in the correct state for V
down to 1.2V.
CC
The following equation is provided to help estimate the
value of the resistors based on the amount of acceptable
error:
Table 2. Input-Voltage Threshold Selector
e
× V
INTH
IN1 (ALL
IN2 (ALL
IN3
IN4
A
R1=
TH1/TH0
LOGIC
VERSIONS) VERSIONS) (MAX16042) (MAX16043)
I
L
(V)
(V)
(V)
(V)
where e is the fraction of the maximum acceptable
A
Low/Low
3.3
3.3
3.3
3.3
2.5
3.3
3.3
2.5
Adj
2.5
1.8
1.5
1.2
1.8
Adj
Adj
Adj
Adj
1.8
Adj
Adj
1.8
Adj
2.5
Adj
Adj
Adj
1.5
Adj
Adj
2.5
Adj
Adj
Adj
Adj
Adj
absolute resistive divider error attributable to the input
Low/High
Low/Open
High/Low
High/High
High/Open
Open/Low
Open/High
Open/Open
leakage current (use 0.01 for 1%), V
is the voltage
INTH
at which the output (OUT_) should assert, and I is the
L
worst-case IN_ leakage current (see the Electrical
Characteristics). Calculate R2 as follows:
2/MAX16043
V
×R1
− V
TH
TH
R2 =
V
INTH
Unused Inputs
Connect any unused IN_ and EN_ inputs to V
RESET Output
.
CC
RESET asserts low when any of the monitored voltages
(IN_) falls below its respective threshold, any EN_ goes
low, or MR is asserted. RESET remains asserted for the
reset timeout period after all of the monitored voltages
exceed their respective thresholds, all EN_ are high, all
OUT_ are high, and MR is deasserted. All devices have
a push-pull, active-low reset output.
10 ______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
Adjustable Reset Timeout Period
(CRESET)
Connect a normally open momentary switch from MR to
GND to create a manual-reset function. External
debounce circuitry is not required. If MR is driven from
long cables or if the device is used in a noisy environ-
ment, connect a 0.1µF capacitor from MR to GND to
provide additional noise immunity.
All of these parts offer an internally fixed reset timeout
(140ms min) by connecting CRESET to V . The reset
CC
timeout can also be adjusted by connecting a capaci-
tor from CRESET to GND. When the voltage at CRESET
reaches 0.5V, RESET goes high. When RESET goes
high, CRESET is immediately held low.
Pullup Resistor Values
The exact value of the pullup resistors for the open-
drain outputs is not critical, but some consideration
should be made to ensure the proper logic levels
when the device is sinking current. For example, if
Calculate the reset timeout period as follows:
V
V
= 2.25V and the pullup voltage is 28V, keep the
+ 30 ×10−6
CC
TH−RESET
t
=
× C
CRESET
RP
sink current less than 0.5mA as shown in the Electrical
Characteristics. As a result, the pullup resistor should
be greater than 56kΩ. For a 12V pullup, the resistor
should be larger than 24kΩ. Note that the ability to sink
I
CH−RESET
where V
is 0.5V, I
CRESET
is 0.5µA, t
is in
TH-RESET
seconds, and C
CH-RESET
is in Farads. To ensure timing
RP
current is dependent on the V
supply voltage.
CC
accuracy and proper operation, minimize leakage at
C
.
CRESET
Power-Supply Bypassing
The device operates with a V supply voltage from
CC
Adjustable Delay (CDLY_)
When V rises above V with EN_ high, the internal
2.2V to 28V. When V
falls below the UVLO threshold,
CC
IN
TH
all the outputs go low and stay low until V
falls below
CC
250nA current source begins charging an external
capacitor connected from CDLY_ to GND. When the
voltage at CDLY_ reaches 1V, OUT_ goes high. When
OUT_ goes high, CDLY_ is immediately held low.
1.2V. For noisy systems or fast rising transients on V
,
CC
connect a 0.1µF ceramic capacitor from V
to GND
CC
as close to the device as possible to provide better
noise and transient immunity.
Adjust the delay (t
) from when V rises above
IN
DELAY
V
TH
(with EN_ high) to OUT_ going high according to
the equation:
Ensuring Valid Reset Output
with V
Down to 0V
CC
V
TH−CDLY
t
=
× C
+ 35 ×10−6
CDLY
When V
falls below 1.2V, the ability for the output to
CC
DELAY
I
CH−CDLY
sink current decreases. To ensure a valid output as
V
CC
falls to 0V, connect a 100kΩ resistor from RESET
where V
is 1V, I
DELAY
is 0.25µA, C
is in
TH-CDLY
Farads, and t
CH-CDLY
is in seconds. To ensure timing
CDLY
to GND.
accuracy and proper operation, minimize leakage
at CDLY.
Typical Application Circuits
Figures 4 and 5 show typical applications for the
MAX16041/MAX16042/MAX16043. In high-power appli-
cations, using an n-channel device reduces the loss
across the MOSFETs as it offers a lower drain-to-source
on-resistance. However, an n-channel MOSFET
Manual-Reset Input (MR)
Many µP-based products require manual-reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic-low on MR
asserts RESET low. RESET remains asserted while MR
is low and during the reset timeout period (140ms fixed
or capacitor adjustable) after MR returns high. The MR
input has a 500nA internal pullup, so it can be left
unconnected, if not used. MR can be driven with TTL or
CMOS logic levels, or with open-drain/collector outputs.
requires a sufficient V
voltage to fully enhance it for a
GS
low R
. The application in Figure 4 shows the
DS_ON
MAX16042 configured in a multiple-output sequencing
application. Figure 5 shows the MAX16043 in a power-
supply sequencing application using n-channel
MOSFETs.
______________________________________________________________________________________ 11
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
3.3V
+1.8V
+1.5V
+2.5V
IN
DC-DC OUT
EN
IN
DC-DC OUT
EN
IN
DC-DC OUT
EN
EN1
IN1
IN2
IN3
OUT3
OUT1 EN2
OUT2 EN3
V
CC
TH0
TH1
MAX16042
MR
SYSTEM
RESET
RESET
CDLY1
CDLY3
CRESET
GND
TOL
CDLY2
Figure 4. Sequencing Multiple-Voltage System
12V
BUS
1.5V
1.8V
2.5V
2/MAX16043
TO
LOADS
3.3V
IN4
IN1
IN3
OUT3
OUT1
IN2
OUT2
V
CC
OUT4
EN1
EN2
EN3
EN4
MAX16043
SYSTEM
RESET
RESET
MR
CRESET
GND
TOL
TH0
TH1
CDLY1
CDLY3
CDLY4
CDLY2
Figure 5. Multiple-Voltage Sequencing Using n-Channel FETs
12 ______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
Pin Configurations (continued)
TOP VIEW
12
11
10
9
15
14
13
12
11
TH1
EN3
10
9
MR 16
CRESET 17
CDLY3 18
TH1
8
7
6
5
MR 13
CRESET 14
EN2
EN1
GND
8
EN2
EN1
GND
MAX16041
MAX16042
CDLY2
CDLY1
15
16
CDLY2
CDLY1
7
19
20
6
+
+
1
2
3
4
1
2
3
4
5
TQFN
(4mm x 4mm)
TQFN
(4mm x 4mm)
Chip Information
PROCESS: BICMOS
______________________________________________________________________________________ 13
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
2/MAX16043
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
1
E
21-0139
2
14 ______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, Capacitor-
Adjustable, Sequencing/Supervisory Circuits
2/MAX16043
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
2
E
21-0139
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
相关型号:
MAX16046
12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAXIM
MAX16046A
12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAXIM
MAX16046ACB+
12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAXIM
MAX16046ATN+
12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAXIM
MAX16046ECB+
12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAXIM
MAX16046ECB+T
Power Supply Management Circuit, Adjustable, 12 Channel, BICMOS, PQFP64, TQFP-64
MAXIM
MAX16046ETN+
12-Channel/8-Channel EEPROM-Programmable System Managers with Nonvolatile Fault Registers
MAXIM
©2020 ICPDF网 联系我们和版权申明