MAX17062EVKIT [MAXIM]
1.2MHz Switching Frequency (Selectable: 640kHz or 1.2MHz);型号: | MAX17062EVKIT |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | 1.2MHz Switching Frequency (Selectable: 640kHz or 1.2MHz) |
文件: | 总7页 (文件大小:131K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-2446; Rev 1; 6/08
MAX17062 Evaluation Kit
Evluates:MAX17062
General Description
Features
o 90% Efficiency
The MAX17062 evaluation kit (EV kit) is a fully assem-
bled and tested surface-mount PCB that provides the
voltages required for active-matrix, thin-film transistor
(TFT), liquid-crystal displays (LCDs). The EV kit con-
tains a pulse-width-modulated (PWM) step-up switch-
ing regulator, a positive single-stage charge pump for
the TFT gate-on supply, and a negative single-stage
charge pump for the TFT gate-off supply.
o +2.6V to +5.5V Input Range
o Output Voltage Adjustable from VIN to 20V
o Output Voltages (+4.5V to +5.5V Input)
+15V Output at 600mA
+29V Output at 30mA (Positive Charge Pump)
-15V Output at 30mA (Negative Charge Pump)
The EV kit operates from a DC supply voltage of +4.5V
to +5.5V and is configured to operate with a switching
frequency of 1.2MHz. The step-up switching regulator
is configured for a +15V output and can provide 600mA
with a +4.5V input. The positive charge pump is config-
ured for a +29V output providing 30mA. The negative
charge pump is configured for a -15V output providing
30mA.
o 1.2MHz Switching Frequency (Selectable: 640kHz
or 1.2MHz)
o Programmable Soft-Start
o 0.01µA IC Shutdown Current (typ)
o Fully Assembled and Tested
The MAX17062 EV kit features low-quiescent current
and high-conversion efficiency (90%). The high switch-
ing frequency allows the use of small, surface-mount
components.
Ordering Information
PART
TYPE
MAX17062EVKIT+
EV Kit
+Denotes lead-free and RoHS compliant.
Component List
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
4.7µF 10%, 10V X5R ceramic
capacitors (0603)
TDK C1608X5R1A475K
10µF 10%, 25V X5R ceramic
capacitors (1210)
Murata GRM32DR61E106K
TDK C3225X5R1E106K
C1, C2
2
C7, C8
2
1µF 10%, 6.3V X5R ceramic
capacitor (0603)
Murata GRM188R60J105K
TDK C1068X7R1C105K
C9
0
0
Not installed, ceramic capacitor (1210)
C3
1
Not installed, aluminum electrolytic
capacitor (SMT: 6.3mm x 6mm)
C10
0.033µF 10%, 25V X7R ceramic
capacitor (0603)
Murata GRM188R71E333K
TDK C1608X7R1H333K
0.22µF 10%, 50V X7R ceramic
capacitors (0805)
Murata GRM21BR71H224K
TDK C2012X7R1H224K
C4
C5
1
C11, C15
C12, C14
2
2
560pF 5%, 50V C0G ceramic
capacitor (0603)
Murata GRM1885C1H561J
TDK C1608C0G1H561J
0.1µF 10%, 50V X7R ceramic
capacitors (0603)
Murata GRM188R71H104K
TDK C1608X7R1H104K
1
0
C6, C13, C16,
C17
Not installed, ceramic capacitors
(0603)
C18
D1
0
1
Not installed, ceramic capacitor (0805)
3A, 30V Schottky diode (M-Flat)
Toshiba CMS03 (TE12L-Q) LEAD FREE
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX17062 Evaluation Kit
Component List (continued)
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
100kΩ 5% resistor (0603)
47kΩ 5% resistor (0603)
20kΩ 1% resistor (0603)
221kΩ 1% resistor (0603)
10Ω 5% resistor (0603)
Not installed, resistor (0603)
0Ω 5% resistor (0603)
R1
R2
R3
R4
R5
R6
R7
1
1
1
1
1
0
1
250mA, 90V dual ultra-fast diodes
(SOT23)
Central Semiconductor CMPD1001S
LEAD FREE (Top Mark: L21)
Diodes Inc. BAV99 (300mA, 100V)
D2, D4
2
D3
0
1
Not installed, diode (SOT23)
2-pin header (0.1in centers)
JU1
Not installed, 3-pin header—short
(0.1in centers)
JU2
JU3
0
0
High-performance step-up
DC-DC controller (10 TDFN-EP*)
Maxim MAX17062ETB+
U1
1
Not installed, 2-pin header—short
(0.1in centers)
—
1
1
Shunt
2.7µH 20% power inductor
TOKO FDV0630-2R7 (27mΩ, 4.4A)
Sumida CDRH5D18BHPNP-2R7M
(65mΩ, 3.9A)
—
PCB: MAX17062 Evaluation Kit+
L1
1
*EP = Exposed pad.
Evluates:MAX17062
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Central Semiconductor
Diodes, Inc.
631-435-1110
805-446-4800
770-436-1300
847-545-6700
847-803-6100
847-297-0070
www.centralsemi.com
www.diodes.com
Murata Electronics North America, Inc.
Sumida Corp.
www.murata-northamerica.com
www.sumida.com
TDK Corp.
www.component.tdk.com
www.tokoam.com
TOKO America, Inc.
Note: Indicate that you are using the MAX17062 when contacting these component suppliers.
2) Connect the positive terminal of the DC power sup-
Quick Start
Recommended Equipment
Before beginning, the following equipment is needed:
ply to the VIN pad. Connect the negative terminal of
the DC power supply to the PGND pad.
3) Turn on the +4.5V to +5.5V DC power supply and
verify that the step-up switching regulator output
(VOUT) is +15V.
•
•
+4.5V to +5.5V, 5A DC power supply (VIN)
Voltmeter
4) Verify that the gate-on supply (VGON) is approxi-
mately +29V.
Procedure
The MAX17062 EV kit is fully assembled and tested. Follow
these steps to verify board operation. Caution: Do not
turn on the power supply until all connections are
completed.
5) Verify that the gate-off supply (VGOFF) is approxi-
mately -15V.
1) Verify that there is no shunt placed across jumper
JU1 to enable the MAX17062.
2
_______________________________________________________________________________________
MAX17062 Evaluation Kit
Evluates:MAX17062
Switching-Frequency
Detailed Description
Selection (FREQ)
The MAX17062 EV kit contains a high-efficiency, pulse-
width-modulated (PWM), step-up switching regulator, a
positive single-stage unregulated charge pump, and a
negative single-stage unregulated charge pump. The
MAX17062 features a programmable soft-start, loop-
compensation pin, and an internal MOSFET switch.
The EV kit operates from a +4.5V to +5.5V DC power
supply.
The MAX17062 EV kit provides the option to configure
the switching frequency of the step-up DC-DC convert-
er. Table 2 lists jumper JU2 settings for configuring the
switching frequency. The EV kit is configured and
shipped to operate at 1.2MHz. For operation at
640kHz, cut the trace between pins 1 and 2 of jumper
JU2 and short pins 2 and 3. Refer to the MAX17062
data sheet for selecting the proper components.
As configured, the step-up switching regulator gener-
ates a +15V output (VOUT) and can provide 600mA
with a 4.5V input. The step-up switching regulator out-
put voltage can be adjusted from VIN to +20V by
changing the values of the feedback resistors (see the
Evaluating Other Output Voltages section).
Table 2. Jumper JU2 Functions
SHUNT
POSITION
SWITCHING
FREQUENCY
FREQ PIN
Connected to VIN with a
PC trace
1-2*
2-3
1.2MHz
640kHz
The VGON supply consists of a single positive charge-
pump stage to generate approximately twice the VOUT
voltage (or approximately +29V) and provide 30mA.
The VGOFF supply consists of a single negative
charge-pump stage to generate approximately -VOUT
(or approximately -15V) and provide 30mA.
Connected to GND (cut the
trace between pins 1-2
before shorting pins 2-3)
*Default position.
Evaluating Other
Output Voltages
The MAX17062 EV kit’s step-up switching-regulator
output (VOUT) is set to +15V by feedback resistors R3
and R4. To generate output voltages other than +15V
(VIN to +20V), select different external voltage-divider
resistors, R3 and R4. Select R3 in the 10kΩ to 50kΩ
range. R4 is then given by:
The EV kit is configured for a +4.5V input and a 1.2MHz
switching frequency. Operation at a different input
voltage, output voltage (VOUT), or switching fre-
quency may require a different inductor, output
capacitors, and compensation components. Refer to
the MAX17062 IC data sheet for detailed information on
loop compensation and component selection.
Jumper Selection
Shutdown Mode (SHDN)
⎡
⎢
⎤
⎛
⎞
VOUT
The EV kit features a shutdown mode that reduces the
R4 = R3 x
−1
⎥
⎜
⎟
V
⎝
⎢
⎣
⎠
FB
⎥
⎦
MAX17062 quiescent current. JU1 selects the shut-
down mode. See Table 1 for jumper JU1 functions.
where V = 1.24V. Note that changing the VOUT volt-
FB
Table 1. Jumper JU1 Functions
age also changes the VGON and VGOFF charge-pump
output voltages. For significantly different operation
points, the EV kit may require a different inductor and
component changes. Refer to the MAX17062 data
sheet for proper component selection.
SHUNT
POSITION
SHDN PIN
MAX17062 OUTPUT
Shutdown mode,
VOUT = VIN - V
Installed
Connected to GND
DIODE
Connected to VIN
through R1
MAX17062 enabled,
VOUT = +15V
Not installed*
*Default position.
_______________________________________________________________________________________
3
MAX17062 Evaluation Kit
Positive Charge-Pump
Table 3. Two-Stage Charge-Pump
Components
Configuration
As configured, the single-stage positive charge pump
generates approximately double the VOUT output voltage
at VGON. The charge pump can be reconfigured as a
two-stage positive charge pump, providing triple the
VOUT output voltage at VGON. This is accomplished by
installing capacitors C13, C16, diode D3, and removing
resistor R7. See Table 3 for suggested component values.
DESIGNATION QTY
DESCRIPTION
0.1µF 10%, 50V X7R ceramic
capacitors (0603)
C13, C16
2
250mA, 90V dual ultra-fast diode
(SOT23)
D3
R7
1
0
Not installed, resistor
Evluates:MAX17062
4
_______________________________________________________________________________________
MAX17062 Evaluation Kit
Evluates:MAX17062
Figure 1. MAX17062 EV Kit Schematic
_______________________________________________________________________________________
5
MAX17062 Evaluation Kit
Evluates:MAX17062
Figure 2. MAX17062 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX17062 EV Kit PCB Layout—Component Side
Figure 4. MAX17062 EV Kit PCB Layout—Solder Side
6
_______________________________________________________________________________________
MAX17062 Evaluation Kit
Evluates:MAX17062
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
DESCRIPTION
CHANGED
0
11/07
Initial release
—
Schematic changes: added EP to U1 and changed ground of C3 from PGND to
AGND.
1
6/08
5
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 7
© 2008 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
相关型号:
MAX1706C
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706C/D
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706D
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
MAX1706EEE
1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator
MAXIM
©2020 ICPDF网 联系我们和版权申明