MAX17122EVKIT [MAXIM]
Greater than 94% Efficiency (Step-Up Switching Regulator);型号: | MAX17122EVKIT |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Greater than 94% Efficiency (Step-Up Switching Regulator) |
文件: | 总7页 (文件大小:628K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-5089; Rev 0; 12/09
MAX17122 Evaluation Kit
General Description
Features
The MAX17122 evaluation kit (EV kit) is a fully assembled
and tested surface-mount PCB that provides the voltages
and features required for thin-film transistor (TFT), liquid-
crystal display (LCD) TV panels. The EV kit includes a
step-down regulator, step-up regulator, negative output
buck-boost regulator, positive regulated charge pump,
and a negative linear regulator.
S +10V to +14V Input Range
S 750kHz Switching Frequency
S Output Voltages
+15V Output at 2.2A (Step-Up Switching
Regulator)
+3.3V Output at 2.5A (Step-Down Switching
Regulator)
The MAX17122 IC operates from +10V to +14V input
voltages and is optimized for LCD TV panels running
directly from +12V supplies. The step-up switching
regulator is configured for a +15V output that provides at
least 2.2A with an input voltage of +12V. The step-down
regulator is configured for a +3.3V output that provides
at least 2.5A and the buck-boost is configured for a
temperature-variable -12V to -20V output that provides
at least 450mA. The positive regulated charge pump is
configured for a +28V output providing at least 100mA.
The negative linear regulator is configured for a -7.5V
output providing at least 100mA.
-12V to -20V Output at 450mA (Temperature-
Variable Buck-Boost Switching Regulator)
+28V Output at 100mA (Positive Charge Pump)
-7.5V Output at 100mA (Negative Linear
Regulator)
+5V Output at 25mA (Linear Regulator VL)
S Greater than 94% Efficiency (Step-Up Switching
Regulator)
S Fully Assembled and Tested
Ordering Information
PART
TYPE
MAX17122EVKIT+
EV Kit
+Denotes lead(Pb)-free and RoHS compliant.
Component List
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
22FF Q20%, 16V X5R ceramic
capacitors (1206)
Murata GRM31CR61C226M
Taiyo Yuden EMK316BJ226M
1FF Q10%, 25V X5R ceramic
capacitors (0603)
Murata GRM188R61E105K
TDK C1608X5R1E105M
C1, C2
2
4
1
2
C6, C16
2
0
1
C7, C8, C15,
C23, C24, C25
Not installed, ceramic capacitors
(0603)
0.1FF Q10%, 50V X7R ceramic
capacitors (0603)
Murata GRM188R71H104K
TDK C1608X7R1H104K
C3, C9, C11,
C13
2.2FF Q10%, 16V X5R ceramic
capacitor (0603)
Murata GRM188R61C225K
TDK C1608Y5V1C225ZT
C12
C14
C17
22FF Q20%, 6.3V X5R ceramic
capacitor (0805)
Murata GRM21BR60J226M
TDK C2012X5R0J226K
C4
1FF Q10%, 50V X7R ceramic
capacitor (1206)
Murata GRM31MR71H105KA
TDK C3216X7R1H105K
1
1
0.22FF Q10%, 25V X7R ceramic
capacitors (0603)
Murata GRM188R71E224K
TDK C1608X7R1E224K
C5, C10
470pF Q10% 50V X7R ceramic
capacitor (0603)
Murata GRM188R71H471K
TDK C1608X7R1H471K
_______________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX17122 Evaluation Kit
Component List (continued)
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
22FF Q20%, 25V X5R ceramic
capacitors (1210)
Murata GRM32ER61E226K
Murata GRM32ER61E226M
High-gain, +25V npn transistor
(DPAK)
Fairchild KSH200
On Semi MJD200
C18, C21, C22
3
1
1
2
1
N1
1
10FF Q10%, 16V X5R ceramic
capacitor (0805)
Murata GRM21BR61C106K
KEMET C0805C106K4PAC
High-gain, -25V pnp transistor
(DPAK)
Fairchild KSH210
On Semi MJD210
C19
P1
1
1
-30V, 0.056Ip-channel MOSFET
(6 SC70 PowerPAK)
Vishay SiA421DJ
330pF Q10%, 50V X7R ceramic
capacitor (0603)
Murata GRM188R71H331K
TDK C1608X7R1H331K
Q1
C20
R1
R2
1
1
1
1
1
2
2
365kI Q1% resistor (0603)
33.2kI Q1% resistor (0603)
39.2kI Q1% resistor (0603)
324kI Q1% resistor (0603)
182kI Q1% resistor (0603)
22.1kI Q1% resistors (0603)
47.5kI Q1% resistors (0603)
12pF Q5%, 50V C0G ceramic
capacitors (0603)
Murata GRM1885C1H120J
TDK C1608C0G1H120J
R3
C26, C27
C28
R4
R5
R6, R13
R7, R22
15pF Q5%, 50V C0G ceramic
capacitor (0402)
Murata GRM1555C1H150J
TDK C1005C0G1H150J
10kI Q1% NTC resistor (0402)
Murata NCP15XH103F03RC
R8
1
Not installed, through-hole
OSCON capacitor
(OSCON-B)
R9
R10, R16
R11
1
2
1
1
1
2
2
8.25kI Q1% resistor (0603)
510I Q5% resistors (0603)
226kI Q1% resistor (0603)
10.5kI Q1% resistor (0603)
82.5kI Q1% resistor (0603)
10kI Q1% resistors (0603)
100kI Q5% resistors (0603)
C36
D1, D2
D3
0
2
1
30V, 3A Schottky diodes (M flat)
Toshiba CMS02
R12
R14
50V, 1A Schottky diode (SMA)
Fairchild SS15
Diodes, Inc. B150
R15, R20
R17, R18
Not installed, resistors (0603)
R19 is PC short; R21 and R24
are open
Small-signal diode (SOT23)
Fairchild BAT54S
Diodes, Inc. BAT54S
R19, R21, R24
0
1
1
D4
1
R23
U1
7.5kI Q1% resistor (0603)
GATE, SS, TP1,
TP2
TFT LCD power supply
(40 TQFN-EP*)
Maxim MAX17122ETL+
4
4
Test points
JU1–JU4
2-pin headers
—
4
1
Shunts
4.7FH, 3.5A inductors
TOKO FDV0620-4R7M
Sumida CDRH6D26HPNP-4R7P
NEC TOKIN MPLC0730L4R7
PCB: MAX17122 EVALUATION
KIT+
L1, L2
2
1
—
*EP = Exposed pad.
22FH, 1.6A inductor
Sumida CDRH8D28NP-220N
L3
2
______________________________________________________________________________________
MAX17122 Evaluation Kit
Component Suppliers
SUPPLIER
PHONE
WEBSITE
www.diodes.com
Diodes, Inc.
805-446-4800
888-522-5372
864-963-6300
770-436-1300
408-324-1790
602-244-6600
847-545-6700
800-348-2496
847-803-6100
847-297-0070
949-623-2900
402-563-6866
Fairchild Semiconductor
KEMET Corp.
www.fairchildsemi.com
www.kemet.com
Murata Electronics North America, Inc.
NEC TOKIN America, Inc.
ON Semiconductor
Sumida Corp.
www.murata-northamerica.com
www.nec-tokinamerica.com
www.onsemi.com
www.sumida.com
Taiyo Yuden
www.t-yuden.com
TDK Corp.
www.component.tdk.com
www.tokoam.com
TOKO America, Inc.
Toshiba America Electronic Components, Inc.
Vishay
www.toshiba.com/taec
www.vishay.com
Note: Indicate that you are using the MAX17122 when contacting these component suppliers.
7) Verify that the buck-boost regulator (VGOFF2) is
Quick Start
approximately -12V.
Recommended Equipment
U 10V to 14V, 5A DC power supply
8) Verify that the positive charge-pump linear-regulator
supply (VGON) is approximately +28V.
U Voltmeter
9) Verify that the negative charge-pump supply
(VGOFF1) is approximately -7.5V.
Procedure
The MAX17122 EV kit is fully assembled and test-
ed. Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
Detailed Description of Hardware
Jumper Settings
Several jumper settings in the following tables illustrate
features of the MAX17122 EV kit.
1) Verify that shunts are not installed across jumpers
JU1, JU2, and JU3.
Enable Inputs (EN1, EN2)
The MAX17122’s enable inputs can be configured
through jumpers JU1 and JU2. JU1 controls the EN1
pin, which enables the step-down regulator and gates
the EN2 function as well. JU2 controls pin EN2, which
enables the step-up and positive charge-pump linear
regulator when EN1 is high. When EN1 is low, all power
outputs are disabled. When EN_ is high, the respective
outputs are enabled. When EN_ is low, the respective
outputs are disabled. See Table 1 for jumpers JU1 and
JU2 configurations.
2) Verify that a shunt is installed across jumper JU4.
3) Connect the positive terminal of the power supply
to the VIN pad. Connect the negative terminal of the
power supply to the PGND pads closest to VIN.
4) Set the power supply VIN to +12V.
5) Turn on the power supply and verify that the step-up
switching regulator output (AVDD) is +15V.
6) Verify that the step-down switching regulator (3.3V) is
+3.3V.
Table 1. Jumpers JU1 and JU2 Functions (EN1, EN2)
SHUNT POSITION
EN1 PIN
EN2 PIN
OUTPUTS
JU1
Installed
JU2
Installed
Connected to GND
Connected to GND
Internally pulled high
Internally pulled high
Connected to GND
Internally pulled high
Connected to GND
Internally pulled high
All disabled
All disabled
Installed
Not installed
Installed
Not installed
Not installed*
*Default position.
Step-down enabled
All enabled
Not installed*
_______________________________________________________________________________________
3
MAX17122 Evaluation Kit
High-Voltage Stress Mode Input (JU3)
The MAX17122’s high-voltage stress (HVS) mode is
controlled through jumper JU3. When jumper JU3 is
installed, HVS is connected to VL and the RHVS output
is connected to AGND. When jumper JU3 is not installed,
the HVS pin is left unconnected and the RHVS output is
unconnected. See Table 2 for jumper JU3 configuration.
Step-Down Regulator Output-Voltage
Selection (+3.3V)
The EV kit’s step-down switching regulator supports both
fixed and adjustable output voltages. By default, the EV
kit’s step-down regulator’s output (3.3V) is set to the
+3.3V fixed mode by connecting FB2 to GND through
resistor R20. For adjustable mode (+1.5V to +3.6V),
select R21 and R20 to set the desired step-down regu-
lator output voltage. Refer to the Detailed Description,
Step-Down Regulator section in the MAX17122 IC data
sheet for instructions on selecting resistors R20 and R21.
Thermistor Network Connection (JU4)
The 100FA current from the SET pin, together with
resistor R23 at SET determines the cold-temperature
output voltage. The network at the NTC pin controls the
transition between the warm-temperature output volt-
age (determined by FB3 resistors R5 and R6) and the
cold-temperature output voltage. As configured, the
warm-temperature output voltage is -12V, slowly transi-
tioning at approximately +25NC to the cold-temperature
Buck-Boost Regulator Output-Voltage
Selection (VGOFF2)
The output voltage of the step-up regulator is tempera-
ture compensated. From the warm-temperature range
((3.3V - V
) > 1.65V), the output voltage is set by
NTC
output voltage level of -20V. Refer to the MAX17122 IC
data sheet for more information regarding temperature
compensation.
connecting a resistive voltage-divider from the output
(V ) to the +3.3V reference, with the center tap
connected to FB3. Select R6 in the 10kIto 50kIrange.
GOFF2
Jumper JU4 controls the thermistor network connected
to the NTC pin. When JU4 is installed, thermistor R8
is connected to NTC and the behavior of the GOFF2
output voltage varies with temperature. When JU4 is not
installed, NTC is connected to AGND through resistors
R7 and R9 and GOFF2 output voltage is fixed. See Table
3 for jumper JU4 configuration.
Calculate R5 with the following equation:
V
− V
FB3
− 3.3V
GOFF2_WARM
R5 = R6 ×
V
FB3
where V
, the step-up regulator’s feedback set point,
FB3
is +1.65V. Place R5 and R6 close to the IC.
For cold temperatures ((3.3V - V ) < V
NTC
voltage is set by:
), output
SET
Step-Up Regulator Output-Voltage
Selection (AVDD)
The EV kit’s step-up switching-regulator output (AVDD)
is set to +15V by feedback resistors R1 and R2. To gen-
erate output voltages other than +15V, select different
external voltage-divider resistors (R1 and R2). Refer to
the Step-Up Regulator, Output Voltage Selection section
in the MAX17122 IC data sheet for more information.
R6× V
+ R5× 3.3V
GOFF2_COLD
V
=
SET
R5 + R6
If the calculated V
voltage is larger than +1.65V,
SET
then temperature compensation is disabled and the
buck-boost regulator output will be V
temperatures.
at all
GOFF2_WARM
Calculate the SET pin resister R
(R23) as follows:
SET
V
SET
R
=
SET
100µA
Table 2. Jumper JU3 Function (HVS)
Table 3. Jumper JU4 Function (NTC)
SHUNT
POSITION
SHUNT
POSITION
THERMISTOR
NETWORK
HVS PIN
RHVS OUTPUT
GOFF2 OUTPUT
Connected to
AGND
Varies over
temperature
Installed
Connected to VL
Installed*
Connected
Not installed
Not connected
Fixed output
Not
installed*
Internally pulled to
GND
Unconnected
*Default position.
*Default position.
4
______________________________________________________________________________________
MAX17122 Evaluation Kit
Negative Linear Regulator Output-Voltage
Selection (VGOFF1)
Positive Charge-Pump Output-Voltage
Selection (VGON)
The positive charge-pump output (VGON) is set to +28V
by voltage-divider resistors R11 and R12. To set VGON
to other voltages, adjust the charge-pump regulator’s
output voltage by connecting a resistive voltage-divider
from the VGON output to AGND, with the center tap con-
nected to FBP. Select the lower resistor of the divider
R12 in the range of 10kI to 30kI. Calculate the upper
resistor R11 with the following equation:
The negative linear-regulator output (VGOFF1) is set to
-7.5V by voltage-divider resistors R13 and R14. To set
VGOFF1 to other voltages, adjust the negative linear-
regulator output voltage (VGOFF1) by connecting a
resistive voltage-divider from VGOFF1 to +3.3V with the
center tap connected to FBN. Select R13 in the 20kI to
50kI range. Calculate R14 with the following equation:
V
− V
FBN
− 3.3V
GOFF1
R14 = R13×
V
FBN
V
V
GON
R11= R12 ×
−1
where V
= +1V. Refer to the Negative Linear
FBN
FBP
Regulator, Output-Voltage Selection section in the
MAX17122 IC data sheet for instructions on selecting
R13 and R14.
where V
= +1.25V (typ). Refer to the Positive Charge-
FBP
Pump Linear Regulator section in the MAX17122 IC data
sheet for instructions on selecting R11 and R12.
_______________________________________________________________________________________
5
MAX17122 Evaluation Kit
Figure 1. MAX17122 EV Kit Schematic
6
______________________________________________________________________________________
MAX17122 Evaluation Kit
1.0”
1.0”
Figure 2. MAX17122 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX17122 EV Kit PCB Layout—Component Side
1.0”
Figure 4. MAX17122 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
7
©
2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明