MAX17320G10 [MAXIM]
2S-4S ModelGauge m5 EZ Fuel Gauge with Protector, Internal Self-Discharge Detection, and SHA-256 Authentication;型号: | MAX17320G10 |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | 2S-4S ModelGauge m5 EZ Fuel Gauge with Protector, Internal Self-Discharge Detection, and SHA-256 Authentication 仪表 |
文件: | 总179页 (文件大小:4192K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EVALUATION KIT AVAILABLE
Click here to ask about the production status of specific part numbers.
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection,
and SHA-256 Authentication
General Description
Benefits and Features
The MAX17320 is a 38μA I stand-alone pack-side fuel
● Battery Health + Programmable Safety/Protection
• Overvoltage (Temperature Dependent)
• Overcharge/Overdischarge/Short-Circuit Current
• Over/Undertemperature
Q
gauge IC with protector, battery internal self-discharge de-
tection, and optional SHA-256 authentication for 2 to 4 se-
ries lithium-ion/polymer batteries.
• Undervoltage + SmartEmpty
The IC monitors the voltage, current, temperature and
state of the battery to provide protection against over/un-
dervoltage, overcurrent, short-circuit, over/undertempera-
ture, overcharge, and internal self-discharge conditions
using external high-side N-FETs, and provides charging
prescription to ensure that the battery operates under safe
conditions, thereby prolonging the life of the battery. The
IC balances the cells using internal FETs. During prequal
charging, the IC uses the CHGFET to linearly control
charging.
• Battery Internal Self-Discharge Detection
• Ideal Diode Discharge During Charge Fault
• Charging Prescriptions (JEITA)
• Prequal Charge Control with CHG FET
● ModelGauge m5 EZ Algorithm
• Percent, Capacity, Time-to-Empty/Full, Age
• Cycle+™ Age Forecast
● Precision Measurement Without Calibration
• Current, Voltage, Power, Time, Cycles
• Die Temperature, 4 Thermistors ±1˚C
To prevent battery pack cloning, the IC integrates
SHA-256 authentication with a 160-bit secret key. Each IC
incorporates a unique 64-bit ID.
● Cell Balancing with Internal FETs
● SHA-256 Authentication
● Nonvolatile Memory for Stand-Alone Operation
• History Logging, User Data (84 Bytes)
TM
The fuel gauge uses Maxim ModelGauge
m5 algorithm
that combines the short-term accuracy and linearity of a
coulomb counter with the long-term stability of a voltage-
based fuel gauge to provide industry-leading fuel gauge
accuracy. The IC automatically compensates for cell ag-
ing, temperature, and discharge rate, and provides accu-
rate state-of-charge (SOC) in milliampere-hours (mAh) or
percentage (%) over a wide range of operating conditions.
● Low Quiescent Current
• FETs Enabled: 38μA Active
● Pushbutton Wakeup—Eliminates System
Consumption Until Button Press
● Always-On LDO
● Dynamic Power—Estimates Power Capability
● SBS 1.1 Compatible Register Set
The IC provides a configurable always-on LDO that can
power small critical loads on the system side without over-
loading the cells even under fault conditions. Dynamic
power functionality provides the instantaneous maximum
battery output power which can be delivered to the system
without violating the minimum system input voltage.
Ordering Information appears at end of data sheet.
Simplified Block Diagram
3 TERM
FUSE*
PACK+
®
2
A Maxim 1-Wire or 2-wire I C/SMBus interface provides
access to data and control registers. The IC is available in
a lead-free, 2.4mm x 2.6mm 30-bump 0.4mm pitch WLP
and 4mm x 4mm 24-pin TQFN packages.
N
PFAIL* CHG
CP
DIS
ZVC
PCKP
IN
AOLDO*
REG3
REG2
BATTS
CELL3*
CELL2*
ALRT*
Applications
SDA/DQ
SCL/OD
TH4*
● Smartphones, Tablets, and 2-in-1 Laptops
● Medical Devices, Health and Fitness Monitors
● Digital Still, Video, and Action Cameras
● Handheld Computers, Radios, and Terminals
● Power Tools, Wireless Speakers, and Drones
● Smart Batteries and Battery Backup
TH3*
CELL1
TH2*
MAX17320
GND
CSP
TH1*
CSN
PACK-
*OPTIONAL
ModelGauge is a trademark of Maxim Integrated Products, Inc.
1-Wire is a registered trademark of Maxim Integrated Products, Inc.
Cycle+ is a trademark of Maxim Integrated Products, Inc.
19-100749; Rev 7; 8/20
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS
General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Benefits and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Simplified Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
30 WLP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
24 TQFN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Typical Operating Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
WLP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
TQFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Functional Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Protector Thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Voltage Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
SmartEmpty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Current Thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Fast Overcurrent Comparators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Overcurrent Comparator Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Slow Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Temperature Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Additional Protection Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Battery Internal Self-Discharge Detection (ISD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Charger Presence and Ideal Diode Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Permanent Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Charge Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Zero-Volt Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Prequal Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Charging Prescription . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Step Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
2
Disabling FETs by Pin-Control or I C Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
www.maximintegrated.com
Maxim Integrated | 2
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
Fuel Gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ModelGauge m5 Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ModelGauge m5 EZ Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
OCV Estimation and Coulomb Count Mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Empty Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
End-of-Charge Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Fuel Gauge Learning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Converge-To-Empty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Determining Fuel-Gauge Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Initial Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cycle+ Age Forecasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
nAgeFcCfg Register (1E2h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
AgeForecast Register (0B9h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Age Forecasting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Enabling Age Forecasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Battery Life Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Life Logging Data Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Determining Number of Valid Logging Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Reading History Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
History Data Reading Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Analog Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Cell Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cell Balancing Window of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cell Balancing Order and Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
RMismatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Cell Balancing Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Cell Balancing Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Cell Balancing Duty Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Internal Self-Discharge Detection Interaction with Cell Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Backup and Always-On LDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
SHA-256 Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Wake-Up/Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Modes of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Power Mode Transition State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Pushbutton Wake-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Register Description Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Standard Register Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
www.maximintegrated.com
Maxim Integrated | 3
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
Device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Nonvolatile Backup and Initial Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Register Naming Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Protection Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
nPackCfg Register (1B5h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Voltage Protection Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
nUVPrtTh Register (1D0h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
nJEITAV Register (1D9h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
nOVPrtTh Register (1DAh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
nBalTh Register (1D4h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Current Protection Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
nODSCTh Register (1DDh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
nODSCCfg Register (1DEh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
nIPrtTh1 Register (1D3h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
nJEITAC Register (1D8h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Temperature Protection Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
nTPrtTh1 Register (1D1h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
nTPrtTh2 Register (1D5h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
nTPrtTh3 Register (1D2h) (beyond JEITA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
nProtMiscTh Register (1D6h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Fault Timer Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
nDelayCfg Register (1DCh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Battery Internal Self-Discharge Detection Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Status/Configuration Protection Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
nProtCfg Register (1D7h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Status Register (000h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Status2 Register (0B0h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
nBattStatus Register (1A8h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
nFaultLog Register (1AEh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
ProtStatus Register (0D9h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
ProtAlrt Register (0AFh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
HProtCfg2 Register (1F1h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Nonvolatile Memory Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Analog Measurement Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Voltage Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
VCell Register (01Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
AvgVCell Register (019h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Cell1-Cell4 Registers (0D8h-0D5h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
www.maximintegrated.com
Maxim Integrated | 4
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
AvgCell1-AvgCell4 Registers (0D4h-0D1h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Batt Register (0DAh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
PCKP Register (0DBh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
MaxMinVolt Register (0008h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Current Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Current Measurement Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Current Register (01Ch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
AvgCurrent Register (01Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
MaxMinCurr Register (00Ah). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
nCGain Register (1C8h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
CGTempCo (0B8h)/nCGTempCo (1C9h) Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
nRSense Register (1CFh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Copper Trace Current Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Temperature Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Temperature Measurement Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Temp Register (01Bh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
AvgTA Register (016h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
MaxMinTemp Register (009h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
nThermCfg Register (1CAh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DieTemp Register (034h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
AvgDieTemp Register (040h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Temp1/2/3/4 Registers (13Ah-137h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
AvgTemp1/2/3/4 Registers (136h-133h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Charge Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
ChargingCurrent Register (028h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
ChargingVoltage Register (02Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
nStepChg Register (1DBh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
nChgCfg (1C2h) Prequal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
ModelGauge m5 Algorithm Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
ModelGauge m5 Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
ModelGauge m5 Algorithm Output Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
RepCap Register (005h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
RepSOC Register (006h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
FullCapRep Register (010h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
TTE Register (011h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
TTF Register (020h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Age Register (007h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
www.maximintegrated.com
Maxim Integrated | 5
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
Cycles Register (017h) and nCycles (1A4h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Timer Register (03Eh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
TimerH Register (0BEh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
FullCap Register (010h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
nFullCapNom Register (1A5h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
RCell Register (014h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
VRipple Register (0B2h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
nVoltTemp Register (1AAh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
ModelGauge m5 Algorithm Input Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
nXTable0 (180h) to nXTable11 (18Bh) Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
nOCVTable0 (190h) to nOCVTable11 (19Bh) Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
nQRTable00 (1A0h) to nQRTable30 (1A3h) Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
nFullSOCThr Register (1C6h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
nVEmpty Register (19Eh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
nDesignCap Register(1B3h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
nIChgTerm Register (19Ch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
nRComp0 Register (1A6h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
nTempCo Register (1A7h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
ModelGauge m5 Algorithm Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
nConfig Register (1B0h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
nNVCfg0 Register (1B8h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
nNVCfg1 Register (1B9h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
nNVCfg2 Register (1BAh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
nHibCfg Register (1BBh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
nFilterCfg Register (19Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
nMiscCfg Register (1B2h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
nRelaxCfg Register (1B6h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
nLearnCfg Register (19Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
nTTFCfg Register (1C7h)/CVMixCap (0B6h) and CVHalfTime (0B7h) Registers . . . . . . . . . . . . . . . . . . 114
nConvgCfg Register (1B7h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
nRippleCfg Register (1B1h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
SOCHold Register (0D0h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
ModelGauge m5 Algorithm Additional Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
QResidual Register (00Ch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
VFSOC Register (0FFh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
VFOCV Register (0FBh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
QH Register (4Dh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
AvCap Register (01Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
www.maximintegrated.com
Maxim Integrated | 6
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
AvSOC Register (00Eh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
MixSOC Register (00Dh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
MixCap Register (02Bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
VFRemCap Register (04Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
FStat Register (03Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Identification Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
DevName Register (021h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
nROMID0 (1BCh)/nROMID1 (1BDh)/nROMID2 (1BEh)/nROMID3 (1BFh) Registers . . . . . . . . . . . . . . . . . . 119
AtRate Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
AtRate Register (004h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
AtQResidual Register (0DCh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
AtTTE Register (0DDh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
AtAvSOC Register (0CEh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
AtAvCap Register (0DFh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Alert Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
nVAlrtTh Register (18Ch). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
nTAlrtTh Register (18Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
nSAlrtTh Register (18Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
nIAlrtTh Register (0ACh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
ModelGauge m5 Memory Space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Nonvolatile Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Nonvolatile Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Shadow RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Shadow RAM and Nonvolatile Memory Relationship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Nonvolatile Memory Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
COPY NV BLOCK [E904h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
NV RECALL [E001h]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
HISTORY RECALL [E2XXh] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Nonvolatile Block Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Determining Number of Remaining Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Enabling and Freeing Nonvolatile vs. Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
100 Record Life Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Memory Locks and Write Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
CommStat Register (061h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
NV LOCK [6AXXh] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Locking Memory Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Reading Lock State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
www.maximintegrated.com
Maxim Integrated | 7
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
SHA-256 Authentication Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Authentication Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Procedure to Verify a Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Alternate Authentication Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Battery Authentication without a Host Side Secret. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Secret Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Single-Step Secret Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Single-Step Secret Generation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Multistep Secret Generation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Multistep Secret Generation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
2-Stage MKDF Authentication Scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Create a Unique Intermediate Secret. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Procedure for 2-Stage MKDF Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Determining Number of Remaining Updates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Authentication Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
COMPUTE MAC WITHOUT ROM ID [3600h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
COMPUTE MAC WITH ROM ID [3500h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
COMPUTE NEXT SECRET WITHOUT ROM ID [3000h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
COMPUTE NEXT SECRET WITH ROM ID [3300h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
CLEAR SECRET [5A00h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
LOCK SECRET [6000h]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
COPY INTERMEDIATE SECRET FROM NVM [3800] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
COMPUTE NEXT INTERMEDIATE SECRET WITH ROMID [3900] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
COMPUTE NEXT INTERMEDIATE SECRET WITHOUT ROMID [3A00] . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
COMPUTE MAC FROM INTERMEDIATE SECRET WITHOUT ROMID [3C00]. . . . . . . . . . . . . . . . . . . . . . 149
COMPUTE MAC FROM INTERMEDIATE SECRET WITH ROMID [3D00]. . . . . . . . . . . . . . . . . . . . . . . . . . 149
Smart Battery Compliant Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
SBS Compliant Memory Space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
sManfctAccess Register (100h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
sRemCapAlarm/sRemTimeAlarm Registers (101h/102h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
sBatteryMode Register (103h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
At-Rate Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
sAtRate Register (104h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
sAtTTF Register (105h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
sAtTTE Register (106h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
sAtRateOK Register (107h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
sTemperature Register (108h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
sPackVoltage Register (109h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
www.maximintegrated.com
Maxim Integrated | 8
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
sChargingCurrent Register (114h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
sBatteryStatus Register (116h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
sSpecInfo Register (11Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
sManfctrDate Register (11Bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
sSerialNumber Register (11Ch to 11Eh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
sManfctrName Register (120h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
sDeviceName Register (121h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
sDevChemistry Register (122h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sManfctData Registers (123h to 12Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sDesignVolt Register (119h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sFirstUsed Register (136h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sCell1-4 Registers (13Fh-13Ch). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sAvgCell1-4 Registers (14Fh-14Ch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sAvCap Register (167h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sMixCap Register (168h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
sManfctInfo Register (170h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
nDesignVoltage Register (1E3h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
nSBSCfg Register (1B4h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Nonvolatile SBS Register Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
nCGain and Sense Resistor Relationship. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Device Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Reset Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
HARDWARE RESET [000Fh to address 060h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
FUEL GAUGE RESET [8000h to address 0ABh]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
2-Wire Bus System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
2-Wire Bus Interface Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
I/O Signaling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Bit Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Bus Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
START and STOP Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Acknowledge Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Data Order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Slave Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Read/Write Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
2-Wire Bus Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
www.maximintegrated.com
Maxim Integrated | 9
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
2
I C Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
2
I C Write Data Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
2
I C Read Data Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
SBS Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
SBS Write Word Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Example SBS Write Word Communication Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
SBS Read Word Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Example SBS Read Word Communication Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
SBS Write Block Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
SBS Read Block Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Example SBS Read Block Communication Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Valid SBS Read Block Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Packet Error Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
PEC CRC Generation Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
1-Wire Bus System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
1-Wire Bus Interface Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
64-Bit Net Address (ROM ID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
I/O Signaling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Reset Time Slot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
1-Wire Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Write Time Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Read Time Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
1-Wire Write and Read Time Slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Transaction Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Net Address Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Read Net Address [33h] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Match Net Address [55h]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Skip Net Address [CCh] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Search Net Address [F0h]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
1-Wire Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Read Data [69h, LL, HH]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Write Data [6Ch, LL, HH]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Example 1-Wire Communication Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Summary of Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
16-Reading ADC FIFO Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Appendix A: Reading History Data Pseudo-Code Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Typical Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
www.maximintegrated.com
Maxim Integrated | 10
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TABLE OF CONTENTS (CONTINUED)
Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Typical 2S-4S Battery Pack and System Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Typical Application with a Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Pushbutton Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
www.maximintegrated.com
Maxim Integrated | 11
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LIST OF FIGURES
Figure 1. Simplified Protector State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 2. Programmable Voltage Thresholds (Default Values Shown) (All Voltages are per Cell). . . . . . . . . . . . . . . . . 40
Figure 3. Programmable Current Thresholds (Default Values Shown With 5mΩ Sense Resistor). . . . . . . . . . . . . . . . . 41
Figure 4. Standard Undervoltage Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 5. SmartEmpty Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 6. Fast, Medium, and Slow Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 7. Overcurrent Comparator Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 8. Example of Internal Self-Discharge with Temperature Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 9. Zero-Volt Charge Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 10. Step-Charging State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 11. Merger of Coulomb Counter and Voltage-Based Fuel Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 12. ModelGauge m5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 13. ModelGauge m5 Typical Accuracy Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 14. Handling Changes in Empty Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 15. False End-of-Charge Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 16. FullCapRep Learning at End-of-Charge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 17. FullCapNom Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 18. Converge-to-Empty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 19. Benefits of Age Forecasting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 20. Sample Life Logging Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure 21. Write Flag Register and Valid Flag Register Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 22. Cell Balancing Window of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 23. Cell Balancing Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 24. Cell Balancing Duty Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 25. Power Modes Transition State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 26. ModelGauge m5 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Figure 27. Cell Relaxation Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 28. TTF Configuration Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Figure 29. Shadow RAM and Nonvolatile Memory Relationship. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Figure 30. Procedure to Verify a Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 31. Battery Authentication without a Host Side Secret. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Figure 32. Single-Step Secret Generation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Figure 33. Multistep Secret Generation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Figure 34. Create a Unique Intermediate Secret. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Figure 35. Procedure for 2-Stage MKDF Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Figure 36. 2-Wire Bus Interface Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Figure 37. 2-Wire Bus Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
2
Figure 38. Example I C Write Data Communication Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
www.maximintegrated.com
Maxim Integrated | 12
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LIST OF FIGURES (CONTINUED)
2
Figure 39. Example I C Read Data Communication Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Figure 40. Example SBS Write Word Communication Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 41. Example SBS Read Word Communication Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 42. Example SBS Read Block Communication Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 43. PEC CRC Generation Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Figure 44. 1-Wire Bus Interface Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Figure 45. 1-Wire Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Figure 46. 1-Wire Write and Read Time Slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Figure 47. Example 1-Wire Communication Sequences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
www.maximintegrated.com
Maxim Integrated | 13
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LIST OF TABLES
Table 1. Summary of Protector Registers by Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 2. Voltage Thresholds (All Voltages are per Cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 3. Current Threshold Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 4. Additional Protection Thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 5. AvgCurrDet Threshold When Using 5mΩ and Default nProtMiscTh.CurrDet = 15mA . . . . . . . . . . . . . . . . . . . 49
Table 6. nAgeFcCfg Register (1E2h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 7. Minimum and Maximum Cell Sizes for Age Forecasting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 8. Life Logging Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 9. Reading History Page Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Table 10. Decoding History Page Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Table 11. Reading History Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 12. Analog Measurement Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 13. Cell Balancing Thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Table 14. Modes of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Table 15. ModelGauge Register Standard Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Table 16. nPackCfg (1B5h) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Table 17. nUVPrtTh Register (1D0h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Table 18. nJEITAV Register (1D9h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Table 19. nOVPrtTh Register (1DAh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 20. nBalTh Register (1D4h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 21. nODSCTh Register (1DDh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 22. OCTH, SCTh, and ODTH Sample Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 23. nODSCCfg Register (1DEh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 24. nIPrtTh1 Register (1D3h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 25. nJEITAC Register (1D8h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 26. nTPrtTh1 Register (1D1h) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 27. nTPrtTh2 (1D5h) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 28. nTPrtTh3 Register (1D2h) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Table 29. nProtMiscTh Register (1D6h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Table 30. nDelayCfg (1DCh) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 31. UVPTimer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 32. TempTimer/TempTrans Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 33. PermFailTimer Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 34. OverCurrTimer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 35. OVPTimer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 36. FullTimer/Prequal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 37. ChgWDT Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 38. nProtCfg2 Register (1DFh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
www.maximintegrated.com
Maxim Integrated | 14
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LIST OF TABLES (CONTINUED)
Table 39. nTCurve Register (0x1C9) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 40. Alert and Fault Mode Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 41. LeakCurrRep Register (0x16F) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 42. nProtCfg Register (1D7h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Table 43. Status Register (000h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Table 44. Status2 Register (0B0h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Table 45. nBattStatus Register (1A8h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Table 46. nFaultLog Register (1AEh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Table 47. ProtStatus Register (0D9h) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Table 48. ProtAlrt Register (0AFh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table 49. HProtCfg2 Register (1F1h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table 50. MaxMinVolt (008h)/nMaxMinVolt (1ACh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Table 51. Current Measurement Range and Resolution vs. Sense Resistor Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table 52. MaxMinCurr (00Ah)/nMaxMinCurr (1ABh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table 53. nCGain Register (1C8h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Table 54. Copper Trace Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Table 55. MaxMinTemp (009h)/nMaxMinTemp (1ADh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table 56. Register Settings for Common Thermistor Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Table 57. nStepChg Register (1DBh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Table 58. nChgCfg Register (1C2h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Table 59. Cycles Register (017h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table 60. nCycles Register (1A4h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table 61. nNVCfg2.FibScl Setting Determines LSb of nNVCfg2.CyclesCount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table 62. nVoltTemp Register (1AAh) Format when nNVCfg2.enVT = 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Table 63. nFullSOCThr (1C6h)/FullSOCThr (013h) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Table 64. VEmpty (03Ah)/nVEmpty (19Eh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Table 65. nConfig Register (1B0h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Table 66. Config Register (00Bh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Table 67. Config2 Register (0ABh) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Table 68. nNVCfg0 Register (1B8h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Table 69. nNVCfg1 Register (1B9h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Table 70. nNVCfg2 Register (1BAh) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Table 71. nHibCfg Register (1BBh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Table 72. FilterCfg (029h)/nFilterCfg (19Dh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Table 73. MiscCfg (00Fh)/nMiscCfg (1B2h) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Table 74. RelaxCfg (0A0h)/nRelaxCfg (1B6h) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Table 75. LearnCfg (0A1h)/nLearnCfg (19Fh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Table 76. nTTFCfg Register (1C7h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
www.maximintegrated.com
Maxim Integrated | 15
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LIST OF TABLES (CONTINUED)
Table 77. nConvgCfg Register (1B7h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Table 78. nRippleCfg Register (1B1h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Table 79. SOCHold (0D0h) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Table 80. FStat Register (03Dh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Table 81. DevName Register (021h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Table 82. nROMID Registers (1BCh to 1BFh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Table 83. VAlrtTh (001h)/nVAlrtTh (18Ch) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Table 84. TAlrtTh (002h)/nTAlrtTh (18Dh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Table 85. SAlrtTh (003h)/nSAlrtTh (18Fh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Table 86. IAlrtTh (0ACh)/nIAlrtTh (18Eh) Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Table 87. Top Level Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Table 88. Individual Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Table 89. ModelGauge m5 Register Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Table 90. Nonvolatile Register Memory Map (slave address 16h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Table 91. History Recall Command Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Table 92. Number of Remaining Config Memory Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Table 93. Total Bytes Freeable for User Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Table 94. Making Nonvolatile Memory Available for User Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Table 95. Nonvolatile Memory Configuration Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Table 96. Fibonacci Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Table 97. Longest Update Interval (in battery cycles). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Table 98. Saving Schedule Example With the Most Preferred Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Table 99. CommStat Register (061h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Table 100. Format of LOCK Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Table 101. Format of Lock Register (07Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Table 102. Number of Remaining Secret Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Table 103. SBS Register Space Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Table 104. sManfctAccess Register (100h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Table 105. Protection Mode Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Table 106. sBatteryMode Register (103h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Table 107. BatteryStatus Register (116h) Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Table 108. SpecInfo Register (11Ah) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Table 109. sManfctrDate Register (11Bh) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Table 110. nDesignVoltage Register (1E3h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Table 111. nSBSCfg Register (1B4h) Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Table 112. SBS to Nonvolatile Memory Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Table 113. nCGain Register Settings to Meet SBS Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Table 114. 2-Wire Slave Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
www.maximintegrated.com
Maxim Integrated | 16
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LIST OF TABLES (CONTINUED)
Table 115. Valid SBS Read Block Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Table 116. 1-Wire Net Address Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Table 117. All Function Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
2
Table 118. I C Slave Address = 0x16 (SBS Memory Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
www.maximintegrated.com
Maxim Integrated | 17
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Absolute Maximum Ratings
IN to GND............................................................... -0.3V to +20V
BATTS to GND..................... -0.3V to min of (IN + 0.3 and +20)V
CELL3, CELL2, CELL1 to GND ...... -0.3V to min of (IN + 0.3 and
BATTS + 0.3)V
BATTS to CELL3 (Balancing switches).................. -0.3V to +20V
CELL3 to CELL2 (Balancing switches) .................. -0.3V to +20V
CELL2 to CELL1 (Balancing switches) .................. -0.3V to +20V
CELL1 to GND (Balancing switches) ..................... -0.3V to +20V
CP to GND.............................................................. -0.3V to +36V
CP to IN.................................................................. -0.3V to +36V
CHG to GND.................................................. IN - 0.3 to CP + 0.3
DIS to GND......................................... PCKP - 0.3V to CP + 0.3V
PCKP, ZVC to GND................................................ -0.3V to +28V
SCL, SDA, ALRT to GND .......................................-0.3V to +20V
REG3, AOLDO to GND.............................................-0.3V to +6V
PFAIL, TH1, TH2, TH3, TH4 to GND..........-0.3V to REG3 +0.3V
REG2 to GND ........................................................-0.3V to +2.2V
CSN to GND ................................................................-2V to +2V
CSP to GND...........................................................-0.3V to +0.3V
Continuous Current of Balancing Switches........................100mA
Continuous Current between ZVC and IN ...........................50mA
Continuous Power Dissipation (Single-Layer Board) (T = +70°C,
A
derate 65mW/°C above +70°C) ......................................1000mW
Continuous Power Dissipation (Multilayer Board) (T = +70°C,
A
derate 55mW/°C above +70°C) ......................................1950mW
Operating Temperature Range.............................-40°C to +85°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the
device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
www.maximintegrated.com
Maxim Integrated | 18
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Package Information
30 WLP
Package Code
W302O2+1
Outline Number
21-100381
Land Pattern Number
Thermal Resistance, Four-Layer Board:
Refer to Application Note 1891
Junction to Ambient (θ
)
49°C/W
N/A
JA
Junction to Case (θ
)
JC
www.maximintegrated.com
Maxim Integrated | 19
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
24 TQFN
Package Code
T2444+4C
21-0139
90-0022
Outline Number
Land Pattern Number
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θ
)
68°C/W
11°C/W
JA
Junction to Case (θ
)
JC
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θ
)
60°C/W
11°C/W
JA
Junction to Case (θ
)
JC
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates
RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal
considerations, refer to www.maximintegrated.com/thermal-tutorial.
www.maximintegrated.com
Maxim Integrated | 20
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Electrical Characteristics
(IN = 4.2V to 18V, T = -40°C to +85°C, typical values are T = +25°C, see the schematic in the Functional Diagram. Limits are 100%
A
A
tested at T = +25°C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and
A
characterization.)
PARAMETER
POWER SUPPLY
Supply Voltage
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
V
IN
4.2
18
V
Shutdown Supply
Current
I
Shutdown, V
= 18V, +25°C
BATT
2.2
16
3.5
μA
DD0
Ship Mode Supply
Current
I
I
T
T
≤ +50°C
25
57
μA
μA
DD1
A
≤ +50°C, average current, not
A
Active Supply Current
including thermistor measurement
current, AOLDO off
38
DD2
REG3 Voltage
REG2 Voltage
V
V
3.4
1.8
1.8
3.4
V
V
REG3
REG2
1.8V output, I
3.4V output, I
= 2mA
= 2mA
1.62
3
1.98
3.8
LOAD
LOAD
Always-On LDO Voltage
V
V
V
AOLDO
CHARGE PUMP
1.5 x IN -
1
1.5 x IN
+ 1
1.5 x IN < CP
6V selection
, V - IN
REG CP
1.5 x IN
5
7
9
6
8
7
9
Charge Pump Output
V
CP
8V setting, V > 6V
IN
10V setting, V > 7.5V
IN
10
11
CHG DRIVER
CHG is high, IN = 10V, 10MΩ resistor
between CHG and IN
CHG Driver Output
V
CP - 0.1
CP
CP
CP + 0.1
V
CHGHIGH
R
CHG is high
CHG is low
4000
1000
CHGON
CHG Resistance
Ω
R
CHGOFF
DIS DRIVER
DIS is high, IN = 10V, 10MΩ resistor
between DIS and PCKP
DIS Driver Output
V
CP - 0.1
CP + 0.1
V
DISHIGH
R
DIS is high
DIS is low
4000
1000
DISON
DIS Resistance
Ω
R
DISOFF
ZERO-VOLT RECOVERY
10mA Recovery
current
1.4
2.1
2.5
2.4
2.9
3.4
3.3
3.8
4.5
30mA Recovery
current
ZVC Minimum Voltage
V
IN = 0
V
ZVCMIN
50mA Recovery
current
ANALOG-TO-DIGITAL CONVERSION
T
= +25°C (Note 10)
-12.5
-25
+12.5
+25
Cell Voltage
Measurement Error
A
V
GERR
mV
(Note 10)
www.maximintegrated.com
Maxim Integrated | 21
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Electrical Characteristics (continued)
(IN = 4.2V to 18V, T = -40°C to +85°C, typical values are T = +25°C, see the schematic in the Functional Diagram. Limits are 100%
A
A
tested at T = +25°C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and
A
characterization.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Cell Voltage Mismatch
Error
Cell voltage mismatch between channels
(CELL1, 2, 3, 4) +25°C
V
CMM
-5
+5
mV
T
20V
= +25°C, IN = BATTS, from 4.2V to
A
-30
+30
BATT Voltage
Measurement Error
VB
VP
mV
GERR
GERR
IN = BATTS, from 4.2V to 20V
-100
-30
+100
+30
T
A
= +25°C
PCKP Voltage
Measurement Error
mV
μV
-100
+100
Cell Voltage
Measurement
Resolution
V
Individual cell
BATTS
78.125
312.5
312.5
LSB
BATT Voltage
Measurement
Resolution
VB
VP
μV
μV
LSB
PCKP Voltage
Measurement
Resolution
PCKP pin
LSB
Cell Voltage
Measurement Range
V
(Note 10)
2.1
4.2
4.2
4.9
V
V
FS
BATT Voltage
Measurement Range
VB
VP
BATTS pin
19.6
19.6
FS
FS
PCKP Voltage
Measurement Range
PCKP pin
V
Current Measurement
Offset Error
I
CSP = 0V, long-term average (Note 2)
CSP between -50mV and +50mV
±2
μV
OERR
GERR
Current Measurement
Gain Error
% of
Reading
I
-1
+1
Current Measurement
Resolution
I
1.5625
±51.2
±1
μV
mV
ºC
LSB
Current Measurement
Range
I
FS
Die Temperature
Measurement Error
TI
GERR
Die Temperature
Measurement
Resolution
TI
(Note 11)
0.00391
±1
ºC
LSB
Thermistor
Measurement Error
% of
Reading
TE
See the Thermistor Configuration section
GERR
RESISTANCE AND LEAKAGE
Leakage Current,
CELL1, CELL2, CELL3,
BATTS, CSN, ALRT,
I
ALRT < 15V, IN < CP < 30V
-1
+1
μA
LEAK
PFAIL, ZVC, CHG, DIS
www.maximintegrated.com
Maxim Integrated | 22
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Electrical Characteristics (continued)
(IN = 4.2V to 18V, T = -40°C to +85°C, typical values are T = +25°C, see the schematic in the Functional Diagram. Limits are 100%
A
A
tested at T = +25°C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and
A
characterization.)
PARAMETER
SYMBOL
CONDITIONS
= 18V, I = 50mA, between
BATTS - CELL3, CELL3 - CELL2, CELL2
- CELL1, and CELL1 - CSP
MIN
TYP
MAX
UNITS
V
BATT
BAL
Cell-Balancing
Resistance
R
3
9
20
Ω
BAL
PD
Communication
Removal Test Current
I
SDA, SCL pin = 0.4V
0.05
0.2
0.4
0.4
μA
INPUT / OUTPUT
Output Drive Low,
ALRT, SDA/DQ, PFAIL
V
OL
I
I
= 4mA, REG3 = 3.4V
= -1mA
V
V
V
OL
Output Drive High,
PFAIL
REG3-0.
1
V
OH
OH
Input Logic High, SCL/
OD, SDA/DQ, ALRT
V
IH
1.5
Input Logic Low, SCL/
OD, SDA/DQ, ALRT
V
IL
0.44
V
ALRT Wake Debounce
Sleep mode
100
ms
COMPARATORS
Overcurrent Threshold
Offset Error
OC
OC
OC, OD, or SC comparator
OC, OD, or SC comparator
-1.2
-5.0
+1.2
+5.0
mV
OE
GE
Overcurrent Threshold
Gain Error
% of
Threshold
NONVOLATILE MEMORY
Programming Supply
Current
Current from V
programming
for block
BATT
I
4
10
7360
1280
5
mA
ms
PROG
Block Programming
Time
t
368
64
BLOCK
Page Programming
Time
SHA secret update or learned parameters
update
t
ms
UPDATE
Nonvolatile Memory
Recall Time
t
ms
RECALL
Write Capacity,
Configuration Memory
n
(Notes 2, 3, 4)
(Notes 2, 3, 4)
7
5
writes
writes
CONFIG
Write Capacity, SHA
Secret
n
SECRET
Write Capacity, Learned
Parameters
n
(Notes 2, 3, 4)
(Note 2)
99
writes
years
LEARNED
Data Retention
t
10
NV
1-WIRE INTERFACE, REGULAR SPEED
Time Slot
t
60
1
120
μs
μs
μs
μs
SLOT
Recovery Time
Write-0 Low Time
Write-1 Low Time
t
REC
t
t
60
1
120
15
LOW0
LOW1
www.maximintegrated.com
Maxim Integrated | 23
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Electrical Characteristics (continued)
(IN = 4.2V to 18V, T = -40°C to +85°C, typical values are T = +25°C, see the schematic in the Functional Diagram. Limits are 100%
A
A
tested at T = +25°C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and
A
characterization.)
PARAMETER
Read-Data Valid
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
μs
t
15
RDV
Reset-Time High
t
480
480
15
μs
RSTH
Reset-Time Low
t
960
60
μs
RSTL
Presence-Detect High
Presence-Detect Low
t
μs
PDH
t
60
240
μs
PDL
1-WIRE INTERFACE, OVERDRIVE SPEED
Time Slot
t
6
1
6
1
16
μs
μs
μs
μs
μs
μs
μs
μs
μs
SLOT
Recovery Time
t
REC
Write-0 Low Time
Write-1 Low Time
Read-Data Valid
Reset-Time High
Reset-Time Low
Presence-Detect High
Presence-Detect Low
t
t
16
2
LOW0
LOW1
t
2
RDV
t
48
48
2
RSTH
t
80
6
RSTL
t
PDH
t
8
24
PDL
2
2-WIRE INTERFACE (I C and SMBus)
SCL Clock Frequency
f
(Note 5)
(Note 6)
400
kHz
μs
SCL
Bus Free Time Between
a STOP and START
Condition
t
1.3
BUF
Hold Time (Repeated)
START Condition
t
0.6
1.3
0.6
μs
μs
μs
HD:STA
Low Period of SCL
Clock
t
LOW
High Period of SCL
Clock
t
HIGH
Setup Time for a
Repeated START
Condition
t
0.6
μs
SU:STA
Data Hold Time
Data Setup Time
t
(Notes 7, 8)
(Note 7)
0
0.9
μs
ns
HD:DAT
t
100
SU:DAT
Rise Time of Both SDA
and SCL Signals
t
5
5
300
300
ns
ns
μs
R
Fall Time of Both SDA
and SCL Signals
t
F
Setup Time for STOP
Condition
t
0.6
SU:STO
Spike Pulse Width
Suppressed by Input
Filter
t
(Note 9)
50
ns
SP
www.maximintegrated.com
Maxim Integrated | 24
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Electrical Characteristics (continued)
(IN = 4.2V to 18V, T = -40°C to +85°C, typical values are T = +25°C, see the schematic in the Functional Diagram. Limits are 100%
A
A
tested at T = +25°C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and
A
characterization.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Capacitive Load for
Each Bus Line
C
400
pF
B
SCL, SDA Input
Capacitance
C
6
pF
BIN
SCL Low Timeout
TIMING
30
ms
Time-Base Accuracy
SHA Calculation Time
t
T
= +25°C
-1
+1
10
%
ERR
A
t
4.5
ms
SHA
PRE
POR
Time between turning on the TH bias and
analog-to-digital conversions
TH Precharge Time
t
8.48
ms
Power-on-Reset Time
Task Period
t
(Note 7)
10
ms
ms
t
351.5
TP
Note 1: All voltages are referenced to CSP.
Note 2: Specification is Guaranteed by Design (GBD); not production tested.
Note 3: Write capacity numbers shown have one write subtracted for the initial write performed during manufacturing test to set
nonvolatile memory to a known value.
Note 4: Due to the nature of one-time programmable memory, write endurance cannot be production tested. Follow the nonvolatile
memory and SHA secret update procedures detailed in the data sheet.
Note 5: Timing must be fast enough to prevent the IC from entering shutdown mode due to bus being low for a period greater than the
shutdown timer setting.
Note 6: f
must meet the minimum clock low time plus the rise/fall times.
SCL
Note 7: The maximum t
can only be met if the device does not stretch the low period (t
) of the SCL signal.
LOW
HD:DAT
Note 8: This device internally provides a hold time of at least 100ns for the SDA signal (referred to as the minimum V of the SCL
IH
signal) to bridge the undefined region of the falling edge of SCL.
Note 9: Filters on SDA and SCL suppress noise spikes at the input buffers and delay the sampling instant.
Note 10: BATTS to CELL3, CELL3 to CELL2, CELL2 to CELL1, or CELL1 to CSP, cell voltages between 2.3V and 4.9V; BATTS and
CELL1 must be used. Neighbor CELL pins should be shorted if there is no battery connected between them.
Note 11: Specification is for TH1/TH2/TH3/TH4 channels.
www.maximintegrated.com
Maxim Integrated | 25
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Operating Characteristics
(T = +25°C, unless otherwise noted.)
A
www.maximintegrated.com
Maxim Integrated | 26
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Operating Characteristics (continued)
(T = +25°C, unless otherwise noted.)
A
www.maximintegrated.com
Maxim Integrated | 27
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Operating Characteristics (continued)
(T = +25°C, unless otherwise noted.)
A
www.maximintegrated.com
Maxim Integrated | 28
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Operating Characteristics (continued)
(T = +25°C, unless otherwise noted.)
A
www.maximintegrated.com
Maxim Integrated | 29
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Pin Configurations
WLP
TOP VIEW
(BUMP SIDE DOWN)
MAX17320X
1
2
3
4
5
6
+
A
B
C
D
E
BATTS
IN
CP
CHG
DIS
PCKP
SCL/
OD
CELL3
CELL2
CELL1
GND
TH4
TH3
NC
NC
NC
NC
ZVC
ALRT
SDA/
DQ
TH2
NC
NC
AOLDO
REG3
TH1
REG2
CSP
CSN
PFAIL
(30-BUMP WLP, 0.4mm PITCH)
www.maximintegrated.com
Maxim Integrated | 30
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
TQFN
TOP VIEW
MAX17320G
(24-PIN TQFN, 4mm x 4mm)
Pin Description
PIN
NAME
FUNCTION
WLP
TQFN
Power Supply Input. Connect to the positive terminal of cell stack with a 10Ω
resistor. Bypass with a 0.1µF/25V ceramic capacitor to GND.
A2
1
2
IN
Charge Pump Output and Bypass. Bypass CP to IN with a 0.47μF/25V ceramic
capacitor.
A3
A4
A5
CP
Charge FET Gate Control. Enable/disable the high-side CHG N-FET by driving the
gate between CP and IN. Connect a 0.1μF capacitor from Charge FET gate to
source.
3
4
CHG
DIS
Discharge FET Gate Control. Enable/disable the high-side DIS N-FET by driving
the gate between CP and PCKP.
www.maximintegrated.com
Maxim Integrated | 31
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Pin Description (continued)
PIN
NAME
FUNCTION
WLP
TQFN
Zero-Volt Charge Path. Recovery charge current is set by the resistor from the
PCKP pin to the ZVC pin. Leave ZVC open if not used.
B5
5
ZVC
A6
C5
6
7
PCKP
ALRT
Connect to Positive Terminal of Pack Connector Through 1kΩ
Programmable Alert Output
2
Serial Clock Input for I C Communication or Speed Selection for 1-Wire
2
Communication. Input only. For I C communication, connect to the clock terminal
B6
8
SCL/OD
of the battery pack. Connect to CSN for standard speed 1-Wire communication.
Connect to the REG3 pin for overdrive 1-Wire communication. SCL/OD has an
internal pulldown (IPD) for sensing pack disconnection.
2
Serial Data Input/Output for Both 1-Wire and I C Communication Modes. Open-
C6
D6
E6
9
SDA/DQ
TH1
drain output driver. Connect to the DATA terminal of the battery pack. SDA/DQ
has an internal pulldown (IPD) for sensing pack disconnection.
Thermistor Input 1. Connect a 10k/100k thermistor from TH1 to GND. Leave
disconnected or connect to GND if not used.
10
11
Permanent Failure Indicator. Connect to a three terminal fuse to take action in
case of primary FET failure detection. If not used, connect to GND with a 1kΩ
resistor.
PFAIL
Always-On LDO. Configurable as 3.4V or 1.8V. Bypass to GND with a 0.47µF/10V
ceramic capacitor. Connect to GND with a 10kΩ resistor if not used.
D5
E5
E4
E3
D2
E2
C2
B2
E1
12
13
14
15
16
17
18
19
20
AOLDO
REG3
CSN
Internal 3.4V Regulator Output. Bypass to GND with a 0.47µF/10V ceramic
capacitor.
System Ground and Current Measurement Negative Sense Point. Kelvin connect
to load side of the sense resistor.
Device Ground and Current Measurement Positive Sense Point. Kelvin connect to
cell side of the sense resistor.
CSP
Thermistor Input 2. Connect 10k/100k thermistor from TH2 to GND. Leave
disconnected or connect to GND if not used.
TH2
Internal 1.8V Regulator Output. Bypass to GND with a 0.47µF/10V ceramic
capacitor.
REG2
TH3
Thermistor Input 3. Connect a 10k/100k thermistor from TH3 to GND. Leave
disconnected or connect to GND if not used.
Thermistor Input 4. Connect a 10k/100k thermistor from TH4 to GND. Leave
disconnected or connect to GND if not used.
TH4
Ground Pin. Connect to ground. Do not share the ground trace with the CSP
Kelvin-sense trace.
GND
D1
C1
B1
21
22
23
CELL1
CELL2
CELL3
Cell Voltage Sense 1. Used for cell balancing and voltage sensing.
Cell Voltage Sense 2. Used for cell balancing and voltage sensing.
Cell Voltage Sense 3. Used for cell balancing and voltage sensing.
Battery Voltage Sense of Top Cell in Series Stack. Used for cell balancing and
voltage sensing.
A1
24
BATTS
No Connect. The NC pins are not internally connected and can be used for routing
vias in certain cases. B3, C3, D3 can take a via from ZVC and ALRT. B4, C4, D4
can take a via from TH2, TH3, TH4 and AOLDO. Other placement of the vias
under the NC pins could cause noise to couple to the IC.
B3, B4, C3,
C4, D3, D4
—
NC
www.maximintegrated.com
Maxim Integrated | 32
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Functional Diagrams
Block Diagram
3 TERM
FUSE
PACK+
1kΩ
PERMANENT
FAILURE
DETECTION
CHARGE DETECT
SHORT-CIRCUIT DETECT
SHORT-CIRCUIT REMOVE
PCKP
CHG
DIS
IN
BATT CP
CP
PCKP
PFAIL
PCKP PULLDOWN (PKSINK)
N
RZVC
INTERNAL SELF-DISCHARGE DETECT
10kΩ
ZVC
GND
ZVC PATH
PUMP
0.47µF
0.1µF
10Ω
AOLDO
3.4V OR 1.8V
0.47µF
AOLDO
OPTIONAL
ALWAYS-ON SUPPLY
IN
IN
OUT
IN
1.8V LDO
RBAL4
REG2
BATTS
OUT
0.47µF
0.47µF
0.1µF
0.1µF
MAX17320
9Ω
3.4V LDO
REG3
ALRT
IN
OUT
RBAL3
CELL3
9Ω
RBAL2
CELL2
MODELGAUGE M5
CORE
150Ω
150Ω
0.1µF
0.1µF
SDA/DQ
SCL/OD
9Ω
I2C/1-WIRE
INTERFACE
RBAL1
CELL1
MUX
INTERNAL
TEMPERATURE
SENSOR
REG3
4.7V
4.7V
9Ω
TH BIAS
OPTIONAL THERMISTORS
TH4
TH3
TH2
TH1
PCKP
CURRENT
COMPARATORS
GND
CSP
CSN
PACK-
RSENSE
www.maximintegrated.com
Maxim Integrated | 33
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Detailed Description
General Description
The MAX17320 is a 38μA I stand-alone pack-side fuel gauge IC with protector and optional SHA-256 authentication for
Q
2-, 3-, or 4-cell lithium-ion/polymer batteries which implements Maxim's ModelGauge m5 algorithm without requiring host
interaction for configuration. This makes the IC an excellent pack-side fuel gauge. The IC monitors the voltage, current,
temperature, and state of the battery to ensure that the lithium-ion/polymer battery is operating under safe conditions to
prolong the life of the battery. Voltage of each cell of the the battery pack is measured at the CSP or GND/CELL1/CELL2/
CELL3/BATTS connections. The total pack voltage is measured at BATTS and PCKP. Current is measured with an
external sense resistor placed between the CSP and CSN pins. Power and average power are also reported. Up to four
external NTC thermistor connections allow the IC to measure temperature of the cells in the battery pack by monitoring
the TH1-4 pins. The TH1-4 pins provide an internal pullup for the thermistor that is disabled internally when temperature
is not being measured. Internal die temperature of the IC is also measured and can be a proxy for the protection FET
temperature if they are located close by the IC.
The IC provides programmable discharge protection for overdischarge currents (fast, medium, and slow protection),
overtemperature, and undervoltage. The IC also provides programmable charge protection for overvoltage, over/
undertemperature, overcharge currents (fast and slow), cell imbalance, internal self-discharge, charge done, charger
communication timeout, precharge fault, and overcharge capacity fault. The IC provides a fast ideal diode discharge
response that allows the battery to provide energy to the system even while the charge fault persists. The IC provides
programmable charging current/voltage prescription following 6 JEITA temperature zones as well as step-charging. The
IC provides additional protection to permanently disable the battery by overriding a secondary protector or blowing a
fuse in severe fault conditions. This is useful when the IC has detected a primary protection FET failure and is unable to
block charge/discharge any other way. The IC also modulates the CHG FET to regulate prequalification charge current
until the cells cross the prequalification voltage threshold eliminating the need for external precharge circuit. Additional
functionality is described in the Protector section.
The IC supports a low-power shutdown mode. The IC enters this low-power mode by command or if communication
collapsed (if enabled). The IC wakes up from this low-power mode by communication (if battery voltage is above
the undervoltage threshold), charger detection, or pushbutton/system presence wakeup (if enabled and installed).
Pushbutton/system presence wakeup allows a pack to completely disconnect from a system during shipping, yet wakeup
immediately upon the user pressing the button or detecting the system presence, not needing the user to plug in a
charger.
The ModelGauge m5 algorithm combines the short-term accuracy and linearity of a coulomb counter with the long-
term stability of a voltage-based fuel gauge, along with temperature compensation to provide industry-leading fuel-gauge
accuracy. Additionally, the algorithm does not suffer from abrupt corrections that normally occur in coulomb-counter
algorithms, since tiny continual corrections are distributed over time. The IC automatically compensates for aging,
temperature, and discharge rate and provides accurate state-of-charge (SOC) in milliampere-hours (mAh) or percentage
(%) over a wide range of operating conditions. Fuel gauge error always converges to 0% as the cell approaches empty.
Dynamic power functionality provides the instantaneous maximum battery output power which can be delivered to the
system without violating the minimum system input voltage. The IC provides accurate estimation of time-to-empty and
time-to-full and provides three methods for reporting the age of the battery: reduction in capacity, increase in battery
resistance, and cycle odometer. In addition, age forecasting allows the user to estimate the expected lifespan of the cell.
The IC provides a configurable always-on LDO (1.8V or 3.4V) that can power small critical loads (less than 2mA) inside
the battery or on the system side without overloading the cells even under fault conditions.
To prevent battery clones, the IC integrates SHA-256 authentication with a 160-bit secret key. Every IC also incorporates
a 64-bit unique identification number (ROM ID). Additionally, up to 84 bytes of user memory (NVM) can be made available
to store custom information.
www.maximintegrated.com
Maxim Integrated | 34
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
2
Communication to the host occurs over a Maxim 1-Wire or standard I C/SMBus interface. SCL/OD is an input from the
host, and SDA/DQ is an open-drain I/O pin that requires an external pullup. The ALRT pin is an output that can be used
as an external interrupt to the host processor if voltage, current, temperature, state-of-charge, or protection conditions
(configurable) are detected. The IC offers a pushbutton feature that can be used to wake up the system after cutting
power off from the system using the protection FETs, for the purpose of extending the shelf life of the battery.
For additional reference material, refer to the following Application Notes:
Application Note 7177: MAX17320 Battery Pack Implementation Guide
Application Note 7161: MAX17320 Host Software Implementation Guide
Protector
Lithium-ion/polymer batteries are very common in a wide variety of portable electronic devices because they have very
high energy density, minimal memory effect and low self-discharge. However, care must be taken to avoid overheating
or overcharging these batteries to prevent damage to the batteries potentially resulting in dangerous outcomes/explosive
results. By operating in safe temperature ranges, at safe voltages and current levels, the overall safety of the lithium-ion/
polymer batteries can be assured throughout the life of the battery.
Simple protection schemes are available to protect a battery from exceeding the safe levels. These schemes include
protection for overdischarge current, short-circuit current, overcharge current, undervoltage, and overvoltage. The
next level of protection offers smart protection schemes which include protection for under OCV (SmartEmpty), long
overdischarge current, overtemperature limits for charge and discharge, undertemperature charge limits, and charge-
done protection. The IC provides all of these simple and smart protection schemes with programmable thresholds and
programmable timer delays for each fault.
The IC provides additional protection functionality beyond these schemes as follows:
Discharging Protection Functionality
● Overcurrent: (see nODSCCfg and nODSCTh)
• Fast Short-Circuit (70μs to 985μs): The short-circuit hardware comparator is programmable from 5mV to 155mV
with delay programmable from 70μs to 985μs.
• Medium (1ms to 15ms): The overdischarge current hardware comparator is programmable from 2.5mV to 77.5mV
with delay programmable from 1ms to 15ms.
• Slow (351ms to 35s): Slow overdischarge protection is programmable from 0mV to 51.2mV in 0.2mV steps with
delay programmable from 351ms to 35s (see nDelayCfg and nIPrtTh1).
● Overtemperature:
• Hot (OTPD—Overtemperature Discharge): Discharge overtemperature (OTPD, see nProtMiscTh) is separately
programmable from charge overtemperature (OTPC). OTPD is typically a higher temperature than OTPC, since
charging while hot is more hazardous than discharging. OTPD is programmable in 1°C steps, with a programmable
timer (see nDelayCfg), and is based on the hottest of the enabled thermistors.
• Die-Hot: The IC measures die temperature as well as up to four thermistor temperatures. Since the IC is
generally located close to the external FETs, the die temperature can indicate when the FETs are overheating. This
separately programmable threshold (see nProtMiscTh) blocks both charging and discharging.
• Permanent-Fail-Hot: When a severe overtemperature is detected, the fault is recorded into NVM and permanently
disables the charge and discharge FETs and blows the three terminal fuse if enabled.
● Undervoltage (UVP): Undervoltage is protected by two thresholds: UVP (undervoltage protect) and UOCVP (under
OCV protect—SmartEmpty) (see nUVPrtTh register for details).
www.maximintegrated.com
Maxim Integrated | 35
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Charging Protection Functionality:
● Overvoltage (OVP): Overvoltage protection is programmable with 20mV resolution (see nOVPrtTh). Temperature-
region dependent OVP protection is also provided for cold/room/warm and hot temperature regions (see nJEITAV).
OVP detection is debounced with a programmable timer (see nDelayCfg). An additional, higher OVP permanent
failure threshold is programmable, which records any excessive OVP into NVM and permanently disables the charge
and discharge FETs and blows the three terminal fuse if enabled.
● Charge Temperature Protection: Temperature protection thresholds are debounced with a programmable timer (see
nDelayCfg) and are based on the hottest and coldest of the enabled thermistors.
• Hot (OTPC): Charging temperature protection is programmable with 1°C resolution (see nTPrtTh1).
• Cold (UTP): Charging is blocked at cold, programmable with 1°C resolution (see nTPrtTh1).
Each threshold operates with a 1°C hysteresis.
● Overcharge-Current Protection:
• Fast: Overcharge current is detected by a programmable hardware comparator and debounce timer between 0mV
to 38.75mV and 1ms to 15ms thresholds.
• Slow: A lower and slower overcharge-current protection ensures that more moderate high currents do not persist
for a long time. Slow overcharge protection is programmable from 0mV to 51.2mV in 0.2mV steps, with an delay
programmable between 0.35s and 35s (see nDelayCfg and nIPrtTh1). Additionally, with nNVCfg1.enJP = 1, this
overcurrent-protection threshold is modulated according to temperature region (see nJEITAC).
● Charge-Done: If enabled, the IC turns off the charge FET whenever charge termination is detected according to
termination current and timeout. (See nDelayCfg and nIChgTerm). The charge FET is turned on when discharging
or charger removal is eventually detected. Also, charging resumes (charge FET turns on) if battery discharges below
programmable threshold (VFSOC < FullSOCThr).
● Charger-Communication Timeout: If enabled, during charging the IC turns off the charge FET if the host has
stopped communicating beyond a timeout configurable from 11s to 3 minutes (see nDelayCfg). In systems which
consult the battery for prescribing the charge current or charge voltage, especially to apply JEITA thresholds or step-
charging, this feature is useful to protect against uncontrolled charging after an operating system crash or shutdown.
● Overcharge-Capacity Fault: If any charge session delivers more charge (coulombs) to the battery than the expected
full design capacity, charging is blocked, if the feature is enabled. This threshold is programmable as a percentage
(see nProtMiscTh.QOvflwTh) beyond the design capacity.
● Cell Imbalance Fault: During charging the IC monitors the individual cell voltages and, if enabled, turns off the
charge FET if any cell imbalance is greater than programmable threshold (see nBalTh.Imbalance).
Other Faults:
● Nonvolatile CheckSum Failure: If enabled (nNVCfg1.enProtChkSm), the IC blocks charge and discharge when
startup checksum of protector NVM does not match the value stored in nProtCfg2.CheckSum.
www.maximintegrated.com
Maxim Integrated | 36
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Other Protection Functionality:
● Zero-Volt Charging: The IC allows charging when the battery voltage is at or above 4.2V (ZVC disabled). To enable
the charging of battery between 0.0V and 4.2V, ZVC must be enabled. A resistor between ZVC and PCKP is used to
enable ZVC and set the maximum recovery current. See the Zero-Volt Charging section for more details.
● Overdischarge-Removal Detection: Following any overdischarge current fault, after the IC turns off the discharge
FET, it tests for load removal by sourcing 30μA into PCKP. Load removal is detected when PCKP exceeds 1V. This
low threshold is intentionally below the startup voltage of most ICs in order to allow active loads by external ICs while
rejecting passive loads by resistors (short-circuit, failed components, etc.).
● Charger Removal Detection: Following any charge fault, after the IC turns off the charge FET, it measures
PCKP to detect the removal of the offending charger. Charger removal is detected when PCKP falls below BATT -
nOVPrtTh.ChgDetTh or whenever discharge current is detected.
● Battery Internal Self-Discharge Detection: The IC measures the internal self-discharge of the battery that might
indicate health or safety problems. The IC alerts the system or turns off the charge and discharge FETs when a
leakage is detected above the configurable threshold. See the Battery Internal Self-Discharge section for more details.
● Ideal-Diode Control: During any charge fault, the charge FET turns on when a discharge current is detected, with up
to 350ms delay. This ideal diode behavior reduces the heat and voltage drop associated with the body diode during
protection faults. All discharge-only faults are released when the charger is connected. See the Charger Presence
and Ideal Diode Behavior section for more details.
Protection Fault Reporting:
● Protection Fault Status: Each charge and discharge fault state is latched in the ProtStatus register. When the fault
is cleared, the corresponding bit is cleared.
● Protection Fault Alerts: The ProtAlrt register latches the status of any previous faults detected by the device. Once
a fault is detected, the corresponding bit remains set until it is cleared by the host. Additionally, the Status.ProtAlrt bit
is set when any ProtAlrt bit is set.
● Protection Fault Logging: The nFaultLog register also indicates which protection events happened during each
history log period.
Charging Prescription Registers: The ChargingVoltage and ChargingCurrent registers can guide the charger
according to a recommended charging profile. This can include the following knowledge which generally is associated
with a particular battery and may be stored in the battery with the IC:
● Factory Recommended Charging Current and Voltage: This is useful when a system involves multiple battery
vendors, swappable batteries, aftermarket batteries, or legacy system support.
● Charging Modifications According to Battery Temperature: Significantly above and below room temperature,
most cell manufacturers recommend charging at reduced current and lower termination voltage to assure safety and
improve lifespan. The IC modulates its guidance according to TooCold/Cold/Room/Warm/Hot/TooHot programmable
temperature regions (see nTPrtTh1/2/3). Both charging current and voltage are modulated at Cold/Warm/Hot,
targeting charge settings lower than Room (see nJEITAV and nJEITAC).
● Step-Charging: A common practice to balance lifespan and charge speed is to apply step-charging profiles (see the
Step-Charging section). The IC supports three programmable steps with programmable charge currents and voltages.
At a high level, the IC protector has dual state-machines as shown in Figure 1. Each charge and discharge fault state is
latched in the ProtStatus register, where each fault obeys a separate instance of the state machine shown in Figure 1.
Any single charge fault opens the charge FET to block charge current (charge faults are OR'd together). All charge faults
must be released to allow charge to resume (charge fault release conditions are AND'd together). The behavior is similar
for blocking discharge.
www.maximintegrated.com
Maxim Integrated | 37
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
CHARGE FAULT (OR’D)
BLOCK CHARGE
CHARGEGOOD = 0
ALLOW CHARGE
CHARGEGOOD = 1
CHARGE FET ENABLED IF
(NO CHARGE FAULTS OR DISCHARGING)
CHARGE FAULTS RELEASED (AND’D)
DISCHARGE FAULT (OR’D)
DISCHARGE FET ENABLED IF
(NO DISCHARGE FAULTS OR CHARGING)
BLOCK DISCHARGE
DISGOOD = 0
ALLOW DISCHARGE
DISGOOD = 1
DISCHARGE FAULTS RELEASED (AND’D)
Figure 1. Simplified Protector State Machine
The IC includes a write protection and a permanent locking function. The write protection prevents accidental overwrites
of protection parameters. This protection must be cleared before updating any registers and should be set after
configuration changes are made. The permanent locks prevent intentional or malicious tampering, and should be enabled
after development is completed and the battery pack is ready to ship in production. See the Memory Locks and Write
Protection section for more details.
The protector registers are summarized by their protection function in Table 1 and are graphically shown across the
various temperature ranges in Figure 2 and Figure 3.
Table 1. Summary of Protector Registers by Function
FUNCTION
REGISTER
Voltage Thresholds
Permanent Fail Overvoltage Protection
Overvoltage Protection
nOVPrtTh
nJEITAV, nOVPrtTh
nOVPrtTh
Overvoltage Protection Release
UnderOCV Protection
nUVPrtTh
Undervoltage Protection
Undervoltage Shutdown
Prequal Voltage
nUVPrtTh
nUVPrtTh
nChgCfg
www.maximintegrated.com
Maxim Integrated | 38
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 1. Summary of Protector Registers by Function (continued)
Current Thresholds
(See Figure 6 for timing details on current thresholds)
Fast Overcharge Protection
Slow Overcharge Protection
Slow Overdischarge Protection
Fast Overdischarge Protection
Short-Circuit Protection
Charging Detected
nODSCTh, nODSCCfg
nIPrtTh1
nIPrtTh1
nODSCTh, nODSCCfg
nODSCTh, nODSCCfg
nProtMiscTh
Discharging Detected
nProtMiscTh
Charge Termination Current
Temperature Thresholds
Fault Timers
nIChgTerm
nTPrtTh1, nTPrtTh2, nTPrtTh3, nProtMiscTh
nDelayCfg, nODSCCfg
nBalTh
Cell Balancing Thresholds
Charging Prescription
(ChargingCurrent, ChargingVoltage registers)
Charging Voltage
Charging Current
nJEITAV
nJEITAC
Prequal Current
nChgCfg
nStepChg
Step Charging
Protection Status/Configuration
nProtCfg, ProtStatus, nBattStatus, ProtAlrt, nFaultLog
www.maximintegrated.com
Maxim Integrated | 39
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
4.51V
PERM FAIL OVP
4.25V
OVERVOLTAGE
PROTECTION
STEP-CHARGING
4.21V
OVP RELEASE
JEITA CHARGING VOLTAGE
STEPV2
4.2V
CHARGING VOLTAGE
STEPV1
STEPV0
STEPV1
STEPV0
TOO COLD
COLD
ROOM
10 TEMPERATURE (°C) 40
3.7V
WARM
HOT
TOO HOT
45
55 75
90 85
0
COLD ROOM WARM HOT
CHARGING
VOLTAGE
4.14V
4.1V
4.2V
4.16V 4.14V 4.12V
4.1V 4.08V
4.18V 4.16V
DESIGN VOLTAGE
3.3V
VEMPTY
2.92V
STEPV1
STEPV0
4.06V 4.12V
UOCV PROTECTION
2.6V
UV PROTECTION AND PREQUAL VOLTAGE
2.3V
UV SHUTDOWN
4.2V (PACK VOLTAGE)
MINIMUM OPERATING VOLTAGE
Figure 2. Programmable Voltage Thresholds (Default Values Shown) (All Voltages are per Cell)
www.maximintegrated.com
Maxim Integrated | 40
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
7000mA
FAST OVERCHARGE PROTECTION
6000mA
SLOW OVERCHARGE
PROTECTION
STEP-CHARGING
CHARGING CURRENT
2000mA
CHARGING CURRENT
STEPCURR1
STEPCURR2
STEPCURR1
STEPCURR2
TOO
COLD
COLD
ROOM
WARM
HOT
TOO HOT
15mA
COLD ROOM WARM HOT
0.75C 1C 0.88C 0.625C
PRECHARGE
7.5mA CURRDET
CHARGING
CURRENT
STEPCURR1 0.38C C/2 0.44C 0.31C
STEPCURR2 0.19C C/4 0.22C 0.15C
10TEMPERATURE (°C) 35
45
60 70 75
80
-10
-6000mA
SLOW OVERDISCHARGE PROTECTION
-8000mA
FAST OVERDISCHARGE PROTECTION
-10000mA
SHORT-CIRCUIT PROTECTION
Figure 3. Programmable Current Thresholds (Default Values Shown With 5mΩ Sense Resistor)
Protector Thresholds
The IC provides for a variety of programmable protector thresholds that are stored in nonvolatile memory. These
thresholds are for voltage, current, temperature, and timer delays.
www.maximintegrated.com
Maxim Integrated | 41
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Voltage Thresholds
All of the voltage thresholds of the IC are shown graphically in Figure 2 and in table form with details of each threshold
and the registers used to set the various thresholds in Table 2. The description of each register provides additional
guidance for selection of the register value.
Table 2. Voltage Thresholds (All Voltages are per Cell)
EXAMPLE
(ALL
CONFIGURATION
NAME
DESCRIPTION
VOLTAGES
ARE PER
CELL)
REGISTERS
ChargingVoltage[temp] +
Permanent Fail Both FETs are permanently OFF after this threshold is exceeded
nOVPrtTh.(dOVP +
4.51V
Overvoltage
beyond PermFailTimer. PFAIL is driven high to blow fuse if enabled.
OVPPermFail)
Overvoltage
(With 4 JEITA
Zones)
Programmable Overvoltage at each JEITA zone. Delta V added to
ChargingVoltage (nJeitaV) to set the OVP fault threshold. 10 mV
step size. Protection range from 3.9V to 4.88V.
{4.14V/4.2V/
4.18V/4.16V} +
50mV
ChargingVoltage[temp] +
nOVPrtTh.dOVP
{4.19V/4.25V/
4.23V/4.21V}
- 10mV
Overvoltage
Release
Programmable release hysteresis. Fault released when VCell drops
below this threshold and discharging is detected.
Overvoltage -
nOVPrtTh.dOVPR
ChargeVoltage-
Room
ChargingVoltage output, 5mV resolution.
ChargingVoltage output, 10mV resolution.
ChargingVoltage output, 10mV resolution.
ChargingVoltage output, 10mV resolution.
nJEITAV.Room
4.20V
4.16V
4.18V
4.14V
ChargeVoltage-
Hot
nJEITAV.(Room - Hot)
ChargeVoltage-
Warm
nJEITAV.(Room -
Warm)
ChargeVoltage-
Cold
nJEITAV.(Room - Cold)
DesignVoltage
EmptyVoltage
SBS Design voltage, just for information if SBS is not enabled.
For fuel gauge only (not related to protection).
nDesignVoltage
nVEmpty
3.7V
3.0V
Under OCV
Protection
(SmartEmpty)
nUVPrtTh.(UVP +
Programmable under-OCV 40mV steps UVP to UVP+1.28V.
3.2V
2.7V
UOCVP)
Undervoltage
Protection
Programmable undervoltage 20mV steps 2.2V to 3.46V. Gauging
and communications works until undervoltage shutdown.
nUVPrtTh.UVP
Undervoltage
Release
Undervoltage fault persists until charger applied.
Undervoltage
Shutdown
Gauging and communications work until undervoltage shutdown.
nUVPrtTh.UVShdn
Hardware
Startup
Pack voltage
4.2V minimum
Zero-Voltage
Charging
Enabled by populating ZVC resistor. Charging current set by
resistor value.
0.0V
www.maximintegrated.com
Maxim Integrated | 42
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
SmartEmpty
Standard undervoltage protection protects the cell voltage from dropping below a certain threshold to protect the battery
from reaching an overdischarged state. When a lithium-ion/polymer cell stays in undervoltage state for a long time, it is
important to prevent the lithium-ion/polymer cell from eventually discharging to very deep discharged states like 2.0V or
even 0V. Staying in a deep-discharge state for a long time can result in a lithium-ion/polymer battery aging faster or going
into a hazardous state.
Therefore, the standard objective for lithium-ion/polymer protection when overdischarged is:
Protect from overdischarge by ensuring some small reserve capacity for long-term-storage survival after
protection.
The standard protection is a voltage choice, undervoltage protection (UVP).
The load on the battery greatly influences the state corresponding with the UVP threshold. When the cell voltage reaches
the UVP threshold and the protection circuit opens the discharge FET, the cell voltage relaxes to reveal the actual state
of the battery as shown in Figure 4. When heavy pulsed loads are placed on the cell, the cell voltage may reach the
undervoltage threshold when there is still ~15% of the battery capacity remaining which results in wasted run-time for the
application. Additionally, very small loads can allow the battery to be very deeply discharged, potentially damaging the
cell, before reaching the undervoltage threshold.
The IC provides SmartEmpty functionality which relies on the fuel gauge's reported state-of-charge to determine empty
in the application as opposed to using the predefined UVP threshold. SmartEmpty is not influenced by the load and
opens up the discharge FET when the battery reaches the empty state, as shown in Figure 5. The IC continues to protect
against higher loads from dropping the cell voltage below the lowered UVP threshold, as shown in Figure 5.
2C
(PULSE LOAD)
OCV = 3.7V
(~15% CAPACITY REMAINING)
OCV = 2.8V
C/24 (LIGHT LOAD)
(VERY DEEP DISCHARGE - UNDESIRABLE)
UVP = 2.7V
TIME
Figure 4. Standard Undervoltage Protection
www.maximintegrated.com
Maxim Integrated | 43
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
3C
(PULSE LOAD)
2C
(PULSE LOAD)
C/24 (LIGHT LOAD)
UOCVP = 3.2V
(SMART EMPTY - DESIRABLE)
UVP = 2.5V
TIME
Figure 5. SmartEmpty Protection
Current Thresholds
All of the current thresholds of the IC are shown graphically in Figure 3 and in table form with details of each threshold in
Table 3. The description of each register provides additional guidance for selection of the register value. See Figure 6 for
timing details on current thresholds.
Table 3. Current Threshold Summary
CONFIGURATION
CURRENT
ACTION RELEASE
DETAILS
REGISTERS
Overcharge
Current (fast)
nODSCTh,
nODSCCfg
Threshold 5-bit, 1.25mV steps to 38.75mV.
Delay programmable 4-bit, 1ms to 15ms in 0.9ms steps.
CHG off
Discharging
or charger
removal
detection
Overcharge
Current
(slow with 4
JEITA zones)
nIPrtTh1,
nDelayCfg
Programmable 0.4mV steps to 51.2mV. Delay programmable
351ms to 45s. Separate thresholds for 4 out of 6 JEITA zones.
CHG off
Overdischarge
Current (fast)
nODSCTh,
nODSCCfg
5-Bit, 2.5mV steps to 77.5mV.
Delay programmable 4-bit, 1ms to 15ms in 0.9ms steps.
DIS off
Charging or
Overdischarge
Current (slow)
load
removal
nIPrtTh1,
nDelayCfg
Programmable 0.4mV steps to 51.2mV. Delay programmable
351ms to 45s.
DIS off
detection
DIS off
Short-Circuit
Current
nODSCTh,
nODSCCfg
5-Bit, 5mV steps to 155mV.
Delay programmable 4-bit, 61μs + 70μs steps to 985μs.
Charging
Detected
See the Charger Presence and Ideal Diode Behavior section for
details.
Normal
See the Charger Presence and Ideal Diode Behavior section for
more details. When discharging is detected, overcharge current
faults release. Other charge faults such as OVP, OTP, UTP remain
set, however, the CHG FET turns on to prevent the heat and voltage
drop associated with the ~0.6V CHG FET body diode. An OVP fault
remains remembered (unreleased) until voltage falls and
discharging is also detected.
Discharging
Detected
Normal
www.maximintegrated.com
Maxim Integrated | 44
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Overcurrent Protection
The IC provides three levels of protection for overdischarge current events: fast, medium, and slow as shown in Figure
6. The IC also provides fast and slow levels of protection for overcharge-current protection. The fast and medium levels
of protection are provided by hardware comparators and the slow levels are based on the ADC readings.
The IC maintains the protection until the source of the fault has been removed. Overcharge-protection fault releases
when discharge is detected. Overdischarge current (fast or slow) or short-circuit current protection faults release when
PCKP rises above 1V, while the IC applies 30μA source current test to PCKP or when charger is detected. See the
Charger Presence and Ideal Diode Behavior section for details.
OVERCHARGE THRESHOLD
nODSCTH.OCTH (0 - 38.75mV)
ADC OVERCHARGE THRESHOLD
nIPRTTH1.OCCP (0 - 51.2mV)
DEBOUNCE TIME
ADC OVERDISCHARGE THRESHOLD
nIPRTTH1.ODCP (0 - 51.2mV)
OVERDISCHARGE THRESHOLD
nODSCTH.ODTH (0 - 77.5mV)
SLOW
(SECONDS, WITH 1% ACCURACY)
MEDIUM
(MILLISECONDS)
FAST
(MICROSECONDS)
SHORT-CIRCUIT THRESHOLD
nODSCTH.SCTH (0 - 155mV)
Figure 6. Fast, Medium, and Slow Overcurrent Protection
www.maximintegrated.com
Maxim Integrated | 45
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Fast Overcurrent Comparators
The IC contains three fast overcurrent comparators called Overdischarge (OD), Short-Circuit (SC), and Overcharge (OC)
that allow control protection. These comparators have programmable threshold levels and programmable debounced
delays. See Figure 7.
The nODSCTh register sets the threshold levels where each comparator trips. The nODSCCfg register enables each
comparator and sets their debounce delays. The nODSCCfg register also maintains indicator flags of which comparator
has been tripped. These register settings are maintained in nonvolatile memory if the nNVCfg1.enODSC bit is set.
Overcurrent Comparator Diagram
-
SCDLY
+
SCTH
SCi
+
ODSCCfg
OCDLY
OCDLY
-
OCi
OCTH
ODTH
ODi
-
+
-
CSN
CSP
RSENSE
Figure 7. Overcurrent Comparator Diagram
Slow Overcurrent Protection
The IC provides programmable thresholds for the slow overdischarge-current protection (ODCP) and overcharge-
current protection (OCCP). ODCP and OCCP can be configured to provide different levels of protection across the six
temperature zones as shown in Figure 3. ODCP and OCCP are set in nIPrtTh1 and nJeitaC.
Temperature Thresholds
The six temperature zones shown in Figure 2 and Figure 3 can be configured in the nTPrtTh1 (Too-hot and Too-cold),
nTPrtTh2 (Hot and Cold), and nTPrtTh3 (TPermFailHot and Twarm) registers.
www.maximintegrated.com
Maxim Integrated | 46
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Additional Protection Thresholds
The IC provides additional protection for suspending charge when full charge is detected or when communication with
a charger has stopped as described in Table 4. The IC can also detect if the CHG FET or DIS FET has failed and alert
the secondary protector to activate. Some chargers can request the desired charge voltage and charge current from the
battery. The IC provides a six-zone JEITA charge prescription that can be read by the charger from the ChargeVoltage
and ChargeCurrent registers.
Table 4. Additional Protection Thresholds
THRESHOLD
ACTION
CONDITIONS
FullDet Fault—if enabled (nProtCfg.FullEn) and charge termination criteria (see
ICHGTerm and charge termination).
Charge Suspend
CHG off
ChgWDT Fault—if enabled (nProtCfg.ChgWDTEn) and communications timeout.
FullDet Release—Discharge or charger removal detected.
Charge-Suspend
Release
Normal
ChgWDT Release—Communications or discharge or charger removal detected.
Activate secondary CHG off yet charge-current continues—if enabled (nProtCfg.PFEn and
protector nProtCfg.FETPFEn).
Charge FET Failure
Activate secondary DIS off yet discharge-current continues—if enabled (nProtCfg.PFEn and
Discharge FET Failure
protector
nProtCfg.FETPFEn).
Charge Voltage/Current
Prescription
Six-zone JEITA (four charge currents and voltages).
Two steps per JEITA zone.
Step Charging
Battery Internal Self-Discharge Detection (ISD)
A healthy lithium-ion/polymer battery has a very high coulombic-efficiency, typically greater than 99.9% (defined as
discharge mAh vs. charge mAh). Some portion of the charge capacity can be lost by internal self-discharge. This includes
natural aging, which is exacerbated if the battery stays at a high temperature and/or high state for long periods of time.
However, in a damaged battery, additional capacity can be lost (unavailable for discharge), and some portion of this
reflects permanent capacity loss. Unusual self-discharge in a lithium-ion/polymer battery might indicate health or safety
problems.
The MAX17320 internal self-discharge (ISD) detection feature measures battery leakage and provides the following
functions:
● Leakage Measurement. The LeakCurrRep register outputs the milliampere leakage measured across many days
and multiple charge termination events.
• Accurate leakage detection
• Low ppm false-positive rate at a 3mA threshold
• Detection during normal use
• No discharge depth or duration constraints
• Requires at least four full events, each separated by 20 hours or more
● Leakage Log. Leakage measurements are recorded in the battery-life-logging data. This reveals leakage vs. time for
any returned battery or for managing deployed packs.
● Leakage Alert. If enabled, when LeakCurrRep exceeds the programmable alert threshold, an LDET alert (see
ProtAlrt) is asserted.
● Leakage Fault. If enabled, when LeakCurrRep exceeds the programmable fault threshold, the protector disconnects
the battery.
www.maximintegrated.com
Maxim Integrated | 47
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Example of Internal Self-Discharge Detection
Figure 8 shows the current leakage the MAX17320 detects as a result of placing a 909Ω resistor across a cell to emulate
a battery with internal self-discharge over various temperatures.
Figure 8. Example of Internal Self-Discharge with Temperature Variation
Configuring ISD
Contact Maxim for configuring the ISD Feature. See the Battery Internal Self-Discharge Registers section for
configuration details.
www.maximintegrated.com
Maxim Integrated | 48
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Charger Presence and Ideal Diode Behavior
During a charge fault, if there is a discharge current, the current flows through the body diode of the CHG FET and
potentially overheats and damages the FET. To prevent this, the IC turns on the CHG FET when discharging is detected.
When a charger is detected, the CHG FET turns off again to continue protecting against the charge fault.
The IC uses several methods to detect charge and discharge to provide the following "Ideal Diode" discharge control
without forgetting a possible charge fault state such as OVP, OTP, or UTP. Overcharge current is fully released during a
discharge condition.
1. Fast CHG FET On. When discharge is detected, the CHG FET quickly turns on regardless of any charge fault
condition. This limits the heat due to the CHG FET body diode conduction.
• Current < -CurrDet. nProtMiscTh.CurrDet is normally configured to a setting of 2 to provide a clear threshold
relative to ADC noise. With a 5mΩ sense resistor, this corresponding to 15mA, provides sufficient sensitivity for
most active loads.
• PCKP < BATT + nOVPCfg.ChgDetTh (PCKP voltage falling only). Additionally, a comparator detects charger
removal to support better discharging detection even during small standby currents.
2. Fast CHG FET Off. When discharge to charge transition is detected while a charge fault (such as OTP/OVP/UTP)
remains latched, the CHG FET quickly turns off to prevent charging. Since the charge fault remains remembered (not
released by the discharging), the response happens quickly without waiting for the debounce timer.
3. Slow CHG FET On. The CHG Fet turns on when AvgCurrent < -AvgCurrDet. For default configuration with
5mΩ, AvgCurrDet is sensitive to 2.8mA discharge. The AvgCurrDet threshold follows the filter configuration
nFilterCfg.nCurr as well as the hibernate state and configuration according to Table 5 when using default
nProtMiscTh.CurrDet = 15mA.
Table 5. AvgCurrDet Threshold When Using 5mΩ and Default nProtMiscTh.CurrDet =
15mA
AVGCURRENT FILTER CONFIGURATION (NFILTERCFG.NCURR)
1 (0.7s)
8.44mA
15.0mA
15.0mA
2 (1.4s)
4.68mA
8.4mA
3 (2.8s)
4.68mA
8.4mA
4 (5.6s)
2.82mA
4.6mA
8.4mA
5 (11.25s)
2.82mA
4.6mA
6 (22.5s)
1.88mA
2.8mA
7 (45s)
1.88mA
2.8mA
4.6mA
8 (90s)
1.4mA
1.88mA
2.8mA
Active (0.351s)
Hibernate (1.4s)
Hibernate (2.8s)
15.0mA
15.0mA
8.4mA
4.6mA
4. Slow CHG FET Off. AvgCurrent > AvgCurrDet. If the CHG FET is on for any of the above reasons, the CHG FET
turns off while the charge fault persists and the average discharge current is less than AvgCurrDet.
www.maximintegrated.com
Maxim Integrated | 49
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Permanent Failure
The IC supports several types of faults which result in a permanent failure. When any enabled permanent failure is
detected, both FETs turn off and remain off regardless of power-cycling. When any permanent failure fault is detected,
the nBattStatus.PermFail bit is set in addition to the specific fault bit (also in nBattStatus), and both FET drivers are put
in the off state. Furthermore, the PFAIL output drives high to either drive an external fuse or latch a secondary protector.
This action is useful when FET failure is detected since charge and discharge can not be blocked in any other way.
The following permanent failure faults are supported whenever permanent failures are enabled (nProtCfg.PFEn = 1) and
the condition persists longer than the Permanent Fail debounce timer (nDelayCfg.PermFailTimer).
● FET Failures: Enable/disable this feature by configuring nProtCfg.FetPFEn.
• DIS FET Shorted: If discharging is detected during discharge fault, nBattStatus.DFETFs is set and written to NVM.
• CHG FET Shorted: If charging is detected during charge fault, nBattStatus.CFETFs is set and written to NVM.
• FET Open Failure: If either FET is detected open by the detection methods below:
• Detected By Discharge Fail: If DIS = On and V
< 1.5V and discharge current is not detected,
PCKP
nBattStatus.FETFo is set and written to NVM.
• Detected By Charge Fail: If CHG = On and DIS = On and V
> V
+ ChgDet and charge current is not
PCKP
BATT
detected, nBattStatus.FETFo is set and written to NVM.
● Severe Overvoltage Failure: If any cell voltage exceeds nOVPrtTh.OVPPermFail, nBattStatus.OVPF is set and
written to NVM. Disable by configuring nOVPrtTh.OVPPermFail to the maximum value of 5.12V (FF__h).
● Severe Overtemperature Failure: If Temp exceeds nTPrtTh3.TpermFailHot, nBattStatus.OTPF is set and written to
NVM. Disable by configuring OTPPermFail to the maximum value of 127°C (7F__h).
● Severe Battery Internal Self-Discharge Detection: If enabled to measure internal self-discharge and configured
to be treated as a severe fault when the leakage current exceeds the fault threshold (see the Battery Internal Self
Discharge Detection Registers for configuration details), nBattStatus.LDet is set and written to NVM.
● Nonvolatile Protector Checksum Failure: If enabled (nNVCfg1.enProtChkSum), during startup a checksum of
the protector configuration is calculated and compared against the nChkSum register. If the value mismatches,
nBattStatus.ChkSumF is set.
Charge Control
The IC provides zero-volt charging, prequalification charging and a charging prescription to instruct a charger about how
to charge the battery pack.
Zero-Volt Charging
When in undervoltage-protection, the IC turns both FETs off and then enters a low quiescent state. After a long time in the
undervoltage state, it is possible for the battery voltage to fall below the minimum 4.2V (pack voltage) operating voltage,
making it unable to wakeup by communications or pushbutton-wakeup. In this situation, an external charge voltage must
be applied to PCKP in order to wake up the IC. If enabled, the IC allows a small recovery current to gently recover the
battery voltage.
The recovery current is set by the R
resistor between the PCKP and ZVC pins as shown in Figure 9. Zero-volt charge
ZVC
recovery can be disabled by depopulating the resistor. The maximum recovery current is calculated as:
Maximum Recovery Current = VOLTAGE /(R + R ).
PACK+ ZVC
IN
When the battery is severely depleted and the IC detects that a charger has been connected, the ZVC path is enabled
and the recovery current begins to flow as shown in Figure 9. The recovery current continues until the IC determines that
the battery voltage has recovered enough to transfer control to the prequalification or normal charge control at which time
it disconnects the ZVC path.
www.maximintegrated.com
Maxim Integrated | 50
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
PACK+
RPCKP
1kΩ
CHG
DIS
PCKP
ZERO-VOLT RECOVERY CURRENT PATH
IN
ZVC
RIN
10Ω
RZVC
BATT+
Figure 9. Zero-Volt Charge Recovery
Prequal Charging
The IC provides a prequal charge feature which modulates and reuses the charge NFET to control a limited and
configurable prequal current when the battery voltage is low. This eliminates the need for a third power FET. See the
Prequal Configuration for prequal voltage and current settings.
Charging Prescription
The IC provides appropriate charging voltage and charging current to safely charge the battery depending on the state of
the battery and the temperature. The ChargingVoltage and ChargingCurrent registers provide the information according
to the recommended charging based on knowledge that is installed in the battery. This information can be stored in the
IC to provide the recommended charging current and voltage. This is useful when a system involves multiple battery
vendors, swappable batteries, aftermarket batteries, or legacy system support.
As the temperature of the battery changes significantly above and below room temperature, most cell manufacturers
recommend charging at reduced current and lower termination voltage to assure safety and improve lifespan. The IC can
be configured to change its guidance according to TooCold/Cold/Room/Warm/Hot/TooHot programmable temperature
zones (see nTPrtTh1/2/3). Both charging current and voltage are updated at Cold/Warm/Hot (see nJEITAV and
nJEITAC). See Figure 2 and Figure 3.
Additionally, the IC provides a step-charging prescription to improve the lifespan of the battery and charge speed by
applying a step-charging profile (see the Step Charging section) as shown in Figure 10.
www.maximintegrated.com
Maxim Integrated | 51
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Step Charging
A step-charging profile sets three charge voltages, three corresponding charge currents, and manages a state-machine
to transition through the stages as shown in Figure 10.
FULL VOLTAGE
TH1 = FULL VOLTAGE – STEPDV1
TH0 = FULL VOLTAGE – STEPDV0
90%
SOC
50%
30%
SOC
HIGHEST CURRENT,
LOWEST VOLTAGE
REDUCED CURRENT UNTIL FULL
MEDIUM CURRENT
TIME
PROTTMRSTAT.CHARGESTEP
VCELL > TH0
VCELL > TH1
STAGE 0
STAGE 1
STAGE 2
NOT CHARGING/DISCHARGING
NOT CHARGING/DISCHARGING
Figure 10. Step-Charging State Machine
This breaks charging into three stages:
Stage 0: Highest current, lowest voltage. ChargingCurrent comes from nJEITAC until VCell > StepVolt0. After VCell >
StepVolt0, ChargingCurrent becomes defined by Stage 1.
Stage 1: Medium current. ChargingCurrent comes from nJEITAC x (StepCurr1 + 1)/16, which is a ratio from 1/16 to 16/
16 until VCell > StepVolt1. When VCell > StepVolt1, ChargingCurrent becomes defined by Stage 2.
Stage 2: Reduced current until full. ChargingCurrent comes from nJEITAC x (StepCurr2 + 1)/16, which is a ratio from 1/
16 to 16/16 until full.
For example, a charge may start with a ChargingCurrent of 2000mA until the cell voltage reaches 4.12V. At that point,
the ChargingCurrent is reduced to 1000mA until the cell voltage reaches 4.16V. Then, the ChargingCurrent is further
reduced to 500mA where it remains until the current begins to taper off naturally to the termination current.
www.maximintegrated.com
Maxim Integrated | 52
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
2
Disabling FETs by Pin-Control or I C Command
2
The IC provides FET override control by either I C command or pin-command to the ALRT pin. This functionality can be
useful for various types of applications:
● Factory Testing. Disconnecting the battery is useful for testing with a controlled external power supply.
● Battery Selection. In a multiple battery system, one battery can be disconnected and another connected by operating
the FETs.
● Ship Mode. The last step in the battery or system factory could be to disable the FETs to disconnect power to the
system to prevent the battery from draining during shipment, or when the system is in the warehouse or store shelf.
When allowed by Nonvolatile configuration, both FETs can be turned off by pin control or either FET can be individually
2
turned off by I C command. The control operates as follows:
● ALRT Pin Override. Set nProtCfg.OvrdEn = 1 and drive ALRT low to force both FETs into the off state. Releasing
the ALRT line recovers the FETs according to the protector's fault state machine. Alert pin output is not functional in
this mode.
2
● I C Command Override. Set nProtCfg.CmOvrdEn = 1 and write CommStat.CHGOff or CommStat.DISOff to
independently disable either the charge or discharge FET. Clearing CHGOff and DISOff recovers the FETs according
to the protector's fault state machine.
These features can be disabled and locked by nonvolatile memory to prevent system code from disabling the FETs.
Although disabling FETs does not produce any safety issue, it can be a nuisance if system-side software denies power
to the system.
Fuel Gauge
ModelGauge m5 Algorithm
Classical coulomb-counter-based fuel gauges have excellent linearity and short-term performance. However, they suffer
from drift due to the accumulation of the offset error in the current-sense measurement. Although the offset error is
often very small, it cannot be eliminated, causes the reported capacity error to increase over time, and requires periodic
corrections. Corrections are usually performed at full or empty. Some other systems also use the relaxed battery voltage
to perform corrections. These systems determine the true state-of-charge (SOC) based on the battery voltage after a
long time of no current flow. Both have the same limitation; if the correction condition is not observed over time in the
actual application, the error in the system is boundless. The performance of classic coulomb counters is dominated by
the accuracy of such corrections. Voltage measurement based SOC estimation has accuracy limitations due to imperfect
cell modeling, but does not accumulate offset error over time.
The IC includes an advanced voltage fuel gauge (VFG), which estimates OCV, even during current flow, and simulates
the nonlinear internal dynamics of a Li+ battery to determine the SOC with improved accuracy. The model considers
the time effects of a battery caused by the chemical reactions and impedance in the battery to determine SOC. This
SOC estimation does not accumulate offset error over time. The IC performs a smart-empty-compensation algorithm
that automatically compensates for the effects of temperature and load conditions to provide accurate state-of-charge
information. The converge-to-empty function eliminates error toward empty state. The IC learns battery capacity over time
automatically to improve long-term performance. The age information of the battery is available in the output registers.
The ModelGauge m5 algorithm combines a high-accuracy coulomb counter with a VFG. See Figure 11. The
complementary combined result eliminates the weaknesses of both the coulomb counter and the VFG while providing
the strengths of both. A mixing algorithm weighs and combines the VFG capacity with the coulomb counter and weighs
each result so that both are used optimally to determine the battery state. In this way, the VFG capacity result is used to
continuously make small adjustments to the battery state, canceling the coulomb-counter drift.
www.maximintegrated.com
Maxim Integrated | 53
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
MODELGAUGE
COULOMB COUNTER
VERY SLOW
INFLUENCE
Δ% SOC
ΔQ
MICRO-
CORRECTIONS
CAPACITY
FULL, EMPTY, AND STANDBY
STATE DETECTION
UNNECESSARY
Figure 11. Merger of Coulomb Counter and Voltage-Based Fuel Gauge
The ModelGauge m5 algorithm uses this battery state information and accounts for temperature, battery current, age,
and application parameters to determine the remaining capacity available to the system. As the battery approaches the
critical region near empty, the ModelGauge m5 algorithm invokes a special error correction mechanism that eliminates
any error.
The ModelGauge m5 algorithm continually adapts to the cell and application through independent learning routines. As
the cell ages, its change in capacity is monitored and updated and the voltage-fuel-gauge dynamics adapt based on cell-
voltage behavior in the application.
www.maximintegrated.com
Maxim Integrated | 54
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
VOLTAGE
CURRENT
TIME
OCV TABLE
LOOKUP
% REMAINING
OUTPUT
OCV
COULOMB
COUNTER
mAH OUTPUT
OCV
CALCULATION
OCV OUTPUT
TEMPERATURE
COMPENSATION
LEARN
RELAXED
CELL
DETECTION
CAPACITY LEARN
mAh PER PERCENT
×
EMPTY DETECTION
MIXING ALGORITHM
mAH OUTPUT
MIXCAP REGISTER
MIXSOC REGISTER
APPLICATION
EMPTY
COMPENSATION
BASED ON APPLICATION
TEMPERATURE AND
DISCHARGE RATE
EMPTY
COMPENSATION
LEARNING
+
+
-
END-OF-CHARGE
DETECTION
APPLICATION
OUTPUTS:
CELL CHEMISTRY
OUTPUTS:
REPSOC REGISTER
REPCAP REGISTER
AVSOC REGISTER
AVCAP REGISTER
TTE / AtTTE / TTF REGISTERS
FULLCAP REGISTER
VFOCV REGISTER
CYCLES REGISTER
FULLCAPNOM REGISTER
AGE REGISTER
Figure 12. ModelGauge m5 Block Diagram
ModelGauge m5 EZ Performance
ModelGauge m5 EZ performance provides plug-and-play operation of the IC. While the IC can be custom tuned to the
applications battery through a characterization process for ideal performance, the IC has the ability to provide reasonable
performance for most applications with no custom characterization required.
While EZ performance provides reasonable performance for most cell types, some chemistries such as lithium-iron-
phosphate (LiFePO ) and Panasonic NCR/NCA series cells require custom characterization for best performance. EZ
4
performance provides models for applications with empty voltages ranging from 3.0V to 3.4V through the EV kit GUI
Configuration Wizard. Contact Maxim for details of the custom characterization procedure.
www.maximintegrated.com
Maxim Integrated | 55
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
OCV Estimation and Coulomb Count Mixing
The core of the ModelGauge m5 algorithm is a mixing algorithm that combines the OCV state estimation with the coulomb
counter. After power-on reset of the IC, coulomb-count accuracy is unknown. The OCV state estimation is weighted
heavily compared to the coulomb count output. As the cell progresses through cycles in the application, coulomb-counter
accuracy improves and the mixing algorithm alters the weighting so that the coulomb-counter result is dominant. From
this point forward, the IC switches to servo mixing. Servo mixing provides a fixed magnitude continuous error correction to
the coulomb count, up or down, based on the direction of error from the OCV estimation. This allows differences between
the coulomb count and OCV estimation to be corrected quickly. See [[Voltage and Coulomb Count Mixing]].
The resulting output from the mixing algorithm does not suffer accumulation drift from current measurement offset
error and is more stable than a stand-alone OCV estimation algorithm. See Figure 13. Initial accuracy depends on the
relaxation state of the cell. The highest initial accuracy is achieved with a fully relaxed cell.
MAXIMUM COULOMB COUNTER ERROR
(±0.1% PER HOUR IN THIS EXAMPLE)
TYPICAL OCV ESTIMATION
ERROR AS CELL IS CYCLED
(SHADED AREA)
MODELGAUGE OCV + COULOMB COUNT
MIXING MAXIMUM ERROR RANGE
TIME
Figure 13. ModelGauge m5 Typical Accuracy Example
Empty Compensation
As the temperature and discharge rate of an application changes, the amount of charge available to the application also
changes. The ModelGauge m5 algorithm distinguishes between the remaining capacity of the cell, remaining capacity of
the application, and reports both results to the user.
The MixCap output register tracks the charge state of the cell. This is the theoretical mAh of charge that can be removed
from the cell under ideal conditions—extremely low discharge current and independent of cell voltage. This result is not
affected by application conditions such as cell impedance or minimum operating voltage of the application. ModelGauge
m5 continually tracks the expected empty point of the application in mAh. This is the amount of charge that cannot be
removed from the cell by the application because of the minimum voltage requirements and internal losses of the cell.
The IC subtracts the amount of charge not available to the application from the MixCap register and reports the result in
the AvCap register.
www.maximintegrated.com
Maxim Integrated | 56
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Since the available remaining capacity is highly dependent on the discharge rate, the AvCap register can be subject to
large instantaneous changes as the application load current changes. The result can increase, even while discharging if
the load current suddenly drops. This result, although correct, can be very counter-intuitive to the host software or end-
user. The RepCap output register contains a filtered version of AvCap that removes any abrupt changes in remaining
capacity. RepCap converges with AvCap over time to correctly predict the application empty point while discharging or
the application full point while charging. Figure 14 shows the relationship of these registers.
LOAD INCREASES
MIXCAP REGISTER
ABSOLUTE mAh STATE-OF-BATTERY NOT
CONSIDERING TEMPERATURE AND DISCHARGE
RATE
(I.E., CAPACITY AVAILABLE IF VERY LIGHT LOAD)
INCREASE IN AVAILABLE CAPACITY WHEN
AVCAP REGISTER
AVAILABLE CAPACITY OF THE
CELL UNDER PRESENT
UNDER LOAD IS COUNTERINTUITIVE TO
USERS AND OPERATING SYSTEMS
CONDITIONS
REPCAP REGISTER
REPORTED CAPCITY WITH NO SUDDENT
JUMPS AND CORRECT FORECAST OF
EMPTY
EMPTY
TIME (h)
Figure 14. Handling Changes in Empty Calculation
End-of-Charge Detection
The IC detects the end of a charge cycle when the application current falls into the band set by the IChgTerm register
value while the VFSOC value is above the FullSOCThr register value. By monitoring both the Current and AvgCurrent
registers, the device can reject false end-of-charge events such as application load spikes or early charge-source
removal. See the End-of-Charge Detection graph in the Typical Operating Characteristics and Figure 15. When a proper
end-of-charge event is detected, the device learns a new FullCapRep register value based on the RepCap register
output. If the old FullCapRep value was too high, it is adjusted on a downward slope near the end-of-charge as defined
by the MiscCfg.FUS setting until it reaches RepCap. If the old FullCapRep was too low, it is adjusted upward to match
RepCap. This prevents the calculated state-of-charge from ever reporting a value greater than 100%. See Figure 16.
Charge termination is detected by the IC when the following conditions are met:
• VFSOC register > FullSOCThr register
• AND IChgTerm x 0.125 < Current register < IChgTerm x 1.25
• AND IChgTerm x 0.125 < AvgCurrent register < IChgTerm x 1.25
www.maximintegrated.com
Maxim Integrated | 57
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
AVGCURRENT
CURRENT
1.25 x ICHGTERM
0.125 x ICHGTERM
0mA
HIGH CURRENT LOAD SPIKES DO NOT GENERATE
END-OF-CHARGE DETECTION BECAUSE CURRENT
AND AVERAGE CURRENT READINGS DO NOT FALL
INTO THE DETECTION AREA AT THE SAME TIME.
AVGCURRENT
CURRENT
1.25 x ICHGTERM
0.125 x ICHGTERM
0mA
EARLY CHARGER REMOVAL DOES NOT GENERATE
END-OF-CHARGE DETECTION BECAUSE CURRENT
AND AVERAGE CURRENT READINGS DO NOT FALL
INTO THE DETECTION AREA AT THE SAME TIME.
Figure 15. False End-of-Charge Events
www.maximintegrated.com
Maxim Integrated | 58
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
AVGCURRENT
CURRENT
1.25 x ICHGTERM
0.125 x ICHGTERM
0mA
CORRECT
END-OF-CHARGE
DETECTION AREA
CASE 1: OLD FULLCAPREP TOO HIGH
NEW FULLCAPREP
CASE 2: OLD FULLCAPREP TOO LOW
REPCAP
Figure 16. FullCapRep Learning at End-of-Charge
Fuel Gauge Learning
The IC periodically makes internal adjustments to cell characterization and application information to remove initial error
and maintain accuracy as the cell ages. These adjustments always occur as small under-corrections to prevent instability
of the system and prevent any noticeable jumps in the fuel-gauge outputs. Learning occurs automatically without any
input from the host. In addition to estimating the battery’s state-of-charge, the IC observes the battery’s relaxation
response and adjusts the dynamics of the voltage fuel gauge. Registers used by the algorithm include:
• Application Capacity (FullCapRep Register). This is the total capacity available to the application at full, set through
the IChgTerm and FullSOCThr registers as described in the End-of-Charge Detection section. See the FullCapRep
register description.
• Cell Capacity (FullCapNom Register). This is the total cell capacity at full, according to the voltage fuel gauge. This
includes some capacity that is not available to the application at high loads and/or low temperatures. The IC periodically
compares percent change based on an open circuit voltage measurement vs. coulomb-count change as the cell charges
and discharges, maintaining an accurate estimation of the pack capacity in mAh as the pack ages. See Figure 17.
• Voltage Fuel-Gauge Adaptation. The IC observes the battery’s relaxation response and adjusts the dynamics of the
voltage fuel gauge. This adaptation adjusts the RComp0 register during qualified cell relaxation events.
• Empty Compensation. The IC updates internal data whenever cell empty is detected (VCell < VEmpty) to account for
cell age or other cell deviations from the characterization information.
www.maximintegrated.com
Maxim Integrated | 59
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
RELAXATION EVENTS
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
D%4
D%1
D%5
OBSERVED SIZE OF BATTERY:
D%2
DQACC
FULLCAPNOM =
x 100%
DPACC
WHERE:
D%3
0%
DQACC=|DQ1|+|DQ2| +|DQ3| ...
DPACC=|D%1|+|D%2| +|D%3| ...
DQ4
1200mAh
1100mAh
1000mAh
900mAh
DQ1
DQ5
800mAh
700mAh
600mAh
500mAh
400mAh
300mAh
200mAh
100mAh
DQ2
DQ3
0mAh
Figure 17. FullCapNom Learning
Converge-To-Empty
The IC includes a feature that guarantees the fuel gauge output converges to 0% as the cell voltage approaches the
empty voltage. As the cell's voltage approaches the expected empty voltage (AvgVCell approaches VEmpty) the IC
smoothly adjusts the rate of change of RepSOC so that the fuel gauge reports 0% at the exact time the cell's voltage
reaches empty. This prevents minor over or under-shoots in the fuel gauge output. See Figure 18.
www.maximintegrated.com
Maxim Integrated | 60
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
VEMPTY
REPSOC
ESTIMATION TOO HIGH
REPSOC RATE-OF-
IDEAL
CHANGE ADJUSTED SO
REPSOC
THAT IT REACHES 0%
AS THE CELL’S
VOLTAGE REACHES
VEMPTY
REPSOC
ESTIMATION TOO LOW
0%
Figure 18. Converge-to-Empty
Determining Fuel-Gauge Accuracy
To determine the true accuracy of a fuel gauge, as experienced by end-users, the battery should be exercised in a
dynamic manner. The end-user accuracy cannot be understood with only simple cycles. To challenge a correction-
based fuel gauge, such as a coulomb counter, test the battery with partial loading sessions. For example, a typical user
may operate the device for 10 minutes and then stop use for an hour or more. A robust test method includes these
kinds of sessions many times at various loads, temperatures, and duration. Refer to the Application Note 4799: Cell
Characterization Procedure for a ModelGauge m3/ModelGauge m5 Fuel Gauge.
Initial Accuracy
The IC uses the first voltage reading after power-up or after cell is connected to the IC to determine the starting output of
the fuel gauge. It is assumed that the cell is fully relaxed prior to this reading; however, this is not always the case. If there
is a load or charge current at this time, the initial reading is compensated using the characterized internal impedance of
the cell to estimate the cell's relaxed voltage. If the cell was recently charged or discharged, the voltage measured by the
IC may not represent the true state-of-charge of the cell, resulting in initial error in the fuel gauge outputs. In most cases,
this error is minor and is quickly removed by the fuel-gauge algorithm during the first hour of normal operation.
www.maximintegrated.com
Maxim Integrated | 61
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Cycle+ Age Forecasting
A special feature of the ModelGauge m5 algorithm is the ability to forecast the number of cycles a user is able to get out
of the cell during its lifetime. This allows an application to adjust a cell's charge profile over time to meet the cycle life
requirements of the cell. See Figure 19. The algorithm monitors the change in cell capacity over time and calculates the
number of cycles it takes for the cell’s capacity to drop to a predefined threshold of 85% of the original. Remaining cycles
below 85% of the original capacity are unpredictable and not managed by age forecasting.
INITIAL DATA
CHARGE PROFILE
100%
CHANGED
ADDITIONAL DATA
NEW AGE FORECAST SHOWS
THAT APPLICATION
REQUIREMENTS SHOULD BE MET
INITIAL AGE FORECAST
SHOWS THAT APPLICATION
REQUIREMENTS MAY NOT
BE MET
MINIMUM CELL CAPACITY
REQUIRED BY THE
APPLICATION
CYCLES
Figure 19. Benefits of Age Forecasting
nAgeFcCfg Register (1E2h)
Register Type: Special
Nonvolatile Restore: There is no associated restore location for this register.
The nAgeFcCfg register is used to configure the age forecasting functionality. Register data is nonvolatile and is typically
configured only once during pack assembly. Table 6 shows the register format.
Table 6. nAgeFcCfg Register (1E2h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DeadTargetRatio
CycleStart
0
0
0
1
1
DeadTargetRatio: Sets the remaining percentage of initial cell capacity where the cell is considered fully aged.
DeadTargetRatio can be adjusted between 75% and 86.72% with an LSb of 0.7813%. For example, if age forecasting
was configured to estimate the number of cycles until the cell’s capacity dropped to 85.1574% of when it was new,
DeadTargetRatio should be programmed to 1101b.
www.maximintegrated.com
Maxim Integrated | 62
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
CycleStart: Sets the number of cell cycles before age forecasting calculations begin. CycleStart has a range of 0.00
to 81.92 cycles with an LSb of 0.64 cycles. Since age forecasting estimation becomes more accurate over time, most
applications use a default value of 30 cycles.
0: Always write this location 0.
1: Always write this location 1.
AgeForecast Register (0B9h)
Register Type: Special
Nonvolatile Backup: None
The AgeForecast register displays the estimated cycle life of the application cell. The AgeForecast value should be
compared against the Cycles (017h) register to determine the estimated number of remaining cell cycles. This is
accomplished by accumulating the capacity loss per cycle as the cell ages. The result becomes more accurate with each
cycle measured. The AgeForecast register has a full range of 0 cycles to 16383 cycles with a 25% LSb. This register is
recalculated from learned information at power-up.
Age Forecasting Requirements
There are several requirements for proper operation of the age forecasting feature as follows:
1. There is a minimum and maximum cell size that the age forecasting algorithm can handle. Table 7 shows the allowable
range of cell sizes that can be accurately age forecasted depending on the size of the sense resistor used in the
application. Note this range is different from the current and capacity measurement range for a given sense resistor. See
the Current Measurement section for details.
2. Age forecasting requires a minimum of 100 cycles before achieving reasonable predictions. Ignore the age forecasting
output until then.
3. Age forecasting requires a custom characterized battery model to be used by the IC. Age forecasting is not valid when
using the default model.
Table 7. Minimum and Maximum Cell Sizes for Age Forecasting
SENSE RESISTOR
(Ω)
MINIMUM CELL SIZE FOR FORECASTING
(mAH)
MAXIMUM CELL SIZE FOR FORECASTING
(mAH)
0.005
0.010
0.020
1600
800
5000
2500
1250
400
Enabling Age Forecasting
The following steps are required to enable the age forecasting feature:
1. Set nNVCfg2.enVT = 0. This function conflicts with age forecasting and must be disabled.
2. Set nFullCapFlt to the value of nFullCapNom.
3. Set nVoltTemp to 0001h.
4. Set nNVCfg0.enAF = 1 to begin operation.
www.maximintegrated.com
Maxim Integrated | 63
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Battery Life Logging
The IC has the ability to log learned battery information providing the host with a history of conditions experienced by the
cell pack over its lifetime. The IC can store up to 100 snapshots of page 1Ah in nonvolatile memory. Individual registers
from page 1Ah are summarized in Table 8. Their nonvolatile backup must be enabled in order for logging to occur. See
each register's detailed description in other sections of this data sheet. The logging rate follows the "Fibonacci Saving"
interval to provide recurring log-saving according to the expected battery lifespan and is configured as shown in Table
96. See the 100 Record Life Logging section for more details.
Table 8. Life Logging Register Summary
REGISTER
ADDRESS
REGISTER
NAME
FUNCTION
1A0h
1A1h
1A2h
1A3h
1A4h
1A5h
1A6h
1A7h
1A8h
1A9h
nQRTable00
nQRTable10
nQRTable20
nQRTable30
nCycles
Learned characterization information used to determine when the cell pack is empty under
application conditions.
Total number of equivalent full cycles seen by the cell since assembly.
nFullCapNom Calculated capacity of the cell independent of application conditions.
nRComp0
Learned characterization information related to the voltage fuel gauge.
nTempCo
nBattStatus
Contains the permanent battery status information and, if enabled, the leakage current.
nFullCapRep Calculated capacity of the cell under present application conditions.
The average voltage and temperature seen by the IC at the instance of learned data backup. If Age
Forecasting is enabled, this register contains different information.
1AAh
nVoltTemp
1ABh
1ACh
1ADh
nMaxMinCurr
Maximum and minimum current, voltage, and temperature seen by the IC during this logging
nMaxMinVolt
window.
nMaxMinTemp
If Fault Logging is enabled, this register indicates which protection events happened during each
1AEh
1AFh
nFaultLog
nTimerH
history log period. If Age Forecasting is enabled, this register contains a highly filtered
nFullCapNom.
Total elapsed time since cell pack assembly not including time spent in shutdown mode.
www.maximintegrated.com
Maxim Integrated | 64
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Life Logging Data Example
Figure 20 shows a graphical representation of sample history data read from an IC. Analysis of this data can provide
information about cell performance over its lifetime as well as to detect any application anomalies that may have affected
performance.
6m
TIME VS. CYCLES AND MAXIMUM / MINIUMUM
VOLTAGE GIVES AN INDICATION OF THE USAGE PROFILE
0
4.2V
3.0V
85C
-40C
2.0A
MAXIMUM / MINUMUM TEMPERATURE AND CURRENT
CAN INDICATE IF THE CELL HAS BEEN ABUSED
-5.0A
100%
FULLCAPNOM
FULLCAPREP
QRESIDUAL
0%
CYCLES
Figure 20. Sample Life Logging Data
www.maximintegrated.com
Maxim Integrated | 65
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Determining Number of Valid Logging Entries
While logging data, the IC begins on history page 1 and continues until all history memory has been used at page 100.
Prior to reading history information out of the IC, the host must determine which history pages has been written and
which, if any, had write errors and should be ignored. Each page of history information has two associated write flags
that indicate if the page has been written and two associated valid flags which indicate if the write was successful. The
HISTORY RECALL command [E2XXh] is used to load the history flags into page 1Fh of IC memory where the host can
then read their state. Table 9 shows which command and which page 1Fh address has the flag information for a given
history page. For example, to see the write flag information of history pages 1-8, send the E29Ch command then read
address 1F2h. To see the valid flag information of pages 1-8, send the E29Ch command and then read address 1FFh.
Table 9. Reading History Page Flags
ASSOCIATED
HISTORY PAGES
COMMAND TO RECALL
WRITE FLAGS
WRITE FLAG
ADDRESS
COMMAND TO RECALL
VALID FLAGS
VALID FLAG
ADDRESS
1-8
1F2h
1F3h
1F4h
1F5h
1F6h
1F7h
1F8h
1F9h
1FAh
1FBh
1FCh
1FDh
1FEh
E29Ch
1FFh
1F0h
1F1h
1F2h
1F3h
1F4h
1F5h
1F6h
1F7h
1F8h
1F9h
1FAh
1FBh
9-16
17-24
25-32
33-40
41-48
49-56
57-64
65-72
73-80
81-88
89-96
97-100
E29Ch
E29Dh
Once the write flag and valid flag information are read from the IC, it must be decoded. Each register holds two flags for
a given history page. Figure 21 shows the register format. The flags for a given history page are always spaced 8-bits
apart from one another. For example, history page 1 flags are always located at bit positions D0 and D8, history page 84
flags are at locations D3 and D11, etc. Note that the last flag register contains information for only 3 pages, in this case,
the upper 5-bits of each byte should be ignored.
www.maximintegrated.com
Maxim Integrated | 66
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
HISTORY PAGE N
HISTORY PAGE N
WRITE INDICATOR 2
WRITE INDICATOR 1
HISTORY PAGE N+7
WRITE INDICATOR 2
HISTORY PAGE N+1
WRITE INDICATOR 2
HISTORY PAGE N+7
WRITE INDICATOR 1
HISTORY PAGE N+1
WRITE INDICATOR 1
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
WRITE FLAG REGISTER FORMAT
HISTORY PAGE N
HISTORY PAGE N
VALID INDICATOR 2
VALID INDICATOR 1
HISTORY PAGE N+7
VALID INDICATOR 2
HISTORY PAGE N+1
VALID INDICATOR 2
HISTORY PAGE N+7
VALID INDICATOR 1
HISTORY PAGE N+1
VALID INDICATOR 1
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
VALID FLAG REGISTER FORMAT
Figure 21. Write Flag Register and Valid Flag Register Formats
Once all four flags for a given history page are known, the host can determine if the history page contains valid data. If
either write flag is set then data has been written to that page by the IC. If both write flags are clear, the page has not yet
been written. Due to application conditions, the write may not have been successful. Next check the valid flags. If either
valid flag is set, the data should be considered good. If both valid flags are clear then the data should be considered bad
and the host should ignore it. Table 10 shows how to decode the flags.
Table 10. Decoding History Page Flags
WRITE INDICATOR
1
WRITE INDICATOR
2
VALID INDICATOR
1
VALID INDICATOR
2
PAGE STATUS
Page empty.
0
1
0
X
0
X
0
Write failure. Page has invalid
data.
X
1
X
1
Write success. Page has valid
data.
X
Write failure. Page has invalid
data.
0
0
X
1
1
X
1
Write success. Page has valid
data.
X
www.maximintegrated.com
Maxim Integrated | 67
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Reading History Data
Once all pages of valid history data have been identified, they can be read from the IC using the HISTORY RECALL
command. Table 11 shows the command and history page relationship. After sending the command, wait t , then
RECALL
read the history data from IC page 1Fh. Each page of history data has the same format as page 1Ah. For example,
nCycles is found at address 1A4h and nCycles history are at 1F4h, nTimerH is located at address 1AFh and nTimerH
history is located at address 1FFh, etc.
Table 11. Reading History Data
COMMAND
E22Eh
E22Fh
...
HISTORY PAGE RECALLED TO PAGE 1EH
Page 1
Page 2
...
E291h
Page 100
History Data Reading Example
The host would like to read the life-logging data from a given IC. The host must first determine how many history pages
have been written and if there are any errors. To start checking history page 1, the host sends E29Ch to the command
register, wait t
, then read location 1F2h. If either the D0 or the D8 bit in the read data word is a logic 1, the host
RECALL
knows that history page 1 contains history data. The host can then check page 2 (bits D1 and D9) up to page 7 (bits D7
and D15). The host continues on to pages 8 to 16 by reading location 1F3h and then repeating individual bit testing. This
process is repeated for each command and address listed in Table 9 until the host finds a history page where both write
flags read logic 0. This is the first unwritten page. All previous pages contain data, all following pages are empty.
The host must now determine which, if any, of the history pages have bad data and must be ignored. The above process
is repeated for every location looking at the valid flags instead of the write flags. Any history page where both valid flags
read logic 0 is considered bad due to a write failure and that page should be ignored. Once the host has a complete list
of valid written history pages, commands E22Eh to E291h can be used to read the history information from page 1Fh for
processing.
Note that this example was simplified in order to describe the procedure. A more efficient method would be for the host
to send a history command once and then read all associated registers. For example, the host could send the E29Ch
command once and then read the entire memory space of 1F0h to 1FFh which would contain all write flags for pages 1
to 100 (1F2h to 1FEh) and all valid flags for pages 1 to 8 (1FFh). This applies for all E2XXh history commands.
See Appendix A: Reading History Data Pseudo-Code Example section for a psuedo-code example of reading history
data.
www.maximintegrated.com
Maxim Integrated | 68
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Analog Measurements
The IC monitors individual cell and pack voltages, current, and temperatures as shown in Table 12. This information is
used to protect the battery pack, provided to the fuel gauge algorithm to predict cell capacity and also made available to
the user. See the Analog Measurement Registers section for more details.
Table 12. Analog Measurement Registers
REGISTER NAME
ADDRESS
PURPOSE/CONTENTS
Voltage
Registers
VCell
01Ah
Lowest cell voltage
Cell1, Cell2,
Cell3, Cell4
0D8h,0D7h,
0D6h,0D5h
Direct cell measurements of selected number of cells
The Batt registers contains the total pack voltage measured inside the
protector and PCKP register contains the voltage between PACK+ and
GND
0DAh,
0DBh
Batt, PCKP
AvgVCell
019h
Average VCell
0D4h,
0D3h,
0D2h, 0D1h
AvgCell1, AvgCell2,
AvgCell3, AvgCell4
Average of voltages
Temperature
Registers
The highest thermistor temperature if enabled, and the die-temperature if
the thermistors are disabled
Temp
01Bh
13Ah,
139h,
138h, 137h
Temp1, Temp2,
Temp3, Temp4
Individual temperature measurements from the enabled thermistors and
internal die temperature
DieTemp
034h
AvgTA,
016h,
AvgTemp1,
AvgTemp2,
AvgTemp3, AvgTemp4
136h, 135h,
134h, 133h
Average of temperatures
040h
AvgDieTemp
Current
Current
Registers
01Ch
01Dh
Battery current
Average current
AvgCurrent
Other
Power, AvgPower
0B1h, 0B3h Power
0BEh,
TimerH, Timer
nTimerH
32-bit 23.9 year timer
03Eh
23.9 year nonvolatile timer
1AFh
QH, QL
04Dh, 04Eh 32-bit coulomb counter
www.maximintegrated.com
Maxim Integrated | 69
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Cell Balancing
If cells are imbalanced, then one cell might reach full or empty earlier than others, limiting the maximum capacity of the
pack. The IC balances the cells using internal MOSFETs. While charging, if the IC detects that the voltage of a cell or
cells is higher than the average voltage of the cell pack as determined by nBalTh.BALCFG setting, the IC enables an
internal FET to shunt current away from the corresponding cell. The small difference in charging current balances all cells
in the pack over time.
Cell Balancing Window of Operation
Cell balancing occurs when cell balancing is enabled and there is a voltage mismatch between the maximum and
minimum cell voltages greater than the balancing threshold and if either of the following conditions are met:
● The AvgCurrent register value must be above nProtMiscTh.CurrDet, which indicates the battery is charging.
● The Voltage Fuelgauge State of Charge (VFSOC) register value must be larger than the FullSOCThr register value
indicating the pack is nearly full.
Cell balancing continues after the charge has stopped and even into discharge as long as VFSOC remains above
FullSOCThr. This can extend the balancing opportunity beyond the typical charging window. Figure 22 shows the
opportunity of when cell balancing may occur.
CAREFUL BALANCING BY THE IC EXTENDS OPPORTUNITY
TIME BEYOND THE TYPICAL CHARGING WINDOW
BALANCING CONTINUES BEYOND CHARGE-STOP
AND INTO DISCHARGE UNTIL VFSOC < FULLSOCTHR
BALANCING
BLOCKED
UNTIL
CHARGING
CHARGING
0mA
DISCHARGING
END-OF-CHARGE
START-OF-LOAD
Figure 22. Cell Balancing Window of Operation
www.maximintegrated.com
Maxim Integrated | 70
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Cell Balancing Order and Thresholds
As soon as the cell balancing window is entered the maximum and minimum average cell voltages are calculated. If the
difference from max to min is more than the threshold defined by the nBalTh.BALCFG and nBalTh.RMismatch settings,
the corresponding internal balancing switch is enabled to reduce charging current flowing through the cell with the highest
voltage. Table 13 shows all balancing threshold levels determined by BALCFG. The recommended balancing threshold
is 011b or 10.0mV.
Table 13. Cell Balancing Thresholds
BALCFG VALUE
BALANCING THRESHOLD
000b
Balancing Disabled (Factory Default)
001b
2.5mV
5.0mV
010b
011b
10.0mV
20.0mV
40.0mV
80.0mV
160.0mV
100b
101b
110b
111b
RMismatch
The IC determines when there is a voltage mismatch by comparing the maximum and minimum cell voltages.
VOLTAGE = MaxCellVoltage - MinCellVoltage
MISMATCH
In order for balancing to occur, the voltage mismatch must be greater than a configurable threshold.
nBalTh.BalCfg
VOLTAGE
> 1.25mV x 2
+ |AverageCurrent| x Rmismatch
MISMATCH
Rmismatch is used for balancing to tolerate resistance mismatch between cells, which normally is larger at low states
of charge, and exclude balancing during higher current. Rmismatch should be selected in mΩ approximately 20% of
nominal battery resistance. Default recommendation is nBalTh.Rmismatch = 3 corresponding with 11.7mΩ.
Cell Balancing Circuits
Figure 23 shows the equivalent balancing circuits for 2S-, 3S-, and 4S-cell packs. Internal cell-balancing FETs allow
current to be drawn from an individual cell in the pack during charge. To limit current during cell balancing, an external
resistor must be added in series with the CELL1, CELL2, CELL3 and BATTS pins. If these resistors are not installed,
power in excess of the IC package maximum rating could be drawn leading to failure.
www.maximintegrated.com
Maxim Integrated | 71
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
RBAL4
BATTS
MAX17320
0.1µF
9Ω
RBAL3
CELL3
0.1µF
9Ω
RBAL2
CELL2
0.1µF
9Ω
RBAL1
CELL1
0.1µF
9Ω
GND
CSP
CSN
RSENSE
Figure 23. Cell Balancing Configuration
www.maximintegrated.com
Maxim Integrated | 72
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Cell Balancing Current
External series resistors on the CELL1, CELL2, CELL3 and BATTS pins are required to limit the current flow when
balancing. The value of these resistors should be selected to prevent exceeding 100mA, the maximum rated current for
these pins. The balancing currents can be calculated as follows. Remember to size these resistors to handle the power
dissipated by balancing.
CELL1:
IBAL
= V
/ (R
+ R
SWITCH
)
MAX
CELLMAX
BAL
CELL2, CELL3, BATTS:
Where:
IBAL
= V
/ (2 x R
+ R
)
SWITCH
MAX
CELLMAX
BAL
R
is 9Ω typical
SWITCH
V
is the maximum cell voltage during charging
CELLMAX
R
is the external series resistor to limit current
BAL
Cell Balancing Duty Cycle
The IC temporarily interrupts cell balancing to prevent interference with voltage and current measurements. Balancing is
disabled 45ms minimum prior to making a measurement to allow for settling of the external filter on the pin. This pause
occurs once every task period and has minimal impact on the average balancing current as shown in Figure 24.
45ms TYPICAL
SETTLING TIME
AND ADC
MEASUREMENTS
BALANCING
ACTIVE
BALANCING
ACTIVE
351ms TYPICAL
Figure 24. Cell Balancing Duty Cycle
Internal Self-Discharge Detection Interaction with Cell Balancing
Cell balancing is compatible with the IC's internal self-discharge detection function without any special user
considerations. The internal self-discharge algorithm uses the coulomb counter, which corresponds to the state of the
lowest state cell, so it is immune from the balancing of the cells with higher voltages.
www.maximintegrated.com
Maxim Integrated | 73
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Backup and Always-On LDO
The IC provides a configurable always-on LDO (1.8V or 3.4V) that can power small critical loads (less than 2mA). The
always-on LDO remains on during undervoltage protection events and permanent failure events as well as remains on
when the IC is in ship mode. To conserve power in deepship mode, the LDO is turned off.
Applications:
● Real-Time Clock
● Replace any coin cell
● Always-on security/tamper detection
● Payment terminals/mobile point-of-sale
The host can turn on/off the LDO as well as change the output voltage between 1.8V and 3.4V by writing the nPackCfg
register if the memory location is unlocked and the write protection is disabled.
SHA-256 Authentication
The IC supports authentication which is performed using a FIPS 180-4 compliant SHA-256 one-way hash algorithm on
a 512-bit message block. The message block consists of a 160-bit secret, a 160-bit challenge, and 192 bits of constant
data. Optionally, the 64-bit ROM ID replaces 64 of the 192 bits of constant data used in the hash operation. Contact
Maxim for details of the message block organization.
The host and the IC both calculate the result based on the mutually known secret. The result of the hash operation is
known as the message authentication code (MAC) or message digest. The MAC is returned by the IC for comparison
to the host’s MAC. Note that the secret is never transmitted on the bus and thus cannot be captured by observing bus
traffic. Each authentication attempt is initiated by the host system by writing a 160-bit random challenge into the SHA
memory address space 0C0h to 0C9h. The host then issues the compute MAC or compute MAC with ROM ID command.
The MAC is computed per FIPS 180-4 and stored in address space 0C0h to 0CFh overwriting the challenge value.
The IC introduces the new MAC key derivation function (MKDF), a 2-stage authentication scheme that utilizes an
intermediate secret for an added layer of security.
See the SHA-256 Authentication Procedures section for details of all of the SHA-256 procedures.
Note that the results of the authentication attempt are determined by host verification. The operation of the IC is not
affected by authentication success or failure.
www.maximintegrated.com
Maxim Integrated | 74
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Wake-Up/Shutdown
Modes of Operation
The MAX17320 supports five power modes (two active modes and three shutdown modes) as shown in Table 14 with
descriptions of the features available, the typical current consumption, and the method to enter and exit each mode.
Table 14. Modes of Operation
CONSUMPTION
MODE
DESCRIPTION
(TYPICAL)
38μA
Full functionality. The protection FETs, charge pump, and ADC are on. Firmware tasks execute
every 351ms.
Full Active
ADC is on. The FETs and charge pump are disabled due to a protection event, disconnecting
the battery from the system. RAM is preserved and the gauge continues to monitor the battery
until the fault is removed. Firmware remains awake and ready to communicate. Firmware tasks
execute every 1.4s.
Protect
16μA
Similar state as "Protect" except the firmware is responsive to wake-up events such as charger
connection, communications wake-up, or pushbutton wake-up (depending on which wake-ups
are enabled by configuration). Firmware tasks execute every 1.4s.
Ship*
16μA
2.2μA
2.2μA
FETs, charge pumps, ADC, and firmware are all placed into a shutdown state. The only activity
alive relates to analog circuits that monitor for wake-up conditions (charger detection,
communications, or pushbutton, depending on which are enabled).
DeepShip*
FETs, charge pumps, ADC, firmware, and most wake-up circuits are powered down. Only the
charger-detection wake-up circuit remains powered in this mode to best conserve the small
remaining battery capacity and prevent deep discharge.
Undervoltage
Shutdown
2
2
*On the I C shutdown command or when the I C SCL/SDA lines collapse (and depending on whether COMMSH is
enabled), the MAX17320 either enters Ship (if nProtCfg.DeepShpEn = 0) or DeepShip (if nProtCfg.DeepShpEn = 1).
The MAX17320 can be awoken with a variety of methods depending on the configuration. If pushbutton wake-up
is enabled (nConfig.PBen = 1), then consistently pulling the ALRT/PIO pin low, either by pushbutton or system
configuration, wakes up the device. A high-to-low transition on any of the communication lines wakes up the device. A
consistent connection to a charger wakes up the device.
The MAX17320 prevents accidental wake-up when the system is boxed and shipped. When awoken by any source, it
debounces all wake-up sources (button, communications, and charger detection) to ensure that the wake-up is valid. If
no valid wake-up is discovered, the device returns to Ship or DeepShip.
www.maximintegrated.com
Maxim Integrated | 75
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Power Mode Transition State Diagram
WAKEVERIFY: ANY OF THE FOLLOWING CONFIRM
LEGITIMATE WAKE-UP:
1) PUSHBUTTON CONSISTENTLY LOW (IF ENABLED)
2) ALRT PIN CONSISTENTLY LOW (IF ENABLED)
3) COMMUNICATIONS (HIGH+LOW DETECTED)
4) CHARGER CONSISTENTLY DETECTED
HW
STARTUP
POWER
GOOD
STARTUP
WAKEVERIFY
WAKE-UP VERIFIED
ACTIVE
(38µA)
IF (FETS OFF)
PROTECT
(16µA)
EITHER
FET ON
SHIP
(16µA)
ANY SHUTDOWN
CONDITION > TMR/2
0
NPROTCFG.DEEPSHIPEN
SHDN
COMMITTED
FETS OFF,
PKSINK = 1
1
DEEPSHIP
(2.2µA)
TIMER &
PCKPOK
SHUTDOWN CONDITIONS:
COMMAND, COMMS-DROP, OR UV
SHDNTIMER COUNTS UPON CONDITION, ABORTS (CLEARS)
UPON ABSENSE OF CONDITIONS. AT HALF TIMER, THE
TIMER PAUSES UNLESS CHARGER IS CLEARLY ABSENT
(PCKPOK = 0)
Figure 25. Power Modes Transition State Diagram
Pushbutton Wake-Up
The ALRT/PIO pin can be used to wake up the device by enabling the pushbutton wake-up function by setting the
nConfig.PBen. The pushbutton can be implemented in the system to wake up the device and the system as shown in the
Pushbutton Schematic.
www.maximintegrated.com
Maxim Integrated | 76
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Register Description
Register Description Conventions
The following sections define standard conventions used throughout the data sheet to describe register functions and
device behavior. Any register that does not match one of the following data formats is described as a special register.
Standard Register Formats
Unless otherwise stated during a given register's description, all IC registers follow the same format depending on the
type of register. Refer to Table 15 for the resolution and range of any register described hereafter. Note that current and
capacity values are displayed as a voltage and must be divided by the sense resistor to determine amps or amp-hours. It
is strongly recommended to use the nRSense (1CFh) register to store the sense resistor value for use by host software.
Table 15. ModelGauge Register Standard Resolutions
REGISTER
TYPE
MINIMUM
VALUE
MAXIMUM
VALUE
LSB SIZE
NOTES
5.0μVh/
327.675mVh/
R
SENSE
Capacity
0.0μVh
Equivalent to 1.0mAh with a 0.005Ω sense resistor.
1% LSb when reading only the upper byte.
R
SENSE
Percentage
Voltage
1/256%
0.078125mV
1.5625μV/
0.0%
0.0V
255.9961%
5.11992V
-51.2mV/
51.1984mV/
R
SENSE
Signed 2's complement format. Equivalent to 312.5μA with a
0.005Ω sense resistor.
Current
R
R
SENSE
SENSE
Signed 2's complement format. 1°C LSb when reading only the
upper byte.
Temperature
1/256°C
-128.0°C
127.996°C
Resistance
Time
1/4096Ω
5.625s
0.0Ω
0.0s
15.99976Ω
102.3984hr
Special
Format details are included with the register description.
Device Reset
Device reset refers to any condition that would cause the IC to recall nonvolatile memory into RAM locations and restart
operation of the fuel gauge. Device reset refers to the initial power-up of the IC, temporary power loss, or reset through
the software power-on-reset command.
Nonvolatile Backup and Initial Value
All configuration register locations have nonvolatile memory backup that can be enabled with control bits in the nNVCfg0,
nNVCfg1, and nNVCfg2 registers. If enabled, these registers are initialized to their corresponding nonvolatile register
value after device reset. If the nonvolatile backup is disabled, the register restores to an alternate initial value instead.
See each register description for details.
Register Naming Conventions
Register addresses are described throughout the document as 9-bit internal values from 000h to 1FFh. These addresses
2
must be translated to 16-bit external values for the 1-Wire version or 8-bit values for the I C version. See the Memory
section for details.
Register names that start with a lowercase 'n', such as nPackCfg for example, indicate the register is a nonvolatile
memory location. Register names that start with a lowercase 's' indicate the register is part of the SBS compliant register
block.
www.maximintegrated.com
Maxim Integrated | 77
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Protection Registers
nPackCfg Register (1B5h)
Configure nPackCfg register according to the application schematic.
Register Type: Special
Factory Default Value: 0004h
The nPackCfg register configures the number of cells and thermistors (and thermistor type) in the battery pack. It also
configures the charge pump and backup regulator voltage levels. nPackCfg configuration must match the pack hardware
for the proper operation of the IC. See the Typical Application Circuits section for recommended nPackCfg settings based
on operating circuit configuration. Table 16 shows the register format.
Table 16. nPackCfg (1B5h) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
AOCfg
BtPkEn
0
THType
0
CPCfg
0
0
0
NThrms
NCELLS
0: Always write 0
NCELLS: Number of Cells. This field configures the IC for the number of cells in series in the cell pack. Set NCELLS =
cellcount-2.
NThrms: Number of Thermistor Channels. 000b: only die temp, 001b: die temp and 1 thermistor channel enabled, 010b:
die temp and 2 thermistor channels enabled, 011b: die temp and 3 thermistor channels enabled, 100b: die temp and 4
thermistor channels enabled etc.
THType: If using 10kΩ NTC thermistor, set THType = 0. If using 100kΩ NTC thermistor, set THType = 1.
CPCfg: Charge Pump Voltage Configuration. Set according to the desired gate drive. Note that there is a trade-off in
quiescent vs. gate-drive. Set CPCfg = {00b,01b,10b} for {6V, 8V, 10V} settings.
AOCfg: Always-on Regulator Configuration.
AOCfg VALUE
DESCRIPTION
00b
01b
10b
11b
AOLDO is disabled.
AOLDO is enabled. Output is 3.4V.
AOLDO is enabled. Output is 1.8V.
AOLDO is enabled. Output is 3.4V.
BtPkEn: Enable Pckp and Batt Channels update. If set to 0 Pckp/Batt channels updates every 22.4s. If set to 1 Pckp/
Batt channels update after all cell measurements are completed.
www.maximintegrated.com
Maxim Integrated | 78
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Voltage Protection Registers
nUVPrtTh Register (1D0h)
Factory Default Value: 508Ch
The nUVPrtTh register shown in Table 17 sets undervoltage protection, deep-discharge-state protection, and
undervoltage-shutdown thresholds.
Table 17. nUVPrtTh Register (1D0h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
UVP
0
UOCVP
UVShdn
UVP: UnderVoltage Protection threshold. The IC opens the discharge FET when VCell < UVP. UVP can be configured
from 2.2V to 3.46V in 20mV steps. UVP is unsigned.
UOCVP: Under Open Circuit Voltage Protection Threshold (also refered to as SmartEmpty). The IC opens the discharge
FET when VFOCV < UOCVP. UOCVP is relative to UVP and can be configured from UVP to UVP + 1.28V in 40mV
steps. UOCVP is unsigned.
UVShdn: UnderVoltage Shutdown Threshold. The IC shutdowns when VCell < UVShdn. UVShdn is relative to UVP and
can be configured from UVP - 0.32V to UVP + 0.28V in 40mV steps.
nJEITAV Register (1D9h)
Factory Default Value: 0059h
The nJEITAV register, shown in Table 18, sets the JEITA Charge Voltage configuration for the IC. The JEITA charge
voltage can be read from a charger to set the appropriate charge voltage based on the temperature. Also, this value is
used to determine the overvoltage-protection threshold.
Each charge voltage register is an offset with a 5 or 20mV resolution. The RoomChargeV offset is defined relative to
a normal standard charge setting of 4.2V. The additional charge voltages are relative to RoomChargeV based on the
temperature. To disable the temperature dependence and create a flat charging voltage across the temperature range,
set dWarmChargeV, dColdChargeV, and dHotChargeV to a value of 00b.
Table 18. nJEITAV Register (1D9h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RoomChargeV
dWarmChargeV
dColdChargeV
dHotChargeV
RoomChargeV: RoomChargeV defines the charge voltage between temperatures T2 "Cold" and T3 "Warm", relative to
a standard 4.2V setting, providing a range of 3.56V to 4.835V in 5mV steps. RoomChargeV is a signed configuration. Set
to 00h to configure for standard 4.2V.
dColdChargeV: ColdChargeV defines the delta charge voltage (relative to RoomChargeV) between temperatures T1
and T2, relative to the room setting, providing a range of RoomChargeV to (RoomChargeV-140mV) in -20mV steps.
dColdChargeV configuration is unsigned.
dWarmChargeV: WarmChargeV defines the delta charge voltage (relative to RoomChargeV) between temperatures
TWarm and T3, relative to the room setting, providing a range of RoomChargeV to (RoomChargeV-60mV) in -20mV
steps. dWarmChargeV configuration is unsigned.
dHotChargeV: HotChargeV defines the delta charge voltage (relative to WarmChargeV) between temperatures T3
and T4, relative to the room setting, providing a range of WarmChargeV to (WarmChargeV-140mV) in -20mV steps.
dHotChargeV configuration is unsigned.
www.maximintegrated.com
Maxim Integrated | 79
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
nOVPrtTh Register (1DAh)
Factory Default Value: B754h
The nOVPrtTh register shown in Table 19 sets the permanent overvoltage protection threshold, the charge-detection
threshold, the overvoltage-protection threshold, and the overvoltage-protection-release threshold. dOVP and dOVPR are
relative to the Charge Voltage that is set in the nJEITAV register and have a 10mV resolution.
Table 19. nOVPrtTh Register (1DAh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
OVPPermFail
ChgDetTh
dOVP
dOVPR
dOVP: Delta from ChargeVoltage to Overvoltage Protection. dOVP sets JEITA overvoltage protection relative to
ChargeVoltage (see nJEITAV). If nNVCfg1.enJP is disabled, then OVP voltage is calculated from RoomChargeV across
all temperature zones. This is a positive number with 10mV resolution and 150mV range. Overvoltage protection is
calculated as:
OVP = ChargeVoltage + dOVP x 10mV
dOVPR: Delta from Overvoltage Protection to the Overvoltage-Release Threshold. dOVPR sets overvoltage-protection
release relative to the overvoltage-protection setting. This is a positive number with 10mV resolution and is translated to
a negative offset relative to OVP. Overvoltage-protection release is calculated as:
OVPR = OVP - dOVPR x 10mV
OVPPermFail: Permanent Failure OVP (permanent overvoltage protection) Threshold. Permanent failure overvoltage
protection occurs when any cell voltage register reading exceeds this value. The OVPPermFail range is
OVP_threshold
+ 40mV to OVP_threshold
+ 340mV with a 20 mV lsb.
Room
Room
OVP_PermFail_Threshold = OVP
+ 40mV + (OVPPermFail x 20mV)
Room
ChgDetTh: Charger Detection Threshold. The IC determines that a charger is connected when PCKP > (BATT +
ChgDetTh). ChgDetTh has a range of 10mV to 80mV with a 10mV lsb.
nBalTh Register (1D4h)
Factory Default Value: 0000h
The nBalCfg register shown in Table 20 sets the balancing and imbalance settings and thresholds.
Table 20. nBalTh Register (1D4h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
Zener
BALCFG
Rmismatch
Imbalance
0: Set 0, do not set 1.
Zener: Zener Balancing Enable. Set to 1 to enable the Zener Balancing functionality. Set to 0 to disable the Zener
Balancing. When Zener Balancing is enabled, the IC acts as if a Zener diode is placed in parallel with each cell. The
reverse breakdown voltage of the virtual Zener diode is the ChargingVoltage register. Whenever nBalTh.Zener = 1, the
IC actively discharges the highest voltage cell with a voltage higher than the ChargingVoltage register.
BALCFG: Balancing Configuration. This field sets the cell balancing voltage threshold. When set to 0, cell balancing is
disabled. When BALCFG bits are set to any nonzero value, cell balancing begins when inside the cell balancing window
as shown in Figure 22. See RMismatch section for details.
Rmismatch: Rmismatch is set according to the following equation:
nBalTh.Rmismatch = 32 x Rmismatch(mΩ)/125mΩ (maximum settable Rmismatch is 121mΩ)
Choose Rmismatch in mΩ approximately 20% of nominal battery resistance. The default recommendation is
nBalTh.Rmismatch = 3 corresponding with 11.7mΩ. See the RMismatch section for details.
www.maximintegrated.com
Maxim Integrated | 80
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Imbalance: Cell Imbalance Protection Threshold. Set the amount of cell imbalance that creates a charge protection fault.
Set Imbalance to 0 to disable cell imbalance protection. The LSB size is 10mV.
Current Protection Registers
nODSCTh Register (1DDh)
Factory Default Value: 0EAFh
The nODSCTh register sets the current thresholds for each overcurrent alert. The format of the registers is shown in
Table 21.
Table 21. nODSCTh Register (1DDh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
OCTH
SCTH
ODTH
X: Don't Care.
SCTH: Short-Circuit Threshold Setting. Sets the short-circuit threshold to a value between 0mV and -155mV with a step
size of -5mV. The SCTH bits are stored such that 1Fh = 0mV and 00h = -155mV. Short-circuit threshold is calculated as
-155mV + (SCTH x 5mV)).
ODTH: Overdischarge Threshold Setting. Sets the overdischarge threshold to a value between 0mV and -77.5mV with
a step size of -2.5mV. The ODTH bits are stored such that 1Fh = 0mV and 00h = -77.5mV. Overdischarge threshold is
calculated as -77.5mV + (ODTH x 2.5mV)).
OCTH: Overcharge Threshold Setting. Sets the overcharge threshold to a value between 0mV and 38.75mV with a step
size of 1.25mV. The OCTH bits are stored such that 1Fh = 0mV and 00h = 38.75mV. Overcharge threshold is calculated
as 38.75mV - (OCTH x 1.25mV)).
Table 22 shows sample values of calculated mV thresholds for OCTH, SCTh, and ODTH. Equivalent current thresholds
are shown assuming a 5mΩ sense resistor.
Table 22. OCTH, SCTh, and ODTH Sample Values
OCTH
SCTH
ODTH
00h
01h
02h
04h
08h
10h
14h
18h
1Eh
1Fh
38.75mV
37.50mV
36.25mV
33.75mV
28.75mV
18.75mV
13.75mV
8.75mV
7.75A
7.50A
7.25A
6.75A
5.75A
3.75A
2.75A
1.75A
0.25A
0.000A
-155mV
-150mV
-145mV
-135mV
-115mV
-75mV
-55mV
-35mV
-5mV
-31.00A
-30.00A
-29.00A
-27.00A
-23.00A
-15.00A
-11.00A
-7.00A
-77.5mV
-75.0mV
-72.5mV
-67.5mV
-57.5mV
-37.5mV
-27.5mV
-17.5mV
-2.5mV
-15.50A
-15.00A
-14.50A
-13.50A
-11.50A
-7.50A
-5.50A
-3.50A
-0.50A
0.00A
1.25mV
-1.00A
0.00mV
0mV
0.00A
0.0mV
www.maximintegrated.com
Maxim Integrated | 81
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
nODSCCfg Register (1DEh)
Factory Default Value: 4355h
The nODSCCfg register configures the delay behavior for the short-circuit, overdischarge-current, and overcharge-
current comparators. The format of the register is shown in Table 23.
Table 23. nODSCCfg Register (1DEh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
1
X
X
SCDLY
X
1
X
1
OCDLY
X: Don't Care.
SCDLY: Short-Circuit Delay. Configure from 0h to Fh to set short circuit detection debouncing delay between 70μs and
985μs (70μs + 61μs x SCDLY). There may be up to 31μs of additional delay before the short-circuit's alert affects the
discharge FET.
OCDLY: Overdischarge and Overcharge Current Delay. Configure from 1h to Fh to set overdischarge/overcharge
detection debouncing delay between 70μs and 14.66ms (70μs + 977μs x OCDLY).
nIPrtTh1 Register (1D3h)
Factory Default Value: 4BB5h
The nIPrtTh1 register shown in Table 24 sets upper and lower limits for overcurrent protection when current exceeds
the configuration threshold. The upper 8-bits set the overcharge current-protection threshold and the lower 8-bits set the
overdischarge current-protection threshold. Protection threshold limits are configurable with 400μV resolution over the
full operating range of the current register.
Table 24. nIPrtTh1 Register (1D3h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
OCCP
ODCP
OCCP: Overcharge Current-Protection Threshold at Room Temperature. Overcharge current-protection occurs when the
current register reading exceeds this value. This field is signed 2's complement with 400μV LSb resolution to match the
upper byte of the current register. HotCOEF, WarmCOEF, and ColdCOEF re-scales nIPrtTh1.OCCP in hot, warm, and
cold zone.
For example, in warm zone, overcharge current-protection threshold updates to OCCP x WarmCOEF.
See the nJEITAC register for HotCOEF, WarmCOEF, and ColdCOEF definitions and the nTPrtTh2 and nTPrtTh3
registers for temperature zone definitions.
ODCP: Overdischarge Current-Protection Threshold. Overdischarge current-protection occurs when current register
reading exceeds this value. This field is signed 2's complement with 400μV LSb resolution to match the upper byte of the
current register.
The fault delay for OCCP and ODCP is configured in nDelayCfg.OverCurrTimer.
nJEITAC Register (1D8h)
Factory Default Value: 644Bh
The nJEITAC register shown in Table 25 sets the nominal room temperature charging current and the coefficients to
scale the charging current across the temperature zones shown in Figure 3. The WarmCOEF, ColdCOEF, and HotCOEF
coefficients impact the charging current as well as OCCP and ODCP (See nIPrtTh1).
To disable the temperature dependence and create a flat charging current across the temperature range, set the lower
byte of nJEITAC to a value of FFh.
www.maximintegrated.com
Maxim Integrated | 82
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 25. nJEITAC Register (1D8h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RoomChargingCurrent
WarmCOEF
ColdCOEF
HotCOEF
RoomChargingCurrent: Sets the nominal room-temperature charging current. The LSB is 200μV. This value is
unsigned with a range of 00h (0mV) to FFh (51.2mV).
HotCOEF: Coefficient 12.5% to 100% relative to ChargingCurrent for controlling the charge current at hot. HotCOEF
has a 12.5% LSB resolution. The resulting HotChargingCurrent is controlled by the following equation:
HotChargingCurrent = RoomChargingCurrent x (HotCOEF+1)/8
WarmCOEF: Coefficient 62.5% to 100% relative to ChargingCurrent for controlling the charge current at warm.
WarmCOEF has a 12.5% LSB resolution. The resulting WarmChargingCurrent is controlled by the following equation:
WarmChargingCurrent = RoomChargingCurrent x (WarmCOEF+5)/8
ColdCOEF: Coefficient 12.5% to 100% relative to ChargingCurrent for controlling the charge current at cold. ColdCOEF
has a 12.5% LSB resolution. The resulting ColdChargingCurrent is controlled by the following equation:
ColdChargingCurrent = RoomChargingCurrent x (ColdCOEF+1)/8
HotCOEF, WarmCOEF, and ColdCOEF also rescale nIPrtTh1.OCCP.
Temperature Protection Registers
The IC has five thresholds for charging protection as well as overdischarge temperature protection and overtemperature
permanent failure protection. The standard register format for each of these thresholds is a signed 2's compliment
number with 1°C resolution. The IC has 2°C of hysterisis for releasing temperature faults.
nTPrtTh1 Register (1D1h)
Factory Default Value: 3700h
The nTPrtTh1 register shown in Table 26 sets T1 "Too-Cold" and T4 "Too-Hot" thresholds which control JEITA and
provide charging (Too-Hot or Too-Cold) protection. nProtMiscTh.TooHotDischarge provides discharging (Too-Hot only)
protection.
Table 26. nTPrtTh1 Register (1D1h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
T4 ("Too-Hot")
T1 ("Too-Cold")
T1-T4 follow JEITA's naming convention for temperature ranges.
T1: JEITA "Too-Cold" temperature threshold. When Temp < T1, charging is considered unsafe and unhealthy, and the
IC blocks charging.
T4: JEITA "Too-Hot" temperature threshold. When Temp > T4, charging is blocked by the IC.
nTPrtTh2 Register (1D5h)
Factory Default Value: 2D0Ah
The nTPrtTh2 register shown in Table 27 sets T2 "Cold" and T3 "Hot" thresholds which control JEITA and modulate
charging (Hot or Cold) guidance and protection.
Table 27. nTPrtTh2 (1D5h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
T3 ("Hot")
T2 ("Cold")
T1-T4 follow JEITA's naming convention for temperature ranges.
www.maximintegrated.com
Maxim Integrated | 83
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
T2: JEITA "Cold" temperature threshold. When Temp < T2, charging current/voltage should be reduced, and the charge-
protection thresholds are adjusted accordingly.
T3: JEITA "Hot" temperature threshold. When Temp > T3, charging current/voltage should be reduced and the charge-
protection thresholds are adjusted accordingly.
nTPrtTh3 Register (1D2h) (beyond JEITA)
Factory Default Value: 5528h
The nTPrtTh3 register shown in Table 28 sets Twarm and TpermFailHot thresholds which control JEITA and modulate
charging (Warm) guidance and protection.
Table 28. nTPrtTh3 Register (1D2h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
TpermFailHot
Twarm
nTPrtTh3 defines protection thresholds beyond standard JEITA definition.
Twarm: Warm temperature threshold (between 'normal' and THot), giving an extra temperature region for changing
charging current and charging voltage control.
TpermFailHot: If enabled, the IC goes into permanent failure mode, and permanently disables the charge FET as well
as trips the secondary protector (if installed) or blows the fuse (if installed).
nProtMiscTh Register (1D6h)
Factory Default Value: 7A28h
The nProtMiscTh register is shown in Table 29 and sets a few miscellaneous protection thresholds.
Table 29. nProtMiscTh Register (1D6h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
QovflwTh
TooHotDischarge
CurrDet
DieTempTh
DieTempTh: Sets the Dietemp Overtemperature-Protection Threshold. DieTempTh is used as a proxy for FET
temperature and controls the FET overtemperature fault. The range is 50°C and 125°C with a 5°C LSB.
CurrDet: CurrDet is configurable from 25μV/R
to 400μV/R
in 25μV/R
steps (equivalent to 5mA to
SENSE
SENSE
SENSE
80mA in 5mA steps with a 5mΩ sense resistor). It is a threshold to detect discharging and charging events. If current >
CurrDet then charging; if current < -CurrDet then discharging.
CurrDet Threshold = (CurrDet + 1) x 5mA (i.e., 0 = 5mA for 5mΩ R
)
SENSE
TooHotDischarge: Sets the Overtemperature-Protection Threshold Associated with Discharge. TooHotDischarge has
2°C LSB's and defines the delta between Over-Temp-Charge (nTPrtTh1.T4) and Over-Temp-Discharge. The range is
nTPrtTh1.T4(TooHot) to nTPrtTh1.T4(TooHot) + 30°C.
QovflwTh: Capacity Overflow Threshold. QovflwTh sets the coefficient for the capacity overflow-protection threshold.
Capacity overflow protection threshold = designCap x coefficient. The IC monitors the delta coulomb count (deltaQ)
between the coulomb count at the start-of-charge and the present coulomb count. If the delta Q exceeds the capacity
overflow-protection threshold, indicating that the charger has charged more than the expected capacity of the battery,
then a ProtStatus.Qovrflw fault is generated. The coefficient is calculated as: coefficient = 1.0625 + (QovflwTh x 0.0625).
www.maximintegrated.com
Maxim Integrated | 84
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Fault Timer Registers
nDelayCfg Register (1DCh)
Factory Default Value: AB3Dh
Set nDelayCfg to configure debounce timers for various protection faults. A fault state is concluded only if the condition
persists throughout the duration of the timer.
Table 30. nDelayCfg (1DCh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CHGWDT
FullTimer
OVPTimer
OverCurrTimer
PermFailTimer
TempTimer
UVPTimer
UVPTimer: Set UVPTimer to configure the Undervoltage-Protection timer.
Shutdown Timer: Set UVPTimer to configure the Shutdown timer.
Table 31. UVPTimer Settings
UVPTIMER SETTING
UVPTimer Configuration
Shutdown Timer Configuration
0
1
2
3
0 to 351ms
22.5s to 45s
2.8s to 5.625s
45s to 90s
5.625s to 11.25s
90s to 180s
11.25s to 22.5s
3min to 6min
TempTimer: Set TempTimer to configure the fault-timing for the following faults: Too-Cold-Charging (TooColdC), Too-
Hot-Charging (TooHotC), Die-Hot (DieHot), and Too-Hot-Discharging (TooHotD).
The TempTimer setting also controls the temperature transition delay. If the IC detects a change in temperature zone
that results in the OVP level being reduced to a lower level due to the JEITA configuration. There is a delay equal to the
TempTrans Configuration before the new lower OVP threshold goes into effect.
Table 32. TempTimer/TempTrans Setting
TEMPTIMER SETTING
0
1
2
3
Debounce 1
thermistor
Debounce up to 2
thermistors
Debounce up to 4
thermistors
Application
No debouncing
TempTimer
Configuration
0 to 351ms
1.4s to 2.8s
2.8s to 5.625s
5.625s to 11.25s
TempTrans
Configuration
3.151s to
4.55s
5.951s to 8.75s
11.55s to 17.15s
23.351s to 34.851s
PermFailTimer: Set PermFailTimer to configure the fault-timing for permanent failure detection. PermFailTimer must be
set to 3 for permanent failure detection to function properly.
Table 33. PermFailTimer Settings
PERMFAILTIMER SETTING
0 (NOT RECOMMENDED)
1
2
3
Configuration
0 to 351ms
351ms to 0.7s
0.7s to 1.4s
1.4s to 2.8s
OverCurrTimer: OverCurrTimer configures the fault timing for the slow overcharge-current detection (OCCP) as well as
overdischarge-current detection (ODCP). The additional fast hardware protection thresholds are described in nODSCCfg
and nODSCTh.
Table 34. OverCurrTimer Settings
OVERCURRTIMER
0
1
2
3
4
5
6
7
SETTING
Configuration
0.351s to
0.7s
0.7s to
1.4s
1.4s to
2.8s
2.8s to
5.6s
5.6s to
11.25s
11.25s to
22.5s
22.5s to
45s
0-351ms
www.maximintegrated.com
Maxim Integrated | 85
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
OVPTimer: Set OVPTimer to configure the fault timing for Overvoltage-Protection.
Imbalance Timer: Set OVPTimer to configure the Imbalance fault timer.
Table 35. OVPTimer Settings
OVPTIMER/IMBALANCE SETTING
0
1
2
3
OVPTimer Configuration
0 to 351ms
0 to 351ms
2.8s to 5.625s
2.8s to 5.625s
5.625s to 11.25s
5.625s to 11.25s
11.25s to 22.5s
11.25s to 22.5s
Imbalance Timer Configuration
FullTimer: Set FullTimer to configure the timing for full-detection. When charge-termination conditions are detected and
after the timeout, the CHG FET turns off (if feature is enabled).
Prequal Timer: Set FullTimer to configure the timing for prequal charging. Prequal Timer and FullTimer share the same
bits in the nDelayCfg register.
Table 36. FullTimer/Prequal Settings
FULLTIMER
SETTING
0
1
2
3
4
5
6
7
FullTimer
Configuration
67s to
90s
2.25min to
3min
4.5min to
6min
9min to
12min
18min to
24min
36min to
48min
72min to
96min
33s to 44s
18min
to
24min
36min
to
48min
Prequal Timer
Configuration
16.875s to
22.5s
33s to
44s
2.25min to
3min
4.5min to
6min
9min to
12min
67s to 90s
CHGWDT: Set CHGWDT to configure the charger communication watchdog timer. If enabled, the IC charge-protects
whenever the host has stopped communicating longer than this timeout.
Table 37. ChgWDT Settings
CHGWDT SETTING
0
1
2
3
Configuration
11.2s to 22.5s
22.5s to 45s
45s to 90s
90s to 3min
Battery Internal Self-Discharge Detection Registers
Factory Default nProtCfg2 Value: A065h
Factory Default nTCurve Value: 0000h
To enable the ISD feature using the coulombic-efficiency (CE) method, configure LeakFaultCfg, LeakCurrTh, and CEEn
as shown in Table 38 and Table 39. Choose the alert and fault mode with LeakFaultCfg and configure the thresholds
with LeakCurrTh, as shown in Table 40. When the ISD alerts are enabled, any leakage current detected beyond the
threshold is indicated by the ProtAlrt.LDET bit and Status.PA bit (if nConfig.ProtAlrtEn = 1). If the ALRT pin is enabled for
alerts (nConfig.Aen = 1 and nConfig.ProtAlrtEn = 1), then the pin indicates the ISD alert. To service the alert, first clear
the ProtAlrt register and then clear Status.PA. The event is also indicated in nBattStatus.LDET, which is recorded in the
permanent lifelog.
The reported leakage-current measurement can be read from two different different registers:
● LeakCurrRep = 15-bit unsigned left-justified value with an LSB of 1.5625μV/16 (or 0.3125mA/16 with 5mΩ sense
resistor)
● nBattStatus.LeakCurr = 8-bit unsigned value with an LSB of 3.125μV (or 0.625mA with 5mΩ sense resistor)
Contact Maxim for configuring the ISD feature.
Table 38. nProtCfg2 Register (1DFh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
1
0
CEEn
0
LeakCurrTh
CheckSum
www.maximintegrated.com
Maxim Integrated | 86
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 39. nTCurve Register (0x1C9) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
X
X
X
X
X
X
LeakFaultCfg
Table 40. Alert and Fault Mode Settings
LEAKFAULTCFG
DESCRIPTION
LEAKCURRTH RESOLUTION
ALERT RANGE
FAULT RANGE
SETTING
Note: Leakage current above LeakCurrTh triggers an alert/fault. Currents refer to
the 5mΩ R
SENSE
000
001
010
Disabled
Alert only
Fault = Alert + 5mA
0.625mA
to 10mA
5.625mA to 15mA
10.625mA to 20mA
0.625mA
Fault = Alert +
10mA
011
100
Fault Only (+5mA
offset)
6.25mA to 25mA
101
110
Alert Only
1.25mA
Fault = Alert + 5mA
1.25mA
to 20mA
6.25mA to 25mA
21.25mA to 40mA
Fault = Alert +
20mA
111
X: Don't Care
CEEn: Coulombic-efficiency (CE) method enable. Set to 1 to enable self-discharge detection
LeakFaultCfg: Leakage Fault Configuration. Set LeakFaultCfg to configure the alert and fault behavior as shown in Table
40.
LeakCurrTh: Leakage Current Threshold is an unsigned 4-bit threshold for leakage current alert and fault generation.
The LSB resolution is either 0.625mA or 1.25mA based on the LeakCurrCfg setting as shown in Table 40. When alerts
and faults are both enabled, the fault threshold is either 5mA, 10mA or 20mA above the alert threshold as shown in the
Description column of Table 40.
CheckSum: Protector NVM CheckSum. CheckSum is the checksum value of the protection registers for validating NVM
at startup when nNVCfg1.enProtChksm = 1.
LeakCurrRep Register (0x16F)
The LeakCurrRep register contains the reported leak current when it is enabled with nProtCfg2.F2FEn as shown in Table
41.
Table 41. LeakCurrRep Register (0x16F) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
Reported LeakCurrent
Reported LeakCurrent: Reported Leak Current is an unsigned 15-bit leakage current. This register stores the reported
leakage current with an LSB of 1.5625μV/16 (or 0.3125mA/16 with a 5mΩ sense resistor). The range is 0mA to
639.98mA.
www.maximintegrated.com
Maxim Integrated | 87
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Status/Configuration Protection Registers
The following registers configure and report various protection and alert statuses as measured by the IC.
nProtCfg Register (1D7h)
Factory Default Value: 0900h
The Protection Configuration register contains enable bits for various protection functions.
Table 42. nProtCfg Register (1D7h) Format
D15
D14
D13
D12
D4
D11
D10
D9
D8
ChgWDTEn
FullEn
SCTest
CmOvrdEn
0
PreqEn
D7
D6
D5
D3
D2
D1
D0
Reserved
PFEn
DeepShpEn
OvrdEn
UVRdy
FetPFEn
Reserved
Reserved
PFEn: PermFail Enable. Set PFEn = 1 to enable the detection of a Permanent Failure to permanently turn the FETs off.
All types of permanent failures operate only if PFEn = 1 and are all disabled if PFEn = 0. PFEn must be enabled for the
PFAIL pin to be operational. See the Permanent Fail section for more details.
FetPFEn: FET PermFail Enable. Set to 1 to enable Charge FET and Discharge FET open or short failure detection,
which registers a permanent failure and permanently turn the FETs off and drive the PFAIL pin high. PFEn must also be
set for the FET PermFail Enable to operate.
UVRdy: Undervoltage-Ready. In the undervoltage-protected state (but higher than undervoltage shutdown), this bit
chooses whether or not the CHG FET remains enabled. Configure UVRdy = 0 to keep the CHG FET and corresponding
pumps powered during undervoltage protection. In this state, the pack is quickly responsive to charger connection, but
the quiescent consumption remains 38μA. Configure UVRdy = 1 to disable the CHG FET and corresponding charge
pumps during undervoltage protection. In this state, the consumption drops to 16μA, but there may be hibernate latency
between when the charger is applied and the battery begins charging.
OvrdEn: Override Enable. Set OvrdEn = 1 to enable the Alert pin to be an input to turn disable the protection FETs. See
2
the Disabling FETs by Pin-Control or I C Command for more details.
CmOvrdEn: Comm Override Enable. This bit when set to 1, allows the ChgOff and DisOff bits in CommStat to be set
2
2
by I C/1Wire communication to turn off the protection FETs. See the Disabling FETs by Pin-Control or I C Command for
more details.
2
DeepShpEn: Deepship Enable. Set DeepShpEn = 1 to associate shutdown actions (I C shutdown command or
communication removal) with 2.2μA shutdown. All registers power down in this mode. Set DeepShpEn = 0 to continue
full calculations but with protector disabled (CHGEn = 0, DISEn = 0, pump off), operating at 6μA consumption.
PreqEn: PreQual Enable. Set PreqEn = 1 to enable the Pre-Qual enable functionality.
SCTest: Set SCTest = 01b to source 30μA from BATT to PCKP for testing the presence/removal of any overload/short-
circuit at PCKP. SCTest is only used during special circumstances when DIS = off. Particularly if an overdischarge current
fault has been tripped. The IC sets SCTest to push 30μA into PCKP. If PCKP rises above the 1.5V SCDet threshold, then
the overload is considered "removed" and safe to reconnect the DIS FET. Because of this, the PCKP resistor must be
10kΩ or less for proper short-circuit removal detection. Set SCTest = 00b to disable.
FullEn: Full Charge Protection Enable. Set FullEn = 1 to enable the full charge protection feature where the charge
FET opens when the battery is fully charged (RepSOC reaches 100%) plus a programmable delay that is configured in
nDelayCfg.FullTimer.
ChgWDEn: Charger WatchDog Enable. If the charger watchdog feature is enabled, the protector disallows charging
unless communication has not been detected for more than the Charger WatchDog delay that is configured in
nDelayCfg.ChgWdg.
www.maximintegrated.com
Maxim Integrated | 88
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Status Register (000h)
Register Type: Special
Nonvolatile Backup: None
Initial Value: 0x0002
The Status register maintains all flags related to alert thresholds and battery insertion or removal. Table 43 shows the
Status register format.
Table 43. Status Register (000h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
PA
Smx
Tmx
Vmx
X
Smn
Tmn
Vmn
dSOCi
Imx
X
X
X
Imn
POR
X
POR: Power-On Reset. This bit is set to a 1 when the device detects that a software or hardware POR event has
occurred. This bit must be cleared by system software to detect the next POR event. POR is set to 1 at power-up.
Imn: Minimum Current Alert Threshold Exceeded. This bit is set to a 1 whenever a Current register reading is below the
minimum IAlrtTh value. This bit is cleared automatically when Current rises above minimum IAlrtTh value. Imn is set to 0
at power-up.
Imx: Maximum Current Alert Threshold Exceeded. This bit is set to a 1 whenever a Current register reading is above the
maximum IAlrtTh value. This bit is cleared automatically when Current falls below maximum IAlrtTh value. Imx is set to 0
at power-up.
dSOCi: State-of-Charge 1% Change Alert. This is set to 1 whenever the RepSOC register crosses an integer percentage
boundary such as 50.0%, 51.0%, etc. Must be cleared by host software. dSOCi is set to 0 at power-up.
Vmn: Minimum Voltage Alert Threshold Exceeded. This bit is set to a 1 whenever a VCell register reading is below the
minimum VAlrtTh value. This bit may or may not need to be cleared by system software to detect the next event. See
Config.VS bit description. Vmn is set to 0 at power-up.
Tmn: Minimum Temperature Alert Threshold Exceeded. This bit is set to a 1 whenever a Temperature register reading
is below the minimum TAlrtTh value. This bit may or may not need to be cleared by system software to detect the next
event. See Config.TS bit description. Tmn is set to 0 at power-up.
Smn: Minimum SOC Alert Threshold Exceeded. This bit is set to a 1 whenever SOC falls below the minimum SAlrtTh
value. This bit may or may not need to be cleared by system software to detect the next event. See Config.SS and
MiscCFG.SACFG bit descriptions. Smn is set to 0 at power-up.
Vmx: Maximum Voltage Alert Threshold Exceeded. This bit is set to a 1 whenever a VCell register reading is above the
maximum VAlrtTh value. This bit may or may not need to be cleared by system software to detect the next event. See
Config.VS bit description. Vmx is set to 0 at power-up.
Tmx: Maximum Temperature Alert Threshold Exceeded. This bit is set to a 1 whenever a Temperature register reading
is above the maximum TAlrtTh value. This bit may or may not need to be cleared by system software to detect the next
event. See Config.TS bit description. Tmx is set to 0 at power-up.
Smx: Maximum SOC Alert Threshold Exceeded. This bit is set to a 1 whenever SOC rises above the maximum SAlrtTh
value. This bit may or may not need to be cleared by system software to detect the next event. See Config.SS and
MiscCFG.SACFG bit descriptions. Smx is set to 0 at power-up.
PA: Protection Alert. This bit is set to a 1 when there is a protection event. The details of which protection event can be
found in the ProtAlrts register. This bit must be cleared by system software to detect the next protection event. However,
prior to clearing this bit, the ProtAlrts register must first be written to 0x0000. ProtAlrt is set to 0 at power-up.
X: Don’t Care. This bit is undefined and can be logic 0 or 1.
www.maximintegrated.com
Maxim Integrated | 89
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Status2 Register (0B0h)
Register Type: Special
Nonvolatile Backup: None
Initial Value: 0x0000
The Status2 register maintains status of hibernate mode. Table 44 shows the Status2 register format.
Table 44. Status2 Register (0B0h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Hib
x
Hib: Hibernate Status. This bit is set to a 1 when the device is in hibernate mode or 0 when the device is in active mode.
Hib is set to 0 at power-up.
X: Don’t Care. This bit is undefined and can be logic 0 or 1.
nBattStatus Register (1A8h)
Battery Status Nonvolatile Register
The Battery Status register contains the permanent battery status information. If nProtCfg.PFen = 1, then a permanent
fail results in permanently turning the FETs off to ensure the safety of the battery and the PFAIL pin is driven high.
Table 45. nBattStatus Register (1A8h) Format
D15
D14
D13
D12
D11
D10
D9
D8
PermFail
OVPF
OTPF
CFETFs
DFETFs
FETFo
LDet
ChksumF
D7
D6
D5
D4
D3
D2
D1
D0
LeakCurr
PermFail—Permanent Failure. This bit is set if any permanent failure is detected.
CFETFs—ChargeFET failure-short detected. If the IC detects that the charge FET is shorted and cannot be opened, it
sets the CFETFs bit and the PermFail bit. This function is enabled with nProtCfg.FetPFEn.
DFETFs—DischargeFET failure-short detected. If the IC detects that the discharge FET is shorted and cannot be
opened, it sets the DFETFs and the PermFail bit. This function is enabled with nProtCfg.FetPFEn.
FETFo—FET Failure Open. If the IC detects an open FET failure it sets FETFo. In this case, if the IC detects either CHG
or DIS FET to have failed open, then it sets FETFo. This function is enabled with nProtCfg.FetPFEn.
LDet—Leakage Detection Fault. This bit is set when a leakage detection fault has been detected.
ChksumF—Checksum Failure. ChksumF protection related NVM configuration registers checksum failure. In the case
of a checksum failure, the device sets the PermFail bit but does not write it to NVM in order to prevent using an additional
NVM write. This allows the PermFail bit to be cleared by the host so that the INI file can be reloaded.
LeakCurr—Leakage Current. Leakage current is an unsigned 8-bit result of leakage current from self-discharge in a cell.
This field saves the leakage current from the LeakCurrRep register. The LSB for this field is 3.125μV (or 0.625mA with a
5mΩ R
with a range of 0mA to 159.375mA).
SENSE
nFaultLog Register (1AEh)
This register has dual functionality depending on configuration settings. If nNVCfg2.enFL = 1, the nFaultLog register
contains a history of protection events that have been logged at any moment by the device during the log interval and is
formatted as shown in Table 46.
Alternatively, if nNVCfg0.enAF = 1, the register becomes repurposed for Age Forecasting data. If neither option is
enabled, this register can be used as general-purpose user memory.
This register is periodically saved to nonvolatile memory as part of the life-logging function.
www.maximintegrated.com
Maxim Integrated | 90
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 46. nFaultLog Register (1AEh) Format
D15
D14
D13
D12
D11
D10
D9
D8
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
D7
D6
D5
D4
D3
D2
D1
D0
TooHotC
TooColdC
OVP
OCCP
DieHot
Imbalance
UVP
ODCP
ProtStatus Register (0D9h)
The Protection Status register contains the fault states of the protection state machine
Table 47. ProtStatus Register (0D9h) Format
D15
D14
D13
D12
D11
D10
D9
D8
ChgWDT
TooHotC
Full
TooColdC
OVP
OCCP
Qovflw
PreqF
D7
D6
D5
D4
D3
D2
D1
D0
Imbalance
PermFail
DieHot
TooHotD
UVP
ODCP
ResDFault
Ship
Ship—A flag to indicate the ship state.
PermFail—Permanent Failure Detected. See the Permanent Failure section for details.
Discharging Faults:
ODCP - Overdischarge current
UVP - Undervoltage
TooHotD - Overtemperature for discharging
DieHot - Overtemperature for die temperature
Charging Faults:
TooHotC- Overtemperature for charging
OVP - Overvoltage
OCCP - Overcharge current
Qovrflw - Capacity overflow
TooColdC - Undertemperature for charging
Full - Full detection
ChgWDT - Charge communication watchdog timer
DieHot - Overtemperature for die temperature
Imbal - Multicell imbalance
PreqF - Prequal timeout
See the Protector section for details of each fault.
www.maximintegrated.com
Maxim Integrated | 91
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
ProtAlrt Register (0AFh)
The Protection Alerts register contains a history of any protection events that have been logged by the device and is
formatted as shown in Table 48. If any bit of ProtAlrt is 1, then the Status.PA bit is also 1 if Config.ProtAlrtEn = 1. Once a
bit is set, it remains set until cleared by the host. The Alert pin is driven low if Config.AEn = 1 and Config.ProtAlrtEn = 1.
The bits in ProtAlrt mirror the bits in ProtStatus with the exception of the LDET bit.
Table 48. ProtAlrt Register (0AFh) Format
D15
D14
D13
D12
D11
D10
D9
D8
ChgWDT
TooHotC
Full
TooColdC
OVP
OCCP
Qovflw
PreqF
D7
D6
D5
D4
D3
D2
D1
D0
Imbalance
PermFail
DieHot
TooHotD
UVP
ODCP
ResDFault
LDet
HProtCfg2 Register (1F1h)
Register Type: Special
Nonvolatile Backup: None
POR Value: 0x0000
The HProtCfg2 Register provides the status of the protection FETs and a variety of other functions as shown in Table 49.
Table 49. HProtCfg2 Register (1F1h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
AOLDO
CommOvrd
CPCfg
PBEN
DISs
CHGs
CHGs: CHG FET Status, 1 = On, 0 = Off.
DISs: DIS FET Status, 1 = On, 0 = Off.
PBEN: Pushbutton Enable. 1 = Pushbutton wakeup on ALRT pin is enabled. 0 = Disabled.
CPCfg: Charge Pump Gate Drive Voltage Configuration. 00b = 6V, 01b = 8V, 10b = 10V.
CommOvrd: Command Override Enable. 1 = FET override function enabled. Allows communication to turn off CHG, DIS
FETs by writing the CommStat register. 0 = FET override function disabled.
AOLDO: Always-on LDO Configuration.
AOLDO VALUE
DESCRIPTION
00b
01b
10b
11b
AOLDO is disabled.
AOLDO is enabled. Output is 3.4V
AOLDO is enabled. Output is 1.8V.
AOLDO is enabled. Output is 3.4V.
Nonvolatile Memory Status
The IC reports the status of nonvolatile memory operations by updating the NVBusy and NVError bits in the CommStat
register to indicate when the nonvolatile memory is busy, idle, or if there has been an error.
Analog Measurement Registers
The IC monitors cell pack voltage, cell pack current, cell pack temperature, and the voltage of the cell. This information is
provided to the fuel gauge algorithm to predict cell capacity and also made available to the user. Note that ADC related
register information is not maintained while the IC is in shutdown mode. The following register information is invalid until
the first measurement cycle after the IC returns to active mode of operation.
www.maximintegrated.com
Maxim Integrated | 92
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Voltage Measurement
VCell Register (01Ah)
Register Type: Voltage
Nonvolatile Backup: None
Each update cycle, the lowest reading from all cell voltage measurements is placed in the VCell register. VCell is used
as the voltage input to the fuel gauge algorithm.
AvgVCell Register (019h)
Register Type: Voltage
Nonvolatile Backup: None
The AvgVCell register reports an average of the VCell register readings. The time period for averaging is configurable
from a 12 second to 24 minute time period. See the nFilterCfg register description for details on setting the time filter.
The first VCell register reading after power-up or exiting shutdown mode sets the starting point of the AvgVCell register.
Note that when a cell relaxation event is detected, the averaging period changes to the period defined by the RelaxCfg.dt
setting. The register reverts back to its normal averaging period when a charge or discharge current is detected.
Cell1-Cell4 Registers (0D8h-0D5h)
Register Type: Voltage
Nonvolatile Backup: None
Each update cycle, the cell voltage measurement for each cell is placed in appropriate the Cell1-Cell4 register.
AvgCell1-AvgCell4 Registers (0D4h-0D1h)
Register Type: Voltage
Nonvolatile Backup: None
The AvgCell1-AvgCell4 registers report an 8-sample filtered average of the corresponding Cell1-Cell4 register readings.
Batt Register (0DAh)
Register Type: Special
Nonvolatile Backup: None
The Batt registers contains the total pack voltage measured inside the protector on a 20.48V scale with an LSB of
0.3125mV.
PCKP Register (0DBh)
Register Type: Special
Nonvolatile Backup: None
The PCKP register contains the voltage between PACK+ and GND on a 20.48V scale with an LSB of 0.3125mV.
www.maximintegrated.com
Maxim Integrated | 93
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
MaxMinVolt Register (0008h)
Register Type: Special
Nonvolatile Backup: Saves to nMaxMinVolt (1ACh) if nNVCfg2.enMMV is set (does not restore from nonvolatile).
Initial Value: 0x00FF
The MaxMinVolt register maintains the maximum and minimum of all cell voltage readings since device reset. Each
time the voltage registers update, they are compared against these values. If a new voltage channel reading is larger
than the maximum or less than the minimum, the corresponding value is replaced with the new reading. At power-up,
the maximum voltage value is set to 00h (the minimum) and the minimum voltage value is set to FFh (the maximum).
Therefore, both values are updated after the first update. Host software can reset this register by writing it to its power-up
value of 0x00FF. The maximum and minimum voltages are each stored as 8-bit values with a 20mV resolution. Table 50
shows the register format.
Table 50. MaxMinVolt (008h)/nMaxMinVolt (1ACh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MaxVCELL
MinVCELL
MaxVCELL: Maximum channel voltage reading (20mV resolution)
MinVCELL: Minimum VCell register reading (20mV resolution)
MaxMinVolt is not cumulative across the entire battery lifetime. After each periodic nonvolatile-memory save, MaxMinVolt
resets to 0x00FF to find the next max/min volt across the next segment of battery life. This behavior helps provide a
useful log across the battery lifetime where each log segment shows the maximum and minimum voltage experienced
across only that segment.
Current Measurement
The IC is able to monitor the current flow through the cell pack by measuring the voltage between the CSN and CSP
pins over a ±51.2mV range. While in active mode updates occur in intervals of 351.5ms. In hibernate mode, the update
interval is set by the nHibCfg register. All ICs are calibrated for current-measurement accuracy at the factory. However,
if the application requires, Current register readings can be adjusted by changing the nCGain register setting.
If the application uses a sense resistor with a large temperature coefficient such as a copper metal board trace, current
readings can be adjusted based on the temperature measured by the IC. The CGTempCo register stores a percentage
per degrees Celsius value that is applied to current readings if the nNVCfg2.enMet bit is set. If nNVCfg1.enMtl = 0, the
default temperature coefficient of copper is used for temperature adjustments. If enMtl = 1, the CGTempCo register value
is used for temperature adjustments.
Additionally, the IC maintains a record of the minimum and maximum current measured by the IC and an average current
over a time period defined by the host. Contents of the Current and AvgCurrent registers are indeterminate for the first
conversion cycle time period after IC power-up.
Current Measurement Timing
Current measurements are always enabled regardless of nPackCfg settings. Current is updated every 351ms.
Current Register (01Ch)
Register Type: Current
Nonvolatile Backup: None
The IC measures the voltage between the CSP and CSN pins and the result is stored as a two’s complement value in the
Current register. Voltages outside the minimum and maximum register values are reported as the minimum or maximum
value. The register value should be divided by the sense resistance to convert to amps. The value of the sense resistor
determines the resolution and the full-scale range of the current readings. Table 51 shows range and resolution values
for typical sense resistances.
www.maximintegrated.com
Maxim Integrated | 94
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 51. Current Measurement Range and Resolution vs. Sense Resistor Value
SENSE
RESISTOR nRSENSE
(mΩ)
CURRENT
REGISTER
RANGE (A)
CAPACITY
RESOLUTION
(mAh)
MAXIMUM
CAPACITY
(mAh)
BATTERY FULL
CAPACITY (mAh)
CURRENT REGISTER
RESOLUTION (μA)
> 4000
> 2000
> 800
> 400
> 200
1
2
0064h
00C8h
01F4h
03E8h
07D0h
1562.5
781.25
312.5
±51.2
±25.6
±10.24
±5.12
±2.56
5
2.5
1
144360
71680
28672
14336
7168
5
10
20
156.25
78.125
0.5
0.25
AvgCurrent Register (01Dh)
Register Type: Current
Nonvolatile Backup: None
The AvgCurrent register reports an average of Current register readings over a configurable 0.7 second to 6.4 hour time
period. See the nFilterCfg register description for details on setting the time filter. The first Current register reading after
returning to active mode sets the starting point of the AvgCurrent filter.
MaxMinCurr Register (00Ah)
Register Type: Special
Nonvolatile Backup: Periodically saves to nMaxMinCurr (1ABh) if nNVCfg2.enMMC is set, but does not restore from
nonvolatile memory.
Alternate Initial Value: 0x807F
The MaxMinCurr register maintains the maximum and minimum Current register values since the last IC reset or until
cleared by host software. Each time the Current register updates, it is compared against these values. If the reading is
larger than the maximum or less than the minimum, the corresponding value is replaced with the new reading. At power-
up, the maximum current value is set to 80h (the minimum) and the minimum current value is set to 7Fh (the maximum).
Therefore, both values are changed to the Current register reading after the first update. Host software can reset this
register by writing it to its power-up value of 0x807F. The maximum and minimum voltages are each stored as two’s
complement 8-bit values with 0.4mV/RSENSE resolution. Table 52 shows the register format.
Table 52. MaxMinCurr (00Ah)/nMaxMinCurr (1ABh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MaxCurrent
MinCurrent
MaxCurrent: Maximum Current register reading (0.40mV resolution)
MinCurrent: Minimum Current register reading (0.40mV resolution)
MaxMinCurr is not cumulative across the entire battery lifetime. After each periodic nonvolatile-memory save,
MaxMinCurr resets to 0x807F to find the next maximum and minimum current across the next segment of battery life.
This behavior helps provide a useful log across the battery lifetime where each log segment shows the maximum and
minimum current experienced across only that segment.
nCGain Register (1C8h)
Register Type: Special
Factory Default Value: 4000h
The nCGain register adjusts the gain and offset of the current measurement result. The current measurement ADC is
factory trimmed to data-sheet accuracy without the need for the user to make further adjustments. The recommended
default for the nCGain register is 0x4000 which applies no adjustments to the Current register reading.
www.maximintegrated.com
Maxim Integrated | 95
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
For specific application requirements, the CGain and COff values can be used to adjust readings as follows:
Current Register = (Current ADC Reading × (CGain/256)) + COff
CGain and COff are combined into a single register formatted as shown in Table 53.
Table 53. nCGain Register (1C8h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CGain
COff
COff: COff has a range of -32 to +31 LSbs. However, it is normally not recommended to calibrate COff. COff = 0 is
recommended for most applications.
CGain: The recommended default value of CGain = 0x100 corresponds to a gain of 1. CGain can be calculated as
follows: CGain = ((MeasuredCurrent/ReportedCurrent) × 0x0100). CGain is a signed value and can be negative.
CGTempCo (0B8h)/nCGTempCo (1C9h) Register
Register Type: Special
Factory Default Value: 0000h
Alternate Initial Value: 20C8h
Set nNVCfg2.enMet = 1 to use CGTempCo to adjust current measurements for temperature. CGTempCo has a range of
0% to 3.1224% per degrees Celsius with a step size of 3.1224/65536 percent per degrees Celsius. If the nNVCfg1.enMtl
bit is clear, CGTempCo defaults to a value of 20C8h (compensation for copper) or 0.4% per degrees Celsius which is
the approximate temperature coefficient of a copper trace. If the nNVCfg1.enMtl bit is set, CGTempCo restores from
nCGTempCo (1C9h) after IC reset allowing a custom sense resistor temperature coefficient to be used.
nRSense Register (1CFh)
Register Type: Special
Factory Default Value: 01F4h
Nonvolatile Restore: There is no associated restore location for this register.
The nRSense register is the designated location to store the nominal sense resistor value used by the application. This
value is not used by the IC as all current and capacity information is reported in terms of μV and μVH. Host software can
use the nRSense register value to convert current and capacity information into mA and mAH. It is recommended that
the sense resistor value be stored with an LSb weight of 10μΩ giving a range of 10μΩ to 655.35mΩ. Table 51 shows
recommended register settings based on common sense resistor values.
Copper Trace Current Sensing
The IC has the ability to measure current using a copper board trace instead of a traditional sense resistor. The main
difference being the ability to adjust to the change in sense resistance over temperature. To enable copper trace current
sensing, set nNVCfg2.enMet = 1. The ICs default temperature adjustment is 0.4% per °C but can be adjusted using the
nTCurve register if nNVCfg1.enMtl = 1. Note that copper trace current sensing cannot be enabled at the same time as
thermistor curve adjustment. For 1-ounce copper, a length to width ratio of 6:1 creates a 0.0035Ω sense resistor which is
suitable for most applications. Table 54 summarizes the IC setting for copper trace sensing.
Table 54. Copper Trace Sensing
PARAMETER
nNVCfg1.enMet
nNVCfg2.enMlt
nRense
SETTING
RESULT
1
0
Sense resistor temperature compensation enabled.
Sense resistor temperature compensation set to default of 0.4% per °C (typical copper).
Sense resistor indicator to host software set to 0.0035Ω.
0x012C
6:1
R
Size
A 6:1 length to width ratio of 1oz copper gives a resistance of 0.0035Ω.
SENSE
www.maximintegrated.com
Maxim Integrated | 96
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Temperature Measurement
The IC measures its own internal die temperature and up to four thermistors. See the nPackCfg register for details.
Every 1.4s the IC biases a thermistor with an internal trimmed pullup. After the pullup is enabled, the IC waits for a
settling period of tPRE prior to making measurements on the TH(1-4) pin. The active pullup is disabled when temperature
measurements are complete. This feature limits the time the external resistor-divider network is active and lowers the
total amount of energy used by the system.
The ratiometric results are converted to temperature using the nThermCfg register each time one of the TH(1-4) pins are
measured. Proper nThermCfg configuration is needed to achieve thermistor accuracy from -40°C to +85°C. Internal die
temperature measurements are factory calibrated and are not affected by nThermCfg register settings.
Additionally, the IC maintains a record of the minimum and maximum temperature measured and an average
temperature over a configurable time period. See the nFilterCfg for details.
Temperature Measurement Timing
Temperature measurement channels are individually enabled using the nPackCfg register. ADC measurement order and
firmware post-processing determine when a valid reading becomes available to the user. In addition, not all channels
are measured each time through the firmware task loop. Selection options for enabled channels create a large number
of possible timing options. DieTemp is updated every 351ms. Each thermistor measurement is updated every 1.4s x
NTherms.
Temp Register (01Bh)
Register Type: Temperature
Nonvolatile Backup: None
The Temp register is the input to the fuel gauge algorithm. The Temp register reflects the highest thermistor temperature
if enabled, and the die-temperature if the thermistors are disabled.
AvgTA Register (016h)
Register Type: Temperature
Nonvolatile Backup: None
The AvgTA register reports an average of the readings from the Temp register. The averaging period is configurable from
6 minutes up to 12 hours as set by the FilterCfg register. The first Temp register reading after returning to active mode
sets the starting point of the averaging filters.
MaxMinTemp Register (009h)
Register Type: Special
Nonvolatile Backup: Periodically saves to nMaxMinTemp (1ADh) if nNVCfg2.enMMT is set, but does not restore from
nonvolatile memory.
Alternate Initial Value: 807Fh
The MaxMinTemp register maintains the maximum and minimum Temp register (01Bh) values since the last fuel-gauge
reset or until cleared by host software. Each time the Temp register updates, it is compared against these values. If
the reading is larger than the maximum or less than the minimum, the corresponding values are replaced with the new
reading. At power-up, the maximum value is set to 80h (minimum) and the minimum value is set to 7Fh (maximum).
Therefore, both values are changed to the Temp register reading after the first update. Host software can reset this
register by writing it to its power-up value of 807Fh. The maximum and minimum temperatures are each stored as two’s
complement 8-bit values with 1°C resolution. Table 55 shows the format of the register.
Table 55. MaxMinTemp (009h)/nMaxMinTemp (1ADh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
MaxTemperature
MinTemperature
www.maximintegrated.com
Maxim Integrated | 97
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
MaxTemperature: Maximum Temp register reading (1ºC resolution)
MinTemperature: Minimum Temp register reading (1ºC resolution)
MaxMinTemp is not cumulative across the entire battery lifetime. After each periodic nonvolatile memory save,
MaxMinTemp resets to 807Fh to find the next maximum and minimum temperatures across the next segment of battery
life. This behavior helps provide a useful log across the battery lifetime where each log segment shows the maximum
and minimum temperature experienced across only that segment.
nThermCfg Register (1CAh)
Factory Default Value: 71BEh
External NTC thermistors generate a temperature related voltage measured at the TH(1-4) pins. Set nThermCfg register
to compensate thermistor for accurate translation of temperature.
Table 56 lists common NTC thermistors with their associated Beta value and the nThermCfg value. The thermistors in
the table translate within ±1°C from -40°C to +85°C. For other thermistors, use the equation to translate within ±2.5°C.
Table 56. Register Settings for Common Thermistor Types
BETA
@ 25°C-85°C
THERMISTOR
R
(kΩ)
nTHERMCFG
25C
Murata NCP15XH103F03RC
Semitec 103AT-2
10
3435
71BEh
91C3h
5183h
48EBh
08D9h
10
10
3435
TDK B57560G1103 7003
Murata NCU15WF104F6SRC
NTC TH11-4H104F
TDK NTCG064EF104FTBX
Other 10K
3610
100
100
100
10
4250
4510
4225
58EFh
1
nThermCfg = 7000h + (3245919/Beta - 512)
1
Other 100K
100
nThermCfg = 3000h + (3245919/Beta - 512)
1. Use Beta 25°C-85°C.
DieTemp Register (034h)
Register Type: Temperature
Nonvolatile Backup: None
This register displays temperature in degrees Celsius, ±128°C or 1°C in the high-byte or 1/256°C LSB.
AvgDieTemp Register (040h)
Register Type: Temperature
Nonvolatile Backup: None
The AvgDieTemp register reports a 4-sample filtered average of the DieTemp register.
Temp1/2/3/4 Registers (13Ah-137h)
Register Type: Temperature
Nonvolatile Backup: None
These registers display temperature readings from thermistor 1/2/3/4 (if enabled) in degrees Celsius, ±128ºC or 1°C in
the high-byte or 1/256°C LSB.
www.maximintegrated.com
Maxim Integrated | 98
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
AvgTemp1/2/3/4 Registers (136h-133h)
Register Type: Temperature
Nonvolatile Backup: None
The AvgTemp1/2/3/4 registers report a 4-sample filtered average of the Temp1/2/3/4 registers.
Power
Power Register (0B1h)
Instantaneous power calculation from immediate current and voltage. LSB is 0.4mW with a 5mΩ sense resistor.
AvgPower Register (0B3h)
Filtered Average Power from the power register. LSB is 0.4mW with a 5mΩ sense resistor. Filter bits located in
Config2.POWR.
Charge Control Registers
ChargingCurrent Register (028h)
Register Type: Current
Nonvolatile Backup: None
The ChargingCurrent register reports the prescribed charging current. See the Charging Prescription section for more
details.
ChargingVoltage Register (02Ah)
Register Type: Voltage
Nonvolatile Backup: None
The ChargingVoltage register reports the prescribed charging voltage. See the Charging Prescription section for more
details.
nStepChg Register (1DBh)
Factory Default Value: C884h
The nStepChg register defines the step-charging prescription as shown in Figure 10.
Note: This only effects the ChargingCurrent output register which prescribes a charge current controlled by the external
charger. To disable step-charging prescription, set nStepChg = FF00h.
Table 57. nStepChg Register (1DBh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
StepCurr1
StepCurr2
StepdV0
StepdV1
StepCurr1 and StepCurr2: Both of these register bit-fields scale the JEITA zone charge current down by a 4-bit ratio
from 1/16 to 16/16.
StepCurrent1 = ChargingCurrent
StepCurrent2 = ChargingCurrent
x StepCurr1/16 = 2000mA x 12/16 = 1500mA
x StepCurr2/16 = 2000mA x 8/16 = 1000mA
JEITAZONE
JEITAZONE
www.maximintegrated.com
Maxim Integrated | 99
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
StepdV0 and StepdV1: These register bit-fields configure StepVolt0 and StepVolt1 relative to the JEITA zone charge
voltage. Both registers are negative offsets relative to JEITA ChargeVoltage, and both registers support 10mV LSB.
StepV0 = ChargingVoltage
StepV1 = ChargingVoltage
- (StepdV0 x 10mV) = 4.2V - (8 x 10mV) = 4.12V
- (StepdV1 x 10mV) = 4.2V - (4 x 10mV) = 4.16V
JEITAZONE
JEITAZONE
nChgCfg (1C2h) Prequal Configuration
Set nProtCfg.PreqEn to enable the prequal charging feature and configure the settings as shown in Table 58. Set
nChgCtl (1C3h) = 00E1h for proper operation.
Factory Default nChgCfg Value: 2061h
Factory Default nChgCtl Value: 00E1h
The IC regulates the CHG gate voltage in order to control/limit the following:
● Charge Current
● CHG FET and DIS FET Temperature (using DieTemp)
Table 58. nChgCfg Register (1C2h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
1
PreQualVolt
HeatLim
PreChgCurr
PreQualVolt: Sets the prequal voltage. Prequal Voltage = UVP + PreQualVolt x 20mV, PreQualVolt is a signed 2's
compliment value with range of UVP – 320mV to UVP + 300mV.
PreChgCurr: Sets the precharging current for the ChargingCurrent register. Precharge current is calculated as:
PreChargeCurrent = nJEITAC.RoomChargingCurrent x PreChgCurr/128 (range from RoomChargingCurrent/128 to
RoomChargingCurrent/4)
HeatLim: Set HeatLim to limit the thermal dissipation in the protection FETs during prequal regulation. Set HeatLim from
102mW to 819mW in 102mW steps. The effective power-dissipation limit is (HeatLim + 1) x 102mW.
ModelGauge m5 Algorithm Registers
ModelGauge m5 Registers
For accurate results, ModelGauge m5 uses information about the cell and the application as well as the real-time
information measured by the IC. Figure 26 shows inputs and outputs to the algorithm grouped by category. Analog
input registers are the real-time measurements of voltage, temperature, and current performed by the IC. Application-
specific registers are programmed by the customer to reflect the operation of the application. The Cell Characterization
Information registers hold characterization data that models the behavior of the cell over the operating range of the
application. The Algorithm Configuration registers allow the host to adjust the performance of the IC for its application.
The Learned Information registers allow an application to maintain the accuracy of the fuel gauge as the cell ages. The
register description sections describe each register function in detail.
www.maximintegrated.com
Maxim Integrated | 100
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
VCELL
AVCAP / AVSOC
REPCAP / REPSOC
MIXCAP / MIXSOC
FULLCAP
CURRENT
TEMPERATURE
AVGVCELL
AVGCURRENT
AVGTEMPERATURE
FULLCAPREP
FULLCAPNOM
RSLOW
TTE / TTF / AtTTE
VFOCV / VFSOC
VRIPPLE
NDESIGNVOLT
NDESIGNCAP
NICHGTERM
AGE
ModelGauge m5
AGEFORECAST
ALGORITHM
CYCLES
CHARACTERIZATION
NRIPPLECFG
TABLES
NCONVGCFG
FULLCAPNOM
NCVCFG
CYCLES
NQRTABLES00,10,20,30
NFULLSOCTHR
NRCOMP0
NAGEFCCFC
TIMERH
NLEARNCFG
NQRTABLES00,10,20,30
NFLITERCFG
NIAVGEMPTY
NFULLCAPNOM
NVEMPTY
NRELAXCFG
RCOMP0
NMISCCFG
TEMPCO
NTEMPCO
ATRATE
FULLCAPREP
NIAVGEMPTY
Figure 26. ModelGauge m5 Registers
ModelGauge m5 Algorithm Output Registers
The following registers are outputs from the ModelGauge m5 algorithm. The values in these registers become valid
480ms after the IC is reset.
RepCap Register (005h)
Register Type: Capacity
Nonvolatile Backup: None
RepCap or Reported Capacity is a filtered version of the AvCap register that prevents large jumps in the reported value
caused by changes in the application such as abrupt changes in temperature or load current. See the Fuel-Gauge Empty
Compensation section for details.
RepSOC Register (006h)
Register Type: Percentage
Nonvolatile Backup: None
RepSOC is a filtered version of the AvSOC register that prevents large jumps in the reported value caused by changes
www.maximintegrated.com
Maxim Integrated | 101
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
in the application such as abrupt changes in load current. RepSOC corresponds to RepCap and FullCapRep. RepSOC
is intended to be the final state-of-charge percentage output for use by the application. See the Fuel-Gauge Empty
Compensation section for details.
FullCapRep Register (010h)
Register Type: Capacity
Nonvolatile Backup and Restore: nFullCapRep (1A9h) or nFullCapNom (1A5h)
This register reports the full capacity that goes with RepCap, generally used for reporting to the user. A new full-capacity
value is calculated at the end of every charge cycle in the application.
TTE Register (011h)
Register Type: Time
Nonvolatile Backup: None
The TTE register holds the estimated time-to-empty for the application under present temperature and load conditions.
The TTE value is determined by dividing the AvCap register by the AvgCurrent register. The corresponding AvgCurrent
filtering gives a delay in TTE empty, but provides more stable results. The TTE register has a maximum value of 102.3
hours. When TTE is larger than the maximum value, the TTE register saturates and contains the maximum value
(FFFFh). The host can calculate times longer than the maximum value with the following equation:
TTE
(hours) = AvCap(mAh)/AvgCurrent(mA)
CALCULATED
See the Typical Operating Characteristics for sample performance.
TTF Register (020h)
Register Type: Time
Nonvolatile Backup: None
The TTF register holds the estimated time-to-full for the application under present conditions. The TTF value is
determined by learning the constant current and constant voltage portions of the charge cycle based on experience of
prior charge cycles. Time-to-full is then estimated by comparing the present charge current to the charge termination
current. Operation of the TTF register assumes all charge profiles are consistent in the application. See the nTTFCfg for
configuration and the Typical Operating Characteristics for sample performance.
Age Register (007h)
Register Type: Percentage
Nonvolatile Backup: None
The Age register contains a calculated percentage value of the application’s present cell capacity compared to its
expected capacity. The result can be used by the host to gauge the battery pack health as compared to a new pack of
the same type. The equation for the register output is:
Age Register = 100% x (FullCapRep register/DesignCap register)
Cycles Register (017h) and nCycles (1A4h)
Register Type: Special
Nonvolatile Backup and Restore: nCycles (1A4h)
The Cycles register maintains a total count of the number of charge/discharge cycles of the cell that have occurred. The
result is stored as a percentage of a full cycle. For example, a full charge/discharge cycle results in the Cycles register
incrementing by 100%. The Cycles register has a full range of 0 to 16383 cycles with a 25.0% LSb. Cycles is periodically
saved to nCycles to provide a long term nonvolatile cycle count.
www.maximintegrated.com
Maxim Integrated | 102
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 59. Cycles Register (017h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CycleCount (LSb 25%)
Table 60. nCycles Register (1A4h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CycleCount (LSb 25%, 50%, 100%, or 200%)
nFib
The LSb of Cycles register is 25%.
The LSb of nCycles.CycleCount depends on the setting of nNVCfg2.fibScl as shown in Table 61.
Configure nFib = 0 for any new pack. nFib is a reset counter which controls Fibonacci-saving reset accelleration (see
the 100 Record Life Logging section). Each reset followed by any nonvolatile save increases by 1. Maximum value is 7
without overflow.
Table 61. nNVCfg2.FibScl Setting Determines LSb of nNVCfg2.CyclesCount
NNVCFG2.FIBSCL
NCYCLES.CYCLECOUNT LSB
00b
01b
10b
11b
25%
50%
100%
200%
Timer Register (03Eh)
Register Type: Special
Nonvolatile Backup: None
Initial Value: 0x0000
This register holds timing information for the fuel gauge. It is available to the user for debugging purposes. The Timer
register LSb is equal to 175.8ms giving a full-scale range of 0 to 3.2 hours.
TimerH Register (0BEh)
Register Type: Special
Nonvolatile Backup and Restore: nTimerH (1AFh) if nNVCfg2.enT is set
Alternate Initial Value: 0000h
This register allows the IC to track the age of the cell. An LSb of 3.2 hours gives a full-scale range for the register of up
to 23.94 years. If enabled, this register is periodically backed up to nonvolatile memory as part of the learning function.
FullCap Register (010h)
Register Type: Capacity
Nonvolatile Restore: Derived from nFullCapNom (1A5h)
This register holds the calculated full capacity of the cell based on all inputs from the ModelGauge m5 algorithm including
empty compensation. A new full-capacity value is calculated continuously as application conditions change.
nFullCapNom Register (1A5h)
Register Type: Capacity
Nonvolatile Backup and Restore: FullCapNom (023h)
www.maximintegrated.com
Maxim Integrated | 103
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
This register holds the calculated full capacity of the cell, not including temperature and empty compensation. A new full-
capacity nominal value is calculated each time a cell relaxation event is detected. This register is used to calculate other
outputs of the ModelGauge m5 algorithm.
RCell Register (014h)
Register Type: Resistance
Nonvolatile Backup: None
Initial Value: 0290h
The RCell register displays the calculated internal resistance of the cell or the average internal resistance of each cell in
the cell stack. RCell is determined by comparing open-circuit voltage (VFOCV) against measured voltage (VCell) over a
long time period while under load current.
VRipple Register (0B2h)
Register Type: Special
Nonvolatile Backup: None
Initial Value: 0000h
The VRipple register holds the slow average RMS value of the VCell register reading variation compared to the AvgVCell
register. The default filter time is 22.5s. See the nRippleCfg register description. VRipple has an LSb weight of 1.25mV/
128.
nVoltTemp Register (1AAh)
Register Type: Special
Nonvolatile Backup: AvgVCell and AvgTA registers if nNVCfg2.enVT = 1.
This register has dual functionality depending on configuration settings. If nNVCfg2.enVT = 1, this register provides
nonvolatile back up of the AvgVCell and AvgTA registers as shown in Table 62.
Table 62. nVoltTemp Register (1AAh) Format when nNVCfg2.enVT = 1
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
AvgVCell Upper 9 Bits
AvgTA Upper 7 Bits
Alternatively, if nNVCfg0.enAF = 1, this register stores an accumulated age slope value to be used with the Age
Forecasting algorithm. Regardless of which option is enabled, this register is periodically saved to nonvolatile memory as
part of the learning function. If neither option is enabled, this register can be used as general-purpose user memory.
ModelGauge m5 Algorithm Input Registers
The following registers are inputs to the ModelGauge algorithm and store characterization information for the application
cells as well as important application-specific specifications. They are described only briefly here. Contact Maxim for
information regarding cell characterization.
nXTable0 (180h) to nXTable11 (18Bh) Registers
Register Type: Special
Nonvolatile Restore: There are no associated restore locations for these registers.
Cell characterization information used by the ModelGauge algorithm to determine capacity versus operating conditions.
This table comes from battery characterization data. These are nonvolatile memory locations.
nOCVTable0 (190h) to nOCVTable11 (19Bh) Registers
Register Type: Special
Nonvolatile Restore: There are no associated restore locations for these registers.
www.maximintegrated.com
Maxim Integrated | 104
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Cell characterization information used by the ModelGauge algorithm to determine capacity versus operating conditions.
This table comes from battery characterization data. These are nonvolatile memory locations.
nQRTable00 (1A0h) to nQRTable30 (1A3h) Registers
Register Type: Special
Nonvolatile Backup and Restore: QRTable00 to QRTable30 (012h, 022h, 032h, 042h)
Factory Default Values: QRTable00 to QRTable30 (1050h, 8002h, 078Ch, 0880h)
The nQRTable00 to nQRTable30 register locations contain characterization information regarding cell capacity that is not
available under certain application conditions.
nFullSOCThr Register (1C6h)
Register Type: Percentage
Nonvolatile Restore: FullSOCThr (013h) if nNVCfg1.enFT is set.
Alternate Initial Value: 80%
The nFullSOCThr register gates detection of end-of-charge. VFSOC must be larger than the nFullSOCThr value before
nIChgTerm is compared to the AvgCurrent register value. The recommended nFullSOCThr register setting for most
custom characterized applications is 95% . For EZ performance applications, the recommendation is 80% (5005h). See
the nIChgTerm register description and End-of-Charge Detection section for details. Table 63 shows the register format.
Table 63. nFullSOCThr (1C6h)/FullSOCThr (013h) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
nFullSOCThr
1
0
1
nVEmpty Register (19Eh)
Register Type: Special
Nonvolatile Restore: VEmpty (03Ah) if nNVCfg0.enVE is set.
Alternate Initial Value: 9659h (3.0V/3.56V)
The nVempty register sets thresholds related to empty detection during operation. Table 64 shows the register format.
Table 64. VEmpty (03Ah)/nVEmpty (19Eh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
VE
VR
VE: Empty Voltage. Sets the voltage level for detecting empty. A 10mV resolution gives a 0 to 5.11V range. This value is
written to 3.3V after reset if nonvolatile backup is disabled.
VR: Recovery Voltage. Sets the voltage level for clearing empty detection. Once the cell voltage rises above this point,
empty voltage detection is re-enabled. A 40mV resolution gives a 0 to 5.08V range. This value is written to 3.88V after
reset if nonvolatile backup is disabled.
nDesignCap Register(1B3h)
Register Type: Capacity
Nonvolatile Restore: DesignCap (018h) if nNVCfg0.enDC is set
Alternate Initial Value: FullCapRep register value
The nDesignCap register holds the expected capacity of the cell. This value is used to determine age and health of the
cell by comparing against the measured present cell capacity.
nIChgTerm Register (19Ch)
Register Type: Current
www.maximintegrated.com
Maxim Integrated | 105
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Nonvolatile Restore: IChgTerm (01Eh) if nNVCfg0.enICT is set
Alternate Initial Value: 1/3rd the value of the nFullCapNom register (corresponds to C/9.6)
The nIChgTerm register allows the device to detect when a charge cycle of the cell has completed. nIChgTerm should
be programmed to the exact charge termination current used in the application. The device detects end-of-charge if all
the following conditions are met:
• VFSOC Register > FullSOCThr Register
• AND IChgTerm x 0.125 < Current Register < IChgTerm x 1.25
• AND IChgTerm x 0.125 < AvgCurrent Register < IChgTerm x 1.25
See the End-of-Charge Detection section for more details.
nRComp0 Register (1A6h)
Register Type: Special
Nonvolatile Restore: RComp0 (038h)
The nRComp0 register holds characterization information critical to computing the open circuit voltage of a cell under
loaded conditions.
nTempCo Register (1A7h)
Register Type: Special
Nonvolatile Restore: TempCo (039h)
The nTempCo register holds temperature compensation information for the nRComp0 register value.
ModelGauge m5 Algorithm Configuration Registers
The following registers allow operation of the ModelGauge m5 algorithm to be adjusted for the application. It is
recommended that the default values for these registers be used.
nConfig Register (1B0h)
Register Type: Special
Factory Default Value: 2290h
Nonvolatile Restore: Config (00Bh) and Config2 (0ABh)
The nConfig register holds all shutdown enable, alert enable, and temperature enable control bits. Writing a bit location
enables the corresponding function within one task period. Table 65, Table 66, and Table 67 show the register formats.
Table 65. nConfig Register (1B0h) Format
D15 D14 D13 D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
PAen SS TS VS FIFOen PBen DisBlockRead
0
AtRateEn COMMSH ALSH
1
FTHRM Aen dSOCen TAlrtEn
Table 66. Config Register (00Bh) Format
D15 D14 D13 D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2 D1
D0
0
SS TS VS DisLDO PBen DisBlockRead
0
SHIP COMMSH
0
ETHRM FTHRM Aen
0
PAen
Table 67. Config2 Register (0ABh) Format
D15
D14
D13
D12
D11 D10 D9 D8
D7
D6
TAlrtEn
D5 D4 D3 D2 D1 D0
DRCfg
POR_CMD
0
AtRtEn
ADCFIFOen
POWR
dSOCen
0
1
0
0
0: Bit must be written 0. Do not write 1.
1: Bit must be written 1. Do not write 0.
PAen: Protection Alert Enable. Set PAen = 1 to enable this feature that saves the protector faults (TooHotC, TooColdC,
www.maximintegrated.com
Maxim Integrated | 106
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
OVP, OCCP, DieHot, TooHotD, UVP, ODCP, LDet) into the low byte of the nBattStatus register. After each life logging
write to NVM, the low byte of nBattStatus is cleared.
PBEn: PushButton Enable. Set PBEn = 1 to enable wakeup by pushbutton. This application allows a product to be
completely sealed with battery disconnected until a shared system button is pressed.
Aen: Enable Alert on Fuel-Gauge Outputs. When Aen = 1, violation of any of the alert threshold register values by
temperature, voltage, or SOC triggers an alert. This bit affects the ALRT pin operation only. The Smx, Smn, Tmx, Tmn,
Vmx, Vmn, Imx, and Imn bits of the Status register (000h) are not disabled. Note that if this bit is set to 1, the ALSH bit
should be set to 0 to prevent an alert condition from causing the device to enter shutdown mode.
FTHRM: Force Thermistor Bias Switch. This allows the host to control the bias of the thermistor switch or enable
fast detection of battery removal. Set FTHRM = 1 to always enable the thermistor bias switch. With a standard 10kΩ
thermistor, this adds an additional 200μA, approximately, to the current drain of the circuit.
ETHRM: Enable Thermistor. Set to logic 1 to enable the automatic TH output bias and TH measurement.
COMMSH: Communication Shutdown. Set to logic 1 to force the device to enter shutdown mode if both SDA and SCL
2
are held low (I C version) or DQ is held low (1-Wire version) for more than the timeout of the ShdnTimer register. This
also configures the device to wake up on a rising edge of any communication. Note that if COMMSH is set to 0, the
device wakes up an edge of any of the SDA/DQ or SCL/OD pins. See the Modes of Operation section.
SHIP: Ship or Deepship Command. Write this bit to logic 1 to force into ship or deepship mode based on
nProtCfg.DeepShpEn after timeout of the Shutdown Timer register which is configured in nDelayCfg.UVPTimer. SHIP is
reset to 0 at power-up and upon exiting ship or deepship mode.
VS: Voltage ALRT Sticky. When VS = 1, voltage alerts can only be cleared through software. When VS = 0, voltage alerts
are cleared automatically when the threshold is no longer exceeded.
TS: Temperature ALRT Sticky. When TS = 1, temperature alerts can only be cleared through software. When TS = 0,
temperature alerts are cleared automatically when the threshold is no longer exceeded.
SS: SOC ALRT Sticky. When SS = 1, SOC alerts can only be cleared through software. When SS = 0, SOC alerts are
cleared automatically when the threshold is no longer exceeded.
POR_CMD: Firmware Restart. Set this bit to 1 to restart IC firmware operation without performing a recall of nonvolatile
memory into RAM. This allows different IC configurations to be tested without changing nonvolatile memory settings. This
bit is set to 0 at power-up and automatically clears itself after firmware restart.
TAlrten: Temperature Alert Enable. Set this bit to 1 to enable temperature based alerts. Write this bit to 0 to disable
temperature alerts. This bit is set to 1 at power-up.
dSOCen: SOC Change Alert Enable. Set this bit to 1 to enable the Status.dSOCi bit function. Write this bit to 0 to disable
the Status.dSOCi bit. This bit is set to 0 at power-up.
DRCfg: Deep Relax Time Configuration. 00b for 0.8 hours to 1.6 hours, 01b for 1.6 hours to 3.2 hours, 10b for 3.2 hours
to 6.4 hours and 11b for 6.4 hours to 12.8 hours.
POWR: Sets the time constant for the AvgPower register. The default POR value of 0000b gives a time constant of 0.7s.
The equation setting the period is:
(POWR-6)
AvgPower time constant = 45s x 2
FIFOen: ADC FIFO Enable. See the 16-reading ADC FIFO section for details. Set nConfig.ADCFIFOen = 1 to enable
continuous acquisition mode for ADC FIFO. Set nConfig.ADCFIFOen = 0 to disable continuous acquisition mode
for ADC FIFO. If continuous mode is disabled, a single-cycle acquisition mode for ADC FIFO is enabled by setting
Config2.ADCFIFOen = 1.
DisLDO: Disable AOLDO. Set DisLDO to 1 to disable the Always-On LDO if it is enabled in nPackCfg.AOCfg.
DisBlockRead: Disable SBS Block Read. Set DisBlockRead to 1 for normal read access in the 16h memory space. Clear
DisBlockRead to 0 to enable SBS block reads when SBS Mode is enabled with nNVCfg0.SBSen. The default setting for
DisBlockRead is 1.
www.maximintegrated.com
Maxim Integrated | 107
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
nNVCfg0 Register (1B8h)
Register Type: Special
Nonvolatile Restore: There is no associated restore location for this register.
Factory Default Value: 0A00h
The nNVCfg0 register manages nonvolatile memory backup of device and fuel gauge register RAM locations. Each bit
of the nNVCfg0 register, when set, enables a given register location to be restored from a corresponding nonvolatile
memory location after reset of the IC. If nonvolatile restore of a given register is not enabled, that location initializes to a
default value after reset instead. See the individual register descriptions for details. Table 68 shows the nNVCfg0 register
format.
Table 68. nNVCfg0 Register (1B8h) Format
D15
D14
D13
D12
D11
D10
D9
D8
enOCV
enX
enSHA
0
1
enFCfg
enRCfg
enLCfg
D7
D6
D5
D4
D3
D2
D1
D0
enICT
enDP
enVE
enDC
enMC
enAF
—
enSBS
enSBS: Enable SBS. This bit enables SBS functions of the IC. See the SBS section. When set, all registers accessed
with the SBS 2-Wire address are regularly updated. When this bit is clear, all SBS related nonvolatile configuration
register locations can be used as general-purpose user memory. In addition, setting enSBS = 1 enables the bus timeout
hardware required for proper SMBus support.
enAF: Enable Age Forecasting. Set this bit to enable Age Forecasting functionality. When this bit is clear, nAgeFcCfg
can be used for general-purpose data storage. When set, nVoltTemp becomes repurposed for Age Forecasting data.
When enAF is set to 1, nNVCfg2.enVT and nNVCfg2.enFL must be 0 for proper operation.
enMC: Enable MiscCfg restore. Set this bit to enable MiscCfg register to be restored after reset by the nMiscCfg register.
When this bit is clear, MiscCfg restores with its alternate initialization value and nMiscCfg can be used for general-
purpose data storage.
enDC: Enable DesignCap restore. Set this bit to enable DesignCap register to be restored after reset by the nDesignCap
register. When this bit is clear, DesignCap restores with its alternate initialization value and nDesignCap can be used for
general-purpose data storage.
enVE: Enable VEmpty restore. Set this bit to enable VEmpty register to be restored after reset by the nVEmpty register.
When this bit is clear, VEmpty restores with its alternate initialization value (3.0V) and nVEmpty can be used for general-
purpose data storage.
enDP: Enable Dynamic Power. Set this bit to enable Dynamic Power calculations. When this bit is set to 0, Dynamic
Power calculations are disabled and registers MaxPeakPower/SusPeakPower/MPPCurrent/SPPCurrent can be used as
general-purpose memory.
enICT: Enable IChgTerm restore. Set this bit to enable IChgTerm register to be restored after reset by the nIChgTerm
register. When this bit is clear, IChgTerm restores to a value of 1/3 C-rate (from FullCapNom) and nIChgTerm can be
used for general-purpose data storage.
enLCfg: Enable LearnCfg restore. Set this bit to enable LearnCfg register to be restored after reset by the nLearnCfg
register. When this bit is clear, LearnCfg restores with its alternate initialization value and nLearnCfg can be used for
general-purpose data storage.
enRCfg: Enable RelaxCfg restore. Set this bit to enable RelaxCfg register to be restored after reset by the nRelaxCfg
register. When this bit is clear, RelaxCfg restores with its alternate initialization value and nRelaxCfg can be used for
general-purpose data storage.
enFCfg: Enable FilterCfg restore. Set this bit to enable the FilterCfg register to be restored after reset by the nFilterCfg
register. When this bit is clear, FilterCfg restores with its alternate initialization value and nFilterCfg can be used for
general-purpose data storage.
www.maximintegrated.com
Maxim Integrated | 108
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
enSHA: Set to 1 to configure the MTP at address 0x1DC to 0x1DF as SHA space. Set to 0 to configure address 0x1DC
to 0x1DF as user MTP.
enX: Enable XTable restore. Set this bit to enable nXTable register locations to be used for cell characterization data.
When this bit is clear, the IC uses the default cell model and all nXTable register locations can be used as general-
purpose user memory.
enOCV: Enable OCVTable restore. Set this bit to enable nOCVTable register locations to be used for cell
characterization data. When this bit is clear, the IC uses the default cell model and all nOCVTable register locations can
be used as general-purpose user memory.
nNVCfg1 Register (1B9h)
Register Type: Special
Factory Default Value: 0182h
Nonvolatile Restore: There is no associated restore location for this register
The nNVCfg1 register manages nonvolatile memory restore of device and fuel gauge register RAM locations. Each bit
of the nNVCfg1 register, when set, enables a given register location to be restored from a corresponding nonvolatile
memory location after reset of the IC. If nonvolatile backup of a given register is not enabled, that location initializes to a
default value after reset instead. See the individual register descriptions for details. Table 69 shows the nNVCfg1 register
format.
Table 69. nNVCfg1 Register (1B9h) Format
D15
D14
D13
D12
D11
D10
D9
D8
0
enMtl
enFTh
0
0
enJP
enSC
enProt
D7
D6
D5
D4
D3
D2
D1
D0
enJ
enProtChksm
0
enTTF
enAT
0
enCTE
0
enProt: Enable Protector. Set this bit to enable the protector. When this bit is clear, protector is disabled.
enJ: Enable ChargingCurrent and ChargingVoltage. Set this bit to 1 to enable ChargingCurrent and ChargingVoltage
update feature.
enJP: Enable Protection with JEITA (temperature region dependent). Set this bit to 1 to enable JEITA Protection. Clear
this bit to disable JEITA protection and make OVP and OCCP thresholds become flat.
enSC: Enable special chemistry model. Set this bit to 1 if a special chemistry model is used. This bit enables the use of
nScOcvLim.
enCTE: Enable Converge-to-Empty. Set this bit to enable the nConvgCfg register settings to affect the converge to empty
functionality of the IC. When this bit is clear, converge-to-empty is disabled and nConvgCfg can be used for general-
purpose data storage.
enAT: Enable Alert Thresholds. Set this bit to enable IAlrtTh, VAlrtTh, TAlrtTh, and SAlrtTh registers to be restored
after reset by the nIAlrtTh, nVAlrtTh, nTAlrtTh, and nSAlrtTh registers respectively. When this bit is clear these registers
restore with their alternate initialization values and the nonvolatile locations can be used for general-purpose data
storage.
enTTF: Enable time-to-full configuration. Set to 1 to enable nTTFCfg (configures CVMixCap and CVHalftime) for tuning
of Time-To-Full performance. Otherwise, CVMixCap and CVHalftime restore to their alternate initialization values and
nTTFCfg can be used for general-purpose data storage.
enFTh: Enable FullSOCThr configuration restore. Set this bit to enable FullSOCThr register to be restored after reset
by the nFullSOCThr register. When this bit is clear FullSOCThr restores with its alternate initialization value (80%) and
nFullSOCThr can be used for general-purpose data storage.
www.maximintegrated.com
Maxim Integrated | 109
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
enMtl: Enable CGTempCo restore. Set this bit to enable CGTempCo register to be restored after reset by the nTCurve
register. When this bit is clear CGTempCo restores with its alternate initialization value (copper). nTCurve can be used
for general-purpose data storage if enMtl is clear.
enProtChksm: Enable protector checksum function.
x: Don't care.
nNVCfg2 Register (1BAh)
Register Type: Special
Factory Default Value: BE2Dh
Nonvolatile Restore: There is no associated restore location for this register
The nNVCfg2 register manages nonvolatile memory backup and restore of device and fuel gauge register RAM locations.
Each bit of the nNVCfg2 register, when set, enables a given register location to be restored from or backed up to a
corresponding nonvolatile memory location after reset of the IC. If nonvolatile backup of a given register is not enabled,
that location initializes to a default value after reset instead. See the individual register descriptions for details. Table 70
shows the nNVCfg2 register format.
Table 70. nNVCfg2 Register (1BAh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4 D3 D2 D1 D0
FibMax FibScl
enT
0
enMMT
enMMV
enMMC
enVT
enFC
0
enMet
0
enFL
FibMax/FibScl: Set the FibMax and FibScl "Fibonacci Saving" interval to provide recurring log-saving according to the
expected battery lifespan. See the 100 Record Life Logging section for more details.
enFL: Fault Logging. Set EnFL to store protector faults into nFaultLog.LowByte as shown in Table 46. EnFL is not
compatible with Age Forecasting. nFaultLog can be used as general-purpose memory if not used for fault logging or age
forecasting.
enFC: Enable FullCap and FullCapRep backup and restore. Set this bit to enable FullCap and FullCapRep registers to
be restored after reset by the nFullCapRep register and FullCapRep to backup to nFullCapRep. When this bit is clear
FullCap and FullCapRep registers restore from the nFullCapNom register. nFullCapRep can then be used as general-
purpose user memory.
enMMC: Enable MaxMinCurr Backup. Set this bit to enable storage of MaxMinCurr register information into the
nMaxMinCurr register during save operations. When this bit is clear nMaxMinCurr can be used as general-purpose
memory.
enMMV: Enable MaxMinVolt Backup. Set this bit to enable storage of MaxMinVolt register information into the
nMaxMinVolt register during save operations. When this bit is clear nMaxMinVolt can be used as general-purpose
memory.
enMMT: Enable MaxMinTemp Backup. Set this bit to enable storage of MaxMinTemp register information into the
nMaxMinTemp register during save operations. EnMMT is incompatible with nNVCFG2.enFL. When enMMT and enFL
bits are clear, nMaxMinTemp can be used as general-purpose memory.
enT: Enable TimerH backup and restore. Set this bit to enable TimerH register to be backed up and restored by the
nTimerH register. When this bit is clear TimerH restores with its alternate initialization value and nTimerH can be used
as general-purpose memory.
enVT: Enable Voltage and Temperature backup. Set this bit to enable storage of AvgVCell and AvgTA register
information into the nVoltTemp register during save operations. When this bit and nNVCfg0.enAF are clear nVoltTemp
can be used as general-purpose memory. Note that enVT should not be set simultaneously with nNVCfg0.enAF
(AgeForecasting) and nNVCfg2.enFL (Fault Logging).
enMet: Enable metal current sensing. Setting this bit to 1 enables temperature compensation of current readings
for allowing copper trace current sensing. See also nNVCfg1.enMtl, which enables nTCurve register operation for
adjustment of the current sensing temperature coefficient.
www.maximintegrated.com
Maxim Integrated | 110
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
nHibCfg Register (1BBh)
Register Type: Special
Factory Default Value: 0909h
Nonvolatile Restore: None
The nHibCfg register controls hibernate mode functionality. The IC enters hibernate mode, if the measured system
current falls below the HibThreshold setting for longer than the HibEnterTime delay. While in hibernate mode the IC
reduces its operating current by slowing down its task period as defined by the HibScalar setting. The IC automatically
returns to active mode of operation if current readings go above the HibThreshold setting for longer than the HibExitTime
delay. Table 71 shows the register format.
Table 71. nHibCfg Register (1BBh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
EnHib
HibEnterTime
HibThreshold
0
0
0
HibExitTime
HibScalar
0: Bit must be written 0. Do not write 1.
HibScalar: Sets the task period while in hibernate mode based on the following equation:
(HibScalar)
Hibernate Mode Task Period(s) = 702ms x 2
HibExitTime: Sets the required time period of consecutive current readings above the HibThreshold value before the IC
exits hibernate and returns to active mode of operation.
(HibScalar)
Hibernate Mode Exit Time(s) = (HibExitTime + 1) x 702ms x 2
HibThreshold: Sets the threshold level for entering or exiting hibernate mode. The threshold is calculated as a fraction
of the full capacity of the cell using the following equation:
(HibThreshold)
Hibernate Mode Threshold(mA) = (FullCap(mAh)/0.8hr)/2
HibEnterTime: Sets the time period that consecutive current readings must remain below the HibThreshold value before
the IC enters hibernate mode as defined by the following equation. The default HibEnterTime value of 000b causes the
IC to enter hibernate mode if all current readings are below the HibThreshold for a period of 5.625 seconds, but the IC
could enter hibernate mode as quickly as 2.812 seconds.
(HibEnterTime)
(HibEnterTime + 1)
2.812s x 2
< Hibernate Mode Entry Time < 2.812s x 2
EnHib: Enable Hibernate Mode. When set to 1, the IC enters hibernate mode if conditions are met. When set to 0, the
IC always remains in active mode of operation.
nFilterCfg Register (19Dh)
Register Type: Special
Nonvolatile Restore: FilterCfg (029h) if nNVCfg0.enFCfg is set.
Alternate Initial Value: 0EA4h
The nFilterCfg register sets the averaging time period for all ADC readings, for mixing OCV results, and coulomb count
results. It is recommended that these values are not changed unless absolutely required by the application. Table 72
shows the nFilterCfg register format.
Table 72. FilterCfg (029h)/nFilterCfg (19Dh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
TEMP
MIX
VOLT
CURR
CURR: Sets the time constant for the AvgCurrent register. The default POR value of 0100b gives a time constant of
5.625s. The equation setting the period is:
(CURR-7)
AvgCurrent time constant = 45s x 2
VOLT: Sets the time constant for the AvgVCell register. The default POR value of 010b gives a time constant of 45.0s.
www.maximintegrated.com
Maxim Integrated | 111
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
The equation setting the period is:
(VOLT-2)
AvgVCell time constant = 45s x 2
MIX: Sets the time constant for the mixing algorithm. The default POR value of 1101b gives a time constant of 12.8
hours. The equation setting the period is:
(MIX-3)
Mixing Period = 45s x 2
TEMP: Sets the time constant for the AvgTA register. The default POR value of 0001b gives a time constant of 1.5
minutes. The equation setting the period is:
TEMP
AvgTA time constant = 45s x 2
0: Write these bits to 0.
nMiscCfg Register (1B2h)
Register Type: Special
Nonvolatile Restore: MiscCfg (00Fh) if nNVCfg0.enMC is set
Alternate Initial Value: 0x3070
The nMiscCfg control register enables various other functions of the device. The nMiscCfg register default values should
not be changed unless specifically required by the application. Table 73 shows the register format.
Table 73. MiscCfg (00Fh)/nMiscCfg (1B2h) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
FUS
0
0
MR
1
0
0
SACFG
0: Bit must be written 0. Do not write 1.
1: Bit must be written 1. Do not write 0.
SACFG: SOC Alert Config. SOC Alerts can be generated by monitoring any of the SOC registers as follows. SACFG
defaults to 00 at power-up:
● 00: SOC Alerts are generated based on the RepSOC register.
● 01: SOC Alerts are generated based on the AvSOC register.
● 10: SOC Alerts are generated based on the MixSOC register.
● 11: SOC Alerts are generated based on the VFSOC register.
MR: Mixing Rate. This value sets the strength of the servo mixing rate after the final mixing state has been reached
(> 2.08 complete cycles). The units are MR0 = 6.25μV, giving a range up to 19.375mA with a standard 0.010Ω sense
resistor. Setting this value to 00000b disables servo mixing and the IC continues with time-constant mixing indefinitely.
The default setting is 18.75μV or 1.875mA with a standard sense resistor.
FUS: Full Update Slope. This field prevents jumps in the RepSOC and FullCapRep registers by setting the rate of
adjustment of FullCapRep near the end of a charge cycle. The update slope adjustment range is from 2% per 15 minutes
(0000b) to a maximum of 32% per 15 minutes (1111b).
nRelaxCfg Register (1B6h)
Register Type: Special
Nonvolatile Restore: RelaxCfg (0A0h) if nNVCfg0.enRCfg is set.
Alternate Initial Value: 0x2039
The nRelaxCfg register defines how the IC detects if the cell is in a relaxed state. See Figure 27. For a cell to be
considered relaxed, current flow through the cell must be kept at a minimum while the change in the cell’s voltage over
time, dV/dt, shows little or no change. If AvgCurrent remains below the LOAD threshold while VCell changes less than the
dV threshold over two consecutive periods of dt, the cell is considered relaxed. Table 74 shows the nRelaxCfg register
format.
www.maximintegrated.com
Maxim Integrated | 112
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 74. RelaxCfg (0A0h)/nRelaxCfg (1B6h) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
LOAD
dV
dt
LOAD: Sets the threshold, which the AvgCurrent register is compared against. The AvgCurrent register must remain
below this threshold value for the cell to be considered unloaded. Load is an unsigned 7-bit value where 1 LSb = 50μV.
The default value is 800μV.
dV: Sets the threshold, which VCell is compared against. If the cell’s voltage changes by less than dV over two
consecutive periods set by dt, the cell is considered relaxed; dV has a range of 0 to 40mV where 1 LSb = 1.25mV. The
default value is 3.75mV.
dt: Sets the time period over which change in VCell is compared against dV. If the cell’s voltage changes by less than dV
over two consecutive periods set by dt, the cell is considered relaxed. The default value is 1.5 minutes. The comparison
period is calculated as:
(dt-8)
Relaxation period = 2
x 45s
0
RELAXATION LOAD THRESHOLD
CURRENT
DISCHARGING
CELL UNLOADED
(RELAXATION BEGINS)
dV 6
dV 5
dV 4
CELL
dV 3
VOLTAGE
dV 2
48-96
MINUTES
dt 1
dt 2
dt 3
dt 4
dt 5
dt 6
Figure 27. Cell Relaxation Detection
www.maximintegrated.com
Maxim Integrated | 113
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
nLearnCfg Register (19Fh)
Register Type: Special
Nonvolatile Restore: LearnCfg (0A1h) if nNVCfg0.enLCfg is set
Alternate Initial Value: 0x4686
The nLearnCfg register controls all functions relating to adaptation during operation. Table 75 shows the register format:
Table 75. LearnCfg (0A1h)/nLearnCfg (19Fh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
1
0
0
0
1
1
0
1
LS
0
1
1
0
0: Bit must be written 0. Do not write 1.
1: Bit must be written 1. Do not write 0.
LS: Learn Stage. The Learn Stage value controls the influence of the voltage fuel gauge on the mixing algorithm. Learn
Stage defaults to 0h, making the voltage fuel gauge dominate. Learn Stage then advances to 7h over the course of two
full cell cycles to make the coulomb counter dominate. Host software can write the Learn Stage value to 7h to advance
to the final stage at any time. Writing any value between 1h and 6h is ignored.
nTTFCfg Register (1C7h)/CVMixCap (0B6h) and CVHalfTime (0B7h) Registers
Register Type: Special
Nonvolatile Restore: CVHalfTime (0B7h) and CVMixCapRatio (0B6h) if nNVCfg1.enTTF is set.
Alternate Initial Value: CVHalfTime = 0xA00 (30 minutes) and CVMixCap = 75% x FullCapNom.
The nTTFCfg register configures parameters related to the time-to-full (TTF) calculation. If nNVCfg1.enTTF is set,
CVHalfTime (0B7h) and CVMixCapRatio (0B6h) are refreshed from the nTTFCfg Register.
CVHalfTime (0B7h) is defined as the amount of time in the constant voltage portion of the charge cycle for the current to
taper to half of the charging current in the constant current portion of the charge cycle. See Figure 28. CVHalfTime has
an LSB of 0.0001953125 hours.
CVMixCapRatio (0B6h) is defined as the approximate state of charge where the charge transitions from the constant
current portion of the charge cycle to the constant voltage portion of the charge current. See Figure 28. CVMixCapRatio
has an LSB of 0.5mAh.
The Alternate Initial Value indicates that the charge cycle transitions from constant current to constant voltage when the
SOC is 75% and that it then takes 30 minutes for the current to taper half of the charging current.
www.maximintegrated.com
Maxim Integrated | 114
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
CHARGING CURRENT
CURRENT
READING
CHARGING CURRENT / 2
HALFTIME
CONSTANT
CURRENT
CHARGE
CONSTANT
VOLTAGE
CHARGE
FULLCAPNOM
PACK
CAPACITY
MIXCAP
MIXCAPRATIO =
MIXCAP/FULLCAPNOM
Figure 28. TTF Configuration Diagram
The nTTFCfg parameters can be tuned for best TTF performance during characterization by Maxim. Table 76 shows the
register format.
Table 76. nTTFCfg Register (1C7h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
nCVHalfTime
nCVMixCapRatio
nCVHalfTime: nCVHalfTime has an LSB of 45 seconds giving a full scale range of 0 seconds to 192 minutes.
nCVHalfTime = CVHalfTime(s)/45 seconds
nCVMixCapRatio: nCVMixCapRatio has an LSB of 1/256 giving a full scale range of 0 to 0.9961.
nCVMixCapRatio = CVMixCapRatio(%) × 256
For example, for a nCVHalftime of 37.5 minutes (2250 seconds) and a nCVMixRatio of 59%, the value for nTTFCfg =
3297h. These values are calculated as follows:
nCVHalfTime = 2250s/45 = 50dec = 32h
nCVMixCapRatio = 59% x 256 = 151dec = 97h
nConvgCfg Register (1B7h)
Register Type: Special
Factory Default Value: 2241h
Nonvolatile Restore: There is no associated restore location for this register.
The nConvgCfg register configures operation of the converge-to-empty feature. Table 77 shows the nConvgCfg register
www.maximintegrated.com
Maxim Integrated | 115
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
format. The nNVCfg1.CTE bit must be set to enable converge-to-empty functionality. If nNVCfg1.CTE is clear, this
register can be used as general-purpose data storage.
Table 77. nConvgCfg Register (1B7h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RepLow
VoltLowOff
MinSlopeX
RepL_per_stage
RepL_per_stage: Adjusts the RepLow threshold setting depending on the present learn stage using the following
equation. This allows the RepLow threshold to be at higher levels for earlier learn states. RepL_per_stage has an LSb of
1% giving a range of 0% to 7%.
RepLow Threshold = RepLow Field Setting + RemainingStages x RepL_per_stage
MinSlopeX: Sets the amount of slope shallowing which occurs when RepSOC falls below RepLow. MinSlopeX LSb
corresponds to a ratio of 1/16 giving a full range of 0 to 15/16.
VoltLowOff: When the AvgVCell register value drops below the VoltLow threshold, RepCap begins to bend downwards
by a ratio defined by the following equation. VoltLowOff has an LSb of 20mV giving a range of 0 to 620mV.
(AvgVCell - VEmpty)/VoltLowOff
RepLow: Sets the threshold below which RepCap begins to bend upwards. The RepLow field LSb is 2% giving a full
scale range from 0% to 30%.
nRippleCfg Register (1B1h)
Register Type: Special
Factory Default Value: 0204h
Nonvolatile Restore: There is no associated restore location for this register.
The nRippleCfg register configures ripple measurement and ripple compensation. The recommended value for this
register is 0x0204. Table 78 shows the register format.
Table 78. nRippleCfg Register (1B1h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
kDV
NR
NR: Sets the filter magnitude for ripple observation as defined by the following equation giving a range of 1.4 seconds to
180 seconds.
NR
Ripple Time Range = 1.4 seconds x 2
kDV: Sets the corresponding amount of capacity to compensate proportional to the ripple.
SOCHold Register (0D0h)
Register Type: Special
The SOCHold register configures operation of the hold before empty feature and also the enable bit for 99% hold during
charge. The default value for SOCHold is 1002h. Table 79 shows the SOCHold register format.
Table 79. SOCHold (0D0h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
99%HoldEn
EmptyVoltHold
EmptySocHold
EmptyVoltHold: The positive voltage offset that is added to VEmpty. At VCell = VEmpty + EmptyVoltHold point, the
empty detection/learning is occured. EmptyVoltHold has an LSb of 10mV giving a range of 0 to 1270mV.
EmptySocHold: It is the RepSOC at which RepSOC is held constant. After empty detection/learning occurs, RepSOC
update continues as expected. EmptySocHold has an LSb of 0.5%, giving it a full range of 0 to 15.5%.
www.maximintegrated.com
Maxim Integrated | 116
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
99%HoldEn: Enable bit for 99% hold feature during charging. When enabled, RepSOC holds a maximum value of 99%
until Full Qualified is reached.
ModelGauge m5 Algorithm Additional Registers
The following registers contain intermediate ModelGauge m5 data which may be useful for debugging or performance
analysis. The values in these registers are reset to their initial values 480ms after the IC is reset.
QResidual Register (00Ch)
Register Type: Capacity
Nonvolatile Backup: None
The QResidual register displays the calculated amount of charge in mAh that is presently inside of, but cannot be
removed from the cell under present application conditions. This value is subtracted from the MixCap value to determine
the capacity available to the user under present conditions (AvCap).
VFSOC Register (0FFh)
Register Type: Percentage
Nonvolatile Backup: None
The VFSOC register holds the calculated present state-of-charge of the battery according to the voltage fuel gauge.
VFOCV Register (0FBh)
Register Type: Voltage
Nonvolatile Backup: None
The VFOCV register contains the calculated open-circuit voltage of the cell as determined by the voltage fuel gauge. This
value is used in other internal calculations.
QH Register (4Dh)
Register Type: Capacity
Nonvolatile Backup: None
Alternate Initial Value: 0x0000
The QH register displays the raw coulomb count generated by the device. This register is used internally as an input to
the mixing algorithm. Monitoring changes in QH over time can be useful for debugging device operation.
AvCap Register (01Fh)
Register Type: Capacity
Nonvolatile Backup: None
The AvCap register holds the calculated available capacity of the cell pack based on all inputs from the ModelGauge m5
algorithm including empty compensation. The register value is an unfiltered calculation. Jumps in the reported value can
be caused by changes in the application such as abrupt changes in load current or temperature. See the Fuel-Gauge
Empty Compensation section for details.
www.maximintegrated.com
Maxim Integrated | 117
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
AvSOC Register (00Eh)
Register Type: Percentage
Nonvolatile Backup: None
The AvSOC register holds the calculated available state of charge of the cell based on all inputs from the ModelGauge
m5 algorithm including empty compensation. The AvSOC percentage corresponds with AvCap and FullCapNom. The
AvSOC register value is an unfiltered calculation. Jumps in the reported value can be caused by changes in the
application such as abrupt changes in load current or temperature. See the Fuel-Gauge Empty Compensation section for
details.
MixSOC Register (00Dh)
Register Type: Percentage
Nonvolatile Backup: None
The MixSOC register holds the calculated present state-of-charge of the cell before any empty compensation
adjustments are performed. MixSOC corresponds with MixCap and FullCapNom. See the Fuel-Gauge Empty
Compensation section for details.
MixCap Register (02Bh)
Register Type: Capacity
Nonvolatile Backup: None
The MixCap register holds the calculated remaining capacity of the cell before any empty compensation adjustments are
performed. See the Fuel-Gauge Empty Compensation section for details.
VFRemCap Register (04Ah)
Register Type: Capacity
Nonvolatile Backup: None
The VFRemCap register holds the remaining capacity of the cell as determined by the voltage fuel gauge before any
empty compensation adjustments are performed. See the Fuel-Gauge Empty Compensation section for details.
FStat Register (03Dh)
Register Type: Special
Nonvolatile Backup: None
The FStat register is a read-only register that monitors the status of the ModelGauge algorithm. Do not write to this
register location. Table 80 is the FStat register format.
Table 80. FStat Register (03Dh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
RelDt
EDet
X
RelDt2
X
X
X
X
X
DNR
DNR: Data Not Ready. This bit is set to 1 at cell insertion and remains set until the output registers have been updated.
Afterwards, the IC clears this bit indicating the fuel gauge calculations are now up to date. This takes between 445ms
and 1.845s depending on whether the IC was in a powered state prior to the cell-insertion event.
RelDt2: Long Relaxation. This bit is set to 1 whenever the ModelGauge m5 algorithm detects that the cell has been
relaxed for a period of 48 to 96 minutes or longer. This bit is cleared to 0 whenever the cell is no longer in a relaxed state.
See Figure 31.
EDet: Empty Detection. This bit is set to 1 when the IC detects that the cell empty point has been reached. This bit is
reset to 0 when the cell voltage rises above the recovery threshold. See the VEmpty register for details.
www.maximintegrated.com
Maxim Integrated | 118
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
RelDt: Relaxed cell detection. This bit is set to 1 whenever the ModelGauge m5 algorithm detects that the cell is in a fully
relaxed state. This bit is cleared to 0 whenever a current greater than the load threshold is detected. See Figure 31.
X: Don’t Care. This bit is undefined and can be logic 0 or 1.
Identification Registers
The following registers contain information to identify the IC type and the specific ROM ID.
DevName Register (021h)
Register Type: Special
Nonvolatile Backup: None
The DevName register holds device type and firmware revision information. This allows the host software to easily
identify the type of IC being communicated to. Table 81 shows the DevName register format.
Table 81. DevName Register (021h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Revision
Device
The DevName for the IC is 0x4209.
nROMID0 (1BCh)/nROMID1 (1BDh)/nROMID2 (1BEh)/nROMID3 (1BFh) Registers
Register Type: Special
Nonvolatile Restore: There are no associated restore locations for these registers
Each IC contains a unique 64-bit identification value that is contained in the nROMID registers. Note this is the same ID
that can be read using the 1-Wire ROM ID commands. The unique ID can be reconstructed from the nROMID registers
as shown in Table 82.
Table 82. nROMID Registers (1BCh to 1BFh) Format
nROMID3[15:0]
nROMID2[15:0]
nROMID1[15:0]
nROMID0[15:0]
ROM ID [15:0]
ROM ID [63:48]
ROM ID [47:32]
ROM ID [31:16]
AtRate Functionality
The AtRate function allows the host software to see the theoretical remaining time or capacity for any given load
current. AtRate can be used for power management by limiting system loads depending on present conditions of the
cell pack. Whenever the AtRate register is programmed to a negative value indicating a hypothetical discharge current,
the AtQResidual, AtTTE, AtAvSOC, and AtAvCap registers display theoretical residual capacity, time-to-empty, state-of-
charge, and available capacity respectively. Host software should wait two full task periods (703ms minimum in active
mode) after writing the AtRate register before reading any of the result registers.
AtRate Register (004h)
Register Type: Current
Nonvolatile Backup: None
Host software should write the AtRate register with a negative two’s-complement 16-bit value of a theoretical load current
prior to reading any of the at-rate output registers.
AtQResidual Register (0DCh)
Register Type: Capacity
Nonvolatile Backup: None
The AtQResidual register displays the residual charge held by the cell at the theoretical load-current level entered into
the AtRate register.
www.maximintegrated.com
Maxim Integrated | 119
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
AtTTE Register (0DDh)
Register Type: Time
Nonvolatile Backup: None
The AtTTE register can be used to estimate time-to-empty for any theoretical current load entered into the AtRate
register. The AtTTE register displays the estimated time-to-empty for the application by dividing AtAvCap by the AtRate
register value. The AtTTE register has a maximum value of 102.3 hours. When AtTTE is larger than the maximum value,
the AtTTE register saturates and contains the maximum value (FFFFh). The host can calculate time values longer that
the maximum register value with the following equation:
AtTTE
(hours) = AtAvCap(mAh)/AtRate(mA)
CALCULATED
AtAvSOC Register (0CEh)
Register Type: Percentage
Nonvolatile Backup: None
The AtAvSOC register holds the theoretical state of charge of the cell based on the theoretical current load of the AtRate
register. The register value is stored as a percentage with a resolution of 0.0039% per LSB. If a 1% resolution state-of-
charge value is desired, the host can read only the upper byte of the register instead.
AtAvCap Register (0DFh)
Register Type: Capacity
Nonvolatile Backup: None
The AtAvCap register holds the estimated remaining capacity of the cell based on the theoretical load current value of
the AtRate register. The value is stored in terms of µVh and must be divided by the application sense-resistor value to
determine the remaining capacity in mAh.
Alert Function
The Alert Threshold registers allow interrupts to be generated by detecting a high or low voltage, current, temperature,
state-of-charge, or protection fault. Interrupts are generated on the ALRT pin open-drain output driver. An external pullup
is required to generate a logic-high signal. Alerts can be triggered by any of the following conditions:
● Over/undervoltage—VAlrtTr register threshold violation (upper or lower) and alerts enabled (Aen = 1).
● Over/undertemperature—TAlrtTr register threshold violation (upper or lower) and alerts enabled (Aen = 1).
● Over/undercurrent—IAlrtTr register threshold violation (upper or lower) and alerts enabled (Aen = 1).
● Over/under SOC—SAlrtTr register threshold violation (upper or lower) and alerts enabled (Aen = 1).
● Protection Alert—ProtAlrt indicates which protection fault occured. Protection alerts enabled (Config.PAen = 1) and
alerts enabled (Aen = 1).
To prevent false interrupts, the threshold registers should be initialized before setting the Aen bit. Alerts generated by a
threshold-level violation can be configured to be cleared only by software, or cleared automatically when the threshold
level is no longer violated. Prior to clearing the Status.PA, the ProtAlrt register must be written to 0000h. See the Config
(01Dh) register description for details of the alert function configuration.
nVAlrtTh Register (18Ch)
Register Type: Special
Nonvolatile Restore: VAlrtTh (001h) if nNVCfg1.enAT is set.
Alternate Initial Value: FF00h (Disabled)
The nVAlrtTh register shown in Table 83 sets upper and lower limits that generate an ALRT pin interrupt if exceeded by
any of the cell voltage readings. The upper 8 bits set the maximum value and the lower 8 bits set the minimum value.
Interrupt threshold limits are selectable with 20mV resolution over the full operating range of the VCell register. At power-
up, the thresholds default to their maximum settings unless they are configured to be restored from nonvolatile memory
instead by setting the nNVCfg1.enAT bit.
www.maximintegrated.com
Maxim Integrated | 120
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 83. VAlrtTh (001h)/nVAlrtTh (18Ch) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
VMAX
VMIN
VMAX: Maximum voltage reading. An alert is generated if the maximum cell voltage reading exceeds this value. This
field has 20mV LSb resolution.
VMIN: Minimum voltage reading. An alert is generated if the VCell register reading falls below this value. This field has
20mV LSb resolution.
nTAlrtTh Register (18Dh)
Register Type: Special
Nonvolatile Restore: TAlrtTh (002h) if nNVCfg1.enAT is set.
Alternate Initial Value: 7F80h (Disabled)
The nTAlrtTh register shown in Table 84 sets upper and lower limits that generate an ALRT pin interrupt if exceeded by
any thermistor reading. The upper 8 bits set the maximum value and the lower 8 bits set the minimum value. Interrupt
threshold limits are stored in 2’s-complement format with 1ºC resolution over the full operating range of the Temp register.
At power-up, the thresholds default to their maximum settings unless they are configured to be restored from nonvolatile
memory instead by setting the nNVCfg1.enAT bit.
Table 84. TAlrtTh (002h)/nTAlrtTh (18Dh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
TMAX
TMIN
TMAX: Maximum temperature reading. An alert is generated if any temperature channel reading exceeds this value. This
field is signed 2's complement format with 1ºC LSb resolution.
TMIN: Minimum temperature reading. An alert is generated if the Temp register reading falls below this value. This field
is signed 2's complement format with 1ºC LSb resolution.
nSAlrtTh Register (18Fh)
Register Type: Special
Nonvolatile Restore: SAlrtTh (003h) if nNVCfg1.enAT is set.
Alternate Initial Value: FF00h (Disabled)
The nSAlrtTh register shown in Table 85 sets upper and lower limits that generate an ALRT pin interrupt if exceeded
by the selected RepSOC, AvSOC, MixSOC, or VFSOC register values. See the MiscCFG.SACFG setting for details.
The upper 8 bits set the maximum value and the lower 8 bits set the minimum value. Interrupt threshold limits are
selectable with 1% resolution over the full operating range of the selected SOC register. At power-up, the thresholds
default to their maximum settings unless they are configured to be restored from nonvolatile memory instead by setting
the nNVCfg1.enAT bit.
Table 85. SAlrtTh (003h)/nSAlrtTh (18Fh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
SMAX
SMIN
SMAX: Maximum state-of-charge reading. An alert is generated if the selected SOC register reading exceeds this value.
This field has 1% LSb resolution.
SMIN: Minimum state-of-charge reading. An alert is generated if the selected SOC register reading falls below this value.
This field has 1% LSb resolution.
www.maximintegrated.com
Maxim Integrated | 121
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
nIAlrtTh Register (0ACh)
Register Type: Special
Nonvolatile Restore: IAlrtTh (0ACh) if nNVCfg1.enAT is set.
Alternate Initial Value: 7F80h (Disabled)
The nIAlrtTh register shown in Table 86 sets upper and lower limits that generate an ALRT pin interrupt if exceeded by
the Current register value. The upper 8 bits set the maximum value and the lower 8 bits set the minimum value. Interrupt
threshold limits are selectable with 400μV resolution over the full operating range of the Current register. At power-up, the
thresholds default to their maximum settings unless they are configured to be restored from nonvolatile memory instead
by setting the nNVCfg1.enAT bit.
Table 86. IAlrtTh (0ACh)/nIAlrtTh (18Eh) Register Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CURRMAX
CURRMIN
CURRMAX: Maximum Current Threshold. An alert is generated if the current register reading exceeds this value. This
field is signed 2's complement with 400μV LSb resolution to match the upper byte of the Current register.
CURRMIN: Minimum Current Threshold. An alert is generated if the current register reading falls below this value. This
field is signed 2's complement with 400μV LSb resolution to match the upper byte of the Current register.
www.maximintegrated.com
Maxim Integrated | 122
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Memory
The memory space of the IC consists of 32 pages of 16 registers which are 16-bits wide. Registers are addressed using
an internal 9-bit range of 000h to 1FFh. Externally, registers are accessed with an 8-bit address for 2-wire communication
or 16-bit address for 1-Wire communication. Registers are grouped by functional block. See the functional descriptions for
details of each register's functionality. Certain memory blocks can be permanently locked to prevent accidental overwrite.
See the Locking Memory Blocks section for details. Table 87 shows the full memory map of the IC. Note that some
individual user registers are located on RESERVED memory pages. These locations can be accessed normally while the
remainder of the page is considered RESERVED. Memory locations listed as RESERVED should never be written to.
Data read from RESERVED locations is not defined.
Table 87. Top Level Memory Map
2-WIRE
REGISTER
PAGE
SLAVE
ADDRESS
2-WIRE
PROTOCOL
2-WIRE EXTERNAL
ADDRESS RANGE
1-WIRE EXTERNAL
ADDRESS RANGE
LOCK
—
DESCRIPTION
00h
MODELGAUGE m5
DATA BLOCK
2
6Ch
—
I C
00h–4Fh
—
0000h–004Fh
—
01h–04h
05h–0Ah
LOCK2
—
RESERVED
—
MODELGAUGE m5
LOCK2 DATA BLOCK
(continued)
2
0Bh
0Ch
0Dh
6Ch
6Ch
6Ch
I C
B0h–BFh
C0h–CFh
D0h–DFh
00B0h–00BFh
00C0h–00CFh
00D0h–00DFh
2
SHA
SHA MEMORY
I C
MODELGAUGE m5
LOCK2 DATA BLOCK
(continued)
2
I C
0Eh–0Fh
10h–17h
18h–19h
—
—
RESERVED
—
—
—
—
—
SBS DATA BLOCK
16h
SBS
00h–7Fh
LOCK3
1Ah–1Bh LOCK1
NONVOLATILE
MEMORY
16h
16h
2
1Ch
1Dh
1Eh
LOCK4
LOCK5
LOCK1
I C
80h–EFh
F0h–FFh
0180h–01EFh
01F0h–01FFh
NONVOLATILE
HISTORY
2
1Fh
—
I C
Table 88. Individual Registers
REGISTER
ADDRESS
2-WIRE SLAVE
ADDRESS
2-WIRE
PROTOCOL
2-WIRE EXTERNAL
ADDRESS RANGE
1-WIRE EXTERNAL
ADDRESS RANGE
LOCK DESCRIPTION
Command
Register
2
060h
—
6Ch
I C
60h
0060h
CommStat
Register
2
061h
07Fh
—
6Ch
6Ch
I C
61h
7Fh
0061h
007Fh
2
—
Lock Register
I C
www.maximintegrated.com
Maxim Integrated | 123
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
ModelGauge m5 Memory Space
Registers that relate to functionality of the ModelGauge m5 fuel gauge are located on pages 00h–04h and are continued
on pages 0Bh and 0Dh. See the ModelGauge m5 Algorithm section for details of specific register operation. These
locations (other than page 00h) can be permanently locked by setting LOCK2. Register locations shown in gray are
reserved locations and should not be written to. See Table 89.
Table 89. ModelGauge m5 Register Memory Map
PAGE/
00_h
01_h
02_h
03_h
04_h
0A_h
0B_h
0D_h
WORD
0h
1h
2h
3h
4h
5h
6h
7h
Status
VAlrtTh
TAlrtTh
SAlrtTh
AtRate
RepCap
RepSOC
Age
FullCapRep
TTE
TTF
Reserved
Reserved
AvgDieTemp
Reserved
RelaxCfg
LearnCfg
Status2
Power
SOCHold
AvgCell4
AvgCell3
AvgCell2
AvgCell1
CELL4
DevName
QRTable00 QRTable10 QRTable20 QRTable30
Reserved
VRipple
FullSocThr FullCapNom
Reserved
DieTemp
FullCap
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
AvgPower
Reserved
TTFCfg
RCell
Reserved
AvgTA
Reserved
Reserved
Reserved
Reserved
MaxPeakPower
SusPeakPower
PackResistance
SysResistance
IAvgEmpty
Reserved
CVMixCap
CVHalfTime
CELL3
Cycles
CELL2
Charging
Current
8h
9h
Ah
MaxMinVolt
MaxMinTemp
MaxMinCurr
DesignCap
AvgVCell
VCell
Reserved
Reserved
VEmpty
Reserved
Reserved
MinSysVoltage
MPPCurrent
SPPCurrent
CGTempCo
AgeForecast
Reserved
CELL1
ProtStatus
Batt
FilterCfg
Charging
Voltage
VFRemCap
Bh
Ch
Dh
Eh
Fh
Config
QResidual
MixSOC
AvSOC
Temp
Current
MixCap
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
FStat
Reserved
Reserved
QH
Config2
IAlrtTh
Reserved
Reserved
Reserved
TimerH
PCKP
AtQResidual
AtTTE
AvgCurrent
IChgTerm
AvCap
MinVolt
MinCurr
ProtAlrt
Timer
QL
AtAvSOC
AtAvCap
MiscCfg
Reserved
Reserved
Reserved
www.maximintegrated.com
Maxim Integrated | 124
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Nonvolatile Memory
Nonvolatile Memory Map
Certain ModelGauge m5 and device configuration values are stored in nonvolatile memory to prevent data loss if the IC
loses power. The IC internally updates page 1Ah values over time based on actual performance of the ModelGauge m5
algorithm. The host system does not need to access this memory space during operation. Nonvolatile data from other
accessible register locations is internally mirrored into the nonvolatile memory block automatically. Note that nonvolatile
memory has a limited number of writes. User accessible configuration memory is limited to 7 writes. Internal and
external updates to page 1Ah as the fuel gauge algorithm learns is limited to 100 writes. Do not exceed these
write limits. See Table 96 for details on configuring the logging interval. Table 90 shows the nonvolatile memory register
map.
Table 90. Nonvolatile Register Memory Map (slave address 16h)
PAGE/
1
18_h
19_h
1A_h
1B_h
1C_h
1D_h
1E_h
WORD
0h
1h
2h
3h
4h
5h
6h
7h
8h
9h
Ah
Bh
Ch
Dh
Eh
Fh
nXTable0
nXTable1
nXTable2
nXTable3
nXTable4
nXTable5
nXTable6
nXTable7
nXTable8
nXTable9
nOCVTable0
nOCVTable1
nOCVTable2
nOCVTable3
nOCVTable4
nOCVTable5
nOCVTable6
nOCVTable7
nOCVTable8
nOCVTable9
nQRTable00
nQRTable10
nQRTable20
nQRTable30
nCycles
nConfig
nRippleCfg
nMiscCfg
nDesignCap
nSBSCfg
nPackCfg
nRelaxCfg
nConvgCfg
nNVCfg0
nNVCfg1
nNVCfg2
nHibCfg
nPReserved0
nPReserved1
nChgCfg
nUVPrtTh
nTPrtTh1
nTPrtTh3
nIPrtTh1
nDPLimit
nScOcvLim
nAgeFcCfg
nChgCtrl
nDesignVoltage
Reserved
nRGain
nBALTh
nFullCapNom
nRComp0
nPackResistance
nFullSOCThr
nTTFCfg
nTPrtTh2
nProtMiscTh
nProtCfg
Reserved
nManfctrDate
nFirstUsed
nTempCo
nBattStatus
nFullCapRep
nVoltTemp
nCGain
nJEITAC
nJEITAV
nSerialNumber0
nSerialNumber1
nSerialNumber2
nDeviceName0
nDeviceName1
nDeviceName2
nDeviceName3
nDeviceName4
nCGTempCo
nThermCfg
Reserved
nXTable10 nOCVTable10
nXTable11 nOCVTable11
nOVPrtTh
nStepChg
nDelayCfg
nODSCTh
nODSCCfg
nProtCfg2
nMaxMinCurr
nMaxMinVolt
nMaxMinTemp
2
nVAlrtTh
nTAlrtTh
nIAlrtTh
nSAlrtTh
nIChgTerm
nFilterCfg
nVEmpty
nROMID0
nManfctrName0
nManfctrName1
nManfctrName2
nRSense
2
nROMID1
2
nFaultLog/ nFullCapFlt nROMID2
2
nLearnCfg
nTimerH
nROMID3
1. Locations 1A0h to 1AFh are updated automatically by the IC each time it learns.
2. The ROM ID is unique to each IC and cannot be changed by the user.
Shadow RAM
Nonvolatile memory is never written to or read from directly by the communication interface. Instead, data is written to
or read from shadow RAM memory located at the same address. Copy and recall commands are used to transfer data
between the nonvolatile memory and the shadow RAM. Figure 29 describes this relationship. Nonvolatile memory recall
occurs automatically at IC power-up and software POR.
www.maximintegrated.com
Maxim Integrated | 125
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Shadow RAM and Nonvolatile Memory Relationship
SHADOW RAM
0180h
NONVOLATILE MEMORY
0180h
DATA WRITE
COPY NV BLOCK
NV RECALL
DATA READ
01EFh
01EFh
Figure 29. Shadow RAM and Nonvolatile Memory Relationship
Nonvolatile Memory Commands
The following commands are used to copy or recall data from the nonvolatile memory. All commands are written to the
Command register at memory address 060h to perform the desired operation. The CommStat register can be used to
track the status of the request.
COPY NV BLOCK [E904h]
This command copies the entire block from shadow RAM to nonvolatile memory addresses 180h to 1EFh excluding
the unique ID locations of 1BCh to 1BFh. After issuing this command, the host must wait t
for the operation to
BLOCK
complete. The configuration memory can be copied a maximum of seven times. Note that the supply voltage must be
above V for the operation to complete successfully.
NVM
NV RECALL [E001h]
This command recalls the entire block from nonvolatile memory to Shadow RAM addresses 180h to 1EFh. This is a
low-power operation that takes up to t
operation to complete successfully.
to complete. Note that the supply voltage must be above V
for the
NVM
RECALL
HISTORY RECALL [E2XXh]
This command copies history data into page 1Fh of the memory. After issuing this command, the host must wait t
RECALL
for the operation to complete before reading page 1Fh. Table 91 shows the history information that can be recalled.
See the SHA-256, Battery Life Logging, and Determining Number of Remaining Updates sections for details on how to
decode this information.
www.maximintegrated.com
Maxim Integrated | 126
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 91. History Recall Command Functions
COMMAND
FUNCTION
0xE29D
Recall indicator flags to determine remaining SHA-256 secret updates or clears
Recall indicator flags to determine remaining configuration memory writes
Recall indicator flags to determine remaining Battery Life Logging updates
Recall indicator flags to determine Battery Life Logging update errors
Recall Battery Life Logging information
0xE29B
0xE29C
0xE29C, 0xE29D
0xE22E to 0xE291
Nonvolatile Block Programming
The host must program all nonvolatile memory locations at the same time by using the Copy NV Block command.
After clearing the write protection bits, the host writes all desired nonvolatile memory Shadow RAM locations to their
desired values, then sends the Copy NV Block command, and then waits t
for the copy to complete. The
BLOCK
CommStat.NVError bit should be read to determine if the copy command executed successfully. Afterwards, the host
should send the power-on-reset sequence to reset the IC and have the new nonvolatile settings take effect. Note that the
configuration memory is limited to n
total write attempts. The recommended full sequence is as follows:
BLOCK
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Write desired memory locations to new values.
3. Write 0x0000 to the CommStat register (0x61) one more time to clear CommStat.NVError bit.
4. Write 0xE904 to the Command register 0x060 to initiate a block copy.
5. Wait t
for the copy to complete.
BLOCK
6. Check the CommStat.NVError bit. If set, repeat the process. If clear, continue.
7. Write 0x000F to the Command register 0x060 to send the full reset command to the IC.
8. Wait 10ms for the IC to reset. Write protection resets after the full reset command.
9. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
10. Write 0x8000 to the Config2 register 0x0AB to reset firmware.
11. Wait for the POR_CMD bit (bit 15) of the Config2 register to be cleared to indicate that the POR sequence is
complete.
12. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
Determining Number of Remaining Updates
The configuration memory can only be updated seven times by the user (first update occurs during the manufacturing
test). The number of remaining updates can be calculated using the following procedure:
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Write 0xE29B to the Command register (060h).
3. Wait t
.
RECALL
4. Read memory address 1FDh.
5. Decode address 1FDh data as shown in Table 92. Each block write has redundant indicator flags for reliability.
Logically OR the upper and lower bytes together then count the number of 1s to determine how many updates have
already been used. The first update occurs in the manufacturing test prior to shipping to the user.
6. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
www.maximintegrated.com
Maxim Integrated | 127
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 92. Number of Remaining Config Memory Updates
ADDRESS 1FDH
DATA
LOGICAL OR OF UPPER AND LOWER
BYTES
NUMBER OF UPDATES
USED
NUMBER OF UPDATES
REMAINING
0000000x00000001b
or
00000001b
00000011b
00000111b
00001111b
00011111b
00111111b
01111111b
11111111b
1
2
3
4
5
6
7
8
7
6
5
4
3
2
1
0
000000010000000xb
000000xx0000001xb
or
0000001x000000xxb
00000xxx000001xxb
or
000001xx00000xxxb
0000xxxx00001xxxb
or
00001xxx0000xxxxb
000xxxxx0001xxxxb
or
0001xxxx000xxxxxb
00xxxxxx001xxxxxb
or
001xxxxx00xxxxxxb
0xxxxxxx01xxxxxxb
or
01xxxxxx0xxxxxxxb
xxxxxxxx1xxxxxxxb
or
1xxxxxxxxxxxxxxxb
Enabling and Freeing Nonvolatile vs. Defaults
There are seven nonvolatile memory words labeled nUser that are dedicated to general-purpose user data storage. Most
other nonvolatile memory locations can also be used as general-purpose storage if their normal function is disabled. The
nNVCfg0, nNVCfg1, and nNVCfg2 registers control which nonvolatile memory functions are enabled and disabled. Table
94 shows how to free up the specific registers for user data storage. Table 95 shows which nNVCfg bits control different
IC functions and the effects when the bit is set or cleared. See the nNVCfg register descriptions for complete details. Do
not convert a nonvolatile register to general-purpose memory space if that register's function is used by the application.
Table 93 is a summary of how many bytes can be made available for user memory and the functional trade-off to free up
those bytes.
Table 93. Total Bytes Freeable for User Memory
BYTES
DESCRIPTION
FREEABLE
164
132
84
Maximum freeable when protector is disabled and EZ Model is used.
When using protector and EZ Model.
When using protector and custom model.
66
When using protector, custom model, and half of the miscellaneous configuration options.
When using protector, custom model, and all of the miscellaneous configuration options.
When using protector, custom model, all of the miscellaneous configuration options, and alerts.
48
40
www.maximintegrated.com
Maxim Integrated | 128
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 93. Total Bytes Freeable for User Memory (continued)
BYTES
DESCRIPTION
FREEABLE
When using protector, custom model, all of the miscellaneous configuration options, alerts, and backup
enabled.
28
28
Always free when SBS mode is not enabled.
Table 94. Making Nonvolatile Memory Available for User Data
RELATED
FEATURE
FREE BY
BYTES
REGISTERS
ADDRESS
COMMENTS
Disable SBS and
DS features
nNVCfg0.enSBS words
= 0 30
nNVCfg1.enDS = bytes
0
nManfctrName[0:2]
nDesignVoltage
nManfctrDate
nFirstUsed
nSerialNumber[0:2]
nDeviceName[0:4]
15
1CCh–CEh,
1E3h,
1E6h–1EFh
SBS NVM
Generally freeable.
Time-to-Full
Configurability = 0
nNVCfg1.enTTF 1 word
Free if default nTTFCfg is
acceptable.
nTTFCfg
nDPLimit
1C7h
1E0h
2 bytes
nNVCfg0.enDP = 1 word
2 bytes
Dynamic
Power
MAJOR
FEATURE
CHOICES
Free if feature is not used.
0
Free if feature is not used.
Has additional implications
with nVoltTemp.
Age
Forecasting
nNVCfg0.enAF = 1 word
0 2 bytes
nAgeFcCfg
nScOcvLim
1E2h
1E1h
nNVCfg1.enSC = 1 word
LiFePO
Free if feature is not used.
4
0
2 bytes
JEITA Charge
Voltage/
Current vs.
Temp
Free if feature is not used.
Note that nJEITAV and
nOVPrtTh are still required
for protector functionality.
nNVCfg0.enJ = 0
2
nJEITAC
nStepChg
1D8h,
1DBh
nNVCfg0.enJP = words
4 bytes
0
Freeable when original full-
capacity is not required to
be remembered as
Design Cap + nNVCfg0.enDC
1 word nDesignCap
2 bytes (else nFullCapRep)
1B3h
FullCapRep
= 0
FullCapRep ages.
Relaxation
Configuration = 0
nNVCfg0.enRCfg
nRelaxCfg
1B6h
1B2h
Miscellaneous nNVCfg0.enMC
Configuration = 0
nMiscCfg
Converge-to-
Empty Non-
Default
6
MODELLING/
CHARACTER-
IZATION
CONFIGURATION
OPTIONS
nNVCfg1.enCTE words
Normally freeable. Defaults
work for most applications.
nConvgCfg
12
1B7h
= 0
Configuration
bytes
Full Detection nNVCfg1.enFTh
% Threshold
nFullSOCTh
1C6h
19Dh
19Fh
= 0
Filter
Configuration
nNVCfg0.enFC =
0
nFilterCfg
1 word
Freeable depending on
modelling/characterization.
nLearnCfg
nNVCfg0.en = 0
nLearnCfg
2 bytes
Free if targeting the fuel
gauge to default 3.3V
empty voltage.
Empty
Voltage
nNVCfg0.enVE = 1 word
0 2 bytes
nVEmpty
19Eh
www.maximintegrated.com
Maxim Integrated | 129
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 94. Making Nonvolatile Memory Available for User Data (continued)
RELATED
FEATURE
FREE BY
BYTES
REGISTERS
ADDRESS
COMMENTS
Charge
Termination
nNVCfg0.enICT
= 0
1 word
2 bytes
nIChgTerm
19Ch
12
words
24
bytes
SOC Table
OCV Table
nXTable[0:11]
180h–18Bh With custom models/
characterization, this is not
freeable.
Use m5 EZ
model by setting
nNVCfg.enOCV
= 0
12
words
24
nNVCfg.enX = 0
nCVTable[0:11]
190h–19Bh
bytes
nVAlrtTh
nTAlrtTh
nIAlrtTh
nSAlrtTh
4
Alert Startup
Configuration
nNVCfg1.enAT =
0
words
8 bytes
18Ch–18Fh
nUVPrtTh,
nTPrtTh1
nTPrtTh3, nIPrtTh1
nVPrtTh2,
nTPrtTh2
nProtMisTh
nProtCfg, nJEITAV
nOVPrtTh,
nDelayCfg
nODSCTh,
nODSCCfg
Most applications of the
MAX17320 use the
protector. However, if the
protector is entirely
OTHER
nNVCfg1.enProt 15
= 0
words
Protector
1D0h–1DFh disabled, these 32 bytes
become free NVM. The
FET drivers and protection
do not work in this
nNVCfg1.enJP = 30
0
bytes
configuration.
(below if JEITA
also off) nJEITAC,
nStepChg
Table 95. Nonvolatile Memory Configuration Options
FUNCTION WHEN
CONTROL BIT(S)
CLEARED
REGISTER
NAME
FACTORY
DEFAULT
CONTROL
BIT(S)
FUNCTION WHEN
CONTROL BIT IS SET
ADDRESS
1
nXTable0
through
nXTable11
Becomes Free ,
180h–18Bh Hold Custom Cell
Model Information
180h–18Bh
All 0x0000
nNVCfg0.enX
nNVCfg1.enAT
IC Uses Default EZ Cell
Model
18Ch
18Dh
18Eh
18Fh
nVAlrtTh
nTAlrtTh
nIAlrtTh
nSAlrtTh
0x0000
0x0000
0x0000
0x0000
1
VAlrtTh, TAlrtTh,
IAlrtTh, SAlrtTh
initialize from nVAlrtTh, nTAlrtTh,
nIAlrtTh, nSAlrtTh
Becomes Free ,
VAlrtTh, TAlrtTh, IAlrtTh,
SAlrtTh → Disabled
Threshold Values
1
nOCVTable0
through
nOCVTable11
Becomes Free ,
190h–19Bh Hold Custom Cell
Model Information
190h–19Bh
All 0x0000 nNVCfg0.enOCV
IC Uses Default EZ Cell
Model
1
Becomes Free ,
19Ch
19Dh
nIChgTerm
nFilterCfg
0x0000
0x0000
nNVCfg0.enICT
nNVCfg0.enFCfg
nIChgTerm→ IChgTerm
nFilterCfg→ FilterCfg
IChgTerm = FullCapRep/3
1
Becomes Free ,
FilterCfg = 0x0EA4
www.maximintegrated.com
Maxim Integrated | 130
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 95. Nonvolatile Memory Configuration Options (continued)
FUNCTION WHEN
CONTROL BIT(S)
CLEARED
REGISTER
NAME
FACTORY
DEFAULT
CONTROL
BIT(S)
FUNCTION WHEN
CONTROL BIT IS SET
ADDRESS
1
Becomes Free ,
19Eh
19Fh
nVEmpty
0x0000
0x0000
nNVCfg0.enVE
nVEmpty→ VEmpty
VEmpty = 0xA561
1
Becomes Free ,
nLearnCfg
nNVCfg0.enLCfg
nLearnCfg→ LearnCfg
LearnCfg = 0x2687
1A0h
1A1h
1A2h
nQRTable00
nQRTable10
nQRTable20
0x1050
0x8002
0x078C
Always QRTable Information
nQRTable00→ QRTable00
nQRTable10→ QRTable10
nQRTable20→ QRTable20
nQRTable30→ QRTable30
Always nCycles→ Cycles
1A3h
nQRTable30
0x0880
N/A
1A4h
1A5h
1A6h
1A7h
nCycles
nFullCapNom
nRComp0
0x0000
0x0D48
0x08CC
0x223E
Always nFullCapNom→ FullCapNom
Always nRComp0→ RComp0
Always nTempCo→ TempCo
nTempCo
nNVCfg1.enProt
nProtCfg.PFen
Logs/Saves Permanent Failure
1
1
1A8h
1A9h
nBattStatus
0x0000
0x0D48
Becomes Free
Becomes Free
Status
nFullCapRep
nNVCfg2.enFC
nFullCapRep→ FullCapRep
nFullCapNom→ FullCapRep
1
nNVCfg2.enVT
AvgVCell→ nVoltTemp and
AvgTA→ nVoltTemp at each
backup event
Becomes Free ,
Voltage, Temperature
Logging Disabled
(nNVCfg0.enAF
= 0)
1AAh
nVoltTemp
0x0000
nNVCfg0.enAF
1
nVoltTemp stores Age
Forecasting Information
Becomes Free ,
(nNVCfg2.enVT
= 0)
Age Forecasting Disabled
MaxMinCurr→ nMaxMinCurr at
each backup event
1
1ABh
1ACh
1ADh
nMaxMinCurr
nMaxMinVolt
nMaxMinTemp
0x0000
0x0000
0x0000
nNVCfg2.enMMC
nNVCfg2.enMMV
nNVCfg2.enMMT
Becomes Free
MaxMinVolt→ nMaxMinVolt at
each backup event
1
Becomes Free ,
MaxMinTemp→ nMaxMinTemp
at each backup event
1
Becomes Free ,
1
nFullCapFlt stores Age
Forecasting backup or stores
FaultLog information
Becomes Free ,
nFaultLog/
nFullCapFlt
nNVCfg0.enAF
nNVCfg2.enFL
1AEh
0x0000
Age Forecasting and Fault
Logging Disabled
TimerH→ nTimerH at each
backup event
1
1AFh
1B0h
nTimerH
nConfig
0x0000
0x2290
nNVCfg2.enT
N/A
Becomes Free ,
nConfig→ Config
nConfig→ Config2
1
Never Free
1B1h
1B2h
nRippleCfg
nMiscCfg
0x0204
0x0000
N/A
Always nRippleCfg→ RippleCfg
1
Becomes Free ,
nNVCfg0.enMC
nMiscCfg→ MiscCfg
MiscCfg = 0x3870
1
nDesignCap→
DesignCap
Become Free ,
1B3h
nDesignCap
0x0000
nNVCfg0.enDC
FullCapRep→ DesignCap
1
1B4h
1B5h
nSBSCfg
nPackCfg
0x0008
0x0004
nNVCfg0.enSBS
N/A
SBS Functions Enabled
Never Free
Always nPackCfg→ PackCfg
www.maximintegrated.com
Maxim Integrated | 131
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 95. Nonvolatile Memory Configuration Options (continued)
FUNCTION WHEN
CONTROL BIT(S)
CLEARED
REGISTER
NAME
FACTORY
DEFAULT
CONTROL
BIT(S)
FUNCTION WHEN
CONTROL BIT IS SET
ADDRESS
1
Becomes Free ,
1B6h
nRelaxCfg
nConvgCfg
0x083B
0x2241
nNVCfg0.enRCfg
nNVCfg1.enCTE
nRelaxCfg→ RelaxCfg
RelaxCfg = 0x2039,
1
Becomes Free ,
1B7h
Converge-to-Empty Enabled
Converge-to-Empty
Disabled
1B8h
1B9h
1BAh
1BBh
1BCh
1BDh
1BEh
1BFh
1C0h
1C1h
1C2h
1C3h
1C4h
1C5h
nNVCfg0
nNVCfg1
0x0A00
0x0182
0xBE0A
0x0909
Varies
N/A
Always Required Nonvolatile Memory Control Registers
nHibCfg Always Applies, Not Optional
nNVCfg2
nHibCfg
nROMID0
nROMID1
nROMID2
nROMID3
nPReserved0
nPReserved1
nChgCfg
Varies
N/A
N/A
Always the Unique 64-bit ID
Varies
Varies
0x0000
0x0000
0x2061
0x00E1
0x0000
0x0000
Do Not Modify without Special Guidance from Maxim
Always Required for Charge Control
nChgCtrl
1
nRGain
Becomes Free ,
nNVCfg0.enDP
nNVCfg1.enFTh
Used for Dynamic Power
Dynamic Power Disabled
nPackResistance
1
Becomes Free ,
1C6h
nFullSOCThr
0x0000
nFullSOCThr→ FullSOCThr
FullSOCThr = 0x5005
1
Becomes Free ,
nTTFCfg Configures Time-to-Full
Time-to-Full Default
Calculation
1C7h
1C8h
nTTFCfg
nCGain
0x0000
0x4000
nNVCfg1.enTTF
Configuration
N/A
Trim for Calibrating Current-Sense Gain
1
Becomes Free ,
nNVCfg1.enMtl
Metal Current Sense TempCo
Metal Current Sense
Configurable nTCurve→
TempCo Enabled,
(nNVCfg2.enMet
= 1)
CGTempCo
nCGTempCo/
nTCurve
CGTempCo = 0x20C8
1C9h
0x0000
1
nNVCfg2.enMet
= 0
Becomes Free ,
Thermistor Curvature Controlled
Thermistor Curvature
by nTCurve
(default)
Disabled
1CAh
1CBh
1CCh
1CDh
1CEh
nThermCfg
Reserved
0x71BE
0x0000
0x0000
0x0000
0x0000
N/A
N/A
Configuration for Translating Thermistor to ºC
1
Never Free
nManfctrName0
nManfctrName1
nManfctrName2
nManfctrName[2:0]→
1
nNVCfg0.enSBS
N/A
Becomes Free
sManfctrName
Sense Resistor Value—Helps Host Translate Currents and
Capacities
1CFh
nRSense
0x01F4
1D0h
1D1h
1D2h
nUVPrtTh
nTPrtTh1
nTPrtTh3
0x508C
0x3700
0x5528
1
Becomes Free
nNVCfg1.enProt Configures Protection Thresholds
Protector Disabled
www.maximintegrated.com
Maxim Integrated | 132
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 95. Nonvolatile Memory Configuration Options (continued)
FUNCTION WHEN
CONTROL BIT(S)
CLEARED
REGISTER
NAME
FACTORY
DEFAULT
CONTROL
BIT(S)
FUNCTION WHEN
CONTROL BIT IS SET
ADDRESS
1D3h
1D4h
1D5h
1D6h
1D7h
1D8h
1D9h
1DAh
1DBh
1DCh
1DDh
1DEh
nIPrtTh1
nBalTh
0x4BB5
0x0000
0x2D0A
0x7A58
0x0900
0x644B
0x0059
0xB754
0xC884
0xAB3D
0x0EAF
0x4355
nTPrtTh2
nProtMiscTh
nProtCfg
nJEITAC
nJEITAV
nOVPrtTh
nStepChg
nDelayCfg
nODSCTh
nODSCCfg
nNVCfg1.
{enProtChkSm
and enProt}
Holds CheckSum Value of
0x1A0–0x1AE for Validating NVM
at Startup
1
1DFh
1E0h
nProtCfg2
nDPLimit
0xA065
0x0000
Never Free
1
Becomes Free
Dynamic Power Disabled
nNVCfg0.enDP
Configures Dynamic Power
1
Becomes Free
1E1h
1E2h
1E3h
nScOcvLim
nAgeFcCfg
0x0000
0x0000
0xA5B9
nNVCfg1.enSC
nNVCfg0.enAF
nNVCfg0.enSBS
Used for LiFePO Gauging
4
LiFePO Disabled
4
1
Configures Age Forecast
Becomes Free
nDesignVoltage→
sDesignVolt
1
nDesignVoltage
Becomes Free
1
1
1E4h
1E5h
1E6h
1E7h
1E8h
1E9h
1EAh
1EBh
1ECh
1EDh
1EEh
1EFh
Reserved
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
N/A
N/A
Never Free
Never Free
nManfctrDate→ sManfctrDate
Reserved
1
nManfctrDate
nFirstUsed
Becomes Free
1
nFirstUsed→ sFirstUsed
Becomes Free
nSerialNumber0
nSerialNumber1
nSerialNumber2
nDeviceName0
nDeviceName1
nDeviceName2
nDeviceName3
nDeviceName4
nSerialNumber[2:0]→
sSerialNumber
1
Becomes Free
nNVCfg0.enSBS
nDeviceName[4:0]→
sDeviceName
1
Becomes Free
Note 1: "Free" indicates the address is unused and available as general user nonvolatile memory.
www.maximintegrated.com
Maxim Integrated | 133
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
100 Record Life Logging
Addresses 1A0h–1AFh support 100 burn entries of learned battery characteristics and other life logging. The save
interval is managed automatically using a Fibonacci-like algorithm which provides the following benefits:
1. Lifespan autopsy/debug data to support analysis of any aged or returned battery
1. Battery Characteristic Learning/Adaptation. FullCap (nFullCapRep, nFullCapNom), empty-compensation
(nQRTable00-30), resistance (nRComp0 and nTempCo)
2. Permanent Failure Information (nBattStatus)
3. Battery Charge/Discharge Fractional Cycle Counter (nCycles)
4. 23.9 year Timer (nTimerH)
5. Log-Interval Max/Min Voltage/Current/Temperature (nMaxMinCurr, nMaxMinVolt, nMaxMinTemp)
6. Voltage/Temperature at logging moment (nVoltTemp)
7. Faults from any moment during the logging period.
2. Intelligently managed save-intervals
1. Frequent When New. When the battery is new, the updates occur more frequently, since early information
obtained, such as full-capacity, is more critical for overall performance.
2. Slower With Age. As the battery matures the update interval slows down, since change observations progress
slower.
3. Faster Updates Following Power-Loss. This limits the loss of information associated with power-loss. This is
limited to seven reset accelerations. The reset counter is also recorded (see the nCycles register). Most battery
applications can proceed for longer than one year without interruption in power.
4. Limitation on Slowest Interval. Beyond a certain cycle life, the update interval remains constant.
Configure this behavior according to the expected battery lifespan using the FibMax and FibScl parameters in nNVCfg2
as shown in Table 96:
Table 96. Fibonacci Configuration Settings
FIBONACCI SCALAR—NNVCFG2.FIBSCL
Setting
00
0.25
01
0.5
10
1
11
1st and 2nd Interval
2
FibMax = 0
193
386
772
1544
2484
3972
6364
10186
16310
26096
41760
FibMax = 1
FibMax = 2
FibMax = 3
FibMax = 4
FibMax = 5
FibMax = 6
FibMax = 7
310.5
496.5
795.5
1273.25
2038.75
3262
621
1242
1986
3182
5093
8155
13048
20880
993
Battery
Cycles
Record
Limit
1591
2546.5
4077.5
6524
10440
5220
The bold settings in Table 96 and Table 97 are the generally recommended choices, depending on preference for update
interval, slowest update rates, and lifespan.
www.maximintegrated.com
Maxim Integrated | 134
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 97 shows the slowest update intervals associated with each configuration.
Table 97. Longest Update Interval (in battery cycles)
FIBONACCI SCALAR—NNVCFG2.FIBSCL
Setting
00
0.25
2
01
0.5
10
1
11
2
1st and 2nd Interval
FibMax = 0
FibMax = 1
FibMax = 2
FibMax = 3
FibMax = 4
FibMax = 5
FibMax = 6
FibMax = 7
4
8
16
3.25
5.25
8.5
6.5
13
21
34
55
89
144
233
26
10.5
17
42
Slowest
Update
Interval
68
13.75
22.25
36
27.5
44.5
72
110
178
288
466
58.25
116.5
Table 98 illustrates the saving schedule with the most preferred configurations.
Table 98. Saving Schedule Example With the Most Preferred Configurations
TOTAL
EX. CYCLE
LIFE
SLOWEST
UPDATE
FIBMAX FIBSCL
1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH
1
2
3
4
5
6
7
8
9
310.5
386
1
0
2
1
0
3
2
1
4
0
1
0
1
2
0
1
2
0
3.25
4
0.25 0.25 0.5
0.5 0.5
0.25 0.25 0.5
0.75 1.25
1.5 2.5
0.75 1.25
2
4
2
4
8
2
4
8
2
3.25 3.25 3.25
.
.
.
1
4
4
.
.
496.5
621
5.25
6.5
8
3.25 5.25 5.25 5.25
.
0.5
1
0.5
1
1
2
1.5
3
2.5
5
6.5
8
6.5
8
6.5
.
.
.
772
.
.
795.5
993
8.5
10.5
13
0.25 0.25 0.5
0.75 1.25
3.25 5.25 8.5
8.5
.
0.5
1
0.5
1
1
2
1.5
3
2.5
5
6.5
13
10.5 10.5 10.5
13 13
.,
.
1242
1273.25
.
13.75
0.25 0.25 0.5
0.75 1.25
3.25 5.25 8.5
13.75 13.75
As an example for all subsequent startups for the configuration of Example 9 from Table 98, see the following:
1st startup [0.25, 0.25, 0.5, 0.75, 1.25, 2, 3.25, 5.25, 8.5, 13.75, ...]
2nd startup [0.25, 0.5, 0.75, 1.25, 2, 3.25, 5.25, 8.5, 13.75, ...]
3rd startup [0.5, 0.75, 1.25, 2, 3.25, 5.25, 8.5, 13.75, ...]
4th startup [0.75, 1.25, 2, 3.25, 5.25, 8.5, 13.75, ...]
5th startup [1.25, 2, 3.25, 5.25, 8.5, 13.75, ...]
6th startup [2, 3.25, 5.25, 8.5, 13.75, ...]
7th startup [3.25, 5.25, 8.5, 13.75, ...]
8th startup [5.25, 8.5, 13.75, ...]
Memory Locks and Write Protection
ModelGauge m5 RAM Registers and all nonvolatile memory locations can be write protected or permanently locked to
prevent accidental overwriting or data loss in the application. Write protecting or locking a memory block only prevents
future writes to the locations. Reading locked locations is still allowed. The IC has write protection enabled by default and
must be disabled (as described in CommStat Register) before any registers can be written. Note that locking a memory
www.maximintegrated.com
Maxim Integrated | 135
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
location is permanent so carefully choose all desired locks before sending the NV LOCK command.
The SHA secret is stored in separate secure non-readable memory. There is a different command for locking the SHA
secret and its state is not displayed in the Lock register. See the SHA-256 Authentication section for details. Once a lock
bit is set, it can never be cleared. Table 87 shows which lock bits correspond to which memory blocks of the IC.
CommStat Register (061h)
Register Type: Special
Nonvolatile Backup: None
The CommStat register tracks the progress and error state of any command sent to the Command register. It also
provides the write protection control and status of each page of registers. Table 99 shows the register format.
Table 99. CommStat Register (061h) Format
D15 D14 D13 D12 D11 D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
DISOff CHGOff WP5 WP4 WP3 WP2 WP1 NVError NVBusy WPGlobal
X: Don’t Care. This bit is undefined and can be logic 0 or 1.
Write Protection: To prevent the host from accidentally writing any registers of the IC, write protection is enabled by
default. Any time the host wants to write a register, the global write protection must be disabled as well as the write
protection for the specific register page. To prevent accidental unlocking of the write protection, the CommStat register
must be written with the desired value two times in a row without accessing any other registers to set or clear any of the
write protection bits. All bits can be set or cleared in the same write sequence. For example, writing 0x0000 to CommStat
twice in a row clears the WPGlobal and all WP1-WP5 at the same time.
WPGlobal: Write Protection Global Enable. Set to 1 to write protect all register pages. Clear to 0 to allow individual write
protect bits (WP1–WP5) to be disabled.
WP1–WP5: Write Protection Enable Bits. Set any bit to 1 to write protect the pages specified below. Clear any bit to 0 to
allow pages to be writable. To update any of these bits, the WPGlobal bit must be 0.
WP1: Write protects register pages 1Ah, 1Bh, 1Eh
WP2: Write protects register pages 01h, 02h, 03h, 04h, 0Bh, 0Dh
WP3: Write protects register pages 18h, 19h
WP4: Write protects register pages 1Ch
WP5: Write protects register pages 1Dh
DISOff: Set this bit to 1 to forcefully turn off DIS FET ignoring all other conditions if nProtCfg.CmOvrdEn is enabled. DIS
FET remains off as long as this bit stays to 1. Clear to 0 for normal operation. Write Protection must be disabled before
writing to the DISOff bit.
CHGOff: Set this bit to 1 to forcefully turn off CHG FET ignoring all other conditions if nProtCfg.CmOvrdEn is enabled.
CHG FET remains off as long as this bit stays set to 1. Clear to 0 for normal operation. Write Protection must be disabled
before writing to the CHGOff bit.
NVBusy: This read only bit tracks if nonvolatile memory is busy or idle. NVBusy defaults to 0 after reset indicating
nonvolatile memory is idle. This bit sets after a nonvolatile related command is sent to the command register, and clears
automatically after the operation completes.
NVError: This bit indicates the results of the previous SHA-256 or nonvolatile memory related command sent to the
command register. This bit sets if there was an error executing the command or if the Full Reset command is executed.
Once set, the bit must be cleared by system software in order to detect the next error. Write Protection must be disabled
before the NVError bit can be cleared by the host.
www.maximintegrated.com
Maxim Integrated | 136
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
NV LOCK [6AXXh]
This command permanently locks a block or blocks of memory. To set a lock, send 6AXXh to the Command register
where the lower 5 bits of the command determine which locks are set. Table 100 shows a detailed format of the NV
LOCK command. Set each individual LOCK bit to 1 to lock the corresponding register block. Set the LOCK bit to 0 to do
nothing at this time. For example, writing 6A02h to the Command register sets LOCK2. Writing 6A1Fh sets all five locks.
Writing 6A00h sets no locks.
Table 100. Format of LOCK Command
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
LOCK
5
D3
LOCK
4
D2
LOCK
3
D1
LOCK
2
D0
LOCK
1
0
1
1
0
1
0
1
0
0
0
0
LOCK1: Locks register pages 1Ah, 1Bh, 1Eh
LOCK2: Locks register pages 01h, 02h, 03h, 04h, 0Bh, 0Dh
LOCK3: Locks register pages 18h, 19h
LOCK4: Locks register pages 1Ch
LOCK5: Locks register pages 1Dh
Locking Memory Blocks
Prior to sending the lock command, the CommStat.NVError bit should be cleared, and after the command is sent, the
CommStat.NVError bit should be read to determine if the lock command executed successfully. Note that locking memory
blocks is a permanent operation. The recommended full sequence is:
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Write 0x0000 to the CommStat register (0x61) one more time to clear CommStat.NVError bit.
3. Write 0x6AXX to the Command register 0x060 to lock desired blocks.
4. Wait t
for the copy to complete.
UPDATE
5. Check the CommStat.NVError bit. If set, repeat the process.
6. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
Reading Lock State
The Lock register at address 07Fh reports the state of each lock. See Table 101 for the format of the Lock register. If a
LOCK bit is set, the corresponding memory block is locked. If the LOCK bit is cleared, the corresponding memory block
is unlocked. Note that the SHA-256 Secret lock state cannot be read through this register.
Table 101. Format of Lock Register (07Fh)
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
LOCK
5
D3
LOCK
4
D2
LOCK
3
D1
LOCK
2
D0
LOCK
1
X
X
X
X
X
X
X
X
X
X
X
X: Don't Care
1: LOCK is set
0: LOCK is clear
www.maximintegrated.com
Maxim Integrated | 137
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
SHA-256 Authentication Procedures
The IC supports authentication which is performed using a FIPS 180-4 compliant SHA-256 one-way hash algorithm on
a 512-bit message block. The message block consists of a 160-bit secret, a 160-bit challenge, and 192 bits of constant
data. Optionally, the 64-bit ROM ID replaces 64 of the 192 bits of constant data used in the hash operation. Contact
Maxim for details of the message block organization.
The host and the IC both calculate the result based on the mutually known secret. The result of the hash operation is
known as the message authentication code (MAC) or message digest. The MAC is returned by the IC for comparison
to the host’s MAC. Note that the secret is never transmitted on the bus and thus cannot be captured by observing bus
traffic. Each authentication attempt is initiated by the host system by writing a 160-bit random challenge into the SHA
memory address space 0C0h to 0C9h. The host then issues the compute MAC or compute MAC with ROM ID command.
The MAC is computed per FIPS 180-4 and stored in address space 0C0h to 0CFh overwriting the challenge value.
The IC introduces the new MAC key derivation function (MKDF), a 2-stage authentication scheme that utilizes an
intermediate secret for an added layer of security.
Note that the results of the authentication attempt are determined by host verification. Operation of the IC is not affected
by authentication success or failure.
Authentication Procedure
Figure 30 shows how a host system verifies the authenticity of a connected battery. The host first generates a random
160-bit challenge value and writes the challenge to IC memory space 0C0h to 0C9h. The host then sends the Compute
MAC with ROM ID (3500h) or Compute MAC without ROM ID (3600h) to the Command register 060h and waits t
SHA
for the computation to complete. Finally, the host reads the MAC from memory space 0C0h to 0CFh to verify the result.
This procedure requires the secret to be maintained on the host side as well as in the battery. The host must perform the
same calculations in parallel to verify the battery is authentic.
www.maximintegrated.com
Maxim Integrated | 138
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Procedure to Verify a Battery
RANDOM CHALLENGE
GENERATION
SECRET
SECRET
PARALLEL
COMPUTATION
MAC COMPUTATION
BATTERY
VERIFICATION
MACs
MACs DO
NOT MATCH
REJECT
MATCH
ACCEPT
BATTERY
BATTERY
HOST
Figure 30. Procedure to Verify a Battery
www.maximintegrated.com
Maxim Integrated | 139
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Alternate Authentication Procedure
Figure 31 shows an alternative method of battery authentication which does not require the host to know the secret. In
this method, each host device knows a challenge and MAC pair that matches the secret stored in an authentic battery,
but each host device uses a different pair. This eliminates the need for special hardware on the host side to protect the
secret from hardware intrusion. A battery could be cloned for a single host device, but creating a clone battery that works
with any host would not be possible without knowing the secret.
The authentication process for this method is less complex. The host simply writes the challenge to IC memory space
0C0h to 0C9h. The host then sends the Compute MAC without ROM ID (3600h) to the Command register 060h. Note
that Compute MAC with ROM ID Command is not valid for this authentication method. The host then waits t
computation to complete and reads the MAC from memory space 0C0h to 0CFh to verify the result.
for
SHA
Battery Authentication without a Host Side Secret
CHALLENGE 1
MAC
COMPUTATION
SECRET
MAC 1
VERIFICATION
VALID BATTERY
PASS
FAIL
HOST 1
CHALLENGE 2
MAC 2
MAC
COMPUTATION
SECRET
VERIFICATION
PASS FAIL
VALID BATTERY
HOST 2
CHALLENGE N
MAC N
MAC
COMPUTATION
SECRET
VERIFICATION
PASS FAIL
VALID BATTERY
HOST N
Figure 31. Battery Authentication without a Host Side Secret
www.maximintegrated.com
Maxim Integrated | 140
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Secret Management
The secret value must be programmed to a known value prior to performing authentication in the application. The secret
cannot be written directly. Instead, the user must generate a new internal secret by performing a SHA computation with
the old internal secret and a seed value sent as a challenge. To prevent any one entity from knowing the complete
secret value, the process can be repeated multiple times by sending additional challenge seeds and performing additional
computations.
Note that secret memory can only be changed a maximum of n
times including erase operations, and nonvolatile
SECRET
memory updates are not guaranteed. See the n
write limit in the Electrical Characteristics table. Any secret
SECRET
update operation that fails does not change the secret value stored in the IC, but consumes one of the available
limited updates. Be careful not to use up all secret memory during the generation process. Maxim strongly recommends
permanently locking the secret after it has been generated.
Single-Step Secret Generation
The single-step secret generation procedure should be used in production environments where the challenge seed value
can be kept confidential, for example, when there are no OEM manufacturing steps or situations where an outside
individual or organization would need to know the challenge seed. Use the following sequence to program the IC. Since
the secret cannot be read from the IC, a parallel computation must be performed externally in order to calculate the
stored secret. Figure 32 shows an example single step secret generation operation. Note that new units have their secret
value already cleared to all 0s.
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Clear the CommStat.NVError bit.
3. Write a challenge seed value to the SHA memory space 0C0h to 0C9h.
4. Write Compute Next Secret with ROM ID 3300h or Compute Next Secret without ROM ID 3000h to the Command
register 060h.
5. Wait t
+ t
for the computation to complete and the new secret to be stored.
SHA
UPDATE
6. If CommStat.NVError is set, return to step 1, otherwise, continue.
7. Verify the secret has been generated correctly with a test challenge at this time. If verification fails, return to step 1.
See the Determining Number of Remaining Updates section to verify that enough nonvolatile memory writes remain
in order to repeat the process.
8. Write Lock Secret 6000h to the Command register 060h. Note this operation cannot be reversed.
9. Wait t
for secret to lock permanently.
UPDATE
10. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
Single-Step Secret Generation Example
SEED
STARTING
COMPUTE
SECRET CLEARED
NEXT
TO ALL 0s
PARALLEL
COMPUTATION
FINAL SECRET
BATTERY
FINAL SECRET
Figure 32. Single-Step Secret Generation Example
www.maximintegrated.com
Maxim Integrated | 141
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Multistep Secret Generation Procedure
The multistep secret generation procedure should be used in environments where an outside individual or organization
would need to know the challenge seed such as OEM manufacturing. The multistep procedure is more complicated but
allows a secret to be stored inside the IC without providing any information to an OEM manufacturer that could jeopardize
secret integrity. Figure 33 shows an example where three OEM manufacturers are each provided with a seed value for a
Compute Next operation. The final secret value stored inside the IC are known only to the top level manager who knows
all seed values and has performed the computation separately. Use the following procedures when generating a multi-
step secret. Note that the secret can only be updated or cleared n
already cleared to all 0s.
times total. New units have their secret value
SECRET
All OEMs:
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Clear the CommStat.NVError bit.
3. Write the challenge seed value to the SHA memory space 0C0h to 0C9h.
4. Write Compute Next Secret with ROM ID 3300h or Compute Next Secret without ROM ID 3000h to the Command
register 060h.
5. Wait t
+ t
for computation to complete and new secret to be stored.
SHA
UPDATE
6. If CommStat.NVError is set, return to step 1, otherwise, continue.
7. Verify the secret has been generated correctly with a test challenge at this time. If verification fails, return to step 1.
See the Determining Number of Remaining Updates section to verify that enough nonvolatile memory writes remain
in order to repeat the process.
8. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
Last OEM:
1. Follow the procedure above for the final secret update, but skip step 8.
2. Write Lock Secret 6000h to the Command register 060h. Note this operation cannot be reversed.
3. Wait t
for secret to lock permanently.
UPDATE
4. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
Top Level:
1. Generate all seed values to provide to OEMs.
2. Perform SHA calculations separately to determine what the final secret is after all manufacturing steps.
3. Keep final secret value secure.
www.maximintegrated.com
Maxim Integrated | 142
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Multistep Secret Generation Example
SEED 1 GENERATION
STARTING SECRET
CLEARED TO ALL
COMPUTE
SEED 1
NEXT
0s
CHALLENGE 1
AND MAC 1 FOR
VERIFICATION
MIDDLE SECRET 1
COMPUTATION
MIDDLE SECRET 1
OEM 1
BATTERY
SEED 3
GENERATION
COMPUTE
NEXT
SEED 2
MIDDLE SECRET 1
CHALLENGE 2
AND MAC 2 FOR
VERIFICATION
MIDDLE SECRET 2
COMPUTATION
MIDDLE SECRET 2
OEM 2
BATTERY
SEED 3
GENERATION
COMPUTE
NEXT
SEED 3
MIDDLE SECRET 2
CHALLENGE 3
AND MAC 3 FOR
VERIFICATION
FINAL SECRET
FINAL SECRET
OEM 3
BATTERY
Figure 33. Multistep Secret Generation Example
www.maximintegrated.com
Maxim Integrated | 143
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
2-Stage MKDF Authentication Scheme
The IC introduces the new 2-stage MKDF authentication scheme that utilizes an intermediate secret for an added layer
of security. Figure 34 illustrates how to create a unique intermediate secret that can be stored in the host at the factory.
Figure 35 outlines the procedure to complete the 2-stage authentication.
The following procedure implements the MKDF authentication scheme:
1. Write Copy Intermediate Secret from NVM command 3800h to the Command register 060h.
2. Write the unique challenge seed value to the SHA memory space 0C0h to 0C9h to be used to compute the next
intermediate secret.
3. Write Compute Next Intermediate Secret with ROM ID 3900h or Compute Next Intermediate Secret without ROM ID
3A00h to the Command register 060h.
4. Wait t
for computation to complete.
SHA
5. Write the challenge seed value to the SHA memory space 0C0h to 0C9h to be used to compute MAC using the
intermediate secret.
6. Write Compute MAC From Intermediate Secret with ROM ID 3D00h or Compute MAC From Intermediate Secret
without ROM ID 3C00h to the Command register 060h.
7. Wait t
for computation to complete.
SHA
8. Read the MAC from SHA memory space 0C0h to 0CFh to verify the result.
Because the intermediate secret is stored in the same RAM location used for SHA calculation, executing some
commands overwrites the intermediate secret. The functional impact is summarized as follows:
● Compute MAC and Compute Next Secret commands overwrites the intermediate secret.
● Copy intermediate secret from NVM overwrites the intermediate secret (as expected).
● Compute MAC from intermediate secret also overwrites the intermediate secret. If an intermediate secret is used for
multiple MAC calculations, the intermediate secret needs to be reconstructed after each MAC computation.
www.maximintegrated.com
Maxim Integrated | 144
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Create a Unique Intermediate Secret
UNIQUE
CHALLENGE
SECRET
COMPUTE NEXT SECRET
UNIQUE INTERMEDIATE
SECRET
FACTORY (ONCE PER HOST)
Figure 34. Create a Unique Intermediate Secret
www.maximintegrated.com
Maxim Integrated | 145
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Procedure for 2-Stage MKDF Authentication
UNIQUE INTERMEDIATE
SECRET
COMPUTE NEXT
STEP 1
INTERMEDIATE
SECRET
UNIQUE CHALLENGE
SECRET
UNIQUE INTERMEDIATE
SECRET
RANDOM CHALLENGE
GENERATION
STEP 2
STEP 3
MAC COMPUTATION FROM
INTERMEDIATE SECRET
PARALLEL COMPUTATION
VERIFICATION
BATTERY
MACs
MATCH
ACCEPT
BATTERY
MACs DO
NOT MATCH
REJECT
BATTERY
HOST
Figure 35. Procedure for 2-Stage MKDF Authentication
www.maximintegrated.com
Maxim Integrated | 146
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Determining Number of Remaining Updates
The internal secret can only be updated or cleared n
calculated using the following procedure:
times total. The number of remaining updates can be
SECRET
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Write 0xE29D to the Command register (060h).
3. Wait t
.
RECALL
4. Read memory address 1FDh.
5. Decode address 1FDh data as shown in Table 102. Each secret update has redundant indicator flags for reliability.
Logically OR the upper and lower bytes together then count the number of 1s to determine how many updates have
already been used. The first update occurs in the manufacturing test to clear the secret memory prior to shipping to
the user.
6. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
Table 102. Number of Remaining Secret Updates
ADDRESS 0E6H
DATA
LOGICAL OR OF UPPER AND LOWER
BYTES
NUMBER OF UPDATES
USED
NUMBER OF UPDATES
REMAINING
0000000x00000001b
or
00000001b
00000011b
00000111b
00001111b
00011111b
00111111b
1
2
3
4
5
6
5
4
3
2
1
0
000000010000000xb
000000xx0000001xb
or
0000001x000000xxb
00000xxx000001xxb
or
000001xx00000xxxb
0000xxxx00001xxxb
or
00001xxx0000xxxxb
000xxxxx0001xxxxb
or
0001xxxx000xxxxxb
00xxxxxx001xxxxxb
or
001xxxxx00xxxxxxb
Authentication Commands
All SHA authentication commands are written to memory address 060h to perform the desired operation. Writing the
Challenge or reading the MAC is handled by accessing the SHA memory space on page 0Ch through direct write and
read operations. Note that write protection must be disabled before issuing any of the SHA-256 commands.
COMPUTE MAC WITHOUT ROM ID [3600h]
The challenge value must be written to the SHA memory space prior to performing a Compute MAC. This command
initiates a SHA-256 computation without including the ROM ID in the message block. Instead, the ROM ID portion of the
message block is replaced with a value of all 1s. Since the ROM ID is not used, this command allows the use of a master
secret and MAC response independent of the ROM ID. The IC computes the MAC in t
after receiving the last bit of
SHA
this command. After the MAC computation is complete, the host can read the MAC from the SHA memory space.
COMPUTE MAC WITH ROM ID [3500h]
The challenge value must be written to the SHA memory space prior to performing a Compute MAC. This command is
www.maximintegrated.com
Maxim Integrated | 147
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
structured the same as the compute MAC without ROM ID, except that the ROM ID is included in the message block.
With the unique ROM ID included in the MAC computation, the MAC is unique to each unit. After the MAC computation
is complete, the host can read the MAC from the SHA memory space.
COMPUTE NEXT SECRET WITHOUT ROM ID [3000h]
This command initiates a SHA-256 computation and uses the resulting MAC as the next or new secret. The hash
operation is performed with the current 160-bit secret and the new 160-bit challenge. Logical 1s are loaded in place of
the ROM ID. The last 160 bits of the MAC are used as the new secret value. The host must allow t
after issuing this
SHA
command for the SHA calculation to complete, then wait t
for the new secret value to be stored in nonvolatile
UPDATE
memory. During this operation, the SHA memory space is not updated. Note that the old secret value must be known
prior to executing this command in order to calculate what the new secret value is.
COMPUTE NEXT SECRET WITH ROM ID [3300h]
This command initiates a SHA-256 computation and uses the resulting MAC as the next or new secret. The hash
operation is performed with the current 160-bit secret, the 64-bit ROM ID, and the new 160-bit challenge. The last 160
bits of the output MAC are used as the new secret value. The host must allow t
after issuing this command for the
SHA
SHA calculation to complete, then wait t
for the new secret value to be stored in nonvolatile memory. During this
UPDATE
operation, the SHA memory space is not updated. Note that the old secret value must be known prior to executing this
command in order to calculate what the new secret value is.
CLEAR SECRET [5A00h]
This command sets the 160-bit secret to all 0s. The host must wait t
for the IC to write the new secret value to
UPDATE
nonvolatile memory. This command uses up one of the secret write cycles.
LOCK SECRET [6000h]
This command write protects the secret to prevent accidental or malicious overwrite of the secret value. The secret value
stored in nonvolatile memory becomes permanent. The host must wait t for the lock operation to complete.
UPDATE
The SHA-256 Lock state is not shown in the Lock register. Lock state can be verified by reading nonvolatile memory
history using the following sequence:
1. Write 0x0000 to the CommStat register (0x61) two times in a row to unlock write protection.
2. Send 0xE29B to the Command register (060h).
3. Wait for t
.
RECALL
4. Read memory address 1FCh.
5. Write 0x00F9 to the CommStat register (0x61) two times in a row to lock write protection.
If address 1FCh is 0x0000, then the secret is not locked. If address 1FCh is anything other than 0x0000, then the secret
is permanently locked.
COPY INTERMEDIATE SECRET FROM NVM [3800]
This command copies the secret from NVM and places it in RAM to allow the secret to be used by the other commands.
COMPUTE NEXT INTERMEDIATE SECRET WITH ROMID [3900]
This command is similar to COMPUTE NEXT SECRET WITH ROMID except the secret used in the computation comes
from the previously executed COPY INTERMEDIATE SECRET FROM NVM or COMPUTE NEXT INTERMEDIATE
SECRET WITH/WITHOUT ROMID and the next secret is placed in RAM so it can be used in subsequent commands.
COMPUTE NEXT INTERMEDIATE SECRET WITHOUT ROMID [3A00]
This command is similar to COMPUTE NEXT SECRET WITHOUT ROMID except the secret used in the computation
comes from the previously executed COPY INTERMEDIATE SECRET FROM NVM or COMPUTE NEXT
INTERMEDIATE SECRET WITH/WITHOUT ROMID and the next secret is placed in RAM so it can be used in
subsequent commands.
www.maximintegrated.com
Maxim Integrated | 148
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
COMPUTE MAC FROM INTERMEDIATE SECRET WITHOUT ROMID [3C00]
This command is the same as COMPUTE MAC WITHOUT ROMID except the secret used in the computation comes
from the previously executed COPY INTERMEDIATE SECRET FROM NVM or COMPUTE NEXT INTERMEDIATE
SECRET WITH/WITHOUT ROMID.
COMPUTE MAC FROM INTERMEDIATE SECRET WITH ROMID [3D00]
This command is the same as COMPUTE MAC WITH ROMID except the secret used in the computation comes from
the previously executed COPY INTERMEDIATE SECRET FROM NVM or COMPUTE NEXT INTERMEDIATE SECRET
WITH/WITHOUT ROMID.
Smart Battery Compliant Operation
The IC is compliant to the Smart Battery Specification v1.1 when nNVCfg0.enSBS = 1. Enabling SBS operation
does not interfere with normal operation of the IC. SBS formatted registers are accessed at slave address 16h, the
memory addresses 100h to 17Fh using SBS protocols. SBS functionality can be configured using the nSBSCfg and
nDesignVoltage registers.
SBS Compliant Memory Space
The IC contains an SBS v1.1 Compliant memory space on pages 10h to 17h that can be accessed using the Read Word,
Write Word, and Read Block commands at 2-wire slave address 16h. Table 103 lists the SBS compliant registers. Refer
to the SBS 1.1 Specification for details of registers at addresses 100h to 12Fh. Registers marked with Note 3 in the table
are shared between SBS and normal IC functions and are always readable regardless of IC settings. Their format is
described in the Analog Measurements section of the data sheet. All other registers on pages 13h to 17h are described
in this section. Greyed locations are reserved and should not be written to.
Table 103. SBS Register Space Memory Map
PAGE/
10_h
11_h
12_h
13_h
14_h
15_h
16_h
17_h
WORD
sManfct
Access
sManfctr
Name
0h
sFullCap
sRunTTE
sAvgTTE
sAvgTTF
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
sMinVolt
1
sRemCap
Alarm
sDevice
1h
2h
3h
4h
5h
6h
AvgPowerL
1
Name
sRemTime
Alarm
sDev
Chemistry
—
—
sMinCurr
—
1
sBattery
Mode
sManfct
3
3
3
3
[s]AvgTemp4
[s]AvgTemp3
[s]AvgTemp2
[s]AvgTemp1
2
Data
sCharging
Current
sAtRate
sAtTTF
sAtTTE
—
—
—
sCharging
Voltage
—
sBattery
Status
—
3
7h
8h
sAtRateOK
sCycles
—
—
[s]Temp4
—
—
—
—
sAvCap
—
—
3
sTemperature
sDesignCap
[s]Temp3
sMixCap
MaxPeak
Power
3
9h
Ah
Bh
sPackVoltage
sCurrent
sDesignVolt
sSpecInfo
—
—
—
[s]Temp2
—
—
—
—
—
—
—
—
—
3
SusPeak
3
[s]Temp1
3
Power
Pack
Resistance
sAvgCurrent
sManfctDate
—
3
www.maximintegrated.com
Maxim Integrated | 149
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 103. SBS Register Space Memory Map (continued)
PAGE/
10_h
11_h
12_h
13_h
14_h
15_h
16_h
17_h
WORD
sSerial
Number
Sys
Resistance
Ch
sMaxError
sRelSOC
sAbsSOC
sRemCap
—
—
—
—
sCell4
sCell3
sCell2
sCell1
sAvgCell4
sAvgCell3
sAvgCell2
sAvgCell1
—
—
—
—
—
—
—
—
2
3
MinSys
Voltage
Dh
Eh
Fh
—
—
—
3
MPP
Current
3
SPP
Current
3
1. Location is read as ASCII data using the Read Block command.
2. Location is read as Hexadecimal data using the Read Block command.
3. Location is shared between SBS and normal IC functions and is always readable regardless of IC settings.
sManfctAccess Register (100h)
Register Type: Special
Nonvolatile Backup: None
Table 104 shows the sManfctAccess register format.
Table 104. sManfctAccess Register (100h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
PFail
COFF
0
DOFF
ProtMode
0
0
0
0
0
0
0
0
PFail: Indicates whether the IC is in “Permanent Failure” mode.
COFF: During charge protection COFF = 1.
DOFF: During discharge protection DOFF = 1.
ProtMode: ProtMode indicates the protection mode of the IC, according to Table 105.
Table 105. Protection Mode Codes
PROTMODE CODE
PROTECTION MODE
1001b
1010b
0000b
0001b
0010b
0011b
0100b
0110b
0101b
0111b
1010b
1101b
1010b
1011b
Permanent Failure
Cell Imbalance
Discharging
Charging
Pre-Charge Mode
Undervoltage
Charge Suspension1
Sleep Mode
Charge Suspension2
Fully Charged
Overdischarge Current
Overdischarge Current
Overcharge Current
Overcharge Current
www.maximintegrated.com
Maxim Integrated | 150
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 105. Protection Mode Codes (continued)
PROTMODE CODE
PROTECTION MODE
1100b
1011b
Battery Failure
Overdischarge Temp
sRemCapAlarm/sRemTimeAlarm Registers (101h/102h)
Register Type: Capacity/Time
Nonvolatile Restore: None
sRemCapAlarm: sRemCapAlarm defaults to DesignCap/10 at startup.
sRemTimeAlarm: sRemTimeAlarm defaults to 10min at startup.
sBatteryMode Register (103h)
Register Type: Special
Nonvolatile Backup: None
Table 106 shows the sBatteryMode register format.
Table 106. sBatteryMode Register (103h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CapMd
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Only the CAPACITY_MODE bit is supported from the SBS spec for this register.
CapMd: CAPACITY_MODE from SBS. If CapMd = 1, the current and capacity registers report with an LSB of 10mW/
10mWh instead of 1mA/1mAh. If CapMd = 0, the capacity registers report with an LSB of 1mAh.
At-Rate Functionality
sAtRate Register (104h)
Register Type: Current
Nonvolatile Backup: None
Host software should write the sAtRate register with a negative two’s-complement 16-bit value of a theoretical load
current prior to reading any of the at-rate output registers. AtRate calculations are performed using sAtRate (0x104) if
enSBS = 1, or AtRate(0x004) if enSBS = 0.
sAtTTF Register (105h)
Register Type: Time
Nonvolatile Backup: None
The sAtTTF register can be used to estimate time to full for any theoretical current load entered into the sAtRate register.
AtRate calculations are performed using either sAtRate (0x104) if enSBS = 1, or AtRate(0x004) if enSBS = 0.
sAtTTE Register (106h)
Register Type: Time
Nonvolatile Backup: None
The sAtTTE register can be used to estimate time-to-empty for any theoretical current load entered into the sAtRate
register. The AtTTE register displays the estimated time-to-empty for the application by dividing AtAvCap by the sAtRate
register value. sAtTTE is translated from AtTTE for conversion into minutes. AtRate calculations are performed using
either sAtRate (0x104) if enSBS = 1, or AtRate(0x004) if enSBS = 0.
www.maximintegrated.com
Maxim Integrated | 151
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
sAtRateOK Register (107h)
Register Type: Special
Nonvolatile Restore: None
From SBS specifications for AtRateOK:
Description:
Returns a Boolean value that indicates whether or not the battery can deliver the previously written AtRate value of
additional energy for 10 seconds (Boolean). If the AtRate value is zero or positive, the AtRateOK function always returns
true. Result can depend on the setting of the CAPACITY_MODE bit.
Purpose:
The AtRateOK function is part of a two-function call set used by power management systems to determine if the battery
can safely supply enough energy for an additional load. It is used immediately after the SMBus host sets the AtRate
value. See the AtRate register for additional usage information.
sTemperature Register (108h)
Register Type: Temperature
Nonvolatile Restore: None
Temperature is translated from the AvgTA register.
sPackVoltage Register (109h)
Register Type: Voltage
Nonvolatile Restore: None
sPackVoltage is translated from the PCKP Register.
sChargingCurrent Register (114h)
Register Type: Current
Nonvolatile Restore: None
As for the SBS, this register returns the smart battery's desired charging rate in milliampere.
sBatteryStatus Register (116h)
Register Type: Special
Nonvolatile Backup: None
Table 107. BatteryStatus Register (116h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
OChg
TChg
X
OTmp
TDis
X
RCA
RTA
Init
Dis
Full
Empty
0
0
0
0
X: Don't Care.
OChg: Over_Charged_Alarm. Set when: Fully charged (0x47), or OverChargeTemp (0x4B), or
OverChargeCurrent(0x4A), or ChargeSuspension (0x44). Cleared for other modes.
TChg: Terminate_Charge_Alarm: Set when: FullyCharged (0x47), or OverChargeTemp (0x4B), or OverChargeCurrent
(0x4A), or ChargeSuspension (0x44), or BatteryFailure (0x4C), or Permanent Failure (0x89). Cleared for other modes.
OTmp: Over_Temp_Alarm. Set when: OverChargeTemp (0x4B) or OverDischargeTemp (0x8B). Cleared for other
modes.
TDis: Terminate_Discharge_Alarm. Set when: Min_Cel < V_TBD or OverDischargeCurrent (0x1A or 0x8D), or RSOC <
SALRT_Th1.Min, or OverDischargeTemp (0x8B). Cleared if Min_Cell > V_TBD, and RSOC > SOC_TBD, and not (0x1A
or 0x8D).
www.maximintegrated.com
Maxim Integrated | 152
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
RCA: RemCapAlarm. Set if sRemCap < RemCapAlarm. Cleared otherwise.
RTA: RemainingTimeAlarm. Set if AverageTimeToEmpty < RemTimeAlarm, cleared otherwise.
Init: Initialized. Always 1.
Dis: Discharging. Set if sCurrent ≤ 0mA and cleared if sCurrent > 0.
Full: Fully_Charged. Set if (RepSOC > 0x6380 (99.5%)). Cleared when RepSOC < 85%.
Empty: Fully_Discharged. Set if RepSOC < 1%. Cleared when RepSOC ≥ 19%.
sSpecInfo Register (11Ah)
Register Type: Special
Nonvolatile Backup: None
Table 108. SpecInfo Register (11Ah) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
0
0
1
1 (PEC)
0
0
0
1
PEC: PEC indicates whether the pack is configured to support SMBus PEC correction. PEC is always enabled on the
MAX17320 in SBS Mode.
sManfctrDate Register (11Bh)
Register Type: Special
Nonvolatile Backup: None
Table 109. sManfctrDate Register (11Bh) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Year
Month
Day
sManfctrDate indicates the manufacturer’s date, according to the value stored in MTP, nManfctrDate.
sSerialNumber Register (11Ch to 11Eh)
Register Type: Special
Nonvolatile Restore: None
SerialNumber indicates the 16-bit serial number as stored in nSerialNumber MTP. SerialNumber2 and SerialNumber3
provide extended data for the serial number as stored in nSerialNumber2 and nSerialNumber3. By using 6 bytes total, a
serial number can provide a very unique ID for 281 trillion devices. A 4-byte serial number can support 4.3 billion devices.
Some of the bits can be fixed to indicate platform or other information.
sManfctrName Register (120h)
Register Type: Special
Nonvolatile Restore: nManfctrName
2
2
A block SMBus/I C read of 0x20 on the I C slave 0x16 (SBS) reports RAM address 0x120 sequenced with 0x146 to
0x14A, for a total of 6 words of data. The first byte indicates the byte length and the following bytes are ASCII characters
representing the brand name of the pack. This data is taken from nManfctrName in NVM, except that the byte count is
set by firmware instead of saved in NVM.
sDeviceName Register (121h)
Register Type: Special
Nonvolatile Restore: nDeviceName
2
2
A block SMBus/I C read of 0x21 on the I C slave 0x16 (SBS) reports RAM address 0x121 sequenced with 0x140 to
www.maximintegrated.com
Maxim Integrated | 153
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
0x143, for a total of 5 words of data. The first byte indicates the byte length and the following bytes are ASCII characters
representing the device name. This data is taken from nDeviceName in NVM, except that the byte count is set by
firmware instead of saved in NVM.
sDevChemistry Register (122h)
Register Type: Special
Nonvolatile Restore: None
2
2
A block SMBus/I C read of 0x22 on the I C slave 0x16 (SBS) reports RAM address 0x122 sequenced with 0x156 to
0x158, for a total of 4 words of data. The first byte indicates the byte length and the following bytes are ASCII characters
representing the device chemistry. For the IC, this string is always “LION,” which is standard for all SBS packs.
sManfctData Registers (123h to 12Fh)
Register Type: Various
Nonvolatile Restore: None
The bytes of this read-block command are defined as follows:
Byte 0: Cell count. Copy from NCELLS information.
Byte 1: High-Byte of eep_MEM_VER
Byte 2: Low-byte of eep_MEM_VER
Byte 3: High-Byte of Version
Byte 4: Low-Byte of Version
Byte 5: HCONFIG
Byte 6: HCONFIG2
Byte 7: Q
Byte 8: QH
sDesignVolt Register (119h)
Register Type: Voltage
Nonvolatile Restore: None
sDesignVolt is represented per cell.
sFirstUsed Register (136h)
This register contains a mirror of the value stored in nonvolatile memory address 1D7h.
sCell1-4 Registers (13Fh-13Ch)
This register contains the same cell voltages information displayed in Cell1-4 (0D8h-0D5h) respectively with SBS
compliant formatting. 1 LSb = 1mV giving a full scale range of 0.0V to 65.535V.
sAvgCell1-4 Registers (14Fh-14Ch)
This register contains the same average cell voltage information displayed in AvgCell1-4 (0D4h-0D1h) with SBS
compliant formatting. 1 LSb = 1mV giving a full scale range of 0.0V to 65.535V.
sAvCap Register (167h)
This register contains the same information as the AvCap (01Fh) register. It is formatted for SBS compliance where 1
LSb = 1.0mAh giving a full scale range of 0.0mAh to 65535mAh.
sMixCap Register (168h)
This register contains the same information as the MixCap (00Fh) register. It is formatted for SBS compliance where 1
www.maximintegrated.com
Maxim Integrated | 154
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
LSb = 1.0mAh giving a full scale range of 0.0mAh to 65535mAh.
sManfctInfo Register (170h)
The sManfctInfo register is accessed using the SBS protocol read block command. This register function is not supported
in the IC.
nDesignVoltage Register (1E3h)
Register Type: Special
Factory Default Value: A5B9h
Nonvolatile Restore: There is no associated restore location for this register
Table 110. nDesignVoltage Register (1E3h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Vminsys
Vdesign
Vminsys: (unsigned byte) = 'Minimum system voltage' specification for the design. Generates MinSysVoltage value.
Vdesign: (unsigned byte) = 'Design voltage' specification for the design.
Each byte has an LSb = 20mV (resolution) giving a full scale range = 0V to 5.12V.
These values are used in SBS calculations only when enSBS = 1.
nSBSCfg Register (1B4h)
Register Type: Special
Nonvolatile Restore: There is no associated restore location for this register.
The nSBSCfg register manages settings for SBS mode operation of the IC. Table 111 shows the register format.
Table 111. nSBSCfg Register (1B4h) Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CapMd
X
X
X
X
X
X
X
X
X
X
X
WPen
MECfg
X
X: Don’t Care. This bit is undefined and can be logic 0 or 1.
MECfg: Configures sMaxError register output when operating in SBS mode.
00: Always report 0% error
01: Always report 1% error
10: Report actual experienced error
11: Always report 3% error
CapMd: Selects the sBatteryMode.CapMd bit default setting when operating in SBS mode. CapMd resets to 0 every time
a pack removal occurs as detected by floating communication lines.
WPen: Write Protection Enable. Set WPen to 0 for SBS mode.
Nonvolatile SBS Register Backup
When SBS mode operation is enabled by setting nNVCfg0.enSBS = 1, data from several nonvolatile memory locations
is translated into SBS memory space. Table 112 lists these translations. Note that when performing an SBS Read Block
command, the IC automatically generates the size data byte by counting the number of sequential non-zero data bytes
stored in the corresponding nonvolatile memory locations. The nonvolatile memory only needs to store the actual data
to be read by an SBS Read Block command. If SBS mode of operation is disabled, these locations become available for
general-purpose nonvolatile data storage.
www.maximintegrated.com
Maxim Integrated | 155
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 112. SBS to Nonvolatile Memory Mapping
NONVOLATILE MEMORY
ADDRESS
NONVOLATILE MEMORY REGISTER
NAME
SBS MEMORY
ADDRESS
S REGISTER
NAME
1D6h
1D7h
nManfctrDate
nFirstUsed
1Bh
sManfctrDate
sFirstUsed
36h
20h
1CCh–1CEh
1D8h–1DAh
1DBh–1DFh
nManfctrName[2:0]
nSerialNumber[2:0]
nDeviceName[4:0]
sManfctrName
sSerialNumber
sDeviceName
(Read Block Command)
1Ch
(Read Block Command)
21h
(Read Block Command)
nCGain and Sense Resistor Relationship
To meet SBS compliance, current and capacity registers in the SBS memory space must have an LSb bit weight of
1.0mA and 1.0mAh. The current gain must be adjusted based on the application sense resistor value to set the proper bit
weight. Table 113 shows the proper nCGain value to use for the most common sense resistor values. This is the default
register value only. It does not include any offset trim or custom gain adjustment. Note that changing the nCGain register
affects the gain reported by the standard ModelGauge m5 current and capacity registers.
Table 113. nCGain Register Settings to Meet SBS Compliance
SENSE RESISTOR VALUE (Ω)
NCGAIN REGISTER VALUE
CORRESPONDING CGAIN REGISTER VALUE
0.0025
0.005
0.010
4000h
2000h
1000h
0400h
0200h
0100h
Device Reset
There are two different levels of reset for the IC. A full reset restores the IC to its power-up state the same as if power
had been cycled. A fuel-gauge reset resets only the fuel gauge operation without resetting IC hardware. This is useful for
testing different configurations without writing nonvolatile memory. Use the following sequences to reset the IC.
FULL RESET
1. Write 0x0000 to CommStat register (0x61) two times in a row to unlock write protection.
2. Write 0x000F to the Command register 0x060 to send the full reset command to the IC.
3. Wait 10ms for the IC to reset. Write protection resets after the full reset command.
4. Write 0x0000 to CommStat register (0x61) two times in a row to unlock write protection.
5. Write 0x8000 to Config2 register 0x0AB to reset IC fuel gauge operation. This command does not disturb the state of
the protection FETs.
6. Wait for POR_CMD bit (bit 15) of the Config2 register to be cleared to indicate that the POR sequence is complete.
7. Write 0x00F9 to CommStat register (0x61) two times in a row to lock write protection.
FUEL-GAUGE RESET
1. Write 0x0000 to CommStat register (0x61) two times in a row to unlock write protection.
2. Write 0x8000 to Config2 register 0x0AB to reset IC fuel gauge operation. This command does not disturb the state of
the protection FETs.
3. Wait for POR_CMD bit (bit 15) of the Config2 register to be cleared to indicate that the POR sequence is complete.
4. Write 0x00F9 to CommStat register (0x61) two times in a row to lock write protection.
www.maximintegrated.com
Maxim Integrated | 156
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Reset Commands
There are two commands that can be used to reset either the entire IC or just the operation of the fuel gauge. Note that
the reset fuel gauge command is written to Config2 instead of the Command register.
HARDWARE RESET [000Fh to address 060h]
Send the hardware reset command to the Command register to recall all nonvolatile memory into shadow RAM and reset
all hardware-based operations of the IC. This command should always be followed by the reset fuel gauge command to
fully reset operation of the IC.
FUEL GAUGE RESET [8000h to address 0ABh]
The fuel gauge reset command resets operation of the IC without restoring nonvolatile memory values into shadow RAM.
This command allows different configurations to be tested without using one of the limited number of nonvolatile memory
writes. This command does not disturb the state of the protection FETs.
Communication
This section covers communication protocols and summarizes all special commands used by the IC. The IC
2
communicates over a 2-wire interface using either I C or SBS protocols depending on the memory address selected by
the host. The IC communicates using the Maxim 1-Wire interface.
2-Wire Bus System
2
The 2-wire version of the IC uses a 2-wire bus system to communicate by both standard I C protocol or by SBS smart
battery protocol. The slave address used by the host to access the IC determines which protocol is used and which
2
memory locations are available to read or write. The following sections apply to both protocols. See the I C and SBS Bus
System descriptions for specific protocol details.
Hardware Configuration
The 2-wire bus system supports operation as a slave-only device in a single or multi-slave and single or multi-master
system. Up to 128 slave devices can share the bus using 7-bit slave addresses. The 2-wire interface consists of a serial
data line (SDA) and serial clock line (SCL). SDA and SCL provide bidirectional communication between the IC and a
master device at speeds up to 400kHz. The ICs SDA pin operates bidirectionally. When the IC receives data, SDA
operates as an input. When the IC returns data, SDA operates as an open-drain output with the host system providing
a resistive pullup. See Figure 36. The IC always operates as a slave device, receiving and transmitting data under the
control of a master device. The master initiates all transactions on the bus and generates the SCL signal as well as the
START and STOP bits, which begin and end each transaction.
www.maximintegrated.com
Maxim Integrated | 157
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
2-Wire Bus Interface Circuitry
VPULLUP
RPULLUP
BUS MASTER
DEVICE 2-WIRE PORT
SDA/DQ
Rx DATA
Tx DATA
Rx DATA
WEAK
PULLDOWN
Tx DATA
Rx = RECEIVE
Tx = TRANSMIT
SCL/OD
Tx CLOCK
Rx CLOCK
WEAK
PULLDOWN
Figure 36. 2-Wire Bus Interface Circuitry
I/O Signaling
The following individual signals are used to build byte level 2-Wire communication sequences.
Bit Transfer
One data bit is transferred during each SCL clock cycle, with the cycle defined by SCL transitioning low to high and then
high to low. The SDA logic level must remain stable during the high period of the SCL clock pulse. Any change in SDA
when SCL is high is interpreted as a START or STOP control signal.
Bus Idle
The bus is idle, or not busy, when no master device has control. Both SDA and SCL remain high when the bus is idle.
The STOP condition is the proper method to return the bus to the idle state.
START and STOP Conditions
The master initiates transactions with a START condition by forcing a high-to-low transition on SDA while SCL is high.
The master terminates a transaction with a STOP condition by a low-to-high transition on SDA while SCL is high. A
Repeated START condition can be used in place of a STOP then START sequence to terminate one transaction and
begin another without returning the bus to the idle state. In multi-master systems, a Repeated START allows the master
to retain control of the bus. The START and STOP conditions are the only bus activities in which the SDA transitions
when SCL is high.
Acknowledge Bits
Each byte of a data transfer is acknowledged with an acknowledge bit (ACK) or a negative acknowledge bit (NACK).
Both the master and the IC slave generate acknowledge bits. To generate an ACK bit, the receiving device must pull
SDA low before the rising edge of the acknowledge-related clock pulse (ninth pulse) and keep it low until SCL returns
low. To generate a NACK bit, the receiver releases SDA before the rising edge of the acknowledge-related clock pulse
and leaves SDA high until SCL returns low. Monitoring the acknowledge bits allows for detection of unsuccessful data
transfers. An unsuccessful data transfer can occur if a receiving device is busy or if a system fault has occurred.
In the event of an unsuccessful data transfer, the bus master should reattempt communication. If a transaction is
www.maximintegrated.com
Maxim Integrated | 158
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
aborted mid-byte, the master should send additional clock pulses to force the slave IC to free the bus prior to restarting
communication.
Data Order
With 2-wire communication, a byte of data consists of 8 bits ordered most significant bit (MSb) first. The least significant
bit (LSb) of each byte is followed by an ACK bit. IC registers composed of multibyte values are ordered least significant
byte (LSB) first.
Slave Address
A bus master initiates communication with a slave device by issuing a START condition followed by a Slave Address and
the read/write (R/W) bit. When the bus is idle, the IC continuously monitors for a START condition followed by its slave
address. When the IC receives a slave address that matches its Slave Address, it responds with an ACK bit during the
clock period following the R/W bit. The IC supports the slave addresses shown in Table 114.
Table 114. 2-Wire Slave Addresses
SLAVE ADDRESS
PROTOCOL
ADDRESS BYTE RANGE
INTERNAL MEMORY RANGE ACCESSED
2
6Ch
I C
00h-FFh
000h-0FFh
100h-17Fh
180h-1FFh
SMBUS
00h-7Fh
16h
2
I C
80h-FFh
Read/Write Bit
The R/W bit following the slave address determines the data direction of subsequent bytes in the transfer. R/W = 0 selects
a write transaction, with the following bytes being written by the master to the slave. R/W = 1 selects a read transaction,
with the following bytes being read from the slave by the master.
Bus Timing
The IC is compatible with any bus timing up to 400kHz. See the Electrical Characteristics table for timing details. No
special configuration is required to operate at any speed. Figure 37 shows an example of standard 2-wire bus timing.
2-Wire Bus Timing Diagram
SDA
tF
tF
tSP
tR
tBUF
tSU;DAT
tHD;STA
tLOW
tR
SCL
tHD;STA
tSU;STA
tSU;STO
tHD;DAT
S
SR
P
S
Figure 37. 2-Wire Bus Timing Diagram
www.maximintegrated.com
Maxim Integrated | 159
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
2
I C Protocols
The following 2-wire communication protocols must be used by the bus master to access IC memory locations 000h to
1FFh. Addresses 000h to 0FFh and 180h to 1FFh can be read continuously. Addresses 100h to 17Fh must be read one
2
word at a time. These protocols follow the standard I C specification for communication.
2
I C Write Data Protocol
The Write Data protocol is used to transmit data to the IC at memory addresses from 000h to 1FFh. Addresses 000h
to 0FFh and 180h to 1FFh can be written as a block. Addresses 100h to 17Fh must be written one word at a time.
The memory address is sent by the bus master as a single byte value immediately after the slave address. The MSB
of the data to be stored is written immediately after the memory address byte is acknowledged. Because the address
is automatically incremented after the least significant bit (LSb) of each word received by the IC, the MSB of the data
at the next memory address can be written immediately after the acknowledgment of the LSB of data at the previous
address. The master indicates the end of a write transaction by sending a STOP or Repeated START after receiving the
last acknowledge bit. If the bus master continues an auto-incremented write transaction beyond address 0FFh or 1FFh,
the IC ignores the data. Data is also ignored on writes to read-only addresses but not reserved addresses. Do not write
to reserved address locations. See Figure 38 for an example Write Data communication sequence.
WRITE DATA COMMUNICATION PROTOCOL
SLAVE
ADDRESS
MEMORY
ADDRESS
DATA0
LSB
DATA0
MSB
DATA1
LSB
DATA N
MSB
EXAMPLE WORD WRITE TO I2C COMMAND REGISTER ADDRESS 060h
COMMAND
LSB
COMMAND
MSB
6Ch
(SLAVE ADDRESS)
60h
(MEMORY ADDRESS)
= SLAVE TRANSMISSION
= HOST TRANSMISSION
2
Figure 38. Example I C Write Data Communication Sequence
2
I C Read Data Protocol
The Read Data protocol is used to transmit data from IC memory locations 000h to 1FFh. Addresses 000h to 0FFh and
180h to 1FFh can be read as a block. Addresses 100h to 17Fh must be read as individual words. The memory address
is sent by the bus master as a single byte value immediately after the slave address. Immediately following the memory
address, the bus master issues a REPEATED START followed by the slave address. The IC sends an ACK bit for the
address and begins transmitting data. A word of data is read as two separate bytes that the master must acknowledge.
Because the address is automatically incremented after the least significant bit (LSb) of each word received by the IC,
the MSB of the data at the next memory address can be read immediately after the acknowledgment of the LSB of data
at the previous address. The master indicates the end of a read transaction by sending a NACK followed by a STOP.
If the bus master continues an auto-incremented read transaction beyond the memory address 0FFh or 1FFh, the IC
transmits all 1s until a NACK or STOP is received. Data from reserved address locations is undefined. See Figure 39 for
an example Read Data communication sequence.
www.maximintegrated.com
Maxim Integrated | 160
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
I2C READ DATA COMMUNICATION PROTOCOL
SLAVE
ADDRESS
MEMORY
ADDRESS
SLAVE
ADDRESS
DATA0
LSB
DATA0
MSB
DATA1
LSB
DATA N
MSB
EXAMPLE READ DATA OF CURRENT AND AVGCURRENT REGISTERS ADDRESS 01Ch-01Dh
6Ch
(SLAVE WRITE
ADDRESS)
6Dh
(SLAVE READ
ADDRESS)
Current
LSB
Current
MSB
AvgCurrent
LSB
AvgCurrent
MSB
1Ch
(MEMORY ADDRESS)
EXAMPLE READ DATA OF INTTEMP REGISTER ADDRESS 135h
16h
(SLAVE WRITE
ADDRESS)
17h
(SLAVE READ
ADDRESS)
IntTemp
LSB
IntTemp
MSB
35h
(MEMORY ADDRESS)
= SLAVE TRANSMISSION
= HOST TRANSMISSION
2
Figure 39. Example I C Read Data Communication Sequence
SBS Protocols
The following 2-wire communication protocols must be used by the bus master to access IC memory locations 100h to
17Fh. These protocols follow the smart battery specification for communication.
SBS Write Word Protocol
The Write Word protocol is used to transmit data to IC memory addresses between 100h and 17Fh that do not require
the Write Block protocol. The memory address is sent by the bus master as a single byte LSB value immediately after
the slave address, the MSb of the address is omitted. The LSB of the data to be stored is written immediately after the
memory address byte is acknowledged, followed by the MSB. A PEC byte can follow the data word, but the data word is
written without checking the validity of the PEC. The master indicates the end of a write transaction by sending a STOP
or Repeated START after receiving the last acknowledge bit. Data is ignored on writes to read-only addresses but not
reserved addresses. Do not write to reserved address locations. The Write Word protocol should not be used to write
to addresses supported by the Write Block protocol, use Write Block at these locations instead. See Figure 40 for an
example Write Word communication sequence.
www.maximintegrated.com
Maxim Integrated | 161
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Example SBS Write Word Communication Sequence
SBS WRITE WORD COMMUNICATION PROTOCOL
SLAVE
ADDRESS
MEMORY
ADDRESS
DATA
LSB
DATA
MSB
PEC
(OPTIONAL)
EXAMPLE WORD WRITE TO SBS ATRATE REGISTER AT REGISTER ADDRESS 104h
DATA
LSB
DATA
MSB
16h
(SLAVE ADDRESS)
PEC
(OPTIONAL)
04h
(MEMORY ADDRESS)
= SLAVE TRANSMISSION
= HOST TRANSMISSION
Figure 40. Example SBS Write Word Communication Sequence
SBS Read Word Protocol
The Read Word protocol is used to read data from the IC at memory addresses between 100h and 17Fh. The memory
address is sent by the bus master as a single byte LSB value immediately after the slave address, the MSb of the address
is ignored. The LSB of the data is read immediately after the memory address byte is acknowledged, followed by the
MSB. A PEC byte follows the data word. The master indicates the end of a write transaction by sending a STOP or
Repeated START after not acknowledging the last received byte. Data from reserved address locations is undefined. The
Read Word protocol should not be used to read from addresses supported by the Read Block protocol, use Read Block
at these locations instead. See Figure 41 for an example Read Word communication sequence.
Example SBS Read Word Communication Sequence
SBS READ WORD COMMUNICATION PROTOCOL
SLAVE
ADDRESS
MEMORY
ADDRESS
SLAVE
ADDRESS
DATA
LSB
DATA
MSB
PEC
(OPTIONAL)
EXAMPLE READ WORD OF SBS sTEMPERATURE REGISTER ADDRESS 108h
16h
(SLAVE WRITE
ADDRESS)
17h
(SLAVE READ
ADDRESS)
sTEMPERATURE
LSB
sTEMPERATURE
LSB
PEC
(OPTIONAL)
08h
(MEMORY ADDRESS)
= SLAVE TRANSMISSION
= HOST TRANSMISSION
Figure 41. Example SBS Read Word Communication Sequence
SBS Write Block Protocol
The SBS Write Block protocol is not supported by the IC. Use the Write Data command sequence to the corresponding
nonvolatile memory locations to update Write/Read Block register locations. See Table 103.
www.maximintegrated.com
Maxim Integrated | 162
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
SBS Read Block Protocol
The Read Block protocol is similar to the Read Word protocol except the master reads multiple words of data at once.
A data size byte is transmitted by the IC immediately after the memory address byte and before the first byte of data to
be read. The Read Block protocol is only supported at the register locations shown in Table 115. PEC error checking is
provided by the Read Block protocol if nNVCfg0.enSBS = 1. Figure 42 shows an example Read Block communication
sequence.
Example SBS Read Block Communication Sequence
SBS READ BLOCK COMMUNICATION PROTOCOL
SLAVE
ADDRESS
MEMORY
ADDRESS
SLAVE
ADDRESS
PEC
SIZE
DATA0
DATA0
DATA (size-2)
DATA3
(Optional)
Example Block Read of SBS DevChemistry Register Address 122h
16h
(SLAVE WRITE
ADDRESS)
17h
(SLAVE READ
ADDRESS)
PEC
(Optional)
22h
05h
(MEMORY ADDRESS)
(Size)
= SLAVE TRANSMISSION
= HOST TRANSMISSION
Figure 42. Example SBS Read Block Communication Sequence
Valid SBS Read Block Registers
Table 115. Valid SBS Read Block Registers
ADDRESS
REGISTER
sManfctName
sDeviceName
sDevChemistry
sManfctData
sSerialNumber
sManfctInfo
SIZE BYTE MAX VALUE
FORMAT
0120h
0Ah
0Ch
05h
1Ah
08h
18h
ASCII String
ASCII String
ASCII String
Hexadecimal
Hexadecimal
Hexadecimal
0121h
0122h
0123h
011Ch
0170h
Packet Error Checking
SBS read functions support packet error checking (PEC) if nNVCfg0.enSBS is enabled. The host system is responsible
for verifying the CRC value it receives and taking action as a result. SBS write functions accept a PEC byte but complete
the write function regardless of the value of the PEC.
The CRC can be generated by the host using a circuit consisting of a shift register and XOR gates as shown in Figure 43,
8
2
1
or it can be generated in software using the polynomial X + X + X + 1. Refer to the Smart Battery Data Specification
for more information.
www.maximintegrated.com
Maxim Integrated | 163
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
PEC CRC Generation Block Diagram
INPUT
XOR
XOR
XOR
MSb
LSb
Figure 43. PEC CRC Generation Block Diagram
1-Wire Bus System
The 1-Wire version of the IC communicates to a host through a Maxim 1-Wire interface. The 1-Wire bus is a system that
has a single bus master and one or more slaves. A multi-drop bus is a 1-Wire bus with multiple slaves, while a single-drop
bus has only one slave device. In all instances, this IC is a slave device. The bus master is typically a microprocessor in
the host system. The discussion of this bus system consists of five topics: 64-bit net address, CRC generation, hardware
configuration, transaction sequence, and 1-Wire signaling.
Hardware Configuration
Because the 1-Wire bus has only a single line, it is important that each device on the bus be able to drive it at the
appropriate time. To facilitate this, each device attached to the 1-Wire bus must connect to the bus with open-drain or
tri-state output drivers. The IC uses an open-drain output driver as part of the bidirectional interface circuitry shown in
Figure 44. If a bidirectional pin is not available on the bus master, separate output and input pins can be connected
together. Communication speed is controlled by the OD/SCL pin. Connect OD/SCL to PACK- to enable communication
at standard speed. Connect OD/SCL to the REG3 pin to enable communication at overdrive speed.
The 1-Wire bus must have a pullup resistor on the host side of the bus. A value between 2kΩ and 5kΩ is recommended
for most applications. The idle state for the 1-Wire bus is logic high. If, for any reason, a bus transaction must be
suspended, the bus must be left in the idle state to properly resume the transaction later. Note that if the bus is left low
for more than t
, slave devices on the bus begin to interpret the low period as a reset pulse, effectively terminating
LOW0
the transaction.
www.maximintegrated.com
Maxim Integrated | 164
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
1-Wire Bus Interface Circuitry
VPULLUP
BUS MASTER
DEVICE 1-WIRE PORT
RPULLUP
SDA/DQ
Rx
Tx
Rx
SCL/OD
WEAK
PULLDOWN
Tx
Rx = RECEIVE
Tx = TRANSMIT
STANDARD TIMING
VPULLUP
RPULLUP
BUS MASTER
DEVICE 1-WIRE PORT
SDA/DQ
Rx
Tx
Rx
Tx
SCL/OD
REG3
WEAK
PULLDOWN
0.47µF
Rx = RECEIVE
Tx = TRANSMIT
OVERDRIVE TIMING
Figure 44. 1-Wire Bus Interface Circuitry
64-Bit Net Address (ROM ID)
The 1-Wire net address is 64 bits in length. The term net address is synonymous with the ROM ID or ROM code
terms used in other 1-Wire documentation. The value of the net address is stored in nonvolatile memory and cannot be
changed. In a 1-Wire standard net address, the first 8 bits of the net address are the 1-Wire family code. This value is the
same for all ICs of the same type. The next 48 bits are a unique serial number. The last 8 bits are a cyclic redundancy
check (CRC) of the first 56 bits. Table 116 details the Net Address data format. The 64-bit net address and the 1-Wire I/
O circuitry built into the device enable the 1-Wire version of the IC to communicate through the 1-Wire protocol detailed
in this data sheet.
Table 116. 1-Wire Net Address Format
MSb: 8-Bit CRC
48-Bit Serial Number
LSb: 8-Bit Family Code (26h)
I/O Signaling
The 1-Wire bus requires strict signaling protocols to ensure data integrity. The four protocols used by the IC are as
follows: the initialization sequence (reset pulse followed by presence pulse), write 0, write 1, and read data. The bus
master initiates all signaling except for the presence pulse.
Reset Time Slot
The initialization sequence required to begin any communication with the IC is shown in Figure 45. The bus master
transmits (Tx) a reset pulse for t
. The bus master then releases the line and goes into Receive mode (Rx). The
RSTL
1-Wire bus line is then pulled high by the pullup resistor. After detecting the rising edge on the DQ pin, the IC waits for
t
and then transmits the presence pulse for t
. A presence pulse following a reset pulse indicates that the IC is
PDL
PDH
ready to accept a net address command.
www.maximintegrated.com
Maxim Integrated | 165
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
1-Wire Initialization Sequence
tRSTL
tRSTH
VPULLUP
tPDH
tPDL
GND
LINE TYPE LEGEND:
BUS MASTER ACTIVE-LOW
SLAVE IC ACTIVE-LOW
RESISTOR PULLUP
BOTH BUS MASTER AND SLAVE IC
ACTIVE-LOW
Figure 45. 1-Wire Initialization Sequence
Write Time Slots
A write time slot is initiated when the bus master pulls the 1-Wire bus from a logic-high (inactive) level to a logic-low level.
There are two types of write time slots: Write 1 and Write 0. All write time slots must be t in duration with a 1μs
SLOT
minimum recovery time, t
, between cycles. The IC samples the 1-Wire bus line between t
and t
REC
LOW1_MAX LOW0_MIN
after the line falls. If the line is high when sampled, a write 1 occurs. If the line is low when sampled, a Write 0 occurs.
The sample window is illustrated in Figure 46. For the bus master to generate a Write 1 time slot, the bus line must be
pulled low and then released, allowing the line to be pulled high less than t
after the start of the write time slot. For
RDV
the host to generate a Write 0 time slot, the bus line must be pulled low and held low for the duration of the write time
slot.
Read Time Slots
A read-time slot is initiated when the bus master pulls the 1-Wire bus line from a logic-high level to a logic-low level.
The bus master must keep the bus line low for at least 1μs and then release it to allow the IC to present valid data. The
bus master can then sample the data t
from the start of the read-time slot. By the end of the read-time slot, the IC
RDV
releases the bus line and allows it to be pulled high by the external pullup resistor. All read-time slots must be t
in
SLOT
duration with a 1μs minimum recovery time, t
, between cycles. See Figure 46 and the timing specifications in the
REC
Electrical Characteristics table for more information.
www.maximintegrated.com
Maxim Integrated | 166
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
1-Wire Write and Read Time Slots
WRITE 0 SLOT
WRITE 1 SLOT
tSLOT
tLOW0
tSLOT
tLOW1
VPULLUP
tREC
GND
>1s
DEVICE SAMPLE WINDOW
DEVICE SAMPLE WINDOW
MIN TYP
MAX
30s
3s
MIN TYP
MAX
30s
3s
MODE
STANDARD
15s
2s
15s
15s
2s
15s
OVERDRIVE
1s
1s
READ DATA SLOT
DATA = 0
DATA = 1
tSLOT
tSLOT
tREC
VPULLUP
tRDV
tRDV
GND
>1s
MASTER SAMPLE
WINDOW
MASTER SAMPLE
WINDOW
MODE
STANDARD
15s
2s
15s
2s
OVERDRIVE
LINE TYPE LEGEND:
BUS MASTER ACTIVE-LOW
SLAVE IC ACTIVE-LOW
RESISTOR PULLUP
BOTH BUS MASTER AND SLAVE IC
ACTIVE-LOW
Figure 46. 1-Wire Write and Read Time Slots
Transaction Sequence
The protocol for accessing the IC through the 1-Wire port is as follows:
● Initialization
● Net Address Command
● Function Command(s)
● Data Transfer (not all commands have data transfer)
www.maximintegrated.com
Maxim Integrated | 167
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Net Address Commands
Once the bus master has detected the presence of one or more slaves, it can issue one of the net address commands
described in the following sections. The name of each net address command (ROM command) is followed by the 8-bit
op code for that command in square brackets.
Read Net Address [33h]
This command allows the bus master to read the ICs 1-Wire net address. This command can only be used if there is a
single slave on the bus. If more than one slave is present, a data collision occurs when all slaves try to transmit at the
same time (open-drain produces a wired-AND result).
Match Net Address [55h]
This command allows the bus master to specifically address one IC on the 1-Wire bus. Only the addressed IC responds
to any subsequent function command. All other slave devices ignore the function command and wait for a reset pulse.
This command can be used with one or more slave devices on the bus.
Skip Net Address [CCh]
This command saves time when there is only one IC on the bus by allowing the bus master to issue a function command
without specifying the address of the slave. If more than one slave device is present on the bus, a subsequent function
command can cause a data collision when all slaves transmit data at the same time.
Search Net Address [F0h]
This command allows the bus master to use a process of elimination to identify the 1-Wire net addresses of all slave
devices on the bus. The search process involves the repetition of a simple three-step routine: read a bit, read the
complement of the bit, then write the desired value of that bit. The bus master performs this simple three-step routine on
each bit location of the net address. After one complete pass through all 64 bits, the bus master knows the address of
one device. The remaining devices can then be identified on additional iterations of the process. Refer to Chapter 5 of
®
the Book of iButton Standards for a comprehensive discussion of a net address search, including an actual example
(www.maximintegrated.com/iButtonBook).
iButton is a registered trademark of Maxim Integrated Products, Inc.
1-Wire Functions
After successfully completing one of the net address commands, the bus master can access the features of the IC with
either a Read Data or Write Data function command described in the following sections. Any other IC operation such as a
Compute MAC operation is accomplished by writing to the COMMAND register. See the Nonvolatile Memory Commands
section for details.
Read Data [69h, LL, HH]
This command reads data from the IC starting at memory address HHLL. Any memory address from 0000h to 01FFh is
a valid starting address. The LSb of the data in address HHLL is available to be read immediately after the MSb of the
address has been entered. Because the address is automatically incremented after the MSb of each byte is received,
the LSb of the data at address HHLL + 1 is available to be read immediately after the MSb of the data at address
HHLL. If the bus master continues to read beyond address 01FFh, data is undefined. Addresses labeled “Reserved” in
the memory map contain undefined data values. The Read Data command can be terminated by the bus master with a
reset pulse at any bit boundary. Reads from nonvolatile memory addresses return the data in the shadow RAM. A Recall
Data command is required to transfer data from nonvolatile memory to the shadow RAM. See the Nonvolatile Memory
Commands section for details. See Figure 47 for an example Read Data communication sequence.
Write Data [6Ch, LL, HH]
This command writes data to the IC starting at memory address HHLL. Any memory address from 0000h to 01FFh is a
valid starting address. The LSb of the data to be stored at address HHLL can be written immediately after the MSb of
the address has been entered. Because the address is automatically incremented after the MSb of each byte is written,
www.maximintegrated.com
Maxim Integrated | 168
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
the LSb to be stored at address HHLL + 1 can be written immediately after the MSb to be stored at address HHLL. If
the bus master continues to write beyond address 01FFh, the data is ignored by the IC. Writes to read-only addresses
and locked memory blocks are ignored. Do not write to RESERVED address locations. Incomplete bytes are not written.
Writes to unlocked nonvolatile memory addresses modify the shadow RAM. A Copy NV Block command is required to
transfer data from the shadow RAM to nonvolatile memory. See the Nonvolatile Memory Commands section for details.
See Figure 47 for an example Write Data communication sequence.
Example 1-Wire Communication Sequences
1-WIRE READ DATA PROTOCOL
69h
CCh
MEMORY
ADDRESS LSB
MEMORY
ADDRESS MSB
DATA0 LSB
DATA0 LSB
DATA0 MSB
DATA0 MSB
DATA1 LSB
DATA1 LSB
DATA N MSB
DATA N MSB
RESET
(OR OTHER NET
ADDRESS COMMAND)
(READ DATA
COMMAND)
1-WIRE WRITE DATA PROTOCOL
6Ch
(WRITE DATA
COMMAND)
CCh
MEMORY
ADDRESS LSB
MEMORY
ADDRESS MSB
RESET
(OR OTHER NET
ADDRESS COMMAND)
EXAMPLE OF READ NET ADDRESS
NET ADDRESS
LSB
(Family Code)
NET ADDRESS
NET ADDRESS
1
NET ADDRESS
2
NET ADDRESS
3
NET ADDRESS
4
NET ADDRESS
5
NET ADDRESS
6
33h
(READ NET ADDRESS)
MSB
(CRC)
RESET
EXAMPLE READ OF TEMP AND VCELL REGISTERS ADDRESS 0008h-0009h
69h
(READ DATA
COMMAND)
00h
(ADDRESS MSB)
CCh
(SKIP NET ADDRESS)
08h
TEMP LSB
TEMP MSB
VCELL LSB
VCELL MSB
RESET
(ADDRESS LSB)
EXAMPLE WRITE OF ATRATE REGISTER ADDRESS 0004h
6Ch
(WRITE DATA
COMMAND)
00h
(ADDRESS MSB)
CCh
(SKIP NET ADDRESS)
04h
ATRATE LSB
ATRATE MSB
RESET
(ADDRESS LSB)
= SLAVE TRANSMISSION
= HOST TRANSMISSION
Figure 47. Example 1-Wire Communication Sequences
Summary of Commands
Any operation other than writing or reading a memory location is executed by writing the appropriate command to the
Command or Config2 registers. Table 117 lists all function commands understood by the IC. For both 1-Wire and 2-Wire
communication, the function command must be written to the Command (060h) or Config2 (0ABh) registers. Device
commands are described in detail in the Authentication, Nonvolatile Memory, Reset, and Power Up sections of the data
sheet.
Table 117. All Function Commands
COMMAND
TYPE
REGISTER
HEX
DESCRIPTION
Compute MAC
Without ROM ID
Computes hash operation of the message block with logical 1s in place of
the ROM ID.
SHA
060h
3600h
Compute MAC With
ROM ID
SHA
060h
3500h Computes hash operation of the message block including the ROM ID.
www.maximintegrated.com
Maxim Integrated | 169
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Table 117. All Function Commands (continued)
COMMAND
TYPE
REGISTER
HEX
DESCRIPTION
Compute Next
Secret Without ROM
ID
Computes hash operation of the message block with logical 1s in place of
the ROM ID. The result is then stored as the new Secret.
SHA
060h
3000h
Compute Next
Secret With ROM ID
Computes hash operation of the message block including the ROM ID.
The result is then stored as the new Secret.
SHA
060h
3300h
Clear Secret
Lock Secret
Copy NV Block
NV Recall
SHA
060h
060h
060h
060h
060h
5A00h Resets the SHA-256 Secret to a value of all 0s.
SHA
6000h Permanently locks the SHA-256 Secret.
Memory
Memory
Memory
E904h Copies all shadow RAM locations to nonvolatile memory at the same time.
E001h Recalls all nonvolatile memory to RAM.
History Recall
E2XXh Recalls a page of nonvolatile memory history into RAM page 1Eh.
Permanently locks an area of memory. See the Memory Locks section for
NV Lock
Memory
Reset
060h
060h
0ABh
6AXXh
details.
Recalls nonvolatile memory into RAM and resets the IC hardware. Fuel
gauge operation is not reset.
Hardware Reset
Fuel Gauge Reset
000Fh
Restarts the fuel gauge operation without affecting nonvolatile shadow
RAM settings.
Reset
8000h
16-Reading ADC FIFO Feature
The IC supports an ADC FIFO feature, which allows a user-triggered acquisition cycle of 16-samples of AvgVCell and
AvgCurrent, sampled every 2.8s, for a total acquisition time of 45s. AvgCurrent and AvgVCell filtering is configurable (see
nFilterCfg) with a default filter time-constant of 5.625s (AvgCurrent) and 45s (AvgVCell). Set FilterCfg = 0x0E83 for faster
filtering to better match the FIFO update rate (2.8s for AvgCurrent and 11.25s for AvgVCell).
Set Config2.ADCFIFOen = 1 and disable nonvolatile nConfig.ADCFIFOen = 0 to trigger a single acquisition cycle. On
completion of acquisition, this bit self-resets to 0. Enable nonvolatile nConfig.ADCFIFOen = 1 to keep the ADC FIFO in
a continuous loop without termination. Since the ADC FIFO uses the same register-space as SBS, it is incompatible with
SBS. Set nNVCfg0.enSBS = 0 to prevent collision between these incompatible features.
The FIFO is useful for measuring system shutdown consumption during production testing. Use the following sequence
to measure the system consumption during system shutdown:
1. Ensure nNVCfg0.enSBS = 0 (generally just once during initial NVM configuration).
2. Host enables the ADC FIFO (write Config2.ADCFIFOEn = 1) and sets FilterCfg = 0E83h.
3. Host shuts everything down (except pack and the IC).
4. Host remains shut down for at least 6 seconds (ideally closer to 45s for more readings).
5. Host boots up and inspects the FIFO (slave 16h registers 00h to 1Fh) to understand the system consumption during
system shutdown.
2
NOTE: I C addresses on slave 16h from 00h to 7Fh must be read one word at a time.
The FIFO can be used in other applications to acquire voltage and current data with less frequent polling or system
wakeup by setting nonvolatile nConfig.ADCFIFOen = 1.
The memory map is shown in Table 118.
2
Table 118. I C Slave Address = 0x16 (SBS Memory Area)
INDEX
PAGE = 0
CurrentBuf0
CurrentBuf1
CurrentBuf2
PAGE = 1
VoltBuf0
VoltBuf1
VoltBuf2
PAGE = 2
CurrentMax0
CurrentMin0
CurrentMax1
PAGE = 4
VoltMax0
VoltMin0
VoltMax1
0
1
2
www.maximintegrated.com
Maxim Integrated | 170
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
2
Table 118. I C Slave Address = 0x16 (SBS Memory Area) (continued)
INDEX
PAGE = 0
CurrentBuf3
CurrentBuf4
CurrentBuf5
CurrentBuf6
CurrentBuf7
CurrentBuf8
CurrentBuf9
CurrentBufA
CurrentBufB
CurrentBufC
CurrentBufD
CurrentBufE
CurrentBufF
PAGE = 1
VoltBuf3
VoltBuf4
VoltBuf5
VoltBuf6
VoltBuf7
VoltBuf8
VoltBuf9
VoltBufA
VoltBufB
VoltBufC
VoltBufD
VoltBufE
VoltBufF
PAGE = 2
CurrentMin1
CurrentMax2
CurrentMin2
CurrentMax3
CurrentMin3
CurrentMax4
CurrentMin4
—
PAGE = 4
VoltMin1
VoltMax2
VoltMin2
VoltMax3
VoltMin3
VoltMax4
VoltMin4
—
3
4
5
6
7
8
9
A
B
C
D
E
F
—
—
—
—
—
—
—
—
ADCIndex
—
Appendix A: Reading History Data Pseudo-Code Example
The following pseudo-code can be used as a reference for reading history data from the IC. The code first reads all
flag information, tests all flag information, then reads all valid history data into a two-dimensional array. Afterwards,
the HistoryLength variable indicates the depth of the history array data. Note before starting this sequence, the Write
Protection should be disabled by writing 0x0000 to the CommStat register (0x61) two times in a row. At the conclusion of
the pseudo-code, the Write Protection should be enabled by writing 0x00F9 to the CommStat register (0x61) two times
in a row.
Int WriteFlags[26];
Int ValidFlags[26];
Boolean PageGood[100];
Int HistoryData[100][16];
Int HistoryLength;
Int word, position, flag1, flag2, flag3, flag4;
//Read all flag information from the IC
WriteCommand(0xE2FB);
Wait(t
);
RECALL
WriteFlags[0] = ReadData(0x1E1);
WriteFlags[1] = ReadData(0x1E2);
WriteFlags[2] = ReadData(0x1E3);
WriteFlags[3] = ReadData(0x1E4);
WriteFlags[4] = ReadData(0x1E5);
WriteFlags[5] = ReadData(0x1E6);
WriteFlags[6] = ReadData(0x1E7);
WriteFlags[7] = ReadData(0x1E8);
WriteFlags[8] = ReadData(0x1E9);
WriteFlags[9] = ReadData(0x1EA);
www.maximintegrated.com
Maxim Integrated | 171
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
WriteFlags[10] = ReadData(0x1EB);
WriteFlags[11] = ReadData(0x1EC);
WriteFlags[12] = ReadData(0x1ED);
WriteFlags[13] = ReadData(0x1EE);
WriteFlags[14] = ReadData(0x1EF);
WriteCommand(0xE2FC);
Wait(t
);
RECALL
WriteFlags[15] = ReadData(0x0E0);
WriteFlags[16] = ReadData(0x0E1);
WriteFlags[17] = ReadData(0x0E2);
WriteFlags[18] = ReadData(0x0E3);
WriteFlags[19] = ReadData(0x0E4);
WriteFlags[20] = ReadData(0x0E5);
WriteFlags[21] = ReadData(0x0E6);
WriteFlags[22] = ReadData(0x0E7);
WriteFlags[23] = ReadData(0x0E8);
WriteFlags[24] = ReadData(0x0E9);
WriteFlags[25] = ReadData(0x0EA);
ValidFlags[0] = ReadData(0x0EB);
ValidFlags[1] = ReadData(0x0EC);
ValidFlags[2] = ReadData(0x0ED);
ValidFlags[3] = ReadData(0x0EE);
ValidFlags[4] = ReadData(0x0EF);
WriteCommand(0xE2FD);
Wait(t
);
RECALL
ValidFlags[5] = ReadData(0x1E0);
ValidFlags[6] = ReadData(0x1E1);
ValidFlags[7] = ReadData(0x1E2);
ValidFlags[8] = ReadData(0x1E3);
ValidFlags[9] = ReadData(0x1E4);
ValidFlags[10] = ReadData(0x1E5);
ValidFlags[11] = ReadData(0x1E6);
ValidFlags[12] = ReadData(0x1E7);
ValidFlags[13] = ReadData(0x1E8);
ValidFlags[14] = ReadData(0x1E9);
ValidFlags[15] = ReadData(0x1EA);
ValidFlags[16] = ReadData(0x1EB);
ValidFlags[17] = ReadData(0x1EC);
ValidFlags[18] = ReadData(0x1ED);
www.maximintegrated.com
Maxim Integrated | 172
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
ValidFlags[19] = ReadData(0x1EE);
ValidFlags[20] = ReadData(0x1EF);
WriteCommand(0xE2FE);
Wait(t
);
RECALL
ValidFlags[21] = ReadData(0x1E0);
ValidFlags[22] = ReadData(0x1E1);
ValidFlags[23] = ReadData(0x1E2);
ValidFlags[24] = ReadData(0x1E3);
ValidFlags[25] = ReadData(0x1E4);
//Determine which history pages contain valid data
For loop = 0 to 99
{
word = (int)( loop / 8 );
position = loop % 8 ; //remainder
flag1 = (WriteFlags[word] >> position) & 0x0001;
flag2 = (WriteFlags[word] >> (position+8)) & 0x0001;
flag3 = (ValidFlags[word] >> position) & 0x0001;
flag4 = (ValidFlags[word] >> (position+8)) & 0x0001;
if (flag1 || flag2) && (flag3 || flag4)
PageGood[loop] = True;
else
PageGood[loop] = False;
}
//Read all the history data from the IC
HistoryLength = 0;
For loop = 0 to 99
{
if(PageGood[loop]) == TRUE
{
SendCommand(0xE226 + loop);
Wait(t
);
RECALL
HistoryData[HistoryLength][0] = ReadData(0x1E0);
...
HistoryData[HistoryLength][15] = ReadData(0x0EF);
HistoryLength++;
}
}
www.maximintegrated.com
Maxim Integrated | 173
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Application Circuits
Typical Application Schematic
3 TERM
FUSE*
PACK+
0.1µF
100Ω
DIS
N
100Ω
PFAIL* CHG
1kΩ
10kΩ
CP
IN
ZVC
0.47µF
0.1µF
10Ω
PCKP
0.01µF
AOLDO*
REG3
0.47µF
BATTS
CELL3*
CELL2*
0.47µF
REG2
0.47µF
0.01µF
0.01µF
0.01µF
50Ω
50Ω
50Ω
ALRT*
SDA/DQ
SCL/OD
TH4*
TH3*
CELL1
TH2*
0.01µF
MAX17320
GND
TH1*
CSP
CSN
10kΩ
5mΩ
PACK-
*OPTIONAL
www.maximintegrated.com
Maxim Integrated | 174
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Application Circuits (continued)
Typical 2S-4S Battery Pack and System Implementation
BATTERY
SYSTEM
3 TERM
FUSE
PACK+
CHARGER
N
PFAIL CHG
CP
DIS
ZVC
ALWAYS-ON
PCKP
IN
LOADS
AOLDO*
RTC
REG3
REG2
BATTS
CELL3*
CELL2*
ALRT*
SDA/DQ
SYSTEM LOAD
SCL/OD
TH4*
TH3*
CELL1
TH2*
MAX17320
GND
TH1*
CSP
CSN
PACK-
*OPTIONAL
The IC measures voltage of the cells and balances the charge using internal FETs and the balancing resistors. It also
measures current using a sense resistor that is accumulated to give a coulomb count and measures temperature using
an on-chip sensor or up to 4 external thermistors, since the cells are likely to be located far away from the IC. The
protector control drives a pair of high-side N-channel FETs. The IC also opens a three-terminal fuse for harsh faults that
necessitate the battery to be permanently disabled for safety reasons. To power small loads like real-time clocks or
housekeeping microcontrollers that need to be always on, the IC provides a regulated output that stays alive even when
the protection FETs are opened. This output powers down only when the cells are severely depleted and, therefore,
prevents any further drain for safety reasons.
www.maximintegrated.com
Maxim Integrated | 175
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Application Circuits (continued)
Typical Application with a Fuse
3 TERM
FUSE
PACK+
N
PFAIL CHG
DIS
ZVC
CP
IN
PCKP
AOLDO*
REG3
REG2
BATTS
CELL3*
CELL2*
ALRT*
SDA/DQ
SCL/OD
TH4*
TH3*
CELL1
TH2*
MAX17320
GND
TH1*
CSP
CSN
PACK-
*OPTIONAL
The IC can permanently open a three-terminal fuse with the PFAIL pin when a permanent failure is detected. A
secondary protector can also be included to open the three-terminal fuse.
www.maximintegrated.com
Maxim Integrated | 176
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Typical Application Circuits (continued)
Pushbutton Schematic
BATT
SYSTEM
INTERFACE
PMIC
CHG
DIS
ALRT
BUTTON
PUSHBUTTON
MAX17320
1.8V (VIO
)
OPTIONAL
PULLUP
SYSTEM AP
The IC and the system can share a pushbutton to wake up the system and the IC. The diode on the system interface
PMIC blocks the pulldown when there is no supply. This prevents the wakeup for the IC when the system interface
PMIC loses power in ship mode. The diode on the ALRT pin prevents the alert pulldown from triggering a button action
on the PMIC. This prevents accidental shutdown in the event of an uncleared alert for > 10 seconds. The FET between
the IC and the System AP blocks the System AP pulldown from triggering the wakeup when the AP does not have
power. The FET acts as a level shifter and passes the pulldown alert signal in both directions when the 1.8V voltage is
present.
www.maximintegrated.com
Maxim Integrated | 177
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Ordering Information
PART NUMBER
MAX17320X10+
SHA-256
INTERFACE
1-Wire
PIN-PACKAGE
30 WLP
MAX17320X10+T
MAX17320X12+
1-Wire
30 WLP
Included
Included
1-Wire
30 WLP
MAX17320X12+T
MAX17320X20+
1-Wire
30 WLP
2
I C
30 WLP
2
MAX17320X20+T
MAX17320X22+
I C
30 WLP
2
Included
Included
I C
30 WLP
2
MAX17320X22+T
MAX17320G10+
MAX17320G10+T
MAX17320G12+
MAX17320G12+T
MAX17320G20+
MAX17320G20+T
MAX17320G22+
MAX17320G22+T
I C
30 WLP
1-Wire
1-Wire
1-Wire
1-Wire
24 TQFN
24 TQFN
24 TQFN
24 TQFN
24 TQFN
24 TQFN
24 TQFN
24 TQFN
Included
Included
2
I C
2
I C
2
Included
Included
I C
2
I C
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
www.maximintegrated.com
Maxim Integrated | 178
MAX17320
2S-4S ModelGauge m5 EZ Fuel Gauge with
Protector, Internal Self-Discharge Detection, and
SHA-256 Authentication
Revision History
REVISION REVISION
PAGES
DESCRIPTION
CHANGED
NUMBER
DATE
0
2/20
Initial release
—
Updated the General Description section, Benefits and Features section, Absolute
Maximum Ratings section, Functional Diagrams section, Detailed Description
section, Protector section, Permanent Failure section, Table 8, nUVPrtTh Register
(1D0h), nBattStatus Register (1A8h), ProtAlrt Register (0AFh), Table 56, nConfig
Register (1B0h), Table 103, and Ordering Information table; added Typical
Operating Characteristics, Battery Internal Self-Discharge Detection (ISD) section,
Configuring ISD section, Internal Self-Discharge Detection with Cell Balancing
section, Wake-Up/Shutdown section, and Battery Internal Self-Discharge Detection
Registers
1, 18, 26–29,
33–34, 37,
47–48, 50, 64,
73, 75–76, 79,
86–87, 90, 92,
98, 106, 146, 178
1
4/20
Updated the title, General Description, and Battery Internal Self-Discharge Detection
(ISD) section
2
3
4
5
6
7
5/20
5/20
6/20
6/20
8/20
8/20
1, 47
178
Updated the Ordering Information table
Updated the Simplified Block Diagram, Typical Application Schematic, and Ordering
Information table
1, 170, 178
178
Updated the Ordering Information table
Updated Table 51, the nChgCfg (1C2h) Prequal Configuration description,
nFullSOCThr Register (1C6h) description, Table 94, and Ordering Information table
95, 100, 105,
129, 178
Updated the Pin Description table
32
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max
limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2020 Maxim Integrated Products, Inc.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明