MAX3241ECAI-T [MAXIM]

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, 5.30 MM, MO-150, SSOP-28;
MAX3241ECAI-T
型号: MAX3241ECAI-T
厂家: MAXIM INTEGRATED PRODUCTS    MAXIM INTEGRATED PRODUCTS
描述:

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, 5.30 MM, MO-150, SSOP-28

信息通信管理 光电二极管
文件: 总26页 (文件大小:677K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
19-1298; Rev 9; 9/05  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
General Description  
Next-Generation Device Features  
For Space-Constrained Applications  
MAX3228E/MAX3229E: 15kV ESD-Protected,  
+2.5V to +5.5V, RS-232 Transceivers in UCSP  
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/  
MAX3246E +3.0V-powered EIA/TIA-232 and V.28/V.24  
communications interface devices feature low power con-  
sumption, high data-rate capabilities, and enhanced  
electrostatic-discharge (ESD) protection. The enhanced  
ESD structure protects all transmitter outputs and  
receiver inputs to ±1ꢀ5V using IEꢁ 1000-4-2 Air-ꢂap  
Discharge, ±85V using IEꢁ 1000-4-2 ꢁontact Discharge  
(±±5V for MAX3246E), and ±1ꢀ5V using the ꢃuman ꢄodꢅ  
Model. The logic and receiver I/O pins of the MAX3237E  
are protected to the above standards, while the transmit-  
ter output pins are protected to ±1ꢀ5V using the ꢃuman  
ꢄodꢅ Model.  
For Low-Voltage or Data Cable Applications  
MAX3380E/MAX3381E: +2.35V to +5.5V, 1µA,  
2Tx/2Rx, RS-232 Transceivers with 15kV  
ESD-Protected I/O and Logic Pins  
_______________Ordering Information  
PIN-  
PACKAGE  
PKG  
CODE  
A proprietarꢅ low-dropout transmitter output stage delivers  
true RS-232 performance from a +3.0V to +ꢀ.ꢀV power  
supplꢅ, using an internal dual charge pump. The charge  
pump requires onlꢅ four small 0.1µF capacitors for opera-  
tion from a +3.3V supplꢅ. Each device guarantees opera-  
tion at data rates of 2ꢀ05bps while maintaining RS-232  
output levels. The MAX3237E guarantees operation at  
2ꢀ05bps in the normal operating mode and 1Mbps in the  
Megaꢄaud™ operating mode, while maintaining RS-232-  
compliant output levels.  
The MAX3222E/MAX3232E have two receivers and two  
transmitters. The MAX3222E features a 1µA shutdown  
mode that reduces power consumption in batterꢅ-pow-  
ered portable sꢅstems. The MAX3222E receivers remain  
active in shutdown mode, allowing monitoring of external  
devices while consuming onlꢅ 1µA of supplꢅ current. The  
MAX3222E and MAX3232E are pin, pac5age, and func-  
tionallꢅ compatible with the industrꢅ-standard MAX242  
and MAX232, respectivelꢅ.  
The MAX3241E/MAX3246E are complete serial ports  
(three drivers/five receivers) designed for noteboo5 and  
subnoteboo5 computers. The MAX3237E (five drivers/  
three receivers) is ideal for peripheral applications that  
require fast data transfer. These devices feature a shut-  
down mode in which all receivers remain active, while  
consuming onlꢅ 1µA (MAX3241E/MAX3246E) or 10nA  
(MAX3237E).  
PART  
TEMP RANGE  
20 Thin QFN-  
MAX3222EꢁTP  
0°ꢁ to +70°ꢁ EP** (ꢀmm x  
ꢀmm)  
T20ꢀꢀ-ꢀ  
MAX3222EꢁUP  
MAX3222EꢁAP  
MAX3222EꢁWN  
MAX3222EꢁPN  
MAX3222Eꢁ/D  
0°ꢁ to +70°ꢁ 20 TSSOP  
0°ꢁ to +70°ꢁ 20 SSOP  
0°ꢁ to +70°ꢁ 18 Wide SO  
0°ꢁ to +70°ꢁ 18 Plastic DIP  
0°ꢁ to +70°ꢁ Dice*  
20 Thin QFN-  
EP** (ꢀmm x  
ꢀmm)  
MAX3222EETP  
-40°ꢁ to +8ꢀ°ꢁ  
T20ꢀꢀ-ꢀ  
MAX3222EEUP  
MAX3222EEAP  
-40°ꢁ to +8ꢀ°ꢁ 20 TSSOP  
-40°ꢁ to +8ꢀ°ꢁ 20 SSOP  
MAX3222EEWN -40°ꢁ to +8ꢀ°ꢁ 18 Wide SO  
MAX3222EEPN  
MAX3232EꢁAE  
MAX3232EꢁWE  
MAX3232EꢁPE  
-40°ꢁ to +8ꢀ°ꢁ 18 Plastic DIP  
0°ꢁ to +70°ꢁ 16 SSOP  
0°ꢁ to +70°ꢁ 16 Wide SO  
0°ꢁ to +70°ꢁ 16 Plastic DIP  
*Dice are tested at T = +25°C, DC parameters only.  
A
**EP = Exposed paddle.  
The MAX3222E, MAX3232E, and MAX3241E are avail-  
able in space-saving SO, SSOP, TQFN and TSSOP pac5-  
ages. The MAX3237E is offered in an SSOP pac5age.  
The MAX3246E is offered in the ultra-small 6 x 6 UꢁSP™  
pac5age.  
Ordering Information continued at end of data sheet.  
Pin Configurations appear at end of data sheet.  
Selector Guide appears at end of data sheet.  
Applications  
ꢄatterꢅ-Powered Equipment Printers  
Typical Operating Circuits appear at end of data sheet.  
ꢁell Phones  
ꢁell-Phone Data ꢁables  
Smart Phones  
xDSL Modems  
MegaBaud and UCSP are trademarks of Maxim Integrated  
Products, Inc.  
Noteboo5, Subnoteboo5,  
and Palmtop ꢁomputers  
Covered by U.S. Patent numbers 4,636,930; 4,679,134;  
4,777,577; 4,797,899; 4,809,152; 4,897,774; 4,999,761; and  
other patents pending.  
________________________________________________________________ Maxim Integrated Products  
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at  
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ABSOLUTE MAXIMUM RATINGS  
ꢁꢁ  
V
to ꢂND..............................................................-0.3V to +6V  
18-Pin PDIP (derate 11.11mW/°ꢁ above +70°ꢁ)..........88±mW  
20-Pin TQFN (derate 21.3mW/°ꢁ above +70°ꢁ) ........1702mW  
20-Pin TSSOP (derate 10.±mW/°ꢁ above +70°ꢁ) ........87±mW  
20-Pin SSOP (derate 8.00mW/°ꢁ above +70°ꢁ) ..........640mW  
28-Pin SSOP (derate ±.ꢀ2mW/°ꢁ above +70°ꢁ) ..........762mW  
28-Pin Wide SO (derate 12.ꢀ0mW/°ꢁ above +70°ꢁ).............1W  
28-Pin TSSOP (derate 12.8mW/°ꢁ above +70°ꢁ) ......1026mW  
32-Lead Thin QFN (derate 33.3mW/°ꢁ above +70°ꢁ)..2666mW  
6 x 6 UꢁSP (derate 12.6mW/°ꢁ above +70°ꢁ).............1010mW  
Operating Temperature Ranges  
V+ to ꢂND (Note 1)..................................................-0.3V to +7V  
V- to ꢂND (Note 1) ...................................................+0.3V to -7V  
V+ + |V-| (Note 1).................................................................+13V  
Input Voltages  
T_IN, EN, SHDN, MꢄAUD to ꢂND ........................-0.3V to +6V  
R_IN to ꢂND .....................................................................±2ꢀV  
Output Voltages  
T_OUT to ꢂND...............................................................±13.2V  
R_OUT, R_OUTꢄ (MAX3241E)................-0.3V to (V  
+ 0.3V)  
ꢁꢁ  
Short-ꢁircuit Duration, T_OUT to ꢂND.......................ꢁontinuous  
MAX32_ _Eꢁ_ _ ...................................................0°ꢁ to +70°ꢁ  
MAX32_ _EE_ _.................................................-40°ꢁ to +8ꢀ°ꢁ  
Storage Temperature Range.............................-6ꢀ°ꢁ to +1ꢀ0°ꢁ  
Lead Temperature (soldering, 10s) .................................+300°ꢁ  
ꢄump Reflow Temperature (Note 2)  
Infrared, 1ꢀs..................................................................+200°ꢁ  
Vapor Phase, 20s..........................................................+21ꢀ°ꢁ  
ꢁontinuous Power Dissipation (T = +70°ꢁ)  
A
16-Pin SSOP (derate 7.14mW/°ꢁ above +70°ꢁ) ..........ꢀ71mW  
16-Pin TSSOP (derate ±.4mW/°ꢁ above +70°ꢁ) .......7ꢀ4.7mW  
16-Pin TQFN (derate 20.8mW/°ꢁ above +70°ꢁ) .....1666.7mW  
16-Pin Wide SO (derate ±.ꢀ2mW/°ꢁ above +70°ꢁ) .....762mW  
18-Pin Wide SO (derate ±.ꢀ2mW/°ꢁ above +70°ꢁ) .....762mW  
Note 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.  
Note 2: This device is constructed using a unique set of pac5aging techniques that impose a limit on the thermal profile the device  
can be exposed to during board-level solder attach and rewor5. This limit permits onlꢅ the use of the solder profiles recom-  
mended in the industrꢅ-standard specification, JEDEꢁ 020A, paragraph 7.6, Table 3 for IR/VPR and convection reflow.  
Preheating is required. ꢃand or wave soldering is not allowed.  
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional  
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to  
absolute maximum rating conditions for extended periods may affect device reliability.  
ELECTRICAL CHARACTERISTICS  
(V = +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T  
to T , unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Notes 3, 4)  
MAX A  
ꢁꢁ  
A
MIN  
PARAMETER  
CONDITIONS  
= +3.3V or +ꢀV, T = +2ꢀ°ꢁ)  
MIN  
TYP  
MAX  
UNITS  
DC CHARACTERISTICS (V  
ꢁꢁ  
A
MAX3222E, MAX3232E,  
MAX3241E, MAX3246E  
0.3  
1
Supplꢅ ꢁurrent  
SHDN = V , no load  
mA  
ꢁꢁ  
MAX3237E  
0.ꢀ  
1
2.0  
10  
SHDN = ꢂND  
µA  
nA  
Shutdown Supplꢅ ꢁurrent  
SHDN = R_IN = ꢂND, T_IN = ꢂND or V  
(MAX3237E)  
10  
300  
ꢁꢁ  
LOGIC INPUTS  
Input Logic Low  
T_IN, EN, SHDN, MꢄAUD  
0.8  
V
V
V
V
V
= +3.3V  
= +ꢀ.0V  
2.0  
2.4  
ꢁꢁ  
ꢁꢁ  
Input Logic ꢃigh  
T_IN, EN, SHDN, MꢄAUD  
Transmitter Input ꢃꢅsteresis  
0.ꢀ  
±0.01  
±
MAX3222E, MAX3232E,  
MAX3241E, MAX3246E  
T_IN, EN, SHDN  
±1  
18  
Input Lea5age ꢁurrent  
µA  
T_IN, SHDN, MꢄAUD  
MAX3237E (Note ꢀ)  
RECEIVER OUTPUTS  
R_OUT (MAX3222E/MAX3237E/MAX3241E/  
MAX3246E), EN = V , receivers disabled  
Output Lea5age ꢁurrent  
±0.0ꢀ  
±10  
0.4  
µA  
V
ꢁꢁ  
I
= 1.6mA (MAX3222E/MAX3232E/MAX3241E/  
OUT  
MAX3246E), I  
Output Voltage Low  
= 1.0mA (MAX3237E)  
OUT  
2
_______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ELECTRICAL CHARACTERISTICS (continued)  
(V = +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T  
to T , unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Notes 3, 4)  
MAX A  
ꢁꢁ  
A
MIN  
PARAMETER  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
V
0.6  
-
V
0.1  
-
ꢁꢁ  
ꢁꢁ  
Output Voltage ꢃigh  
I
= -1.0mA  
V
OUT  
RECEIVER INPUTS  
Input Voltage Range  
-2ꢀ  
0.6  
0.8  
+2ꢀ  
V
V
V
V
V
V
= +3.3V  
= +ꢀ.0V  
= +3.3V  
= +ꢀ.0V  
1.1  
1.ꢀ  
1.ꢀ  
2.0  
0.ꢀ  
ꢁꢁ  
ꢁꢁ  
ꢁꢁ  
ꢁꢁ  
Input Threshold Low  
Input Threshold ꢃigh  
T
T
= +2ꢀ°ꢁ  
A
A
2.4  
2.4  
= +2ꢀ°ꢁ  
= +2ꢀ°ꢁ  
V
Input ꢃꢅsteresis  
V
Input Resistance  
T
3
7
5  
A
TRANSMITTER OUTPUTS  
Output Voltage Swing  
Output Resistance  
All transmitter outputs loaded with 35to ground  
±ꢀ  
±.4  
ꢀ05  
V
V
= 0, transmitter output = ±2V  
300  
ꢁꢁ  
Output Short-ꢁircuit ꢁurrent  
±60  
±2ꢀ  
mA  
V
= 0 or +3.0V to +ꢀ.ꢀV, V  
= ±12V, transmitters  
ꢁꢁ  
OUT  
Output Lea5age ꢁurrent  
µA  
V
disabled (MAX3222E/MAX3232E/MAX3241E/MAX3246E)  
MOUSE DRIVABILITY (MAX3241E)  
T1IN = T2IN = ꢂND, T3IN = V , T3OUT loaded with  
ꢁꢁ  
35to ꢂND, T1OUT and T2OUT loaded with 2.ꢀmA  
Transmitter Output Voltage  
±ꢀ  
each  
ESD PROTECTION  
ꢃuman ꢄodꢅ Model  
±1ꢀ  
±1ꢀ  
±8  
IEꢁ 1000-4-2 Air-ꢂap Discharge (except MAX3237E)  
IEꢁ 1000-4-2 ꢁontact Discharge (except MAX3237E)  
IEꢁ 1000-4-2 ꢁontact Discharge (MAX3246E onlꢅ)  
ꢃuman ꢄodꢅ Model  
R_IN, T_OUT  
5V  
5V  
±
±1ꢀ  
±1ꢀ  
±8  
T_IN, R_IN, R_OUT, EN, SHDN,  
MꢄAUD  
MAX3237E  
IEꢁ1000-4-2 Air-ꢂap Discharge  
IEꢁ1000-4-2 ꢁontact Discharge  
_______________________________________________________________________________________  
3
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
TIMING CHARACTERISTICS—MAX3222E/MAX3232E/MAX3241E/MAX3246E  
(V = +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T  
to T , unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Notes 3, 4)  
MAX A  
ꢁꢁ  
A
MIN  
PARAMETER  
SYMBOL  
CONDITIONS  
= T  
MIN  
2ꢀ0  
2ꢀ0  
TYP  
MAX  
UNITS  
T
A
to T  
MAX  
MIN  
R = 35,  
ꢁ = 1000pF,  
L
L
(MAX3222E/MAX3232E/  
MAX3241E)  
Maximum Data Rate  
5bps  
one transmitter  
switching  
T = +2ꢀ°ꢁ (MAX3246E)  
A
t
t
0.1ꢀ  
0.1ꢀ  
200  
200  
100  
ꢀ0  
PꢃL  
Receiver input to receiver output,  
ꢁ = 1ꢀ0pF  
L
Receiver Propagation Delaꢅ  
µs  
PLꢃ  
Receiver Output Enable Time  
Receiver Output Disable Time  
Transmitter S5ew  
Normal operation (except MAX3232E)  
Normal operation (except MAX3232E)  
(Note 6)  
ns  
ns  
ns  
ns  
|t  
|t  
- t  
|
|
PꢃL PLꢃ  
Receiver S5ew  
- t  
PꢃL PLꢃ  
V
ꢁꢁ  
= +3.3V, T = +2ꢀ°ꢁ,  
A
ꢁ = 1ꢀ0pF  
L
to 1000pF  
R = 35to 75, measured  
from +3.0V to –3.0V or –3.0V to  
L
Transition-Region Slew Rate  
6
30  
V/µs  
+3.0V, one transmitter switching  
TIMING CHARACTERISTICS—MAX3237E  
(V  
= +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T  
A
to T  
, unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Note 3)  
MAX A  
ꢁꢁ  
MIN  
PARAMETER  
CONDITIONS  
R = 35, ꢁ = 1000pF, one transmitter switching,  
MIN  
TYP  
MAX  
UNITS  
L
L
2ꢀ0  
MꢄAUD = ꢂND  
V
= +3.0V to +4.ꢀV, R = 35, ꢁ = 2ꢀ0pF,  
ꢁꢁ  
L
L
Maximum Data Rate  
1000  
1000  
5bps  
one transmitter switching, MꢄAUD = V  
ꢁꢁ  
V
= +4.ꢀV to +ꢀ.ꢀV, R = 35, ꢁ = 1000pF,  
ꢁꢁ  
L
L
one transmitter switching, MꢄAUD = V  
ꢁꢁ  
t
t
0.1ꢀ  
0.1ꢀ  
2.6  
PꢃL  
Receiver Propagation Delaꢅ  
R_IN to R_OUT, ꢁ = 1ꢀ0pF  
L
µs  
µs  
PLꢃ  
Receiver Output Enable Time  
Receiver Output Disable Time  
Normal operation  
Normal operation  
2.4  
| t  
| t  
| t  
V
- t  
|, MꢄAUD = ꢂND (Note 6)  
PꢃL PLꢃ  
Transmitter S5ew  
Receiver S5ew  
100  
ꢀ0  
ns  
ns  
- t  
|, MꢄAUD = V (Note 6)  
ꢁꢁ  
PꢃL PLꢃ  
- t  
|
PꢃL PLꢃ  
= +3.3V,  
MꢄAUD = ꢂND  
MꢄAUD = V  
6
30  
ꢁꢁ  
ꢁ = 1ꢀ0pF  
L
to 1000pF  
R = 35to 75,  
L
24  
1ꢀ0  
ꢁꢁ  
+3.0V to –3.0V or  
-3.0V to +3.0V,  
V/µs  
Transition-Region Slew Rate  
ꢁ = 1ꢀ0pF to 2ꢀ00pF,  
L
MꢄAUD = ꢂND  
4
30  
T
A
= +2ꢀ°ꢁ  
Note 3:MAX3222E/MAX3232E/MAX3241E: ꢁ1–ꢁ4 = 0.1µF tested at +3.3V ±10ꢆ% ꢁ1 = 0.047µF, ꢁ2, ꢁ3, ꢁ4 = 0.33µF tested at +ꢀ.0V  
±10ꢆ. MAX3237E: ꢁ1–ꢁ4 = 0.1µF tested at +3.3V ±ꢆ, ꢁ1–ꢁ4 = 0.22µF tested at +3.3V ±10ꢆ% ꢁ1 = 0.047µF, ꢁ2, ꢁ3, ꢁ4 =  
0.33µF tested at +ꢀ.0V ±10ꢆ. MAX3246E% ꢁ1-ꢁ4 = 0.22µF tested at +3.3V ±10ꢆ% ꢁ1 = 0.22µF, ꢁ2, ꢁ3, ꢁ4 = 0.ꢀ4µF tested at  
ꢀ.0V ±10ꢆ.  
Note 4:MAX3246E devices are production tested at +2ꢀ°ꢁ. All limits are guaranteed bꢅ design over the operating temperature range.  
Note 5:The MAX3237E logic inputs have an active positive feedbac5 resistor. The input current goes to zero when the inputs are at  
the supplꢅ rails.  
Note 6: Transmitter s5ew is measured at the transmitter zero crosspoints.  
4
_______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
__________________________________________Typical Operating Characteristics  
(V  
= +3.3V, 2ꢀ05bps data rate, 0.1µF capacitors, all transmitters loaded with 35and ꢁ , T = +2ꢀ°ꢁ, unless otherwise noted.)  
ꢁꢁ  
L
A
MAX3222E/MAX3232E  
OPERATING SUPPLY CURRENT  
vs. LOAD CAPACITANCE  
MAX3222E/MAX3232E  
TRANSMITTER OUTPUT VOLTAGE  
vs. LOAD CAPACITANCE  
MAX3222E/MAX3232E  
SLEW RATE vs. LOAD CAPACITANCE  
16  
14  
12  
10  
8
45  
40  
35  
30  
25  
20  
6
5
4
3
2
1
0
T1 TRANSMITTING AT 250kbps  
T2 TRANSMITTING AT 15.6kbps  
V
OUT+  
-SLEW  
+SLEW  
250kbps  
120kbps  
T1 TRANSMITTING AT 250kbps  
T2 TRANSMITTING AT 15.6kbps  
-1  
-2  
-3  
-4  
-5  
-6  
6
20kbps  
15  
10  
5
4
V
2
OUT-  
FOR DATA RATES UP TO 250kbps  
0
0
0
1000  
2000  
3000  
4000  
5000  
0
1000  
2000  
3000  
4000  
5000  
0
1000  
2000  
3000  
4000  
5000  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
MAX3241E  
TRANSMITTER OUTPUT VOLTAGE  
vs. LOAD CAPACITANCE  
MAX3241E  
OPERATING SUPPLY CURRENT  
vs. LOAD CAPACITANCE  
MAX3241E  
SLEW RATE vs. LOAD CAPACITANCE  
6
14  
60  
50  
40  
30  
20  
10  
0
1 TRANSMITTER AT 250kbps  
2 TRANSMITTERS AT 15.6kbps  
5
4
V
OUT+  
12  
10  
8
250kbps  
3
1 TRANSMITTER AT 250kbps  
2 TRANSMITTERS AT 15.6kbps  
2
120kbps  
1
0
6
-1  
-2  
-3  
-4  
-5  
-6  
20kbps  
4
2
V
OUT-  
0
0
1000  
2000  
3000  
4000  
5000  
0
1000  
2000  
3000  
4000  
5000  
0
1000  
2000  
3000  
4000  
5000  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
MAX3237E  
TRANSMITTER OUTPUT VOLTAGE  
vs. LOAD CAPACITANCE  
MAX3237E  
TRANSMITTER OUTPUT VOLTAGE  
vs. LOAD CAPACITANCE (MBAUD = GND)  
MAX3237E  
TRANSMITTER OUTPUT VOLTAGE  
vs. LOAD CAPACITANCE (MBAUD = V  
)
CC  
6
5
4
3
2
1
7.5  
5.0  
2.5  
0
6
5
1Mbps  
V
OUT+  
V
+
OUT  
4
FOR DATA RATES UP TO 250kbps  
1 TRANSMITTER AT 250kbps  
4 TRANSMITTERS AT 15.6kbps  
ALL TRANSMITTERS LOADED  
2Mbps  
1.5Mbps  
3
2
FOR DATA RATES UP TO 250kbps  
1 TRANSMITTER 250kbps  
4 TRANSMITTERS 15.6kbps  
ALL TRANSMITTERS LOADED  
1 TRANSMITTER AT FULL DATA RATE  
4 TRANSMITTERS AT 1/16 DATA RATE  
3k+ C LOAD, EACH OUTPUT  
1
WITH 3k+ C  
L
0
0
L
-1  
-2  
-3  
-1  
-2  
-3  
-4  
-5  
-6  
WITH 3k+ C  
L
-2.5  
-5.0  
-7.5  
1.5Mbps  
1Mbps  
2Mbps  
-4  
-5  
V
OUT-  
V
OUT-  
-6  
0
500 1000 1500 2000 2500 3000  
LOAD CAPACITANCE (pF)  
0
500 1000 1500 2000 2500 3000  
LOAD CAPACITANCE (pF)  
0
500  
1000  
1500  
2000  
LOAD CAPACITANCE (pF)  
_______________________________________________________________________________________  
5
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
Typical Operating Characteristics (continued)  
(V  
= +3.3V, 2ꢀ05bps data rate, 0.1µF capacitors, all transmitters loaded with 35and ꢁ , T = +2ꢀ°ꢁ, unless otherwise noted.)  
L A  
ꢁꢁ  
MAX3237E  
SLEW RATE vs. LOAD CAPACITANCE  
(MBAUD = GND)  
MAX3237E  
SLEW RATE vs. LOAD CAPACITANCE  
MAX3237E  
SUPPLY CURRENT vs. LOAD CAPACITANCE  
WHEN TRANSMITTING DATA (MBAUD = GND)  
(MBAUD = V  
)
CC  
12  
10  
70  
60  
50  
40  
30  
20  
50  
250kbps  
120kbps  
-SLEW, 1Mbps  
+SLEW, 1Mbps  
-SLEW, 2Mbps  
+SLEW, 2Mbps  
40  
30  
20  
10  
0
SR-  
SR+  
8
20kbps  
6
4
1 TRANSMITTER AT 20kbps, 120kbps, 250kbps  
4 TRANSMITTERS AT 15.6kbps  
ALL TRANSMITTERS LOADED  
1 TRANSMITTER AT 250kbps  
4 TRANSMITTERS AT 15.6kbps  
ALL TRANSMITTERS LOADED  
1 TRANSMITTER AT FULL DATA RATE  
2
0
4 TRANSMITTERS AT 1/16 DATA RATE  
10  
0
3k+ C LOAD EACH OUTPUT  
WITH 3k+ C  
L
L
WITH 3k+ C  
L
0
500  
1000  
1500  
2000  
0
500  
1000 1500 2000 2500 3000  
LOAD CAPACITANCE (pF)  
0
500  
1000 1500 2000 2500 3000  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
MAX3237E  
TRANSMITTER OUTPUT VOLTAGE  
vs. SUPPLY VOLTAGE (MBAUD = GND)  
MAX3237E  
MAX3237E SUPPLY CURRENT  
vs. SUPPLY VOLTAGE (MBAUD = GND)  
TRANSMITTER SKEW vs. LOAD CAPACITANCE  
(MBAUD = V  
)
CC  
50  
6
5
100  
80  
60  
40  
20  
0
V
+
OUT  
4
40  
30  
3
2
1 TRANSMITTER AT 250kbps  
4 TRANSMITTERS AT 15.6kbps  
ALL TRANSMITTERS LOADED  
WITH 3k+1000pF  
1
0
-1  
-2  
-3  
-4  
-5  
-6  
20  
1 TRANSMITTER AT 250kbps  
4 TRANSMITTERS AT 15.6kbps  
ALL TRANSMITTERS LOADED  
WITH 3kAND 1000pF  
|tPLH - t  
|
PHL  
10  
0
1 TRANSMITTER AT 500kbps  
4 TRANSMITTERS AT 1/16 DATA RATE  
ALL TRANSMITTERS LOADED  
V
OUT-  
4.5  
WITH 3k+ C  
L
2.0  
2.5  
3.0  
3.5  
4.0  
4.5  
5.0  
2.0  
2.5  
3.0  
3.5  
4.0  
5.0  
0
500  
1000  
1500  
2000  
SUPPLY VOLTAGE (V)  
SUPPLY VOLTAGE (V)  
LOAD CAPACITANCE (pF)  
MAX3246E  
OPERATING SUPPLY CURRENT  
vs. LOAD CAPACITANCE  
MAX3246E  
TRANSMITTER OUTPUT VOLTAGE  
vs. LOAD CAPACITANCE  
MAX3246E  
SLEW RATE vs. LOAD CAPACITANCE  
60  
55  
50  
45  
40  
35  
30  
25  
20  
15  
10  
5
16  
14  
7
6
5
4
3
2
1
0
1 TRANSMITTER AT 250kbps  
2 TRANSMITTERS AT 15.6kbps  
V
OUT+  
1 TRANSMITTER AT 250kbps  
2 TRANSMITTERS AT 15.6kbps  
12  
250kbps  
120kbps  
SR-  
SR+  
10  
8
-1  
-2  
-3  
-4  
-5  
-6  
20kbps  
6
4
V
OUT-  
0
0
1000  
2000  
3000  
4000  
5000  
0
1000  
2000  
3000  
4000  
5000  
0
1000  
2000  
3000  
4000  
5000  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
LOAD CAPACITANCE (pF)  
6
_______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂin Description  
PIN  
MAX3222E  
SO/ TSSOP/  
MAX3232E  
MAX3241E  
SO/DIP/  
SSOP/  
NAME  
FUNCTION  
MAX3237E  
MAX3246E  
20-PIN  
SSOP/  
QFN  
SO  
TQFN  
TQFN  
DIP SSOP  
16-PIN TSSOP  
TSSOP  
Receiver Enable. Active  
1±  
1
1
2
1
2
13*  
28  
23  
28  
22  
28  
ꢄ3  
F3  
EN  
Positive Terminal of  
Voltage-Doubler ꢁharge-  
Pump ꢁapacitor  
16  
1
2
ꢁ1+  
+ꢀ.ꢀV ꢂenerated bꢅ the  
ꢁharge Pump  
20  
2
3
4
3
4
1ꢀ  
1
2
3
3
4
27  
2ꢀ  
27  
24  
27  
23  
F1  
F4  
V+  
Negative Terminal of  
Voltage-Doubler ꢁharge-  
Pump ꢁapacitor  
ꢁ1-  
Positive Terminal of  
Inverting ꢁharge-Pump  
ꢁapacitor  
3
2
4
1
1
2±  
E1  
ꢁ2+  
Negative Terminal of  
Inverting ꢁharge-Pump  
ꢁapacitor  
4
6
7
6
7
3
4
6
6
7
3
4
2
3
30  
31  
D1  
ꢁ1  
ꢁ2-  
V-  
-ꢀ.ꢀV ꢂenerated bꢅ the  
ꢁharge Pump  
±,  
10,  
11  
6,  
7,  
8
8,  
1ꢀ  
ꢀ,  
12  
ꢀ, 6, 7,  
10, 12  
F6, E6,  
D6  
RS-232 Transmitter  
Outputs  
6, 1ꢀ  
8, 17  
7, 14  
8, 17  
T_OUT  
A4, Aꢀ,  
A6, ꢄ6,  
ꢁ6  
±,  
6,  
7, 14  
8, 13  
±, 16  
10, 1ꢀ  
12, 13  
8, 13  
±, 12  
±, 16  
8, ±, 11  
4–8  
1–ꢀ  
R_IN  
R_OUT  
T_IN  
RS-232 Receiver Inputs  
14  
11  
13,  
14,  
1ꢀ,  
ꢁ2, ꢄ1,  
A1, A2,  
A3  
10,  
13  
7,  
10  
12,  
1ꢀ  
18, 20,  
21  
TTL/ꢁMOS Receiver  
Outputs  
1ꢀ–1±  
17, 18  
17*, 1±*,  
22*, 23*,  
24*  
10,  
11,  
12  
12,  
13,  
14  
11,  
12  
13,  
14  
E3, E2,  
D2  
TTL/ꢁMOS Transmitter  
Inputs  
10, 11  
8, ±  
10, 11  
*These pins have an active positive feedback resistor internal to the MAX3237E, allowing unused inputs to be left unconnected.  
_______________________________________________________________________________________  
7
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂin Description (continued)  
PIN  
MAX3222E  
SO/ TSSOP/  
MAX3232E  
MAX3241E  
SSOP/  
SO/DIP/  
SSOP/  
16-PIN  
TSSOP  
NAME  
FUNCTION  
MAX3237E  
MAX3246E  
20-PIN  
TSSOP  
TQFN  
TQFN  
SO/  
QFN  
DIP SSOP  
TSSOP  
16  
17  
16  
17  
18  
1±  
13  
14  
1ꢀ  
18  
1±  
2
2ꢀ  
26  
24  
26  
Fꢀ  
F2  
ꢂND  
ꢂround  
+3.0V to +ꢀ.ꢀV Supplꢅ  
Voltage  
V
16  
26  
ꢁꢁ  
Shutdown ꢁontrol. Active  
low.  
18  
18  
20  
14*  
22  
21  
ꢄ2  
SHDN  
No ꢁonnection. For  
MAX3246E, these  
locations are not  
populated with solder  
bumps.  
ꢁ3, D3, ꢄ4,  
ꢁ4, D4, E4,  
ꢄꢀ, ꢁꢀ, Dꢀ,  
Eꢀ  
±, 16,  
2ꢀ,  
32  
1, 10,  
11, 20  
±, 12  
11, 14  
N.ꢁ.  
Megaꢄaud ꢁontrol Input.  
ꢁonnect to ꢂND for  
normal operation% connect  
1ꢀ*  
MꢄAUD  
to V  
for 1Mbps  
ꢁꢁ  
transmission rates.  
Noninverting  
ꢁomplementarꢅ Receiver  
Outputs. Alwaꢅs active.  
20,  
21  
16  
1±, 20  
EP  
R_OUTꢄ  
ꢂND  
Exposed Paddle. Solder  
the exposed paddle to  
the ground alone or leave  
unconnected.  
EP  
EP  
8
_______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
V
V
CC  
CC  
0.1µF  
0.1µF  
V
V
CC  
CC  
C1+  
C1+  
V+  
V-  
V+  
V-  
C1  
C2  
C1  
C2  
C3  
C4  
C3  
C4  
C1-  
C2+  
C1-  
C2+  
MAX3222E  
MAX3232E  
MAX3237E  
MAX3241E  
MAX3246E  
MAX3222E  
MAX3232E  
MAX3237E  
MAX3241E  
MAX3246E  
C2-  
C2-  
T_ OUT  
R_ IN  
T_ OUT  
R_ IN  
T_ IN  
T_ IN  
R_ OUT  
R_ OUT  
5kΩ  
5kΩ  
1000pF  
(2500pF, MAX3237E only)  
7kΩ  
150pF  
3kΩ  
GND  
GND  
MINIMUM SLEW-RATE TEST CIRCUIT  
Figure 1. Slew-Rate Test Circuits  
MAXIMUM SLEW-RATE TEST CIRCUIT  
into a high-impedance state when the device is in shut-  
down mode (SHDN = ꢂND). The MAX3222E/  
MAX3232E/MAX3237E/MAX3241E/MAX3246E permit  
the outputs to be driven up to ±12V in shutdown.  
Detailed Description  
Dual Charge-ꢂump koltage Converter  
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/  
MAX3246Es’ internal power supplꢅ consists of a regu-  
lated dual charge pump that provides output voltages  
of +ꢀ.ꢀV (doubling charge pump) and -ꢀ.ꢀV (inverting  
The MAX3222E/MAX3232E/MAX3241E/MAX3246E  
transmitter inputs do not have pullup resistors. ꢁonnect  
unused inputs to ꢂND or V . The MAX3237E’s trans-  
ꢁꢁ  
charge pump) over the +3.0V to +ꢀ.ꢀV V  
range. The  
ꢁꢁ  
mitter inputs have a 4005active positive-feedbac5  
charge pump operates in discontinuous mode% if the  
output voltages are less than ꢀ.ꢀV, the charge pump is  
enabled, and if the output voltages exceed ꢀ.ꢀV, the  
charge pump is disabled. Each charge pump requires  
a flꢅing capacitor (ꢁ1, ꢁ2) and a reservoir capacitor  
(ꢁ3, ꢁ4) to generate the V+ and V- supplies (Figure 1).  
resistor, allowing unused inputs to be left unconnected.  
MAX3237E MegaBaud Operation  
For higher-speed serial communications, the  
MAX3237E features Megaꢄaud operation. In  
Megaꢄaud operating mode (MꢄAUD = V ), the  
ꢁꢁ  
MAX3237E transmitters guarantee a 1Mbps data rate  
Rꢁ-232 Transmitters  
The transmitters are inverting level translators that con-  
vert TTL/ꢁMOS-logic levels to ±V EIA/TIA-232-compli-  
ant levels.  
with worst-case loads of 35in parallel with 2ꢀ0pF for  
+3.0V < V  
< +4.ꢀV. For +ꢀV ±10ꢆ operation, the  
ꢁꢁ  
MAX3237E transmitters guarantee a 1Mbps data rate  
into worst-case loads of 35in parallel with 1000pF.  
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/  
MAX3246E transmitters guarantee a 2ꢀ05bps data rate  
with worst-case loads of 35in parallel with 1000pF,  
providing compatibilitꢅ with Pꢁ-to-Pꢁ communication  
software (such as LapLin5™). Transmitters can be par-  
alleled to drive multiple receivers or mice.  
Rꢁ-232 Receivers  
The receivers convert RS-232 signals to ꢁMOS-logic  
output levels. The MAX3222E/MAX3237E/MAX3241E/  
MAX3246E receivers have inverting three-state outputs.  
Drive EN high to place the receiver(s) into a high-  
impedance state. Receivers can be either active or  
inactive in shutdown (Table 1).  
The MAX3222E/MAX3237E/MAX3241E/MAX3246E  
transmitters are disabled and the outputs are forced  
LapLink is a trademark of Traveling Software.  
_______________________________________________________________________________________  
9
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
V
CC  
5V/div  
0
SHDN  
T2OUT  
PREVIOUS  
RS-232  
V
CC  
PROTECTION  
2V/div  
0
DIODE  
Rx  
5k  
UART  
T1OUT  
Tx  
V
CC  
= 3.3V  
GND  
C1–C4 = 0.1µF  
SHDN = GND  
40µs/div  
Figure 3. Transmitter Outputs Recovering from Shutdown or  
Powering Up  
a) OLDER RS-232: POWERED-DOWN UART DRAWS CURRENT FROM  
A ACTIVE RECEIVER OUTPUT IN SHUTDOWN.  
V
CC  
TO  
µP  
MAX3222E/MAX3237E/MAX3241E/  
MAX3246E ꢁhutdown Mode  
Supplꢅ current falls to less than 1µA in shutdown mode  
(SHDN = low). The MAX3237E’s supplꢅ current falls  
to10nA (tꢅp) when all receiver inputs are in the invalid  
range (-0.3V < R_IN < +0.3). When shut down, the  
device’s charge pumps are shut off, V+ is pulled down  
to V , V- is pulled to ground, and the transmitter out-  
ꢁꢁ  
puts are disabled (high impedance). The time required  
to recover from shutdown is tꢅpicallꢅ 100µs, as shown  
LOGIC  
TRANSITION  
DETECTOR  
MAX3237E/MAX3241E  
R1OUTB  
V
CC  
PROTECTION  
DIODE  
R1IN  
Rx  
R1OUT  
THREE-STATED  
in Figure 3. ꢁonnect SHDN to V  
if shutdown mode is  
ꢁꢁ  
EN = V  
CC  
5kΩ  
not used. SHDN has no effect on R_OUT or R_OUTꢄ  
UART  
(MAX3237E/MAX3241E).  
T1OUT  
T1IN  
Tx  
1ꢀ5k EꢁD ꢂrotection  
As with all Maxim devices, ESD-protection structures  
are incorporated to protect against electrostatic dis-  
charges encountered during handling and assemblꢅ.  
The driver outputs and receiver inputs of the  
MAX3222E/MAX3232E/MAX3237E/MAX3241E/MAX3246E  
have extra protection against static electricitꢅ. Maxim’s  
engineers have developed state-of-the-art structures to  
protect these pins against ESD of ±1ꢀ5V without damage.  
The ESD structures withstand high ESD in all states:  
normal operation, shutdown, and powered down. After  
an ESD event, Maxim’s E versions 5eep wor5ing without  
latchup, whereas competing RS-232 products can latch  
and must be powered down to remove latchup.  
GND  
SHDN = GND  
b) NEW MAX3237E/MAX3241E: EN SHUTS DOWN RECEIVER OUTPUTS  
B (EXCEPT FOR B OUTPUTS), SO NO CURRENT FLOWS TO UART IN SHUTDOWN.  
B B OUTPUTS INDICATE RECEIVER ACTIVITY DURING SHUTDOWN WITH EN HIGH.  
Figure 2. Detection of RS-232 Activity when the UART and  
Interface are Shut Down; Comparison of MAX3237E/MAX3241E  
(b) with Previous Transceivers (a)  
The complementarꢅ outputs on the MAX3237E/  
MAX3241E (R_OUTꢄ) are alwaꢅs active, regardless of the  
state of EN or SHDN. This allows the device to be used  
for ring indicator applications without forward biasing  
other devices connected to the receiver outputs. This is  
ideal for sꢅstems where V  
to accommodate peripherals such as UARTs (Figure 2).  
Furthermore, the MAX3237E logic I/O pins also have  
±1ꢀ5V ESD protection. Protecting the logic I/O pins to  
±1ꢀ5V ma5es the MAX3237E ideal for data cable  
applications.  
drops to zero in shutdown  
ꢁꢁ  
10 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ESD protection can be tested in various waꢅs% the  
Table 1. MAX3222E/MAX3237E/MAX3241E/  
MAX3246E Shutdown and Enable Control  
Truth Table  
transmitter outputs and receiver inputs for the  
MAX3222E/MAX3232E/MAX3241E/MAX3246E are  
characterized for protection to the following limits:  
±1ꢀ5V using the ꢃuman ꢄodꢅ Model  
R_OUTB  
(MAX3237E/  
MAX3241E)  
SHDN  
EN  
T_OUT  
R_OUT  
±85V using the ꢁontact Discharge method specified  
in IEꢁ 1000-4-2  
0
0
1
1
0
1
0
1
ꢃigh-Z  
ꢃigh-Z  
Active  
Active  
Active  
ꢃigh-Z  
Active  
ꢃigh-Z  
Active  
Active  
Active  
Active  
±±5V (MAX3246E onlꢅ) using the ꢁontact Discharge  
method specified in IEꢁ 1000-4-2  
±1ꢀ5V using the Air-ꢂap Discharge method speci-  
fied in IEꢁ 1000-4-2  
R
R
C
D
1MΩ  
1500Ω  
DISCHARGE  
RESISTANCE  
I
100%  
90%  
PEAK-TO-PEAK RINGING  
(NOT DRAWN TO SCALE)  
CHARGE-CURRENT  
LIMIT RESISTOR  
I
P
r
HIGH-  
VOLTAGE  
DC  
AMPERES  
DEVICE  
UNDER  
TEST  
C
100pF  
STORAGE  
CAPACITOR  
s
36.8%  
SOURCE  
10%  
0
TIME  
0
t
RL  
t
DL  
CURRENT WAVEFORM  
Figure 4b. Human Body Model Current Waveform  
Figure 4a. Human Body ESD Test Model  
I
100%  
R
R
D
330Ω  
C
90%  
50Mto 100MΩ  
DISCHARGE  
RESISTANCE  
CHARGE-CURRENT  
LIMIT RESISTOR  
HIGH-  
VOLTAGE  
DC  
DEVICE  
UNDER  
TEST  
C
s
150pF  
STORAGE  
CAPACITOR  
SOURCE  
10%  
t
t = 0.7ns to 1ns  
r
30ns  
60ns  
Figure 5a. IEC 1000-4-2 ESD Test Model  
Figure 5b. IEC 1000-4-2 ESD Generator Current Waveform  
______________________________________________________________________________________ 11  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
Table 2. Required Minimum Capacitor  
Values  
6
5
VCC  
(V)  
C1  
(µF)  
C2, C3, C4  
(µF)  
V
OUT+  
4
3
V
CC  
= 3.0V  
2
MAX3222E/MAX3232E/MAX3241E  
V
V
1
OUT+  
3.0 to 3.6  
4.ꢀ to ꢀ.ꢀ  
0.1  
0.047  
0.1  
0.1  
0
0.33  
0.47  
-1  
-2  
-3  
-4  
-5  
-6  
3.0 to ꢀ.ꢀ  
V
CC  
1
OUT-  
MAX3237E/MAX3246E  
3.0 to 3.6  
V
OUT-  
0.22  
0.1  
0.22  
0.1  
3.1ꢀ to 3.6  
0
2
3
4
5
6
7
8
9
10  
4.ꢀ to ꢀ.ꢀ  
0.047  
0.22  
0.33  
1.0  
LOAD CURRENT PER TRANSMITTER (mA)  
3.0 to ꢀ.ꢀ  
Figure 6a. MAX3241E Transmitter Output Voltage vs. Load  
Current Per Transmitter  
Table 3. Logic-Family Compatibility with  
Various Supply Voltages  
IEC 1000-4-2  
SYSTEM  
V
CC  
SUPPLY  
VOLTAGE  
(V)  
The IEꢁ 1000-4-2 standard covers ESD testing and  
performance of finished equipment% it does not specifi-  
callꢅ refer to integrated circuits. The MAX3222E/  
MAX3232E/MAX3237E/MAX3241E/MAX3246E help ꢅou  
design equipment that meets level 4 (the highest level)  
of IEꢁ 1000-4-2, without the need for additional ESD-  
protection components.  
POWER-SUPPLY  
VOLTAGE  
(V)  
COMPATIBILITY  
ꢁompatible with all  
ꢁMOS families  
3.3  
3.3  
ꢁompatible with all  
TTL and ꢁMOS  
families  
The major difference between tests done using the  
ꢃuman ꢄodꢅ Model and IEꢁ 1000-4-2 is higher pea5  
current in IEꢁ 1000-4-2, because series resistance is  
lower in the IEꢁ 1000-4-2 model. ꢃence, the ESD with-  
stand voltage measured to IEꢁ 1000-4-2 is generallꢅ  
lower than that measured using the ꢃuman ꢄodꢅ  
Model. Figure ꢀa shows the IEꢁ 1000-4-2 model, and  
Figure ꢀb shows the current waveform for the ±85V IEꢁ  
1000-4-2 level 4 ESD ꢁontact Discharge test. The Air-  
ꢂap Discharge test involves approaching the device  
with a charged probe. The ꢁontact Discharge method  
connects the probe to the device before the probe is  
energized.  
ꢁompatible with AꢁT  
and ꢃꢁT ꢁMOS, and  
with Aꢁ, ꢃꢁ, or  
3.3  
ꢁD4000 ꢁMOS  
For the MAX3237E, all logic and RS-232 I/O pins are  
characterized for protection to ±1ꢀ5V per the ꢃuman  
ꢄodꢅ Model.  
EꢁD Test Conditions  
ESD performance depends on a varietꢅ of conditions.  
ꢁontact Maxim for a reliabilitꢅ report that documents  
test setup, test methodologꢅ, and test results.  
Machine Model  
The Machine Model for ESD tests all pins using a  
200pF storage capacitor and zero discharge resis-  
tance. Its objective is to emulate the stress caused bꢅ  
contact that occurs with handling and assemblꢅ during  
manufacturing. All pins require this protection during  
manufacturing, not just RS-232 inputs and outputs.  
Therefore, after Pꢁ board assemblꢅ, the Machine  
Model is less relevant to I/O ports.  
Human Body Model  
Figure 4a shows the ꢃuman ꢄodꢅ Model, and Figure  
4b shows the current waveform it generates when dis-  
charged into a low impedance. This model consists of  
a 100pF capacitor charged to the ESD voltage of interest,  
which is then discharged into the test device through a  
1.ꢀ5resistor.  
12 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
V
CC  
= +3.0V TO +5.5V  
C
BYPASS  
26  
27  
3
28  
V
CC  
C1+  
V+  
V-  
C1  
C3  
C4  
24  
C1-  
COMPUTER SERIAL PORT  
1
C2+  
MAX3241E  
C2  
2
C2-  
9
T1IN  
14  
13  
T1OUT  
T2OUT  
T3OUT  
+V  
+V  
T2IN  
10  
11  
T3IN  
12  
21  
V
CC  
-V  
R1OUTB  
GND  
Tx  
20  
19  
R2OUTB  
R1OUT  
R1IN  
R2IN  
R3IN  
R4IN  
4
5
6
5kΩ  
18  
17  
16  
R2OUT  
R3OUT  
5kΩ  
5kΩ  
5kΩ  
5kΩ  
7
R4OUT  
R5OUT  
EN  
MOUSE  
15  
23  
R5IN  
8
22  
SHDN  
V
CC  
GND  
25  
Figure 6b. Mouse Driver Test Circuit  
excessivelꢅ with temperature. If in doubt, use capaci-  
tors with a larger nominal value. The capacitor’s equiv-  
alent series resistance (ESR), which usuallꢅ rises at low  
temperatures, influences the amount of ripple on V+  
and V-.  
Applications Information  
Capacitor ꢁelection  
The capacitor tꢅpe used for ꢁ1–ꢁ4 is not critical for  
proper operation% polarized or nonpolarized capacitors  
can be used. The charge pump requires 0.1µF capaci-  
tors for 3.3V operation. For other supplꢅ voltages, see  
Table 2 for required capacitor values. Do not use val-  
ues smaller than those listed in Table 2. Increasing the  
capacitor values (e.g., bꢅ a factor of 2) reduces ripple  
on the transmitter outputs and slightlꢅ reduces power  
consumption. ꢁ2, ꢁ3, and ꢁ4 can be increased without  
changing ꢁ1’s value. However, do not increase C1  
without also increasing the values of C2, C3, C4,  
ꢂower-ꢁupply Decoupling  
In most circumstances, a 0.1µF V  
bꢅpass capacitor  
ꢁꢁ  
is adequate. In applications sensitive to power-supplꢅ  
noise, use a capacitor of the same value as charge-  
pump capacitor ꢁ1. ꢁonnect bꢅpass capacitors as  
close to the Iꢁ as possible.  
Operation Down to 2.7k  
Transmitter outputs meet EIA/TIA-ꢀ62 levels of ±3.7V  
with supplꢅ voltages as low as 2.7V.  
and C  
to maintain the proper ratios (C1 to  
the other capacitors).  
BYPASS  
When using the minimum required capacitor values,  
ma5e sure the capacitor value does not degrade  
______________________________________________________________________________________ 13  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
the transmitters are enabled onlꢅ when the magnitude  
of V- exceeds approximatelꢅ -3.0V.  
Transmitter Outputs Recovering  
from ꢁhutdown  
Figure 3 shows two transmitter outputs recovering from  
shutdown mode. As theꢅ become active, the two trans-  
mitter outputs are shown going to opposite RS-232 levels  
(one transmitter input is high% the other is low). Each  
transmitter is loaded with 35in parallel with 2ꢀ00pF.  
The transmitter outputs displaꢅ no ringing or undesir-  
able transients as theꢅ come out of shutdown. Note that  
Mouse Drivability  
The MAX3241E is designed to power serial mice while  
operating from low-voltage power supplies. It has  
been tested with leading mouse brands from manu-  
facturers such as Microsoft and Logitech. The  
MAX3241E successfullꢅ drove all serial mice tested  
and met their current and voltage requirements.  
V
CC  
0.1µF  
5V/div  
5V/div  
5V/div  
T1IN  
T1OUT  
R1OUT  
V
CC  
C1+  
V+  
V-  
C3  
C4  
C1  
C1-  
C2+  
MAX3222E  
MAX3232E  
MAX3237E  
MAX3241E  
MAX3246E  
C2  
C2-  
V
CC  
= 3.3V, C1–C4 = 0.1µF  
T_ OUT  
T_ IN  
2µs/div  
R_ IN  
R_ OUT  
Figure 9. MAX3241E Loopback Test Result at 250kbps  
5kΩ  
1000pF  
GND  
+5V  
T_IN  
0
Figure 7. Loopback Test Circuit  
+5V  
0
-5V  
+5V  
0
T_OUT  
5k+ 250pF  
V
= 3.3V  
CC  
C1–C4 = 0.1µF  
R_OUT  
5V/div  
T1IN  
400ns/div  
5V/div  
5V/div  
T1OUT  
Figure 10. MAX3237E Loopback Test Result at 1000kbps  
(MBAUD = V  
)
CC  
R1OUT  
V
CC  
= 3.3V  
C1–C4 = 0.1µF  
2µs/div  
Figure 8. MAX3241E Loopback Test Result at 120kbps  
14 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
Figure 6a shows the transmitter output voltages under  
increasing load current at +3.0V. Figure 6b shows a  
tꢅpical mouse connection using the MAX3241E.  
UCꢁꢂ Reliability  
The UꢁSP represents a unique pac5aging form factor  
that maꢅ not perform equallꢅ to a pac5aged product  
through traditional mechanical reliabilitꢅ tests. UꢁSP  
reliabilitꢅ is integrallꢅ lin5ed to the user’s assemblꢅ  
methods, circuit board material, and usage environ-  
ment. The user should closelꢅ review these areas when  
considering use of a UꢁSP pac5age. Performance  
through Operating Life Test and Moisture Resistance  
remains uncompromised as the wafer-fabrication  
process primarilꢅ determines it.  
High Data Rates  
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/  
MAX3246E maintain the RS-232 ±V minimum transmit-  
ter output voltage even at high data rates. Figure 7  
shows a transmitter loopbac5 test circuit. Figure 8  
shows a loopbac5 test result at 1205bps, and Figure ±  
shows the same test at 2ꢀ05bps. For Figure 8, all trans-  
mitters were driven simultaneouslꢅ at 1205bps into RS-  
232 loads in parallel with 1000pF. For Figure ±, a single  
transmitter was driven at 2ꢀ05bps, and all transmitters  
were loaded with an RS-232 receiver in parallel with  
1000pF.  
Mechanical stress performance is a greater considera-  
tion for a UꢁSP pac5age. UꢁSPs are attached through  
direct solder contact to the user’s Pꢁ board, foregoing  
the inherent stress relief of a pac5aged product lead  
frame. Solder joint contact integritꢅ must be consid-  
ered. Table 4 shows the testing done to characterize  
the UꢁSP reliabilitꢅ performance. In conclusion, the  
UꢁSP is capable of performing reliablꢅ through envi-  
ronmental stresses as indicated bꢅ the results in the  
table. Additional usage data and recommendations are  
detailed in the UꢁSP application note, which can be  
found on Maxim’s website at www.maxim-ic.com.  
The MAX3237E maintains the RS-232 ±.0V minimum  
transmitter output voltage at data rates up to 1Mbps.  
Figure 10 shows a loopbac5 test result at 1Mbps with  
MꢄAUD = V . For Figure 10, all transmitters were  
ꢁꢁ  
loaded with an RS-232 receiver in parallel with 2ꢀ0pF.  
Interconnection with 3k and ꢀk Logic  
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/  
MAX3246E can directlꢅ interface with various ꢀV logic  
families, including AꢁT and ꢃꢁT ꢁMOS. See Table 3  
for more information on possible combinations of inter-  
connections.  
Table 4. Reliability Test Data  
FAILURES PER  
DURATION  
TEST  
CONDITIONS  
SAMPLE SIZE  
T
A
T
A
= -3ꢀ°ꢁ to +8ꢀ°ꢁ,  
= -40°ꢁ to +100°ꢁ  
1ꢀ0 cꢅcles,  
±00 cꢅcles  
0/10,  
0/200  
Temperature ꢁꢅcle  
Operating Life  
T
T
T
T
= +70°ꢁ  
240 hours  
240 hours  
240 hours  
24 hours  
0/10  
0/10  
0/10  
0/10  
0/1ꢀ  
0/ꢀ  
A
A
A
A
Moisture Resistance  
Low-Temperature Storage  
Low-Temperature Operational  
Solderabilitꢅ  
= +20°ꢁ to +60°ꢁ, ±0ꢆ Rꢃ  
= -20°ꢁ  
= -10°ꢁ  
8-hour steam age  
ESD  
1ꢀ5V, ꢃuman ꢄodꢅ Model  
ꢃigh-Temperature Operating  
Life  
T = +1ꢀ0°ꢁ  
J
168 hours  
0/4ꢀ  
______________________________________________________________________________________ 15  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
__________________________________________________________ꢂin Configurations  
TOP VIEW  
N.C.  
C1+  
V+  
1
2
N.C.  
EN  
C1+  
V+  
20  
19  
18  
17  
16  
15  
14  
13  
12  
11  
1
2
3
4
5
6
7
8
9
SHDN  
1
2
3
4
5
6
7
8
C1+  
V+  
V
CC  
18  
17  
16  
15  
14  
13  
12  
11  
EN  
C1+  
V+  
1
2
SHDN  
20  
19  
18  
17  
16  
15  
14  
13  
12  
11  
16  
15  
14  
V
CC  
V
CC  
GND  
V
CC  
GND  
3
GND  
C1-  
T1OUT  
GND  
3
T1OUT  
R1IN  
C1-  
4
T1OUT  
R1IN  
C1-  
T1OUT  
R1IN  
R1OUT  
N.C.  
MAX3232E  
C1-  
4
C2+  
C2-  
13 R1IN  
12 R1OUT  
11 T1IN  
MAX3232E  
MAX3222E  
MAX3222E  
C2+  
C2-  
5
C2+  
C2-  
C2+  
C2-  
5
R1OUT  
T1IN  
6
R1OUT  
T1IN  
6
V-  
V-  
7
V-  
V-  
10  
9
7
T2OUT  
R2IN  
T2IN  
T2OUT  
T2IN  
8
T2IN  
T2OUT  
R2IN  
T2OUT  
T1IN  
R2OUT  
8
R2OUT  
N.C.  
R2IN  
N.C.  
9
10 R2OUT  
T2IN  
R2IN  
9
SO/DIP/SSOP/TSSOP  
R2OUT  
10  
N.C.  
10  
SO/DIP  
TSSOP  
TSSOP/SSOP  
TOP VIEW  
28  
28  
27  
26  
25  
24  
23  
22  
1
2
1
2
3
4
5
6
7
8
9
C2+  
C2-  
C2+  
GND  
C1+  
V+  
C1+  
27  
26  
V+  
V
C2-  
V-  
3
CC  
V
CC  
R1IN  
R2IN  
1
2
3
4
5
6
7
8
24 GND  
V-  
25 C1-  
4
R1IN  
R2IN  
R3IN  
R4IN  
R5IN  
T1OUT  
GND  
C1-  
23 C1-  
T1IN  
T1OUT  
T2OUT  
T3OUT  
5
24  
23  
MAX3237E  
MAX3241E  
R3IN  
22 EN  
6
T2IN  
EN  
R4IN  
21 SHDN  
20 R1OUTB  
19 R2OUTB  
18 R1OUT  
17 R2OUT  
7
22 T3IN  
21  
SHDN  
MAX3241E  
R5IN  
21 R1OUTB  
R1IN  
R2IN  
8
R1OUT  
T1OUT  
T2OUT  
T3OUT  
20  
19  
20  
19  
R2OUTB  
R1OUT  
9
R2OUT  
T4IN  
10  
11  
12  
13  
14  
T2OUT 10  
T4OUT  
R3IN  
18 R3OUT T3OUT  
18 R2OUT  
17 R3OUT  
16 R4OUT  
11  
12  
13  
14  
T5IN  
17  
T5OUT  
EN  
T3IN  
T2IN  
T1IN  
16 R1OUTB  
15  
15  
MBAUD  
R5OUT  
SHDN  
SSOP  
SSOP/SO/TSSOP  
QFN  
16 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂin Configurations (continued)  
TOP VIEW  
TOP VIEW  
15  
14  
13  
12  
11  
12  
11  
10  
9
T2IN  
N.C.  
10  
9
GND 16  
17  
SHDN 18  
T2IN  
8
7
6
5
GND 13  
V
CC  
V
14  
15  
16  
R2OUT  
R2IN  
CC  
8
R2OUT  
R2IN  
MAX3222E  
MAX3232E  
V+  
EN  
7
19  
20  
EXPOSED  
PADDLE  
EXPOSED  
PADDLE  
T2OUT  
C1+  
6
T2OUT  
V+  
1
2
3
4
5
1
2
3
4
TQFN  
TQFN  
TOP VIEW  
(BUMPS ON BOTTOM)  
B2: SHDN  
C2: R1OUT  
D2: T3IN  
E2: T2IN  
B3: EN  
R4OUT R5OUT  
R1IN  
A4  
R2IN  
A5  
A1  
A2  
B2  
C2  
D2  
E2  
F2  
A3  
A6 R3IN  
R3OUT  
E3: T1IN  
BUMPS B4, B5, C3, C4,  
C5, D3, D4, D5, E4, AND  
E5 NOT POPULATED  
R2OUT B1  
B3  
B6 R4IN  
C6  
C1  
V-  
R5IN  
MAX3246E  
C2-  
C2+  
V+  
D6 T3OUT  
D1  
E1  
F1  
E3  
E6  
T2OUT  
F3  
F4  
F5  
F6 T1OUT  
V
C1+  
C1-  
GND  
CC  
UCSP  
______________________________________________________________________________________ 17  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
__________________________________________________Typical Operating Circuits  
+3.3V  
+3.3V  
17  
16  
C
C
BYPASS  
BYPASS  
V
V
CC  
CC  
3
7
2
4
5
6
2
6
1
3
4
5
C1+  
C1+  
V+  
V+  
C1  
0.1µF  
C1  
0.1µF  
C3*  
C3*  
0.1µF  
0.1µF  
C1-  
C2+  
C1-  
C2+  
MAX3222E  
MAX3232E  
V-  
V-  
C2  
0.1µF  
C2  
0.1µF  
C4  
0.1µF  
C4  
0.1µF  
C2-  
C2-  
12  
T1OUT  
T1IN  
15  
8
11  
T1OUT  
T1IN  
14  
7
TTL/CMOS  
INPUTS  
RS-232  
OUTPUTS  
TTL/CMOS  
INPUTS  
RS-232  
OUTPUTS  
T2IN  
T2OUT  
R1IN  
11  
T2IN  
T2OUT  
R1IN  
10  
14  
9
13 R1OUT  
10 R2OUT  
13  
8
12 R1OUT  
TTL/CMOS  
OUTPUTS  
TTL/CMOS  
OUTPUTS  
RS-232  
INPUTS  
5kΩ  
RS-232  
INPUTS  
5kΩ  
R2IN  
9
R2OUT  
R2IN  
5kΩ  
5kΩ  
EN  
1
18  
SHDN  
GND  
16  
GND  
15  
*C3 CAN BE RETURNED TO EITHER V OR GROUND.  
CC  
NOTE: PIN NUMBERS REFER TO SO/DIP PACKAGES.  
MAX3222E PINOUT REFERS TO SO/DIP PACKAGES.  
MAX3232E PINOUT REFERS TO TSSOP/SSOP/SO/DIP/ PACKAGES  
SEE TABLE 2 FOR CAPACITOR SELECTION.  
18 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
_____________________________________Typical Operating Circuits (continued)  
+3.3V  
+3.3V  
C
C
BYPASS  
BYPASS  
26  
26  
V
V
CC  
CC  
27  
4
27  
3
28  
28  
C1+  
C1+  
V+  
V-  
V+  
C1  
0.1µF  
C3*  
0.1µF  
C3*  
25  
1
24  
1
0.1µF  
C1-  
C2+  
C1-  
C2+  
0.1µF  
MAX3237E  
MAX3241E  
V-  
C2  
0.1µF  
0.1µF  
0.1µF  
C4  
0.1µF  
3
2
C2-  
C2-  
T1IN  
T1IN  
T1OUT  
T2OUT  
T3OUT  
5
6
7
T1OUT  
9
24  
14  
13  
T1  
T2  
T2IN  
T3IN  
T2IN  
T2OUT 10  
23  
22  
TTL/CMOS  
INPUTS  
RS-232  
OUTPUTS  
T3IN  
12  
21  
11  
RS-232  
OUTPUTS  
T3OUT  
R1IN  
LOGIC  
INPUTS  
T3  
T4  
T5  
R1OUTB  
T4IN  
T5IN  
T4OUT 10  
19  
17  
R2OUTB  
R1OUT  
20  
19  
12  
T5OUT  
R1IN  
4
5
R1OUTB  
R1OUT  
16  
21  
5kΩ  
R2OUT  
R3OUT  
R4OUT  
R2IN  
18  
17  
16  
8
9
R1  
R2  
R3  
5kΩ  
TTL/CMOS  
OUTPUTS  
5kΩ  
R2IN  
6
7
8
R3IN  
RS-232  
INPUTS  
RS-232  
INPUTS  
R2OUT  
R3OUT  
20  
18  
LOGIC  
5kΩ  
OUTPUTS  
5kΩ  
R3IN  
R4IN  
11  
5kΩ  
5kΩ  
R5OUT  
EN  
15  
23  
R5IN  
15  
14  
5kΩ  
MBAUD  
SHDN  
EN  
13  
22  
SHDN  
GND  
2
GND  
25  
*C3 CAN BE RETURNED TO EITHER V OR GROUND.  
CC  
______________________________________________________________________________________ 19  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
_____________________________________Typical Operating Circuits (continued)  
+3.3V  
C
BYPASS  
F2  
V
CC  
F1  
F3  
C1+  
V+  
V-  
C1  
0.1µF  
C3*  
F4  
E1  
D1  
C1-  
C2+  
0.1µF  
MAX3246E  
C1  
C2  
0.1µF  
C4  
0.1µF  
C2-  
T1IN  
T1OUT F6  
T2OUT E6  
E3  
E2 T2IN  
RS-232  
OUTPUTS  
TTL/CMOS  
INPUTS  
T3IN  
D2  
C2  
D6  
A4  
T3OUT  
R1OUT  
R1IN  
5kΩ  
R2OUT  
R3OUT  
R4OUT  
R2IN A5  
B1  
A1  
A2  
5kΩ  
R3IN  
TTL/CMOS  
OUTPUTS  
A6  
B6  
RS-232  
INPUTS  
5kΩ  
R4IN  
5kΩ  
R5IN C6  
5kΩ  
SHDN  
R5OUT  
EN  
A3  
B3  
B2  
GND  
F5  
*C3 CAN BE RETURNED TO EITHER V OR GROUND.  
CC  
20 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢁelector Guide  
Ordering Information (continued)  
NO. OF  
DRIVERS/  
RECEIVERS  
GUARANTEED  
DATA RATE  
(bps)  
PIN-  
PKG  
CODE  
LOW-POWER  
SHUTDOWN  
PART  
TEMP RANGE  
PACKAGE  
PART  
16 Thin QFN-  
MAX3232EꢁTE  
0°ꢁ to +70°ꢁ EP** (ꢀmm x  
ꢀmm)  
T16ꢀꢀ-2  
MAX3222E  
MAX3232E  
2/2  
2/2  
2ꢀ05  
2ꢀ05  
MAX3232EꢁUE  
MAX3232EꢁUP  
MAX3232EEAE  
MAX3232EEWE  
MAX3232EEPE  
0°ꢁ to +70°ꢁ 16 TSSOP  
0°ꢁ to +70°ꢁ 20 TSSOP  
-40°ꢁ to +8ꢀ°ꢁ 16 SSOP  
-40°ꢁ to +8ꢀ°ꢁ 16 Wide SO  
-40°ꢁ to +8ꢀ°ꢁ 16 Plastic DIP  
16 Thin QFN-  
MAX3237E  
(Normal)  
ꢀ/3  
ꢀ/3  
2ꢀ05  
1M  
MAX3237E  
(Megaꢄaud)  
MAX3241E  
MAX3246E  
3/ꢀ  
3/ꢀ  
2ꢀ05  
2ꢀ05  
EP** (ꢀmm x  
ꢀmm)  
MAX3232EETE  
-40°ꢁ to +8ꢀ°ꢁ  
T16ꢀꢀ-2  
MAX3232EEUE  
MAX3232EEUP  
MAX3237EꢁAI  
MAX3237EEAI  
MAX3241EꢁAI  
MAX3241EꢁWI  
MAX3241EꢁUI  
MAX3241EꢁTJ  
MAX3241EEAI  
MAX3241EEWI  
MAX3241EEUI  
-40°ꢁ to +8ꢀ°ꢁ 16 TSSOP  
-40°ꢁ to +8ꢀ°ꢁ 20 TSSOP  
0°ꢁ to +70°ꢁ 28 SSOP  
-40°ꢁ to +8ꢀ°ꢁ 28 SSOP  
0°ꢁ to +70°ꢁ 28 SSOP  
0°ꢁ to +70°ꢁ 28 Wide SO  
0°ꢁ to +70°ꢁ 28 TSSOP  
0°ꢁ to +70°ꢁ 32 Thin QFN  
-40°ꢁ to +8ꢀ°ꢁ 28 SSOP  
-40°ꢁ to +8ꢀ°ꢁ 28 Wide SO  
-40°ꢁ to +8ꢀ°ꢁ 28 TSSOP  
___________________Chip Information  
TRANSISTOR ꢁOUNT:  
MAX3222E/MAX3232E: 112±  
MAX3237E: 2110  
MAX3241E: 133ꢀ  
MAX3246E: 842  
PROꢁESS: ꢄIꢁMOS  
MAX3246EꢁꢄX-T 0°ꢁ to +70°ꢁ 6 x 6 UꢁSP*  
MAX3246EEꢄX-T -40°ꢁ to +8ꢀ°ꢁ 6 x 6 UꢁSP*  
*Requires solder temperature profile described in the Absolute  
Maximum Ratings section. UCSP Reliability is integrally linked  
to the user’s assembly methods, circuit board material, and  
environment. Refer to the UCSP Reliability Notice in the UCSP  
Reliability section of this datasheet for more information.  
______________________________________________________________________________________ 21  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂac5age Information  
(The pac5age drawing(s) in this data sheet maꢅ not reflect the most current specifications. For the latest pac5age outline information,  
go to www.maxim-ic.com/packages.)  
PACKAGE OUTLINE,  
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm  
1
E
21-0139  
2
PACKAGE OUTLINE,  
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm  
2
E
21-0139  
2
22 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂac5age Information  
(The pac5age drawing(s) in this data sheet maꢅ not reflect the most current specifications. For the latest pac5age outline information,  
go to www.maxim-ic.com/packages.)  
PACKAGE OUTLINE, TSSOP 4.40mm BODY  
1
21-0066  
G
1
______________________________________________________________________________________ 23  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂac5age Information (continued)  
(The pac5age drawing(s) in this data sheet maꢅ not reflect the most current specifications. For the latest pac5age outline information,  
go to www.maxim-ic.com/packages.)  
PACKAGE OUTLINE, 6x6 UCSP  
1
21-0082  
J
1
24 ______________________________________________________________________________________  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂac5age Information (continued)  
(The pac5age drawing(s) in this data sheet maꢅ not reflect the most current specifications. For the latest pac5age outline information,  
go to www.maxim-ic.com/packages.)  
INCHES  
MILLIMETERS  
N
MAX  
MAX  
2.65  
0.30  
0.49  
0.32  
DIM  
A
MIN  
MIN  
2.35  
0.10  
0.35  
0.23  
0.093  
0.004  
0.014  
0.009  
0.104  
0.012  
0.019  
0.013  
A1  
B
C
e
0.050  
1.27  
H
E
E
0.291  
0.394  
0.016  
0.299  
0.419  
0.050  
7.40  
10.00  
0.40  
7.60  
10.65  
1.27  
H
L
VARIATIONS:  
INCHES  
1
MILLIMETERS  
TOP VIEW  
DIM  
D
MIN  
MAX  
0.413  
0.463  
0.512  
0.614  
0.713  
MIN  
10.10  
11.35  
12.60  
15.20  
17.70  
MAX  
N MS013  
0.398  
0.447  
0.496  
0.598  
0.697  
10.50 16 AA  
11.75 18 AB  
13.00 20 AC  
15.60 24 AD  
18.10 28 AE  
D
D
D
D
D
C
A
B
e
0-8∞  
A1  
L
FRONT VIEW  
SIDE VIEW  
PROPRIETARY INFORMATION  
TITLE:  
PACKAGE OUTLINE, .300" SOIC  
APPROVAL  
DOCUMENT CONTROL NO.  
REV.  
1
21-0042  
B
1
______________________________________________________________________________________ 25  
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,  
Up to 1Mbps, True Rꢁ-232 Transceivers  
ꢂac5age Information (continued)  
(The pac5age drawing(s) in this data sheet maꢅ not reflect the most current specifications. For the latest pac5age outline information,  
go to www.maxim-ic.com/packages.)  
PACKAGE OUTLINE, TSSOP 4.40mm BODY  
1
21-0066  
G
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are  
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.  
26 ____________________Maxim Integrated ꢂroducts, 120 ꢁan Gabriel Drive, ꢁunnyvale, CA 94086 408-737-7600  
© 200ꢀ Maxim Integrated Products  
Printed USA  
is a registered trademar5 of Maxim Integrated Products, Inc.  

相关型号:

MAX3241ECGJ

【15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM

MAX3241ECGJ-T

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, QFN-32
MAXIM

MAX3241ECTJ

【15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM

MAX3241ECUI

【15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM

MAX3241ECUI+T

暂无描述
MAXIM

MAX3241ECUI-T

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, 4.40 MM, MO-153AE, TSSOP-28
MAXIM

MAX3241ECWI

Transceiver
MAXIM

MAX3241ECWI+

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, ROHS COMPLIANT, SOIC-28
MAXIM

MAX3241ECWI+T

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, LEAD FREE, SO-28
MAXIM

MAX3241EEAI

LINE TRANSCEIVER|CMOS|3 DRIVER|5 RCVR|SSOP|28PIN|PLASTIC
MAXIM

MAX3241EEAI+

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, ROHS COMPLIANT, SSOP-28
MAXIM

MAX3241EEAITG002

Line Transceiver, 3 Func, 3 Driver, 5 Rcvr, BICMOS, PDSO28, 5.30 MM, MO-150, SSOP-28
MAXIM