CSM162 [MAXWELL]
Logic IC Output Optocoupler,;
| 型号： | CSM162 |
| 厂家： | 
MAXWELL TECHNOLOGIES |
| 描述： | Logic IC Output Optocoupler, 输出元件 光电 |
| 文件： | 总12页 (文件大小：385K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
®
ISOCOM LTD
IECQ
QC 88000-C003
ISSUE 8
COMPONENT
SPECIFICATION
May 2013
Component Specification
For
Ceramic Hermetically Sealed
High Gain Optocouplers
M1077 IECQ
IECQ Product Certificate Number E1280/F
Up-to-date lists and bibliographical references of IECQ publications may be downloaded from www.iecq.org
Further copies of this document may be obtained from:
IEC
International Electrotechnical Commission
Commission Electrotechnique Internationale
Box 131, rue de Varembé, CH 1211 Geneva 20, Switzerland
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 1 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
FOREWORD
The IECQ Quality Assessment System for Electronic Components (IECQ) is composed of those member countries of
the International Electrotechnical Commission (IEC) who wish to take part in a harmonized system for electronic
components of assessed quality. IECQ is also known in some European member countries as IECQ-CECC.
The object of the System is to facilitate international trade by the harmonization of the specifications and quality
assessment procedures for electronic components, and by the grant of an internationally recognised Mark, or
Certificate of Conformity. The components produced or services provided under the system are thereby acceptable in
all member countries without further testing.
This Component Specification is based upon the requirements of IECQ 03-3, Annex E (QC 001002-2 Amendment 1,
Clause 5.4) and has been prepared by:
Isocom Ltd
48 Hutton Close
Crowther Industrial Estate
Washington
Tyne and Wear
NE38 0AH
United Kingdom
Tel:
Fax:
+44 0191 4166 546
+44 0191 4155 055
and published under the authority of:
BSI Group
Kitemark Court
Davy Avenue
Knowlhill
Milton Keynes
MK5 8PP
United Kingdom
AMENDMENT RECORD
Issue 1 – Changed Pages 4, 9 & 10 – Amendments 22/06/09
Issue 2 – Changed Pages 3, 4 & 5 – Amendments 05/07/10
Issue 3 – Changed Pages 3, 4, 5 & 6 – RoHS Compliant, Added CSM160/161/162-2 & Amendments 13/07/10
Issue 4 – Changed Pages 3,4,9 and 10 – Added CH390 23/08/10
Issue 5 – Changed Page 6 – Added 4/5 pin hybrid package 26/5/11
Issue 6 – Changed Page 9 – IF changed to 2mA for ICCL for CSM160/1 9/11/11
Issue 7 –Re-issued 30/5/13
REQUIREMENTS
The requirements for IECQ Component Specifications as detailed in IECQ 03-3, Annex E (QC 001002-2 Amendment
1, Clause 5.4) are satisfied by the following data sheet.
It should note that IECQ are not responsible for manufacturers declarations made in data sheets which fall outside the
limits of approved detailed in IECQ certificates.
This Component Specification is intended for use with applicable IECQ Assessment Specifications. Eg: QC 88000-
A0001
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 2 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Ceramic Hermetically Sealed High Gain Optocouplers
■ 6N140A
■ CD750
■ CD5731
■ CH370
■ CH390
■ CS700
■ CS5700
■ CSM141/A
■ CSM160/161/162-2
■ CSM160/161/162-4
■ CSM1700
Features
Applications
▪ Release to IECQ
▪ Military, Space
▪ Hermetically Sealed
▪ Medical instruments
▪ Mos, Cmos Applications
▪ Logic Interfacing
▪ Data Transmission
▪ Transportation
▪ High Density Packaging
▪ 1500V DC withstand Test Voltage
▪ Low Input Requirements: 0.5mA
▪ High Current Transfer Ratio: 1000% Typical
▪ RoHS Compliant
Description
Each channel contains a light emitting diode which is optically coupled to an integrated high gain
photon detector. The high gain output stage features an open collector output providing both lower
saturation voltage and higher signalling speed than a conventional Photo-Darlington optocoupler.
The supply voltage can be operated as low as 2.0V without adversely affecting the parametric
performance. The High Current Transfer Ratio of the optocouplers makes them ideal for low input
current, min 0.5mA, applications.
The radiation immunity of the optocouplers compared to conventional photo transistor optocouplers
is due to the shallow depth and small junctions offered by the IC process.
The optocoupler family is also available in various package styles including 6, 8 and 16 pin DIP
through hole, 16 pin surface mount DIP flat pack and a 6 Pin leadless ceramic chip carrier. The
devices can be purchased with lead bend and plating options.
ISOCOM optocouplers are offered on the basis of similarity of emitter and detector therefore the
performance characterization is identical, subject to the limitations of the packages. The wafer die
similarities apply to the optocouplers for high reliability screening and radiation testing.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 3 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Selection Guide Package Styles and Configuration Options
5 pin
Hybrid
10 pin
Hybrid
16 pin
Flat Pack
Package
Lead Style
6 Pad LCC
8 pin DIP
8 pin DIP
16 pin DIP
1
2
Channels
1
1
2
4
2/4
Common Channel
Wiring
Isocom Part Numbers and Options
CSM141A
CSM1700
CS5700
CS700
CD750
CD5731
CSM160/161/
162
Commercial
CH370
CH390
6N140A
CSM141A/L2
CSM1700/L2
CS5700/L2
CS700/L2
CD750/L2
CD5731/L2
CD750/L2S
CD5731/L2S
CSM160/161/
162/L2
CSM160/161/
162/L2S
Defense Level
CH370/L2
CH390/L2
6N140A/L2
6N140A/L2S
CSM141A/L2S CS5700/L2S
CH370/L2S CH390/L2S CSM1700/L2S CS700/L2S
Space Level
Standard Gold Plate
Finish
Gold Plate
Option 20
Gold Plate
Option 20
Option 10
Option 30
Option 60
Gold Plate
Option 20
Option 10
Option 30
Option 60
Gold Plate
Option 20
Option 10
Option 30
Option 60
Gold Plate
Option 20
Solder Dipped
Butt Cut/Gold Plate
Gull Wing/Soldered
Crew Cut/Gold Plate
Functional Diagrams
CS5700
CS700
CD750
CD5731
CSM160/161
/162-2
CH370
CSM141A
6N140A
5 pin Hybrid
1 Channel
6 Pad LCC
1 Channel
8 pin DIP
1 Channel
8 pin DIP
2 Channel
16 pin DIP
4 Channel
16 pin Flat Pack
2 Channel
6
1
2
5
4
3
CSM160/161
/162-4
CH390
CSM1700
6 Pad LCC
1 Channel
10 pin Hybrid
2 Channel
16 pin Flat Pack
4 Channel
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 4 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Outline Drawings
16 pin DIP, 4 Channel
16 pin Flat Pack, 2 and 4 Channel
NOTE: DIMENSIONS IN MILLIMETERS
8 pin DIP 1 and 2 Channel
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 5 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
6 Terminal LCC Surface Mount, 1 Channel
1.651
2.286
6.223
5
4
3
6
1
2
0.635
1.27
2.54
4.318
CSM141A
R = .2286
1.67
0.762
0.635
4/5 Terminal Hybrid, 1 Channel
3.5
0.6
4.5
0.13
0.13
+0.2
+0.2
2.0
0.7
0.6
0.6
Device Marking
XXXXXXX
ISOCOM
XXXX
Isocom Part Number
Manufacturer
Date Code (XX year XX week)
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 6 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Hermetic Optocoupler Options
Option Description
10
Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is
available on commercial hi-rel product in 8 and 16 pin DIP
20
30
Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is
available on commercial and hi-rel product in 8 and 16 pin DIP.
60
Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is
available on commercial hi-rel product in 8 and 16 pin DIP
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 7 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Absolute Maximum Ratings
Storage Temperature
-65°C to +150°C
Operating Temperature
Lead Soldering Temperature
-55°C to +125°C
260C for 10S, 1.6mm below seating plane where appropriate
Input Diode
Peak Forward Current
Average Forward Current
Reverse Voltage
20mA
10mA
5V
1 mS duration, 500pps
(See note 3)
Power Dissipation
35mW
Output Detector
Supply Voltage
Current
-0.5 to 20V
40mA
VCC (See note 1)
IO
Collector Power Dissipation
Voltage
50mW
-0.5 to 20V
(See note 2)
VO (See note 1)
Single Channel Schematic
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 8 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Electrical Characteristics
TA = -55°C to +125°C U.O.S.
All typical values at VCC = 5V, TA = 25°C (each channel where appropriate).
Units
Parameter
Symbol Test Conditions
Device
Min Type
Max
High Level Output
IOH
IF = 2µA,
-
0.001 250
µA
Current (See notes 4 & 6) IOHX
VO = VCC = 5.5V
Lower Level Output VOL
IF = 0.5mA, IOL= 1.5mA, VCC = 4.5V
IF = 5mA, IOL= 10mA, VCC = 4.5V
VCC = 18V, IF1 = IF2 = IF3 = IF4 = 0
VCC = 5.5, IF1 = IF2 = IF3 = IF4 = 0
-
-
-
0.1
0.15
0.1
0.4
0.4
40
60
4
V
Voltage (See note 4)
High Level Supply
Current
ICCH
µA
mA
CSM160/1
Low Level Supply Current ICCL
VCC
=
18V, IF1 = IF2 = IF3 = IF4
=
-
-
1.4
-
1.6mA
(See note 4)
VCC = 5.5V, IF1 = IF2 = IF3 = IF4 = 2mA CSM160/1
RH = 45%, TA = 25°C, t = 5S
VIO = 1500Vdc
8
1.0
Input-Output Insulation
Leakage Current
II-O
µA
(See notes 7 & 13)
Input Forward Voltage
(See note 4)
Input Reverse Breakdown BVR
Voltage (See note 4)
VF
IF = 1.6mA, TA = 25°C
IF = 4.0mA
IR = 10µA, TA = 25°C
-
1.45
1.9
-
V
CSM160/1
5
-
-
V
Propagation Delay Time tPLH
to Logic High Output
RL = 4.7KΩ, VCC = 5V, IF = 0.5mA,
TA = 25°C
6N140
CS5700
8
60
µS
CSM6730
CH370/390
CD750
CSM1700
CSM160/1
6N140
100
20
30
(See note 4)
RL = 680Ω, VCC = 5V, IF = 5mA,
TA = 25°C
-
-
8
CS5700
CSM6730
CH370/390
CD750
60
CSM1700
Propagation Delay Time tPHL
to Logic Low Output
RL = 4.7KΩ, VCC = 5V, IF = 0.5mA, CH370/390
35
100
100
µS
TA = 25°C
CD750
CSM1700
CSM160
CSM161
CS5700
CSM6730
CH370/390
CD750
CSM1700
CS5700
(See note 4)
RL = 680Ω, VCC = 5V, IF = 5mA,
TA = 25°C
-
3
12
10
CSM6730
CSM160/1
5
-
-
Current Transfer Ratio
(See notes 4 & 5)
CTR
IF = 0.5mA, VO = 0.4V, VCC = 4.5V
IF = 1.6mA, VO = 0.4V, VCC = 4.5V
IF = 5mA, VO = 0.4V, VCC = 4.5V
300 700
200 1000
200 600
%
-
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 9 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Electrical Characteristics (Continued)
Common Mode Transient CMH
Immunity at Logical High
Output Level
VCC = 5V, TA = 25°C, VCM = 50V p-p
RL = 1.5KΩ, IF = 0Ma
RL = 2.2KΩ, IF = 0mA
500 1000
-
-
V/µS
V/µS
CH370/390
CS700
CSM1700
CSM6730
(See notes 4, 10 & 12)
Common Mode Transient CML
Immunity at Logical Low
Output Level
VCC = 5V, TA = 25°C, VCM = 50V p-p
RL = 1.5KΩ, IF = 1.6mA
RL = 2.2KΩ, IF = 1.6mA
500 -1000
CH370/390
CS700
(See notes 4, 10 & 12)
CSM1700
CSM6730
Typical Characteristics
TA = 25°C
Parameter
Symbol Test Conditions
Notes Min
Type
1012
1.5
60
-1.8
Max
Units
Ω
pF
pF
mV/°
C
Resistance
Capacitance
RIO
CIO
CIN
VF
TA
II-I
V10 = 500Vdc
f = 1MHz
f = 1MHz, VF = 0
IF = 1.6mA
4 & 8
4 & 8
4
-
-
-
-
-
-
-
-
Input Capacitance
Temperature Coefficient
of Forward Voltage
Input-Input Insulation
Leakage Current
Resistance
1
45% Relative Humidity
VII = 500Vdc, t = 5S
VII = 500Vdc
9
-
0.6
-
nA
RI-I
CI-I
9
9
-
-
1012
1
-
-
Ω
pF
Capacitance
f = 1MHz
Notes:
1. The ground pin should be the most negative voltage at the detector side. Keeping VCC as low as possible, but
greater than 2.0V, will provide lowest total IOH over temperature.
2. Output power is collector output plus one fourth of total supply power. Derate at 1.66mW/°C above 110°C.
3. Derate IF at 0.33mA/°C above 110°C.
4. Each channel.
5. Current Transfer Ratio is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times
100%.
6. IOHX is the leakage current resulting from channel to channel optical crosstalk. IF = 2µA for channel under test. For all
other channels, IF = 10mA.
7. Input pins are shorted together, and output pins are shorted together.
8. Measured between the LED anode and cathode shorted together and pins at output shorted together.
9. Measured between adjacent input pairs shorted together.
10. CMH is the maximum tolerable common mode transient to assure that the output will remain in a high logic state
(i.e., VO > 2.0V).
11. CML is the maximum tolerable common mode transient to assure that the output will remain in the logic low state
(i.e., VO< 0.8V).
12. In applications where dV/dt may exceed 50,000V/µS (such as a static discharge), a series resistor, RCC, should be
included to protect the detector IC’s from destructively high surge currents. The recommended value is
RCC
=
1V
kΩ
0.6IF(mA)
13. This is a momentary withstand test, not an operating condition.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 10 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Electrical Characteristics
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 11 of 12
QC 88000-C003: 2013
®
ISOCOM LTD
Switching Time Characteristics
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 12 of 12
QC 88000-C003: 2013
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明