LDC-35DA [MEANWELL]
35W Constant Power MODE Linear LED Driver;
| 型号： | LDC-35DA |
| 厂家： | 
MEAN WELL ENTERPRISES CO., LTD. |
| 描述： | 35W Constant Power MODE Linear LED Driver |
| 文件： | 总9页 (文件大小：113K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
35W Constant Power MODE Linear LED Driver
LDC-35 series
110
M
M
05
SELV
(for DA-Type only)
■ Features
■ Applications
ꢀConstant Power mode output
ꢀMetal housing design
ꢀLED panel lighting
ꢀIndoor LED lighting
ꢀLinear LED lighting
ꢀFull Power at 70~100% max Current
ꢀBuilt-in active PFC function
ꢀFlicker Free design
ꢀNo load / Standby power consumption <0.5W
ꢀOutput current level pre-settable
ꢀFunction options: 3 in 1 dimming (dim-to-off); DALI
interface, push dimming
ꢀTypical lifetime>50000 hours
ꢀSELV and Isolated
ꢀClass 2 power supply
ꢀ5 years warranty
■ Description
LDC-35 series is a 35W AC/DC LED driver featuring the constant power mode output.LDC-35
operates from 180~295VAC and output current can be adjust between 300mA to 1000mA.
Thanks to the efficiency up to 88%, with the fanless design, the entire series is able to
operate for -25℃~+80℃ case temperature under free air convection.LDC-35 is equipped with
various function options, such as dimming methodologies, so as to provide the optimal design
flexibility for LED lighting system.
■ Model Encoding
LDC -
35
Function options
Rated output wattage
Series name
Type
Blank
B
Function
Note
Non dimming
In Stock
In Stock
In Stock
3 in 1 dimming function (0~10Vdc and10V PWM signal and resistance )
DALI,push dimming
DA
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
SPECIFICATION
MODEL
LDC-35
OUTPUT CURRENT REGION 300 ~ 1000mA(300mA default)
RATED POWER Note.2 35W
CONSTANT CURRENT REGION Note.2 27 ~ 56V
FULL POWER CURRENT RANGE
OPEN CIRCUIT VOLTAGE(max.)
625 ~ 1000mA
60V
OUTPUT
LOW FREQUENCY
CURRENT RIPPLE
3.0% max. @rated current
CURRENT TOLERANCE
SET UP TIME Note.4
5.0%
500ms/230VAC
180 ~ 295VAC
VOLTAGE RANGE Note.3
FREQUENCY RANGE
POWER FACTOR (Typ.)
(Please refer to "STATIC CHARACTERISTIC" section)
47 ~ 63Hz
PF≧0.95/230VAC@load≧50%; PF≧0.92/277VAC@load≧75%
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
THD< 10%(@load≧50%/230VAC; @load≧75%/277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
TOTAL HARMONIC DISTORTION
INPUT
EFFICIENCY (Typ.)
88%(230VAC@Full load)
AC CURRENT (Typ.)
INRUSH CURRENT(Typ.)
0.2A / 230VAC 0.16A / 277VAC
COLD START 30A(twidth=250μs measured at 50% Ipeak)/230VAC; Per NEMA 410
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
17 units (circuit breaker of type B) / 29 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
SHORT CIRCUIT
<0.75mA / 277VAC
Hiccup mode or constant current limiting ,recovers automatically after fault condition is removed
61 ~ 80V
PROTECTION
FUNCTION
OVER VOLTAGE
Shut down o/p voltage with auto-recovery or re-power on to recovery
OVER TEMPERATURE
Shut down o/p voltage, with auto-recovery
Please refer to“DIMMING OPERATION”section
DIMMING
By external NTC, please refer to“TEMPERATURE COMPENSATION OPERATION”section
TEMP. COMPENSATION
WORKING TEMP.
MAX. CASE TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
Tcase=-25 ~ +80℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
Tcase=+80℃
20 ~ 95% RH non-condensing
ENVIRONMENT
-40 ~ +80℃, 10 ~ 95% RH
0.03%/℃ (0 ~ 60℃)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13, AS/NZS 61347.1:2016, AS/NZS IEC 61347.2.13:2013;
EN62384; GB19510.14,GB19510.1, EAC TP TC 004 approved
SAFETY STANDARDS Note.5
Compliance to IEC62386-101.102.207 for DA-Type only
I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
DALI STANDARDS
SAFETY &
EMC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION Note.5
EMC IMMUNITY
MTBF
Compliance to
EN55015,EN61000-3-2 Class C (@load≧50%) ; EN61000-3-3;GB/T17743,GB17625.1,EAC TP TC 020
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge immunity:Line-Earth:2KV,Line-Line:1KV) criteria A,EAC TP TC 020
1097K hrs min. Telcordia SR-332 (Bellcore)
280*30*21mm (L*W*H)
286Khrs min. MIL-HDBK-217F (25℃)
DIMENSION
OTHERS
NOTE
0.22Kg; 54pcs/12.88Kg/0.91CUFT
PACKING
1.All parameters NOT specially mentioned are measured at 230VAC input, rated currentand 25 ℃of ambient temperature.
2.Please refer to " OUTPUT CURRENT SETTING".
3.De r-ating may be needed under low input voltages.Please refer to STATIC CHARACTERISTIC sections for detail.s
4.Length of set up time is measured at first cold start.Turning ON/OFF the power supply may lead to increase of the set up time.
5.The driver is considered as a component that will be operated in combination with final equipment.Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6.This series meets the typical life expectancy of >50000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70 ℃or less.
7.Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
8.The ambient temperature derating of 35. ℃/1000m with fanless models and of 5 ℃/1000m with fan models for operating altitude higher than 2000m(6500ft)
.
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
BLOCK DIAGRAM
PFC fosc : 50~400KHz
PWM fosc : 30~200KHz
RECTIFIERS
&
FILTER
EMI FILTER
&
RECTIFIERS
POWER
SWITCHING
+V
I/P
-V
DIM+
DIM-
CP.
(B Type)
DETECTION
CIRCUIT
O.T.P.
O.L.P.
PWM & PFC
CONTROL
O.V.P.
CASE GROUND
OUTPUT CURRENT SETTING
◎I-V Operating Area.
Output rated current level can be adjusted by a additive resistance.
LDC-35
60V
56V
50V
40V
LDC-35
30V
27V
20V
10V
0V
100mA
300mA
500mA
700mA
900mA
1100mA
CURRENT
◎ Rated current setting table
Vo+
Vo+
Vo-
Vo-
NTC
NTC
IADJ
IADJ
DIM+
DIM-
15.2K
1A
19K
24.5K
0.8A
32.5K
0.7A
43K
46K
72.5K
0.5A
100K
150K
0.4A
300K
NC
TB2
0.9A
0.62A
0.6A
0.45A
0.35A
0.3A
resistor
Note: output power≤35W
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
DIMMING OPERATION
Vo+
Vo+
Vo-
Vo-
AC/L
AC/N
NTC
NTC
IADJ
IADJ
DIM+
DIM-
FG
DA-;N
DA+;Ls
※ 3 in 1 dimming function(for B-Type)
ꢀOutput constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal or resistance.
ꢀDirect connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
ꢀDimming source current from power supply: 100μA (typ.)
◎ Applying additive 0 ~ 10VDC
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0%
+
+
Vo+
-
-
Vo-
DIM+
+
Additive Voltage
-
DIM-
“DO NOT connect "DIM- to Vo-"
0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0%
◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
+
+
Vo+
-
-
Vo-
DIM+
Additive PWM signal
DIM-
“DO NOT connect "DIM- to Vo-"
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Duty cycle of additive 10V PWM signal dimming input
100%
◎ Applying additive resistance:
90%
80%
70%
60%
50%
40%
30%
20%
10%
0%
+
+
Vo+
-
-
Vo-
DIM+
Additive Resistance
DIM-
“DO NOT connect "DIM- to Vo-"
Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
3. To ensure the dimming performance at low dimming level,output current must be over 45mA.
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
※DALI interface
Vo+
Vo+
Vo-
Vo-
NTC
NTC
IADJ
IADJ
DIM+
DIM-
AC/L
AC/N
FG
AC/N
Push Button
AC/L
DA-;N
DA+;Ls
◎ PUSH dimming(primary side)
Action Action duration
Function
Short push 0.1~1 sec.
Long push 1.5~10 sec.
Turn ON-OFF the driver
Every Long Push changes the dimming direction, dimming up or down
Set up the dimming level to 100%
Reset
>11 sec.
ꢀThe factory default dimming level is at 100%.
ꢀIf the push action lasts less than 0.05 sec., it will not lead to a change for the status of the driver.
ꢀUp to 10 drivers can perform the PUSH dimming at the same time when utilizing one common push button.
ꢀThe maximum length of the cable from the push button to the last driver is 20 meters.
ꢀThe additive push button can be connected only between the LS terminal, as displayed in the diagram,
and AC/L (in brown or black); it will lead to short circuit if it is connected to AC/N.
◎ DALI interface(primary side)
ꢀApply DALI signal between DA+ and DA-
ꢀDALI protocol comprises 16 groups and 64 addresses.
ꢀFirst step is fixed at 8% of rated output power.
NOTE: DALI, Push dimming can not be used in the same time!(The factory setting defaults to DA)
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
TEMPERATURE COMPENSATION OPERATION
LDC-35 have the built-in temperature compensation function ; by connecting a temperature sensor (NTC resistor) between the +NTC / -NTC
terminal of LDC-35 and the detecting point on the lighting system or the surrounding environment, output current of LDC-35 could be
correspondingly changed, based on the sensed temperature, to ensure the long life of LED.
Vo+
Vo+
Vo-
Vo-
NTC
NTC
IADJ
IADJ
NTC resistor
DIM+
DIM-
◎ LDC-35 can still be operated normally when the NTC resistor is not connected and the value of output current will be the current level selected
through the IADJ. pin
NTC reference:
NTC resistance
<20K
◎
Output Current
Output current reduce as the resistance decreases
Normal output current
>20K
Notes: 1. MEAN WELL does not offer the NTC resistor and all the data above are measured by using resistor.
2. If new brand of NTC resistor is applied,please check the temperature curve first.
◎ Dimming function of the driver will be invalid when the "temperature compensation" function is in use.
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
OUTPUT LOAD vs TEMPERATURE
100
80
100
80
60
60
40
50
40
20
20
(HORIZONTAL)
(HORIZONTAL)
80
-25 -10
0
15
30
50
60
70
-25
-10
0
20
45
55
65
75
AMBIENT TEMPERATURE,Ta (℃)
Tcase (℃)
POWER FACTOR (PF) CHARACTERISTIC
STATIC CHARACTERISTIC
※ Tcase at 75℃
1
100
90
80
70
60
50
40
0.98
0.96
0.94
0.92
0.9
277V
230V
0.88
50%
60%
70%
80%
90%
100%
(35W)
180
190
200
210
230
240
295
220
LOAD
(230Vac Input)
INPUT VOLTAGE (V) 60Hz
EFFICIENCY vs LOAD
TOTAL HARMONIC DISTORTION (THD)
LDC-35 series possess superior working efficiency up to 90%.
※ 1000mA Model, Tcase at 75℃
※ 1000mA Model, Tcase at 75℃
10
92
9
8
7
6
5
4
3
2
90
88
86
84
82
80
78
76
277V
230V
277V
230V
50%
60%
70%
80%
90%
100%
50%
60%
70%
80%
90%
100%
LOAD
LOAD
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
LIFE TIME
120
100
80
60
40
20
0
20
30
40
50
60
70
80
Tcase (
)
℃
File Name:LDC-35-SPEC 2018-05-10
35W Constant Power MODE Linear LED Driver
LDC-35 series
MECHANICAL SPECIFICATION
CASE NO.: 263A Unit:mm
280
273
3.5
145
1
2
3
4
1
6
tc
2
3
4
5
6
7
5
6
TB2
TB1
7
8
ψ4.5
ψ4.5
9
10
tc
ꢀ
: Max. Case Temperature
Terminal Pin No. Assignment (TB1) :
Terminal Pin No. Assignment (TB2) :
PUSH DIMMING
Device connection
Retractive push-to-make
switch
Pin No.
Assignment
Pin No.
Assignment
1
2
3
4
5
6
7
ACL
1
2
Vo+
ACN
NC
Vo+
ACN
ACL
N
3
Vo-
FG
4
Vo-
LS
NC(for DA-type only )
DA-/N(for DA-type only)
DA+/Ls(for DA-type only)
5
NTC
NTC
6
7
IADJ
8
IADJ
9
DIM+(for B-type only)
DIM-(for B-type only)
10
TB1 wiring:
8-9mm
TB2 wiring:
8-9mm
0.5-0.75mm2
0.2-0.5mm2
Installation Manual
Please refer to : http://www.meanwell.com/manual.html
File Name:LDC-35-SPEC 2018-05-10
相关型号：
©2020 ICPDF网 联系我们和版权申明