DSC400-1111Q0081KI1T [MICREL]
Crystal-less⢠Configurable Clock Generator;型号: | DSC400-1111Q0081KI1T |
厂家: | MICREL SEMICONDUCTOR |
描述: | Crystal-less⢠Configurable Clock Generator |
文件: | 总10页 (文件大小:1007K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DSC400-1111Q0081
Crystal-less™ Configurable Clock Generator
General Description
Features
The DSC400-1111Q0081 is
a
four output
• Frequencies and output formats:
- 27MHz LVCMOS x 1
- 50MHz LVCMOS x 1
- 25MHz LVCMOS x 1
- 12MHz LVCMOS x 1
• Low RMS phase jitter: <1ps (typ)
• High stability: ±50ppm, ±25ppm
• Wide temperature range
- Ext. commercial: -20°C to +70°C
- Industrial: -40°C to +85°C
crystal-less™ clock generator. It utilizes Micrel's
proven PureSilicon™ MEMS technology to provide
excellent jitter and stability while incorporating
additional device functionality.
The frequencies of the outputs can be identical or
independently derived from two shared PLLs. Each
output may be configured independently to support
LVCMOS, LVPECL, LVDS, or HCSL output
standards.
The DSC400-1111Q0081 provides two independent
select lines for choosing between two sets of pre-
configured frequencies per bank. It also has two OE
pins to allow for enabling and disabling outputs.
• High supply noise rejection: -50dBc
• Available pin-selectable frequency table
- 1 pin per bank for 2 frequency sets
• Excellent shock & vibration immunity
- Qualified to MIL-STD-883
Applications
• Communications and Networks
• Ethernet
- 1G, 10GBASE-T/KR/LR/SR, and FCoE
• High reliability
- 20x better MTF than quartz based devices
• Supply range of 2.25V to 3.6V
• AEC-Q100 automotive qualified
• 20-pin 5mm x 3.2mm QFN package
• Storage Area Networks
- SATA, SAS, Fibre Channel
• Passive Optical Networks
- EPON, 10G-EPON, GPON, 10G-GPON
• HD/SD/SDI Video & Surveillance
• Automotive
• Media and Video
• Embedded and Industrial
VDD1/VDD2
Block Diagram
Control Circuitry
CLK1
27MHz LVCMOS
Output
Control
And
MEMS
PLL
CLK4
12MHz LVCMOS
Dividers
OE1
FSB1
Control Circuitry
CLK3
25MHz LVCMOS
Output
Control
And
MEMS
PLL
CLK2
50MHz LVCMOS
Dividers
OE2
FSB2
VSS
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 31, 2016
3754
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Ordering Information
Ordering Part Number
DSC400-1111Q0081KE1
DSC400-1111Q0081KE1T
DSC400-1111Q0081KE2
DSC400-1111Q0081KE2T
DSC400-1111Q0081KI1
DSC400-1111Q0081KI1T
DSC400-1111Q0081KI2
DSC400-1111Q0081KI2T
Temperature Range
-20°C to +70°C
-20°C to +70°C
-20°C to +70°C
-20°C to +70°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
High Stability
±50ppm
±50ppm
±25ppm
±25ppm
±50ppm
±50ppm
±25ppm
±25ppm
Shipping
Tube
Package
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
20-pin 5mm x 3.2mm QFN
Tape and Reel
Tube
Tape and Reel
Tube
Tape and Reel
Tube
Tape and Reel
Devices are Green and RoHS compliant. Sample material may have only a partial top mark.
Pin Configuration
OE1
VSS
NC
VSS
NC
VSS
VSS
OE2
20-pin 5mm x 3.2mm QFN
March 31, 2016
3754
2
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Pin Description
Pin Number
Pin Name
Pin Type
Pin Function
Output enable for Bank 1 (CLK1 and CLK4); active high - see Table 1
Leave unconnected or connect to ground
Ground
1
2
3
4
5
6
7
8
9
OE1
NC
I
VSS
VSS
NC
PWR
PWR
Ground
Leave unconnected or connect to ground
LVCMOS output 1 = 27MHz
CLK1
NC
O
Leave unconnected or connect to ground
LVCMOS output 2 = 50MHz
CLK2
VDD2
O
PWR
Power supply for Bank 2 (CLK3 and CLK2)
Input for selecting pre-configured frequencies on Bank 2 (CLK3 and CLK2)
No connect if the function is not used.
10
FSB2
I
I
11
12
13
14
15
16
17
18
19
OE2
NC
Output enable for Bank 2 (CLK3 and CLK2); active high - see Table 1
Leave unconnected or connect to ground
Ground
VSS
VSS
NC
PWR
PWR
Ground
Leave unconnected or connect to ground
LVCMOS output 3 = 25MHz
CLK3
NC
O
Leave unconnected or connect to ground
LVCMOS output 4 = 12MHz
CLK4
VDD1
O
PWR
Power supply for Bank 1 (CLK1 and CLK4)
Input for selecting pre-configured frequencies on Bank 1 (CLK1 and CLK4)
No connect if the function is not used.
20
FSB1
I
March 31, 2016
3754
3
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Operational Description
The DSC400-1111Q0081 is a crystal-less™ clock generator. Unlike older clock generators in the industry, it does not require an
external crystal to operate; it relies on integrated MEMS resonators that interface with internal PLLs. This technology enhances
performance and reliability by allowing tighter frequency stability over a far wider temperature range. In addition, the higher
resistance to shock and vibration decreases the aging rate, greatly improving product life in the system.
Inputs
There are 4 input signals in the device. Each has an internal (40kOhms) pull up, which defaults the selection to a high (1). Inputs
can be controlled through hardware strapping method with a resistor to ground to assert the input low (0). Inputs may also be
controlled by other components' GPIOs. In case more than one frequency set is desired, FSB1 and FSB2 are used for independent-
ly selecting one of two sets frequency per bank. FSB1 selects the pre-configured frequency set on Bank 1 (CLK1 and CLK4) and
FSB2 selects the pre-configured frequency set on Bank 2 (CLK3 and CLK2). If there is a requirement to disable outputs, the
inputs OE1 and OE2 are used to disable the banks of outputs. Outputs are disabled in tristate (Hi-Z) mode, see Table 1 below.
OE1
OE2
Bank 1 (CLK1 and CLK4)
Bank 2 (CLK3 and CLK2)
0
0
1
1
0
1
0
1
Hi-Z
Hi-Z
Hi-Z
Running
Hi-Z
Running
Running
Running
Table 1. Output Enable (OE) Selection Table
Outputs
The four outputs are grouped into two banks. Each bank is supplied by an independent VDD to allow for optimized noise
isolation between the two banks. Each bank provides two synchronous outputs generated by a common PLL:
• Bank 1 is composed of outputs CLK1 and CLK4
• Bank 2 is composed of outputs CLK3 and CLK2
Each output maybe pre-configured independently to be one of the following formats: LVCMOS, LVDS, LVPECL or HCSL.
In case the output is configured to be single ended (LVCMOS only), the frequency is generated on the true output (CLKx+) and
the complement output (CLKx-) is shut off in a low state. Frequencies can be chosen from 2.3MHz to 460MHz for differential
outputs and from 2.3MHz to 170MHz on LVCMOS outputs.
Output Clock Frequencies
Output
CLK1
CLK2
CLK3
CLK4
Frequency (MHz)
27
50
25
12
Power
VDD1 and VDD2 supply the power to banks 1 and 2 respectively. Each VDD may have different supply voltage from the other
as long as it is within the 2.25V to 3.6V range. Each VDD pin should have a 0.1µF capacitor to filter high frequency noise.
VSS is common to the entire device. The exposed die paddle should be connected to VSS.
March 31, 2016
3754
4
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Absolute Maximum Ratings
Item
Min.
-0.3
-0.3
-
Max.
+4.0
Units
V
Condition
Supply Voltage
Input Voltage
Junction Temp
Storage Temp
Soldering Temp
VDD + 0.3
+150
V
°C
°C
°C
-55
-
+150
+260
40sec max.
ESD
HBM
MM
4000
400
-
V
CDM
1500
1000+ years of data retension on internal memory
Specifications (Unless specified otherwise: Ta = 25°C, VDD = 3.3V)
Parameter
Symbol
Condition
Min.
Typ.
Max.
Unit
Supply Voltage¹
VDD
2.25
3.6
V
OE (1:2) = 0
All outputs are disabled
Supply Current - Core²
Frequency Stability
IDDcore
F
40
44
mA
±50
±25
All temp and VDD ranges
ppm
Aging - first year
Aging - after first year
Startup Time³
Fy1
Fy2+
tSU
1 year @ 25°C
±5
< ±1/yr
5
ppm
ppm
ms
Year 2 and beyond @ 25°C
T = 25°C
Input Logic Levels
Input Logic High
Input Logic Low
VIH
VIL
0.75 x VDD
-
-
V
0.25 x VDD
4
Output Disable Time
tDA
tEN
Rpu
OE(1:2) transition from 1 to 0
OE(1:2) transition from 0 to 1
All input pins have an internal pull-up
5
ns
ns
4
Output Enable Time
20
Pull-Up Resistor
40
kOhms
Notes:
1. VDD pins should be filtered with 0.1µF capacitor connected between VDD and VSS.
2. The addition of IDDcore and IDDio provides total current consumption of the device.
3. tSU is time to 100ppm stable output frequency after VDD is applied and outputs are enabled.
4. Output Waveform figures below the parameters. See Output Waveform section.
March 31, 2016
3754
5
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
LVCMOS Outputs
Output Logic Levels
Output Logic High
Output Logic Low
VOH
VOL
I = ±6mA
0.9 x VDD
-
V
-
0.1 x VDD
Output Transition Time³
Rise Time
20% to 80%
CL = 15pF
tR
tF
1.1
1.3
2
2
ns
Fall Time
f1
f2
f3
f4
CLK1
CLK2
CLK3
CLK4
27
50
25
12
Frequency
MHz
Output Duty Cycle
Supply Current - IO²
Period Jitter
SYM
Differential
45
55
14
%
IDDio Per output at 125MHz, CL = 15pF
11
3
mA
JPER
CLK(1:4) = 125MHz
psRMS
200kHz to 20MHz @ 156.25MHz
100kHz to 20MHz @ 156.25MHz
12kHz to 20MHz @ 156.25MHz
0.3
0.38
1.7
Integrated Phase Noise
JPH
psRMS
2
LVCMOS Typical Termination Scheme
S
R is a series resistor implemented to match the trace impedance to that of the clock output. Depending on the board layout,
the value may range from 0 to 27Ohms.
LVCMOS Output Waveform
March 31, 2016
3754
6
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Connection Diagram
The connection Diagram below includes recommended capacitors to be placed on each VDD for noise filtering.
March 31, 2016
3754
7
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Solder Reflow Profile
MSL 1 @ 260°C refer to JSTD-020C
Ramp-Up Rate (200°C to Peak Temp)
Preheat Time 150°C to 200°C
Time maintained above 217°C
Peak Temperature
3°C/sec Max.
60 - 180 sec
60 - 150 sec
255 - 260°C
20 - 40 sec
Time within 5°C of actual Peak
Ramp-Down Rate
6°C/sec Max.
8 min Max.
Time 25°C to Peak Temperature
March 31, 2016
3754
8
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Package Information
20 QFN, 5.0mm x 3.2mm Package
March 31, 2016
3754
9
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
Micrel, Inc.
DSC400-1111Q0081
Recommended Solder Pad layout
Connect the center pad to ground plane for best thermal performance.
units: mm[inches]
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data
sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right
to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and
conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty
relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose,
merchantability, or infringement of any patent, copyright or other intellectual property right.
Micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction
of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a)
are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected
to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices
or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale.
© 2016 Micrel, Incorporated.
March 31, 2016
3754
10
Revision 1.0
tcghelp@micrel.comor (408) 955-1690
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明