AT25HP512C1-10CJ-2.7 [MICROCHIP]
EEPROM, 64KX8, Serial;型号: | AT25HP512C1-10CJ-2.7 |
厂家: | MICROCHIP |
描述: | EEPROM, 64KX8, Serial 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 时钟 内存集成电路 |
文件: | 总21页 (文件大小:415K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
• 128-byte Page Mode Only for Write Operations
• Low-voltage and Standard-voltage Operation
– 2.7 (VCC = 2.7V to 5.5V)
– 1.8 (VCC = 1.8V to 5.5V)
• 10 MHz (5V), 5MHz (2.7V) and 2 MHz (1.8V) Clock Rate
• Block Write Protection
• Protect 1/4, 1/2, or Entire Array
• Write Protect (WP) Pin and Write Disable Instructions for
both Hardware and Software Data Protection
• High Reliability
– Endurance: 100K Write Cycles
– Data Retention: >40 Years
• 8-lead PDIP, 8-lead EIAJ SOIC, 16-lead JEDEC SOIC, 8-lead Leadless Array Package,
and 8-lead SOIC Array Package (SAP)
• Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers
SPI Serial
EEPROMs
256K (32,768 x 8)
512K (65,536 x 8)
Description
AT25HP256(1)
AT25HP512
The AT25HP256/512 provides 262,144/524,288 bits of serial electrically erasable pro-
grammable read only memory (EEPROM) organized as 32,768/65,536 words of 8-bits
each. The device is optimized for use in many industrial and commercial applications
where high-speed, low-power, and low-voltage operation are essential. The
AT25HP256/512 is available in a space saving 8-lead PDIP (AT25HP256/512), 8-lead
EIAJ SOIC (AT25HP256), 16-lead JEDEC SOIC (AT25HP512), 8-lead Leadless Array
(AT25HP256/512) package, and 8-lead SOIC Array package (SAP). In addition, the
entire family is available in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) versions.
Note:
1. Not recommended for
new design; please refer to
AT25256A datasheet.
Table 1. Pin Configurations
16-lead SOIC
Pin Name
CS
Function
CS
SO
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VCC
HOLD
NC
Chip Select
NC
SCK
SI
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
NC
NC
NC
NC
NC
NC
WP
GND
SCK
SI
SO
GND
VCC
WP
Power Supply
Write Protect
8-lead Leadless Array
8
7
6
5
1
2
3
4
VCC
HOLD
SCK
CS
SO
HOLD
Suspends Serial Input
WP
GND
SI
Bottom View
8-lead SOIC Array Package
(SAP)
8-lead SOIC
8-lead PDIP
1
8
7
VCC
CS
SO
1
2
8
7
VCC
CS
SO
8
7
6
5
1
2
3
4
VCC
HOLD
SCK
CS
2
HOLD
SCK
SI
HOLD
SCK
SI
SO
3
4
6
5
3
4
6
5
WP
WP
WP
GND
GND
GND
SI
Rev. 1113L–SEEPR–3/06
Bottom View
The AT25HP256/512 is enabled through the Chip Select pin (CS) and accessed via a 3-
wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and Serial
Clock (SCK). All programming cycles are completely self-timed, and no separate erase
cycle is required before write.
Block Write protection is enabled by programming the status register with top ¼, top ½
or entire array of write protection. Separate Program Enable and Program Disable
instructions are provided for additional data protection. Hardware data protection is pro-
vided via the WP pin to protect against inadvertent write attempts to the status register.
The HOLD pin may be used to suspend any serial communication without resetting the
serial sequence.
Absolute Maximum Ratings*
*NOTICE:
Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions beyond those indicated in the operational sec-
tions of this specification is not implied. Exposure to
absolute maximum rating conditions for extended
periods may affect device reliability.
Operating Temperature..................................–55°C to +125°C
Storage Temperature.....................................–65°C to +150°C
Voltage on Any Pin
with Respect to Ground....................................–1.0V to +7.0V
Maximum Operating Voltage .......................................... 6.25V
DC Output Current........................................................ 5.0 mA
Figure 1. Block Diagram
32,768/65,536x8
2
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
Table 2. Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +5.0V (unless otherwise noted)
Symbol
COUT
CIN
Test Conditions
Max
8
Units
pF
Conditions
VOUT = 0V
VIN = 0V
Output Capacitance (SO)
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
Note:
1. This parameter is characterized and is not 100% tested.
Table 3. DC Characteristics
Applicable over recommended operating range from: TAI = –40°C to +85°C, VCC = +1.8V to +5.5V,
AC = 0°C to +70°C, VCC = +1.8V to +5.5V (unless otherwise noted)
T
Symbol
VCC1
VCC2
VCC3
ICC1
ICC2
ISB1
Parameter
Test Condition
Min
1.8
2.7
4.5
Typ
Max
3.6
Units
V
Supply Voltage
Supply Voltage
5.5
V
Supply Voltage
5.5
V
Supply Current
VCC = 5.0V at 5 MHz, SO = Open Read
VCC = 5.0V at 5 MHz, SO = Open Write
VCC = 1.8V, CS = VCC
6.0
4.0
0.1
0.2
2.0
10.0
7.0
mA
mA
µA
µA
µA
µA
µA
V
Supply Current
Standby Current
Standby Current
Standby Current
Input Leakage
2.0
ISB2
VCC = 2.7V, CS = VCC
2.0
ISB3
VCC = 5.0V, CS = VCC
5.0
IIL
VIN = 0V to VCC
–3.0
–3.0
3.0
IOL
Output Leakage
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Output Low Voltage
Output High Voltage
VIN = 0V to VCC, TAC = 0°C to 70°C
3.0
(1)
VIL
–0.6
VCC x 0.3
VCC + 0.5
0.4
(1)
VIH
VCC x 0.7
V
VOL1
VOH1
VOL2
VOH2
I
OL = 3.0 mA
IOH = –1.6 mA
OL = 0.15 mA
IOH = –100 µA
V
4.5V ≤ VCC ≤ 5.5V
1.8V ≤ VCC ≤ 3.6V
VCC – 0.8
VCC – 0.2
V
I
0.2
V
V
Note:
1. VIL and VIH max are reference only and are not tested.
3
1113L–SEEPR–3/06
Table 4. AC Characteristics
Applicable over recommended operating range from TA = –40°C to +85°C, VCC = As Specified,
CL = 1 TTL Gate and 30 pF (unless otherwise noted)
Symbol
Parameter
Voltage
Min
Max
Units
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
0
0
0
10
5
2
fSCK
SCK Clock Frequency
MHz
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
2
2
2
tRI
Input Rise Time
Input Fall Time
SCK High Time
SCK Low Time
CS High Time
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
2
2
2
tFI
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
40
80
200
tWH
tWL
tCS
tCSS
tCSH
tSU
tH
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
40
80
200
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
50
100
250
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
50
100
250
CS Setup Time
CS Hold Time
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
50
100
250
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
12
20
50
Data In Setup Time
Data In Hold Time
Hold Setup Time
Hold Hold Time
Output Valid
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
10
20
50
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
25
50
100
tHD
tCD
tV
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
25
50
100
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
0
0
0
40
80
200
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
0
0
0
tHO
Output Hold Time
Hold to Output Low Z
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
0
0
0
100
200
300
tLZ
4
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
Table 4. AC Characteristics (Continued)
Applicable over recommended operating range from TA = –40°C to +85°C, VCC = As Specified,
CL = 1 TTL Gate and 30 pF (unless otherwise noted)
Symbol
Parameter
Voltage
Min
Max
Units
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
100
200
300
tHZ
Hold to Output High Z
ns
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
100
100
250
tDIS
Output Disable Time
Write Cycle Time
ns
ms
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
10
10
10
tWC
4.5 – 5.5
2.7 – 5.5
1.8 – 5.5
Endurance(1)
5.0V, 25°C, Page Mode
100K
Write Cycles
Note:
1. This parameter is characterized and is not 100% tested.
5
1113L–SEEPR–3/06
Serial Interface
Description
MASTER: The device that generates the serial clock.
SLAVE: Because the serial clock pin (SCK) is always an input, the AT25HP256/512
always operates as a slave.
TRANSMITTER/RECEIVER: The AT25HP256/512 has separate pins designated for
data transmission (SO) and reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be
received. This byte contains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the
AT25HP256/512, and the serial output pin (SO) will remain in a high impedance state
until the falling edge of CS is detected again. This will reinitialize the serial
communication.
CHIP SELECT: The AT25HP256/512 is selected when the CS pin is low. When the
device is not selected, data will not be accepted via the SI pin, and the SO will remain in
a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS pin to select the
AT25HP256/512. When the device is selected and a serial sequence is underway,
HOLD can be used to pause the serial communication with the master device without
resetting the serial sequence. To pause, the HOLD pin must be brought low while the
SCK pin is low. To resume serial communication, the HOLD pin is brought high while the
SCK pin is low (SCK may still toggle during HOLD). Inputs to the SI pin will be ignored
while the SO pin is in the high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations
when held high. When the WP pin is brought low and WPEN bit is “1”, all write opera-
tions to the status register are inhibited. WP going low while CS is still low will interrupt a
write to the status register. If the internal write cycle has already been initiated, WP
going low will have no effect on any write operation to the status register. The WP pin
function is blocked when the WPEN bit in the status register is “0”. This will allow the
user to install the AT25HP256/512 in a system with the WP pin tied to ground and still
be able to write to the status register. All WP pin functions are enabled when the WPEN
bit is set to “1”.
6
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
SPI Serial Interface
Figure 2. Functional Description
AT25HP256/512
7
1113L–SEEPR–3/06
The AT25HP256/512 is designed to interface directly with the synchronous serial
peripheral interface (SPI) of the 6800 type series of microcontrollers.
The AT25HP256/512 utilizes an 8-bit instruction register. The list of instructions and
their operation codes are contained in Table 5. All instructions, addresses, and data are
transferred with the MSB first and start with a high-to-low CS transition.
Table 5. Instruction Set for the AT25HP256/512
Instruction Name
WREN
Instruction Format
0000 X110
Operation
Set Write Enable Latch
Reset Write Enable Latch
Read Status Register
Write Status Register
Read Data from Memory Array
Write Data to Memory Array
WRDI
0000 X100
RDSR
0000 X101
WRSR
0000 X001
READ
0000 X011
WRITE
0000 X010
WRITE ENABLE (WREN): The device will power up in the write disable state when VCC
is applied. All programming instructions must therefore be preceded by a Write Enable
instruction.
WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the Write
Disable instruction disables all programming modes. The WRDI instruction is indepen-
dent of the status of the WP pin.
READ STATUS REGISTER (RDSR): The Read Status Register instruction provides
access to the status register. The Ready/Busy and Write Enable status of the device
can be determined by the RDSR instruction. Similarly, the block write protection bits
indicate the extent of protection employed. These bits are set by using the WRSR
instruction.
Table 6. Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WPEN
X
X
X
BP1
BP0
WEN
RDY
8
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
Table 7. Read Status Register Bit Definition
Bit
Definition
Bit 0 = “0” (RDY) indicates the device is ready. Bit 0 = “1” indicates the write
cycle is in progress.
Bit 0 (RDY)
Bit 1= “0” indicates the device is not write-enabled. Bit 1 = “1” indicates the
device is write-enabled.
Bit 1 (WEN)
Bit 2 (BP0)
Bit 3 (BP1)
See Table 8.
See Table 8.
Bits 4-6 are “0”s when device is not in an internal write cycle.
Bit 7 (WPEN) See Table 9.
Bits 0-7 are “1”s during an internal write cycle.
WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select
one of four levels of protection. The AT25HP256/512 is divided into four array seg-
ments. Top quarter (1/4), top half (1/2), or all of the memory segments can be protected.
Any of the data within any selected segment will therefore be READ only. The block
write protection levels and corresponding status register control bits are shown in Table
8.
The three bits, BP0, BP1, and WPEN are nonvolatile cells that have the same properties
and functions as the regular memory cells (e.g., WREN, tWC, RDSR).
Table 8. Block Write Protect Bits
Status Register Bits
BP1 BP0
Array Addresses Protected
AT25HP256/512
Level
0
0
0
1
1
0
1
0
1
None
1(1/4)
2(1/2)
3(All)
6000 - 7FFF/C000 - FFFF
4000 - 7FFF/8000 - FFFF
0000 - 7FFF/0000 - FFFF
The WRSR instruction also allows the user to enable or disable the write protect (WP)
pin through the use of the write protect enable (WPEN) bit. Hardware write protection is
enabled when the WP pin is low and the WPEN bit is “1”. Hardware write protection is
disabled when either the WP pin is high or the WPEN bit is “0.” When the device is hard-
ware write protected, writes to the status register, including the block protect bits and the
WPEN bit, and the block-protected sections in the memory array are disabled. Writes
are only allowed to sections of the memory which are not block-protected.
NOTE: When the WPEN bit is hardware write protected, it cannot be changed back to
“0” as long as the WP pin is held low.
Table 9. WPEN Operation
WPEN
WP
X
WEN
ProtectedBlocks
Protected
UnprotectedBlocks
Protected
Status Register
Protected
0
0
1
0
1
0
X
Protected
Writable
Writable
Low
Protected
Protected
Protected
9
1113L–SEEPR–3/06
Table 9. WPEN Operation (Continued)
WPEN
WP
WEN
ProtectedBlocks
Protected
UnprotectedBlocks
Writable
Status Register
Protected
1
X
X
Low
High
High
1
0
1
Protected
Protected
Protected
Protected
Writable
Writable
READ SEQUENCE (READ): Reading the AT25HP256/512 via the SO pin requires the
following sequence. After the CS line is pulled low to select a device, the read op-code
is transmitted via the SI line followed by the byte address to be read (see Table 10).
Upon completion, any data on the SI line will be ignored. The data (D7–D0) at the spec-
ified address is then shifted out onto the SO line. If only one byte is to be read, the CS
line should be driven high after the data comes out. The read sequence can be contin-
ued since the byte address is automatically incremented and data will continue to be
shifted out. When the highest address is reached, the address counter will roll over to
the lowest address allowing the entire memory to be read in one continuous read cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25HP256/512, two separate
instructions must be executed. First, the device must be write enabled via the WREN
instruction. Then a Write instruction may be executed. Also, the address of the memory
location(s) to be programmed must be outside the protected address field location
selected by the block write protection level. During an internal write cycle, all commands
will be ignored except the RDSR instruction.
A Write instruction requires the following sequence. After the CS line is pulled low to
select the device, the Write op-code is transmitted via the SI line followed by the byte
address and the data (D7–D0) to be programmed (see Table 10). Programming will start
after the CS pin is brought high. The Low-to-High transition of the CS pin must occur
during the SCK low time immediately after clocking in the D0 (LSB) data bit.
The Ready/Busy status of the device can be determined by initiating a Read Status
Register (RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”,
the write cycle has ended. Only the RDSR instruction is enabled during the write pro-
gramming cycle.
The AT25HP256/512 is capable of a 128-byte page write operation. After each byte of
data is received, the seven low-order address bits are internally incremented by one; the
high-order bits of the address will remain constant. If more than 128 bytes of data are
transmitted, the address counter will roll over and the previously written data will be
overwritten. The AT25HP256/512 is automatically returned to the write disable state at
the completion of a write cycle.
NOTE: If the device is not write enabled (WREN), the device will ignore the Write
instruction and will return to the standby state, when CS is brought high. A new CS fall-
ing edge is required to reinitiate the serial communication.
Table 10. Address Key
Address
AN
AT25HP256/512
A14 – A0 / A15 – A0
A15 / none
Don’t Care Bits
NOTE: 128-byte Page Write operation only. Content of the page in the array will not be
guaranteed if less than 128 bytes of data is received (byte write is not supported).
10
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
Timing Diagrams (for SPI Mode 0 (0,0))
Figure 3. Synchronous Data Timing
t
CS
V
V
IH
CS
IL
t
t
CSH
CSS
V
IH
t
WL
t
WH
SKC
SI
V
IL
t
SU
t
H
V
V
IH
VALID IN
IL
t
V
t
t
HO
DIS
V
OH
HI-Z
HI- Z
SO
V
OL
Figure 4. WREN Timing
CS
SCK
SI
SO
Figure 5. WRDI Timing
CS
SCK
SI
WRDI OP-CODE
HI-Z
SO
11
1113L–SEEPR–3/06
Figure 6. RDSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14
15
SCK
SI
INSTRUCTION
DATA OUT
HIGH IMPEDANCE
7
6
5
4
3
2
1
0
SO
MSB
Figure 7. WRSR Timing
Figure 8. READ Timing
12
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
Figure 9. WRITE Timing (AT25HP256)
CS
0
1
2
3
4
5
6
7
8
9
10 11 20 21 22 23 24 25 26 27 28 29 30 31
SCK
SI
BYTE ADDRESS
...
1ST BYTE DATA IN
13
INSTRUCTION
1
0
15
14
7
6
5
3
2
2
4
0
3
1
HIGH IMPEDANCE
SO
Figure 10. PAGE WRITE Timing (AT25HP512)
CS
0
1
2
3
4
5
6
7
8
9
10 11 20 21 22 23 24 25 26 10431044 1045 1046 1047
SCK
SI
st
th
BYTE ADDRESS 1 BYTE DATA IN
128 BYTE DATA IN
INSTRUCTION
13
12
1
0
15
14
7
6
5
3
2
2
4
0
3
1
HIGH IMPEDANCE
SO
Figure 11. HOLD Timing
CS
tCD
tCD
SCK
HOLD
SO
tHD
tHD
tHZ
tLZ
13
1113L–SEEPR–3/06
AT25HP256 Ordering Information(1)
Ordering Code
Package
Operation Range
AT25HP256-10PU-2.7(2)
AT25HP256-10PU-1.8(2)
AT25HP256W-10SU-2.7(2)
AT25HP256W-10SU-1.8(2)
AT25HP256C1-10CU-2.7(2)
AT25HP256C1-10CU-1.8(2)
AT25HP256Y4-10YU-1.8(2)
8P3
8P3
8S2
Lead-free/Halogen-free/
Industrial Temperature
(–40°C to 85°C)
8S2
8CN1
8CN1
8Y4
AT25HP256-W2.7-11(3)
AT25HP256-W1.8-11(3)
Die Sale
Die Sale
Industrial Temperature
(–40°C to 85°C)
Notes: 1. This device is not recommended for new design. Please refer to AT25256A datasheet. For 2.7 devices used in 4.5V to 5.5V
range, please refer to performance values in the AC and DC characteristics table.
2. “U” designates Green Package & RoHS compliant.
3. Available in waffle pack and wafer form; order as SL719 for wafer form. Bumped die available upon request. Please contact
Serial EEPROM marketing.
Package Type
8CN1
8P3
8-lead, 0.300” Wide, Leadless Array Package (LAP)
8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP)
8-lead, 0.200" Wide, Plastic Small Outline Package (EIAJ)
8-lead, 6.00 mm x 4.90 mm Body, Dual Footprint, Non-leaded, Small Array Package (SAP)
Options
8S2
8Y4
–2.7
–1.8
Low Voltage (2.7V to 5.5V)
Low Voltage (1.8V to 5.5V)
14
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
AT25HP512 Ordering Information(1)
Ordering Code
Package
Operation Range
AT25HP512C1-10CI-2.7
AT25HP512-10PI-2.7
AT25HP512W2-10SI-2.7
8CN1
8P3
Industrial Temperature
(–40°C to 85°C)
16S2
AT25HP512C1-10CI-1.8
AT25HP512-10PI-1.8
AT25HP512W2-10SI-1.8
8CN1
8P3
Industrial Temperature
(–40°C to 85°C)
16S2
AT25HP512C1-10CU-2.7(2)
AT25HP512C1-10CU-1.8(2)
AT25HP512-10PU-2.7(2)
AT25HP512-10PU-1.8(2)
AT25HP512W2-10SU-2.7(2)
AT25HP512W2-10SU-1.8(2)
8CN1
8CN1
8P3
Lead-free/ Halogen-free
Industrial Temperature
(–40°C to 85°C)
8P3
16S2
16S2
AT25HP512-W2.7-11(3)
AT25HP512-W1.8-11(3)
Die Sale
Die Sale
Industrial Temperature
(–40°C to 85°C)
Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics tables.
2. “U” designates Green Package & RoHS compliant.
3. Available in waffle pack and wafer form; order as SL719 for wafer form. Bumped die available upon request. Contact Serial
EEPROM marketing.
Package Type
8CN1
8P3
8-lead, 0.300" Wide, Leadless Array Package (LAP)
8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP)
16-lead, 0.300" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)
Options
16S2
–2.7
–1.8
Low Voltage (2.7V to 5.5V)
Low Voltage (1.8V to 5.5V)
15
1113L–SEEPR–3/06
Packaging Information
8CN1 – LAP
Marked Pin1 Indentifier
E
A
D
A1
Top View
Side View
Pin1 Corner
L1
0.10 mm
TYP
8
7
1
e
COMMON DIMENSIONS
(Unit of Measure = mm)
2
3
MIN
0.94
0.30
0.36
7.90
4.90
MAX
1.14
0.38
0.46
8.10
5.10
NOM
1.04
NOTE
SYMBOL
A
6
5
A1
b
0.34
b
0.41
1
4
D
8.00
E
5.00
e1
L
e
1.27 BSC
0.60 REF
.0.67
e1
L
Bottom View
0.62
0.92
0.72
1.02
1
1
L1
0.97
Note: 1. Metal Pad Dimensions.
11/13/01
DRAWING NO.
REV.
A
TITLE
2325 Orchard Parkway
San Jose, CA 95131
8CN1, 8-lead (8 x 5 x 1.04 mm Body), Lead Pitch 1.27 mm,
8CN1
R
Leadless Array Package (LAP)
16
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
8P3 – PDIP
E
1
E1
N
Top View
c
eA
End View
COMMON DIMENSIONS
(Unit of Measure = inches)
D
e
MIN
–
MAX
0.210
0.195
0.022
0.070
0.045
0.014
0.400
–
NOM
–
NOTE
SYMBOL
D1
A2 A
A
2
A2
b
0.115
0.014
0.045
0.030
0.008
0.355
0.005
0.300
0.240
0.130
0.018
0.060
0.039
0.010
0.365
–
5
6
6
b2
b3
c
D
3
3
4
3
b2
L
D1
E
b3
4 PLCS
0.310
0.250
0.100 BSC
0.300 BSC
0.130
0.325
0.280
b
E1
e
Side View
eA
L
4
2
0.115
0.150
Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
01/09/02
TITLE
DRAWING NO.
REV.
2325 Orchard Parkway
San Jose, CA 95131
8P3, 8-lead, 0.300" Wide Body, Plastic Dual
In-line Package (PDIP)
8P3
B
R
17
1113L–SEEPR–3/06
16S2 – JEDEC SOIC
1
E
N
Top View
End View
COMMON DIMENSIONS
(Unit of Measure = inches)
MIN
MAX
0.1043
0.0118
0.0200
0.0125
0.4133
0.2992
0.4190
0.050
NOM
NOTE
SYMBOL
A
A1
b
0.0926
0.0040
0.0130
0.0091
0.3977
0.2914
0.3940
0.0160
–
–
–
–
–
–
–
–
5
C
D
E
H
L
Side View
2
3
4
e
0.050 BSC
Notes: 1. This drawing is for general information only; refer to JEDEC drawing MS-013, Variation AA, for additional information.
2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed
3. Dimension E does not include inter-lead Flash or protrusion. Inter-lead Flash and protrusions shall not exceed 0.25 mm
4.
5. The lead width B, as measured 0.36 mm (0.014") or greater above the seating plane, shall not exceed a maximum value of 0.61 mm
(0.024") per side.
1/9/02
REV.
A
16S2, 16-lead, 0.300" Wide Body, Plastic Gull
Wing Small Outline Package (SOIC)
16S2
18
AT25HP256/512
1113L–SEEPR–3/06
AT25HP256/512
8S2 – EIAJ SOIC
C
1
E
E1
L
N
Top View
∅
End View
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
MIN
1.70
0.05
0.35
0.15
5.13
5.18
7.70
0.51
0°
MAX
2.16
0.25
0.48
0.35
5.35
5.40
8.26
0.85
8°
NOM
NOTE
SYMBOL
A1
A
A1
b
5
5
C
D
E1
E
D
2, 3
Side View
L
∅
e
1.27 BSC
4
Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information.
2. Mismatch of the upper and lower dies and resin burrs are not included.
3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded.
4. Determines the true geometric position.
5. Values b and C apply to pb/Sn solder plated terminal. The standard thickness of the solder layer shall be 0.010 +0.010/−0.005 mm.
10/7/03
TITLE
REV.
DRAWING NO.
2325 Orchard Parkway
San Jose, CA 95131
8S2, 8-lead, 0.209" Body, Plastic Small
Outline Package (EIAJ)
8S2
C
R
19
1113L–SEEPR–3/06
8Y4 – SAP
PIN 1 INDEX AREA
A
PIN 1 ID
D
E1
L
A1
E
e
b
e1
A
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
–
MAX
0.90
0.05
6.20
5.10
3.15
3.15
0.45
NOM
–
NOTE
A
A1
D
0.00
5.80
4.70
2.85
2.85
0.35
–
6.00
E
4.90
D1
E1
b
3.00
3.00
0.40
e
1.27 TYP
3.81 REF
0.60
e1
L
0.50
0.70
5/24/04
DRAWING NO.
REV.
TITLE
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
8Y4, 8-lead (6.00 x 4.90 mm Body) SOIC Array Package
(SAP) Y4
8Y4
A
R
20
AT25HP256/512
1113L–SEEPR–3/06
Atmel Corporation
Atmel Operations
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Memory
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Regional Headquarters
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© Atmel Corporation 2006. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are® and others, are registered trade-
marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
1113L–SEEPR–3/06
相关型号:
©2020 ICPDF网 联系我们和版权申明