MCP125233X50I/MS [MICROCHIP]
Low-Noise, Positive-Regulated Charge Pump;![MCP125233X50I/MS](http://pdffile.icpdf.com/pdf2/p00324/img/icpdf/MCP1252-ADJE_1992235_icpdf.jpg)
型号: | MCP125233X50I/MS |
厂家: | ![]() |
描述: | Low-Noise, Positive-Regulated Charge Pump |
文件: | 总20页 (文件大小:562K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
MCP1252/3
Low-Noise, Positive-Regulated Charge Pump
Features:
Description:
• Inductorless, Buck/Boost, DC/DC Converter
• Low Power: 80 µA (Typical)
The MCP1252/3 are inductorless, positive-regulated
charge pump DC/DC converters. The devices generate
a regulated fixed (3.3V or 5.0V) or adjustable output
voltage. They are specifically designed for applications
requiring low noise and high efficiency and are able to
deliver up to 120 mA output current. The devices allow
the input voltage to be lower or higher than the output
voltage, by automatically switching between buck/
boost operation.
• High Output Voltage Accuracy:
- ±2.5% (VOUT Fixed)
• 120 mA Output Current
• Wide Operating Temperature Range:
- Industrial Temperature (I): -40°C to +85°C
- Extended Temperature (E): -40°C to +125°C
• Thermal Shutdown and Short-Circuit Protection
• Uses Small Ceramic Capacitors
• Switching Frequency:
The MCP1252 has a switching frequency of 650 kHz,
avoiding interference with sensitive IF bands. The
MCP1253 has a switching frequency of 1 MHz and
allows the use of smaller capacitors than the
MCP1252, thus saving board space and cost.
- MCP1252: 650 kHz
- MCP1253: 1 MHz
Both devices feature a power-good output that can be
used to detect out-of-regulation conditions. Extremely
low supply current and low external parts count (three
capacitors) make these devices ideal for small, battery-
powered applications. A shutdown mode is also pro-
vided for further power reduction. The MCP1252 and
MCP1253 feature thermal and short-circuit protection
and are offered in space-saving, 8-lead, MSOP
packages.
• Low-Power Shutdown Mode: 0.1 µA (Typical)
• Shutdown Input Compatible with 1.8V Logic
• VIN Range: 2.0V to 5.5V
• Selectable Output Voltage (3.3V or 5.0V) or
Adjustable Output Voltage
• Space-Saving, 8-Lead MSOP
• Soft-Start Circuitry to Minimize In-Rush Current
• AEC-Q100 Qualified
Package Types
Applications:
• White LED Backlighting
MSOP (Fixed)
• Color Display Bias
PGOOD
1
2
3
4
8
7
6
5
SELECT
SHDN
C+
• Local 3V-to-5V Conversions
• Flash Memory Supply Voltage
• SIM Interface Supply for GSM Phones
• Smart Card Readers
V
MCP1252
MCP1253
OUT
V
IN
GND
C-
• PCMCIA Local 5V Supplies
MSOP (Adjustable)
PGOOD
1
2
3
4
8
FB
V
7
6
5
SHDN
C+
OUT
MCP1252
MCP1253
V
IN
GND
C-
2002-2014 Microchip Technology Inc.
DS20001752C-page 1
MCP1252/3
Functional Block Diagram
MCP1252-33X50
MCP1253-33X50
PGOOD
SELECT
140 k
-
+
173 k
+
-
84 mV
1.21V
+
+
100 k
+
-
+
200 mV
V
SHDN
OUT
C+
C-
Switch
Control
V
IN
GND
MCP1252-ADJ
MCP1253-ADJ
PGOOD
FB
-
+
+
-
84 mV
+
+
1.21V
+
-
+
200 mV
V
SHDN
OUT
C+
C-
Switch
Control
V
IN
GND
DS20001752C-page 2
2002-2014 Microchip Technology Inc.
MCP1252/3
†Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
Power Supply Voltage, V ...............................................6.0V
IN
Voltage on Any Pin w.r.t. GND ............... -0.3V to (V + 0.3V)
IN
Output Short Circuit Duration ................................continuous
Storage Temperature Range.........................-65°C to +150°C
Ambient Temperature with Power Applied ....-55°C to +125°C
Junction Temperature .................................................+150°C
ESD Ratings:
Human Body Model (1.5 k in Series with 100 pF)4 kV
Machine Body Model (200 pF, No Series Resistance)400V
ELECTRICAL CHARACTERISTICS
Electrical Specifications: Unless otherwise specified, all limits are specified for T = -40°C to +85°C ("I" Temperature), T = -40°C
A
A
to +125°C ("E" Temperature), SHDN = V , C = C
= 10 µF, C
= 1 µF, I
= 10 mA. Typical values are for T = +25°C.
IN
IN
OUT
FLY
OUT A
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Selectable Output - MCP1252-33X50, MCP1253-33X50: SELECT = V , V
= 3.3V
IN
OUT
Supply Voltage
V
2.1
—
5.5
V
IN
Output Voltage Accuracy
V
-2.5
±0.5
+2.5
%
2.3V V < 2.5V, I
80 mA
OUT
IN
OUT
2.5V V 5.5V, I
120 mA
IN
OUT
Output Current
I
80
120
1.4
100
150
—
—
—
—
mA
mA
V
2.3V V < 2.5V
OUT
IN
2.5V V 5.5V
IN
SELECT Logic Input Voltage High
V
MCP1252-33X50, MCP1253-33X50
IH
Selectable Output - MCP1252-33X50, MCP1253-33X50: SELECT = GND, V
= 5.0V
OUT
Supply Voltage
V
2.7
—
5.5
V
IN
Output Voltage Accuracy
V
-2.5
±0.5
+2.5
%
2.7V V < 3.0V, I
40 mA
120 mA
OUT
IN
OUT
OUT
3.0V V 5.5V, I
IN
Output Current
I
40
120
—
80
150
—
—
—
mA
V
2.7V V < 3.0V
OUT
IN
3.0V V 5.5V
IN
SELECT Logic Input Voltage Low
V
0.4
MCP1252-33X50, MCP1253-33X50
IL
Adjustable Output - MCP1252-ADJ, MCP1253-ADJ
Supply Voltage
V
2.0
1.5
—
—
5.5
5.5
V
V
V
IN
Output Voltage Adjustment Range
FB Regulation Voltage
ALL DEVICES
V
V
< 2 x V
OUT(MAX) IN
OUT
V
1.18
1.21
1.24
MCP1252-ADJ, MCP1253-ADJ
FB
Supply Current
I
—
—
—
—
60
200
0.1
81
120
—
µA
mA
µA
%
No load
DD
Output Short-Circuit Current
Shutdown Current
I
V
= GND, foldback current
OUT
SC
I
2.0
—
SHDN = 0V
SHDN
Power Efficiency
V
= 3.0V, V
= 5V
= 5V
IN
OUT
I
=120 mA
OUT
—
68
—
V
= 3.6V, V
OUT
IN
I
=120 mA
OUT
SHDN Logic Input Voltage Low
SHDN Logic Input Voltage High
PGOOD Output Voltage
V
—
1.4
—
—
—
0.4
—
—
—
—
V
V
V
V
V
IL
V
IH
P
0.01
I
= 0.5 mA
PGOOD
GOOD_VOL
PGOOD Threshold Voltage
PGOOD Hysteresis
V
—
0.93V
TH
OUT
OUT
V
—
0.04V
HYS
2002-2014 Microchip Technology Inc.
DS20001752C-page 3
MCP1252/3
AC CHARACTERISTICS
Electrical Specifications: Unless otherwise specified, all limits are specified for T = -40°C to +85°C ("I" Temperature), T = -40°C
A
A
to +125°C ("E" Temperature), SHDN = V , C = C
= 10 µF, C
= 1 µF, I
= 10 mA. Typical values are for T = +25°C.
IN
IN
OUT
FLY
OUT A
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
Internal Oscillator Frequency
FOSC
520
800
—
650
1000
50
780
1200
—
kHz MCP1252
MCP1253
Ripple Voltage
VRIP
mVp-p MCP1252
mVp-p MCP1253
µsec VIN = 3.6V, IOUT = 10 mA,
—
45
—
VOUT Wake-Up Time From Shutdown TWKUP
SHDN = VIH(MIN)
,
VOUT from 0 to 90% Nominal
Regulated Output Voltage
SELECT = VIN
—
—
200
300
—
—
SELECT = GND
TEMPERATURE SPECIFICATIONS
Parameters
Symbol
Min.
Typ.
Max.
Units
Conditions
Temperature Ranges:
Specified Temperature Range
TA
-40
-40
—
—
+85
+125
+125
°C
"I" Temperature range
"E" Temperature range
—
—
Maximum Operating Junction
Temperature
TJ
TA
°C
°C
Storage Temperature Range
-65
—
—
+150
—
Thermal Package Resistances:
Thermal Resistance, 8 Pin MSOP
JA
206
°C/W Single-Layer SEMI G42-88
board, Natural Convection
DS20001752C-page 4
2002-2014 Microchip Technology Inc.
MCP1252/3
2.0
TYPICAL PERFORMANCE CURVES
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, VIN = 3.6V, TA = 25°C, CIN = COUT = 10 µF, CFLY = 1 µF, all capacitors X7R ceramic.
100
90
80
70
60
50
40
30
20
10
0
5.05
5.04
5.03
5.02
5.01
5.00
4.99
10 mA
80 mA
10 mA
80 mA
120 mA
120 mA
MCP1252-33X50
SELECT = GND
OUT = 5.0V
MCP1252-33X50
SELECT = GND
VOUT = 5.0V
V
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
FIGURE 2-1:
Output Voltage vs. Supply
FIGURE 2-4:
Percent Efficiency vs.
Voltage (MCP1252-33X50).
Supply Voltage (MCP1252-33X50).
.
3.34
3.33
100
90
80
10 mA
70
80 mA
80 mA
60
120 mA
50
40
120 mA
10 mA
3.32
30
20
10
0
MCP1252-33X50
SELECT = VIN
VOUT = 3.3V
MCP1252-33X50
SELECT = VIN
VOUT = 3.3V
3.31
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
FIGURE 2-2:
Output Voltage vs. Supply
FIGURE 2-5:
Power Efficiency vs. Supply
Voltage (MCP1252-33X50).
Voltage (MCP1252-33X50).
3.02
3.01
3.00
2.99
100
90
80
10 mA
70
80 mA
120 mA
60
50
40
30
20
10
0
10 mA
80 mA
MCP1252-ADJ
OUT = 3.0V
MCP1252-ADJ
OUT = 3.0V
120 mA
V
V
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
FIGURE 2-6:
Voltage (MCP1252-ADJ).
Power Efficiency vs. Supply
FIGURE 2-3:
Voltage (MCP1252-ADJ).
Output Voltage vs. Supply
2002-2014 Microchip Technology Inc.
DS20001752C-page 5
MCP1252/3
Note: Unless otherwise indicated, VIN = 3.6V, TA = 25°C, CIN = COUT = 10 mF, CFLY = 1 mF, all capacitors X7R ceramic.
80
75
70
65
60
55
50
45
40
5.03
5.02
5.01
5.00
4.99
4.98
VIN = 5.5V
VIN = 3.6V
VIN = 2.7V
MCP1253-33X50
MCP1252-33X50
SELECT = GND
OUT = 5.0V
OUT = 120 mA
VIN = 2.3V
MCP1253-33X50
SELECT = GND
V
I
V
OUT = 5.0V, IOUT = 0 mA
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-7:
Output Voltage vs.
FIGURE 2-10:
Quiescent Current vs.
Temperature (MCP1252-33X50,
MCP1253-33X50).
Temperature (MCP1253-33X50).
80
3.33
VIN = 5.5V
75
MCP1253-33X50
VIN = 3.6V
70
3.32
3.31
3.30
3.29
3.28
65
MCP1252-33X50
VIN = 2.7V
60
SELECT = VIN
VOUT = 3.3V
55
50
45
40
MCP1252-33X50
SELECT = GND
VIN = 2.3V
IOUT = 120 mA
V
OUT = 5.0V, IOUT = 0 mA
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
FIGURE 2-11:
Quiescent Current vs.
FIGURE 2-8:
Output Voltage vs.
Temperature (MCP1252-33X50).
Temperature (MCP1252-33X50,
MCP1253-33X50).
FIGURE 2-12:
Load Transient Response.
FIGURE 2-9:
Line Transient Response.
DS20001752C-page 6
2002-2014 Microchip Technology Inc.
MCP1252/3
Note: Unless otherwise indicated, VIN = 3.6V, TA = 25°C, CIN = COUT = 10mF, CFLY = 1mF, all capacitors X7R ceramic.
70
60
50
80 mA
40
10 mA
120 mA
30
20
10
0
MCP1252-33X50
SELECT = GND
VOUT = 5.0V
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
FIGURE 2-13:
Output Voltage Ripple vs.
FIGURE 2-16:
Output Voltage Ripple vs.
Supply Voltage (MCP1252-33X50).
Time.
70
60
50
120 mA
40
80 mA
30
10 mA
MCP1252-33X50
SELECT = VIN
VOUT = 3.3V
20
10
0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Supply Voltage (V)
FIGURE 2-14:
Output Voltage Ripple vs.
FIGURE 2-17:
Output Voltage Ripple vs.
Supply Voltage (MCP1252-33X50).
Time.
FIGURE 2-15:
Start-Up (MCP1252-33X50).
FIGURE 2-18:
Start-Up (MCP1253-33X50).
2002-2014 Microchip Technology Inc.
DS20001752C-page 7
MCP1252/3
3.0
PIN FUNCTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
Pin No.
PIN FUNCTION TABLE
Name
Function
1
2
3
4
5
6
7
8
PGOOD
VOUT
VIN
Open-Drain Power GOOD Output
Regulated Output Voltage
Power Supply Input
Ground Terminal
GND
C-
Flying Capacitor Negative Terminal
C+
Flying Capacitor Positive Terminal
SHDN
SELECT
FB
Shutdown Mode, Active-Low Input
Output Voltage Select Pin (MCP1252-33X50, MCP1253-33X50)
Feedback Input Pin for Adjustable Output (MCP1252-ADJ, MCP1253-ADJ)
3.1
Open-Drain Power Good Output
(PGOOD)
3.6
Flying Capacitor Positive Terminal
(C+)
PGOOD is a high-impedance when the output voltage
is in regulation. A logic-low is asserted when the output
falls 7% (typical) below the nominal value. The PGOOD
output remains low until VOUT is within 3% (typical) of
its nominal value. On start-up, this pin indicates when
the output voltage reaches its final value. PGOOD is
high-impedance when SHDN is low.
The charge pump capacitor (flying capacitor) is used to
transfer charge from the input supply to the regulated
output.
Proper orientation is imperative when using a polarized
capacitor.
3.7
Shutdown Input (SHDN)
A logic-low signal applied to SHDN disables the device.
A logic-high signal applied to this pin allows normal
operation.
3.2
Regulated Output Voltage (V
)
OUT
Bypass to GND with a filter capacitor.
3.3
Power Supply Input (V )
IN
3.8
Select (SELECT) Input or
Feedback (FB) Input
It is recommended that VIN be tied to a ceramic bypass
capacitor.
MCP1252-33X50, MCP1253-33X50:
SELECT: Select Input Pin.
3.4
Ground (GND)
Connect SELECT to VIN for 3.3V fixed output. Connect
SELECT to GND for a 5.0V fixed output.
It is recommended that the ground pin be tied to a
ground plane for best performance.
MCP1252-ADJ, MCP1253-ADJ:
FB: Feedback Pin.
3.5
Flying Capacitor Negative
Terminal (C-)
A resistor divider connected to this pin determines the
adjustable VOUT value (1.5V to 5.5V).
The charge pump capacitor (flying capacitor) is used to
transfer charge from the input supply to the regulated
output.
It is recommended that a low ESR (equivalent series
resistance) capacitor be used.
DS20001752C-page 8
2002-2014 Microchip Technology Inc.
MCP1252/3
4.0
4.1
DEVICE OVERVIEW
Theory of Operation
START
The MCP1252 and MCP1253 family of devices employ
a switched capacitor charge pump to buck or boost an
input supply voltage (VIN) to a regulated output voltage.
Referring to the Functional Block Diagram and
Figure 4-1, the devices perform conversion and
regulation in three phases. When the devices are not in
shutdown mode and a steady-state condition has been
reached, the three phases are continuously cycled
through. The first phase transfers charge from the input
to the flying capacitor (CFLY) connected to pins C+ and
C-. This phase always occurs for half of the internal
oscillator period. During this phase, switches S1 and S2
are closed.
PHASE 1:
Charge Transfer
From V to C
IN
FLY
1
No
t1 = ----------------
2FOSC
Yes
PHASE 2:
Idle State
Once the first phase is complete, all switches are
opened and the second phase (idle phase) is entered.
The device compares the internal or external feedback
voltage with an internal reference. If the feedback volt-
age is below the regulation point, the device transitions
to the third phase.
Yes
V
> V
REF
FB
No
The third phase transfers energy from the flying capac-
itor to the output capacitor connected to VOUT and the
load. If regulation is maintained, the device returns to
the idle phase. If the charge transfer occurs for half the
internal oscillator period, more charge is needed in the
flying capacitor and the device transitions back to the
first phase.
PHASE 3:
Charge Transfer
From C
to C
FLY
OUT
Yes
1
t3 = ----------------
2FOSC
The regulation control is hysteretic, otherwise referred
to as a bang-bang control. The output is regulated
around a fixed reference with some hysteresis. As a
result, typically 50 mV of peak-to-peak ripple will be
observed at the output independent of load current.
The frequency of the output ripple, however, will be
influenced heavily by the load current and output
capacitance. The maximum frequency that will be
observed is equal to the internal oscillator frequency.
No
No
V
> V
REF
FB
Yes
FIGURE 4-1:
Flow Algorithm.
The devices automatically transition between buck or
boost operation. This provides a low-cost, compact and
simple solution for step-down/step-up DC/DC
conversion. This is especially true for battery-operated
applications that require a fixed output above or below
the input.
2002-2014 Microchip Technology Inc.
DS20001752C-page 9
MCP1252/3
4.2
Power Efficiency
4.6
Thermal Shutdown
The power efficiency, , is determined by the mode of
operation. In boost mode, the efficiency is
approximately half of a linear regulator. In buck mode,
the efficiency is approximately equal to that of a linear
regulator. The following formulas can be used to
approximate the power efficiency with any significant
amount of output current. At light loads, the quiescent
current of the device must be taken into consideration.
The MCP1252 and MCP1253 feature thermal
shutdown with temperature hysteresis. When the die
temperature exceeds 160°C, typically, the device shuts
down. When the die cools by 15°C, typically, the device
automatically turns back on. If high die temperature is
caused by output overload and the load is not removed,
the device will turn on and off, resulting in a pulse
output.
EQUATION 4-1:
5.0
APPLICATIONS
The MCP1252 and MCP1253 are inductorless,
positive-regulated, charge pump DC/DC converters. A
typical circuit configuration for the fixed output version
is depicted in Figure 5-1. The adjustable version is
depicted in Figure 5-2.
POUT
VOUT IOUT
VOUT
BOOST = ------------- = ------------------------------------ = -----------------
PIN
VIN 2 IOUT
VIN 2
POUT
VOUT IOUT
VOUT
BUCK = ------------- = ------------------------------- = -------------
PIN
VIN IOUT
VIN
SELECTABLE OUTPUT VOLTAGE
MCP1252-33X50
6
C+
+5.0V ±2.5%
+
2
V
OUT
C
FLY
4.3
Shutdown Mode
5
3
C-
C
R
OUT
PU
2.7V to 5.5V
Driving SHDN low places the MCP1252 or MCP1253 in
a low-power shutdown mode. This disables the charge
pump switches, oscillator and control logic, reducing
the quiescent current to 0.1 µA (typical). The PGOOD
output is in a high-impedance state during shutdown.
V
IN
1
8
+
PGOOD
SELECT
C
IN
PGOOD Flag
®
7
To PIC
SHDN
Microcontroller
ON
GND
4
4.4
PGOOD Output
OFF
Shutdown
Control
C
C
C
R
= 1 µF
FLY
= 10 µF
IN
OUT
The PGOOD output is an open-drain output that sinks
current when the regulator output voltage falls below
0.93VOUT (typical). The output voltage can either be
fixed when the selectable output device is chosen
(MCP1252-33X50, MCP1253-33X50) or adjustable
from an external resistive divider when the adjustable
device is chosen (MCP1252-ADJ, MCP1253-ADJ). If
the regulator output voltage falls below 0.93VOUT
(typical) for less than 200 µsec and then recovers,
glitch-immunity circuits prevent the PGOOD signal
from transitioning low. A 10 k to 1 M pull-up resistor
from PGOOD to VOUT may be used to provide a logic
output. Connect PGOOD to GND or leave unconnected
if not used.
= 10 µF
= 100 k
PU
FIGURE 5-1:
Typical Circuit Configuration
for Fixed Output Device.
ADJUSTABLE OUTPUT VOLTAGE
MCP1252-ADJ
6
5
C+
+4.0V
2
V
OUT
C
FLY
+ C
OUT
R
PU
C-
2.7V to 5.5V
R
1
3
7
V
IN
1
8
+
PGOOD
FB
C
IN
PGOOD Flag
To PIC
Microcontroller
®
4.5
Soft-Start and Short-Circuit
Protection
SHDN
GND
ON
R
2
4
OFF
Shutdown
Control
The MCP1252 and MCP1253 feature foldback short-
circuit protection. This circuitry provides an internal
soft-start function by limiting in-rush current during
startup and also limits the output current to 200 mA
(typical) if the output is shorted to GND. The internal
soft-start circuitry requires approximately 300 µsec,
typical with a 5V output, from either initial power-up or
release from shutdown for the output voltage to be in
regulation.
C
C
C
R
= 1 µF
FLY
= 10 µF
IN
OUT
= 10 µF
= 100 k
V
= 1.21V (1 + R /R )
1 2
OUT
PU
R = 23.2 k
R = 10 k
1
2
FIGURE 5-2:
Typical Circuit Configuration
for Adjustable Output Device.
DS20001752C-page 10
2002-2014 Microchip Technology Inc.
MCP1252/3
Note that the tolerance of the external resistors will
have an effect on the accuracy of the output voltage.
For optimum results, it is recommended that the
external resistors have a tolerance no larger than 1%.
5.1
Capacitor Selection
The style and value of capacitors used with the
MCP1252 and MCP1253 family of devices determine
several important parameters such as output voltage
ripple and charge pump strength. To minimize noise
and ripple, it is recommended that low ESR (0.1 )
capacitors be used for both CIN and COUT. These
capacitors should be either ceramic or tantalum and
should be 10 µF or higher. Aluminum capacitors are not
recommended because of their high ESR.
5.3
Recommended Layout
The MCP1252 and MCP1253 family of devices transfer
charge at high switching frequencies, producing fast,
high peak, transient currents. As a result, any stray
inductance in the component layout will produce
unwanted noise in the system. Proper board layout
techniques are required to ensure optimum perfor-
mance. Figure 5-3 depicts the recommended board
layout. The input capacitor connected between VIN and
GND, and the output capacitor connected between
VOUT and GND, are 10 µF ceramic, X7R dielectric, in
1206 packages. The flying capacitor connected
between C+ and C- is a 1 µF ceramic, X7R dielectric in
a 0805 package. The layout is scaled 3:1.
If the source impedance to VIN is very low, up to several
megahertz, CIN may not be required. Alternatively, a
somewhat smaller value of CIN may be substituted for
the recommended 10 µF, but will not be as effective in
preventing ripple on the VIN pin.
The value of COUT controls the amount of output volt-
age ripple present on VOUT. Increasing the size of
COUT will reduce output ripple at the expense of a
slower turn-on time from shutdown and a higher in-rush
current.
The flying capacitor (CFLY) controls the strength of the
charge pump. In order to achieve the maximum rated
output current (120 mA), it is necessary to have at least
1 µF of capacitance for the flying capacitor. A smaller
flying capacitor delivers less charge per clock cycle to
the output capacitor, resulting in lower output ripple.
The output ripple is reduced at the expense of maxi-
mum output current and efficiency.
PGOOD
V
OUT
SELECT
SHDN
C+
GND
C-
V
IN
5.2
Output Voltage Setting
The MCP1252-33X50 and MCP1253-33X50 feedback
controllers select between an internally-set, regulated
output voltage (3.3V or 5.0V). Connect SELECT to
GND for a regulated 5.0V output and connect SELECT
to VIN for a regulated 3.3V output.
FIGURE 5-3:
Circuit Board Layout.
Recommended Printed
The MCP1252-ADJ and MCP1253-ADJ utilize an
external resistor divider that allows the output voltage
to be adjusted between 1.5V and 5.5V. For an adjust-
able output, connect a resistor between VOUT and FB
(R1) and another resistor between FB and GND (R2). In
the following equation, choose R2 to be less than or
equal to 30 k and calculate R1 from the following
formula:
EQUATION 5-1:
R
= R V
V – 1
OUT FB
1
2
and:
EQUATION 5-2:
V
= V 1 + R R
FB
OUT
1
2
where:
V
is the desired output voltage from 1.5V to 5.5V
OUT
V
is the internal regulation voltage, nominally 1.21V
FB
2002-2014 Microchip Technology Inc.
DS20001752C-page 11
MCP1252/3
6.0
TYPICAL APPLICATION CIRCUITS
Single Cell Lithium-Ion Battery To 5V Converter
1 µF
5
6
C-
C+
3
7
1
2
8
4
V
V
5V
IN
OUT
10 µF
Single
Li-Ion
Cell
10 µF
+
-
SHDN
SELECT
GND
100 k
PGOOD
MCP1252-33X50
White LED Bias
1 µF
5
6
C-
C+
UP TO 6 WHITE LEDS
3
2
V
V
IN
OUT
10 µF
Single
Li-Ion
Cell
10 µF
+
-
7
1
8
4
SHDN
SELECT
GND
100 k
59 59 59 59 59 59
PGOOD
MCP1252-ADJ
PWM Contrast
Control
Alternative White LED Bias
1 µF
5
6
C-
C+
UP TO 6 WHITE LEDS
3
7
1
2
8
4
V
V
IN
OUT
24k
10k
10 µF
Single
Li-Ion
Cell
10 µF
+
-
SHDN
SELECT
GND
10 10 10 10 10 10
100 k
PGOOD
MCP1252-ADJ
PWM Contrast
Control
DS20001752C-page 12
2002-2014 Microchip Technology Inc.
MCP1252/3
7.0
7.1
PACKAGING INFORMATION
Package Marking
8-Lead MSOP (Fixed)
Example:
1252SX
412256
8-Lead MSOP (Adjustable)
Example:
1253DJ
1253EX
412256
412256
OR
Legend: XX...X Customer-specific information
Y
Year code (last digit of calendar year)
YY
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
WW
NNN
Pb-free JEDEC® designator for Matte Tin (Sn)
e
3
e
3
*
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
2002-2014 Microchip Technology Inc.
DS20001752C-page 13
MCP1252/3
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS20001752C-page 14
2002-2014 Microchip Technology Inc.
MCP1252/3
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2002-2014 Microchip Technology Inc.
DS20001752C-page 15
MCP1252/3
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS20001752C-page 16
2002-2014 Microchip Technology Inc.
MCP1252/3
APPENDIX A: REVISION HISTORY
Revision C (July 2014)
The following is the list of modifications:
1. Added the Extended Temperature (E) option
and related information throughout the
document.
Revision B (January 2013)
The following is the list of modifications:
1. Added a note to each package outline drawing.
2002-2014 Microchip Technology Inc.
DS20001752C-page 17
MCP1252/3
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
(1)
X
/XX
PART NO.
Device
[X]
-XXX
Examples:
Temperature Package
Option Range
Tape and Reel
Option
Voltage
a)
b)
c)
MCP1252-33X50I/MS: Low-Noise, Posi-
tive-Regulated Charge Pump, Fixed Output
MCP1252-ADJI/MS: Low-Noise, Positive-
Regulated Charge Pump, Adjustable Output
MCP1252T-33X50I/MS: Tape and Reel,
Low-Noise, Positive-Regulated Charge
Pump, Fixed Output
MCP1252: Low-Noise, Positive-Regulated Charge Pump
MCP1252T: Low-Noise, Positive-Regulated Charge Pump
(Tape and Reel)
MCP1253: Low-Noise, Positive-Regulated Charge Pump
MCP1253T: Low-Noise, Positive-Regulated Charge Pump
(Tape and Reel)
a)
b)
MCP1253-33X50I/MS: Low-Noise, Posi-
tive-Regulated Charge Pump, Fixed Output
MCP1253-ADJI/MS:
Low-Noise, Posi-
Tape and Reel Option:
Output Voltage:
T
=
Tape and Reel(1)
tive-Regulated Charge Pump, Adjustable
Output
c)
MCP1253T-ADJI/MS: Tape and Reel,
Low-Noise, Positive-Regulated Charge
Pump, Adjustable Output
ADJ
= Adjustable Voltage
33X50 = Selectable Voltage
Temperature Range:
Package:
I
E
=
=
-40C to +85C (Industrial)
Note 1:
Tape and Reel identifier only appears in the
catalog part number description. This
identifier is used for ordering purposes and
is not printed on the device package. Check
with your Microchip Sales Office for package
availability with the Tape and Reel option.
-40C to +125C (Extended) (MCP1253 only)
MS
=
Plastic Micro Small Outline (MSOP), 8-lead
DS20001752C-page 18
2002-2014 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer,
LANCheck, MediaLB, MOST, MOST logo, MPLAB,
32
OptoLyzer, PIC, PICSTART, PIC logo, RightTouch, SpyNIC,
SST, SST Logo, SuperFlash and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo,
CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit
Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet,
KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo,
MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code
Generation, PICDEM, PICDEM.net, PICkit, PICtail,
RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total
Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademarks of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2002-2014, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
ISBN: 978-1-63276-373-0
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
== ISO/TS 16949 ==
2002-2014 Microchip Technology Inc.
DS20001752C-page 19
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-3019-1500
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Austin, TX
Tel: 512-257-3370
Germany - Pforzheim
Tel: 49-7231-424750
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Italy - Venice
Tel: 39-049-7625286
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Poland - Warsaw
Tel: 48-22-3325737
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Sweden - Stockholm
Tel: 46-8-5090-4654
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Detroit
Novi, MI
Tel: 248-848-4000
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Houston, TX
Tel: 281-894-5983
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Los Angeles
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
03/25/14
DS20001752C-page 20
2002-2014 Microchip Technology Inc.
相关型号:
©2020 ICPDF网 联系我们和版权申明