MCP3208-BI/P [MICROCHIP]
2.7V 4-Channel/8-Channel 12-Bit A/D Converters with SPI⑩ Serial Interface; 2.7V 4通道/ 8通道12位与SPI⑩串行接口的A / D转换器型号: | MCP3208-BI/P |
厂家: | MICROCHIP |
描述: | 2.7V 4-Channel/8-Channel 12-Bit A/D Converters with SPI⑩ Serial Interface |
文件: | 总34页 (文件大小:598K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCP3204/3208
2.7V 4-Channel/8-Channel 12-Bit A/D Converters
with SPI™ Serial Interface
Features
Description
• 12-bit resolution
The Microchip Technology Inc. MCP3204/3208
devices are successive approximation 12-bit Analog-
to-Digital (A/D) Converters with on-board sample and
hold circuitry. The MCP3204 is programmable to pro-
vide two pseudo-differential input pairs or four single-
ended inputs. The MCP3208 is programmable to pro-
vide four pseudo-differential input pairs or eight single-
ended inputs. Differential Nonlinearity (DNL) is speci-
fied at ±1 LSB, while Integral Nonlinearity (INL) is
offered in ±1 LSB (MCP3204/3208-B) and ±2 LSB
(MCP3204/3208-C) versions.
• ± 1 LSB max DNL
• ± 1 LSB max INL (MCP3204/3208-B)
• ± 2 LSB max INL (MCP3204/3208-C)
• 4 (MCP3204) or 8 (MCP3208) input channels
• Analog inputs programmable as single-ended or
pseudo-differential pairs
• On-chip sample and hold
• SPI serial interface (modes 0,0 and 1,1)
• Single supply operation: 2.7V - 5.5V
• 100 ksps max. sampling rate at VDD = 5V
• 50 ksps max. sampling rate at VDD = 2.7V
• Low power CMOS technology:
Communication with the devices is accomplished using
a simple serial interface compatible with the SPI proto-
col. The devices are capable of conversion rates of up
to 100 ksps. The MCP3204/3208 devices operate over
a broad voltage range (2.7V - 5.5V). Low current
design permits operation with typical standby and
active currents of only 500 nA and 320 µA, respec-
tively. The MCP3204 is offered in 14-pin PDIP, 150 mil
SOIC and TSSOP packages. The MCP3208 is offered
in 16-pin PDIP and SOIC packages.
- 500 nA typical standby current, 2 µA max.
- 400 µA max. active current at 5V
• Industrial temp range: -40°C to +85°C
• Available in PDIP, SOIC and TSSOP packages
Applications
• Sensor Interface
Functional Block Diagram
• Process Control
VSS
VDD
• Data Acquisition
VREF
• Battery Operated Systems
CH0
CH1
Input
Channel
Mux
Package Types
PDIP, SOIC, TSSOP
DAC
CH7*
Comparator
CH0
CH1
CH2
CH3
NC
1
2
3
4
5
6
7
14
13
VDD
VREF
12-Bit SAR
Sample
12 AGND
and
CLK
11
10
9
Hold
DOUT
DIN
Shift
Register
NC
Control Logic
DGND
8
CS/SHDN
PDIP, SOIC
CS/SHDN DIN
CLK
DOUT
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
1
16 VDD
VREF
15
14 AGND
13 CLK
* Note: Channels 5-7 available on MCP3208 Only
2
3
4
5
12 DOUT
DIN
6
7
8
11
10
9
CS/SHDN
DGND
© 2007 Microchip Technology Inc.
DS21298D-page 1
MCP3204/3208
1.0
ELECTRICAL
PIN FUNCTION TABLE
CHARACTERISTICS
Name
Function
Absolute Maximum Ratings*
VDD
+2.7V to 5.5V Power Supply
Digital Ground
DGND
AGND
CH0-CH7
CLK
V
...................................................................................7.0V
DD
Analog Ground
All inputs and outputs w.r.t. V ............... -0.6V to V +0.6V
SS
DD
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-65°C to +125°C
Soldering temperature of leads (10 seconds) .............+300°C
ESD protection on all pins.............................................> 4 kV
Analog Inputs
Serial Clock
DIN
Serial Data In
DOUT
Serial Data Out
*Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
CS/SHDN
VREF
Chip Select/Shutdown Input
Reference Voltage Input
ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5V, VSS = 0V, VREF = 5V,
AMB = -40°C to +85°C,fSAMPLE = 100 ksps and fCLK = 20*fSAMPLE
T
Parameters
Sym
Min
Typ
Max
Units
Conditions
Conversion Rate
Conversion Time
tCONV
—
—
12
clock
cycles
Analog Input Sample Time
Throughput Rate
tSAMPLE
fSAMPLE
1.5
clock
cycles
—
—
—
—
100
50
ksps VDD = VREF = 5V
ksps VDD = VREF = 2.7V
DC Accuracy
Resolution
12
bits
Integral Nonlinearity
INL
—
—
±0.75
±1.0
±1
±2
LSB MCP3204/3208-B
MCP3204/3208-C
Differential Nonlinearity
DNL
—
±0.5
±1
LSB No missing codes
over-temperature
Offset Error
—
—
±1.25
±1.25
±3
±5
LSB
LSB
Gain Error
Dynamic Performance
Total Harmonic Distortion
—
—
-82
72
—
—
dB VIN = 0.1V to 4.9V@1 kHz
dB VIN = 0.1V to 4.9V@1 kHz
Signal to Noise and Distortion
(SINAD)
Spurious Free Dynamic
Range
—
86
—
dB VIN = 0.1V to 4.9V@1 kHz
Reference Input
Voltage Range
Current Drain
0.25
—
VDD
V
Note 2
—
—
100
0.001
150
3.0
µA
µA CS = VDD = 5V
Note 1: This parameter is established by characterization and not 100% tested.
2: See graphs that relate linearity performance to VREF levels.
3: Because the sample cap will eventually lose charge, effective clock rates below 10 kHz can affect linearity
performance, particularly at elevated temperatures. See Section 6.2, “Maintaining Minimum Clock Speed”,
for more information.
DS21298D-page 2
© 2007 Microchip Technology Inc.
MCP3204/3208
ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5V, VSS = 0V, VREF = 5V,
TAMB = -40°C to +85°C,fSAMPLE = 100 ksps and fCLK = 20*fSAMPLE
Parameters
Sym
Min
Typ
Max
Units
Conditions
Analog Inputs
Input Voltage Range for CH0-
CH7 in Single-Ended Mode
VSS
—
VREF
V
Input Voltage Range for IN+ in
pseudo-differential Mode
Input Voltage Range for IN- in
pseudo-differential Mode
IN-
—
—
V
REF+IN-
V
SS-100
VSS+100
mV
Leakage Current
—
—
—
0.001
1000
20
±1
—
—
µA
Ω
Switch Resistance
See Figure 4-1
Sample Capacitor
pF
See Figure 4-1
Digital Input/Output
Data Coding Format
High Level Input Voltage
Low Level Input Voltage
High Level Output Voltage
Low Level Output Voltage
Input Leakage Current
Output Leakage Current
Straight Binary
VIH
VIL
0.7 VDD
—
—
—
—
—
—
—
—
—
0.3 VDD
—
V
V
V
V
VOH
VOL
4.1
IOH = -1 mA, VDD = 4.5V
IOL = 1 mA, VDD = 4.5V
—
0.4
ILI
-10
-10
—
10
µA VIN = VSS or VDD
µA VOUT = VSS or VDD
ILO
10
Pin Capacitance
(All Inputs/Outputs)
CIN,COUT
10
pF
VDD = 5.0V (Note 1)
TAMB = 25°C, f = 1 MHz
Timing Parameters
Clock Frequency
fCLK
—
—
—
—
2.0
1.0
MHz VDD = 5V (Note 3)
MHz
VDD = 2.7V (Note 3)
Clock High Time
Clock Low Time
tHI
tLO
250
250
100
—
—
—
—
—
—
ns
ns
CS Fall To First Rising CLK
Edge
tSUCS
ns
Data Input Setup Time
Data Input Hold Time
CLK Fall To Output Data Valid
CLK Fall To Output Enable
CS Rise To Output Disable
CS Disable Time
tSU
tHD
tDO
tEN
tDIS
tCSH
tR
—
—
—
—
—
—
—
—
—
—
50
50
ns
ns
ns
ns
ns
ns
ns
ns
—
200
200
100
—
See Figures 1-2 and 1-3
See Figures 1-2 and 1-3
See Figures 1-2 and 1-3
—
—
500
—
DOUT Rise Time
100
100
See Figures 1-2 and 1-3 (Note 1)
See Figures 1-2 and 1-3 (Note 1)
DOUT Fall Time
tF
—
Power Requirements
Operating Voltage
VDD
IDD
2.7
—
5.5
V
Operating Current
—
—
320
225
400
—
µA VDD=VREF = 5V, DOUT unloaded
VDD=VREF = 2.7V, DOUT unloaded
Standby Current
IDDS
—
0.5
2.0
µA CS = VDD = 5.0V
Note 1: This parameter is established by characterization and not 100% tested.
2: See graphs that relate linearity performance to VREF levels.
3: Because the sample cap will eventually lose charge, effective clock rates below 10 kHz can affect linearity
performance, particularly at elevated temperatures. See Section 6.2, “Maintaining Minimum Clock Speed”,
for more information.
© 2007 Microchip Technology Inc.
DS21298D-page 3
MCP3204/3208
ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5V, VSS = 0V, VREF = 5V,
TAMB = -40°C to +85°C,fSAMPLE = 100 ksps and fCLK = 20*fSAMPLE
Parameters
Sym
Min
Typ
Max
Units
Conditions
Temperature Ranges
Specified Temperature Range
TA
TA
-40
-40
—
—
+85
+85
°C
°C
Operating Temperature
Range
Storage Temperature Range
TA
-65
—
+150
°C
Thermal Package Resistance
Thermal Resistance,
14L-PDIP
θJA
θJA
θJA
θJA
θJA
—
—
—
—
—
70
108
100
70
—
—
—
—
—
°C/W
°C/W
°C/W
°C/W
°C/W
Thermal Resistance,
14L-SOIC
Thermal Resistance,
14L-TSSOP
Thermal Resistance,
16L-PDIP
Thermal Resistance,
16L-SOIC
90
Note 1: This parameter is established by characterization and not 100% tested.
2: See graphs that relate linearity performance to VREF levels.
3: Because the sample cap will eventually lose charge, effective clock rates below 10 kHz can affect linearity
performance, particularly at elevated temperatures. See Section 6.2, “Maintaining Minimum Clock Speed”,
for more information.
t
CSH
CS
t
SUCS
t
t
LO
HI
CLK
t
t
HD
SU
D
IN
MSB IN
t
t
t
DIS
t
R
F
DO
t
EN
D
OUT
Null Bit
MSB OUT
LSB
FIGURE 1-1:
Serial Interface Timing.
DS21298D-page 4
© 2007 Microchip Technology Inc.
MCP3204/3208
Test Point
1.4V
V
DD
t
t
DIS Waveform 2
Waveform
3 kΩ
Test Point
V
/2
3 kΩ
DD
t
D
D
EN
OUT
OUT
100 pF
DIS Waveform 1
C = 100 pF
L
V
SS
Voltage Waveforms for t , t
R
F
Voltage Waveforms for t
EN
V
OH
V
OL
D
OUT
CS
t
t
F
R
1
2
3
4
CLK
Voltage Waveforms for t
DO
B11
D
OUT
CLK
t
EN
t
DO
Voltage Waveforms for t
DIS
D
OUT
V
IH
CS
D
FIGURE 1-2:
Load Circuit for tR, tF, tDO.
OUT
90%
10%
Waveform 1*
T
DIS
D
OUT
Waveform 2†
* Waveform 1 is for an output with internal
conditions such that the output is high,
unless disabled by the output control.
† Waveform 2 is for an output with internal
conditions such that the output is low,
unless disabled by the output control.
FIGURE 1-3:
Load circuit for tDIS and tEN.
© 2007 Microchip Technology Inc.
DS21298D-page 5
MCP3204/3208
2.0
TYPICAL PERFORMANCE CHARACTERISTICS
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, VDD = VREF = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
1.0
2.0
VDD = VREF = 2.7 V
0.8
0.6
Positive INL
1.5
1.0
0.4
Positive INL
0.5
0.2
0.0
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.5
-1.0
-1.5
-2.0
Negative INL
Negative INL
0
10
20
30
40
50
60
70
80
0
25
50
75
100
125
150
Sample Rate (ksps)
Sample Rate (ksps)
FIGURE 2-1:
Integral Nonlinearity (INL)
FIGURE 2-4:
Integral Nonlinearity (INL)
vs. Sample Rate.
vs. Sample Rate (VDD = 2.7V).
2.5
2.0
1.5
1.0
2.0
1.5
Positive INL
1.0
Positive INL
0.5
0.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
-0.5
Negative INL
-1.0
Negative INL
-1.5
-2.0
0
1
2
3
4
5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
VREF (V)
VREF (V)
FIGURE 2-2:
vs. VREF
Integral Nonlinearity (INL)
FIGURE 2-5:
vs. VREF (VDD = 2.7V).
Integral Nonlinearity (INL)
.
1.0
1.0
0.8
VDD = VREF = 2.7 V
0.8
FSAMPLE = 50 ksps
0.6
0.6
0.4
0.2
0.4
0.2
0.0
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
0
512
1024 1536 2048 2560 3072 3584 4096
Digital Code
0
512
1024 1536 2048 2560 3072 3584 4096
Digital Code
FIGURE 2-3:
Integral Nonlinearity (INL)
FIGURE 2-6:
Integral Nonlinearity (INL)
vs. Code (Representative Part).
vs. Code (Representative Part, VDD = 2.7V).
DS21298D-page 6
© 2007 Microchip Technology Inc.
MCP3204/3208
Note: Unless otherwise indicated, VDD = VREF = 5 V, VSS = 0 V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
1.0
0.8
1.0
0.8
VDD = VREF = 2.7 V
FSAMPLE = 50 ksps
Positive INL
0.6
0.6
Positive INL
0.4
0.4
0.2
0.2
0.0
0.0
Negative INL
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
Negative INL
25
-50
-25
0
50
75
100
-50
-25
0
25
50
75
100
Temperature (°C)
Temperature (°C)
FIGURE 2-7:
Integral Nonlinearity (INL)
FIGURE 2-10:
Integral Nonlinearity (INL)
vs. Temperature.
vs. Temperature (VDD = 2.7V).
2.0
1.0
0.8
VDD = VREF = 2.7 V
1.5
0.6
1.0
0.5
0.4
0.2
Positive DNL
Positive DNL
Negative DNL
0.0
-0.5
-1.0
-1.5
-2.0
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
Negative DNL
0
25
50
75
100
125
150
0
10
20
30
40
50
60
70
80
Sample Rate (ksps)
Sample Rate (ksps)
FIGURE 2-8:
Differential Nonlinearity
FIGURE 2-11:
Differential Nonlinearity
(DNL) vs. Sample Rate.
(DNL) vs. Sample Rate (VDD = 2.7V).
3.0
2.0
3.0
VDD = VREF = 2.7 V
F
SAMPLE = 50 ksps
2.0
1.0
Positive DNL
1.0
Positive DNL
0.0
0.0
Negative DNL
Negative DNL
-1.0
-2.0
-3.0
-1.0
-2.0
-3.0
0
1
2
3
4
5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
VREF (V)
VREF (V)
FIGURE 2-9:
(DNL) vs. VREF
Differential Nonlinearity
FIGURE 2-12:
(DNL) vs. VREF (VDD = 2.7V).
Differential Nonlinearity
.
© 2007 Microchip Technology Inc.
DS21298D-page 7
MCP3204/3208
Note: Unless otherwise indicated, VDD = VREF = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
1.0
0.8
1.0
0.8
VDD = VREF = 2.7 V
SAMPLE = 50 ksps
F
0.6
0.6
0.4
0.4
0.2
0.2
0.0
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
0
512
1024 1536 2048 2560 3072 3584 4096
Digital Code
0
512
1024 1536 2048 2560 3072 3584 4096
Digital Code
FIGURE 2-13:
Differential Nonlinearity
FIGURE 2-16:
Differential Nonlinearity
(DNL) vs. Code (Representative Part).
(DNL) vs. Code (Representative Part, VDD
2.7V).
=
1.0
0.8
0.6
1.0
VDD = VREF = 2.7 V
0.8
FSAMPLE = 50 ksps
0.6
0.4
0.4
Positive DNL
Positive DNL
0.2
0.0
0.2
0.0
-0.2
-0.2
-0.4
-0.6
-0.8
-1.0
-0.4
Negative DNL
Negative DNL
-0.6
-0.8
-1.0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Temperature (°C)
Temperature (°C)
FIGURE 2-14:
Differential Nonlinearity
FIGURE 2-17:
Differential Nonlinearity
(DNL) vs. Temperature.
(DNL) vs. Temperature (VDD = 2.7V).
4
3
20
18
16
VDD = VREF = 2.7 V
SAMPLE = 50 ksps
F
2
1
VDD = VREF = 5V
14
FSAMPLE = 100 ksps
12
10
8
0
-1
-2
-3
-4
VDD = VREF = 2.7V
FSAMPLE = 50 ksps
6
VDD = VREF = 5 V
SAMPLE = 100 ksps
4
F
2
0
0
1
2
3
4
5
0
1
2
3
4
5
VREF (V)
VREF (V)
FIGURE 2-15:
Gain Error vs. VREF.
FIGURE 2-18:
Offset Error vs. VREF.
DS21298D-page 8
© 2007 Microchip Technology Inc.
MCP3204/3208
Note: Unless otherwise indicated, VDD = VREF = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0.2
0.0
VDD = VREF = 2.7 V
FSAMPLE = 50 ksps
VDD = VREF = 5 V
FSAMPLE = 100 ksps
-0.2
-0.4
-0.6
-0.8
-1.0
-1.2
-1.4
-1.6
-1.8
VDD = VREF = 2.7 V
FSAMPLE = 50 ksps
VDD = VREF = 5 V
F
SAMPLE = 100 ksps
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Temperature (°C)
Temperature (°C)
FIGURE 2-19:
Gain Error vs. Temperature.
FIGURE 2-22:
Offset Error vs.
Temperature.
100
90
80
70
60
50
40
30
20
10
100
90
VDD = VREF = 5 V
SAMPLE = 100 ksps
VDD = VREF = 5 V
F
F
SAMPLE = 100 ksps
80
70
60
VDD = VREF = 2.7 V
SAMPLE = 50 ksps
50
40
30
20
10
0
F
VDD = VREF = 2.7V
F
SAMPLE = 50 ksps
0
1
10
100
1
10
100
Input Frequency (kHz)
Input Frequency (kHz)
FIGURE 2-20:
Signal to Noise (SNR) vs.
FIGURE 2-23:
Signal to Noise and
Input Frequency.
Distortion (SINAD) vs. Input Frequency.
0
-10
-20
-30
-40
80
VDD = VREF = 5 V
FSAMPLE = 100 ksps
70
60
50
VDD = VREF = 2.7V
SAMPLE = 50 ksps
F
VDD = VREF = 2.7 V
SAMPLE = 50 ksps
-50
-60
F
40
30
20
10
0
-70
-80
VDD = VREF = 5V
FSAMPLE = 100 ksps
-90
-100
1
10
100
-40
-35
-30
-25
-20
-15
-10
-5
0
Input Frequency (kHz)
Input Signal Level (dB)
FIGURE 2-21:
Total Harmonic Distortion
FIGURE 2-24:
Signal to Noise and
(THD) vs. Input Frequency.
Distortion (SINAD) vs. Input Signal Level.
© 2007 Microchip Technology Inc.
DS21298D-page 9
MCP3204/3208
Note: Unless otherwise indicated, VDD = VREF = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
12.0
12.00
11.75
11.50
11.25
11.00
10.75
10.50
10.25
10.00
9.75
11.5
11.0
10.5
10.0
9.5
VDD = VREF = 5 V
FSAMPLE =100 ksps
VDD = VREF = 5 V
SAMPLE = 100 ksps
VDD = VREF = 2.7 V
SAMPLE = 50 ksps
F
F
VDD = VREF = 2.7 V
FSAMPLE = 50 ksps
9.0
9.50
8.5
9.25
9.00
8.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
VREF (V)
1
10
100
Input Frequency (kHz)
FIGURE 2-25:
Effective Number of Bits
FIGURE 2-28:
Effective Number of Bits
(ENOB) vs. VREF
.
(ENOB) vs. Input Frequency.
0
-10
-20
-30
-40
-50
-60
-70
-80
100
90
VDD = VREF = 5 V
FSAMPLE = 100 ksps
80
70
60
VDD = VREF = 2.7 V
SAMPLE = 50 ksps
50
40
30
20
10
0
F
1
10
100
1000
10000
1
10
100
Input Frequency (kHz)
Ripple Frequency (kHz)
FIGURE 2-26:
Spurious Free Dynamic
FIGURE 2-29:
Power Supply Rejection
Range (SFDR) vs. Input Frequency.
(PSR) vs. Ripple Frequency.
0
-10
0
VDD = VREF = 5 V
VDD = VREF = 2.7 V
FSAMPLE = 50 ksps
-10
-20
F
F
SAMPLE = 100 ksps
INPUT = 9.985 kHz
-20
F
INPUT = 998.76 Hz
-30
-30
4096 points
4096 points
-40
-40
-50
-50
-60
-60
-70
-70
-80
-80
-90
-90
-100
-110
-120
-130
-100
-110
-120
-130
0
5000
10000
15000
20000
25000
0
10000
20000
30000
40000
50000
Frequency (Hz)
Frequency (Hz)
FIGURE 2-27:
Frequency Spectrum of
FIGURE 2-30:
Frequency Spectrum of
10 kHz input (Representative Part).
1 kHz input (Representative Part, VDD = 2.7V).
DS21298D-page 10
© 2007 Microchip Technology Inc.
MCP3204/3208
Note: Unless otherwise indicated, VDD = VREF = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
500
450
400
350
300
250
200
150
100
50
100
90
80
70
60
50
40
30
20
10
0
VREF = VDD
All points at FCLK = 2 MHz except
at VREF = VDD = 2.5 V, FCLK = 1 MHz
VREF = VDD
All points at FCLK = 2 MHz, except
at VREF = VDD = 2.5 V, FCLK = 1 MHz
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (V)
VDD (V)
FIGURE 2-31:
IDD vs. VDD
.
FIGURE 2-34:
IREF vs. VDD.
100
90
80
70
60
50
40
30
20
10
400
350
300
250
200
150
100
50
VDD = VREF = 5 V
VDD = VREF = 5 V
VDD = VREF = 2.7 V
VDD = VREF = 2.7 V
0
0
10
100
1000
10000
10
100
1000
10000
Clock Frequency (kHz)
Clock Frequency (kHz)
FIGURE 2-32:
IDD vs. Clock Frequency.
FIGURE 2-35:
IREF vs. Clock Frequency.
400
100
90
80
70
60
50
40
30
20
10
0
VDD = VREF = 5 V
FCLK = 2 MHz
VDD = VREF = 5 V
FCLK = 2 MHz
350
300
250
200
150
100
50
VDD = VREF = 2.7 V
CLK = 1 MHz
F
VDD = VREF = 2.7 V
CLK = 1 MHz
F
0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
75
100
Temperature (°C)
Temperature (°C)
FIGURE 2-33:
IDD vs. Temperature.
FIGURE 2-36:
IREF vs. Temperature.
© 2007 Microchip Technology Inc.
DS21298D-page 11
MCP3204/3208
Note: Unless otherwise indicated, VDD = VREF = 5V, VSS = 0V, fSAMPLE = 100 ksps, fCLK = 20* fSAMPLE,TA = 25°C.
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
80
70
60
50
40
30
20
10
0
VREF = CS = VDD
VDD = VREF = 5 V
CLK = 2 MHz
F
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
-50
-25
0
25
50
75
100
VDD (V)
Temperature (°C)
FIGURE 2-37:
IDDS vs. VDD
.
FIGURE 2-39:
Analog Input Leakage
Current vs. Temperature.
100.00
VDD = VREF = CS = 5 V
10.00
1.00
0.10
0.01
-50
-25
0
25
50
75
100
Temperature (°C)
FIGURE 2-38:
IDDS vs. Temperature.
DS21298D-page 12
© 2007 Microchip Technology Inc.
MCP3204/3208
3.7
Chip Select/Shutdown (CS/SHDN)
3.0
PIN DESCRIPTIONS
The CS/SHDN pin is used to initiate communication
with the device when pulled low and will end a conver-
sion and put the device in low power standby when
pulled high. The CS/SHDN pin must be pulled high
between conversions.
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
Name
PIN FUNCTION TABLE
Function
VDD
+2.7V to 5.5V Power Supply
Digital Ground
DGND
AGND
CH0-CH7
CLK
4.0
DEVICE OPERATION
Analog Ground
The MCP3204/3208 A/D converters employ a conven-
tional SAR architecture. With this architecture, a sam-
ple is acquired on an internal sample/hold capacitor for
1.5 clock cycles starting on the fourth rising edge of the
serial clock after the start bit has been received. Fol-
lowing this sample time, the device uses the collected
charge on the internal sample/hold capacitor to pro-
duce a serial 12-bit digital output code. Conversion
rates of 100 ksps are possible on the MCP3204/3208.
See Section 6.2, “Maintaining Minimum Clock Speed”,
for information on minimum clock rates. Communica-
tion with the device is accomplished using a 4-wire SPI-
compatible interface.
Analog Inputs
Serial Clock
DIN
Serial Data In
DOUT
Serial Data Out
CS/SHDN
VREF
Chip Select/Shutdown Input
Reference Voltage Input
3.1
DGND
Digital ground connection to internal digital circuitry.
3.2
AGND
4.1
Analog Inputs
Analog ground connection to internal analog circuitry.
The MCP3204/3208 devices offer the choice of using
the analog input channels configured as single-ended
inputs or pseudo-differential pairs. The MCP3204 can
be configured to provide two pseudo-differential input
pairs or four single-ended inputs, while the MCP3208
can be configured to provide four pseudo-differential
input pairs or eight single-ended inputs. Configuration
is done as part of the serial command before each con-
version begins. When used in the pseudo-differential
mode, each channel pair (i.e., CH0 and CH1, CH2 and
CH3 etc.) is programmed to be the IN+ and IN- inputs
as part of the command string transmitted to the
device. The IN+ input can range from IN- to (VREF + IN-
). The IN- input is limited to ±100 mV from the VSS rail.
The IN- input can be used to cancel small signal com-
mon-mode noise which is present on both the IN+ and
IN- inputs.
3.3
CH0 - CH7
Analog inputs for channels 0 - 7 for the multiplexed
inputs. Each pair of channels can be programmed to be
used as two independent channels in single-ended
mode or as a single pseudo-differential input, where
one channel is IN+ and one channel is IN. See
Section 4.1, “Analog Inputs”, and Section 5.0, “Serial
Communications”, for information on programming the
channel configuration.
3.4
Serial Clock (CLK)
The SPI clock pin is used to initiate a conversion and
clock out each bit of the conversion as it takes place.
See Section 6.2, “Maintaining Minimum Clock Speed”,
for constraints on clock speed.
When operating in the pseudo-differential mode, if the
voltage level of IN+ is equal to or less than IN-, the
resultant code will be 000h. If the voltage at IN+ is
equal to or greater than {[VREF + (IN-)] - 1 LSB}, then
the output code will be FFFh. If the voltage level at IN-
is more than 1 LSB below VSS, the voltage level at the
IN+ input will have to go below VSS to see the 000h
output code. Conversely, if IN- is more than 1 LSB
above VSS, then the FFFh code will not be seen unless
the IN+ input level goes above VREF level.
3.5
Serial Data Input (DIN)
The SPI port serial data input pin is used to load
channel configuration data into the device.
3.6
Serial Data Output (DOUT)
The SPI serial data output pin is used to shift out the
results of the A/D conversion. Data will always change
on the falling edge of each clock as the conversion
takes place.
For the A/D converter to meet specification, the charge
holding capacitor (CSAMPLE) must be given enough
time to acquire a 12-bit accurate voltage level during
the 1.5 clock cycle sampling period. The analog input
model is shown in Figure 4-1.
© 2007 Microchip Technology Inc.
DS21298D-page 13
MCP3204/3208
This diagram illustrates that the source impedance (RS)
adds to the internal sampling switch (RSS) impedance,
directly effecting the time that is required to charge the
capacitor (Csample). Consequently, larger source
impedances increase the offset, gain and integral
linearity errors of the conversion (see Figure 4-2).
EQUATION
Digital Output Code =
4096 × VIN
--------------------------
VREF
VIN = analog input voltage
REF = reference voltage
V
4.2
Reference Input
When using an external voltage reference device, the
system designer should always refer to the manufac-
turer’s recommendations for circuit layout. Any instabil-
ity in the operation of the reference device will have a
direct effect on the operation of the A/D converter.
For each device in the family, the reference input
(VREF) determines the analog input voltage range. As
the reference input is reduced, the LSB size is reduced
accordingly. The theoretical digital output code pro-
duced by the A/D converter is a function of the analog
input signal and the reference input, as shown below.
VDD
Sampling
Switch
VT = 0.6V
RS = 1 kΩ
CHx
RSS
SS
CSAMPLE
= DAC capacitance
= 20 pF
CPIN
7 pF
ILEAKAGE
VA
VT = 0.6V
±1 nA
VSS
Legend
VA
Signal Source
Leakage Current At The Pin
Due To Various Junctions
=
I
=
leakage
SS
Source Impedance
Input Channel Pad
Input Pin Capacitance
Threshold Voltage
Sampling switch
R
=
=
=
=
=
=
=
ss
CHx
Sampling switch resistor
Sample/hold capacitance
R
s
C
C
pin
sample
V
t
FIGURE 4-1:
Analog Input Model.
2.5
2.0
1.5
1.0
0.5
VDD = 5 V
VDD = 2.7 V
0.0
100
1000
10000
Input Resistance (Ohms)
FIGURE 4-2:
Maximum Clock Frequency
vs. Input resistance (RS) to maintain less than a
0.1 LSB deviation in INL from nominal
conditions.
DS21298D-page 14
© 2007 Microchip Technology Inc.
MCP3204/3208
TABLE 5-1:
CONFIGURATION BITS FOR
THE MCP3204
5.0
SERIAL COMMUNICATIONS
Communication with the MCP3204/3208 devices is
accomplished using a standard SPI-compatible serial
interface. Initiating communication with either device is
done by bringing the CS line low (see Figure 5-1). If the
device was powered up with the CS pin low, it must be
brought high and back low to initiate communication.
The first clock received with CS low and DIN high will
constitute a start bit. The SGL/DIFF bit follows the start
bit and will determine if the conversion will be done
using single-ended or differential input mode. The next
three bits (D0, D1 and D2) are used to select the input
channel configuration. Table 5-1 and Table 5-2 show
the configuration bits for the MCP3204 and MCP3208,
respectively. The device will begin to sample the ana-
log input on the fourth rising edge of the clock after the
start bit has been received. The sample period will end
on the falling edge of the fifth clock following the start
bit.
Control Bit
Selections
Input
Channel
Configuration Selection
Single/
D2* D1 D0
Diff
1
1
1
1
0
X
X
X
X
X
0
0
1
1
0
0
1
0
1
0
single-ended
single-ended
single-ended
single-ended
differential
CH0
CH1
CH2
CH3
CH0 = IN+
CH1 = IN-
0
0
0
X
X
X
0
1
1
1
0
1
differential
differential
differential
CH0 = IN-
CH1 = IN+
CH2 = IN+
CH3 = IN-
CH2 = IN-
CH3 = IN+
Once the D0 bit is input, one more clock is required to
complete the sample and hold period (DIN is a “don’t
care” for this clock). On the falling edge of the next
clock, the device will output a low null bit. The next 12
clocks will output the result of the conversion with MSB
first, as shown in Figure 5-1. Data is always output from
the device on the falling edge of the clock. If all 12 data
bits have been transmitted and the device continues to
receive clocks while the CS is held low, the device will
output the conversion result LSB first, as shown in
Figure 5-2. If more clocks are provided to the device
while CS is still low (after the LSB first data has been
transmitted), the device will clock out zeros indefinitely.
* D2 is a “don’t care” for MCP3204
TABLE 5-2:
CONFIGURATION BITS FOR
THE MCP3208
Control Bit
Selections
Input
Channel
Configuration Selection
Single
D2 D1 D0
/Diff
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
single-ended
single-ended
single-ended
single-ended
single-ended
single-ended
single-ended
single-ended
differential
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
If necessary, it is possible to bring CS low and clock in
leading zeros on the DIN line before the start bit. This is
often done when dealing with microcontroller-based
SPI ports that must send 8 bits at a time. Refer to
Section 6.1 for more details on using the MCP3204/
3208 devices with hardware SPI ports.
CH0 = IN+
CH1 = IN-
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
differential
differential
differential
differential
differential
differential
differential
CH0 = IN-
CH1 = IN+
CH2 = IN+
CH3 = IN-
CH2 = IN-
CH3 = IN+
CH4 = IN+
CH5 = IN-
CH4 = IN-
CH5 = IN+
CH6 = IN+
CH7 = IN-
CH6 = IN-
CH7 = IN+
© 2007 Microchip Technology Inc.
DS21298D-page 15
MCP3204/3208
t
t
CYC
CYC
t
CSH
CS
t
SUCS
CLK
SGL/
DIFF
SGL/
DIFF
D
Don’t Care
Start
Start
D2 D1 D0
D2
IN
HI-Z
HI-Z
Null
Bit
D
B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0*
OUT
t
CONV
t
t
**
SAMPLE
DATA
* After completing the data transfer, if further clocks are applied with CS low, the A/D converter will output LSB
first data, followed by zeros indefinitely (see Figure 5-2 below).
** tDATA: during this time, the bias current and the comparator power down while the reference input becomes
a high impedance node, leaving the CLK running to clock out the LSB-first data or zeros.
FIGURE 5-1:
Communication with the MCP3204 or MCP3208.
t
CYC
t
CSH
CS
t
SUCS
Power Down
CLK
Start
D
Don’t Care
D2 D1 D0
IN
SGL/
DIFF
HI-Z
*
Null
Bit
HI-Z
B11
B8 B7 B6 B5 B4 B3 B2 B1 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10B11
B10 B9
D
OUT
(MSB)
t
**
t
DATA
CONV
t
SAMPLE
* After completing the data transfer, if further clocks are applied with CS low, the A/D converter will output zeros
indefinitely.
** tDATA: During this time, the bias circuit and the comparator power down while the reference input becomes a
high impedance node, leaving the CLK running to clock out LSB first data or zeroes.
FIGURE 5-2:
Communication with MCP3204 or MCP3208 in LSB First Format.
DS21298D-page 16
© 2007 Microchip Technology Inc.
MCP3204/3208
6.0
6.1
APPLICATIONS INFORMATION
Using the MCP3204/3208 with
Microcontroller (MCU) SPI Ports
With most microcontroller SPI ports, it is required to
send groups of eight bits. It is also required that the
microcontroller SPI port be configured to clock out data
on the falling edge of clock and latch data in on the ris-
ing edge. Because communication with the MCP3204/
3208 devices may not need multiples of eight clocks, it
will be necessary to provide more clocks than are
required. This is usually done by sending ‘leading
zeros’ before the start bit. As an example, Figure 6-1
and Figure 6-2 illustrate how the MCP3204/3208 can
be interfaced to a MCU with a hardware SPI port.
Figure 6-1 depicts the operation shown in SPI Mode
0,0, which requires that the SCLK from the MCU idles
in the ‘low’ state, while Figure 6-2 shows the similar
case of SPI Mode 1,1, where the clock idles in the ‘high’
state.
As is shown in Figure 6-1, the first byte transmitted to
the A/D converter contains five leading zeros before
the start bit. Arranging the leading zeros this way
allows the output 12 bits to fall in positions easily
manipulated by the MCU. The MSB is clocked out of
the A/D converter on the falling edge of clock number
12. Once the second eight clocks have been sent to the
device, the MCU’s receive buffer will contain three
unknown bits (the output is at high impedance for the
first two clocks), the null bit and the highest order four
bits of the conversion. Once the third byte has been
sent to the device, the receive register will contain the
lowest order eight bits of the conversion results.
Employing this method ensures simpler manipulation
of the converted data.
Figure 6-2 shows the same thing in SPI Mode 1,1,
which requires that the clock idles in the high state. As
with mode 0,0, the A/D converter outputs data on the
falling edge of the clock and the MCU latches data from
the A/D converter in on the rising edge of the clock.
© 2007 Microchip Technology Inc.
DS21298D-page 17
MCP3204/3208
CS
MCU latches data from A/D
converter on rising edges of SCLK
SCLK
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Data is clocked out of A/D
converter on falling edges
SGL/
D2
DO
D1
Don’tCare
DIN
DIFF
Start
NULL
BIT
HI-Z
B7
B6 B5 B4 B3 B2 B1 B0
B11 B10 B9 B8
DOUT
Start
Bit
MCU Transmitted Data
(Aligned with falling
edge of clock)
SGL/
0
0
0
0
0
1
D1 DO
X X
X
X
X X X
D2
X X
X
DIFF
MCU Received Data
(Aligned with rising
edge of clock)
0
?
?
(Null)
B11 B10 B9 B8
B7 B6 B5 B4 B3 B2 B1 B0
?
?
?
?
?
?
?
?
?
Data stored into MCU receive
register after transmission of first
8 bits
Data stored into MCU receive
register after transmission of
second 8 bits
Data stored into MCU receive
register after transmission of last
8 bits
X = “Don’t Care” Bits
FIGURE 6-1:
SPI Communication using 8-bit segments (Mode 0,0: SCLK idles low).
CS
MCU latches data from A/D converter
on rising edges of SCLK
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
16
17 18 19 20 21 22 23 24
SCLK
DIN
Data is clocked out of A/D
converter on falling edges
SGL/
DIFF
Don’t Care
D2
D1 DO
Start
HI-Z
NULL
BIT
B11 B10 B9
B8
B7 B6 B5 B4 B3 B2 B1 B0
D
OUT
Start
Bit
MCU Transmitted Data
(Aligned with falling
edge of clock)
SGL/
DIFF
0
0
0
0
0
1
D2
D1 DO
X
X
0
X
X
X
X
X
X
X
X
X
X
X
X
MCU Received Data
(Aligned with rising
edge of clock)
?
?
?
?
?
?
?
?
?
?
?
B11 B10 B9 B8
B7 B6 B5 B4 B3 B2 B1 B0
(Null)
Data stored into MCU receive
register after transmission of first
8 bits
Data stored into MCU receive
register after transmission of
second 8 bits
Data stored into MCU receive
register after transmission of last
8 bits
X = “Don’t Care” Bits
FIGURE 6-2:
SPI Communication using 8-bit segments (Mode 1,1: SCLK idles high).
DS21298D-page 18
© 2007 Microchip Technology Inc.
MCP3204/3208
6.2
Maintaining Minimum Clock
Speed
6.3
Buffering/Filtering the Analog
Inputs
When the MCP3204/3208 initiates the sample period,
charge is stored on the sample capacitor. When the
sample period is complete, the device converts one bit
for each clock that is received. It is important for the
user to note that a slow clock rate will allow charge to
bleed off the sample capacitor while the conversion is
taking place. At 85°C (worst case condition), the part
will maintain proper charge on the sample capacitor for
at least 1.2 ms after the sample period has ended. This
means that the time between the end of the sample
period and the time that all 12 data bits have been
clocked out must not exceed 1.2 ms (effective clock
frequency of 10 kHz). Failure to meet this criterion may
introduce linearity errors into the conversion outside
the rated specifications. It should be noted that during
the entire conversion cycle, the A/D converter does not
require a constant clock speed or duty cycle, as long as
all timing specifications are met.
If the signal source for the A/D converter is not a low
impedance source, it will have to be buffered or inaccu-
rate conversion results may occur (see Figure 4-2). It is
also recommended that a filter be used to eliminate any
signals that may be aliased back into the conversion
results, as is illustrated in Figure 6-3, where an op amp
is used to drive the analog input of the MCP3204/3208.
This amplifier provides a low impedance source for the
converter input, and a low pass filter, which eliminates
unwanted high frequency noise.
Low pass (anti-aliasing) filters can be designed using
Microchip’s free interactive FilterLab™ software. Filter-
Lab will calculate capacitor and resistor values, as well
as determine the number of poles that are required for
the application. For more information on filtering sig-
nals, see AN699, “Anti-Aliasing Analog Filters for Data
Acquisition Systems”.
VDD
10 µF
4.096V
Reference
0.1 µF
1 µF
MCP1541
1 µF
IN+
IN-
VREF
MCP3204
C1
R2
MCP601
R1
VIN
+
-
C2
R4
R3
FIGURE 6-3:
The MCP601 Operational Amplifier is used to implement a second order anti-aliasing
filter for the signal being converted by the MCP3204.
© 2007 Microchip Technology Inc.
DS21298D-page 19
MCP3204/3208
6.4
Layout Considerations
6.5
Utilizing the Digital and Analog
Ground Pins
When laying out a printed circuit board for use with
analog components, care should be taken to reduce
noise wherever possible. A bypass capacitor should
always be used with this device, placed as close as
possible to the device pin. A bypass capacitor value of
1 µF is recommended.
The MCP3204/3208 devices provide both digital and
analog ground connections to provide another means
of noise reduction. As shown in Figure 6-5, the analog
and digital circuitry is separated internal to the device.
This reduces noise from the digital portion of the device
being coupled into the analog portion of the device. The
two grounds are connected internally through the sub-
strate, which has a resistance of 5 -10Ω.
Digital and analog traces should be separated as much
as possible on the board, with no traces running under-
neath the device or the bypass capacitor. Extra precau-
tions should be taken to keep traces with high
frequency signals (such as clock lines) as far as
possible from analog traces.
If no ground plane is utilized, then both grounds must
be connected to VSS on the board. If a ground plane is
available, both digital and analog ground pins should
be connected to the analog ground plane. If both an
analog and a digital ground plane are available, both
the digital and the analog ground pins should be con-
nected to the analog ground plane. Following these
steps will reduce the amount of digital noise from the
rest of the board being coupled into the A/D converter.
Use of an analog ground plane is recommended in
order to keep the ground potential the same for all
devices on the board. Providing VDD connections to
devices in a “star” configuration can also reduce noise
by eliminating return current paths and associated
errors (see Figure 6-4). For more information on layout
tips when using A/D converters, refer to AN688,
“Layout Tips for 12-Bit A/D converter Applications”.
VDD
VDD
MCP3204/08
Connection
Digital Side
Analog Side
-SPI Interface
-Shift Register
-Control Logic
-Sample Cap
-Capacitor Array
-Comparator
Substrate
5 - 10Ω
Device 4
Device 1
DGND
AGND
0.1 µF
Device 3
Analog Ground Plane
Device 2
FIGURE 6-5:
Separation of Analog and
Digital Ground Pins.
FIGURE 6-4:
VDD traces arranged in a
‘Star’ configuration in order to reduce errors
caused by current return paths.
DS21298D-page 20
© 2007 Microchip Technology Inc.
MCP3204/3208
7.0
7.1
PACKAGING INFORMATION
Package Marking Information
14-Lead PDIP (300 mil)
Example:
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
MCP3204-B
e
3
I/P
YYWWNNN
0723NNN
14-Lead SOIC (150 mil)
Example:
e
3
MCP3204-B
XXXXXXXXXXX
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
0723NNN
14-Lead TSSOP (4.4mm) *
Example:
XXXXXXXX
YYWW
3204-C
e3
0723
NNN
NNN
Legend: XX...X Customer-specific information
Y
YY
WW
NNN
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
*
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
)
e3
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2007 Microchip Technology Inc.
DS21298D-page 21
MCP3204/3208
Package Marking Information (Continued)
16-Lead PDIP (300 mil) (MCP3304)
Example:
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
MCP3208-B e
3
I/P
YYWWNNN
0723NNN
16-Lead SOIC (150 mil) (MCP3304)
Example:
e
3
MCP3208-B
XXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
YYWWNNN
IYWWNNN
DS21298D-page 22
© 2007 Microchip Technology Inc.
MCP3204/3208
14-Lead Plastic Dual In-Line (P) – 300 mil Body [PDIP]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
N
NOTE 1
E1
3
1
2
D
E
A2
A
L
c
A1
b1
b
e
eB
Units
INCHES
NOM
14
Dimension Limits
MIN
MAX
Number of Pins
Pitch
N
e
.100 BSC
–
Top to Seating Plane
A
–
.210
.195
–
Molded Package Thickness
Base to Seating Plane
Shoulder to Shoulder Width
Molded Package Width
Overall Length
A2
A1
E
.115
.015
.290
.240
.735
.115
.008
.045
.014
–
.130
–
.310
.250
.750
.130
.010
.060
.018
–
.325
.280
.775
.150
.015
.070
.022
.430
E1
D
Tip to Seating Plane
Lead Thickness
L
c
Upper Lead Width
b1
b
Lower Lead Width
Overall Row Spacing §
eB
Notes:
1. Pin 1 visual index feature may vary, but must be located with the hatched area.
2. § Significant Characteristic.
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-005B
© 2007 Microchip Technology Inc.
DS21298D-page 23
MCP3204/3208
14-Lead Plastic Small Outline (SL) – Narrow, 3.90 mm Body [SOIC]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
N
E
E1
NOTE 1
1
2
3
e
h
b
α
h
c
φ
A2
A
L
A1
β
L1
Units
MILLMETERS
Dimension Limits
MIN
NOM
MAX
Number of Pins
Pitch
N
e
14
1.27 BSC
Overall Height
A
–
–
1.75
–
Molded Package Thickness
Standoff §
A2
A1
E
1.25
0.10
–
–
0.25
Overall Width
6.00 BSC
Molded Package Width
Overall Length
E1
D
h
3.90 BSC
8.65 BSC
Chamfer (optional)
Foot Length
0.25
0.40
–
0.50
1.27
L
–
Footprint
L1
φ
1.04 REF
Foot Angle
0°
0.17
0.31
5°
–
–
–
–
–
8°
Lead Thickness
Lead Width
c
0.25
0.51
15°
b
Mold Draft Angle Top
Mold Draft Angle Bottom
α
β
5°
15°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic.
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-065B
DS21298D-page 24
© 2007 Microchip Technology Inc.
MCP3204/3208
14-Lead Plastic Thin Shrink Small Outline (ST) – 4.4 mm Body [TSSOP]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
N
E
E1
NOTE 1
1
2
e
b
c
φ
A2
A
A1
L
L1
Units
MILLIMETERS
Dimension Limits
MIN
NOM
MAX
Number of Pins
Pitch
N
e
14
0.65 BSC
Overall Height
Molded Package Thickness
Standoff
A
–
–
1.20
1.05
0.15
A2
A1
E
0.80
0.05
1.00
–
Overall Width
Molded Package Width
Molded Package Length
Foot Length
6.40 BSC
E1
D
4.30
4.90
0.45
4.40
4.50
5.10
0.75
5.00
L
0.60
Footprint
L1
φ
1.00 REF
Foot Angle
0°
–
–
–
8°
Lead Thickness
Lead Width
c
0.09
0.19
0.20
0.30
b
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side.
3. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-087B
© 2007 Microchip Technology Inc.
DS21298D-page 25
MCP3204/3208
16-Lead Plastic Dual In-Line (P) – 300 mil Body [PDIP]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
N
NOTE 1
E1
1
2
3
D
E
A
A2
L
c
A1
b1
e
eB
b
Units
INCHES
NOM
16
Dimension Limits
MIN
MAX
Number of Pins
Pitch
N
e
.100 BSC
–
Top to Seating Plane
A
–
.210
.195
–
Molded Package Thickness
Base to Seating Plane
Shoulder to Shoulder Width
Molded Package Width
Overall Length
A2
A1
E
.115
.015
.290
.240
.735
.115
.008
.045
.014
–
.130
–
.310
.250
.755
.130
.010
.060
.018
–
.325
.280
.775
.150
.015
.070
.022
.430
E1
D
Tip to Seating Plane
Lead Thickness
L
c
Upper Lead Width
b1
b
Lower Lead Width
Overall Row Spacing §
eB
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic.
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-017B
DS21298D-page 26
© 2007 Microchip Technology Inc.
MCP3204/3208
16-Lead Plastic Small Outline (SL) – Narrow, 3.90 mm Body [SOIC]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
N
E
E1
NOTE 1
3
1
2
e
b
h
α
h
c
φ
A2
A
L
β
A1
L1
Units
MILLMETERS
Dimension Limits
MIN
NOM
MAX
Number of Pins
Pitch
N
e
16
1.27 BSC
Overall Height
A
–
–
1.75
–
Molded Package Thickness
Standoff §
A2
A1
E
1.25
0.10
–
–
0.25
Overall Width
6.00 BSC
Molded Package Width
Overall Length
E1
D
h
3.90 BSC
9.90 BSC
Chamfer (optional)
Foot Length
0.25
0.40
–
0.50
1.27
L
–
Footprint
L1
φ
1.04 REF
Foot Angle
0°
0.17
0.31
5°
–
–
–
–
–
8°
Lead Thickness
Lead Width
c
0.25
0.51
15°
b
Mold Draft Angle Top
Mold Draft Angle Bottom
α
β
5°
15°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic.
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-108B
© 2007 Microchip Technology Inc.
DS21298D-page 27
MCP3204/3208
NOTES:
DS21298D-page 28
© 2007 Microchip Technology Inc.
MCP3204/3208
APPENDIX A: REVISION HISTORY
Revision D (January 2007)
This revision includes updates to the packaging dia-
grams.
© 2007 Microchip Technology Inc.
DS21298D-page 29
MCP3204/3208
NOTES:
DS21298D-page 30
© 2007 Microchip Technology Inc.
MCP3204/3208
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
X
/XX
Examples:
a)
b)
c)
MCP3204-BI/P: ±1 LSB INL, Industrial Tem-
perature, PDIP package.
Grade Temperature Package
Range
MCP3204-BI/SL: ±1 LSB INL, Industrial
Temperature, SOIC package.
Device:
MCP3204: 4-Channel 12-Bit Serial A/D Converter
MCP3204T: 4-Channel 12-Bit Serial A/D Converter
(Tape and Reel)
MCP3204-CI/ST: ±2 LSB INL, Industrial
Temperature, TSSOP package.
MCP3208: 8-Channel 12-Bit Serial A/D Converter
MCP3208T: 8-Channel 12-Bit Serial A/D Converter
(Tape and Reel)
a)
b)
c)
MCP3208-BI/P: ±1 LSB INL, Industrial
Temperature, PDIP package.
MCP3208-BI/SL: ±1 LSB INL, Industrial
Temperature, SOIC package.
Grade:
B
C
=
=
±1 LSB INL
±2 LSB INL
MCP3208-CI/ST: ±2 LSB INL, Industrial
Temperature, TSSOP package.
Temperature Range:
Package:
I
=
-40°C to +85°C
P
SL
ST
=
=
=
Plastic DIP (300 mil Body), 14-lead, 16-lead
Plastic SOIC (150 mil Body), 14-lead, 16-lead
Plastic TSSOP (4.4mm), 14-lead
© 2007 Microchip Technology Inc.
DS21298D-page31
MCP3204/3208
NOTES:
DS21298D-page 32
© 2007 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART,
PRO MATE, PowerSmart, rfPIC, and SmartShunt are
registered trademarks of Microchip Technology Incorporated
in the U.S.A. and other countries.
AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,
ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,
In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active
Thermistor, Mindi, MiWi, MPASM, MPLIB, MPLINK, PICkit,
PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,
PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB,
rfPICDEM, Select Mode, Smart Serial, SmartTel, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2007, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona, Gresham, Oregon and Mountain View, California. The
Company’s quality system processes and procedures are for its PIC®
MCUs and dsPIC DSCs, KEELOQ® code hopping devices, Serial
EEPROMs, microperipherals, nonvolatile memory and analog
products. In addition, Microchip’s quality system for the design and
manufacture of development systems is ISO 9001:2000 certified.
© 2007 Microchip Technology Inc.
DS21298D-page 33
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Habour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Korea - Gumi
Tel: 82-54-473-4301
Fax: 82-54-473-4302
Boston
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Seoul
China - Fuzhou
Tel: 86-591-8750-3506
Fax: 86-591-8750-3521
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Penang
Tel: 60-4-646-8870
Fax: 60-4-646-5086
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Shunde
Tel: 86-757-2839-5507
Fax: 86-757-2839-5571
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
China - Xian
Tel: 86-29-8833-7250
Fax: 86-29-8833-7256
12/08/06
DS21298D-page 34
© 2007 Microchip Technology Inc.
相关型号:
MCP3208-BI/SLG
8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16, 3.90 MM, PLASTIC, SOIC-16
MICROCHIP
MCP3208-BI/SN
8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16, 0.150 INCH, SO-16
MICROCHIP
©2020 ICPDF网 联系我们和版权申明