MCP6032-E/SL [MICROCHIP]
0.9 μA, High Precision Op Amps; 0.9 μA ,高精度运算放大器型号: | MCP6032-E/SL |
厂家: | MICROCHIP |
描述: | 0.9 μA, High Precision Op Amps |
文件: | 总34页 (文件大小:636K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCP6031/2/3/4
0.9 µA, High Precision Op Amps
Features
Description
• Rail-to-Rail Input and Output
The Microchip Technology Inc. MCP6031/2/3/4 family
of operational amplifiers (op amps) operate with a
single supply voltage as low as 1.8V, while drawing
ultra low quiescent current per amplifier (0.9 µA,
typical). This family also has low input offset voltage
(±150 µV, maximum) and rail-to-rail input and output
operation. This combination of features supports
battery-powered and portable applications.
• Low Offset Voltage: ±150 µV (maximum)
• Ultra Low Quiescent Current: 0.9 µA (typical)
• Wide Power Supply Voltage: 1.8V to 5.5V
• Gain Bandwidth Product: 10 kHz (typical)
• Unity Gain Stable
• Chip Select (CS) capability: MCP6033
• Extended Temperature Range:
- -40°C to +125°C
The MCP6031/2/3/4 family is unity gain stable and has
a gain bandwidth product of 10 kHz (typical). These
specs make these op amps appropriate for low fre-
quency applications, such as battery current
monitoring and sensor conditioning.
• No Phase Reversal
Applications
The MCP6031/2/3/4 family is offered in single
(MCP6031), single with power saving Chip Select (CS)
input (MCP6033), dual (MCP6032), and quad
(MCP6034) configurations.
• Toll Booth Tags
• Wearable Products
• Battery Current Monitoring
• Sensor Conditioning
• Battery Powered
The MCP6031/2/3/4 family is designed with Micro-
chip’s advanced CMOS process. All devices are
available in the extended temperature range, with a
power supply range of 1.8V to 5.5V.
Design Aids
• SPICE Macro Models
• FilterLab® Software
• Mindi™ Circuit Designer & Simulator
• MAPS (Microchip Advanced Part Selector)
• Analog Demonstration and Evaluation Boards
• Application Notes
Package Types
MCP6031
DFN, SOIC, MSOP
MCP6033
DFN, SOIC, MSOP
NC
NC
NC
CS
1
2
8
7
1
2
8
7
VIN
–
+
VDD
VIN
–
+
VDD
VIN
VOUT
NC
VIN
VOUT
NC
3
4
6
5
3
4
6
5
VSS
VSS
Typical Application
MCP6031
SOT-23-5
MCP6034
SOIC, TSSOP
IDD
VDD
1.4V
to
5.5V
VOUTD
1
2
3
4
5
6
7
14
13
12
11
10
9
VOUTA
VOUT
VSS
1
5
4
VDD
10Ω
VOUT
VIND
VIND
VSS
–
VINA
–
+
2
3
MCP6031
1 MΩ
+
VINA
VIN
+
VIN–
100 kΩ
VDD
VINB
VINB
MCP6032
SOIC, MSOP
VINC
+
–
+
–
VINC
VDD
1
2
3
4
8
7
6
5
VOUTA
VDD – VOUT
IDD = -----------------------------------------
(10 V/V) ⋅ (10Ω)
VOUTC
8
VOUTB
VOUTB
VINA
–
+
VINB
VINB
–
+
VINA
High Side Battery Current Sensor
VSS
© 2008 Microchip Technology Inc.
DS22041B-page 1
MCP6031/2/3/4
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at those or any other conditions
above those indicated in the operational listings of this
specification is not implied. Exposure to maximum rat-
ing conditions for extended periods may affect device
reliability.
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
VDD – VSS ........................................................................7.0V
Current at Input Pins .....................................................±2 mA
Analog Inputs (VIN+, VIN-)†† .......... VSS – 1.0V to VDD + 1.0V
All Other Inputs and Outputs ......... VSS – 0.3V to VDD + 0.3V
†† See 4.1.2 “Input Voltage And Current Limits”
Difference Input Voltage ...................................... |VDD – VSS
|
Output Short-Circuit Current .................................continuous
Current at Output and Supply Pins ............................±30 mA
Storage Temperature.....................................-65°C to +150°C
Maximum Junction Temperature (TJ)..........................+150°C
ESD protection on all pins (HBM; MM) ................ ≥ 4 kV; 400V
DC ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS=GND, TA= +25°C, VCM = VDD/2,
VOUT ≈ VDD/2, VL = VDD/2, RL = 1 MΩ to VL and CS is tied low. (Refer to Figure 1-2 and Figure 1-3).
Parameters
Input Offset
Input Offset Voltage
Sym
Min
Typ
Max
Units
Conditions
VOS
-150
—
—
+150
—
µV
VDD = 3.0V, VCM = VDD/3
Input Offset Drift with Temperature ΔVOS/ΔTA
±3.0
µV/°C TA= -40°C to +125°C,
VDD = 3.0V, VCM = VDD/3
Power Supply Rejection Ratio
Input Bias Current and Impedance
Input Bias Current
PSRR
70
88
—
dB
VCM = VSS
IB
IB
—
—
—
—
—
—
±1.0
60
100
—
pA
pA
TA = +85°C
IB
2000
±1.0
1013||6
1013||6
5000
—
pA
TA = +125°C
Input Offset Current
IOS
ZCM
ZDIFF
pA
Common Mode Input Impedance
Differential Input Impedance
Common Mode
—
Ω||pF
Ω||pF
—
Common Mode Input Voltage
Range
VCMR
VSS − 0.3
—
95
93
89
93
VDD + 0.3
V
Common Mode Rejection Ratio
CMRR
70
72
70
72
—
—
—
—
dB
dB
dB
dB
VCM = -0.3V to 2.1V,
VDD = 1.8V
VCM = -0.3V to 5.8V,
VDD = 5.5V
VCM = 2.75V to 5.8V,
VDD = 5.5V
VCM = -0.3V to 2.75V,
VDD = 5.5V
Open-Loop Gain
DC Open-Loop Gain
(Large Signal)
AOL
95
115
—
dB
0.2V < VOUT < (VDD – 0.2V)
RL = 50 kΩ to VL
DS22041B-page 2
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
DC ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS=GND, TA= +25°C, VCM = VDD/2,
VOUT ≈ VDD/2, VL = VDD/2, RL = 1 MΩ to VL and CS is tied low. (Refer to Figure 1-2 and Figure 1-3).
Parameters
Sym
Min
Typ
Max
Units
Conditions
Output
Maximum Output Voltage Swing
VOL, VOH VSS + 10
—
VDD – 10
mV RL = 50 kΩ to VL,
0.5V input overdrive
Output Short-Circuit Current
ISC
—
—
±5
—
—
mA VDD = 1.8V
±23
mA
VDD = 5.5V
Power Supply
Supply Voltage
VDD
IQ
1.8
0.4
—
5.5
V
Quiescent Current per Amplifier
0.9
1.35
µA
IO = 0, VCM = VDD,
VDD = 5.5V
AC ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +1.8 to +5.5V, VSS = GND, VCM = VDD/2,
VOUT ≈ VDD/2, VL = VDD/2, CL = 60 pF, RL = 1 MΩ to VL and CS is tied low. (Refer to Figure 1-2 and Figure 1-3).
Parameters
Sym
Min
Typ
Max
Units
Conditions
AC Response
Gain Bandwidth Product
Phase Margin
GBWP
PM
—
—
—
10
65
—
—
—
kHz
°
G = +1 V/V
Slew Rate
SR
4.0
V/ms
Noise
Input Noise Voltage
Input Noise Voltage Density
Input Noise Current Density
Eni
eni
ini
—
—
—
3.9
165
0.6
—
—
—
µVp-p f = 0.1 Hz to 10 Hz
nV/√Hz f = 1 kHz
fA/√Hz f = 1 kHz
© 2008 Microchip Technology Inc.
DS22041B-page 3
MCP6031/2/3/4
MCP6033 CHIP SELECT ELECTRICAL CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, VDD = +1.8V to +5.5V, VSS =GND, TA = +25°C, VCM = VDD/2,
VOUT = VDD/2, VL = VDD/2, CL = 60 pF, RL = 1 MΩ to VL and CS is tied low (Refer to Figure 1-1).
Parameters
Sym
Min
Typ
Max
Units
Conditions
CS Low Specifications
CS Logic Threshold, Low
CS Input Current, Low
CS High Specifications
CS Logic Threshold, High
CS Input Current, High
GND Current
VIL
VSS
—
—
0.2VDD
—
V
ICSL
-10
pA
CS = VSS
VIH
ICSH
0.8VDD
—
VDD
—
V
10
-400
10
pA
pA
pA
CS = VDD
CS = VDD
CS = VDD
ISS
—
—
Amplifier Output Leakage
CS Dynamic Specifications
IO(LEAK)
—
—
CS Low to Amplifier Output
Turn-on Time
tON
—
—
—
4
10
100
—
ms
µs
V
CS ≤ 0.2VDD to VOUT = 0.9VDD/2,
G = +1 V/V, VIN = VDD/2,
RL = 50 kΩ to VL = VSS.
CS High to Amplifier Output
High-Z
tOFF
CS ≥ 0.8VDD to VOUT = 0.1VDD/2,
G = +1 V/V, VIN = VDD/2,
RL = 50 kΩ to VL = VSS.
CS Hysteresis
VHYST
0.3VDD
—
CS
VIL
VIH
tON
tOFF
VOUT
High-Z
High-Z
-0.9 µA
(typical)
-400 pA
(typical)
-400 pA
(typical)
ISS
ICS
10 pA
(typical)
FIGURE 1-1:
Timing Diagram for the CS
Pin on the MCP6033.
DS22041B-page 4
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
TEMPERATURE SPECIFICATIONS
Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +5.5V and VSS = GND.
Parameters
Temperature Ranges
Sym
Min
Typ
Max
Units
Conditions
Operating Temperature Range
Storage Temperature Range
TA
TA
-40
-65
—
—
+125
+150
°C
°C
Note
Thermal Package Resistances
Thermal Resistance, 5L-SOT-23
Thermal Resistance, 8L-DFN (2x3)
Thermal Resistance, 8L-SOIC
Thermal Resistance, 8L-MSOP
Thermal Resistance, 14L-SOIC
Thermal Resistance, 14L-TSSOP
θJA
θJA
θJA
θJA
θJA
θJA
—
—
—
—
—
—
256
84
—
—
—
—
—
—
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
163
206
120
100
Note:
The internal junction temperature (TJ) must not exceed the absolute maximum specification of +150°C.
1.1
Test Circuits
The test circuits used for the DC and AC tests are
shown in Figure 1-2 and Figure 1-3. The bypass
capacitors are laid out according to the rules discussed
in Section 4.6 “Supply Bypass”.
VDD
2.2 µF
VIN
0.1 µF
MCP603X
VOUT
RL
RN
CL
VDD/2
VL
RG
RF
FIGURE 1-2:
AC and DC Test Circuit for
Most Non-Inverting Gain Conditions.
VDD
2.2 µF
VDD/2
0.1 µF
MCP603X
VOUT
RL
RN
CL
VIN
VL
RG
FIGURE 1-3:
RF
AC and DC Test Circuit for
Most Inverting Gain Conditions.
© 2008 Microchip Technology Inc.
DS22041B-page 5
MCP6031/2/3/4
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL , CL = 60 pF and CS is tied low.
400
14%
640 Samples
TA = -40°C
300
200
100
0
VDD = 3.0V
12%
10%
8%
TA = +25°C
TA = +85°C
TA = +125°C
VCM = VDD/3
6%
-100
-200
-300
-400
4%
2%
VDD = 5.5V
0%
-150 -120 -90 -60 -30
0
30 60 90 120 150
Input Offset Voltage (μV)
Common Mode Input Voltage (V)
FIGURE 2-1:
Input Offset Voltage with
FIGURE 2-4:
Input Offset Voltage vs.
V
= 3.0V.
Common Mode Input Voltage with V = 5.5V.
DD
DD
400
22%
TA = -40°C
20%
18%
16%
14%
12%
10%
8%
6%
4%
2%
0%
640 Samples
DD = 3.0V
VCM = VDD/3
A = -40°C to +85°C
300
200
100
0
TA = +25°C
TA = +85°C
TA = +125°C
V
T
-100
-200
-300
-400
VDD = 1.8V
-20 -16 -12 -8 -4
0
4
8
12 16 20
Common Mode Input Voltage (V)
Input Offset Drift with Temperature (μV/°C)
FIGURE 2-2:
Input Offset Voltage Drift
FIGURE 2-5:
Input Offset Voltage vs.
with V = 3.0V and T ≤ +85°C.
Common Mode Input Voltage with V = 1.8V.
DD
A
DD
14%
12%
10%
8%
250
200
150
640 Samples
VDD = 3.0V
VCM = VDD/3
100
50
T
A = +85°C to +125°C
VDD = 3.0V
VDD = 5.5V
0
6%
-50
4%
VDD = 1.8V
-100
-150
-200
-250
2%
0%
-30 -24 -18 -12 -6
0
6
12 18 24 30
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Output Voltage (V)
Input Offset Drift with Temperature (μV/°C)
FIGURE 2-3:
Input Offset Voltage Drift
FIGURE 2-6:
Input Offset Voltage vs.
with V = 3.0V and T ≥ +85°C.
Output Voltage.
DD
A
DS22041B-page 6
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL, CL = 60 pF and CS is tied low.
1,000
110
CMRR (VDD = 1.8V,
105
100
95
90
85
80
75
70
65
60
CMRR (VDD = 5.5V,
VCM = -0.3V to 5.8V)
VCM = -0.3V to 2.1V)
PSRR (VDD = 1.8V to 5.5V, VCM = VSS
)
100
0.1
1
10
100
1k
10k
100k
1E-1 1E+0 1E+1 1E+2 1E+3 1E+4 1E+5
-50
-25
0
25
50
75
100
125
Frequency (Hz)
Ambient Temperature (°C)
FIGURE 2-7:
Input Noise Voltage Density
FIGURE 2-10:
Common Mode Rejection
vs. Frequency.
Ratio, Power Supply Rejection Ratio vs. Ambient
Temperature.
200
175
150
125
100
75
10000
VDD = 5.5V
VCM = VDD
1000
Input Bias Current
100
50
10
f = 1 kHz
DD = 5.5V
25
0
V
Input Offset Current
1
25
45
65
85
105
125
Common Mode Input Voltage (V)
Ambient Temperature (°C)
FIGURE 2-8:
Input Noise Voltage Density
FIGURE 2-11:
Input Bias, Offset Currents
vs. Common Mode Input Voltage.
vs. Ambient Temperature.
100
10000
PSRR-
90
VDD = 5.5V
80
70
PSRR+
TA = +125°C
1000
100
10
60
CMRR
50
40
30
20
TA = +85°C
10
0
VDD = 5.5V
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Common Mode Input Voltage (V)
0.1
1
10
100
1000
Frequency (Hz)
FIGURE 2-9:
Common Mode Rejection
FIGURE 2-12:
Input Bias Current vs.
Ratio, Power Supply Rejection Ratio vs.
Frequency.
Common Mode Input Voltage.
© 2008 Microchip Technology Inc.
DS22041B-page 7
MCP6031/2/3/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL, CL = 60 pF and CS is tied low.
120
100
80
60
40
20
0
0
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Open-Loop Gain
VDD = 5.5V @ VCM = VDD
VDD = 1.8V @ VCM = VDD
-30
-60
Open-Loop Phase
-90
-120
-150
-180
-210
VDD = 5.5V @ VCM = VSS
VDD = 1.8V @ VCM = VSS
VDD = 5.5V
-20
0.001 0.01
1k 10k 100k
10 100
0.1
1
-50
-25
0
25
50
75
100 125
Ambient Temperature (°C)
Frequency (Hz)
FIGURE 2-13:
Quiescent Current vs
FIGURE 2-16:
Open-Loop Gain, Phase vs.
Ambient Temperature.
Frequency.
1.2
130
125
120
115
110
105
100
95
VCM = VDD
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
TA = +125°C
TA = +85°C
TA = +25°C
TA = -40°C
RL = 50 kΩ
VSS + 0.2V < VOUT < VDD - 0.2V
90
85
80
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Power Supply Voltage VDD (V)
Power Supply Voltage (V)
FIGURE 2-14:
Quiescent Current vs.
FIGURE 2-17:
DC Open-Loop Gain vs.
Power Supply Voltage with V
= V
.
Power Supply Voltage.
CM
DD
1.2
1.1
130
VCM = VSS
125
120
115
110
105
100
95
90
85
80
VDD = 5.5V
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
VDD = 1.8V
TA = +125°C
TA = +85°C
TA = +25°C
TA = -40°C
RL = 50 kΩ
Large Signal AOL
0.00
0.05
0.10
0.15
0.20
0.25
Output Voltage Headroom
VDD - VOUT or VOUT - VSS (V)
Power Supply Voltage (V)
FIGURE 2-15:
Quiescent Current vs.
FIGURE 2-18:
DC Open-Loop Gain vs.
Power Supply Voltage with V
= V
.
Output Voltage Headroom.
CM
SS
DS22041B-page 8
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL, CL = 60 pF and CS is tied low.
130
20
18
16
14
12
10
8
6
4
2
0
90
80
70
60
50
40
30
20
10
0
120
110
100
90
Phase Margin
Gain Bandwidth Product
80
VDD = 1.8V
G = +1 V/V
70
Input Referred
60
100
1,000
10,000
-50 -25
0
25
50
75 100 125
Frequency (Hz)
Ambient Temperature (°C)
FIGURE 2-19:
Channel-to-Channel
FIGURE 2-22:
Gain Bandwidth Product,
Separation vs. Frequency ( MCP6032/4 only).
Phase Margin vs. Ambient Temperature.
20
18
16
14
12
10
8
6
4
2
180
160
140
120
100
80
35
30
Gain Bandwidth Product
TA = -40°C
TA = +25°C
TA = +85°C
TA = +125°C
25
20
15
10
5
Phase Margin
60
40
VDD = 5.5V
G = +1 V/V
20
0
0
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Power Supply Voltage (V)
Common Mode Input Voltage (V)
FIGURE 2-20:
Gain Bandwidth Product,
FIGURE 2-23:
Ouput Short Circuit Current
Phase Margin vs. Common Mode Input Voltage.
vs. Power Supply Voltage.
10
20
18
16
14
12
10
8
6
4
2
0
90
80
70
60
50
40
30
20
10
0
VDD = 5.5V
VDD = 3.0V
VDD = 1.8V
Phase Margin
1
Gain Bandwidth Product
VDD = 5.5V
G = +1 V/V
0.1
1K
10K
10
100
-50 -25
0
25
50
75 100 125
Ambient Temperature (°C)
Frequency (Hz)
FIGURE 2-21:
Gain Bandwidth Product,
FIGURE 2-24:
Output Voltage Swing vs.
Phase Margin vs. Ambient Temperature.
Frequency.
© 2008 Microchip Technology Inc.
DS22041B-page 9
MCP6031/2/3/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL, CL = 60 pF and CS is tied low.
1000
VDD - VOH @ VDD = 1.8V
VOL - VSS @ VDD = 1.8V
100
10
VDD = 5.5V
G = +1 V/V
VDD - VOH @ VDD = 5.5V
VOL - VSS @ VDD = 5.5V
1
10μ
100µ
1m
10m
Time (100 μs/Div)
Output Current (A)
FIGURE 2-25:
Output Voltage Headroom
FIGURE 2-28:
Small Signal Non-Inverting
vs. Output Current.
Pulse Response.
5.0
4.5
4.0
VDD = 5.5V
RL = 50 kΩ
VDD = 5.5V
G = -1 V/V
3.5
3.0
2.5
2.0
VDD - VOH
1.5
VSS - VOL
1.0
0.5
0.0
-50
-25
0
25
50
75
100 125
Time (100 μs/Div)
Ambient Temperature (°C)
FIGURE 2-26:
Output Voltage Headroom
FIGURE 2-29:
Small Signal Inverting Pulse
vs. Ambient Temperature.
Response.
7.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
Falling Edge, VDD = 5.5V
Falling Edge, VDD = 1.8V
6.0
5.0
4.0
3.0
2.0
1.0
Rising Edge, VDD = 5.5V
Rising Edge, VDD = 1.8V
VDD = 5.5V
G = +1 V/V
-50
-25
0
25
50
75
100
125
Ambient Temperature (°C)
Time (0.5 ms/div)
FIGURE 2-27:
Slew Rate vs. Ambient
FIGURE 2-30:
Large Signal Non-Inverting
Temperature.
Pulse Response.
DS22041B-page 10
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL, CL = 60 pF and CS is tied low.
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
VDD = 5.5V
VDD = 5.5V
G = -1 V/V
Output On
Hysteresis
CS Input
High to Low
CS Input
Low to High
Output High-Z
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Chip Select Voltage (V)
Time (0.5 ms/div)
FIGURE 2-31:
Large Signal Inverting Pulse
FIGURE 2-34:
Chip Select (CS) Hysteresis
Response.
(MCP6033 only) with V = 5.5V.
DD
2.1
6.0
5.0
4.0
3.0
2.0
1.0
VIN
VDD = 3.0V
VOUT
1.8
Output On
1.5
Hysteresis
1.2
0.9
0.6
0.3
0.0
CS Input
High to Low
CS Input
Low to High
VDD = 5.0V
G = +2 V/V
Output High-Z
0.0
-1.0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0
Chip Select Voltage (V)
Time (2 ms/div)
FIGURE 2-32:
The MCP6031/2/3/4 family
FIGURE 2-35:
Chip Select (CS) Hysteresis
shows no phase reversal .
(MCP6033 only) with V = 3.0V.
DD
1.5
1.2
6.0
5.0
4.0
3.0
2.0
1.0
0.0
-10
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
VDD = 1.8V
Output On
0.9
Chip Select
Hysteresis
0.6
0.3
0.0
CS Input
High to Low
CS Input
Low to High
Output On
VDD = 5.5V
G = +1 V/V
R
L = 50 kΩ to VSS
Output High-Z
Output
High-Z
Output
High-Z
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
Chip Select Voltage (V)
Time (1 ms/div)
FIGURE 2-33:
Chip Select (CS) to
FIGURE 2-36:
Chip Select (CS) Hysteresis
Amplifier Output Response Time (MCP6033
only).
(MCP6033 only) with V = 1.8V.
DD
© 2008 Microchip Technology Inc.
DS22041B-page 11
MCP6031/2/3/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 1 MΩ to VL, CL = 60 pF and CS is tied low.
10
100k
10m
1.00
1m
1.00E
10k
10
100µ
1.0
10µ
1.00E
1k
10
1µ
1.00E
100n
1.0
GN:
101 V/V
11 V/V
1 V/V
100
10n
1.00E
+125°C
+85°C
+25°C
-40°C
1n
1.00E
10
100p
1.00
10p
1.00E
1
1p
1.00E
1
10
100
1k
10k
100k
-1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0
VIN (V)
Frequency (Hz)
FIGURE 2-37:
Closed Loop Output
FIGURE 2-38:
Measured Input Current vs.
Impedance vs. Frequency.
Input Voltage (below V ).
SS
DS22041B-page 12
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
3.0
PIN DESCRIPTIONS
Descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
MCP6031
PIN FUNCTION TABLE
MCP6032
MCP6033
MCP6034
DFN,
MSOP,
SOIC
DFN,
MSOP,
SOIC
Symbol
Description
MSOP,
SOIC
SOIC,
TSSOP
SOT-23-5
1
4
6
2
1
2
3
8
5
6
6
2
1
2
3
4
5
6
VOUT, VOUTA
Analog Output (op amp A)
Inverting Input (op amp A)
Non-inverting Input (op amp A)
Positive Power Supply
VIN–, VINA
VIN+, VINA
VDD
–
+
3
3
3
5
7
7
—
—
—
—
—
—
VINB
+
–
Non-inverting Input (op amp B)
Inverting Input (op amp B)
VINB
—
—
—
—
2
—
—
7
—
—
—
—
4
7
VOUTB
VOUTC
Analog Output (op amp B)
Analog Output (op amp C)
Inverting Input (op amp C)
Non-inverting Input (op amp C)
Negative Power Supply
Non-inverting Input (op amp D)
Inverting Input (op amp D)
Analog Output (op amp D)
Chip Select
—
—
—
4
8
—
9
VINC
VINC
–
—
10
11
12
13
14
—
—
+
4
VSS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
8
VIND
VIND
+
—
–
—
VOUTD
CS
—
1, 5, 8
1, 5
NC
No Internal Connection
3.1
Analog Outputs
3.4
Power Supply Pins
The output pins are low-impedance voltage sources.
The positive power supply (VDD) is 1.8V to 5.5V higher
than the negative power supply (VSS). For normal
operation, the other pins are at voltages between VSS
3.2
Analog Inputs
and VDD
.
The non-inverting and inverting inputs are high-
impedance CMOS inputs with low bias currents.
Typically, these parts are used in a single (positive)
supply configuration. In this case, VSS is connected to
ground and VDD is connected to the supply. VDD will
need bypass capacitors.
3.3
Chip Select Digital Input
This is a CMOS, Schmitt-trigerred input that places the
device into a low power mode of operation.
© 2008 Microchip Technology Inc.
DS22041B-page 13
MCP6031/2/3/4
4.0
APPLICATION INFORMATION
VDD
The MCP6031/2/3/4 family of op amps is manufactured
using Microchip’s state-of-the-art CMOS process and
is specifically designed for low-power, high precision
applications.
D1 D2
R1
V1
V2
4.1
Rail-to-Rail Input
MCP603X
4.1.1
PHASE REVERASAL
R2
The MCP6031/2/3/4 op amps are designed to prevent
phase reversal when the input pins exceed the supply
voltages. Figure 2-32 shows the input voltage exceed-
ing the supply voltage without any phase reversal.
R3
VSS – (minimum expected V1)
R1 >
R2 >
2 mA
VSS – (minimum expected V2)
2 mA
4.1.2
INPUT VOLTAGE AND CURRENT
LIMITS
The ESD protection on the inputs can be depicted as
shown in Figure 4-1. This structure was chosen to
protect the input transistors and to minimize input bias
current (IB). The input ESD diodes clamp the inputs
when they try to go more than one diode drop below
VSS. They also clamp any voltage that go too far above
VDD; their breakdown voltage is high enough to allow
normal operation and low enough to bypass ESD
events within the specified limits.
FIGURE 4-2:
Inputs.
Protecting the Analog
It is also possible to connect the diodes to the left of the
resistors R1 and R2. In this case, the currents through
the diodes D1 and D2 need to be limited by some other
mechanism. The resistors then serve as in-rush current
limiters; the DC currents into the input pins (VIN+ and
VIN-) should be very small. A significant amount of
current can flow out of the inputs when the common
mode voltage (VCM) is below ground (VSS).
Bond
VDD
Pad
4.1.3
NORMAL OPERATION
The input stage of the MCP6031/2/3/4 op amps uses
two differential input stages in parallel. One operates at
a low common mode input voltage (VCM), while the
other operates at a high VCM. With this topology, the
device operates with a VCM up to 300 mV above VDD
and 300 mV below VSS. The input offset voltage is
measured at VCM = VSS – 0.3V and VDD + 0.3V to
ensure proper operation.
Bond
Pad
Bond
Pad
Input
Stage
VIN+
VIN–
Bond
Pad
VSS
There are two transitions in input behavior as VCM is
changed. The first occurs, when VCM is near
VSS + 0.4V, and the second occurs when VCM is near
VDD – 0.5V. For the best distortion performance with
non-inverting gains, avoid these regions of operation.
FIGURE 4-1:
Structures.
Simplified Analog Input ESD
In order to prevent damage and/or improper operation
of these op amps, the circuit they are in must limit the
voltages and currents at the VIN+ and VIN- pins (see
Absolute Maximum Ratings at the beginning of
Section 1.0 “Electrical Characteristics”). Figure 4-2
shows the recommended approach to protecting these
inputs. The internal ESD diodes prevent the input pins
(VIN+ and VIN-) from going too far below ground, and
the resistors R1 and R2 limit the possible current drawn
out of the input pins. Diodes D1 and D2 prevent the
input pins (VIN+ and VIN-) from going too far above VDD
.
When implemented as shown, resistors R1 and R2 also
limit the current through D1 and D2.
DS22041B-page 14
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
4.2
Rail-to-Rail Output
The output voltage range of the MCP6031/2/3/4 op
amps is VSS + 10 mV (minimum) and VDD – 10 mV
(maximum) when RL = 50 kΩ is connected to VDD/2
and VDD = 5.5V. Refer to Figures 2-25 and 2-26 for
more information.
–
RISO
VOUT
MCP603X
+
VIN
CL
4.3
Output Loads and Battery Life
FIGURE 4-3:
stabilizes large capacitive loads.
Output resistor, R
ISO
The MCP6031/2/3/4 op amp family has outstanding
quiescent current, which supports battery-powered
applications. There is minimal quiescent current glitch-
ing when Chip Select (CS) is raised or lowered. This
prevents excessive current draw, and reduced battery
life, when the part is turned off or on.
Figure 4-4 gives recommended RISO values for
different capacitive loads and gains. The x-axis is the
normalized load capacitance (CL/GN), where GN is the
circuit's noise gain. For non-inverting gains, GN and the
Signal Gain are equal. For inverting gains, GN is
1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V).
Heavy resistive loads at the output can cause exces-
sive battery drain. Driving a DC voltage of 2.5V across
a 100 kΩ load resistor will cause the supply current to
increase by 25 µA, depleting the battery 28 times as
fast as IQ (0.9 µA, typical) alone.
10001M
High frequency signals (fast edge rate) across capaci-
tive loads will also significantly increase supply current.
For instance, a 0.1 µF capacitor at the output presents
an AC impedance of 15.9 kΩ (1/2πfC) to a 100 Hz
sinewave. It can be shown that the average power
drawn from the battery by a 5.0 Vp-p sinewave
(1.77 Vrms), under these conditions, is
100k
10
GN:
1 V/V
2 V/V
≥ 5 V/V
10k
10
1k
10
10p
100p
1n
10n
100n
1µ
Normalized Load Capacitance; CL/GN (F)
EQUATION 4-1:
PSupply = (VDD - VSS) (IQ + VL(p-p) f CL )
= (5V)(0.9 µA + 5.0Vp-p · 100Hz · 0.1µF)
= 4.5 µW + 50 µW
FIGURE 4-4:
for Capacitive Loads.
Recommended R
values
ISO
After selecting RISO for your circuit, double-check the
resulting frequency response peaking and step
response overshoot. Modify RISO’s value until the
response is reasonable. Bench evaluation and simula-
tions with the MCP6031/2/3/4 SPICE macro model are
very helpful.
This will drain the battery about 12 times as fast as IQ
alone.
4.4
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response, with overshoot and ringing in the step
response. While a unity-gain buffer (G = +1) is the most
sensitive to capacitive loads, all gains show the same
general behavior.
4.5
MCP6033 Chip Select
The MCP6033 is a single op amp with Chip Select
(CS). When CS is pulled high, the supply current drops
to 0.4 nA (typical) and flows through the CS pin to VSS
.
When this happens, the amplifier output is put into a
high impedance state. By pulling CS low, the amplifier
is enabled. If the CS pin is left floating, the amplifier will
not operate properly. Figure 1-1 shows the output
voltage and supply current response to a CS pulse.
When driving large capacitive loads with these op
amps (e.g., > 100 pF when G = +1), a small series
resistor at the output (RISO in Figure 4-3) improves the
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. The
bandwidth will be generally lower than the bandwidth
with no capacitance load.
© 2008 Microchip Technology Inc.
DS22041B-page 15
MCP6031/2/3/4
4.6
Supply Bypass
With this family of operational amplifiers, the power
supply pin (VDD for single-supply) should have a local
bypass capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm
for good high frequency performance. It can use a bulk
capacitor (i.e., 1 µF or larger) within 100 mm to provide
large, slow currents. This bulk capacitor can be shared
with other analog parts.
Guard Ring
VIN– VIN+
VSS
4.7
Unused Op Amps
FIGURE 4-6:
for Inverting Gain.
Example Guard Ring Layout
An unused op amp in a quad package (MCP6034)
should be configured as shown in Figure 4-5. These
circuits prevent the output from toggling and causing
crosstalk. Circuits A sets the op amp at its minimum
noise gain. The resistor divider produces any desired
reference voltage within the output voltage range of the
op amp; the op amp buffers that reference voltage.
Circuit B uses the minimum number of components
and operates as a comparator, but it may draw more
current.
1. Non-inverting Gain and Unity-Gain Buffer:
a. Connect the non-inverting pin (VIN+) to the
input with a wire that does not touch the
PCB surface.
b. Connect the guard ring to the inverting input
pin (VIN–). This biases the guard ring to the
common mode input voltage.
2. Inverting Gain and Transimpedance Gain Ampli-
fiers (convert current to voltage, such as photo
detectors):
¼ MCP6034 (A)
VDD
¼ MCP6034 (B)
a. Connect the guard ring to the non-inverting
input pin (VIN+). This biases the guard ring
to the same reference voltage as the op
amp (e.g., VDD/2 or ground).
VDD
VDD
R1
R2
b. Connect the inverting pin (VIN–) to the input
with a wire that does not touch the PCB
surface.
VREF
R2
------------------
⋅
VREF = VDD
R1 + R2
FIGURE 4-5:
Unused Op Amps.
4.8
PCB Surface Leakage
In applications where low input bias current is critical,
Printed Circuit Board (PCB) surface leakage effects
need to be considered. Surface leakage is caused by
humidity, dust or other contamination on the board.
Under low humidity conditions, a typical resistance
between nearby traces is 1012Ω. A 5V difference would
cause 5 pA of current to flow; which is greater than the
MCP6031/2/3/4 family’s bias current at +25°C
(±1.0 pA, typical).
The easiest way to reduce surface leakage is to use a
guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin.
An example of this type of layout is shown in
Figure 4-6.
DS22041B-page 16
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
4.9.2
PRECISION COMPARATOR
4.9
Application Circuits
Use high gain before a comparator to improve the lat-
ter’s input offset performance. Figure 4-8 shows a gain
of 11 V/V placed before a comparator. The reference
voltage VREF can be any value between the supply
rails.
4.9.1
BATTERY CURRENT SENSING
The MCP6031/2/3/4 op amps’ Common Mode Input
Range, which goes 0.3V beyond both supply rails,
supports their use in high side and low side battery
current sensing applications. The ultra low quiescent
current (0.9 µA, typical) helps prolong battery life, and
the rail-to-rail output supports detection of low currents.
VIN
MCP6031
Figure 4-7 shows a high side battery current sensor
circuit. The 10Ω resistor is sized to minimize power
losses. The battery current (IDD) through the 10Ω
resistor causes its top terminal to be more negative
than the bottom terminal. This keeps the common
mode input voltage of the op amp below VDD, which is
within its allowed range. The output of the op amp will
also be below VDD, which is within its Maximum Output
Voltage Swing specification.
1 MΩ
VOUT
MCP6541
100 kΩ
VREF
FIGURE 4-8:
Comparator.
Precision, Non-inverting
4.9.3
DRIVING MCP3421 ΔΣ A/D
CONVERTER
IDD
VDD
A RSH and CSH snubber reduces the output impedance
of MCP6031 op amp, which reduces the gain error
caused by switching transients, which occur at the
MCP3421 ADC's sampling rate. The snubber also
maintains feedback stability and avoids AC response
peaking and step response overshoot and ringing
(caused by the op amp’s inductive output impedance
resonating with the ADC’s input capacitance). The cost
for this improvement is low. Best of all, using an op amp
with higher supply current is avoided. See Figure 4-9.
This figure also includes a resistor to balance the
impedance at the ADC's inputs (RBAL) at the sampling
frequency; it may not be needed in all designs.
1.4V
to
5.5V
10Ω
VOUT
MCP6031
1 MΩ
100 kΩ
VDD – VOUT
IDD = -----------------------------------------
(10 V/V) ⋅ (10Ω)
FIGURE 4-7:
Sensor.
High Side Battery Current
ZIND
MCP6031
MCP3421
1.00 kΩ 2.25 MΩ
VIN
ΔΣ
RSH
1.00 kΩ
CSH
2.2 µF
RBAL
1.00 kΩ
FIGURE 4-9:
Driving the MCP3421 using
an R-C Snubber.
© 2008 Microchip Technology Inc.
DS22041B-page 17
MCP6031/2/3/4
5.5
Analog Demonstration and
Evaluation Boards
5.0
DESIGN AIDS
Microchip provides the basic design tools needed for
the MCP6031/2/3/4 family of op amps.
Microchip offers
a
broad spectrum of Analog
Demonstration and Evaluation Boards that are
designed to help you achieve faster time to market. For
5.1
SPICE Macro Model
a
complete listing of these boards and their
The latest SPICE macro model for the MCP6031/2/3/4
op amps is available on the Microchip web site at
www.microchip.com. This model is intended to be an
initial design tool that works well in the op amp’s linear
region of operation over the temperature range. See
the model file for information on its capabilities.
corresponding user’s guides and technical information,
visit the Microchip web site at www.microchip.com/
analogtools.
Two of our boards that are especially useful are:
• P/N SOIC8EV: 8-Pin SOIC/MSOP/TSSOP/DIP
Evaluation Board
Bench testing is a very important part of any design and
cannot be replaced with simulations. Also, simulation
results using this macro model need to be validated by
comparing them to the data sheet specifications and
characteristic curves.
• P/N SOIC14EV: 14-Pin SOIC/TSSOP/DIP Evalu-
ation Board
5.6
Application Notes
The following Microchip Analog Design Note and
Application Notes are available on the Microchip web
site at www.microchip. com/appnotes and are recom-
mended as supplemental reference resources.
5.2
FilterLab® Software
Microchip’s FilterLab® software is an innovative
software tool that simplifies analog active filter (using
op amps) design. Available at no cost from the
Microchip web site at www.microchip.com/filterlab, the
FilterLab design tool provides full schematic diagrams
of the filter circuit with component values. It also
outputs the filter circuit in SPICE format, which can be
used with the macro model to simulate actual filter
performance.
ADN003: “Select the Right Operational Amplifier for
your Filtering Circuits”, DS21821
AN722: “Operational Amplifier Topologies and DC
Specifications”, DS00722
AN723: “Operational Amplifier AC Specifications and
Applications”, DS00723
AN884: “Driving Capacitive Loads With Op Amps”,
5.3
Mindi™ Circuit Designer &
Simulator
DS00884
AN990: “Analog Sensor Conditioning Circuits – An
Overview”, DS00990
Microchip’s Mindi™ Circuit Designer & Simulator aids
in the design of various circuits useful for active filter,
amplifier and power-management applications. It is a
free online circuit designer & simulator available from
the Microchip web site at www.microchip.com/mindi.
This interactive circuit designer & simulator enables
designers to quickly generate circuit diagrams,
simulate circuits. Circuits developed using the Mindi
Circuit Designer & Simulator can be downloaded to a
personal computer or workstation.
These application notes and others are listed in the
design guide:
“Signal Chain Design Guide”, DS21825
5.4
MAPS (Microchip Advanced Part
Selector)
MAPS is a software tool that helps semiconductor
professionals efficiently identify Microchip devices that
fit a particular design requirement. Available at no cost
from the Microchip website at www.microchip.com/
maps, the MAPS is an overall selection tool for
Microchip’s product portfolio that includes Analog,
Memory, MCUs and DSCs. Using this tool you can
define a filter to sort features for a parametric search of
devices and export side-by-side technical comparasion
reports. Helpful links are also provided for Datasheets,
Purchase, and Sampling of Microchip parts.
DS22041B-page 18
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
6.0
6.1
PACKAGING INFORMATION
Package Marking Information
Example:
5-Lead SOT-23 (MCP6031)
E-Temp
Code
Device
XXNN
EA25
MCP6031T-E/OT
EANN
8-Lead 2x3 DFN (MCP6031 & MCP6033)
Example:
XXX
YWW
NN
ABV
809
25
Example:
8-Lead MSOP
XXXXXX
YWWNNN
6031E
809256
8-Lead SOIC (150 mil)
Example:
XXXXXXXX
MCP6033E
e
3
XXXXYYWW
SN0809
NNN
256
Legend: XX...X Customer-specific information
Y
YY
WW
NNN
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
*
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
)
e3
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2008 Microchip Technology Inc.
DS22041B-page 19
MCP6031/2/3/4
Package Marking Information (Continued)
14-Lead SOIC (150 mil) (MCP6034)
Example:
XXXXXXXXXX
XXXXXXXXXX
MCP6034
E/SL^
0711256
e
3
YYWWNNN
Example:
14-Lead TSSOP (MCP6034)
XXXXXX
YYWW
6034EST
0711
256
NNN
Legend: XX...X Customer-specific information
Y
YY
WW
NNN
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
*
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
)
e3
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
DS22041B-page 20
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢒꢓꢄꢑꢉꢋꢉꢊꢔꢓꢆꢕꢏꢒꢖꢆꢗꢍꢏꢒꢁꢘꢙꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
b
N
E
E1
3
2
1
e
e1
D
A2
c
A
φ
A1
L
L1
.ꢆꢃꢍꢇ
ꢕ/00/ꢕꢌ%ꢌ1ꢜ
ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢉ0ꢃꢄꢃꢍꢇ
ꢕ/2
23ꢕ
ꢕꢛ4
2ꢐꢄ5ꢅꢓꢉꢈꢑꢉ,ꢃꢆꢇ
0ꢅꢊꢋꢉ,ꢃꢍꢎꢒ
2
ꢅ
!
ꢗꢁ6!ꢉ"ꢜ#
3ꢐꢍꢇꢃꢋꢅꢉ0ꢅꢊꢋꢉ,ꢃꢍꢎꢒ
3'ꢅꢓꢊꢏꢏꢉ7ꢅꢃꢚꢒꢍ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
ꢜꢍꢊꢆꢋꢈꢑꢑ
3'ꢅꢓꢊꢏꢏꢉ;ꢃꢋꢍꢒ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ;ꢃꢋꢍꢒ
3'ꢅꢓꢊꢏꢏꢉ0ꢅꢆꢚꢍꢒ
)ꢈꢈꢍꢉ0ꢅꢆꢚꢍꢒ
)ꢈꢈꢍꢔꢓꢃꢆꢍ
)ꢈꢈꢍꢉꢛꢆꢚꢏꢅ
0ꢅꢊꢋꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
0ꢅꢊꢋꢉ;ꢃꢋꢍꢒ
ꢅꢀ
ꢛ
ꢛꢘ
ꢛꢀ
ꢌ
ꢌꢀ
ꢂ
0
ꢀꢁ6ꢗꢉ"ꢜ#
ꢗꢁ6ꢗ
ꢗꢁ96
ꢗꢁꢗꢗ
ꢘꢁꢘꢗ
ꢀꢁ:ꢗ
ꢘꢁꢙꢗ
ꢗꢁꢀꢗ
ꢗꢁ:!
ꢗꢞ
M
M
M
M
M
M
M
M
M
M
M
ꢀꢁ !
ꢀꢁ:ꢗ
ꢗꢁꢀ!
:ꢁꢘꢗ
ꢀꢁ9ꢗ
:ꢁꢀꢗ
ꢗꢁ<ꢗ
ꢗꢁ9ꢗ
:ꢗꢞ
0ꢀ
ꢀ
ꢎ
5
ꢗꢁꢗ9
ꢗꢁꢘꢗ
ꢗꢁꢘ<
ꢗꢁ!ꢀ
ꢛꢔꢊꢃꢉꢜ
ꢀꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢇꢉꢂꢉꢊꢆꢋꢉꢌꢀꢉꢋꢈꢉꢆꢈꢍꢉꢃꢆꢎꢏꢐꢋꢅꢉꢄꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢁꢉꢕꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢉꢇꢒꢊꢏꢏꢉꢆꢈꢍꢉꢅꢖꢎꢅꢅꢋꢉꢗꢁꢀꢘꢙꢉꢄꢄꢉꢔꢅꢓꢉꢇꢃꢋꢅꢁ
ꢘꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢃꢆꢚꢉꢊꢆꢋꢉꢍꢈꢏꢅꢓꢊꢆꢎꢃꢆꢚꢉꢔꢅꢓꢉꢛꢜꢕꢌꢉꢝꢀ ꢁ!ꢕꢁ
"ꢜ#$ "ꢊꢇꢃꢎꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆꢁꢉ%ꢒꢅꢈꢓꢅꢍꢃꢎꢊꢏꢏ&ꢉꢅꢖꢊꢎꢍꢉ'ꢊꢏꢐꢅꢉꢇꢒꢈ(ꢆꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅꢇꢁ
ꢕꢃꢎꢓꢈꢎꢒꢃꢔ %ꢅꢎꢒꢆꢈꢏꢈꢚ& ꢂꢓꢊ(ꢃꢆꢚ #ꢗ >ꢗ6ꢀ"
© 2008 Microchip Technology Inc.
DS22041B-page 21
MCP6031/2/3/4
ꢝꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ ꢐꢄꢈꢆ!ꢈꢄꢊ"ꢆꢛꢔꢆꢂꢃꢄꢅꢆꢇꢄꢌ#ꢄ$ꢃꢆꢕ%&ꢖꢆMꢆꢘ(ꢙ()*+ꢆꢎꢎꢆ,ꢔꢅ-ꢆꢗ !ꢛꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
e
D
b
N
N
L
K
E2
E
EXPOSED PAD
NOTE 1
NOTE 1
2
1
1
2
D2
BOTTOM VIEW
TOP VIEW
A
NOTE 2
A3
A1
.ꢆꢃꢍꢇ
ꢕ/00/ꢕꢌ%ꢌ1ꢜ
ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢉ0ꢃꢄꢃꢍꢇ
ꢕ/2
23ꢕ
9
ꢗꢁ!ꢗꢉ"ꢜ#
ꢗꢁ6ꢗ
ꢕꢛ4
2ꢐꢄ5ꢅꢓꢉꢈꢑꢉ,ꢃꢆꢇ
,ꢃꢍꢎꢒ
3'ꢅꢓꢊꢏꢏꢉ7ꢅꢃꢚꢒꢍ
ꢜꢍꢊꢆꢋꢈꢑꢑꢉ
#ꢈꢆꢍꢊꢎꢍꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
3'ꢅꢓꢊꢏꢏꢉ0ꢅꢆꢚꢍꢒ
3'ꢅꢓꢊꢏꢏꢉ;ꢃꢋꢍꢒ
2
ꢅ
ꢛ
ꢛꢀ
ꢛ:
ꢂ
ꢗꢁ9ꢗ
ꢗꢁꢗꢗ
ꢀꢁꢗꢗ
ꢗꢁꢗ!
ꢗꢁꢗꢘ
ꢗꢁꢘꢗꢉ1ꢌ)
ꢘꢁꢗꢗꢉ"ꢜ#
:ꢁꢗꢗꢉ"ꢜ#
M
M
ꢗꢁꢘ!
ꢌ
ꢌꢖꢔꢈꢇꢅꢋꢉ,ꢊꢋꢉ0ꢅꢆꢚꢍꢒ
ꢌꢖꢔꢈꢇꢅꢋꢉ,ꢊꢋꢉ;ꢃꢋꢍꢒ
#ꢈꢆꢍꢊꢎꢍꢉ;ꢃꢋꢍꢒ
#ꢈꢆꢍꢊꢎꢍꢉ0ꢅꢆꢚꢍꢒ
#ꢈꢆꢍꢊꢎꢍ>ꢍꢈ>ꢌꢖꢔꢈꢇꢅꢋꢉ,ꢊꢋ
ꢂꢘ
ꢌꢘ
5
0
?
ꢀꢁ:ꢗ
ꢀꢁ!ꢗ
ꢗꢁꢘꢗ
ꢗꢁ:ꢗ
ꢗꢁꢘꢗ
ꢀꢁ!!
ꢀꢁꢙ!
ꢗꢁ:ꢗ
ꢗꢁ!ꢗ
M
ꢗꢁ ꢗ
M
ꢛꢔꢊꢃꢉꢜ
ꢀꢁ ,ꢃꢆꢉꢀꢉ'ꢃꢇꢐꢊꢏꢉꢃꢆꢋꢅꢖꢉꢑꢅꢊꢍꢐꢓꢅꢉꢄꢊ&ꢉ'ꢊꢓ&+ꢉ5ꢐꢍꢉꢄꢐꢇꢍꢉ5ꢅꢉꢏꢈꢎꢊꢍꢅꢋꢉ(ꢃꢍꢒꢃꢆꢉꢍꢒꢅꢉꢒꢊꢍꢎꢒꢅꢋꢉꢊꢓꢅꢊꢁ
ꢘꢁ ,ꢊꢎ*ꢊꢚꢅꢉꢄꢊ&ꢉꢒꢊ'ꢅꢉꢈꢆꢅꢉꢈꢓꢉꢄꢈꢓꢅꢉꢅꢖꢔꢈꢇꢅꢋꢉꢍꢃꢅꢉ5ꢊꢓꢇꢉꢊꢍꢉꢅꢆꢋꢇꢁ
:ꢁ ,ꢊꢎ*ꢊꢚꢅꢉꢃꢇꢉꢇꢊ(ꢉꢇꢃꢆꢚꢐꢏꢊꢍꢅꢋꢁ
ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢃꢆꢚꢉꢊꢆꢋꢉꢍꢈꢏꢅꢓꢊꢆꢎꢃꢆꢚꢉꢔꢅꢓꢉꢛꢜꢕꢌꢉꢝꢀ ꢁ!ꢕꢁ
"ꢜ#$ "ꢊꢇꢃꢎꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆꢁꢉ%ꢒꢅꢈꢓꢅꢍꢃꢎꢊꢏꢏ&ꢉꢅꢖꢊꢎꢍꢉ'ꢊꢏꢐꢅꢉꢇꢒꢈ(ꢆꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅꢇꢁ
1ꢌ)$ 1ꢅꢑꢅꢓꢅꢆꢎꢅꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆ+ꢉꢐꢇꢐꢊꢏꢏ&ꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅ+ꢉꢑꢈꢓꢉꢃꢆꢑꢈꢓꢄꢊꢍꢃꢈꢆꢉꢔꢐꢓꢔꢈꢇꢅꢇꢉꢈꢆꢏ&ꢁ
ꢕꢃꢎꢓꢈꢎꢒꢃꢔ %ꢅꢎꢒꢆꢈꢏꢈꢚ& ꢂꢓꢊ(ꢃꢆꢚ #ꢗ >ꢀꢘ:#
DS22041B-page 22
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
ꢝꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ ꢐꢄꢈꢆ!ꢈꢄꢊ"ꢆꢛꢔꢆꢂꢃꢄꢅꢆꢇꢄꢌ#ꢄ$ꢃꢆꢕ%&ꢖꢆMꢆꢘ(ꢙ()*+ꢆꢎꢎꢆ,ꢔꢅ-ꢆꢗ !ꢛꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
© 2008 Microchip Technology Inc.
DS22041B-page 23
MCP6031/2/3/4
ꢝꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ%ꢋꢌꢓꢔꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢇꢄꢌ#ꢄ$ꢃꢆꢕ%ꢍꢖꢆꢗ%ꢍꢏꢇꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
D
N
E
E1
NOTE 1
2
b
1
e
c
φ
A2
A
L
L1
A1
.ꢆꢃꢍꢇ
ꢕ/00/ꢕꢌ%ꢌ1ꢜ
ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢉ0ꢃꢄꢃꢍꢇ
ꢕ/2
23ꢕ
ꢕꢛ4
2ꢐꢄ5ꢅꢓꢉꢈꢑꢉ,ꢃꢆꢇ
,ꢃꢍꢎꢒ
2
ꢅ
9
ꢗꢁ<!ꢉ"ꢜ#
3'ꢅꢓꢊꢏꢏꢉ7ꢅꢃꢚꢒꢍ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
ꢜꢍꢊꢆꢋꢈꢑꢑꢉ
3'ꢅꢓꢊꢏꢏꢉ;ꢃꢋꢍꢒ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ;ꢃꢋꢍꢒ
3'ꢅꢓꢊꢏꢏꢉ0ꢅꢆꢚꢍꢒ
)ꢈꢈꢍꢉ0ꢅꢆꢚꢍꢒ
ꢛ
M
ꢗꢁꢙ!
ꢗꢁꢗꢗ
M
ꢗꢁ9!
ꢀꢁꢀꢗ
ꢗꢁ6!
ꢗꢁꢀ!
ꢛꢘ
ꢛꢀ
ꢌ
ꢌꢀ
ꢂ
M
ꢁ6ꢗꢉ"ꢜ#
:ꢁꢗꢗꢉ"ꢜ#
:ꢁꢗꢗꢉ"ꢜ#
ꢗꢁ<ꢗ
0
ꢗꢁ ꢗ
ꢗꢁ9ꢗ
)ꢈꢈꢍꢔꢓꢃꢆꢍ
)ꢈꢈꢍꢉꢛꢆꢚꢏꢅ
0ꢀ
ꢀ
ꢗꢁ6!ꢉ1ꢌ)
M
ꢗꢞ
9ꢞ
0ꢅꢊꢋꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
0ꢅꢊꢋꢉ;ꢃꢋꢍꢒ
ꢎ
5
ꢗꢁꢗ9
ꢗꢁꢘꢘ
M
M
ꢗꢁꢘ:
ꢗꢁ ꢗ
ꢛꢔꢊꢃꢉꢜ
ꢀꢁ ,ꢃꢆꢉꢀꢉ'ꢃꢇꢐꢊꢏꢉꢃꢆꢋꢅꢖꢉꢑꢅꢊꢍꢐꢓꢅꢉꢄꢊ&ꢉ'ꢊꢓ&+ꢉ5ꢐꢍꢉꢄꢐꢇꢍꢉ5ꢅꢉꢏꢈꢎꢊꢍꢅꢋꢉ(ꢃꢍꢒꢃꢆꢉꢍꢒꢅꢉꢒꢊꢍꢎꢒꢅꢋꢉꢊꢓꢅꢊꢁ
ꢘꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢇꢉꢂꢉꢊꢆꢋꢉꢌꢀꢉꢋꢈꢉꢆꢈꢍꢉꢃꢆꢎꢏꢐꢋꢅꢉꢄꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢁꢉꢕꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢉꢇꢒꢊꢏꢏꢉꢆꢈꢍꢉꢅꢖꢎꢅꢅꢋꢉꢗꢁꢀ!ꢉꢄꢄꢉꢔꢅꢓꢉꢇꢃꢋꢅꢁ
:ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢃꢆꢚꢉꢊꢆꢋꢉꢍꢈꢏꢅꢓꢊꢆꢎꢃꢆꢚꢉꢔꢅꢓꢉꢛꢜꢕꢌꢉꢝꢀ ꢁ!ꢕꢁ
"ꢜ#$ "ꢊꢇꢃꢎꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆꢁꢉ%ꢒꢅꢈꢓꢅꢍꢃꢎꢊꢏꢏ&ꢉꢅꢖꢊꢎꢍꢉ'ꢊꢏꢐꢅꢉꢇꢒꢈ(ꢆꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅꢇꢁ
1ꢌ)$ 1ꢅꢑꢅꢓꢅꢆꢎꢅꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆ+ꢉꢐꢇꢐꢊꢏꢏ&ꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅ+ꢉꢑꢈꢓꢉꢃꢆꢑꢈꢓꢄꢊꢍꢃꢈꢆꢉꢔꢐꢓꢔꢈꢇꢅꢇꢉꢈꢆꢏ&ꢁ
ꢕꢃꢎꢓꢈꢎꢒꢃꢔ %ꢅꢎꢒꢆꢈꢏꢈꢚ& ꢂꢓꢊ(ꢃꢆꢚ #ꢗ >ꢀꢀꢀ"
DS22041B-page 24
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
ꢝꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢕꢍꢛꢖꢆMꢆꢛꢄꢓꢓꢔ."ꢆꢙ*+)ꢆꢎꢎꢆ,ꢔꢅ-ꢆꢗꢍꢏ/&ꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
c
φ
A2
A
L
A1
L1
β
.ꢆꢃꢍꢇ
ꢕ/00/ꢕꢌ%ꢌ1ꢜ
ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢉ0ꢃꢄꢃꢍꢇ
ꢕ/2
23ꢕ
ꢕꢛ4
2ꢐꢄ5ꢅꢓꢉꢈꢑꢉ,ꢃꢆꢇ
,ꢃꢍꢎꢒ
2
ꢅ
9
ꢀꢁꢘꢙꢉ"ꢜ#
3'ꢅꢓꢊꢏꢏꢉ7ꢅꢃꢚꢒꢍ
ꢛ
M
ꢀꢁꢘ!
ꢗꢁꢀꢗ
M
M
M
ꢀꢁꢙ!
M
ꢗꢁꢘ!
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
ꢜꢍꢊꢆꢋꢈꢑꢑꢉꢉ
ꢛꢘ
ꢛꢀ
ꢌ
ꢟ
3'ꢅꢓꢊꢏꢏꢉ;ꢃꢋꢍꢒ
<ꢁꢗꢗꢉ"ꢜ#
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ;ꢃꢋꢍꢒ
3'ꢅꢓꢊꢏꢏꢉ0ꢅꢆꢚꢍꢒ
#ꢒꢊꢄꢑꢅꢓꢉAꢈꢔꢍꢃꢈꢆꢊꢏB
)ꢈꢈꢍꢉ0ꢅꢆꢚꢍꢒ
ꢌꢀ
ꢂ
ꢒ
:ꢁ6ꢗꢉ"ꢜ#
ꢁ6ꢗꢉ"ꢜ#
ꢗꢁꢘ!
ꢗꢁ ꢗ
M
M
ꢗꢁ!ꢗ
ꢀꢁꢘꢙ
0
)ꢈꢈꢍꢔꢓꢃꢆꢍ
)ꢈꢈꢍꢉꢛꢆꢚꢏꢅ
0ꢅꢊꢋꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
0ꢅꢊꢋꢉ;ꢃꢋꢍꢒ
ꢕꢈꢏꢋꢉꢂꢓꢊꢑꢍꢉꢛꢆꢚꢏꢅꢉ%ꢈꢔ
ꢕꢈꢏꢋꢉꢂꢓꢊꢑꢍꢉꢛꢆꢚꢏꢅꢉ"ꢈꢍꢍꢈꢄ
0ꢀ
ꢀ
ꢀꢁꢗ ꢉ1ꢌ)
ꢗꢞ
ꢗꢁꢀꢙ
ꢗꢁ:ꢀ
!ꢞ
M
M
M
M
M
9ꢞ
ꢎ
5
ꢁ
ꢗꢁꢘ!
ꢗꢁ!ꢀ
ꢀ!ꢞ
ꢂ
!ꢞ
ꢀ!ꢞ
ꢛꢔꢊꢃꢉꢜ
ꢀꢁ ,ꢃꢆꢉꢀꢉ'ꢃꢇꢐꢊꢏꢉꢃꢆꢋꢅꢖꢉꢑꢅꢊꢍꢐꢓꢅꢉꢄꢊ&ꢉ'ꢊꢓ&+ꢉ5ꢐꢍꢉꢄꢐꢇꢍꢉ5ꢅꢉꢏꢈꢎꢊꢍꢅꢋꢉ(ꢃꢍꢒꢃꢆꢉꢍꢒꢅꢉꢒꢊꢍꢎꢒꢅꢋꢉꢊꢓꢅꢊꢁ
ꢘꢁ ꢟꢉꢜꢃꢚꢆꢃꢑꢃꢎꢊꢆꢍꢉ#ꢒꢊꢓꢊꢎꢍꢅꢓꢃꢇꢍꢃꢎꢁ
:ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢇꢉꢂꢉꢊꢆꢋꢉꢌꢀꢉꢋꢈꢉꢆꢈꢍꢉꢃꢆꢎꢏꢐꢋꢅꢉꢄꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢁꢉꢕꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢉꢇꢒꢊꢏꢏꢉꢆꢈꢍꢉꢅꢖꢎꢅꢅꢋꢉꢗꢁꢀ!ꢉꢄꢄꢉꢔꢅꢓꢉꢇꢃꢋꢅꢁ
ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢃꢆꢚꢉꢊꢆꢋꢉꢍꢈꢏꢅꢓꢊꢆꢎꢃꢆꢚꢉꢔꢅꢓꢉꢛꢜꢕꢌꢉꢝꢀ ꢁ!ꢕꢁ
"ꢜ#$ "ꢊꢇꢃꢎꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆꢁꢉ%ꢒꢅꢈꢓꢅꢍꢃꢎꢊꢏꢏ&ꢉꢅꢖꢊꢎꢍꢉ'ꢊꢏꢐꢅꢉꢇꢒꢈ(ꢆꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅꢇꢁ
1ꢌ)$ 1ꢅꢑꢅꢓꢅꢆꢎꢅꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆ+ꢉꢐꢇꢐꢊꢏꢏ&ꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅ+ꢉꢑꢈꢓꢉꢃꢆꢑꢈꢓꢄꢊꢍꢃꢈꢆꢉꢔꢐꢓꢔꢈꢇꢅꢇꢉꢈꢆꢏ&ꢁ
ꢕꢃꢎꢓꢈꢎꢒꢃꢔ %ꢅꢎꢒꢆꢈꢏꢈꢚ& ꢂꢓꢊ(ꢃꢆꢚ #ꢗ >ꢗ!ꢙ"
© 2008 Microchip Technology Inc.
DS22041B-page 25
MCP6031/2/3/4
ꢝꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢕꢍꢛꢖꢆMꢆꢛꢄꢓꢓꢔ."ꢆꢙ*+)ꢆꢎꢎꢆ,ꢔꢅ-ꢆꢗꢍꢏ/&ꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
DS22041B-page 26
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
01ꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢕꢍꢂꢖꢆMꢆꢛꢄꢓꢓꢔ."ꢆꢙ*+)ꢆꢎꢎꢆ,ꢔꢅ-ꢆꢗꢍꢏ/&ꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
D
N
E
E1
NOTE 1
1
2
3
e
h
b
α
h
c
φ
A2
A
L
A1
β
L1
.ꢆꢃꢍꢇ
ꢕ/00/ꢕꢌ%ꢌ1ꢜ
ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢉ0ꢃꢄꢃꢍꢇ
ꢕ/2
23ꢕ
ꢕꢛ4
2ꢐꢄ5ꢅꢓꢉꢈꢑꢉ,ꢃꢆꢇ
,ꢃꢍꢎꢒ
2
ꢅ
ꢀ
ꢀꢁꢘꢙꢉ"ꢜ#
3'ꢅꢓꢊꢏꢏꢉ7ꢅꢃꢚꢒꢍ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
ꢜꢍꢊꢆꢋꢈꢑꢑꢉꢉꢟ
ꢛ
M
ꢀꢁꢘ!
ꢗꢁꢀꢗ
M
M
M
ꢀꢁꢙ!
M
ꢗꢁꢘ!
ꢛꢘ
ꢛꢀ
ꢌ
3'ꢅꢓꢊꢏꢏꢉ;ꢃꢋꢍꢒ
<ꢁꢗꢗꢉ"ꢜ#
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ;ꢃꢋꢍꢒ
3'ꢅꢓꢊꢏꢏꢉ0ꢅꢆꢚꢍꢒ
#ꢒꢊꢄꢑꢅꢓꢉAꢈꢔꢍꢃꢈꢆꢊꢏB
)ꢈꢈꢍꢉ0ꢅꢆꢚꢍꢒ
ꢌꢀ
ꢂ
ꢒ
:ꢁ6ꢗꢉ"ꢜ#
9ꢁ<!ꢉ"ꢜ#
ꢗꢁꢘ!
ꢗꢁ ꢗ
M
M
ꢗꢁ!ꢗ
ꢀꢁꢘꢙ
0
)ꢈꢈꢍꢔꢓꢃꢆꢍ
)ꢈꢈꢍꢉꢛꢆꢚꢏꢅ
0ꢅꢊꢋꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
0ꢅꢊꢋꢉ;ꢃꢋꢍꢒ
ꢕꢈꢏꢋꢉꢂꢓꢊꢑꢍꢉꢛꢆꢚꢏꢅꢉ%ꢈꢔ
ꢕꢈꢏꢋꢉꢂꢓꢊꢑꢍꢉꢛꢆꢚꢏꢅꢉ"ꢈꢍꢍꢈꢄ
0ꢀ
ꢀ
ꢀꢁꢗ ꢉ1ꢌ)
ꢗꢞ
ꢗꢁꢀꢙ
ꢗꢁ:ꢀ
!ꢞ
M
M
M
M
M
9ꢞ
ꢎ
5
ꢁ
ꢗꢁꢘ!
ꢗꢁ!ꢀ
ꢀ!ꢞ
ꢂ
!ꢞ
ꢀ!ꢞ
ꢛꢔꢊꢃꢉꢜ
ꢀꢁ ,ꢃꢆꢉꢀꢉ'ꢃꢇꢐꢊꢏꢉꢃꢆꢋꢅꢖꢉꢑꢅꢊꢍꢐꢓꢅꢉꢄꢊ&ꢉ'ꢊꢓ&+ꢉ5ꢐꢍꢉꢄꢐꢇꢍꢉ5ꢅꢉꢏꢈꢎꢊꢍꢅꢋꢉ(ꢃꢍꢒꢃꢆꢉꢍꢒꢅꢉꢒꢊꢍꢎꢒꢅꢋꢉꢊꢓꢅꢊꢁ
ꢘꢁ ꢟꢉꢜꢃꢚꢆꢃꢑꢃꢎꢊꢆꢍꢉ#ꢒꢊꢓꢊꢎꢍꢅꢓꢃꢇꢍꢃꢎꢁ
:ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢇꢉꢂꢉꢊꢆꢋꢉꢌꢀꢉꢋꢈꢉꢆꢈꢍꢉꢃꢆꢎꢏꢐꢋꢅꢉꢄꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢁꢉꢕꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢉꢇꢒꢊꢏꢏꢉꢆꢈꢍꢉꢅꢖꢎꢅꢅꢋꢉꢗꢁꢀ!ꢉꢄꢄꢉꢔꢅꢓꢉꢇꢃꢋꢅꢁ
ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢃꢆꢚꢉꢊꢆꢋꢉꢍꢈꢏꢅꢓꢊꢆꢎꢃꢆꢚꢉꢔꢅꢓꢉꢛꢜꢕꢌꢉꢝꢀ ꢁ!ꢕꢁ
"ꢜ#$ "ꢊꢇꢃꢎꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆꢁꢉ%ꢒꢅꢈꢓꢅꢍꢃꢎꢊꢏꢏ&ꢉꢅꢖꢊꢎꢍꢉ'ꢊꢏꢐꢅꢉꢇꢒꢈ(ꢆꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅꢇꢁ
1ꢌ)$ 1ꢅꢑꢅꢓꢅꢆꢎꢅꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆ+ꢉꢐꢇꢐꢊꢏꢏ&ꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅ+ꢉꢑꢈꢓꢉꢃꢆꢑꢈꢓꢄꢊꢍꢃꢈꢆꢉꢔꢐꢓꢔꢈꢇꢅꢇꢉꢈꢆꢏ&ꢁ
ꢕꢃꢎꢓꢈꢎꢒꢃꢔ %ꢅꢎꢒꢆꢈꢏꢈꢚ& ꢂꢓꢊ(ꢃꢆꢚ #ꢗ >ꢗ<!"
© 2008 Microchip Technology Inc.
DS22041B-page 27
MCP6031/2/3/4
01ꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢒ2ꢋꢑꢆꢍ2ꢓꢋꢑ#ꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢕꢍꢒꢖꢆMꢆ1*1ꢆꢎꢎꢆ,ꢔꢅ-ꢆꢗꢒꢍꢍꢏꢇꢚ
ꢛꢔꢊꢃꢜ )ꢈꢓꢉꢍꢒꢅꢉꢄꢈꢇꢍꢉꢎꢐꢓꢓꢅꢆꢍꢉꢔꢊꢎ*ꢊꢚꢅꢉꢋꢓꢊ(ꢃꢆꢚꢇ+ꢉꢔꢏꢅꢊꢇꢅꢉꢇꢅꢅꢉꢍꢒꢅꢉꢕꢃꢎꢓꢈꢎꢒꢃꢔꢉ,ꢊꢎ*ꢊꢚꢃꢆꢚꢉꢜꢔꢅꢎꢃꢑꢃꢎꢊꢍꢃꢈꢆꢉꢏꢈꢎꢊꢍꢅꢋꢉꢊꢍꢉ
ꢒꢍꢍꢔ$--(((ꢁꢄꢃꢎꢓꢈꢎꢒꢃꢔꢁꢎꢈꢄ-ꢔꢊꢎ*ꢊꢚꢃꢆꢚ
D
N
E
E1
NOTE 1
1
2
e
b
c
φ
A2
A
A1
L
L1
.ꢆꢃꢍꢇ
ꢕ/00/ꢕꢌ%ꢌ1ꢜ
ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢉ0ꢃꢄꢃꢍꢇ
ꢕ/2
23ꢕ
ꢕꢛ4
2ꢐꢄ5ꢅꢓꢉꢈꢑꢉ,ꢃꢆꢇ
,ꢃꢍꢎꢒ
2
ꢅ
ꢀ
ꢗꢁ<!ꢉ"ꢜ#
3'ꢅꢓꢊꢏꢏꢉ7ꢅꢃꢚꢒꢍ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
ꢜꢍꢊꢆꢋꢈꢑꢑꢉ
3'ꢅꢓꢊꢏꢏꢉ;ꢃꢋꢍꢒ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ;ꢃꢋꢍꢒ
ꢕꢈꢏꢋꢅꢋꢉ,ꢊꢎ*ꢊꢚꢅꢉ0ꢅꢆꢚꢍꢒ
)ꢈꢈꢍꢉ0ꢅꢆꢚꢍꢒ
ꢛ
M
ꢗꢁ9ꢗ
ꢗꢁꢗ!
M
ꢀꢁꢗꢗ
M
<ꢁ ꢗꢉ"ꢜ#
ꢁ ꢗ
!ꢁꢗꢗ
ꢗꢁ<ꢗ
ꢀꢁꢘꢗ
ꢀꢁꢗ!
ꢗꢁꢀ!
ꢛꢘ
ꢛꢀ
ꢌ
ꢌꢀ
ꢂ
ꢁ:ꢗ
ꢁ6ꢗ
ꢗꢁ !
ꢁ!ꢗ
!ꢁꢀꢗ
ꢗꢁꢙ!
0
)ꢈꢈꢍꢔꢓꢃꢆꢍ
)ꢈꢈꢍꢉꢛꢆꢚꢏꢅ
0ꢅꢊꢋꢉ%ꢒꢃꢎ*ꢆꢅꢇꢇ
0ꢅꢊꢋꢉ;ꢃꢋꢍꢒ
0ꢀ
ꢀ
ꢀꢁꢗꢗꢉ1ꢌ)
ꢗꢞ
ꢗꢁꢗ6
ꢗꢁꢀ6
M
M
M
9ꢞ
ꢎ
5
ꢗꢁꢘꢗ
ꢗꢁ:ꢗ
ꢛꢔꢊꢃꢉꢜ
ꢀꢁ ,ꢃꢆꢉꢀꢉ'ꢃꢇꢐꢊꢏꢉꢃꢆꢋꢅꢖꢉꢑꢅꢊꢍꢐꢓꢅꢉꢄꢊ&ꢉ'ꢊꢓ&+ꢉ5ꢐꢍꢉꢄꢐꢇꢍꢉ5ꢅꢉꢏꢈꢎꢊꢍꢅꢋꢉ(ꢃꢍꢒꢃꢆꢉꢍꢒꢅꢉꢒꢊꢍꢎꢒꢅꢋꢉꢊꢓꢅꢊꢁ
ꢘꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢇꢉꢂꢉꢊꢆꢋꢉꢌꢀꢉꢋꢈꢉꢆꢈꢍꢉꢃꢆꢎꢏꢐꢋꢅꢉꢄꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢁꢉꢕꢈꢏꢋꢉꢑꢏꢊꢇꢒꢉꢈꢓꢉꢔꢓꢈꢍꢓꢐꢇꢃꢈꢆꢇꢉꢇꢒꢊꢏꢏꢉꢆꢈꢍꢉꢅꢖꢎꢅꢅꢋꢉꢗꢁꢀ!ꢉꢄꢄꢉꢔꢅꢓꢉꢇꢃꢋꢅꢁ
:ꢁ ꢂꢃꢄꢅꢆꢇꢃꢈꢆꢃꢆꢚꢉꢊꢆꢋꢉꢍꢈꢏꢅꢓꢊꢆꢎꢃꢆꢚꢉꢔꢅꢓꢉꢛꢜꢕꢌꢉꢝꢀ ꢁ!ꢕꢁ
"ꢜ#$ "ꢊꢇꢃꢎꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆꢁꢉ%ꢒꢅꢈꢓꢅꢍꢃꢎꢊꢏꢏ&ꢉꢅꢖꢊꢎꢍꢉ'ꢊꢏꢐꢅꢉꢇꢒꢈ(ꢆꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅꢇꢁ
1ꢌ)$ 1ꢅꢑꢅꢓꢅꢆꢎꢅꢉꢂꢃꢄꢅꢆꢇꢃꢈꢆ+ꢉꢐꢇꢐꢊꢏꢏ&ꢉ(ꢃꢍꢒꢈꢐꢍꢉꢍꢈꢏꢅꢓꢊꢆꢎꢅ+ꢉꢑꢈꢓꢉꢃꢆꢑꢈꢓꢄꢊꢍꢃꢈꢆꢉꢔꢐꢓꢔꢈꢇꢅꢇꢉꢈꢆꢏ&ꢁ
ꢕꢃꢎꢓꢈꢎꢒꢃꢔ %ꢅꢎꢒꢆꢈꢏꢈꢚ& ꢂꢓꢊ(ꢃꢆꢚ #ꢗ >ꢗ9ꢙ"
DS22041B-page 28
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
APPENDIX A: REVISION HISTORY
Revision B (March 2008)
The following is the list of modifications:
1. Added SOT-23-5 and 2x3 DFN packages.
2. Added test circuits.
3. Corrected VOS temperature drift information.
4. Added Section 4.9.3.
5. Updated Package Marking Information.
6. Updated all package outline drawings and
added package outline drawings for SOT-23-5
and 2x3 DFN packages.
7. Added Landing Pattern drawings for 2x3 DFN
and 8-lead SOIC packages.
8. Updated information in Product Identification
System for SOT-23-5 and 2x3 DFN packages.
Revision A (March 2007)
• Original Release of this Document.
© 2008 Microchip Technology Inc.
DS22041B-page 29
MCP6031/2/3/4
NOTES:
DS22041B-page 30
© 2008 Microchip Technology Inc.
MCP6031/2/3/4
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Examples:
PART NO.
Device
X
/XX
a)
b)
MCP6031-E/SN: 8LD SOIC package.
Temperature
Range
Package
MCP6031T-E/SN: Tape and Reel,
8LD SOIC package.
c)
d)
MCP6031-E/MS: 8LD MSOP package.
MCP6031T-E/MS: Tape and Reel,
8LD MSOP package.
Device:
MCP6031:
Single Op Amp
Single Op Amp (Tape and Reel)
Dual Op Amp
Dual Op Amp (Tape and Reel)
Single Op Amp with Chip Select
Single Op Amp with Chip Select
(Tape and Reel)
MCP6031T:
MCP6032:
MCP6032T:
MCP6033:
MCP6033T:
e)
f)
MCP6031-E/MC: 8LD DFN package.
MCP6031T-E/MC: Tape and Reel,
8LD DFN package.
g)
MCP6031T-E/OT: Tape and Reel,
5-LD SOT-23 package.
MCP6034:
MCP6034T:
Quad Op Amp
Quad Op Amp (Tape and Reel)
a)
b)
MCP6032-E/SN: 8LD SOIC package.
MCP6032T-E/SN: Tape and Reel,
8LD SOIC package.
Temperature Range:
Package:
E
=
-40°C to +125°C
c)
d)
MCP6032-E/MS: 8LD MSOP package
MCP6032T-E/MS: Tape and Reel
8LD MSOP package.
MC
MS
OT
SL
SN
ST
=
=
=
=
=
=
Plastic Dual Flat, No Lead, (2x3 DFN ) 8-lead **
Plastic MSOP, 8-lead
Plastic Small Outline Transistor, 5-lead *
Plastic SOIC (150 mil Body), 14-lead
Plastic SOIC, (150 mil Body), 8-lead
Plastic TSSOP (4.4mm Body), 14-lead
a)
b)
MCP6033-E/SN: 8LD SOIC package.
MCP6033T-E/SN: Tape and Reel,
8LD SOIC package.
* This package is only available on the MCP6031 device.
** These packages are only available on the MCP6031 and
MCP6033 devices.
c)
d)
MCP6033-E/MS: 8LD MSOP package.
MCP6033T-E/MS: Tape and Reel,
8LD MSOP package.
e)
f)
MCP6033-E/MC: 8LD DFN package.
MCP6033T-E/MC: Tape and Reel,
8LD DFN package.
a)
b)
MCP6034-E/SL: 14LD SOIC package.
MCP6034T-E/SL: Tape and Reel,
14LD SOIC package.
c)
d)
MCP6034-E/ST: 14LD TSSOP package.
MCP6034T-E/ST: Tape and Reel,
14LD TSSOP package.
© 2008 Microchip Technology Inc.
DS22041B-page 31
MCP6031/2/3/4
NOTES:
DS22041B-page 32
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PRO MATE, rfPIC and SmartShunt are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS22041B-page 33
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Seoul
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS22041B-page 34
© 2008 Microchip Technology Inc.
相关型号:
©2020 ICPDF网 联系我们和版权申明