15B2412ZPD [MICRODC]

15W, WIDE INPUT, DIP PACKAGE,ISOLATED REGULATED SINGLE OUTPUT DC-DC CONVERTER;


型号：	15B2412ZPD
厂家：	MICRODC POWER TECHNOLOGY CO., LTD
描述：	15W, WIDE INPUT, DIP PACKAGE,ISOLATED REGULATED SINGLE OUTPUT DC-DC CONVERTER DC-DC转换器输入元件输出元件
文件：	总3页 (文件大小：725K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

15B-ZPD Series

15W, WIDE INPUT, DIP PACKAGE,ISOLATED&REGULATED SINGLE OUTPUT DC-DC CONVERTER

SELECTION GUIDE

Input

Output

Voltage(VDC)

Efficiency

Capacitance

Order code

Voltage

Current

FEATURES

(%.Typ.)

(max,UF.)

(VDC)

(%,Typ).

Nominal

Range

◆Wide (4:1) Input Range

◆Short Circuit Protection(automatic recovery)

◆1500VDC Isolation

15B1203ZPD

15B1205ZPD

15B1212ZPD

15B1215ZPD

15B1224ZPD

15B2403ZPD

15B2405ZPD

15B2412ZPD

15B2415ZPD

15B2424ZPD

15B4803ZPD

15B4805ZPD

15B4812ZPD

15B4815ZPD

15B4824ZPD

9-18

3.3

3000

1250

1000

675

19000

10300

3340

1100

900

9-18

3.3

◆Operating Temperature: -40℃～﹢85℃

◆Six sided metal shielding

◆Over Voltage protection

◆Internal SMD construction

◆RoHS Compliance

9-18

18-36

36-75

3000

1250

1000

675

19500

10200

3300

1100

900

3.3

3000

1250

1000

675

19500

10200

3300

1100

900

◆Industry Standard Pin Out

◆MTBF>1000Khours

MODEL SELECTION

①

②

③

④

⑤

⑥

COMMON SPECIFICATIONS

15 B 24 15 Z PD

Parameter

Storage humidity

Operating temperature

Storage temperature

Lead temperature

Case material

Conditions

Min. Typ. Max. Units

①Rated Power ②Product Series

③Input Voltage ④Output Voltage

⑤Wide (4:1) Input Range⑥DIP Package Style

℃

-40

-55

105

300

1.5mm from case for 10 seconds

APPLICATIONS

Steel,nickel coated, copper

The 15B-ZPD Series are specially

designed for applications where a wide range

input voltage power supplies are isolated from

the input power supply in a distributed power

supply system on a circuit board.

Tested for1 minute and 1mA max

Isolation voltage

Isolation resistance

Isolation Capacitance

MTBF

1500

1000

VDC

MΩ

100KHz/1V

K hours

Weight

These products apply to:

1)Where the voltage of the input power

supply is wide range (Voltage range≤4:1);

2)Where isolation is necessary between

input and output (Isolation voltage≤1500VDC);

3)Where the regulation of the Output voltage

and the output ripple noise are demanded.

INPUT SPECIFICATIONS

Parameter

Conditions

Min.

Typ. Max. Units

Start voltage/Under

12V input models

24V input models

48V input models

8.6/8.1

17.5/16

34/32

8.8/8.

17.8/1

35/33

9/8.5

18/17

36/34

VDC

voltage shutdown

Start up time

Input filter

Method of Remote

Off

3.5-40VDC or open circuit

0-1.2VDC

MICRODC RESERVES THE COPYRIGHT

(Reference point:GND)

http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646

Page 1 of 3

15B-ZPD Series

TEMPERATURE CHARACTERISTICS

TYPICAL CHARACTERISTICS

Parameter

Conditions

Min.

Typ.

Max.

Units

Temperature Derating Graph

Output voltage accuracy

Refer to recommended circuit

±1

±3

Over load protection

Output Short Circuit

Load regulation

Input voltage range

120

130

150

Hiccup,automatics recovery

From 10% to 100% load

±0.5

±1

Trim

±10%V0

VDC

%/℃

Temperature drift (Vout)

Line regulation

0.02

Input voltage from low to high

Tested under 20MHz brand

25% load change

±0.2

±0.5

150

300

±5

Ripple＆Noise

Transient recovery time

Transient peak deviation

200

±3

±2

RECOMMENDED CIRCUIT

3.3V

3.63

5.5

4.29

6.5

VDC

Output Graph

Over voltage protection

12V

15V

24V

13.2

16.5

26.4

15.6

19.5

31.2

Note:

1. All specifications are measured at TA=25°C, humidity<75%, nominal input voltage and rated output load

unless otherwise specified.

2. The CTRL control pin voltage is referenced to GND.

In order to obtain better performance for the DC/DC

models.it’s recommended that use input and output

filters as Fig.1 shown.

3. Typical efficiency value at nominal input voltage and full load.

4. Capacitor MAX load tested at nominal input voltage and constant resistive load.

5. Refer to the diagram of Output Voltage trim up/down for trim applications.

6. The products cannot be used in parallel and in plug and play.

L:12uH

C:100uF/100V

Case material

DERATING＆EFFICIENCY CURVE

OUTPUT VOLTAGE TRIM

Requirement on output load

Output Graph

In order to ensure the product operate efficiently and reliably,in addition to a

max load(namely full load), a minimum load is specified for this kind of

DC/DC converter.Make sure the specified range of input voltage is not

exceeded,the minimum output load no less than 10% load.If the actual

load is less than the specified minimum load, the output ripple may increase

sharply while its efficiency and reliability will reduce greatly.If the actual

output power is very small,please add an appropriate resistor as extra

loading,or contact our company for other lower output power products.

Curve of Efficiency VS input Voltage 15B2424ZPD

Curve of Efficiency VS output load WRB2424YD-30W

No parallel connection or plug and play

http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646

Page 2 of 3

15B-ZPD Series

OUTLINE DIMENSIONS ＆ FOOTPRINT DETAILS

MECHANICAL DIMENSIONS

RECOMMENDED FOOTPRINT

Note:

Unit:mm[inch]

Pin diameter:1.00mm[0.039inch]

Pin diameter tolerances:±0.05mm[±0.002inch]

General tolerances:±0.25mm[±0.010inch]

RECOMMENDED FOOTPRINT

Top view grid:2.54mm(0.1inch)

diameter:1.50mm(0.059inch)

FOOTPRINT DETAILS

TUBE OUTLINE DIMENSIONS

Single

Vin

GND

Ctrl

Trim

+Vo

Note: The CTRL control pin voltage is referenced to GND

When the environment temperature is higher than 71℃, the

product output power should be less then 60% of the rated

power.

No parallel connection or plug and play.

Use dual output simultaneously,forbid pening output pin (0V)

to use as single output.

Note:

Unit :mm[inch]

General tolerances:±0.250mm[±0.010inch]

Note:

1. The CTRL control pin voltage is referenced to GND.

2. Typical efficiency value at nominal input voltage and full load.

3. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.

4. In this data sheet, all the test methods of indications are based on corporate standards.

5. Capacitor MAX load tested at nominal input voltage and constant resistive load.

http://www.microdc.cn Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646

Page 3 of 3

相关型号：