MTFDDAT064MAM-1J11AB [MICRON]
C400v mSATA NAND Flash SSD;型号: | MTFDDAT064MAM-1J11AB |
厂家: | MICRON TECHNOLOGY |
描述: | C400v mSATA NAND Flash SSD |
文件: | 总30页 (文件大小:327K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
C400v mSATA NAND Flash SSD
Features
C400v mSATA NAND Flash SSD
MTFDDAT032MAM, MTFDDAT064MAM
• Reliability
Features
– MTTF: 1.2 million device hours3
– Static and dynamic wear leveling
– Uncorrectable bit error rate (UBER): <1 sector
per 1015 bits read
• Micron® 25nm MLC NAND Flash
• RoHS-compliant package
• SATA 6 Gb/s interface
• ATA modes supported
– PIO mode 3, 4
• Low power consumption
– <150mW TYP4
– Multiword DMA mode 0, 1, 2
– Ultra DMA mode 0, 1, 2, 3, 4, 5
• Industry-standard, 512-byte sector size support
• Native command queuing support with 32-com-
mand slot support
• ATA-8 ACS2 command set compliant
• ATA security feature command set and password
login support
• Endurance: Total bytes written (TBW) – 36TB
• Capacity5 (unformatted): 32GB, 64GB
• Mechanical – 5mm height
– mSATA connector: 3.3V ±5%
– Caseless design: 50.80mm x 29.85mm x 3.75mm
– Weight: 10g (MAX)
• Field-updateable firmware
• Operating temperature
– Commercial (0°C to +70°C)6
• Secure erase (data page) command set: fast and se-
cure erase
1. Typical I/O performance numbers as meas-
ured using Iometer with a queue depth of
32 and write cache enabled.
Notes:
• Self-monitoring, analysis, and reporting technology
(SMART) command set
• Performance1, 2
2. 4K transfers used for READ/WRITE latency
values.
3. The product achieves a mean time between
failure (MTTF) based on population statis-
tics not relevant to individual units.
4. Active power measured during execution of
MobileMark® 2007 with DIPM (device-initi-
ated power management) enabled.
– Sequential 128k READ: up to 500 MB/s
– Sequential 128k WRITE: up to 95 MB/s
– Random 4k READ: up to 45,000 IOPS
– Random 4k WRITE: up to 20,000 IOPS
– PCMark® Vantage (HDD test suite score): up to
65,000
– READ/WRITE latency: 55µs (TYP)
5. 1GB = 1 billion bytes; formatted capacity is
less.
6. Drive case temperature.
Warranty: Contact your Micron sales representative
for further information regarding the product,
including product warranties.
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
1
© 2011 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
C400v mSATA NAND Flash SSD
Features
Part Numbering Information
Micron’s RealSSD™ C400 SSD is available in different configurations and densities. Visit www.micron.com for a
list of valid part numbers.
Figure 1: Part Number Chart
MT FD
D
AT 032 M AM - 1
J
x
x
xx
ES
Production Status
Blank = Production
Micron Technology
ES = Engineering sample
Product Family
FD = Flash drive
Operating Temperature Range
Blank = Commercial (0°C to +70°C)
Drive Interface
D = SATA 6.0 Gb/s
Hardware Feature Set
Blank = Null
Drive Form Factor
AT = mSATA
AA = Contact factory
AB = Contact factory
AC = Contact factory
Drive Density
032 = 32GB
Firmware Feature Set
Blank = Null
064 = 64GB
1 = Contact factory
2 = Contact factory
NAND Flash Type
M = MLC
BOM Revision
For example:
1 = 1st generation
Product Family
AM = C400
Sector Size
1 = 512-byte
NAND Flash Component
J = 32Gb, MLC, x8, 3.3V (25nm)
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
General Description
General Description
Micron’s RealSSD solid state drive (SSD) uses a single-chip controller with a SATA inter-
face on the system side and n-channels of Micron NAND Flash internally. Packaged in
an JEDEC-standard mSATA form factor, the SSD integrates easily in existing storage in-
frastructures.
The SSD is designed to use the SATA interface efficiently during both READs and
WRITEs while delivering bandwidth-focused performance. SSD technology enables en-
hanced boot times, faster application load times, reduced power consumption, and ex-
tended reliability.
Figure 2: Functional Block Diagram
NAND
NAND
NAND
SSD
controller
SATA
NAND
NAND
DRAM
buffer
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
3
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Logical Block Address Configuration
Logical Block Address Configuration
The drive is set to report the number of logical block addresses (LBA) that will ensure
sufficient storage space for the specified density. Standard LBA settings, based on the
IDEMA standard (LBA1-02), are shown below.
Table 1: Standard LBA Settings
Total LBA
Hexadecimal
Max LBA
Hexadecimal
User Available Bytes
(Unformatted)
32,017,047,552
Drive Size
32GB
Decimal
62,533,296
125,045,424
Decimal
62,533,295
125,045,423
3BA2EB0
7740AB0
3BA2EAF
7740AAF
64GB
64,023,257,088
Physical Configuration
Table 2: mSATA Dimensions and Weight
Value
Unit
Width
29.85
50.80
10
mm (NOM)
mm (NOM)
g (MAX)
Length
Unit weight
Height
3.75
mm (MAX)
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
4
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Interface Connectors
Interface Connectors
Figure 3: SSD Interface Connections
Primary side
Secondary side
P1
P17
P15
P51
P52
P18
P16
P2
Table 3: Signal Assignments
Primary Side
Secondary Side
Pin #
1
Signal Name
Reserved
Reserved
Reserved
Reserved
GND
Description
No connect
No connect
No connect
No connect
Ground
Pin #
Signal Name
3V3
Description
+3.3V
2
3
4
GND
Ground
5
6
1V5
No connect
No connect
No connect
No connect
No connect
No connect
Ground
7
8
Reserved
Reserved
Reserved
Reserved
Reserved
GND
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
Reserved
Reserved
GND
No connect
No connect
Ground
Reserved
Reserved
GND
No connect
No connect
Ground
Reserved
Reserved
3V3
No connect
No connect
+3.3V
+B
Differential signal pair +B
and -B
-B
GND
Ground
GND
Ground
Ground
1V5
No connect
Two-wire interface
GND
TWI
-A
Differential signal pair +A
and -A
TWI
+A
GND
Ground
GND
Ground
Reserved
Reserved
GND
No connect
No connect
Ground
GND
Ground
3V3
+3.3V
3V3
+3.3V
Reserved
Reserved
Reserved
1V5
No connect
No connect
No connect
No connect
Ground
NC
No connect
No connect
No connect
Drive activity LED
Presence detection
Optional
Optional
DA/DSS
Presence
GND
3V3
+3.3V
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
5
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Performance
Performance
Measured performance can vary for a number of reasons. The major factors affecting
drive performance are the density of the drive and the interface of the host. Additional-
ly, overall system performance can affect the measured drive performance. When com-
paring drives, it is recommended that all system variables are the same, and only the
drive being tested varies.
Performance numbers will vary depending on the host system configuration.
Table 4: Drive Performance
Density
Interface Speed
32GB
6 Gb/s
440
64GB
6 Gb/s
500
Unit
MB/s
MB/s
IOPS
Sequential read (128k transfer)
Sequential write (128k transfer)
Random read (4k transfer)
Random write (4k transfer)
Read latency
50
95
45,000
15,000
55
45,000
20,000
55
IOPS
µs
Write latency
55
55
µs
PCMark vantage
55,000
65,000
HDD score
1. Typical I/O performance numbers as measured using IOMeter with a queue depth of 32
and write cache enabled.
Notes:
2. IOMeter measurements are performed on an 8GB span.
3. 4k transfers used for READ/WRITE latency values.
4. System variations may affect measured results.
5. Performance numbers are indicative of C400 firmware version 0009 and newer.
Cache Drive Performance
Micron's RealSSD C400 mSATA drive has been tested with Intel® Smart Response Tech-
nology and has passed the performance benchmarks for the 'While Using' portion of
the responsiveness requirements provided in the 2012 Ultrabook™ Definition.
Table 5: PCMark Vantage Scores (with 7200 rpm Notebook HDD)
Overall HDD
Suite Score
Windows Movie
Maker Score
C400 RealSSD Devices
32GB as cache
24,000
56,500
80 MB/s
64GB as cache
115 MB/s
1. Disclaimer: Intel Smart Response Technology requires a select Intel® processor, enabled
chipset, Intel® Rapid Storage Technology software, and a properly configured storage
solution (HDD + small SSD). Depending on system configuration, results may vary. Con-
tact your system manufacturer for more information.
Note:
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
6
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Reliability
Reliability
Micron’s SSDs incorporate advanced technology for defect and error management.
They use various combinations of hardware-based error correction algorithms and
firmware-based static and dynamic wear-leveling algorithms.
Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is de-
fined as data that is reported as successfully programmed to the SSD but when it is read
out of the SSD, the data differs from what was programmed.
Table 6: Uncorrectable Bit Error Rate
Uncorrectable Bit Error Rate
Operation
<1 sector per 1015 bits read
READ
Mean Time to Failure
Mean time to failure (MTTF) for the SSD can be predicted based on the component reli-
ability data using the methods referenced in the Telcordia SR-332 reliability prediction
procedures for electronic equipment.
Table 7: MTTF
Density
32GB
MTTF (Operating Hours)1
1.2 million
64GB
1.2 million
1. The product achieves a mean time to failure (MTTF) of 1.2 million hours, based on popu-
lation statistics not relevant to individual units.
Note:
Endurance
Endurance for the SSD can be predicted based on the usage conditions applied to the
device, the internal NAND component cycles, the write amplification factor, and the
wear-leveling efficiency of the drive. The table below shows the drive lifetime for each
SSD density based on predefined usage conditions.
Table 8: Drive Lifetime
Density
32GB
Drive Lifetime (Total Bytes Written)
36TB
36TB
64GB
1. Total bytes written calculated with the drive 90% full.
Notes:
2. Access patterns are 50% sequential and 50% random and consist of the following: 5%
are 4k; 5% are 8k; 10% are 16k; 10% are 32k; 35% are 64K; and 35% are 128k.
3. GB/day can be calculated by dividing the total bytes written value by (365 × number of
years). For example: 36 TB/5 years/365 days = 20 GB/day for 5 years.
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
7
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Electrical Characteristics
Electrical Characteristics
Stresses greater than those listed may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at these or any other condi-
tions above those indicated in the operational sections of this specification is not im-
plied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
Table 9: mSATA Power Consumption
Sequential Write/Read Maximum
(128k transfer)
Density
32GB
Idle Average
Active Average
Unit
<65
<65
150
150
1900
2400
1600
1700
64GB
mW
1. Data taken at 25°C using a 6 Gb/s SATA interface.
Notes:
2. Active average power measured while running MobileMark® 2007 Productivity Suite.
3. DIPM (device-initiated power management) enabled.
4. Sequential power measured in IOMETER MAX with 128KB transfer size.
Table 10: Maximum Ratings
Parameter/Condition
Voltage input
Symbol
3V3
Min
3.14
0
Max
3.46
70
Unit
V
Operating temperature
Non-operating temperature
Rate of temperature change
Relative humidity (non-condensing)
TC
°C
–40
–
85
°C
20
°C/hour
%
5
95
1. Temperature is best measured with a thermocouple attached to the center point of the
drive controller ASIC package. This is the larger package closest to the interface connec-
tor on the primary side. Refer to the Package Dimensions for details.
Notes:
2. Supply voltage slew rate during asynchronous power-down should follow a slope of no
steeper than 60 mV/ms.
3. Power-off sequence: When the Micron C400 SSD is shut down, the ATA STANDBY IMME-
DIATE (STBI) command should be the last command sent by the host and acknowledged
by the SSD. Failure to follow this process could result in a longer than normal time-to-
ready(TTR) during the subsequent power-on sequence. TTR is the time from power-on
to drive ready to accept SATA commands.
Table 11: Shock and Vibration
Parameter/Condition
Operating shock
Specification
1500 G/1.0ms
Operating vibration
2–500Hz at 3.1G
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
8
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Device ID
Table 12: Identity Device
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
General configuration bit-significant information
0 = ATA device
0
15
14–8
7
F
X
F
0b
0000100b
0b
Retired
1 = removable media device
6
F
1b
Obsolete
5–3
2
X
V
X
F
000b
Retired
0b
Response incomplete
1
0b
Retired
0
0b
Reserved
1
2
3FFFh
C837h
0010h
0000h 0000h
003Fh
0000h 0000h
0000h
varies
Obsolete
F
F
Specific configuration
3
Obsolete
4
F
Retired
6
F
Obsolete
7
(O)V
( )X
(M)F
( )X
Reserved for assignment by the CompactFlash™ Association
9
Retired
10
20
Serial number (20 ASCII characters)
Retired/Obsolete
0000h 0000h
0000h
23
27
47
(M)F
(M)F
F
varies
varies
80h
Firmware revision (8 ASCII characters)
Model number (40 ASCII characters)
80h
15–8
7–0
F
10h
00h = Reserved
01h-FFh = Maximum number of logical sectors that shall be
transferred per DRQ data block on READ/WRITE MULTIPLE
commands
48
Trusted Computing feature set options
Shall be cleared to zero
15
14
F
F
F
F
0b
1b
Shall be set to one
13–1
0
0000000000000b Reserved for the Trusted Computing Group
0b
1=Trusted Computing feature set is support
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
9
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
49
Capabilities
15–14
13
F
F
00b
1b
Reserved for the IDENTIFY PACKET DEVICE command.
1 = Standby timer values as specified in this standard are
supported
0 = Standby timer values shall be managed by the device
Reserved for the IDENTIFY PACKET DEVICE command.
1= IORDY supported
12
11
F
F
0b
1b
0 = IORDY may be supported
1 = IORDY may be disabled
1 = LBA supported
10
9
F
1b
1b
8
F
F
1b
1 = DMA supported.
7–0
00000000b
Retired
50
Capabilities
15
14
13–2
1
F
F
F
X
F
0b
1b
Shall be cleared to zero
Shall be set to one
000000000000b Reserved
0b
1b
Obsolete
0
Shall be set to one to indicate a vendor specific standby tim-
er value minimum.
51
53
( )X
F
0000h 0000h
Obsolete
15–3
2
0000000000000b Reserved
F
1b
1b
1b
1 = the fields reported in word 88 are valid
0 = the fields reported in word 88 are not valid
1
0
F
1 = the fields reported in words (70:64) are valid
0 = the fields reported in words (70:64) are not valid
X
Obsolete
Obsolete
54
59
()X
3FFFh 0010h
003Fh FC10h
00FBh
15
14
F
F
0b
0b
1 = The BLOCK ERASE EXT command is supported
1 = The OVERWRITE EXT command is supported
1 = The CRYPTO SCRAMBLE EXT command is supported
1 = The Sanitize feature set is supported
Reserved
13
F
0b
12
F
0b
11–9
8
F
000b
1b
V
V
1 = Multiple sector setting is valid
7–0
00000001b
xxh = Current setting for number of logical sectors that shall
be transferred per DRQ data block on READ/WRITE MULTI-
PLE commands
60
M(F)
Varies by capacity Total number of user addressable logical sectors
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2011 Micron Technology, Inc. All rights reserved.
10
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
62
Bit(s)
Setting
Default Value Description
()X
F
0000h
00000b
0b
Obsolete
Reserved
63
15–11
10
V
1 = Multiword DMA mode 2 is selected
0 = Multiword DMA mode 2 is not selected
9
8
V
V
0b
0b
1 = Multiword DMA mode 1 is selected
0 = Multiword DMA mode 1 is not selected
1 = Multiword DMA mode 0 is selected
0 = Multiword DMA mode 0 is not selected
7–3
2
F
F
F
F
F
F
F
0000b
1b
Reserved
1 = Multiword DMA mode 2 and below are supported
1 = Multiword DMA mode 1 and below are supported
1 = Multiword DMA mode 0 is supported
Reserved
1
1b
0
1b
64
15–8
7–0
0
03h
0078h
PIO modes supported
65
66
Minimum Multiword DMA transfer cycle time per word
Cycle time in nanoseconds
F
0078h
Manufacturer's recommended Multiword DMA transfer cy-
cle time
Cycle time in nanoseconds
67
68
69
F
F
0078h
0078h
Minimum PIO transfer cycle time without flow control
Cycle time in nanoseconds
Minimum PIO transfer cycle time with IORDY flow control
Cycle time in nanoseconds
F
F
F
F
Additional Supported
15
14
13
0b
1b
0b
1 = CFast Specification Support
1 = Deterministic read after Trim is supported
1 = Long Physical Sector Alignment Error Reporting Control
is supported
12
F
0b
1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE
CONFIGURATION SET DMA are supported
11
10
9
F
F
F
0b
0b
0b
1 = READ BUFFER DMA is supported
1 = WRITE BUFFER DMA is supported
1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA
are supported
8
7
F
F
F
F
F
F
0b
0b
1 = DOWNLOAD MICROCODE DMA is supported
Reserved for IEEE-1667
6
0b
1 = Optional ATA device 28-bit commands supported
1 = Read zero after Trim is supported
Reserved
5
0b
4–0
00000b
0000h
70
Reserved
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
11
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
71
F
0000h 0000h
0000h 0000h
Reserved for the IDENTIFY PACKET DEVICE command
75
76
Queue depth
15–5
4–0
F
F
00000000000b Reserved
11111b
Maximum queue depth - 1
Serial ATA Capabilities
15–13
12
F
F
F
F
F
000b
1b
Reserved
Supports Native Command Queuing priority information
Supports Unload while NCQ commands outstanding
Supports Phy event counters
11
0b
10
1b
9
1b
Supports receipt of host initiated interface power manage-
ment requests
NOTE: HIPM is disabled (bit 9 = 0) for firmware versions
000G and newer
8
7–4
3
F
F
F
F
F
F
1b
0000b
1b
Supports native Command Queueing
Reserved for future Serial ATA signaling speed grades
1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s)
1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s)
1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s)
Reserved (set to 0)
2
1b
1
1b
0
0b
77
Serial ATA Additional capabilities
15–6
5
F
F
0000000000b
Reserved for future Serial ATA definition
Supports NCQ Queue Management Command
Supports NCQ Streaming
0b
0b
4
F
3–1
V
010b
Coded value indicating current negotiated Serial ATA signal
speed
0
F
0b
Shall be cleared to zero
78
Serial ATA features Supported
Reserved
15–7
F
F
F
F
F
F
F
F
000000000b
6
5
4
3
2
1
0
1b
0b
0b
1b
1b
0b
0b
1 = supports software settings preservation
Reserved
1 = supports in-order data delivery
1 = supports dev initiate interface power management
1 = supports DMA Setup Auto-Activate optimization
1 = supports non-zero buffer offsets in DMA Setup FIS
Reserved (set to 0)
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
12
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
Serial ATA features Enabled
Reserved
79
15–7
V
V
V
V
V
V
V
V
000000000b
6
5
4
3
2
1
0
1b
0b
0b
0b
0b
0b
0b
1 = software settings preservation enabled
1 = Asynchronous notification enabled
1 = in-order data delivery enabled
1 = device initiating interface power management enabled
1 = DMA Setup Auto-Activate optimization enabled
1 = non-zero buffer offsets in DMA Setup FIS enabled
Reserved (set to 0)
80
Major revision number
15–10
F
F
F
F
F
F
F
F
S
S
F
F
000000b
1b
Reserved
9
8
7
6
5
4
3
2
1
0
1 = supports ATA8-ACS2
1b
1 = supports ATA8-ACS
1b
1 = supports ATA/ATAPI-7
1 = supports ATA/ATAPI-6
1 = supports ATA/ATAPI-5
1 = supports ATA/ATAPI-4
Obsolete
1b
1b
1b
1b
0b
Obsolete
0b
Obsolete
0b
Reserved
81
0028h
Minor revision number
0028h = ATA8-ACS version 6
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
13
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
Command set supported
Obsolete
82
15
14
13
12
11
10
9
X
F
F
F
X
F
F
F
F
F
F
F
0b
1b
1b
1b
0b
1b
0b
0b
0b
1b
1b
0b
1 = NOP command supported
1 = READ BUFFER command supported
1 = WRITE BUFFER command supported
Obsolete
1 = Host Protected Area feature set supported
1 = DEVICE RESET command supported
1 = SERVICE interrupt supported
1 = release interrupt supported
1 = read look-ahead supported
1 = write cache supported
8
7
6
5
4
Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3
2
1
0
F
F
F
F
1b
0b
1b
1b
1 = mandatory Power Management feature set supported
Obsolete
1 = Security feature set supported
1 = SMART feature set supported
83
Command set supported
15
14
13
12
11
10
9
F
F
F
F
F
F
F
F
F
F
0b
1b
1b
1b
1b
1b
0b
1b
0b
0b
Shall be cleared to zero
Shall be set to one
1 = FLUSH CACHE EXT command supported
1 = mandatory FLUSH CACHE command supported
1 = Device Configuration Overlay feature set supported
1 = 48-bit Address feature set supported
1 = Automatic Acoustic Management feature set supported
1 = SET MAX security extension supported
See Address Offset Reserved Area Boot INCITS TR27:2001
8
7
6
1 = SET FEATURES subcommand required to spin-up after
power-up
5
4
3
2
1
0
F
F
F
F
F
F
0b
0b
1b
0b
0b
1b
1 = Power-Up In Standby feature set supported
Obsolete
1 = Advanced Power Management feature set supported
1 = CFA feature set supported
1 = READ/WRITE DMA QUEUED supported
1 = DOWNLOAD MICROCODE command supported
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
14
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
Command set/feature supported extension
Shall be cleared to zero
84
15
14
13
12
11
10–9
8
F
F
F
F
F
F
F
F
F
0b
1b
1b
0b
0b
00b
1b
0b
1b
Shall be set to one
1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
Reserved for technical report INCITS TR-37-2004 (TLC)
Reserved for technical report INCITS TR-37-2004 (TLC)
Obsolete
1 = 64-bit Word wide name supported
1 = WRITE DMA QUEUED FUA EXT command supported
7
6
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5
4
3
F
F
F
1b
0b
0b
1 = General Purpose Logging feature set supported
1 = Streaming feature set supported
1 = Media Card Pass Through Command feature set suppor-
ted
2
1
0
F
F
F
0b
1b
1b
1 = Media serial number supported
1 = SMART self-test supported
1 = SMART error logging supported
Command set/feature enabled.
Obsolete
85
15
14
13
12
11
10
9
X
F
0b
1b
1b
1b
0b
1b
0b
0b
0b
1b
1b
0b
1 = NOP command supported
1 = READ BUFFER command supported
1 = WRITE BUFFER command supported
Obsolete
F
F
X
V
F
1 = Host Protected Area feature set enabled
1 = DEVICE RESET command supported
1 = SERVICE interrupt enabled
1 = release interrupt enabled
1 = look-ahead enabled
8
V
V
V
V
F
7
6
5
1 = write cache enabled
4
Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3
2
1
0
F
F
1b
0b
0b
1b
Power Management feature set is enabled
Obsolete
V
V
1 = Security Mode feature set enabled
1 = SMART feature set enabled
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
15
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
Command set/feature enabled.
1 = Words 120-119 are valid
86
15
14
13
12
11
10
9
1b
0b
1b
1b
1b
1b
0b
0b
0b
F
F
F
F
F
V
F
F
1 = Reserved
1 = FLUSH CACHE EXT command supported
1 = FLUSH CACHE command supported
1 = Device Configuration Overlay supported
1 = 48-bit Address features set supported
1 = Automatic Acoustic Management feature set enabled
1 = SET MAX security enabled by SET MAX SET PASSWORD
8
7
Reserved for address Offset Reserved Area Boot, INCITS
TR27:2001
6
F
0b
1 = SET FEATURES subcommand required to spin-up after
power-up
5
4
3
2
1
0
V
V
V
F
0b
0b
1b
0b
0b
1b
1 = Power-Up In Standby feature set enabled
Obsolete
1 = Advanced Power Management feature set enabled
1 = CFA feature set supported
F
1 = READ/WRITE DMA QUEUED command supported
1 = DOWNLOAD MICROCODE command supported
Command set/feature enabled/supported
Shall be cleared to zero
F
87
15
14
13
12
11
10–9
8
F
F
F
V
V
F
F
F
F
0b
1b
1b
0b
0b
00b
1b
0b
1b
Shall be set to one
1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
Reserved for technical report- INCITS tr-37-2004 (TLC)
Reserved for technical report- INCITS TR-37-2004 (TLC)
Obsolete
1 = 64-bit Word wide name supported
1 = WRITE DMA QUEUED FUA EXT command supported
7
6
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5
4
3
F
V
V
1b
0b
0b
1 = General Purpose Logging feature set supported
Obsolete
1 = Media Card Pass Through Command feature set suppor-
ted
2
1
0
V
F
0b
1b
1b
1 = Media serial number is valid
1 = SMART self-test supported
1 = SMART error logging supported
F
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
16
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
88
0b
0b
0b
Ultra DMA modes
Reserved
15
14
1 = Ultra DMA mode 6 is selected
0 = Ultra DMA mode 6 is not selected
13
12
11
10
9
0b
0b
0b
0b
0b
0b
1 = Ultra DMA mode 5 is selected
0 = Ultra DMA mode 5 is not selected
1 = Ultra DMA mode 4 is selected
0 = Ultra DMA mode 4 is not selected
1 = Ultra DMA mode 3 is selected
0 = Ultra DMA mode 3 is not selected
1 = Ultra DMA mode 2 is selected
0 = Ultra DMA mode 2 is not selected
1 = Ultra DMA mode 1 is selected
0 = Ultra DMA mode 1 is not selected
8
1 = Ultra DMA mode 0 is selected
0 = Ultra DMA mode 0 is not selected
7
6
5
4
3
2
1
0
0b
0b
Reserved
1 = Ultra DMA mode 6 and below are supported
1 = Ultra DMA mode 5 and below are supported
1 = Ultra DMA mode 4 and below are supported
1 = Ultra DMA mode 3 and below are supported
1 = Ultra DMA mode 2 and below are supported
1 = Ultra DMA mode 1 and below are supported
1 = Ultra DMA mode 0 IS supported
1b
1b
1b
1b
1b
1b
89
90
91
92
(O)F
(O)F
(O)V
(O)V
0001h
0001h
00FEh
FFFEh
Time required for security erase unit completion
Time required for Enhanced security erase completion
Current advanced power management value
Master Password Revision Code
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
17
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
Shall be 0000h for SATA devices
Shall be cleared to zero
93
15
14
13
0b
0b
0b
Shall be set to one
1 = device detected CBLID-above VIH
0 = device detected CBLID-below VIL
Device 1 hardware reset result
Device 0 shall clear these bits to zero
Device 1 shall set these bits as follows:
12
11
0b
0b
Reserved
0 = Device 1 did not assert PDIAG-
1 = Device 1 asserted PDIAG-
10–9
These bits indicate how Device 1 determined the device
number:
00 = Reserved
01 = a jumper was used
10 = the CSEL signal was used
11 = some other method was used or the method is un-
known
8
0b
Shall be set to one
Device 0 hardware reset result. Device 1 shall clear these
bits to zero.
Device 0 shall set these bits as follows:
7
6
0b
0b
Reserved
0 = Device 0 does not respond when Device 1 is selected.
1 = Device 0 responds when Device 1 is selected.
5
4
0b
0b
0 = Device 0 did not detect the assertion of DASP-
1 = Device 0 detected the assertion of DASP-
0 = Device 0 did not detect the assertion of PDIAG-
1 = Device 0 detected the assertion of PDIAG-
3
0b
0 = Device 0 failed diagnostics.
1 = Device 0 passed diagnostics.
2–1
00b
These bits indicate how Device 0 determined the device
number:
00 = Reserved
01 = a jumper was used
10 = the CSEL signal was used
11 = some other method was used or the method is un-
known
0
0b
00h
Shall be set to one
94
95
15–8
7–0
F
V
Vendor's recommended acoustic management value
Current automatic acoustic management value
Stream Minimum Request Size
00h
(O)V
0000h
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
18
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
96
Bit(s)
Setting
(O)V
(O)V
(O)F
V
Default Value Description
0000h
0000h
Streaming Transfer Time - DMA
Streaming Access Latency - DMA and PIO
Streaming Performance Granularity(98-99)
97
98
0000h 0000h
100
104
105
Varies by capacity Maximum user LBA for 48-bit Address feature set
(O)V
( )F
0000h
0008h
Streaming Transfer Time - PIO
Maximum number of 512-byte blocks of LBA Range Entries
per DATA SET MANAGEMENT command
106
Physical sector size / Logical Sector Size
Shall be cleared to zero
15
14
F
F
0b
1b
Shall be set to one
13
F
0b
1 = Device has multiple logical sectors per physical sector
1 = Device Logical Sector Longer than 256 Words
Reserved
12
F
0b
11–4
3–0
F
00000000b
0000b
0000h
F
2^x logical sectors per physical sector
107
108
(O)F
Inter-seek delay for ISO-7779 acoustic testing in microsec-
onds
15–12
11–0
15–4
3–0
F
F
0101b
NAA (3-0)
000000001010b IEEE OUI (23-12)
000001110101b IEEE OUI (11-0)
109
Varies
Varies
Varies
Unique ID (35-32)
110
111
112
(M)F
(M)F
(O)F
5-0 Unique ID (31-16)
Unique ID (15-0)
0000h 0000h
0000h 0000h
Reserved for 128 bit world wide name extension to 128 bits
116
117
(O)V
(O)F
0000h
Reserved for INCITS TR-37-2004
Words per Logical Sector
0000h 0000h
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
19
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
119
Commands and feature sets supported (Continued from
words 84-82)
15
14
13–6
5
F
F
F
F
F
0b
Shall be cleared to zero
Shall be set to one
1b
00000001b
0b
Reserved
1 = Free-fall Control feature set is supported
4
1b
1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3
F
1b
1 = READ LOG DMA EXT and WRITE LOG DMA EXT com-
mands are supported
2
1
F
F
1b
1b
1 = The Write-Read-Verify feature set is supported
1 = Feature set "Disable Data Transfer After Error Detec-
tion" is supported
0
F
0b
Reserved for DDT
120
Commands and feature sets supported or enabled (Contin-
ued from words 87-85)
15
14
13–6
5
0b
Shall be cleared to zero
Shall be set to one
1b
00000000b
0b
Reserved
1 = Free-fall Control feature set is enabled
4
1b
1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3
1b
1 = The READ LOG DMA EXT and WRITE LOG DMA EXT
commands are supported
2
1
0
1b
0b
0b
1 = The WRITE UNCORRECTABLE EXT command is supported
1 = The Write-Read-Verify feature set is enabled
1= Feature set "Disable Data Transfer After Error Detection"
is enabled
0 = Feature set "Disable Data Transfer After Error Detec-
tion" is disabled
121
127
F
0000h 0000h
0000h 0000h
0000h 0000h
Reserved for expanded supported and enabled settings
(O)
0000h
Obsolete
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
20
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
128
Security status
15–9
F
V
0000000b
Reserved
8
7–6
5
0b
00b
1b
0b
0b
0b
0b
1b
Security level 0 = High, 1 = Maximum
Reserved
F
F
1 = Enhanced security erase supported
1 = Security count expired
1 = Security frozen
4
V
3
V
2
V
1 = Security locked
1
V
1 = Security enabled
0
F
1 = Security supported
129
160
( )X
Vendor specific Vendor specific
data
CFA power mode 1
15
14
13
F
F
F
0b
0b
0b
Word 160 supported
Reserved
CFA power mode 1 is required for one or more commands
implemented by the device
12
V
F
0b
CFA power mode 1 disabled
11–0
000000000000b Maximum current in ma
161
X
0000h 0000h
0000h 0000h
0000h 0000h
0000h
Reserved for assignment by the CompactFlash Association
168
169
15–4
3-0
F
F
000h
5h
Reserved
Device Nominal Form Factor
DATA SET MANAGEMENT command support
15–1
0
F
F
F
000000000000000 Reserved
b
1b
1 = the Trim bit in the DATA SET MANAGEMENT command
is supported
170
0000h 0000h
0000h 0000h
Additional Product Identifier
174
176
F
0000h 0000h
Varies
Reserved
(O)V
Current media serial number (60 ASCII characters)
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
21
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
SCT Command Transport
Vendor Specific
206
15–12
X
F
0000b
11–6
000000b
Reserved
5
4
3
2
1
0
F
1b
SCT Command Transport Data Tables supported
CT Command Transport Features Control supported
SCT Command Transport Error Recovery Control supported
SCT Command Transport Write Same supported
SCT Command Transport Long Sector Access supported
SCT Command Transport supported
Reserved for CE-ATA
F
1b
F
1b
F
1b
F
0b
1b
F
207
209
( )F
(O)
F
0000h 0000h
Alignment of logical blocks within a larger physical block
Shall be cleared to zero
15
14
0b
1b
F
Shall be set to one
13–0
F
00000000000000b 'Logical sector' offset within the first physical sector where
the first logical
sector is placed.
210
212
214
(O)V
(O)F
(O)
F
0000h 0000h
0000h 0001h
Write-Read-Verify Sector Count Mode 3 Only
Verify Sector Count Mode 2 Only
NV Cache Capabilities
15–12
11–8
7–5
4
0000b
0000b
000b
0b
NV Cache feature set version
F
NV Cache Power Mode feature set version
Reserved
F
V
1 = NV Cache feature set enabled
Reserved
3–2
1
F
00b
V
0b
1 = NV Cache Power Mode feature set enabled
1 = NV Cache Power Mode feature set supported
NV Cache Size in Logical Blocks (LSW)
NV Cache Size in Logical Blocks (MSW)
Nominal media rotation rate (ATA8-ACS 1699-D Revision 6)
0
F
0b
215
216
217
(O)V
(O)V
(M)F
0000h
0000h
0001h
NV Cache Read Transfer Speed in MB/s (ATA8-ACS 1699-D
Revision 3f)
218
219
(O)V
0000h
NV Cache Write Transfer Speed in MB/s
NV Cache Options
15–8
7–0
F
F
00h
00h
Reserved
Device Estimated Time to Spin Up in Seconds
Reserved
220
221
15–8
7–0
F
00h
V
00h
Write-Read-Verify feature set current mode
Reserved
0000h
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
22
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Device ID
Table 12: Identity Device (Continued)
See Note 1 for setting definitions
Word
Bit(s)
Setting
Default Value Description
222
Transport Major revision number. 0000h or FFFFh = device
does not report version
15–12
0001b
Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved
Parallel (Type = 0) Serial (Type = 1)
11–6
000000b
1b
Reserved Reserved
5
4
3
2
1
0
Reserved SATA Rev 3.0
Reserved SATA Rev 2.6
Reserved SATA Rev 2.5
Reserved SATA II: Extensions
Reserved SATA 1.0a
1b
1b
1b
1b
1b
ATA8-APT ATA8-AST
223
224
(M)F
( )F
0000h
Transport Minor revision number
Reserved for CE-ATA
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
234
235
236
(O)F
0001h
Minimum number of 512 byte units per DOWNLOAD MI-
CROCODE command for mode 3
00FFh
Maximum number of 512 byte units per DOWNLOAD MI-
CROCODE command for mode 3
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h
Reserved
255
(M)F
Integrity word
Checksum
15–8
7–0
varies
A5h
Signature
1. F = The content of the word is fixed and does not change.
V = The content of the word is variable and may change depending on the state of the
device or the commands executed by the device.
Note:
X = The content of the word may be fixed or variable.
R = The content of the word is reserved and will be zero.
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
23
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Commands
Commands
Table 13: Supported ATA Command Set
See ATA-8 standard for command details
Command Name
Command Code (hex)
CHECK POWER MODE
DEVICE CONFIGURATION RESTORE
DEVICE CONFIGURATION FREEZE LOCK
DEVICE CONFIGURATION IDENTIFY
DEVICE CONFIGURATION SET
DOWNLOAD MICROCODE
EXECUTE DEVICE DIAGNOSTIC
FLUSH CACHE
98h or E5h
B1h/C1h
B1h/C3h
B1h/C1h
B1h/C3h
92h
90h
E7h
FLUSH CACHE EXT
EAh
IDENTIFY DEVICE
ECh
IDLE
E3h or 97h
E1h or 95h
91h
IDLE IMMEDIATE
INITIALIZE DEVICE PARAMETERS
NOP
00h
READ BUFFER
E4h
READ DMA (with retry)
READ DMA (without retry)
READ DMA EXT
C8h
C9h
25h
READ FPDMA QUEUED
READ LOG EXT
60h
2Fh
READ MULTIPLE
C4h
READ MULTIPLE EXT
29h
READ NATIVE MAX ADDRESS
READ NATIVE MAX ADDRESS EXT
READ SECTOR(S) EXT
F8h
27h
24h
READ SECTOR(S) (with retry)
READ SECTOR(S) (without retry)
READ VERIFY SECTOR EXT
READ VERIFY SECTOR(S) (with retry)
SCT WRITE SAME
20h
21h
42h
40h
02h/0001h
02h/0002h
02h/0101h
02h/0102h
SCT RETURN ERROR RECOVERY CONTROL
SCT SET ERROR RECOVERY CONTROL
SCT SET FEATURE CONTROL
030h/01h
03h/01h
04h/01h
04h/02h
SCT RETURN FEATURE CONTROL
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
24
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Commands
Table 13: Supported ATA Command Set (Continued)
See ATA-8 standard for command details
Command Name
Command Code (hex)
04h/03h
05h/01h
F6h
SCT RETURN FEATURE OPTION FLAG
SCT RETURN SCT DATA TABLE
SECURITY DISABLE PASSWORD
SECURITY ERASE PREPARE
SECURITY ERASE UNIT
SECURITY FREEZE LOCK
SECURITY SET PASSWORD
SECURITY UNLOCK
F3h
F4h
F5h
F1h
F2h
SEEK
7xh
SET FEATURES
EFh
SET MAX ADDRESS
F9h
SET MAX – FREEZE LOCK
SET MAX – LOCK
F9h/04h
F9h/02h
37h
SET MAX ADDRESS EXT
SET MULTIPLE MODE
SET MAX – SET PASSWORD
SET MAX – UNLOCK
C6h
F9h/01h
F9h/03h
E6h or 99h
B0h/D9h
B0h/D8h
B0h/D2h
B0h/D4h
B0h/D0h
B0h/D5h
B0h/DAh
B0h/D6h
E2h or 96h
E0h or 94h
E8h
SLEEP
SMART DISABLE OPERATIONS
SMART ENABLE OPERATIONS
SMART ENABLE/DISABLE AUTOSAVE
SMART EXECUTE OFF-LINE IMMEDIATE
SMART READ DATA
SMART READ LOG SECTOR
SMART RETURN STATUS
SMART WRITE LOG
STANDBY
STANDBY IMMEDIATE
WRITE BUFFER
WRITE DMA (with retry)
WRITE DMA (without retry)
WRITE DMA EXT
CAh
CBh
35h
WRITE DMA FUA EXT
WRITE FPDMA QUEUED
WRITE LOG EXT
3Dh
61h
3Fh
WRITE MULTIPLE
C5h
WRITE MULTIPLE EXT
39h
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
25
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Commands
Table 13: Supported ATA Command Set (Continued)
See ATA-8 standard for command details
Command Name
Command Code (hex)
WRITE MULTIPLE FUA EXT
WRITE SECTOR(S) (with retry)
WRITE SECTOR(S) EXT
CEh
30h
34h
45h
WRITE UNCORRECTABLE EXT
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
26
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Compliance
Compliance
Micron SSDs comply with the following:
• RoHS “green”
• CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003
• FCC: CFR Title 47, Part 15, ICES-003, all Class B
• UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Ed-
ition
• BSMI (Taiwan): approval to CNS 13438
• C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22
• KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B
• W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations
may apply to customers who place these products in the markets where WEEE is en-
forced.
• TUV (Germany): approval to IEC60950/EN60950
• VCCI
• IC (Canada):
- This Class B digital apparatus complies with Canadian ICES-003.
- Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Rules
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
27
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Package Dimensions
Package Dimensions
Figure 4: mSATA Package – 50.80mm
2.60mm
0.102in
(2 PLCS)
DIA THRU
3.11mm
0.122in
P1
0.75mm
0.030in
1.00mm
RAD
RAD
0.039in
5.69mm
0.224in
(2 PLCS)
3.75mm
0.148in
1.40mm
0.055in
1.00mm
0.039in
1.35mm
0.053in
4.34mm
0.171in
3.53mm
0.139in
(2 PLCS)
2.08mm
0.082in
2.83mm
0.111in
11.08mm
0.436in
29.85mm
1.175in
2.08mm
0.082in
2.83mm
0.111in
2.75mm
0.108in
5.27mm
0.207in
50.80mm
2.000in
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
28
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
References
References
• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available
at www.sata-io.org
• SATA 3.0 GOLD
• ATA-8 ACS2
• JEDEC MO-300B (mSATA SSD Assembly)
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
29
© 2011 Micron Technology, Inc. All rights reserved.
C400v mSATA NAND Flash SSD
Revision History
Revision History
Rev. E – 8/12
• Changed MTBF to MTTF.
• Added new power-off sequence note to Maximum Ratings table.
• Added new note to Word 76 in Device ID table.
Rev. D – 4/12
• In Features section, removed reference to hot-plug-capable and changed caseless de-
sign height from 3.80mm to 3.75mm.
• In Physical Configuration section, changed height from 3.80mm to 3.75mm.
• Updated package dimensions figure (mSATA Package – 50.80mm):
– 3.80mm to 3.75mm
– 0.150in to 0.148in
– 1.40mm to 1.35mm
– 0.055in to 0.053in
Rev. C – 3/12
Rev. B – 1/12
Rev. A – 10/11
• Added Cache Drive Performance table to Performance.
• Added 32GB.
• Initial release.
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization some-
times occur.
PDF: 09005aef8485be28
realssd_c400v_msata.pdf - Rev. E 8/12 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
30
© 2011 Micron Technology, Inc. All rights reserved.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明