MT9123APR 概述
Telecom IC, CMOS, PQCC28 其他电信集成电路
MT9123APR 规格参数
是否无铅: | 含铅 | 是否Rohs认证: | 不符合 |
生命周期: | Obsolete | 零件包装代码: | LCC |
针数: | 28 | Reach Compliance Code: | unknown |
风险等级: | 5.72 | Is Samacsys: | N |
JESD-30 代码: | S-PQCC-J28 | 端子数量: | 28 |
最高工作温度: | 85 °C | 最低工作温度: | -40 °C |
封装主体材料: | PLASTIC/EPOXY | 封装代码: | QCCJ |
封装等效代码: | LDCC28,.5SQ | 封装形状: | SQUARE |
封装形式: | CHIP CARRIER | 电源: | 5 V |
认证状态: | Not Qualified | 子类别: | Other Telecom ICs |
标称供电电压: | 5 V | 表面贴装: | YES |
技术: | CMOS | 温度等级: | INDUSTRIAL |
端子形式: | J BEND | 端子节距: | 1.27 mm |
端子位置: | QUAD | Base Number Matches: | 1 |
MT9123APR 数据手册
通过下载MT9123APR数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载CMOS
MT9123
Dual Voice Echo Canceller
Data Sheet
November 2005
Features
•
Dual channel 64 ms or single channel 128 ms
Ordering Information
echo cancellation
MT9123AP
28 Pin PLCC
28 Pin PDIP
Tubes
•
•
•
•
Conforms to ITU-T G.165 requirements
Narrow-band signal detection
Programmable double-talk detection threshold
MT9123AE
Tubes
MT9123APR
MT9123AP1
MT9123APR1
28 Pin PLCC
Tape & Reel
Tubes
28 Pin PLCC*
28 Pin PLCC*
*Pb Free Matte Tin
Tape & Reel
Non-linear processor with adaptive suppression
threshold and comfort noise insertion
-40°C to +85°C
•
•
Offset nulling of all PCM channels
Description
Controllerless mode or Controller mode with
serial interface
The MT9123 Voice Echo Canceller implements a cost
effective solution for telephony voice-band echo
cancellation conforming to ITU-T G.165 requirements.
The MT9123 architecture contains two echo cancellers
which can be configured to provide dual channel 64
millisecond echo cancellation or single channel 128
millisecond echo cancellation.
•
•
ST-BUS or variable-rate SSI PCM interfaces
Selectable µ/A-Law ITU-T G.711; µ/A-Law Sign
Mag; linear 2’s complement
•
•
•
Per channel selectable 12 dB attenuator
Transparent data transfer and mute option
19.2 MHz master clock operation
The MT9123 operates in two major modes: Controller
or Controllerless. Controller mode allows access to an
Applications
array of features for customizing
the MT9123
•
•
Wireless Telephony
Trunk echo cancellers
operation. Controllerless mode is for applications
where default register settings are sufficient.
Linear/
Non-Linear
Processor
Offset
Null
Linear/
Sin
+
Sout
µ/A-Law
µ/A-Law
-
Microprocessor
Interface
Double-Talk
Detector
Programmable
Bypass
Narrow-Band
Detector
Offset
Null
12dB
Linear/
Linear/
Rin
ENA1
ENB1
Rout
ENA2
ENB2
Attenuator
µ/A-Law
µ/A-Law
CONFIG1
CONFIG2
S1/DATA1
S2/DATA2
S3/CS
Echo Canceller A
Echo Canceller B
NLP
LAW
FORMAT
IC3
IC4
S4/SCLK
IC1
IC2
VDD
VSS
PWRDN
F0od
F0i
BCLK/C4i
MCLK
Figure 1 - Functional Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 1996-2005, Zarlink Semiconductor Inc. All Rights Reserved.
MT9123
Data Sheet
1
2
ENA1
ENB1
ENA2
CONFIG2
CONFIG1
BCLK/C4i
28
27
26
25
24
23
3
4
5
ENB2
Rin
•
F0i
Rin
F0i
5
6
7
8
9
25
24
Rout
Sin
Rout
PDIP
Sin
6
7
Sout
VDD
F0od
23 Sout
22 VDD
VSS
MCLK
IC1
VSS
22
21
20
19
18
17
PLCC
8
21
MCLK
IC1
F0od
NLP 10
20 S1/DATA1
9
S1/DATA1
S2/DATA2
S3/CS
11
19
IC2
S2/DATA2
10
11
12
13
14
NLP
IC2
LAW
S4/SCLK
IC4
FORMAT
16
15
IC3
PWRDN
Figure 2 - Pin Connections
Description
Pin Description
Pin #
Name
1
ENA1
SSI Enable Strobe / ST-BUS Mode for Rin/Sout (Input). This pin has dual functions
depending on whether SSI or ST-BUS is selected.
For SSI, this strobe must be present for frame synchronization. This is an active high channel
enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer for Echo Canceller A
on Rin/Sout pins. Strobe period is 125 microseconds.
For ST-BUS, this pin, in conjunction with the ENB1 pin, will select the proper ST-BUS mode
for Rin/Sout pins (see ST-BUS Operation description). The selected mode applies to both
Echo Canceller A and B.
2
3
ENB1
ENA2
SSI Enable Strobe / ST-BUS Mode for Rin/Sout (Input). This pin has dual functions
depending on whether SSI or ST-BUS is selected.
For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial
PCM data transfer for Echo Canceller B on Rin/Sout pins. Strobe period is 125 microseconds.
For ST-BUS, this pin, in conjunction with the ENA1 pin, will select the proper ST-BUS mode
for Rin/Sout pins (see ST-BUS Operation description). The selected mode applies to both
Echo Canceller A and B.
SSI Enable Strobe / ST-BUS Mode for Sin/Rout (Input). This pin has dual functions
depending on whether SSI or ST-BUS is selected.
For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial
PCM data transfer for Echo Canceller A on Sin/Rout pins. Strobe period is 125 microseconds.
For ST-BUS, this pin, in conjunction with the ENB2 pin, will select the proper ST-BUS mode
for Sin/Rout pins (see ST-BUS Operation description). The selected mode applies to both
Echo Canceller A and B.
2
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Pin Description (continued)
Pin #
Name
Description
4
ENB2
SSI Enable Strobe / ST-BUS Mode for Sin/Rout (Input). This pin has dual functions
depending on whether SSI or ST-BUS is selected.
For SSI, this is an active high channel enable strobe, 8 or 16 data bits wide, enabling serial
PCM data transfer for Echo Canceller B on Sin/Rout pins. Strobe period is 125 microseconds.
For ST-BUS, this pin, in conjunction with the ENA2 pin, will select the proper ST-BUS mode
for Sin/Rout pins (see ST-BUS Operation description). The selected mode applies to both
Echo Canceller A and B.
5
6
Rin
Sin
Receive PCM Signal Input (Input). 128 kbit/s to 4096 kbit/s serial PCM input stream. Data
may be in either companded or 2’s complement linear format. Two PCM channels are time-
multiplexed on this pin. These are the Receive Input reference channels for Echo Cancellers
A and B. Data bits are clocked in following SSI or ST-BUS timing requirements.
Send PCM Signal Input (Input). 128 kbit/s to 4096 kbit/s serial PCM input stream. Data may
be in either companded or 2’s complement linear format. Two PCM channels are time-
multiplexed on this pin. These are the Send Input channels (after echo path) for Echo
Cancellers A and B. Data bits are clocked in following SSI or ST-BUS timing requirements.
7
8
VSS
Digital Ground. Nominally 0 volts.
MCLK Master Clock (Input). Nominal 20 MHz Master Clock input. May be connected to an
asynchronous (relative to frame signal) clock source.
9
IC1
Internal Connection 1 (Input). Must be tied to Vss.
10
NLP
Non-Linear Processor Control (Input).
Controllerless Mode: An active high enables the Non-Linear Processors in Echo Cancellers A
and B. Both NLP’s are disabled when low. Intended for conformance testing to G.165 and it is
usually tied to Vdd for normal operation.
Controller Mode: This pin is ignored (tie to Vdd or Vss). The non-linear processor operation is
controlled by the NLPDis bit in Control Register 2. Refer to the Register Summary.
11
12
IC2
Internal Connection 2 (Input). Must be tied to Vss.
LAW
A/µ Law Select (Input). An active low selects µ−Law companded PCM. When high, selects
A-Law companded PCM. This control is for both echo cancellers and is valid for both
controller and controllerless modes.
13
14
FORMAT ITU-T/Sign Mag (Input). An active low selects sign-magnitude PCM code. When high,
selects ITU-T (G.711) PCM code. This control is for both echo cancellers and is valid for both
controller and controllerless modes.
PWRDN Power-down (Input). An active low resets the device and puts the MT9123 into a low-power
stand-by mode.
15
16
IC3
IC4
Internal Connection 3 (Output). Must be left unconnected.
Internal Connection 4 (Output). Must be left unconnected.
3
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Pin Description (continued)
Pin #
Name
Description
17/18
S4/S3 Selection of Echo Canceller B Functional States (Input).
Controllerless Mode: Selects Echo Canceller B functional states according to Table 2.
Controller Mode: S4 and S3 pins become SCLK and CS pins respectively.
Serial Port Synchronous Clock (Input). Data clock for the serial microport interface.
Chip Select (Input). Enables serial microport interface data transfers. Active low.
17
SCLK
CS
18
19/20
S2/S1 Selection of Echo Canceller A Functional States (Input).
Controllerless Mode: Selects Echo Canceller A functional states according to Table 2.
Controller Mode: S2 and S1 pins become DATA2 and DATA1 pins respectively.
Serial Data Receive (Input).
19
DATA2
In Motorola/National serial microport operation, the DATA2 pin is used for receiving data. In
Intel serial microport operation, the DATA2 pin is not used and must be tied to Vss or Vdd.
Serial Data Port (Bidirectional).
In Motorola/National serial microport operation, the DATA1 pin is used for transmitting data. In
Intel serial microport operation, the DATA1 pin is used for transmitting and receiving data.
20
21
DATA1
F0od
Delayed Frame Pulse Output (Output). In ST-BUS operation, this pin generates a delayed
frame pulse after the 4th channel time slot and is used for daisy-chaining multiple ST-BUS
devices. See Figures 4 to 7.
In SSI operation, this pin outputs logic low.
22
23
VDD
Sout
Positive Power Supply. Nominally 5 volts.
Send PCM Signal Output (Output). 128 kbit/s to 4096 kbit/s serial PCM output stream. Data
may be in either companded or 2’s complement linear PCM format. Two PCM channels are
time-multiplexed on this pin. These are the Send Out signals after echo cancellation and Non-
linear processing. Data bits are clocked out following SSI or ST-BUS timing requirements.
24
Rout
Receive PCM Signal Output (Output). 128 kbit/s to 4096 kbit/s serial PCM output stream.
Data may be in either companded or 2’s complement linear PCM format. Two PCM channels
are time-multiplexed on this pin. This output pin is provided for convenience in some
applications and may not always be required. Data bits are clocked out following SSI or ST-
BUS timing requirements.
25
26
F0i
Frame Pulse (input). In ST-BUS operation, this is a frame alignment low going pulse. SSI
operation is enabled by connecting this pin to Vss.
BCLK/C4i Bit Clock/ST-BUS Clock (Input). In SSI operation, BCLK pin is a 128 kHz to 4.096 MHz bit
clock. This clock must be synchronous with ENA1, ENA2, ENB1 and ENB2 enable strobes.
In ST-BUS operation, C4i pin must be connected to the 4.096 MHz (C4) system clock.
4
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Pin Description (continued)
Pin # Name
Description
27/28 CONFIG1/ Device Configuration Pins (Inputs). When CONFIG1 and CONFIG2 pins are both logic 0,
the MT9123 serial microport is enabled. This configuration is defined as Controller Mode.
When CONFIG1 and CONFIG2 pins are in any other logic combination, the MT9123 is
configured in Controllerless Mode. See Table 3.
CONFIG2
Notes:
1. All unused inputs should be connected to logic low or high unless otherwise stated. All outputs should be left open circuit when not used.
2. All inputs have TTL compatible logic levels except for MCLK, Sin and Rin pins which have CMOS compatible logic levels and PWRDN pin
which has Schmitt trigger compatible logic levels.
3. All outputs are CMOS pins with CMOS logic levels.
Functional Description
The MT9123 architecture contains two individually controlled echo cancellers (Echo Canceller A and B). They can
be set in three distinct configurations: Normal, Back-to-Back and Extended Delay (see Figure 3). Under Normal
configuration, the two echo cancellers are positioned in parallel providing 64 millisecond echo cancellation in two
channels simultaneously. In Back-to-Back configuration, the two echo cancellers are positioned to cancel echo
coming from both directions in a single channel. In Extended-Delay configuration, the two echo cancellers are
internally cascaded into one 128 millisecond echo canceller.
Each echo canceller contains the following main elements (see Figure 1).
•
•
•
•
•
•
•
•
•
Adaptive Filter for estimating the echo channel
Subtracter for cancelling the echo
Double-Talk detector for disabling the filter adaptation during periods of double-talk
Non-Linear Processor for suppression of residual echo
Narrow-Band Detector for preventing Adaptive Filter divergence caused by narrow-band signals
Offset Null filters for removing the DC component in PCM channels
12 dB attenuator for signal attenuation
Serial controller interface compatible with Motorola, National and Intel microcontrollers
PCM encoder/decoder compatible with µ/A-Law ITU-T G.711, µ/A-Law Sign-Mag or linear 2’s complement
coding
The MT9123 has two modes of operation: Controllerless and Controller. Controllerless mode is intended for
applications where customization is not required. Controller mode allows access to all registers for customizing the
MT9123 operation. Refer to Table 7 for a complete list. Controller mode is selected when CONFIG1 and CONFIG2
pins are both connected to Vss.
Each echo canceller in the MT9123 has four functional states: Mute, Bypass, Disable Adaptation and Enable
Adaptation. These are explained in the section entitled Echo Canceller Functional States.
5
Zarlink Semiconductor Inc.
MT9123
Data Sheet
PORT 1
PORT 2
channel A
PORT 2
PORT 1
Sin
+
Sout
channel A
channel A
-
Sout
Sin
+
echo
Adaptive Filter
(128 ms)
path A
-
echo
path A
Adaptive
channel A
Filter (64 ms)
Rout
Rin
Optional -12dB pad
Rout
Rin
E.C.A
Optional -12dB pad
b) Extended Delay Configuration (128 ms)
E.C.A
PORT 2
PORT 1
channel B
+
Sout
+
Sin
-
-
Optional -12dB pad
echo
Adaptive
echo
path
echo
path
Adaptive
path B
Filter (64 ms)
Adaptive
Filter (64 ms)
Filter (64ms)
channel B
-
+
Rout
Rin
Optional -12dB pad
E.C.B
Optional -12dB pad
E.C.A
E.C.B
a) Normal Configuration (64 ms)
c) Back-to-Back Configuration (64 ms)
Figure 3 - Device Configuration
Adaptive Filter
The adaptive filter is a 1024 tap FIR filter which is divided into two sections. Each section contains 512 taps
providing 64 ms of echo estimation. In Normal configuration, the first section is dedicated to channel A and the
second section to channel B. In Extended Delay configuration, both sections are cascaded to provide 128 ms of
echo estimation in channel A.
Double-Talk Detector
Double-Talk is defined as those periods of time when signal energy is present in both directions simultaneously.
When this happens, it is necessary to disable the filter adaptation to prevent divergence of the adaptive filter
coefficients. Note that when double-talk is detected, the adaptation process is halted but the echo canceller
continues to cancel echo.
A double-talk condition exists whenever the Sin signal level is greater than the expected return echo level. The
relative signal levels of Rin (Lrin) and Sin (Lsin) are compared according to the following expression to identify a
double-talk condition:
Lsin > Lrin + 20log10(DTDT)
where DTDT is the Double-Talk Detection Threshold. Lsin and Lrin are the relative signal levels expressed in
dBm0.
A different method is used when it is uncertain whether Sin consists of a low level double-talk signal or an echo
return. During these periods, the adaptation process is slowed down but it is not halted.
6
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Controllerless Mode
In G.165 standard, the echo return loss is expected to be at least 6 dB. This implies that the Double-Talk Detector
Threshold (DTDT) should be set to 0.5 (-6 dB). However, in order to get additional guardband, the DTDT is set
internally to 0.5625 (-5 dB). In controllerless mode, the Double-Talk Detector is always active.
Controller Mode
In some applications the return loss can be higher or lower than 6 dB. The MT9123 allows the user to change the
detection threshold to suit each application’s need. This threshold can be set by writing the desired threshold value
into the DTDT register.
The DTDT register is 16 bits wide. The register value in hexadecimal can be calculated with the following equation:
DTDT(hex) = hex(DTDT(dec) * 32768)
where 0 < DTDT(dec) < 1
Example: For DTDT = 0.5625 (-5 dB), the
hexadecimal value becomes
hex(0.5625 * 32768) = 4800h
Non-Linear Processor (NLP)
After echo cancellation, there is always a small amount of residual echo which may still be audible. The MT9123
uses an NLP to remove residual echo signals which have a level lower than the Adaptive Suppression Threshold
(TSUP in G.165). This threshold depends upon the level of the Rin (Lrin) reference signal as well as the
programmed value of the Non-Linear Processor Threshold register (NLPTHR). TSUP can be calculated by the
following equation:
TSUP = Lrin + 20log10(NLPTHR)
where NLPTHR is the Non-Linear Processor Threshold register value and Lrin is the relative power level expressed
in dBm0.
When the level of residual error signal falls below TSUP, the NLP is activated further attenuating the residual signal
to less than -65 dBm0. To prevent a perceived decrease in background noise due to the activation of the NLP, a
spectrally-shaped comfort noise, equivalent in power level to the background noise, is injected. This keeps the
perceived noise level constant. Consequently, the user does not hear the activation and de-activation of the NLP.
Controllerless Mode
The NLP processor can be disabled by connecting the NLP pin to Vss.
Controller Mode
The NLP processor can be disabled by setting the NLPDis bit to 1 in Control Register 2.
The NLPTHR register is 16 bits wide. The register value in hexadecimal can be calculated with the following
equation:
NLPTHR(hex) = hex(NLPTHR(dec) * 32768)
where 0 < NLPTHR(dec) < 1
The comfort noise injection can be disabled by setting the INJDis bit to 1 in Control Register 1.
7
Zarlink Semiconductor Inc.
MT9123
Data Sheet
It should be noted that the NLPTHR is valid and the comfort noise injection is active only when the NLP is enabled.
Narrow Band Signal Detector (NBSD)
Single or dual frequency tones (e.g., DTMF tones) present in the reference input (Rin) of the echo canceller for a
prolonged period of time may cause the adaptive filter to diverge. The Narrow Band Signal Detector (NBSD) is
designed to prevent this divergence by detecting single or dual tones of arbitrary frequency, phase, and amplitude.
When narrow band signals are detected, the adaptation process is halted but the echo canceller continues to
cancel echo.
Controllerless Mode
The NBSD is always active and automatically disables the filter adaptation process when narrow band signals are
detected.
Controller Mode
The NBSD can be disabled by setting the NBDis bit to 1 in Control Register 2.
Offset Null Filter
Adaptive filters in general do not operate properly when a DC offset is present on either the reference signal (Rin)
or the echo composite signal (Sin). To remove the DC component, the MT9123 incorporates Offset Null filters in
both Rin and Sin inputs.
Controllerless Mode
The Offset Null filters are always active.
Controller Mode
The offset null filters can be disabled by setting the HPFDis bit to 1 in Control Register 2.
Echo Canceller Functional States
Each echo canceller has four functional states: Mute, Bypass, Disable Adaptation and Enable Adaptation.
Mute:
The Mute state forces the echo canceller to transmit quiet code and halts the filter adaptation process.
In Normal configuration, the PCM output data on Rout is replaced with the quiet code according to the following
table.
LINEAR
16 bits
SIGN/
MAGNITUDE
µ-Law
CCITT (G.711)
2’s
µ-Law
FFh
A-Law
complement
A-Law
+Zero
(quiet
code)
0000h
80h
D5h
Table 1 - Quiet PCM Code Assignment
In Back-to-Back configuration, both echo cancellers are combined to implement a full duplex echo canceller.
Therefore muting Echo Canceller A causes quiet code to be transmitted on Rout, while muting Echo Canceller B
causes quiet code to be transmitted on Sout.
8
Zarlink Semiconductor Inc.
MT9123
Data Sheet
In Extended Delay configuration, both echo cancellers are cascaded to make one 128 ms echo canceller. In this
configuration, muting Echo Canceller A causes quiet code to be transmitted on Rout.
Bypass:
The Bypass state directly transfers PCM codes from Rin to Rout and from Sin to Sout. When Bypass state is
selected, the adaptive filter coefficients are reset to zero.
Disable Adaptation:
When the Disable Adaptation state is selected, the adaptive filter coefficients are frozen at their current value. In
this state, the adaptation process is halted however the MT9123 continues to cancel echo.
Enable Adaptation:
In Enable Adaptation state, the adaptive filter coefficients are continually updated. This allows the echo canceller to
model the echo return path characteristics in order to cancel echo. This is the normal operating state.
Controllerless Mode
The four functional states can be selected via S1, S2, S3, and S4 pins as shown in the following table.
Echo
Echo
Canceller A
Canceller B
Functional State
S2/S1
S4/S3
00
01
10
11
Mute(1)
00
01
10
11
Bypass(2)
Disable Adaptation(1,3)
Enable Adaptation(3)
Table 2 - Functional States Control Pins
(1) Filter coefficients are frozen (adaptation disabled)
(2) The adaptive filter coefficients are reset to zero
(3) The MT9123 cancels echo
Controller Mode
The echo canceller functions are selected in Control Register 1 and Control Register 2 through four control bits:
MuteS, MuteR, Bypass and AdaptDis. See Register Summary for details.
MT9123 Throughput Delay
The throughput delay of the MT9123 varies according to the data path and the device configuration. For all device
configurations, except for Bypass state, Rin to Rout has a delay of two frames and Sin to Sout has a delay of three
frames. In Bypass state, the Rin to Rout and Sin to Sout paths have a delay of two frames. In ST-BUS operation,
the D and C channels have a delay of one frame.
Power Down
Forcing the PWRDN pin to logic low, will put the MT9123 into a power down state. In this state all internal clocks are
halted, the DATA1, Sout and Rout pins are tristated and the F0od pin output high.
The device will automatically begin the execution of its initialization routines when the PWRDN pin is returned to
logic high and a clock is applied to the MCLK pin. The initialization routines execute for one frame and will set the
MT9123 to default register values.
9
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Device Configuration
The MT9123 architecture contains two individually controlled echo cancellers (Echo Canceller A and B). They can
be set in three distinct configurations: Normal, Back-to-Back, and Extended Delay. See Figure 3.
Normal Configuration:
In this configuration, the two echo cancellers (Echo Canceller A and B) are positioned in parallel, as shown in
Figure 3a, providing 64 milliseconds of echo cancellation in two channels simultaneously.
In SSI operation, both channels are available in different timeslots on the same TDM (Time Division Multiplexing)
bus. For Echo Canceller A, the ENA1 enable strobe pin defines the Rin/Sout (PORT1) time slot while the ENA2
enable strobe pin defines the Sin/Rout (PORT2) time slot. The ENB1 and ENB2 enable strobes perform the same
function for Echo Canceller B.
In ST-BUS operation, the ENA1, ENA2, ENB1 and ENB2 pins are used to determine the PCM data format and the
channel locations. See Table 4.
Back-to-Back Configuration:
In this configuration, the two echo cancellers are positioned to cancel echo coming from both directions in a single
channel providing full duplex 64 millisecond echo-cancellation. See Figure 3c. This configuration uses only one
timeslot on PORT1 and PORT2, allowing a no-glue interface for applications where bidirectional echo cancellation
is required.
In SSI operation, ENA1 and ENA2 enable pins are used to strobe data on Rin/Sout and Sin/Rout respectively. In
ST-BUS operation, ENA1, ENA2, ENB1 and ENB2 inputs are used to select the ST-BUS mode according to Table
4.
Examples of Back-to-Back configuration include positioning the MT9123 between a codec and a transmission
device or between two codecs for echo control on analog trunks.
Extended Delay configuration:
In this configuration, the two echo cancellers are internally cascaded into one 128 millisecond echo canceller. See
Figure 3b. In SSI operation, ENA1 and ENA2 enable pins are used to strobe data on Rin/Sout and Sin/Rout
respectively. In ST-BUS operation, ENA1, ENA2, ENB1 and ENB2 inputs are used to select the ST-BUS mode
according to Table 4.
Controllerless Mode
The three configurations can be selected through the CONFIG1 and CONFIG2 pins as shown in the following
table.
CONFIG1
CONFIG2
CONFIGURATION
0
0
1
1
0
1
0
1
(selects Controller Mode)
Extended Delay Mode
Back-to-Back Mode
Normal Mode
Table 3 - Configuration in Controllerless Mode
Controller Mode
In Control Register 1, the Normal configuration can be programmed by setting both BBM and Extended-Delay bits
to 0. Back-to-Back configuration can be programmed by setting the BBM bit to 1 and Extended-Delay bit to 0.
10
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Extended-Delay configuration can be programmed by setting the Extended-Delay bit to 1 and BBM bit to 0. Both
BBM and Extended-Delay bits in Control Register 1 can not be set to 1 at the same time.
PCM Data I/O
The PCM data transfer for the MT9123 is provided through two PCM ports. PORT1 consists of Rin and Sout pins
while PORT2 consists of Sin and Rout Pins. The Data is transferred through these ports according to either ST-
BUS or SSI conventions. The device determines the mode of operation by monitoring the signal applied to the F0i
pin. When a valid ST-BUS frame pulse is applied to the F0i pin, the MT9123 will assume ST-BUS operation. If F0i is
tied continuously to Vss the MT9123 will assume SSI operation.
ST-BUS Operation
The ST-BUS PCM interface conforms to Zarlink’s ST-BUS standard and it is used to transport 8 bit companded
PCM data (using one timeslot) or 16 bit 2’s complement linear PCM data (using two timeslots). Pins ENA1 and
ENB1 select timeslots on PORT1 while pins ENA2 and ENB2 select timeslots on PORT2. See Table 4 and Figures
5 to 8.
PORT1
ST-BUS Mode
Selection
PORT2
Rin/Sout
Sin/Rout
Enable Pins
Enable Pins
ENB1 ENA1
ENB2 ENA2
0
0
1
0
1
0
Mode 1. 8 bit companded PCM I/O on
timeslots 0 & 1.
0
0
1
0
1
0
Mode 2. 8 bit companded PCM I/O on
timeslots 2 & 3.
Mode 3. 8 bit companded PCM I/O on
timeslots 2 & 3. Includes D & C chan-
nel bypass in timeslots 0 & 1.
1
1
Mode 4. 16 bit 2’s complement linear
PCM I/O on timeslots 0 - 3.
1
1
Table 4 - ST-BUS Mode Select
Note that if the device is in back-to-back or extended delay configurations, the second timeslot in any ST-BUS
Mode contains undefined data. This means that the following timeslots contain undefined data: timeslot 1 in ST-
BUS Mode 1; timeslot 3 in ST-BUS Modes 2 & 3 and timeslots 2 and 3 in ST-BUS Mode 4.
SSI Operation
The SSI PCM interface consists of data input pins (Rin, Sin), data output pins (Sout, Rout), a variable rate bit clock
(BCLK), and four enable pins (ENA1,ENB1, ENA2 and ENB2) to provide strobes for data transfers. The active high
enable may be either 8 or 16 BCLK cycles in duration. Automatic detection of the data type (8 bit companded or 16
bit 2’s complement linear) is accomplished internally. The data type cannot change dynamically from one frame to
the next.
In SSI operation, the frame boundary is determined by the rising edge of the ENA1 enable strobe (see Figure 9).
The other enable strobes (ENB1, ENA2 and ENB2) are used for parsing input/output data and they must pulse
within 125 microseconds of the rising edge of ENA1. If they are unused, they must be tied to Vss.
In SSI operation, the enable strobes may be a mixed combination of 8 or 16 BCLK cycles allowing the flexibility to
mix 2’s complement linear data on one port (e.g., Rin/Sout) with companded data on the other port (e.g., Sin/Rout).
11
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Enable Strobe Pin
Echo Canceller
Port
ENA1
ENB1
ENA2
ENB2
A
B
A
B
1
1
2
2
Table 5 - SSI Enable Strobe Pins
PCM Law and Format Control (LAW, FORMAT)
The PCM companding/coding law used by the MT9123 is controlled through the LAW and FORMAT pins. ITU-T
G.711 companding curves for µ-Law and A-Law are selected by the LAW pin. PCM coding ITU-T G.711 and Sign-
Magnitude are selected by the FORMAT pin. See Table 6.
Sign-Magnitude
FORMAT=0
ITU-T (G.711)
FORMAT=1
PCM Code
µ/A-LAW
µ-LAW
A-LAW
LAW = 0 or 1
LAW = 0
LAW =1
+ Full Scale
+ Zero
1111 1111
1000 0000
0000 0000
0111 1111
1000 0000
1111 1111
0111 1111
0000 0000
1010 1010
1101 0101
0101 0101
0010 1010
- Zero
- Full Scale
Table 6 - Companded PCM
Linear PCM
The 16-bit 2’s complement PCM linear coding permits a dynamic range beyond that which is specified in ITU-T
G.711 for companded PCM. The echo-cancellation algorithm will accept 16 bits 2’s complement linear code which
gives a dynamic range of +15 dBm0.
Linear PCM data must be formatted as 14-bit, 2’s complement data with three bits of sign extension in the most
significant positions (i.e.: S,S,S,12,11, ...1,0) for a total of 16 bits where “S” is the extended sign bit. When A-Law is
converted to 2’s complement linear format, it must be scaled up by 6 dB (i.e., left shifted one bit) with a zero
inserted into the least significant bit position. See Figure 7.
Bit Clock (BCLK/C4i)
The BCLK/C4i pin is used to clock the PCM data in both SSI (BCLK) and ST-BUS (C4i) operations.
In SSI operation, the bit rate is determined by the BCLK frequency. This input must contain either eight or sixteen
clock cycles within the valid enable strobe window. BCLK may be any rate between 128 KHz to 4.096 MHz and can
be discontinuous outside of the enable strobe windows defined by ENA1, ENB1, ENA2 and ENB2 pins. Incoming
PCM data (Rin, Sin) are sampled on the falling edge of BCLK while outgoing PCM data (Sout, Rout) are clocked
out on the rising edge of BCLK. See Figure 17.
In ST-BUS operation, connect the system C4 (4.096 MHz) clock to the C4i pin.
12
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Master Clock (MCLK)
A nominal 20 MHz master clock (MCLK) is required for execution of the MT9123 algorithms. The MCLK input may
be asynchronous with the 8 KHz frame. If only one channel operation is required, (Echo Canceller A only) the
MCLK can be as low as 9.6 MHz.
Microport
The serial microport provides access to all MT9123 internal read and write registers and it is enabled when
CONFIG1 and CONFIG2 pins are both set to logic 0. This microport is compatible with Intel MCS-51 (mode 0),
Motorola SPI (CPOL=0, CPHA=0), and National Semiconductor Microwire specifications. The microport consists of
a transmit/receive data pin (DATA1), a receive data pin (DATA2), a chip select pin (CS) and a synchronous data
clock pin (SCLK).
The MT9123 automatically adjusts its internal timing and pin configuration to conform to Intel or Motorola/National
requirements. The microport dynamically senses the state of the SCLK pin each time CS pin becomes active (i.e.,
high to low transition). If SCLK pin is high during CS activation, then Intel mode 0 timing is assumed. In this case
DATA1 pin is defined as a bi-directional (transmit/receive) serial port and DATA2 is internally disconnected. If SCLK
is low during CS activation, then Motorola/National timing is assumed and DATA1 is defined as the data transmit pin
while DATA2 becomes the data receive pin. The MT9123 supports Motorola half-duplex processor mode (CPOL=0
and CPHA=0). This means that during a write to the MT9123, by the Motorola processor, output data from the
DATA1 pin must be ignored. This also means that input data on the DATA2 pin is ignored by the MT9123 during a
valid read by the Motorola processor.
All data transfers through the microport are two bytes long. This requires the transmission of a Command/Address
byte followed by the data byte to be written or read from the addressed register. CS must remain low for the
duration of this two-byte transfer. As shown in Figures 9 and 10, the falling edge of CS indicates to the MT9123 that
a microport transfer is about to begin. The first 8 clock cycles of SCLK after the falling edge of CS are always used
to receive the Command/Address byte from the microcontroller. The Command/Address byte contains information
detailing whether the second byte transfer will be a read or a write operation and at what address. The next 8 clock
cycles are used to transfer the data byte between the MT9123 and the microcontroller. At the end of the two-byte
transfer, CS is brought high again to terminate the session. The rising edge of CS will tri-state the DATA1 pin. The
DATA1 pin will remain tri-stated as long as CS is high.
Intel processors utilize Least Significant Bit (LSB) first transmission while Motorola/National processors use Most
Significant Bit (MSB) first transmission. The MT9123 microport automatically accommodates these two schemes
for normal data bytes. However, to ensure timely decoding of the R/W and address information, the
Command/Address byte is defined differently for Intel and Motorola/National operations. Refer to the relative timing
diagrams of Figures 9 and 10.
Receive data is sampled on the rising edge of SCLK while transmit data is clocked out on the falling edge of SCLK.
Detailed microport timing is shown in Figure 18 and Figure 19.
13
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Function
Controllerless
Controller
selected when pins CONFIG1 & 2 ≠ 00
selected when pins CONFIG1 & 2 = 00
Normal Configuration Set pins CONFIG1 to 1 and CONFIG2 1 to select this Set bits Extended-Delay to 0 and BBM to 0 in Control Reg-
configuration.
ister 1 to select.
Back-to-Back
Configuration
Set pins CONFIG1 to 1 and CONFIG2 to 0 to select
this configuration.
Set bit BBM to 1 in Control Register 1 to select.
Extended Delay
Configuration
Set pins CONFIG1 to 0 and CONFIG2 to 1 to select
this configuration.
Set bit Extended-Delay to 1 in Control Register 1 to select.
Mute
Set pins S2/S1 to 00 and S4/S3 to 00 to select for Echo Set bit MuteR to 1 or MuteS to 1 in Control Register 2 to
Canceller A and Echo Canceller B respectively. select.
Bypass
Set pins S2/S1 to 01 and S4/S3 to 01 to select for Echo Set bit Bypass to 1 in Control Register 1 to select.
Canceller A and Echo Canceller B, respectively.
Disable Adaptation
Enable Adaptation
Set pins S2/S1 to 10 and S4/S3 to 10 to select for Echo Set bit AdaptDis to 1 in Control Register 1 to select.
Canceller A and Echo Canceller B, respectively.
Set pins S2/S1 to 11 and S4/S3 to 11 to select for Echo Set bits AdaptDis to 0 and Bypass to 0 in Control Register
Canceller A and Echo Canceller B, respectively.
1 to select.
SSI
Tie pin F0i to VSS to select.
Tie pin F0i to VSS to select.
ST-BUS
Apply a valid ST-BUS frame pulse to F0i pin to select. Apply a valid ST-BUS frame pulse to F0i pin to select.
12dB Attenuator
Always disabled.
Set bit PAD to 1 in Control Register 1 to enable.
Double-Talk
Detector
Continuously enabled which disables filter adaptation
when double-talk is detected.
The detection threshold can be controlled via Double-Talk
Detection Threshold Register 1 and 2.
Non-Linear
Processor
Set pin NLP to 1 to enable.
Set bit NLPDis to 1 to disable.
PCM Law
Set pin LAW to 1 or 0 to select A-Law or µ-Law
respectively.
Set pin LAW to 1or 0 to select A-Law or µ-Law
respectively.
PCM Format
Set pin FORMAT to 0 or 1 to select Sign-Magnitude or Set pin FORMAT to 0 or 1 to select Sign-Magnitude or
ITU-T format respectively. ITU-T format respectively.
Narrow-Band Signal
Detector
Continuously enabled which disables the filter adapta- Set bit NBDis to 1 in Control Register 2 to disable.
tion when narrow band signal is detected.
Offset Null Filter
Continuously enabled which removes the DC compo-
nent in the PCM input.
Set bit HPFDis to 1 in Control Register 2 to disable.
Table 7 - MT9123 Function Control Summary
14
Zarlink Semiconductor Inc.
MT9123
Data Sheet
C4i
F0i
0
1
2
3
4
F0od
ECA
ECB
PORT1
Rin
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Sout
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
ECA
ECB
PORT2
Sin
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Rout
7 6 5 4 3 2 1 0
outputs=High impedance
inputs = don’t care
In ST-BUS Mode 1, both echo canceller I/O channels are assigned to ST-BUS timeslots 0 and 1. Note that the user could configure
PORT1 and PORT2 into different ST-BUS modes. The pin F0od is always delayed 4 time slots to permit a more flexible interleave of
ST-BUS modes.
Figure 4 - ST-BUS 8 Bit Companded PCM I/O on Timeslots 0 & 1 (Mode 1)
C4i
F0i
0
1
2
3
4
F0od
PORT1
Rin
ECA
ECB
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Sout
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
PORT2
Sin
ECA
ECB
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Rout
7 6 5 4 3 2 1 0
outputs=High impedance
inputs = don’t care
In ST-BUS Mode 2, both echo canceller I/O channels are assigned to ST-BUS timeslots 2 and 3. Note that the user could configure
PORT1 and PORT2 into different ST-BUS modes. The pin F0od is always delayed 4 time slots to permit a more flexible interleave of
ST-BUS modes.
Figure 5 - ST-BUS 8 Bit Companded PCM I/O on Timeslots 2 & 3 (Mode 2)
15
Zarlink Semiconductor Inc.
MT9123
Data Sheet
C4i
F0i
0
1
2
3
4
F0od
PORT1
Rin
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
ECA ECB
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Sout
PORT2
Sin
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
ECA
ECB
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Rout
outputs=High impedance
inputs = don’t care
indicates that an input channel is bypassed to an output channel
ST-BUS Mode 3 supports connection to 2B+D devices where timeslots 0 and 1 transport D and C channels and both echo canceller I/O
channels are assigned to ST-BUS timeslots 2 and 3. Both PORT1 and PORT2 must be configured in ST-BUS Mode 3.
Figure 6 - ST-BUS 8 Bit Companded PCM I/O with D and C channels (Mode 3)
C4i
F0i
F0od
Rin
S S S 12 1110 9 8 7 6 5 4 3 2 1 0 S S S 12 1110 9 8 7 6 5 4 3 2 1 0
ECA
PORT1
ECB
S S S 12 1110 9 8 7 6 5 4 3 2 1 0 S S S 12 1110 9 8 7 6 5 4 3 2 1 0
Sout
Sin
S S S 12 1110 9 8 7 6 5 4 3 2 1 0 S S S 12 1110 9 8 7 6 5 4 3 2 1 0
PORT2
ECB
ECA
Rout
S S S 12 1110 9 8 7 6 5 4 3 2 1 0 S S S 12 1110 9 8 7 6 5 4 3 2 1 0
outputs=High impedance
inputs = don’t care
ST-BUS Mode 4 allows 16 bits 2’s complement linear data to be transferred using ST-BUS I/O timing. Note that PORT1 and PORT2
need not necessarily both be in mode 4.
Figure 7 - ST-BUS 16 Bit 2’s Complement Linear PCM I/O (Mode 4)
16
Zarlink Semiconductor Inc.
MT9123
Data Sheet
BCLK
PORT1
ENA1
ECA
ECB
ENB1
Rin
8 or 16 bits
8 or 16 bits
ECA
8 or 16 bits
8 or 16 bits
ECB
Sout
PORT2
ENA2
ENB2
8 or 16 bits
8 or 16 bits
8 or 16 bits
8 or 16 bits
Sin
Rout
outputs=High impedance
inputs = don’t care
Note that the two ports are independent so that, for example, PORT1 can operate with 8 bit enable strobes and PORT2 can operate
with 16 bit enable strobes.
Figure 8 - SSI Operation
17
Zarlink Semiconductor Inc.
MT9123
Data Sheet
✑
COMMAND/ADDRESS
DATA INPUT/OUTPUT
✑
A0 A1 A2 A3 A4 A5
X
D0 D1 D2 D3 D4 D5 D6 D7
R/W
DATA 1
✑
SCLK
CS
✑
✑
✑
✑
Delays due to internal processor timing which are transparent to the MT9123.
The MT9123: latches receive data on the rising edge of SCLK
outputs transmit data on the falling edge of SCLK
✑
The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent
byte is always data followed by CS returning high.
A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again.
✑
✑
The COMMAND/ADDRESS byte contains: 1 bit - Read/Write
6 bits - Addressing Data
1 bit - Unused
Figure 9 - Serial Microport Timing for Intel Mode 0
COMMAND/ADDRESS ✑
DATA INPUT
✑
DATA 2
Receive
R/W A5 A4 A3 A2 A1 A0
X
D7 D6 D5 D4 D3 D2 D1 D0
DATA OUTPUT
DATA 1
D7 D6 D5 D4 D3 D2 D1 D0
High Impedance
Transmit
✑
SCLK
CS
✑
✑
✑
✑
Delays due to internal processor timing which are transparent to the MT9123.
The MT9123: latches receive data on the rising edge of SCLK
outputs transmit data on the falling edge of SCLK
✑
The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent
byte is always data followed by CS returning high.
A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again.
✑
✑
The COMMAND/ADDRESS byte contains: 1 bit - Read/Write
6 bits - Addressing Data
1 bit - Unused
Figure 10 - Serial Microport Timing for Motorola Mode 00 or National Microwire
18
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Register Summary
Echo Canceller A, Control Register 1
ADDRESS = 00h WRITE/READ VERIFY
Extended
Delay
Power Reset Value
0000 0000
CRA1
Reset
Bypass
AdaptDis
INJDis
BBM
PAD
0
7
6
5
4
3
2
1
0
Echo Canceller B, Control Register 1
ADDRESS = 20h WRITE/READ VERIFY
Power Reset Value
CRB1
Reset
Bypass
INJDis
BBM
PAD
AdaptDis
1
0
0000 0010
7
6
5
4
3
2
1
0
Extended- When high, Echo Cancellers A and B are internally cascaded into one 128ms echo canceller.
When low, Echo Cancellers A and B operate independently.
Delay
Do not enable both Extended-Delay and BBM configurations at the same time.
AdaptDis
Bypass
PAD
When high, echo canceller adaptation is disabled.
When low, the echo canceller dynamically adapts to the echo path characteristics.
When high, Sin data is by-passed to Sout and Rin data is by-passed to Rout.
When low, output data on both Sout and Rout is a function of the echo canceller algorithm.
When high, 12 dB of attenuation is inserted into the Rin to Rout path.
When low the Rin to Rout path gain is 0 dB.
BBM
When high the Back to Back configuration is enabled.
When low the Normal configuration is enabled. Do not enable Extended-Delay and BBM configurations at the same time.
Always set both BBM bits of the two echo cancellers to the same logic value to avoid conflict.
INJDis
Reset
When high, the noise injection process is disabled. When low noise injection is enabled.
When high, the power-up initialization is executed presetting all register bits including this bit.
Note: Bits marked as “1” or “0” are reserved bits and should be written as indicated.
Echo Canceller A, Control Register 2
Echo Canceller B, Control Register 2
ADDRESS = 01h WRITE/READ VERIFY
ADDRESS = 21h WRITE/READ VERIFY
Power Reset Value
CR2
0
0
NLPDis
0
NBDis
HPFDis MuteS
MuteR
0000 0000
7
6
5
4
3
2
1
0
MuteR
MuteS
HPFDis
When high, data on Rout is muted to quiet code. When low, Rout carries active code.
When high, data on Sout is muted to quiet code. When low, Sout carries active code.
When high, the offset nulling high pass filters are bypassed in the Rin and Sin paths.
When low, the offset nulling filters are active and will remove DC offsets on PCM input signals.
NBDis
When high, the narrow-band detector is disabled. When low, the narrow-band detector is enabled.
NLPDis
When high, the non-linear processor is disabled.
When low, the non-linear processors function normally. Useful for G.165 conformance testing.
Note: Bits marked as “0” are reserved bits and should be written as indicated.
19
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Echo Canceller A, Status Register
Echo Canceller B, Status Register
ADDRESS = 02h READ
ADDRESS = 22h READ
Power Reset Value
SR
Down
DTDet
Conv
Active
NB
0000 0000
7
6
5
4
3
2
1
0
NB
Logic high indicates the presence of a narrow-band signal on Rin.
Active
Down
Conv
DTDet
Logic high indicates that the power level on Rin is above the threshold level (i.e., low power condition).
Decision indicator for the non-linear processor gain adjustment.
Decision indicator for rapid adaptation convergence. Logic high indicates a rapid convergence state.
Logic high indicates the presence of a double-talk condition.
20
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Echo Canceller A, Flat Delay Register
Echo Canceller B, Flat Delay Register
ADDRESS = 04h WRITE/READ VERIFY
ADDRESS = 24h WRITE/READ VERIFY
Power Reset Value
00h
FD
FD7
FD6
FD5
FD4
FD3
FD2
FD1
FD0
7
6
5
4
3
2
1
0
Echo Canceller A, Decay Step Number Register
Echo Canceller B, Decay Step Number Register
ADDRESS = 07h WRITE/READ VERIFY
ADDRESS = 27h WRITE/READ VERIFY
Power Reset Value
00h
NS
NS7
NS6
NS5
NS4
NS3
NS2
NS1
NS0
7
6
5
4
3
2
1
0
Echo Canceller A, Decay Step Size Control Register
Echo Canceller B, Decay Step Size Control Register
ADDRESS = 06h WRITE/READ VERIFY
ADDRESS = 26h WRITE/READ VERIFY
Power Reset Value
04h
0
0
0
0
0
SSC2
SSC1
SSC0
SSC
7
6
5
4
3
2
1
0
Note: Bits marked with “0” are reserved bits and should be written “0”.
Amplitude of MU
FIR Filter Length (512 or 1024 taps)
1.0
Step Size (SS)
Flat Delay (FD7-0
)
2-16
Time
The Exponential Decay registers (Decay Step Number and Decay Step Size) and Flat Delay register allow the LMS adaptation
step-size (MU) to be programmed over the length of the FIR filter. A programmable MU profile allows the performance of the echo
canceller to be optimized for specific applications. For example, if the characteristic of the echo response is known to have a flat
delay of several milliseconds and a roughly exponential decay of the echo impulse response, then the MU profile can be
programmed to approximate this expected impulse response thereby improving the convergence characteristics of the adaptive
filter. Note that in the following register descriptions, one tap is equivalent to 125 µs (64 ms/512 taps).
FD7-0
SSC2-0
NS7-0
Flat Delay: This register defines the flat delay of the MU profile, (i.e., where the MU value is 2-16). The delay is defined
as FD7-0 x 8 taps. For example; if FD7-0 = 5, then MU=2-16 for the first 40 taps of the echo canceller FIR filter. The valid
range of FD7-0 is: 0 <= FD7-0 <= 64 in normal mode and 0 <= FD7-0 <= 128 in extended-delay mode. The default value of
FD7-0 is zero.
Decay Step Size Control: This register controls the step size (SS) to be used during the exponential decay of MU. The
decay rate is defined as a decrease of MU by a factor of 2 every SS taps of the FIR filter, where SS = 4 x2SSC2-0. For
example; If SSC2-0 = 4, then MU is reduced by a factor of 2 every 64 taps of the FIR filter. The default value of SSC2-0
is 04h.
Decay Step Number: This register defines the number of steps to be used for the decay of MU where each step has a
period of SS taps (see SSC2-0). The start of the exponential decay is defined as:
Filter Length (512 or 1024) - [ Decay Step Number (NS7-0) x Step Size (SS) ] where SS = 4 x2SSC
.
2-0
For example, if NS7-0=4 and SSC2-0=4, then the exponential decay start value is 512 - [NS7-0 x SS] = 512 - [4 x (4x24)] =
256 taps for a filter length of 512 taps.
21
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Echo Canceller A, Rin Peak Detect Register 2
Echo Canceller B, Rin Peak Detect Register 2
ADDRESS = 0Dh READ
ADDRESS = 2Dh READ
Power Reset Value
N/A
RP15
RP14
RP13
RP12
RP11
RP10
RP9
RP8
RP
7
6
5
4
3
2
1
0
Echo Canceller A, Rin Peak Detect Register 1
Echo Canceller B, Rin Peak Detect Register 1
ADDRESS = 0Ch READ
ADDRESS = 2Ch READ
Power Reset Value
N/A
RP7
RP6
RP5
RP4
RP3
RP2
RP1
RP0
RP
7
6
5
4
3
2
1
0
These peak detector registers allow the user to monitor the receive in signal (Rin) peak signal level. The information is in 16-bit 2’s
complement linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in Register 2 and the low
byte is in Register 1.
Echo Canceller A, Sin Peak Detect Register 2
Echo Canceller B, Sin Peak Detect Register 2
ADDRESS = 0Fh READ
ADDRESS = 2Fh READ
Power Reset Value
N/A
SP11
SP
SP15
SP14
SP13
SP12
SP10
SP9
SP8
7
6
5
4
3
2
1
0
Echo Canceller A, Sin Peak Detect Register 1
Echo Canceller B, Sin Peak Detect Register 1
ADDRESS = 0Eh READ
ADDRESS = 2Eh READ
Power Reset Value
N/A
SP3
SP
SP7
SP6
SP5
SP4
SP2
SP1
SP0
7
6
5
4
3
2
1
0
These peak detector registers allow the user to monitor the send in signal (Sin) peak signal level. The information is in 16-bit 2’s
complement linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in Register 2 and the low
byte is in Register 1.
Echo Canceller A, Error Peak Detect Register 2
Echo Canceller B, Error Peak Detect Register 2
ADDRESS = 11h READ
ADDRESS = 31h READ
Power Reset Value
N/A
EP11
EP
EP15
EP14
EP13
EP12
EP10
EP9
EP8
7
6
5
4
3
2
1
0
Echo Canceller A, Error Peak Detect Register 1
Echo Canceller B, Error Peak Detect Register 1
ADDRESS = 10h READ
ADDRESS = 30h READ
Power Reset Value
N/A
EP3
EP
EP7
EP6
EP5
EP4
EP2
EP1
EP0
7
6
5
4
3
2
1
0
These peak detector registers allow the user to monitor the error signal peak level. The information is in 16-bit 2’s complement
linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in Register 2 and the low byte is in
Register 1.
22
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Echo Canceller A, Double-Talk Detection Threshold Register 2 ADDRESS = 15h WRITE/READ VERIFY
Echo Canceller B, Double-Talk Detection Threshold Register 2 ADDRESS = 35h WRITE/READ VERIFY
Power Reset Value
48h
DTDT
DTDT15 DTDT14 DTDT13 DTDT12 DTDT11 DTDT10
DTDT9 DTDT8
7
6
5
4
3
2
1
0
Echo Canceller A, Double-Talk Detection Threshold Register 1 ADDRESS = 14h WRITE/READ VERIFY
Echo Canceller B, Double-Talk Detection Threshold Register 1
ADDRESS = 34h WRITE/READ VERIFY
Power Reset Value
00h
DTDT7 DTDT6
DTDT5 DTDT4 DTDT3 DTDT2
DTDT1 DTDT0
DTDT
7
6
5
4
3
2
1
0
This register allows the user to program the level of Double-Talk Detection Threshold (DTDT). The 16 bit 2’s complement linear
value defaults to 4800h= 0.5625 or -5 dB. The maximum value is 7FFFh = 0.9999 or 0 dB. The high byte is in Register 2 and
the low byte is in Register 1.
Echo Canceller A, Non-Linear Processor Threshold Register 2 ADDRESS = 19h WRITE/READ VERIFY
Echo Canceller B, Non-Linear Processor Threshold Register 2 ADDRESS = 39h WRITE/READ VERIFY
Power Reset Value
08h
NLPTHR
NLP15
NLP14
NLP13
NLP12
NLP11 NLP10
NLP9
NLP8
7
6
5
4
3
2
1
0
Echo Canceller A, Non-Linear Processor Threshold Register 1 ADDRESS = 18h WRITE/READ VERIFY
Echo Canceller B, Non-Linear Processor Threshold Register 1 ADDRESS = 38h WRITE/READ VERIFY
Power Reset Value
00h
NLP7
NLP6
NLP5
NLP4
NLP3
NLP2
NLP1
NLP0
NLPTHR
7
6
5
4
3
2
1
0
This register allows the user to program the level of the Non-Linear Processor Threshold (NLPTHR). The 16 bit 2’s complement
linear value defaults to 0800h = 0.0625 or -24.1 dB. The maximum value is 7FFFh = 0.9999 or 0 dB. The high byte is in
Register 2 and the low byte is in Register 1.
Echo Canceller A, Adaptation Step Size (MU) Register 2
Echo Canceller B, Adaptation Step Size (MU) Register 2
ADDRESS = 1Bh WRITE/READ VERIFY
ADDRESS = 3Bh WRITE/READ VERIFY
Power Reset Value
40h
MU15
MU14
MU13
MU12
MU11
MU10
MU9
MU8
MU
7
6
5
4
3
2
1
0
Echo Canceller A, Adaptation Step Size (MU) Register 1
Echo Canceller B, Adaptation Step Size (MU) Register 1
ADDRESS = 1Ah WRITE/READ VERIFY
ADDRESS = 3Ah WRITE/READ VERIFY
Power Reset Value
00h
MU7
MU6
MU5
MU4
MU3
MU2
MU1
MU0
MU
7
6
5
4
3
2
1
0
This register allows the user to program the level of MU. MU is a 16 bit 2’s complement value which defaults to 4000h = 1.0
The high byte is in Register 2 and the low byte is in Register 1.
23
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Applications
MT9123 is in SSI mode
MT8910 2B1Q
MT8972 Bi-Phase
MT8931 S-INT
MT9125 ADPCM
MT9123
Sin
DSTo
Sout
DSTi
Din
ADPCMo
T
Dout
ADPCMi
R
ENA
ENB
EN1
EN2
C20
DSTi
BCLK
BCLK
STB1
echo
C4o
F0b
Rout
paths
Rin
DSTo
F0i
MCLK
Dual RF Section
Figure 11 - (Basic Rate ISDN) Wireless Application Diagram
MT9160 5V CODEC
MT9123 is in SSI mode
Dout
T
Din
R
F0i
Clockin
echo
path
MT9125 ADPCM
MT9123
MT9160 5V CODEC
Dout
Sin
Sout
DSTi
ADPCMo
ADPCMi
Din
Dout
T
ENA
ENB
EN1
EN2
C20
R
Din
BCLK
Rin
BCLK
STB1
Clockin
F0i
Rout
echo
path
DSTo
MCLK
F0i
Dual RF Section
MT8941 PLL
F0
C4
Figure 12 - (Analog Trunk) Wireless Application Diagram
24
Zarlink Semiconductor Inc.
MT9123
Data Sheet
MT9160 5V CODEC
MT9123 connected in ST-BUS mode 1
Dout
T
Din
R
F0i
Clockin
echo
path
MT9125 ADPCM
MT9123
MT9160 5V CODEC
Dout
Sin
ADPCMo
ADPCMi
Din
DSTi
Sout
Dout
T
R
Din
Rout
C20
EN1
BCLK
STB1
DSTo
F0i
Rin
Clockin F0i
F0i C4i
echo
path
MCLK
Dual RF Section
MT8941 PLL
F0
C4
Figure 13 - (Analog Trunk) Wireless Application Diagram
MT9123 in ST-BUS mode 1
Back-To-Back Configuration
using D&C channel bypass
MT8910 2B1Q
MT8972 Bi-phase
MT8931 S-INT
MT909x Digital Phone
MT9123
DSTo
Sin
Sout
DSTi
T
R
echo
path
DSTi
Rout
Rin
DSTo
F0i
F0i C4i
C4o F0b
Handset
MCLK
Figure 14 - (Basic Rate ISDN) Wired Telephone Application Diagram
25
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Absolute Maximum Ratings*
Parameter
Symbol
Min.
Max.
Units
1
2
3
4
5
Supply Voltage
V
DD-VSS
Vi/o
-0.3
7.0
V
Voltage on any digital pin
VSS-0.3
VDD+ 0.3
±20
V
Continuous Current on any digital pin
Storage Temperature
Ii/o
mA
°C
TST
PD
-65
150
Package Power Dissipation
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
500
mW
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Supply Voltage
Sym.
Min.
Typ.‡ Max.
Units
Test Conditions
1
2
3
4
5
6
VDD
4.5
2.4
5.0
5.5
VDD
0.4
V
V
TTL Input High Voltage
TTL Input Low Voltage
CMOS Input High Voltage
CMOS Input Low Voltage
Operating Temperature
400mV noise margin
400mV noise margin
VSS
4.5
V
VDD
0.5
V
VSS
-40
V
TA
+85
°C
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
DC Electrical Characteristics* - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Supply Current
Sym.
Min.
Typ.‡
Max.
Units
Conditions/Notes
PWRDN = 0
1
ICC
IDD
100
µA
50
mA PWRDN = 1, clocks active
2
3
4
5
6
7
8
9
Input HIGH voltage (TTL)
Input LOW voltage (TTL)
Input HIGH voltage (CMOS)
Input LOW voltage (CMOS)
Input leakage current
VIH
VIL
2.0
3.5
V
V
All except MCLK,Sin,Rin
All except MCLK,Sin,Rin
MCLK,Sin,Rin
0.8
VIHC
VILC
IIH/IIL
V
1.5
10
V
MCLK,Sin,Rin
0.1
µA
V
VIN=VSS to VDD
IOH=2.5mA
High level output voltage
Low level output voltage
High impedance leakage
VOH 0.9VDD
VOL
IOZ
Co
0.1VDD
10
V
IOL=5.0mA
1
10
8
µA
pF
pF
VIN=VSS to VDD
10 Output capacitance
11 Input capacitance
12 PWRDN
Ci
Positive Threshold Voltage
V+
VH
V-
3.75
V
V
V
Hysteresis
1.0
Negative Threshold Voltage
1.25
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
* DC Electrical Characteristics are over recommended temperature and supply voltage.
26
Zarlink Semiconductor Inc.
MT9123
Data Sheet
AC Electrical Characteristics† - Serial Data Interfaces (see Figures 16 and 17)
Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
MCLK Clock High
Sym.
Min.
Max.
Units
Test Notes
1
2
3
tMCH
tMCL
20
20
ns
ns
MCLK Clock Low
MCLK Frequency
Dual Channel
fDCLK
fSCLK
19.15
9.58
20.5
MHz
MHz
Single Channel
4
5
BCLK/C4i Clock High
BCLK/C4i Clock Low
BCLK/C4i Period
tBCH,
tC4H
90
ns
tBLL,
tC4L
90
ns
6
7
tBCP
tSD
240
7900
80
ns
ns
SSI Enable Strobe to Data Delay (first
bit)
CL=150pF
8
SSI Data Output Delay (excluding first
bit)
tDD
80
80
ns
CL=150pF
CL=150pF
9
SSI Output Active to High Impedance
tAHZ
tSSS
ns
ns
10 SSI Enable Strobe Signal Setup
10
15
tBCP
-15
11 SSI Enable Strobe Signal Hold
tSSH
tBCP
-10
ns
12 SSI Data Input Setup
13 SSI Data Input Hold
14 F0i Setup
tDIS
tDIH
10
15
20
20
ns
ns
ns
ns
ns
ns
tF0iS
tF0iH
tDSD
tASHZ
150
150
80
15 F0i Hold
16 ST-BUS Data Output delay
CL=150pF
CL=150pF
17 ST-BUS Output Active to High
Impedance
80
18 ST-BUS Data Input Hold time
19 ST-BUS Data Input Setup time
20 F0od Delay
tDSH
tDSS
tDFD
tDFW
20
20
ns
ns
ns
ns
80
CL=150pF
CL=150pF
21 F0od Pulse Width Low
† Timing is over recommended temperature and power supply voltages.
200
27
Zarlink Semiconductor Inc.
MT9123
Data Sheet
AC Electrical Characteristics† - Microport Timing (see Figure 16)
Characteristics
Input Data Setup
Sym.
Min.
Max.
Units
Test Notes
1
2
3
4
5
6
7
8
9
tIDS
tIDH
100
30
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input Data Hold
Output Data Delay
Serial Clock Period
SCLK Pulse Width High
SCLK Pulse Width Low
CS Setup-Intel
tODD
tSCP
tSCH
tSCL
100
CL=150pF
500
250
250
200
100
100
tCSSI
tCSSM
tCSH
tOHZ
CS Setup-Motorola
CS Hold
10 CS to Output High Impedance
† Timing is over recommended temperature range and recommended power supply voltages.
100
CL=150pF
Characteristic
TTL reference level
Symbol
TTL Pin
CMOS Pin
Units
VTT
VCT
VH
1.5
-
-
V
V
V
V
V
V
CMOS reference level
0.5*VDD
0.9*VDD
0.1*VDD
0.7*VDD
0.3*VDD
Input HIGH level
2.4
0.4
2.0
0.8
Input LOW level
VL
Rise/Fall HIGH measurement point
VHM
Rise/Fall LOW measurement point
VHL
Table 8 - Reference Level Definition for Timing Measurements
tMCH
VH
VL
MCLK (3)
V
CT
tMCL
Figure 15 - Master Clock - MCLK
Notes: 1. CMOS output
2. TTL input compatible
3. CMOS input
(see Table 8 for symbol definitions)
28
Zarlink Semiconductor Inc.
MT9123
Data Sheet
Bit 0
Bit 1
Sout/Rout (1)
BCLK (2)
CT
TT
TT
CT
V
V
V
V
tSD
tDD
tBCH
tAHZ
VH
VL
tSSS
tBCP
tBCL
tSSH
VH
VL
ENA1/ENA2 (2)
or
ENB1/ENB2 (2)
tDIS
tDIH
Bit 0
Bit 1
VH
VL
Rin/Sin (3)
Figure 16 - SSI Data Port Timing
Notes: 1. CMOS output
2. TTL input compatible
3. CMOS input
(see Table 8 for symbol definitions)
Bit 0
Bit 1
Sout/Rout (1)
V
CT
tDSD tC4H
tASHZ
VH
C4i (2)
V
V
V
V
TT
TT
CT
CT
VL
tF0iS tF0iH
tC4L
VH
F0i (2)
VL
tDSS tDSH
VH
Rin/Sin (3)
VL
Bit 0
Bit 1
tDFD
F0od (1)
tDFW
Figure 17 - ST-BUS Data Port Timing
Notes: 1. CMOS output
2. TTL input compatible
3. CMOS input
(see Table 8 for symbol definitions)
29
Zarlink Semiconductor Inc.
MT9123
Data Sheet
DATA OUTPUT
DATA INPUT
DATA1 (1, 2)
V
V
V
,V
TT CT
tIDS tIDH
tSCH
tODD
tOHZ
VH
VL
SCLK (2)
TT
TT
tCSSI
tSCL
tSCP
tCSH
VH
VL
(
2)
CS
Figure 18 - INTEL Serial Microport Timing
Notes: 1. CMOS output
2. TTL input compatible
3. CMOS input
(see Table 8 for symbol definitions)
VH
DATA2 (2)
V
TT
VL
(Input)
tIDS tIDH
tSCH
tSCP
VH
VL
SCLK (2)
V
TT
tCSSM
tSCL
tCSH
VH
VL
CS (2)
V
TT
tODD
tOHZ
DATA1 (1)
(Output)
V
CT
Figure 19 - MOTOROLA Serial Microport Timing
Notes: 1. CMOS output
2. TTL input compatible
3. CMOS input
(see Table 8 for symbol definitions)
30
Zarlink Semiconductor Inc.
Package Code
c
Zarlink Semiconductor 2005. All rights reserved.
Previous package codes
ISSUE
ACN
DATE
APPRD.
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE
MT9123APR 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
MT9123APR1 | MICROSEMI | ISDN Echo Canceller, 1-Func, CMOS, PQCC28, LEAD FREE, PLASTIC, MS-018AB, LCC-28 | 获取价格 | |
MT9125 | MITEL | CMOS Dual ADPCM Transcoder | 获取价格 | |
MT9125AE | MITEL | CMOS Dual ADPCM Transcoder | 获取价格 | |
MT9125AP | MITEL | CMOS Dual ADPCM Transcoder | 获取价格 | |
MT9126 | MITEL | CMOS Quad ADPCM Transcoder | 获取价格 | |
MT9126AE | MITEL | CMOS Quad ADPCM Transcoder | 获取价格 | |
MT9126AE1 | MICROSEMI | ADPCM Codec, A/MU-Law, 1-Func, CMOS, PDIP28, LEAD FREE, PLASTIC, MS-011AB, DIP-28 | 获取价格 | |
MT9126AS | MITEL | CMOS Quad ADPCM Transcoder | 获取价格 | |
MT9126ASR | ZARLINK | ADPCM Codec, A/MU-Law, 1-Func, CMOS, PDSO28, 0.300 INCH, MS-013AE, SOIC-28 | 获取价格 | |
MT9126ASR | MICROSEMI | Codec, CMOS, PDSO28 | 获取价格 |
MT9123APR 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6