MT93L16AF [MICROSEMI]
ISDN Echo Canceller, 1-Func, CMOS, PQFP48, 7 X 7 MM, 1 MM HEIGHT, MS-026ABC, TQFP-48;
| 型号： | MT93L16AF |
| 厂家： | 
Microsemi |
| 描述： | ISDN Echo Canceller, 1-Func, CMOS, PQFP48, 7 X 7 MM, 1 MM HEIGHT, MS-026ABC, TQFP-48 电信 综合业务数字网 电信集成电路 |
| 文件： | 总36页 (文件大小：456K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MT93L16
AEC for Analog Hands-Free
Communication
Data Sheet
October 2006
Zarlink has introduced a new generation family of
AEC (ZL38002 and ZL38004). Zarlink recommends
these products for new designs.
Ordering Information
MT93L16AQ
MT93L16AF
MT93L16AQ1
36 Pin QSOP
48 Pin TQFP
36 Pin QSOP*
Tubes
Tubes
Tubes
Features
•
Contains two echo cancellers: 112 ms acoustic
*Pb Free Matte Tin
echo canceller + 16 ms line echo canceller
-40C to +85°C
•
Works with low cost voice codec. ITU-T G.711 or
signed mag µ/A-Law, or linear 2’s comp
•
•
•
Serial micro-controller interface
•
•
Each port may operate in different format
ST-BUS, GCI, or variable-rate SSI PCM interfaces
User gain control provided for speaker path
Advanced NLP design - full duplex speech with
no switched loss on audio paths
(-24 dB to +21 dB in 3 dB steps)
AGC on speaker path
•
•
•
•
•
•
Fast re-convergence time: tracks changing echo
environment quickly
•
•
Handles up to 0 dB acoustic echo return loss
Adaptation algorithm converges even during
and 0 dB line ERL
Double-Talk
•
•
•
•
Transparent data transfer and mute options
20 MHz master clock operation
Designed for exceptional performance in high
background noise environments
Low power mode during PCM Bypass
Provides protection against narrow-band signal
Bootloadable for future factory software
divergence
upgrades
Howling prevention stops uncontrolled oscillation
in high loop gain conditions
Offset nulling of all PCM channels
•
2.7 V to 3.6 V supply voltage; 5 V-tolerant
inputs
Limiter
+
µ/A-Law/
ADV
NLP
Linear/
Offset
+
Sin
Sout
Linear
µ/A-Law
Null
-
S2
Program
RAM
DATA1
DATA2
MD1
Micro
Interface
S1
S3
Program
ROM
NBSD
CONTROL
UNIT
Howling
Controller
Adaptive
Filter
Adaptive
Double
Talk
Filter
Detector
NBSD
R3
R1
SCLK
CS
R2
MD2
Rout
-24 -> +21 dB
-
Offset
Null
User
Gain
µ/A-Law/
ADV
NLP
Linear/
µ/A-Law
Rin
AGC
+
Linear
+
Limiter
VSS
VDD
BCLK/C4i
FORMAT
ENA1
MCLK
RESET
ENA2
LAW
F0i
Figure 1 - Functional Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 1999-2006, Zarlink Semiconductor Inc. All Rights Reserved.
MT93L16
Data Sheet
Applications
•
•
•
•
Full duplex speaker-phone for digital telephone
Echo cancellation for video conferencing
Hands-free in automobile environment
Full duplex speaker-phone for PC
MT93L16
ZL38001
ZL38002
ZL38003
Description AEC for analog hands- AEC for analog hands- AEC with noise reduction for digital
AEC with noise reduction & codecs
for digital hands-free communication
free communication free communication hands-free communication
Application Analog Desktop phone Analog Desktop phone Hands-free Car Kits
Hands-free Car Kits
Analog Intercom
Analog Intercom
Digital Desktop Phone Home Security Digital Desktop Phone Home Security
Intercom & Pedestals
Intercom & Pedestals
Features
AEC
1 channel
1 channel
User Gain
1 channel
1 channel
1 channel
1 channel
Custom Load
LEC
Custom Load
Gains
User Gain/18 dB
Gain on Sout
User Gain + System tuning gains
User Gain + System tuning gains
Noise
N
N
N
Y
N
Y
Reduction
Integrated
Codecs
N
dual channel
Table 1 - Acoustic Echo Cancellation Family
2
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
1
2
36 IC
ENA1
35
IC
MD1
34
33
IC
ENA2
3
4
5
36
38
34
32
30
28
26
MCLK2
NC
NC
MCLK2
IC
24
22
20
18
16
14
MD2
Sout
VDD
NC
32
31
30
29
28
27
Rin
VSS
VDD2
VSS2
IC
Sin
6
IC
DATA1
NC
40
42
44
46
48
7
IC
IC
MCLK
8
NC
DATA2
NC
IC
IC
IC
9
QSOP
TQFP
ENA1
NC
IC
10
11
12
13
14
15
CS
26
25
24
23
BCLK/C4i
F0i
MD1
ENA2
MD2
Rin
SCLK
NC
LAW
FORMAT
RESET
NC
Rout
NC
Sout
RESETB
22
VDD
2
4
6
8
10
12
21
20
19
NC
NC
16
17
18
DATA1
DATA2
SCLK
CS
Figure 2 - Pin Connection
Pin Description
QSOP
Pin #
TQFP
Pin #
Name
Description
1
43
ENA1
SSI Enable Strobe / ST-BUS & GCI Mode for Rin/Sout (Input). This pin has
dual functions depending on whether SSI or ST-BUS/GCI is selected. For SSI,
this strobe must be present for frame synchronization. This is an active high
channel enable strobe, 8 or 16 data bits wide, enabling serial PCM data transfer
for on Rin/Sout pins. Strobe period is 125 microseconds. For ST-BUS or GCI,
this pin, in conjunction with the MD1 pin, selects the proper mode for Rin/Sout
pins (see ST-BUS and GCI Operation description).
2
3
45
46
MD1
ST-BUS & GCI Mode for Rin/Sout (Input). When in ST-BUS or GCI operation,
this pin, in conjunction with the ENA1 pin, will select the proper mode for
Rin/Sout pins (see ST-BUS and GCI Operation description). Connect this pin to
Vss in SSI mode.
ENA2
SSI Enable Strobe / ST-BUS & GCI Mode for Sin/Rout (Input).This pin has
dual functions depending on whether SSI or ST-BUS/GCI is selected. For SSI,
this is an active high channel enable strobe, 8 or 16 data bits wide, enabling
serial PCM data transfer on Sin/Rout pins. Strobe period is 125 microseconds.
For ST-BUS/GCI, this pin, in conjunction with the MD2 pin, selects the proper
mode for Sin/Rout pins (see ST-BUS and GCI Operation description).
4
5
47
48
MD2
Rin
ST-BUS & GCI Mode for Sin/Rout (Input).When in ST-BUS or GCI operation,
this pin in conjunction with the ENA2 pin, selects the proper mode for Sin/Rout
pins (see ST-BUS and GCI Operation description). Connect this pin to Vss in SSI
mode.
Receive PCM Signal Input (Input). 128 kbit/s to 4096 kbit/s serial PCM input
stream. Data may be in either companded or 2’s complement linear format. This
is the Receive Input channel from the line (or network) side. Data bits are clocked
in following SSI, GCI or ST-BUS timing requirements.
3
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Pin Description (continued)
QSOP
Pin #
TQFP
Pin #
Name
Description
6
2
Sin
Send PCM Signal Input (Input). 128 kbit/s to 4096 kbit/s serial PCM input
stream. Data may be in either companded or 2’s complement linear format. This
is the Send Input channel (from the microphone). Data bits are clocked in
following SSI, GCI or ST-BUS timing requirements.
7
8
3
5
IC
Internal Connection (Input): Must be tied to Vss.
MCLK Master Clock (Input): Nominal 20 MHz Master Clock input (may be
asynchronous relative to 8 KHz frame signal.) Tie together with MCLK2 (pin 33).
9,10,11
12
6, 7, 8
9
IC
Internal Connection (Input): Must be tied to Vss.
LAW
A/µ Law Select (Input). When low, selects µ−Law companded PCM. When high,
selects A-Law companded PCM. This control is for both serial pcm ports.
13
14
17
18
19
11
13
16
17
19
FORMAT ITU-T/Sign Mag (Input). When low, selects sign-magnitude PCM code. When
high, selects ITU-T (G.711) PCM code. This control is for both serial pcm ports.
RESET Reset / Power-down (Input). An active low resets the device and puts the
MT93L16 into a low-power stand-by mode.
SCLK
CS
Serial Port Synchronous Clock (Input). Data clock for the serial microport
interface.
Serial Port Chip Select (Input). Enables serial microport interface data
transfers. Active low.
DATA2 Serial Data Receive (Input). In Motorola/National serial microport operation, the
DATA2 pin is used for receiving data. In Intel serial microport operation, the
DATA2 pin is not used and must be tied to Vss or Vdd.
20
21
DATA1 Serial Data Port (Bidirectional). In Motorola/National serial microport operation,
the DATA1 pin is used for transmitting data. In Intel serial microport operation,
the DATA1 pin is used for transmitting and receiving data.
22
23
23
24
VDD
Sout
Positive Power Supply (Input). Nominally 3.3 volts.
Send PCM Signal Output (Output). 128 kbit/s to 4096 kbit/s serial PCM output
stream. Data may be in either companded or 2’s complement linear PCM format.
This is the Send Out signal after acoustic echo cancellation and non-linear
processing. Data bits are clocked out following SSI, ST-BUS, or GCI timing
requirements.
24
26
Rout
F0i
Receive PCM Signal Output (Output). 128 kbit/s to 4096 kbit/s serial PCM
output stream. Data may be in either companded or 2’s complement linear PCM
format. This is the Receive out signal after line echo cancellation non-linear
processing, AGC, and gain control. Data bits are clocked out following SSI, ST-
BUS, or GCI timing requirements.
25
26
27
29
Frame Pulse (Input). In ST-BUS (or GCI) operation, this is an active-low (or
active-high) frame alignment pulse, respectively. SSI operation is enabled by
connecting this pin to Vss.
BCLK/C4i Bit Clock/ST-BUS Clock (Input). In SSI operation, BCLK pin is a 128 kHz to
4.096 MHz bit clock. This clock must be synchronous with ENA1, and ENA2
enable strobes.
In ST-BUS or GCI operation, C4i pin must be connected to the 4.096 MHz (C4)
system clock.
4
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Pin Description (continued)
QSOP
Pin #
TQFP
Pin #
Name
Description
27, 28
29
30,31
33
IC
Internal Connection (Input). Tie to Vss.
Digital Ground (Input): Nominally 0 volts.
VSS2
30
34
VDD2 Positive Power Supply (Input): Nominally 3.3 volts (tie together with VDD, pin
22).
31
33
35
38
VSS
Digital Ground (Input): Nominally 0 volts (tie together with VSS2, pin 29).
MCLK2 Master Clock (Input): Nominal 20 MHz master clock (tie together with MCLK,
pin 8).
15,16,2 1, 4, 10,
1,32 12, 14, 15,
18, 20, 22,
NC
No Connect (Output). This pin should be left unconnected.
25, 28, 32,
36, 37, 42,
44
34, 35, 30,40,41
36
IC
Internal Connection (Input). Tie to Vss.
Notes: 1. All inputs have CMOS compatible, 5 V-tolerant logic levels.
2. All outputs have CMOS logic levels. Rout, Sout, and DATA1 are 5 V-tolerant when tristated (to withstand other 5 V drivers
Glossaroyn a shared bus).
Double-Talk
Simultaneous signals present on Rin and Sin.
Signals only present at Sin input.
Near-end Single-Talk
Far-end Single-Talk
ADV NLP
Signals only present at Rin input.
Advanced Non-Linear-Processor
Howling
Oscillation caused by feedback from acoustic and line echo paths
Any mono or dual sinusoidal signals
Narrowband
NBSD
Narrow Band Signal Detector
Noise-Gating
Offset Nulling
Reverberation time
Audible switching of background noise
Removal of DC component
The time duration before an echo level decays to -60 dBm
5
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Changes Summary
The following table captures the changes from the July 2004 issue.
Page
Item
Change
3 and 4
Pin Description Table
Corrected TQFP pinout table. Pin names and descriptions for
pins 16-35, 38-41 and 43 were incorrect.
Functional Description
The MT93L16 device contains two echo cancellers, as well as the many control functions necessary to operate the
echo cancellers. One canceller is for acoustic speaker to microphone echo, and one for line echo cancellation. The
MT93L16 provides clear signal transmission in both audio path directions to ensure reliable voice communication,
even with low level signals. The MT93L16 does not use variable attenuators during double-talk or single-talk
periods of speech, as do many other acoustic echo cancellers for speaker-phones. Instead, the MT93L16 provides
high performance full-duplex operation similar to network echo cancellers, so that users experience clear speech
and un-interrupted background signals during the conversation. This prevents subjective sound quality problems
associated with “noise gating” or “noise contrasting”.
The MT93L16 uses an advanced adaptive filter algorithm that is double-talk stable, which means that convergence
takes place even while both parties are talking1. This algorithm allows continual tracking of changes in the echo
path, regardless of double-talk, as long as a reference signal is available for the echo canceller.
The echo tail cancellation capability of the acoustic echo canceller has been sized appropriately (112 ms) to cancel
echo in an average sized office with a reverberation time of less than 112 ms. The 16 ms line echo canceller is
sufficient to ensure a high ERLE for most line circuits.
In addition to the echo cancellers, the following functions are supported:
•
Control of adaptive filter convergence speed during periods of double-talk, far end single-talk, and near-end
echo path changes.
•
•
•
•
•
•
•
Control of Non-Linear Processor thresholds for suppression of residual non-linear echo.
Howling detector to identify when instability is starting to occur, and to take action to prevent oscillation.
Narrow-Band Detector for preventing adaptive filter divergence caused by narrow-band signals
Offset Nulling filters for removal of DC components in PCM channels.
Limiters that introduce controlled saturation levels.
Serial controller interface compatible with Motorola, National and Intel microcontrollers.
PCM encoder/decoder compatible with µ/A-Law ITU-T G.711, µ/A-Law Sign-Mag or linear 2’s complement
coding.
•
Automatic gain control on the receive speaker path.
Adaptation Speed Control
The adaptation speed of the acoustic echo canceller is designed to optimize the convergence speed versus
divergence caused by interfering near-end signals. Adaptation speed algorithm takes into account many different
factors such as relative double-talk condition, far end signal power, echo path change and noise levels to achieve
fast convergence.
1. Patented.
6
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Advanced Non-Linear Processor (ADV-NLP)1
After echo cancellation, there is likely to be residual echo which needs to be removed so that it will not be audible.
The MT93L16 uses an NLP to remove low level residual echo signals which are not comprised of background
noise. The operation of the NLP depends upon a dynamic activation threshold, as well as a double-talk detector
which disables the NLP during double-talk periods.
The MT93L16 keeps the perceived noise level constant, without the need for any variable attenuators or gain
switching that causes audible “noise gating”. The noise level is constant and identical to the original background
noise even when the NLP is activated.
For each audio path, the NLP can be disabled by setting the NLP- bit to 1 in the LEC or AEC control registers.
Narrow Band Signal Detector (NBSD)2
Single or multi-frequency tones (e.g., DTMF, or signalling tones) present in the reference input of an echo canceller
for a prolonged period of time may cause the adaptive filter to diverge. The Narrow Band Signal Detector (NBSD) is
designed to prevent this divergence by detecting single or multi-tones of arbitrary frequency, phase, and amplitude.
When narrow band signals are detected, the filter adaptation process is stopped but the echo canceller continues to
cancel echo.
The NBSD can be disabled by setting the NB- bit to 1 in the MC control registers.
Howling Detector (HWLD)3
The Howling detector is part of an Anti-Howling control, designed to prevent oscillation as a result of positive
feedback in the audio paths.
The HWLD can be disabled by setting the AH- bit to 1 in the (MC) control register.
Offset Null Filter
To ensure robust performance of the adaptive filters at all times, any DC offset that may be present on either the
Rin signal or the Sin signal, is removed by highpass filters. These filters have a corner frequency placed at 40 Hz.
The offset null filters can be disabled by setting the HPF- bit to 1 in the LEC or AEC control registers.
Limiters
To prevent clipping in the echo paths, two limiters with variable thresholds are provided at the outputs.
The Rout limiter threshold is in Rout Limiter Register 1 and 2. The Sout limiter threshold is in Sout Limiter Register.
Both output limiters are always enabled.
User Gain
The user gain function provides the ability for users to adjust the audio gain in the receive path (speaker path). This
gain is adjustable from -24 dB to +21 dB in 3 dB steps. It is important to use ONLY this user gain function to adjust
the speaker volume. The user gain function in the MT93L16 is optimally placed between the two echo cancellers
such that no reconvergence is necessary after gain changes.
The gain can be accessed through Receive Gain Control Register.
1. Patented.
2. Patented.
3. Patented.
7
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
AGC
The AGC function is provided to limit the volume in the speaker path. The gain of the speaker path is automatically
reduced during the following conditions:
•
•
•
When clipping of the receive signal occurs.
When initial convergence of the acoustic echo canceller detects unusually large echo return.
When howling is detected.
The AGC can be disabled by setting the AGC- bit to 1 in MC control register.
Mute Function
A pcm mute function is provided for independent control of the Receive and Send audio paths. Setting the MUTE_R
or MUTE_S bit in the MC register, causes quiet code to be transmitted on the Rout or Sout paths respectively.
Quiet code is defined according to the following table:
LINEAR
16 bits
SIGN/
MAGNITUDE
µ-Law
CCITT (G.711)
2’s
µ-Law
FFh
A-Law
complement
A-Law
+Zero
(quiet
code)
0000h
80h
D5h
Table 2 - Quiet PCM Code Assignment
Bypass Control
A PCM bypass function is provided to allow transparent transmission of pcm data through the MT93L16. When the
bypass function is active, pcm data passes transparently from Rin to Rout and from Sin to Sout, with bit-wise
integrity preserved.
When the Bypass function is selected, most internal functions are powered down to provide low power
consumption.
The BYPASS control bit is located in the main control MC register.
Adaptation Enable/Disable
Adaptation control bits are located in the AEC and LEC control registers. When the ADAPT- bit is set to 1, the
adaptive filter is frozen at the current state. In this state, the device continues to cancel echo with the current echo
model.
When the ADAPT- bit is set to 0, the adaptive filter is continually updated. This allows the echo canceller to adapt
and track changes in the echo path. This is the normal operating state.
MT93L16 Throughput Delay
In all modes, voice channels always have 2 frames of delay. In ST-BUS/GCI operation, the D and C channels have
a delay of one frame.
Power Down / Reset
Holding the RESET pin at logic low will keep the MT93L16 device in a power-down state. In this state all internal
clocks are halted, and the DATA1, Sout and Rout pins are tristated.
8
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
The user should hold the RESET pin low for at least 200 msec following power-up. This will insure that the device
powers up in a proper state. Following any return of RESET to logic high, the user must wait for 8 complete 8 KHz
frames prior to writing to the device registers. During this time, the initialization routines will execute and set the
MT93L16 to default operation (program execution from ROM using default register values).
PCM Data I/O
The PCM data transfer for the MT93L16 is provided through two PCM ports. One port consists of Rin and Sout pins
while the second port consists of Sin and Rout pins. The data are transferred through these ports according to
either ST-BUS, GCI, or SSI conventions, and the device automatically detects the correct convention. The device
determines the convention by monitoring the signal applied to the F0i pin. When a valid ST-BUS (active low) frame
pulse is applied to the F0i pin, the MT93L16 will assume ST-BUS operation. When a valid GCI (active high) frame
pulse is applied to the F0i pin, the device will assume GCI operation. If F0i is tied continuously to Vss, the device
will assume SSI operation. Figures 11 to 13 show timing diagrams of these 3 PCM-interface operation conventions.
ST-BUS and GCI Operation
The ST-BUS PCM interface conforms to Zarlink’s ST-BUS standard, with an active-low frame pulse. Input data is
clocked in by the rising edge of the bit clock (C4i) three-quarters of the way into the bitcell, and output data bit
boundaries (Rout, Sout) occur every second falling edge of the bit clock (see Figure 11.) The GCI PCM interface
corresponds to the GCI standard commonly used in Europe, with an active-high frame pulse. Input data is clocked
in by the falling edge of the bit clock (C4i) three-quarters of the way into the bitcell, and output data bit boundaries
(Rout, Sout) occur every second rising edge of the bit clock (see Figure 12.)
Either of these interfaces (STBUS or GCI) can be used to transport 8 bit companded PCM data (using one timeslot)
or 16 bit 2’s complement linear PCM data (using two timeslots). The MD1/ENA1 pins select the timeslot on the
Rin/Sout port while the MD2/ENA2 pin selects the timeslot on the Sin/Rout port, as in Table 3. Figures 3 to 6
illustrate the timeslot allocation for each of these four modes.
PORT1
ST-BUS/GCI Mode
Selection
PORT2
Rin/Sout
Sin/Rout
Enable Pins
Enable Pins
MD1
ENA1
MD2
ENA2
0
0
1
0
1
0
Mode 1. 8 bit companded PCM I/O on timeslot 0
Mode 2. 8 bit companded PCM I/O on timeslot 2.
0
0
1
0
1
0
Mode 3. 8 bit companded PCM I/O on timeslot 2.
Includes D & C channel bypass in timeslots 0 &
1.
1
1
Mode 4. 16 bit 2’s complement linear PCM I/O
on timeslots 0 & 1.
1
1
Table 3 - ST-BUS & GCI Mode Select
9
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
C4i
start of frame (stbus & GCI)
F0i (ST-BUS)
F0i (GCI)
0
B
1
2
3
4
PORT1
Rin
7 6 5 4 3 2 1 0
EC
Sout
7 6 5 4 3 2 1 0
PORT2
Sin
7 6 5 4 3 2 1 0
EC
7 6 5 4 3 2 1 0
Rout
outputs = High impedance
inputs = don’t care
In ST-BUS/GCI Mode 1, echo canceller I/O channels are assigned to ST-BUS/GCI timeslot 0. Note that the user can configure PORT1
and PORT2 into different modes.
Figure 3 - ST-BUS and GCI 8-Bit Companded PCM I/O on Timeslot 0 (Mode 1)
C4i
start of frame (stbus & GCI)
F0i (ST-BUS)
0
1
2
3
4
B
F0i (GCI)
PORT1
Rin
7 6 5 4 3 2 1 0
EC
Sout
7 6 5 4 3 2 1 0
PORT2
Sin
7 6 5 4 3 2 1 0
EC
7 6 5 4 3 2 1 0
Rout
outputs = High impedance
inputs = don’t care
In ST-BUS/GCI Mode 2, echo canceller I/O channels are assigned to ST-BUS/GCI timeslot 2. Note that the user can configure PORT1
and PORT2 into different modes.
Figure 4 - ST-BUS and GCI 8-Bit Companded PCM I/O on Timeslot 2 (Mode 2)
10
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
C4i
start of frame (stbus & GCI)
F0i (ST-BUS)
0
1
2
3
4
B
C
D
F0i (GCI)
PORT1
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Rin
EC
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Sout
PORT2
Sin
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
EC
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Rout
outputs = High impedance
inputs = don’t care
indicates that an input channel is bypassed to an output channel
ST-BUS/GCI Mode 3 supports connection to 2B+D devices where timeslots 0 and 1 transport D and C channels and echo canceller
(EC) I/O channels are assigned to ST-BUS timeslot 2 (B). Both PORT1 and PORT2 must be configured in Mode 3.
Figure 5 - ST-BUS and GCI 8-Bit Companded PCM I/O with D and C Channels (Mode 3)
C4i
start of frame (stbus & GCI)
F0i (stbus)
F0i (GCI)
Rin
S 141312 1110 9 8 7 6 5 4 3 2 1 0
PORT1
EC
S 141312 1110 9 8 7 6 5 4 3 2 1 0
Sout
Sin
S 141312 1110 9 8 7 6 5 4 3 2 1 0
PORT2
EC
S 141312 1110 9 8 7 6 5 4 3 2 1 0
Rout
outputs = High impedance
inputs = don’t care
ST-BUS/GCI Mode 4 allows 16 bit 2’s complement linear data to be transferred using ST-BUS/GCI I/O timing. Note that PORT1 and
PORT2 need not necessarily both be in mode 4.
Figure 6 - ST-BUS and GCI 16-Bit 2’s Complement Linear PCM I/O (Mode 4)
11
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
SSI Operation
The SSI PCM interface consists of data input pins (Rin, Sin), data output pins (Sout, Rout), a variable rate bit clock
(BCLK), and two enable pins (ENA1, ENA2) to provide strobes for data transfers. The active high enable may be
either 8 or 16 BCLK cycles in duration. Automatic detection of the data type (8 bit companded or 16 bit 2’s
complement linear) is accomplished internally. The data type cannot change dynamically from one frame to the
next.
In SSI operation, the frame boundary is determined by the rising edge of the ENA1 enable strobe (see Figure 7).
The other enable strobe (ENA2) is used for parsing input/output data and it must pulse within 125 microseconds of
the rising edge of ENA1.
In SSI operation, the enable strobes may be a mixed combination of 8 or 16 BCLK cycles allowing the flexibility to
mix 2’s complement linear data on one port (e.g., Rin/Sout) with companded data on the other port (e.g., Sin/Rout).
Enable Strobe Pin
Designated PCM I/O Port
ENA1
ENA2
Line Side Echo Path (PORT 1)
Acoustic Side Echo Path (PORT 2)
Table 4 - SSI Enable Strobe Pins
PCM Law and Format Control (LAW, FORMAT)
The PCM companding/coding law used by the MT93L16 is controlled through the LAW and FORMAT pins. ITU-T
G.711 companding curves for µ-Law and A-Law are selected by the LAW pin. PCM coding ITU-T G.711 and Sign-
Magnitude are selected by the FORMAT pin. See Table 5.
12
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
BCLK
start of frame (SSI)
PORT1
ENA1
8 or 16 bits
Rin
EC
Sout
8 or 16 bits
PORT2
ENA2
8 or 16 bits
Sin
EC
8 or 16 bits
Rout
outputs = High impedance
inputs = don’t care
Note that the two ports are independent so that, for example, PORT1 can operate with 8-bit enable strobes and PORT2 can operate
with 16-bit enable strobes.
Figure 7 - SSI Operation
Sign-Magnitude
FORMAT=0
ITU-T (G.711)
FORMAT=1
PCM Code
µ/A-LAW
µ-LAW
A-LAW
LAW = 0 or 1
LAW = 0
LAW =1
+ Full Scale
+ Zero
1111 1111
1000 0000
0000 0000
0111 1111
1000 0000
1111 1111
0111 1111
0000 0000
1010 1010
1101 0101
0101 0101
0010 1010
- Zero
- Full Scale
Table 5 - Companded PCM
13
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Linear PCM
The 16-bit 2’s complement PCM linear coding permits a dynamic range beyond that which is specified in ITU-T
G.711 for companded PCM. The echo-cancellation algorithm will accept 16 bits 2’s complement linear code which
gives a maximum signal level of +15 dBm0.
Bit Clock (BCLK/C4i)
The BCLK/C4i pin is used to clock the PCM data for GCI and ST-BUS (C4i) interfaces, as well as for the SSI
(BCLK) interface.
In SSI operation, the bit rate is determined by the BCLK frequency. This input must contain either eight or sixteen
clock cycles within the valid enable strobe window. BCLK may be any rate between 128 KHz to 4.096 MHz and can
be discontinuous outside of the enable strobe windows defined by ENA1, ENA2 pins. Incoming PCM data (Rin, Sin)
are sampled on the falling edge of BCLK while outgoing PCM data (Sout, Rout) are clocked out on the rising edge
of BCLK. See Figure 13.
In ST-BUS and GCI operation, connect the system C4 (4.096 MHz) clock to the C4i pin.
Master Clock (MCLK)
A nominal 20 MHz, continuously-running master clock (MCLK) is required. MCLK may be asynchronous with the
8 KHz frame.
Microport
The serial microport provides access to all MT93L16 internal read and write registers, plus write-only access to the
bootloadable program RAM (see next section for bootload description.) This microport is compatible with Intel
MCS-51 (mode 0), Motorola SPI (CPOL=0, CPHA=0), and National Semiconductor Microwire specifications. The
microport consists of a transmit/receive data pin (DATA1), a receive data pin (DATA2), a chip select pin (CS) and a
synchronous data clock pin (SCLK).
The MT93L16 automatically adjusts its internal timing and pin configuration to conform to Intel or Motorola/National
requirements. The microport dynamically senses the state of the SCLK pin each time CS pin becomes active (i.e.
high to low transition). If SCLK pin is high during CS activation, then Intel mode 0 timing is assumed. In this case
DATA1 pin is defined as a bi-directional (transmit/receive) serial port and DATA2 is internally disconnected. If SCLK
is low during CS activation, then Motorola/National timing is assumed and DATA1 is defined as the data transmit pin
while DATA2 becomes the data receive pin. The MT93L16 supports Motorola half-duplex processor mode
(CPOL=0 and CPHA=0). This means that during a write to the MT93L16, by the Motorola processor, output data
from the DATA1 pin must be ignored. This also means that input data on the DATA2 pin is ignored by the MT93L16
during a valid read by the Motorola processor.
All data transfers through the microport are two bytes long. This requires the transmission of a Command/Address
byte followed by the data byte to be written to or read from the addressed register. CS must remain low for the
duration of this two-byte transfer. As shown in Figures 8 and 9, the falling edge of CS indicates to the MT93L16 that
a microport transfer is about to begin. The first 8 clock cycles of SCLK after the falling edge of CS are always used
to receive the Command/Address byte from the microcontroller. The Command/Address byte contains information
detailing whether the second byte transfer will be a read or a write operation and at what address. The next 8 clock
cycles are used to transfer the data byte between the MT93L16 and the microcontroller. At the end of the two-byte
transfer, CS is brought high again to terminate the session. The rising edge of CS will tri-state the DATA1 pin. The
DATA1 pin will remain tri-stated as long as CS is high.
Intel processors utilize Least Significant Bit (LSB) first transmission while Motorola/National processors use Most
Significant Bit (MSB) first transmission. The MT93L16 microport automatically accommodates these two schemes
for normal data bytes. However, to ensure timely decoding of the R/W and address information, the
Command/Address byte is defined differently for Intel and Motorola/National operations. Refer to the relative timing
14
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
diagrams of Figure 8 and Figure 9. Receive data bits are sampled on the rising edge of SCLK while transmit data is
clocked out on the falling edge of SCLK. Detailed microport timing is shown in Figure 14 and Figure 15.
Bootload Process and Execution from RAM
A bootloadable program RAM (BRAM) is available on the MT93L16 to support factory-issued software upgrades to
the built-in algorithm. To make use of this bootload feature, users must include 4096 X 8 bits of memory in their
microcontroller system (i.e., external to the MT93L16), from which the MT93L16 can be bootloaded. Registers and
program data are loaded into the MT93L16 in the same fashion via the serial microport. Both employ the same
command / address / data byte specification described in the previous section on serial microport. Either intel or
motorola mode may be transparently used for bootloading. There are also two registers relevant to bootloading
(BRC=control and SIG=signature, see Register Summary). The effect of these register values on device operation
is summarized in Table 6.
FUNCTIONAL DESCRIPTION FOR USING THE BOOTABLE RAM
BOOTLOAD MODE - Microport Access is to bootload RAM (BRAM)
R/W
Data
Address
W
3fh
Writes "data" to BRC reg.
BRC Register
Bits
(= 1 1 1 1 1 1 b)
- Bootload frozen; BRAM contents are NOT affected.
C3C2C1C0
W
R
other than 3fh
1 x x x x x b
Writes "data" to next byte in BRAM (bootloading.)
X 1 0 0
Reads back "data" = BRC reg value.
- Bootload frozen; BRAM contents are NOT affected.
R
0 x x x x x b
Reads back "data" = SIG reg value.
- Bootload frozen; BRAM contents are NOT affected.
NON-BOOTLOAD MODE - Microport Access is to device registers (DREGs)
BRC Register
Bits
R/W
Data
Address
C3C2C1C0
W
any
Writes "data" to corresponding DREG.
(= a5 a4 a3 a2 a1 a0 b)
X 0 0 0
R
any
Reads back "data" = corresponding DREG value.
(= a5 a4 a3 a2 a1 a0 b)
PROGRAM EXECUTION MODES
Execute program in ROM, bootload mode disabled.
- BRAM address counter reset to initial (ready) state.
- SIG reg reseeded to initial (ready) state
C3C2C1C0
0
0 0 0
C3C2C1C0
Execute program in ROM, while bootloading the RAM.
- BRAM address counter increments on microport writes (except to 3fh)
- SIG reg recalculates signature on microport writes (except to 3fh)
0
1 0 0
C3C2C1C0
Execute program in RAM, bootload mode disabled.
- BRAM address counter reset to initial (ready) state.
- SIG reg reseeded to initial (ready) state
1
0 0 0
C3C2C1C0
- NOT RECOMMENDED -
1
1
0
0
(Execute program in RAM, while bootloading the RAM)
Table 6 - Bootload RAM Control (BRC) Register States
Note: bits C1 C0 are reserved, and must be set to zero.
15
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Bootload mode is entered and exited by writing to the bootload bit in the Bootload RAM Control (BRC) register at
address 3fh (see Register Summary). During bootload mode, any serial microport "write" (R/W command bit =0) to
an address other than that of the BRC register will contribute to filling the program BRAM. Call these transactions
"BRAM-fill" writes. Although a command/address byte must still precede each data byte (as described for the serial
microport), the values of the address fields for these "BRAM-fill" writes are ignored (except for the value 3fh, which
designates the BRC register.) Instead, addresses are internally generated by the MT93L16 for each "BRAM-fill"
write. Address generation for "BRAM-fill" writes resumes where it left off following any read transaction while
bootload mode is enabled. The first 4096 such "BRAM-fill" writes while bootload is enabled will load the memory,
but further ones after that are ignored. Following the write of the first 4096 bytes, the program BRAM will be filled.
Before bootload mode is disabled, it is recommended that users then read back the value from the signature
register (SIG) and compare it to the one supplied by the factory along with the code. Equality verifies that the
correct data has been loaded. The signature calculation uses an 8-bit MISR which only incorporates input from
"BRAM-fill" writes. Resetting the bootload bit (C2) in the BRC register to 0 (see Register Summary) exits bootload
mode, resetting the signature (SIG) register and internal address generator for the next bootload. A hardware reset
(RESET=0) similarly returns the MT93L16 to the ready state for the start of a bootload.
Once the program has been loaded, to begin execution from RAM, bootload mode must be disabled (BOOT bit,
C2=0) and execution from RAM enabled (RAM_ROMb bit, C3=1) by setting the appropriate bits in the BRC register.
During the bootload process, however, ROM program execution (RAM_ROMb bit, C3=0) should be selected. See
Table 6 for the effect of the BRC register settings on Microport accesses and on program execution.
Following program loading and enabling of execution from RAM, it is recommended that users set the software
reset bit in the Main Control (MC) register, to ensure that the device updates the default register values to those of
the new program in RAM. Note: it is important to use a software reset rather than a hardware (RESET=0) reset, as
the latter will return the device to its default settings (which includes execution from program ROM instead of RAM.)
To verify which code revision is currently running, users can access the Firmware Revision Code (FRC) register
(see Register Summary). This register reflects the identity code (revision number) of the last program to run register
initialization (which follows a software or hardware reset.)
COMMAND/ADDRESS e
DATA INPUT/OUTPUT
A0 A1 A2 A3 A4 A5
X
D0 D1 D2 D3 D4 D5 D6 D7
R/W
DATA 1
a
b
SCLK
CS
d
c
a
This delay is due to internal processor timing and is equal to Tsch time. The delay is transparent to MT93L16.
b
The MT93L16: latches receive data on the rising edge of SCLK
outputs transmit data on the falling edge of SCLK
c
The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent
byte is always data followed by CS returning high.
A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again.
d
e
The COMMAND/ADDRESS byte contains: 1 bit - Read/Write
6 bits - Addressing Data
1 bit - Unused
Figure 8 - Serial Microport Timing for Intel Mode 0
16
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
COMMAND/ADDRESS e
DATA INPUT
DATA 2
Receive
R/W A5 A4 A3 A2 A1 A0
High Impedance
X
D7 D6 D5 D4 D3 D2 D1 D0
DATA OUTPUT
DATA 1
D7 D6 D5 D4 D3 D2 D1 D0
Transmit
a
b
SCLK
CS
d
c
a
This delay is due to internal processor timing and is equal to Tsch time. The delay is transparent to MT93L16.
b
The MT93L16: latches receive data on the rising edge of SCLK
outputs transmit data on the falling edge of SCLK
c
The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent
byte is always data followed by CS returning high.
A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again.
d
e
The COMMAND/ADDRESS byte contains: 1 bit - Read/Write
6 bits - Addressing Data
1 bit - Unused
Figure 9 - Serial Microport Timing for Motorola Mode 00 or National Microwire
17
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Absolute Maximum Ratings*
Parameter
Symbol
Min.
Max.
Units
1
2
3
4
5
6
Supply Voltage
Input Voltage
V
DD-VSS
Vi
-0.5
5.0
5.5
V
V
VSS-0.3
VSS-0.3
Output Voltage Swing
Vo
5.5
V
Continuous Current on any digital pin
Storage Temperature
Ii/o
±20
mA
°C
mW
TST
PD
-65
150
Package Power Dissipation
90 (typ)
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
.
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated
Characteristics
Supply Voltage
Sym.
Min.
Typ. Max. Units
Test Conditions
1
2
3
4
VDD
2.7
1.4
VSS
-40
3.3
3.6
VDD
0.4
V
V
Input High Voltage
Input Low Voltage
V
Operating Temperature
TA
+85
°C
Echo Return Limits
Characteristics
Min.
Typ. Max. Units
Test Conditions
1
2
Acoustic Echo Return
Line Echo Return
0
0
dB
dB
Measured from Rout -> Sin
Measured from Sout -> Rin
DC Electrical Characteristics*- Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
Typ‡.
Max.
Units
Conditions/Notes
RESET = 0
Standby Supply Current:
Operating Supply Current:
Input HIGH voltage
ICC
IDD
VIH
VIL
3
70
µA
mA
V
1
20
RESET = 1, clocks active
2
3
4
5
6
7
8
9
0.7VDD
0.8VDD
Input LOW voltage
0.3VDD
10
V
Input leakage current
High level output voltage
Low level output voltage
High impedance leakage
Output capacitance
IIH/IIL
VOH
VOL
IOZ
0.1
µA
V
VIN=VSS to VDD
IOH=2.5 mA
0.4VDD
10
V
IOL=5.0 mA
1
10
8
µA
pF
pF
VIN=VSS to VDD
Co
Input capacitance
Ci
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
*DC Electrical Characteristics are over recommended temperature and supply voltage.
18
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
AC Electrical Characteristics† - Serial Data Interfaces - Voltages are with respect to ground (VSS) unless otherwise stated
Characteristics
MCLK Frequency
Sym.
Min.
Typ.
Max.
Units
Test Notes
1
2
fCLK
19.15
90
20.5
MHz
ns
BCLK/C4i Clock High
BCLK/C4i Clock Low
BCLK/C4i Period
tBCH,
tC4H
3
tBLL,
tC4L
90
ns
4
5
tBCP
tSD
240
80
7900
ns
ns
SSI Enable Strobe to Data Delay
(first bit)
CL=150 pF
6
7
8
9
SSI Data Output Delay (excluding
first bit)
tDD
tAHZ
tSSS
tSSH
80
80
10
15
ns
ns
ns
ns
CL=150 pF
CL=150 pF
SSI Output Active to High
Impedance
SSI Enable Strobe Signal Setup
tBCP
-15
SSI Enable Strobe Signal Hold
tBCP
-10
10 SSI Data Input Setup
11 SSI Data Input Hold
tDIS
tDIH
10
15
20
20
80
80
ns
ns
ns
ns
ns
ns
12 ST-BUS/GCI F0i Setup
13 ST-BUS/GCI F0i Hold
14 ST-BUS/GCI Data Output delay
tF0iS
tF0iH
tDSD
tASHZ
150
150
CL=150 pF
CL=150 pF
15 ST-BUS/GCI Output Active to High
Impedance
16 ST-BUS/GCI Data Input Hold time
tDSH
tDSS
20
20
ns
ns
17 ST-BUS/GCI Data Input Setup time
† Timing is over recommended temperature and power supply voltages.
19
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
AC Electrical Characteristics† - Microport Timing
Characteristics
Input Data Setup
Sym.
Min.
Typ.
Max. Units
Test Notes
1
2
3
4
5
6
7
8
9
tIDS
tIDH
30
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Input Data Hold
30
Output Data Delay
Serial Clock Period
SCLK Pulse Width High
SCLK Pulse Width Low
CS Setup-Intel
tODD
tSCP
tSCH
tSCL
tCSSI
tCSSM
tCSH
tOHZ
100
500
250
250
200
100
100
100
CL=150 pF
CS Setup-Motorola
CS Hold
10 CS to Output High Impedance
† Timing is over recommended temperature range and recommended power supply voltages.
CL=150 pF
Characteristic
CMOS reference level
Symbol
CMOS Level
Units
VCT
VH
0.5*VDD
0.9*VDD
0.1*VDD
0.7*VDD
0.3*VDD
V
V
V
V
V
Input HIGH level
Input LOW level
VL
Rise/Fall HIGH measurement point
Rise/Fall LOW measurement point
VHM
VLM
Table 7 - Reference Level Definition for Timing Measurements
T=1/fCLK
VH
VL
MCLK (I)
V
CT
Notes: O. CMOS output
I. CMOS input (5 V tolerant)
(see Table 8 for symbol definitions)
Figure 10 - Master Clock - MCLK
20
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Bit 7
Bit 6
Sout/Rout (O)
V
CT
tASHZ
tDSD
tC4H
VH
VL
C4i (I)
V
CT
tF0iS tF0iH
tC4L
VH
VL
F0i (I)
V
CT
tDSS tDSH
start of frame
VH
VL
Rin/Sin (I)
V
CT
Bit 6
Bit 7
Figure 11 - GCI Data Port Timing
)
Bit 7
Bit 6
Sout/Rout (O)
V
CT
tDSD
tC4H
tASHZ
VH
VL
C4i (I)
V
CT
tF0iS tF0iH
tC4L
VH
VL
F0i (I)
V
CT
start of frame
tDSS tDSH
VH
VL
Rin/Sin (I)
V
CT
Bit 6
Bit 7
Figure 12 - ST-BUS Data Port Timing
21
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Bit 7
Bit 6
Bit 5
Sout/Rout (O)
BCLK (I)
CT
CT
CT
CT
V
V
V
V
tAHZ
tSD
tDD
tBCH
VH
VL
tSSS
tBCP
tBCL
tSSH
VH
VL
ENA1 (I)
or
ENA2 (I)
tDIS
tDIH
start of frame
VH
VL
Rin/Sin (1)
Bit 7
Bit 6
Bit 5
Notes: O. CMOS output
I. CMOS input (5 V tolerant)
(see Table 8 for symbol definitions)
Figure 13 - SI Data Port Timing
DATA OUTPUT
DATA INPUT
DATA1 (I,O)
V
V
V
CT
CT
CT
tIDS tIDH
tSCH
tODD
tOHZ
VH
SCLK (I)
VL
tCSSI
tSCL
tSCP
tCSH
VH
(
I)
CS
VL
Notes: O. CMOS output
I. CMOS input (5 V tolerant)
(see Table 8 for symbol definitions)
Figure 14 - INTEL Serial Microport Timing
22
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
VH
VL
DATA2 (I)
(Input)
V
CT
CT
CT
CT
tIDS tIDH
tSCH
tSCP
VH
VL
SCLK (I)
V
V
V
tCSSM
tSCL
tCSH
VH
VL
CS (I)
tODD
tOHZ
DATA1 (O)
(Output)
Notes: O. CMOS output
I. CMOS input (5 V tolerant)
(see Table 8 for symbol definitions)
Figure 15 - Motorola Serial Microport Timing
23
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Register Summary
Address:
00h R/W
Main Control Register (MC)
Power Up
7
6
5
4
3
2
1
0
MUTE_S
LIMIT
BYPASS
AGC-
AH-
MUTE_R
NB-
RESET
LSB
Reset 00h
RESET
MSB
When high, the power initialization routine is executed presetting all registers to default values.
This bit automatically clears itself to’0’ when reset is complete.
AH-
AGC-
When high, the Howling detector is disabled and when low the Howling detector is enabled.
When high, AGC is disabled and when low AGC is enabled.
NB-
When high, Narrowband signal detectors in Rin and Sin paths are disabled and when low the signal detectors are enabled
BYPASS
When high, the Send and Receive paths are transparently by-passed from input to output and when low the Send and
Receive paths are not bypassed
MUTE_S
MUTE_R
LIMIT
When high, the Sin path is muted to quite code (after the NLP) and when low the Sin path is not muted
When high, the Rin path is muted to quite code (after the NLP) and when low the Rin path is not muted
When high, the 2-bit shift mode is enabled in conjunction with bit 7 of LEC register and when low 2-bit shift mode is
disabled
Address:
21h R/W
Acoustic Echo Canceller Control Register (AEC)
Power Up
Reset 00h
7
6
5
4
3
2
HCLR
1
0
ECBY
P-
HPF-
NLP-
INJ-
ASC-
ADAPT-
MSB
LSB
ECBY
ADAPT-
HCLR
HPF-
INJ-
When high, the Echo estimate from the filter is not subtracted from the input (Sin), when low the estimate is subtracted
When high, the Echo canceller adaptation is disabled and when low the adaptation is enabled
When high, Adaptive filter coefficients are cleared and when low the filter coefficients are not cleared
When high, Offset nulling filter is bypassed in the Sin/Sout path and when low the Offset nulling filter in not bypassed
When high, the Noise filtering process is disabled in the NLP and when low the Noise filtering process is enabled
When high, the Non Linear Processor is disabled in the Sin/Sout path and when low the NLP is enabled
When high, the Internal Adaptation speed control is disabled and when low the Adaptation speed is enabled
NLP-
ASC-
P-
When high, the Exponential weighting function for the adaptive filter is disabled and when low the weighting function is
enabled
Address:
01h R/W
Line Echo Canceller Control Register (LEC)
Power Up
Reset 00h
7
6
5
4
3
2
HCLR
1
0
ECBY
HPF-
SHFT
NLP-
INJ-
ASC-
ADAPT-
MSB
LSB
ECBY
ADAPT-
HCLR
HPF-
When high, the Echo estimate from the filter is not substracted from the input (Rin), when low the estimate is substracted
When high, the Echo canceller adaptation is disabled and when low the adaptation is enabled
When high, Adaptive filter coefficients are cleared and when low the filter coefficients are not cleared
When high, Offset nulling filter is bypassed in the Rin/Rout path and when low the Offset nulling filter in not bypassed
When high, the Noise filtering process is disabled in the NLP and when low the Noise filtering process is enabled
When high, the Non Linear Processor is disabled in the Rin/Rout path and when low the NLP is enabled
When high, the Internal Adaptation speed control is disabled and when low the Adaptation speed is enabled
INJ-
NLP-
ASC-
SHFT
when high the 16-bit linear mode, inputs Sin, Rin, are shift right by 2 and outputs Sout, Rout are shift left by 2. This bit is
ignored when 16-bit linear mode is not selected in both ports. This bit is also ignored if bit 7 of MC register is set to zero
24
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
22h Read
Acoustic Echo Canceller Status Register (ASR) (* Do not write to this register)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
NBS
-
ACMUND
HWLNG
-
DT
NLPDC
NB
MSB
LSB
NBS
When high, the Narrowband signal has been detected in the Sin/Sout path and when low, the Narrowband signal has not
been detected in the Sin/Sout path
NB
LOGICAL OR of the status bit NBS + NBR from LSR Register
When high the Double Talk is detected and when low, the Double talk is not detected
When high, the NLP is activated and when low the NLP is not activated
RESERVED.
DT
NLPDC
-
HWLNG
ACMUND
-
When high, Howling is occurring in the loop and when low, no Howling is detected
When high, No active signal in the Rin/Rout path
RESERVED.
Address:
02h Read
Line Echo Canceller Status Register (LSR) (* Do not write to this register)
Power Up
Reset 00h
6
5
4
3
2
1
0
-
-
NLPC
DT
-
-
NB
NBR
LSB
NBR
When high, a narrowband signal has been detected in the Receive (Rin) path. When low no narrowband signal is not
detected in the Rin path
NB
This bit indicates a LOGICAL-OR of Status bits NBR + NBS (from ASR Register)
When high, double-talk is detected and when low double-talk is not detected
When high, NLP is activated and when low NLP is not activated
DT
NLPC
-
-
-
RESERVED.
.
--
Address:
20h R/W
Receive Gain Control Register (RGC)
Power Up
Reset 6Dh
7
6
5
4
3
2
1
0
GO
-
-
G3
G2
-
-
G1
MSB
LSB
G0
G1
G2
G3
-
User Gain Control on the Rin/Rout path (Tolerance of gains: +/- 0.15 dB).
The hexadecimal number represents G3 to G0 value in the table below.
-
RESERVED
-
-
Gain Values for Receive Gain Control Register Bit G3 to G0 (RGC)
0h
1h
2h
3h
-24 dB
-21 dB
-18 dB
-15 dB
4h
5h
6h
7h
-12 dB
-9 dB
-6 dB
-3 dB
8h
9h
Ah
Bh
0 dB
Ch
Dh
Eh
Fh
+12 dB
+ 3 dB
+ 6 dB
+9 dB
+ 15 dB
+ 18 dB
+ 21 dB
25
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
16h Read
Receive (Rin) Peak Detect Register 1 (RIPD1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
RIPD5
RIPD4
RIPD3
RIPD2
RIPD6
RIPD0
LSB
RIPD7
RIPD1
MSB
RIPD0
RIPD1
RIPD2
RIPD3
RIPD4
RIPD5
RIPD6
RIPD7
These peak detector registers allow the user to monitor the receive in signal (Rin) peak level at reference point R1 (see
Figure #1). The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers. The high byte
is in Register 2 and the low byte is in Register 1.
Address:
17h Read
Receive (Rin) Peak Detect Register 2 (RIPD2)
Power Up
Reset 00h
7
6
5
4
3
2
RIPD11
1
0
RIPD13
RIPD12
RIPD14
RIPD10
RIPD8
RIPD15
RIPD9
MSB
LSB
RIPD8
RIPD9
RIPD10
RIPD11
RIPD12
RIPD13
RIPD14
RIPD15
See Above Description
Address:
18h Read
Receive (Rin) ERROR Peak Detect Register 1 (REPD1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
REPD0
REPD4
REPD3
REPD6
REPD5
REPD2
REPD7
REPD1
MSB
LSB
REPD0
REPD1
REPD2
REPD3
REPD4
REPD5
REPD6
REPD7
These peak detector registers allow the user to monitor the error signal peak level at reference point R2 (see Figure #1).
The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers. The high byte is in
Register 2 and the low byte is in Register 1.
26
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
19h Read
Receive (Rin) ERROR Peak Detect Register 2 (REPD2)
Power Up
Reset 00h
7
6
5
4
3
2
REPD
10
1
0
REPD
REPD
REPD
REPD
REPD
REPD
REPD
9
8
12
15
14
13
11
MSB
LSB
REPD8
REPD9
See above description
REPD10
REPD11
REPD12
REPD13
REPD14
REPD15
Address:
3Ah Read
Receive (Rout) Peak Detect Register 1 (ROPD1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
ROPD0
LSB
ROPD4
ROPD6
ROPD5
ROPD7
ROPD3
ROPD2
ROPD1
MSB
ROPD0
ROPD1
ROPD2
ROPD3
ROPD4
ROPD5
ROPD6
ROPD7
These peak detector registers allow the user to monitor the receive out signal (Rout) peak level at reference point R3 (see
Figure #1). The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers. The high byte
is in Register 2 and the low byte is in Register 1.
Address:
3Bh Read
Receive (Rout) Peak Detect Register 2 (ROPD2)
Power Up
Reset 00h
7
6
5
4
3
2
ROPD10
1
0
ROPD11
ROPD9
ROPD8
ROPD12
ROPD15
ROPD14
ROPD13
MSB
LSB
ROPD8
ROPD9
ROPD10
ROPD11
ROPD12
ROPD13
ROPD14
ROPD15
See Above description
27
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
36h Read
Send (Sin) Peak Detect Register 1 (SIPD1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
SIPD5
SIPD4
SIPD3
SIPD2
SIPD6
SIPD0
LSB
SIPD7
SIPD1
MSB
SIPD0
SIPD1
SIPD2
SIPD3
SIPD4
SIPD5
SIPD6
SIPD7
These peak detector registers allow the user to monitor the receive in signal (Sin) peak level at reference point S1 (see
Figure #1). The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers. The high byte
is in Register 2 and the low byte is in Register 1.
Address:
37h Read
Send (Sin) Peak Detect Register 2 (SIPD2)
Power Up
Reset 00h
7
6
5
4
3
2
SIPD11
1
0
SIPD13
SIPD12
SIPD10
SIPD14
SIPD8
SIPD15
SIPD9
MSB
LSB
SIPD8
SIPD9
SIPD10
SIPD11
SIPD12
SIPD13
SIPD14
SIPD15
See above description
Address:
38h Read
Send ERROR Peak Detect Register 1 (SEPD1)
Power Up
Reset 00h
7
6
5
4
3
2
SEPD3
1
0
SEPD5
SEPD4
SEPD6
SEPD2
SEPD0
SEPD7
SEPD1
MSB
LSB
SEPD0
SEPD1
SEPD2
SEPD3
SEPD4
SEPD5
SEPD6
SEPD7
These peak detector registers allow the user to monitor the error signal peak level in the send path at reference point S2
(see Figure #1). The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers. The high
byte is in Register 2 and the low byte is in Register 1.
28
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
39h Read
Send ERROR Peak Detect Register 2 (SEPD2)
Power Up
Reset 00h
7
6
5
4
3
2
SEPD10
1
0
SEPD9
SEPD8
LSB
SEPD12
SEPD15
SEPD14
SEPD13
SEPD11
MSB
SEPD8
SEPD9
SEPD10
SEPD11
SEPD12
SEPD13
SEPD14
SEPD15
See Above description
Address:
1Ah Read
Send (Sout) Peak Detect Register 1 (SOPD1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
SOPD6
SOPD5
SOPD7
SOPD4
SOPD3
SOPD0
LSB
SOPD1
SOPD2
MSB
SOPD0
SOPD1
SOPD2
SOPD3
SOPD4
SOPD5
SOPD6
SOPD7
These peak detector registers allow the user to monitor the Send out signal (Sout) peak level at reference point S3 (see
Figure #1). The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers. The high byte
is in Register 2 and the low byte is in Register 1.
Address:
1Bh Read
Send (Sout) Peak Detect Register 2 (SOPD2)
Power Up
Reset 00h
7
6
5
4
3
2
SOPD10
1
0
SOPD9
SOPD8
SOPD12
SOPD15
SOPD14
SOPD13
SOPD11
MSB
LSB
SOPD8
SOPD9
SOPD10
SOPD11
SOPD12
SOPD13
SOPD14
SOPD15
See Above description
29
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
3Ch R/W
Acoustic Echo Canceller Adaptation Speed Register 1 (A_AS1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
A_AS0
A_AS6
A_AS5
A_AS7
A_AS4
A_AS3
A_AS1
A_AS2
MSB
LSB
A_AS0
A_AS1
A_AS2
A_AS3
A_AS4
A_AS5
A_AS6
A_AS7
This register allows the user to program control the adaptation speed of the Acoustic Echo Canceller. This register value
changes dynamically when the ’ASC-’ bit in the Acoustic Echo Canceller Control Register is low. The ’ASC-’ bit must be 1
when this register is under user control. The valid range is from 0000h to 7FFFh. The high byte is in Register 2 and the low
byte is in Register 1. Smaller values correspond to slower adaptation speed.
Address:
3Dh R/W
Acoustic Echo Canceller Adaptation Speed Register 2 (A_AS2)
Power Up
Reset 10h
7
6
5
4
3
2
A_AS10
1
0
A_AS9
A_AS8
A_AS12
A_AS15
A_AS14
A_AS13
A_AS11
MSB
LSB
A_AS8
A_AS9
A_AS10
A_AS11
A_AS12
A_AS13
A_AS14
A_AS15
See Above description
Address:
1Ch R/W
Line Echo Canceller Adaptation Speed Register 1 (L_AS1)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
L_AS0
L_AS6
L_AS5
L_AS7
L_AS4
L_AS3
L_AS1
L_AS2
MSB
LSB
L_AS0
L_AS1
L_AS2
L_AS3
L_AS4
L_AS5
L_AS6
L_AS7
This register allows the user to program control the adaptation speed of the Line Echo Canceller. This register value
changes dynamically when the ’ASC-’ bit in the Acoustic Echo Canceller Control Register is low. The ’ASC-’ bit must be 1
when this register is under user control. The valid range is from 0000h to 7FFFh. The high byte is in Register 2 and the low
byte is in Register 1. Smaller values correspond to slower adaptation speed.
30
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
1Dh Read
Line Echo Canceller Adaptation Speed Register 2 (L_AS2)
Power Up
Reset 08h
7
6
5
L_AS13
4
3
2
1
0
L_AS9
L_AS8
LSB
L_AS12
L_AS15
L_AS14
L_AS10
L_AS11
MSB
L_AS8
L_AS9
L_AS10
L_AS11
L_AS12
L_AS13
L_AS14
L_AS15
See Above description
Address:
24h R/W
Rout Limiter Register 1 (RL1)
Power Up
Reset 80h
7
6
5
4
3
2
1
0
-
-
-
L0
-
-
-
-
MSB
LSB
-
-
-
RESERVED
-
-
-
-
L0
This bit is used in conjunction with Rout Limiter Register 2. (See description below.)
Address:
25h R/W
Rout Limiter Register 2 (RL2)
Power Up
Reset 3Eh
7
6
5
4
3
2
1
0
L5
L6
L2
L8
L7
L4
L3
L1
MSB
LSB
L1
L2
L3
L4
L5
L6
L7
L8
In conjunction with bit 7 (L0) of the above (RL1) register, this register (RL2) allows the user to program the output Limiter
threshold value in the Rout path.
Default value is (1f40)h which is equal to 3.14 dBmo
Maximum value is (7FC0)h = 15 dBmo
Minimum value is (0040)h = -38 dBmo
31
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
26h R/W
Sout Limiter Register (SL)
Power Up
Reset 3Dh
7
6
5
4
3
2
1
0
-
-
L1
L4
-
L2
L0
L3
MSB
LSB
-
-
RESERVED
-
L0
L1
L2
L3
L4
This register allows the user to program the output Limiter threshold value in the Rout path
Default value is (1f40)h which is equal to 3.14 dBmo
Maximum value is (7F40)h
Address:
03h Read
Firmware Revision Code Register (FRC)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
-
FRC2
-
FRC0
FRC1
-
-
-
MSB
LSB
-
-
-
-
RESERVED
FRC0
FRC1
FRC2
Revision code of the firmware program currently being run (default=rom=00).
Address:
3fh R / W
Bootload RAM Control Register (BRC)
Power Up
Reset 00h
7
6
5
4
3
2
1
0
-
-
-
-
-
BOOT
RAM_ROMb
-
MSB
LSB
C0
C1
C2
C3
RESERVED. Must be set to zero.
RESERVED. Must be set to zero.
BOOT bit. When high, puts device in bootload mode. When low, bootload is disabled.
RAM_ROMb bit. When high, device executes from RAM. When low, device executes from ROM.
RESERVED
-
-
-
32
Zarlink Semiconductor Inc.
MT93L16
Data Sheet
Address:
07h Read
Bootload RAM Signature Register (SIG)
Power Up
Reset FFh
7
6
5
4
3
2
SIG2
1
0
SIG1
SIG0
LSB
SIG4
SIG7
SIG6
SIG5
SIG3
MSB
SIG7
SIG6
SIG5
SIG4
SIG3
SIG2
SIG1
SIG0
This register provides the signature of the bootloaded data to verify error-free delivery into the device.
Note: this register is only accessible if BOOT bit is high (bootload mode enabled) in the above BRC register. While
bootload is disabled, the register value is held constant at its reset seed value of FFh.
33
Zarlink Semiconductor Inc.
Package Code
c Zarlink Semiconductor 2003 All rights reserved.
Previous package codes
ISSUE
ACN
DATE
APPRD.
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL, the Zarlink Semiconductor logo and the Legerity logo and combinations thereof, VoiceEdge, VoicePort, SLAC, ISLIC, ISLAC and VoicePath are
trademarks of Zarlink Semiconductor Inc.
TECHNICAL DOCUMENTATION - NOT FOR RESALE
相关型号：
©2020 ICPDF网 联系我们和版权申明