MF-2500FXE-M12ZB_技术文档

MITSUBISHI (OPTICAL DEVICES)

Mitsubishi Electric Corp.

Datasheet

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

2.5Gbps L-16.1, L-16.2 / LR-1, LR-2 SFP Transceiver with Digital

Diagnostic Monitoring Interface MF-2500FXE Series

1. Description

This transceiver is compliant with Small

Form-factor Pluggable (SFP) MSA, and

optimized for SDH L-16.1, L-16.2 / SONET

LR-1, LR-2 applications.

The optical subassembly consists of 2 parts,

the transmitter with an uncooled DFB laser in

a hermetic coaxial module, the receiver with

an APD preamp in a hermetic coaxial module

and integrated circuits for reshaping received

optical signal.

The built-in serial ID recognition is

incorporated, which allows users to interface

with two wire serial interface that displays

information on manufacturer, part number,

link, distance, and other parameters.

The Digital Diagnostic Monitoring interface is

incorporated, which monitors transceiver

parameters including Temperature, Supply

voltage, Laser bias current, Laser power and

Received optical power.

2. Features

•

Small Form-factor Pluggable (SFP) MSA compliant transceiver with SONET/SDH system Quality

L-16.1/LR-1 (40km) / L-16.2/LR-2 (80km) application

155Mbps to 2.7Gbps Multi-Rate operation capability

LC duplex receptacle

Single +3.3V power supply

Differential data inputs and outputs

Operating case temperature range -5°C to +85°C

Comply with SFF-8472 MSA

Built-in Programmable receiver low pass filter as application select

Incorporating Digital Diagnostic Monitoring Interface with External calibration

(Internal calibration is optional)

•

Serial ID Functionality

APD integrated in the receiver

Slide latch / Bail latch type

RoHS Compliant

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 1 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

3. Block diagram

APD BIAS CIRCUIT

(DC/DC Converter)

Rx Received Po

Monitor Circuit

Signal Detect

Circuit

RX_LOS

APD

RD-

OPT_IN

Limiting Amp

&Low pass Fil.

RD+

TIA

ROSA

Temperature

Monitor Circuit

Control

Circuits

(DDM)

MOD_DEF [2]

MOD_DEF [1]

TX_FAULT

Supply Voltage

Monitor Circuit

LD Bias & Pout

Monitor Circuit

Memory

Fault Detector

TD-

Driver

LD

TD+

OPT_OUT

L

Bias

TX_DISABLE

Monitor

PD

circuit

TOSA

4. Absolute Maximum Ratings

Stress below listed absolute maximum rating may cause permanent damage to the module.

This is a stress only and functional operation of the module at these or any other conditions in excess of

those given in the operational sections of this data sheet.

Exposure to Absolute Maximum Rating for extended periods may affect module reliability.

Parameters

Symbol

Vcc

Tstg

Tc

Ratings

0 to +4.0

-40 to +85

-5 to +85

5 to 85

Unit

V

Supply voltage

C

Storage temperature

Operating case temperature

Relative humidity(non condensation)

°

C

°

-

%

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 2 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

5. Electrical characteristics

All parameters are specified over the operating case temperature.

Measurement conditions are at 2.48832Gbps +/-20ppm, NRZ PN2²³-1 and 50%duty cycle data signal.

The DATA input/output signal interface is AC-coupled internally.

TX_DISABLE input signal level is LVTTL compatible. (With internally pull-up 4.7k to 10kΩ)

TX_FAULT and LOS(Loss Of Signal) output are Open-Collector/drain, and the levels indicated assuming 4.7k

to 10k ohm pull up resistor to Host_Vcc is present.

Parameters

Supply voltage

Power consumption

Symbol

Vcc

Pc

V_IH

V_IL

Min.

3.13

-

2.0

Typ.

3.3

0.8

-

Max.

3.47

1.2

Vcc

0.8

Unit

V

W

V

TX_DISABLE Input voltage

0

-

V

V_OH

V_OL

V_OH

V_OL

V_OH

V_OL

V_IH

V_IL

V_T

R_T

V_O

R_O

2.0

0

2.0

0

-

Vcc

0.5

Vcc

0.5

Vcc

0.4

V

mV_P-P

Ω

mV_P-P

Ω

TX_FAULT Output voltage

RX_LOS Output voltage

Vcc × 0.8

MOD_DEF[2] Output voltage

MOD_DEF[1], [2] Input voltage

0

Vcc

Vcc × 0.3

2400

-

Vcc × 0.7

0

500

-

370

-

Input Amplitude, Differential

Input Impedance, Differential

Output Amplitude, Differential

Output Impedance, Differential

Data Output Rise/Fall Time

(20% to 80%)

Electrical Input Data Return Loss

100MHz < f < 1.2GHz(Differential)

Electrical Input Data Return Loss

1.2GHz < f < 2.7GHz(Differential)

100

-

100

1600

-

Tr/Tf

Rld1

Rld2

-

12

8

-

150

ps

dB

-

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 3 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

6. Optical characteristics

L-16.1 / LR-1

Transmitter

Parameter

Target Distance

Wavelength

Min.

-

1280

Max.

40

1335

Unit

Km

nm

Optical source

SLM

-

Optical power BOL (3.3V, 25degC)

Optical power EOL

Optical power when disable

Spectral width(-20dB)

SMSR

-1

-2

-

30

8.2

+3

-40

1.0

-

dBm

nm

dB

Extinction ratio

-

Optical waveform

SONET/SDH Mask compliant

-

Return Loss at S

Chromatic Dispersion

Path penalty (note 1)

24

-250

-

+250

1

dB

Ps/nm

dB

Jitter Generation(note 2)

-Bandwidth 5KHz to 20MHz

(ITU-T G.958,G.813 compliant)

Jitter Generation(note 2)

-Bandwidth 1MHz to 20MHz

(ITU-T G.958,G.813 compliant)

note 1 : Support 40km of normal single-mode fiber.

note 2 : Jitter Generation

-

0.5

0.1

UIpp

Optical Input Power

=Overload BOL

RxD+

Jitter Analyzer

SFP Rx

SFP Tx

Opt.

ATT

RxD-

TxD-

Opt.

ATT

TxD+

Receiver

Parameter

Min.

Max.

Unit

Wavelength

Sensitivity

(BOL:3.3V, 25degC, BER=1E-10)

Sensitivity (EOL, BER=1E-10)

Overload BOL (3.3V, 25degC)

Overload EOL

RX_LOS Assert Level

RX_LOS De-assert Level

RX_LOS Hysteresis

1280

1335

nm

-

-28

dBm

-

-7

-8

-38

-

-27

-

dBm

dB

-

-28

6.0

1.0

0.3

-

CID Penalty(note 1)

dB

Jitter Tolerance, Transfer

Maximum reflectance of receiver at R

ITU-T G.958 Compliant(with reference CDR)

-27

-

dB

-

note 1 : Penalty between PRBS 2E23-1 and Consecutive Identical Digits according to ITU-T G957

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 4 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

L-16.2 / LR-2

Transmitter

Parameter

Target Distance

Wavelength

Min.

-

1500

Max.

80

1580

Unit

Km

nm

Optical source

SLM

-

Optical power BOL (3.3V, 25degC)

Optical power EOL

Optical power when disable

Spectral width(-20dB)

SMSR

Extinction ratio

-1

-2

-

30

8.2

+3

-40

1.0

-

dBm

nm

dB

-

Optical waveform

SONET/SDH Mask compliant

-

Return Loss at S

Chromatic Dispersion

Path penalty (note 1)

24

-

+1600

2

dB

ps/nm

dB

Jitter Generation(note 2)

-Bandwidth 5KHz to 20MHz

(ITU-T G.958,G.813 compliant)

Jitter Generation(note 2)

-Bandwidth 1MHz to 20MHz

(ITU-T G.958,G.813 compliant)

note 1 : Support 80km of normal single-mode fiber.

note 2 : Jitter Generation

-

0.5

0.1

UIpp

Optical Input Power

=Overload BOL

RxD+

Jitter Analyzer

SFP Rx

SFP Tx

Opt.

ATT

RxD-

TxD-

Opt.

ATT

TxD+

Receiver

Wavelength

Parameter

Min.

1500

Max.

1580

Unit

nm

Sensitivity BOL

-

-29

dBm

(3.3V, 25degC, BER=1E-10)

Sensitivity EOL (BER=1E-10)

Overload BOL (3.3V, 25degC)

Overload

RX_LOS Assert Level

RX_LOS De-assert Level

RX_LOS Hysteresis

-

-7

-8

-39

-

-28

-

dBm

dB

-

-29

6.0

1.0

0.3

-

CID Penalty(note 1)

dB

Jitter Tolerance, Transfer

Maximum reflectance of receiver at R

ITU-T G.958 Compliant(with reference CDR)

-27

-

dB

-

note 1 : Penalty between PRBS 2E23-1 and Consecutive Identical Digits according to ITU-T G957

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 5 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

7. Digital Diagnostic Monitoring Accuracy

The diagnostic monitoring features internal calibration, and is calibrated over operating temperature and

voltage range. The monitor parameters are represented as defined in SFF-8472.

These parameters of the monitoring accuracy are guaranteed, as long as operating conditions of this SFP

transceiver do not exceed ranges defined below.

Digital Diagnostic Monitoring Accuracy

Parameter

Transceiver Temperature^*1

Supply Voltage

TX Bias Current

TX Optical Power

RX Optical Power

Min.

-3

Max.

+3

Unit

°C

%

dB

Range for Accurate Monitoring

-5 to 85°C

3 to 3.6 V

-

-2 to 3 dBm

-29 to -7dBm

-10

+10

-3(-1.5*²) +3(+1.5*²)

-3(-2*²)

+3(+2*²)

*1:Transceiver Temperature is defined as a case temperature.

*2:These spec are optional.

8. Selective Bandwidth filtering function

Receiver bandwidth is selected by the Rate Select pins(7pin and 9pin).

Each bit rates for the selective bandwidth and adaptable protocols are as follows.

No. Rate Select 0 (7pin) Rate Select 1 (9pin)

Bandwidth

Full

1.25Gbps

622Mbps

155Mbps

Adaptable protocols

STM-16/OC-48, OTN-1

Gigabit Ethernet

STM-4/OC-12, ESCON

STM-1/OC-3, FDDI

1

2

3

4

Low

High

Low

High

Low

High

*Optional Bandwidth : 2.125Gbps and 1.062Gbps bandwidth can be selected by the internal setting.

9. Transceiver pin allocation

No.

1

Symbol

TX GND

TX_FAULT

Description

No.

Symbol

Description

Receiver Ground

Transmitter Ground

11 RX GND

12 RD-

2

Transmitter Fault Indication

Receiver Data Output-Bar

Receiver Data Output

Receiver Ground

3

TX_DISABLE Transmitter Disable

13 RD+

4

MOD_DEF[2]

MOD_DEF[1]

MOD_DEF[0]

Rate Select 0

RX_LOS

Module Definition 2

Module Definition 1

Module Definition 0

Rate Select pin 0

Loss of Signal

14 RX GND

15 RX Vcc

16 TX Vcc

17 TX GND

18 TD+

5

Receiver Power Supply

Transmitter Power Supply

Transmitter Ground

6

7

8

Transmitter Data in

9

Rate Select 1

Rate Select pin 1

Receiver Ground

19 TD-

Transmitter Data in-Bar

Transmitter Ground

10 RX GND

20 TX GND

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 6 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

10. Pin Descriptions

Pin No.

Function

I/O

Pin description

1,17,20 TX GND

I

These pins are the Transmitter ground connections.

They should be connected to a low impedance ground plane(0V).

9,10,

11,14

16

RX GND

TX Vcc *

I

These pins are the Receiver ground connections.

They should be connected to a low impedance ground plane(0V).

This is the power supply pin for the Transceiver part.

It should be connected to +3.3V.

Recommended power supply decoupling. (See Figure 8)

15

RX Vcc *

TD+ / TD-

I

This is the power supply pin for the Receiver part.

It should be connected to +3.3V.

Recommended power supply decoupling. (See Figure 8)

* Both TX Vcc and RX Vcc have been internally connected due to supply of

control circuit Vcc.

This data input pin modulates the laser diode. When the TD+ input is asserted, the

laser diode is turned on.

18,19

They are internally AC-coupled into an equivalent load of RI differential, as shown

in Figure 8.

3

TX_DISAB

LE

I

Active high TTL input, with internal 7.4k ohm pull-up resistor to Vcc.

Asserting the transmitter disable will deactivate the laser within the assert time.

Table 1 indicates the timing of TX_DISABLE.

12,13

RD+ / RD-

O

Received Data Out and Inverted Received Data Out are differential serial output

from the receiver.

These are AC-coupled 100 ohm differential lines which should be terminated with

a 100 ohm (differential) at the user SERDES, as shown in Figure 8. AC coupling is

done inside the module and is thus not required on the host board.

Active high open collector/drain output which indicates a loss-of-signal condition

(LOS). When the average optical power received by the module is below the

Assert Level, RX_LOS is indicated.

Table 1 indicates the timing of RX_LOS. RX_LOS requires a 4.7k to 10k ohm

pull-up resistor external to the module, i.e., in the host system Host_Vcc, as shown

in Figure 8.

The pull-up voltage is between 2.0 V and VccR(VccT) + 0.3 V.

Active high open collector/drain output which indicates a fault in the module. This

can be failure of the laser diode. Under this conditions, TX_FAULT will activate

and be latched. And then the laser will be deactivated within the assert time.

TX_FAULT also requires a 4.7k to 10k ohm pull-up resistor externally, i.e. in the

host system Host_Vcc, as shown in Figure 8.

8

2

RX_LOS

O

TX_FAULT

The pull-up voltage is between 2.0 V and VccT(VccR) +0.3V.

It can be reset by toggling TX_DISABLE high for at least t_reset.

See Figure 8 and Figure 5.

6,5,4

MOD_DEF

[0:2]

-

I

This module has a serial ID function which provides information about the

transceiver’s capabilities, standard interfaces, manufacturer and other information.

This function is provided via a two wire serial EEPROM interface.

MOD_DEF[0] is connected to ground inside the module.(LOW)

MOD_DEF[1] is the serial clock signal input.(SCL)

MOD_DEF[2] is the data output/input.(SDA)

The serial ID definitions are as given in the “SFP-MSA” standard. See Figure 9.

These pins defined the bandwidth filters. 7pin/9pin setting=[*/*]:

[0/0]:Full bandwidth, [1/0]:1.25Gbps, [0/1]:622Mbps, [1/1]:155Mbps

These input pins are internally pulled down to GND with 33Kohm resistor.

If this function is not used, both pins should be left open or connected to GND.

7,9

Rate Select

0, 1

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 7 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

Table 1

Timing of control and status I/O

The timing of the control and status line are listed in below and Figure 1 to 7.

Parameter

TX_DISABLE

Assert Time

Symbol

Min

Max

Unit

Condition

Time from rising edge of TX_DISABLE to

when the optical output falls below 10% of

nominal

t_off

-

10

µs

TX_DISABLE

Negate Time

Time from falling edge of TX_DISABLE to

when the modulated optical output rises

above 90% of nominal

From power on or negation of TX_FAULT

using TX_DISABLE

t_on

-

1

ms

Time to Initialize,

Including Reset of

TX_FAULT

Assert Time

TX_DISABLE

to Reset

RX_LOS

Assert Time

RX_LOS

Negate Time

Serial ID

t_init

300

Time from fault to TX_FAULT on

T_fault

T_reset

t_losson

t_lossoff

f_clock

-

10

-

100

-

µs

Time TX_DISABLE must be held high to

reset TX_FAULT

Time from LOS state to RX_LOS Assert

100

µs

Time from non-LOS state to RX_LOS

de-assert

-

µs

-

kHz

-

Clock Rate

Figure 1

Power on initialization of SFP transceiver, TX_DISABLE negated

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 8 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

Figure 2

Power on initialization of SFP transceiver, TX_DISABLE asserted

Figure 3

SFP TX_DISABLE timing during normal operation

Figure 4

Detection of transmitter fault condition

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 9 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

Figure 5

Successful recovery from transient fault condition

Figure 6

Unsuccessful recovery from fault condition

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 10 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

Figure 7

Timing of RX_LOS detection

Figure 8

Example of SFP Host Board Schematic

SFP Module

Host Board

Protocol Vcc

TD+

LASER

100 ohm

DRIVER

TD-

4.7k to 10k

ohm

TX_FAULT

TX_DISABLE

TX GND

7.4k ohm

1 uH

TX Vcc

RX Vcc

0.1 uF

10 uF

1 uH

+3.3V

PROTOCOL

IC

0.1 uF 10 uF

SERDES

IC

0.1 uF 10 uF

RX GND

RD+

PREAMP

&

POSTAMP

100 ohm

RD-

RX_LOS

Rate Select 0

Rate Select 1

4.7k to 10k

ohm

+3.3V

33k ohm

4.7k to 10k

ohm

4.7k to 10k

ohm

MOD_DEF[0]

MOD_DEF[1]

MOD_DEF[2]

PLD/PAL

SERIAL ID

4.7k to 10k

ohm

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 11 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

Figure 9 Serial ID Table [L16.1]

Data

Address

64

Data

[HEX]

00

Name of Field

ASCII

Name of Field

ASCII

Address

[HEX]

03

04

07

00

14

00

03

19

00

28

FF

00

4D

49

54

53

55

42

49

53

48

49

20

45

4C

45

43

20

00

08

00

70

4D

46

2D

32

35

30

46

58

45

2D

4D

33

31

5A

42

0

1

Identifier

Ext. Identifier

Connector

Options

65

1A

2

3

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

BR, max

00

Transceiver

Encoding

BR, min

00

4

Vendor SN

Date code

*

note 2

note 3

58

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

BR, Nominal

Reserved

Length(9um)-km

Length(9um)

Length(50um)

Length(62.5um)

Length(Copper)

Reserved

Vendor name

Reserved

M

I

Date code

T

Date code

S

Date code

U

Date code

B

Date code

I

Date code

S

Date code

Diagnostic Monitoring Type

Enhanced Options

H

I

00

SPACE

94 SFF-8472 Compliance

01

E

95

96

CC_EXT

note 1

note 4

L

Vendor Specific

E

C

97

98

SPACE

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

Vendor OUI

Vendor PN

Vendor rev

Wavelength

Reserved

M

F

-

2

5

0

F

X

E

-

M

3

1

Z

B

05

1E

00

CC_BASE

note 1

note 1 : This code is check sum code.

note 2 : These address shows unique device serial number.

note 3 : These address shows date code.

note 4 : These address are vendor specific area. Read only.

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 12 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

Serial ID Table [L16.2]

Data

[HEX]

03

Data

Address

64

Data

[HEX]

00

Name of Field

ASCII

Name of Field

ASCII

Address

0

Identifier

Ext. Identifier

Connector

Options

1

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

Options

04

07

00

OC

00

03

19

00

50

FF

00

4D

49

54

53

55

42

49

53

48

49

20

45

4C

45

43

20

00

08

00

70

4D

46

2D

32

35

30

46

58

45

2D

4D

33

32

5A

42

1A

2

BR, max

00

3

Transceiver

Encoding

BR, min

00

4

Vendor SN

Date code

note 2

note 3

58

*

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

BR, Nominal

Reserved

Length(9um)-km

Length(9um)

Length(50um)

Length(62.5um)

Length(Copper)

Reserved

Vendor name

Reserved

M

I

T

S

U

B

I

S

H

92 Diagnostic Monitoring Type

93 Enhanced Options

94 SFF-8472 Compliance

I

00

SPACE

01

E

95

96

CC_EXT

note 1

note 4

L

Vendor Specific

E

C

97

98

SPACE

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

Vendor OUI

Vendor PN

Vendor rev

Wavelength

Reserved

M

F

-

2

5

0

F

X

E

-

M

3

2

Z

B

06

0E

00

CC_BASE

note 1

note 1 : This code is check sum code.

note 2 : These address shows unique device serial number.

note 3 : These address shows date code.

note 4 : These address are vendor specific area. Read only.

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 13 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

11. Type Number

MF - 2500FXE – M 3 1 Z B

Operational Temperature Range

B : -5 ~ +85°C

1 : L-16.1

2 : L-16.2

M2 : Slide latch type & External Calibration

M3 : Bail latch type & External Calibration

(M0 : Slide latch type & Internal Calibration)

(M1 : Bail latch type & Internal Calibration)

12. Reliability reference

Telcordia GR-468-CORE

Radiated Emission:IEC61000-6-3

Immunity:IEC61000-4-2,IEC61000-4-3

Flammability:UL94V-0

ESD for PIN Interface:500V by Human body model (with Rd=1500ohm and Cd=100pF)

13. Laser Safety Information

Class 1 Laser Product(IEC60825 and CDRH compliant)

14. Data sheet

Data sheet which is attached the SFP includes the below parameters.

Condition:

T-ambient 25deg.

Nominal Voltage

Data rate 2.48832Gbps

Data pattern PRBS2E23-1

Parameters:

・ Optical Output Power

・ Wavelength

・ Spectral Width

・ Supply Current

・ Receiver Sensitivity

・ Receiver Overload

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 14 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

15. General Outline Drawing

Slide latch type

MF-2500FXE-M21ZB

25FXE-M21ZB

[ unit : mm]

Bail latch type

MF-2500FXE-M31ZB

25FXE-M31ZB

[unit: mm]

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 15 of 16

MITSUBISHI (OPTICAL DEVICES)

MF-2500FXE Series

2.5Gbps SFP TRANSCEIVER MODULE

16. Packing

Ten SFPs are packed up in this packing box.

Presses Plate

SFP

Dust Cap

Packing box

- Capacity : 10pcs. / box

- Packing box and Presses Plate material :

Cardboard with ESD protection coat.

This product is sensitive to electrostatic discharge. Take precautions to prevent ESD; use wrist straps,

grounded work surfaces and recognized anti-static techniques when handling SFP module.

Mitsubishi reserves the right to change the circuitry and specifications without notice at any time.

No liability is assumed as a result of their use or application. No rights under any patent accompany

the sale of any such product(s) or information.

The end of document

UQ9-05-002 Ed:1.0 Date:9.Sep.2005

Page 16 of 16


型号：	MF-2500FXE-M12ZB
厂家：	Mitsubishi Group
描述：	Optoelectronic Device 光电
文件：	总16页 (文件大小：241K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MF-2500FXE-M12ZB [MITSUBISHI]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E