MM3411Z44 [MITSUMI]
200mA LDO;
| 型号： | MM3411Z44 |
| 厂家： | 
MITSUMI ELECTRONICS, CORP. |
| 描述： | 200mA LDO |
| 文件： | 总24页 (文件大小：283K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MITSUMI
200mA LDO MM3411 Series
200mA LDO
Monolithic IC MM3411 Series
Outline
This IC is a 200mA Low dropout regulator IC with Rush current protection circuit.
No load input current is 25µA typ., and it reduce drop voltage for high speed response.
Rush current protection circuit can control rush current.
Features
1. Maximum operating voltage
2. Output current
6.5V
200mA
3. No load input current
4. Input current (OFF)
5. Output voltage range
6. Output voltage accuracy
7. Dropout voltage
25µA typ.
1µA max.
0.8~5.0V
1%
0.40V typ. (IOUT=200mA)
0.1%/V max.
60mV max.(IOUT=1~200mA)
70dB typ. (f=1kHz)
0.47µF
8. Line regulation
9. Load regulation
10. Ripple rejection
11. Output Capacitor
12. ON/OFF control
Package
SC-82ABB
SOT-25A
Applications
1. Mobile phone, Smart phone
2. Digital camera
3. Game equipment
4. Tablet
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Model Name
M
M
3
4
1
1
E
Function Type
CE=H-Active,
with Discharge Function
Voltage Output RANK
A
Z
=A VO (typ.) =0.80V
=Z VO (typ.) =0.85V
08
50
=A V
O
(typ.)
=0.10V step
=Z V
O
(typ.) =0.05V step
=A VO (typ.) =5.00V
Package
SC-82ABB
SOT-25A
Packing Specifications
U
N
R
R HOUSING
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Block Diagram
VDD
VOUT
CE
Bias
Vref
Current
Limit
GND
Pin Assignment
1
2
3
4
CE
1
2
3
4
5
VDD
GND
CE
NC
VOUT
4
1
3
2
5
1
4
3
GND
VOUT
VDD
2
-
SC-82ABB
(TOP VIEW)
SOT 25A
(TOP VIEW)
Note1 : Heat Spreader Bottom with GND.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Pin Description
SC-82ABB
SOT-25A
Pin No. Pin name
Functions
Voltage−supply pin
GND pin
Pin No. Pin name
Functions
1
2
VDD
GND
ON/OFF−Control pin
CE
L
OUTPUT
OFF
ON/OFF−Control pin
CE
L
H
OUTPUT
OFF
H
ON
1
CE
Connect CE pin with VDD pin,
when it is not used.
And it Can not be used at
OPEN, because it don't have
pulldown.
GND pin
Output pin
Voltage−Supply pin
ON
3
CE
Connect CE pin with VDD pin,
when it is not used.
And it Can not be used at
OPEN, because it don't have
pulldown.
2
3
4
GND
VOUT
VDD
4
5
NC
VOUT
No connection
Output pin
(Except where noted otherwise Ta=25°C)
Absolute Maximum Ratings
Item
Symbol
Tstg
TjMAX
VDD
VCE
VOUT
Iomax
Ratings
−55~+150
150
−0.3~+7.0
−0.3~+7.0
−0.3~+7.0
400
Units
°C
°C
V
V
V
Storage Temperature
Junction Temperature
Supply Voltage
CE input Voltage
Output Voltage
Output Current
mA
330(Note2) (SC
350(Note3) (SOT
650(Note4) (SC 82ABB)
700(Note4) (SOT 25A)
-
82ABB)
Power Dissipation 1
Power Dissipation 2
Pd1
Pd2
mW
mW
-25A)
-
-
Note2 : With PC Board of glass epoxy 100 100 1.6mm
Note3 : With PC Board of glass epoxy 60 40 1.6mm
Note4 : JEDEC51-7 standard 114.3 76.2 1.6mm
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
(Except where noted otherwise Ta=25°C)
Recommended Operating Conditions
Item
Symbol
Topr
Vop
Ratings
-40~+85
1.8~6.5
0~200
Units
°C
V
Operating Ambient Temperature
Operating Voltage
Output Current
Iop
mA
(Except where noted otherwise VDD=VOUT(TYP.)+1V, VCE=VDD, Ta=25°C)
Electrical Characteristics 1
Item
Symbol
IDDOff
IDD
Measurement conditions
VCE=0V
Min. Typ. Max. Units
Input Current(OFF)
No-Load Input Current
0.01 1.0
µA
µA
V
IOUT=0mA
25
40
IOUT=10mA (VOUT 2.00V)
IOUT=10mA (VOUT 2.00V)
0.99
0.02
1.01
+0.02
Output Voltage
VOUT
-
V
VOUT (TYP.)+0.5V VDD 6.5V
VOUT 1.10V, IOUT=10mA
Line Regulation
VLINE
0.01 0.10 %/V
VOUT (TYP.)+1.0V VDD 6.5V
VOUT 1.05V, IOUT=10mA
Load Regulation 1
Load Regulation 2
Dropout Voltage
VLOAD1
VLOAD2
Vio
1mA IOUT 150mA
1mA IOUT 200mA
10
20
40
60
mV
mV
V
Please refer to another page
Ripple Rejection (Note5)
RR
f=1kHz, Vripple=0.5V, IOUT=10mA
70
dB
VOUT Temperature Coefficient (Note5)
Output Current Limit
VOUT
/
T
IOUT=10mA,
-
40 Top 85°C
100
ppm/°C
mA
mA
V
lim
I
200 350
short
I
Output Short-Circuit Current (Note5)
CE High Threshold Voltage
CE Low Threshold Voltage
CE High Threshold Current
CE Low Threshold Current
CL Discharge Resistance (Note5)
VOUT=0V
20
VCEH
VCEL
ICEH
1.5
VDD
0.3
V
-
1.0
1.0
+1.0 µA
+1.0 µA
ICEL
-
Rdisc
VCE=0V, VDD=6V
10
Note5 : The parameter is guaranteed by design.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
(Except where noted otherwise VDD=VOUT(TYP.)+1V, VCE=VDD, Ta=25°C)
Item
Electrical Characteristics 2
Output Voltage
Dropout Voltage
VOUT (V)
Model No.
VOUT (V)
Measurement Conditions Min.
Typ.
0.800
0.900
1.000
1.100
1.200
1.300
1.400
1.500
1.600
1.700
1.800
1.900
2.000
2.100
2.200
2.300
2.400
2.500
2.600
2.700
2.800
2.900
3.000
3.100
3.200
3.300
3.400
3.500
3.600
3.700
3.800
3.900
4.000
4.100
4.200
4.300
4.400
4.500
4.600
4.700
4.800
4.900
5.000
Max. Measurement Conditions Min.
Typ.
Max.
MM3411A08
MM3411A09
MM3411A10
MM3411A11
MM3411A12
MM3411A13
MM3411A14
MM3411A15
MM3411A16
MM3411A17
MM3411A18
MM3411A19
MM3411A20
MM3411A21
MM3411A22
MM3411A23
MM3411A24
MM3411A25
MM3411A26
MM3411A27
MM3411A28
MM3411A29
MM3411A30
MM3411A31
MM3411A32
MM3411A33
MM3411A34
MM3411A35
MM3411A36
MM3411A37
MM3411A38
MM3411A39
MM3411A40
MM3411A41
MM3411A42
MM3411A43
MM3411A44
MM3411A45
MM3411A46
MM3411A47
MM3411A48
MM3411A49
MM3411A50
0.780
0.880
0.980
1.080
1.180
1.280
1.380
1.480
1.580
1.680
1.780
1.880
1.980
2.079
2.178
2.277
2.376
2.475
2.574
2.673
2.772
0.820
0.920
1.020
1.120
1.220
1.320
1.420
1.520
1.620
1.720
1.820
1.920
2.020
2.121
2.222
2.323
2.424
2.525
2.626
2.727
2.828
2.929
3.030
3.131
3.232
3.333
3.434
3.535
3.636
3.737
3.838
3.939
4.040
4.141
4.242
4.343
4.444
4.545
4.646
4.747
4.848
4.949
5.050
0.77
0.88
0.69
0.60
0.51
0.79
0.70
0.61
IOUT=150mA
0.8V VOUT 1.9V
(Note6)
0.47
0.57
IOUT=10mA
2.871
2.970
3.069
3.168
3.267
3.366
3.465
3.564
3.663
3.762
3.861
3.960
4.059
4.158
4.257
4.356
4.455
4.554
4.653
4.752
4.851
4.950
0.31
0.41
IOUT=150mA
1.9V VOUT 5.0V
VDD =VOUT (TYP.) -0.2V
0.23
0.33
0.19
0.28
Note6 : Dropout voltage maximum value in the input and it is confirmed that there is no output abnormal
<
voltage impression the 150mA in the model less than VOUT 1.9V.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Item
Output Voltage
VOUT (V)
Dropout Voltage
VOUT (V)
Model No.
Measurement Conditions Min.
Typ.
0.850
0.950
1.050
1.150
1.250
1.350
1.450
1.550
1.650
1.750
1.850
1.950
2.050
2.150
2.250
2.350
2.450
2.550
2.650
2.750
2.850
2.950
3.050
3.150
3.250
3.350
3.450
3.550
3.650
3.750
3.850
3.950
4.050
4.150
4.250
4.350
4.450
4.550
4.650
4.750
4.850
4.950
Max. Measurement Conditions Min.
Typ.
Max.
MM3411Z08
MM3411Z09
MM3411Z10
MM3411Z11
MM3411Z12
MM3411Z13
MM3411Z14
MM3411Z15
MM3411Z16
MM3411Z17
MM3411Z18
MM3411Z19
MM3411Z20
MM3411Z21
MM3411Z22
MM3411Z23
MM3411Z24
MM3411Z25
MM3411Z26
MM3411Z27
MM3411Z28
MM3411Z29
MM3411Z30
MM3411Z31
MM3411Z32
MM3411Z33
MM3411Z34
MM3411Z35
MM3411Z36
MM3411Z37
MM3411Z38
MM3411Z39
MM3411Z40
MM3411Z41
MM3411Z42
MM3411Z43
MM3411Z44
MM3411Z45
MM3411Z46
MM3411Z47
MM3411Z48
MM3411Z49
0.830
0.930
1.030
1.130
1.230
1.330
1.430
1.530
1.630
1.730
1.830
1.930
2.030
2.129
2.228
2.327
2.426
2.525
2.624
2.723
2.822
2.921
3.020
3.119
3.218
3.317
3.416
3.515
3.614
3.713
3.812
3.911
4.010
4.109
4.208
4.307
4.406
4.505
4.604
4.703
4.802
4.901
0.870
0.970
1.070
1.170
0.77
0.88
0.69
0.60
0.51
0.79
0.70
0.61
IOUT=150mA
1.270
1.370
1.470
1.570
1.670
1.770
1.870
1.970
2.071
2.172
2.273
2.374
2.475
2.576
2.677
2.778
2.879
2.980
3.081
3.182
3.283
3.384
3.485
3.586
3.687
3.788
3.889
3.990
4.091
4.192
4.293
4.394
4.495
4.596
4.697
4.798
4.899
5.000
0.8V VOUT 1.9V
(Note6)
0.47
0.57
IOUT=10mA
0.31
0.41
IOUT=150mA
1.9V VOUT 5.0V
VDD =VOUT (TYP.) -0.2V
0.23
0.19
0.33
0.28
Note6 : Dropout voltage maximum value in the input and it is confirmed that there is no output abnormal
<
voltage impression the 150mA in the model less than VOUT 1.9V.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
(Except where noted otherwise VDD=VOUT(TYP.)+1V, VCE=VDD, Ta=25°C)
Item
Electrical Characteristics 3
Output Voltage
Dropout Voltage
VOUT (V)
Model No.
VOUT (V)
Measurement Conditions Min.
Typ.
0.800
0.900
1.000
1.100
1.200
1.300
1.400
1.500
1.600
1.700
1.800
1.900
2.000
2.100
2.200
2.300
2.400
2.500
2.600
2.700
2.800
2.900
3.000
3.100
3.200
3.300
3.400
3.500
3.600
3.700
3.800
3.900
4.000
4.100
4.200
4.300
4.400
4.500
4.600
4.700
4.800
4.900
5.000
Max. Measurement Conditions Min.
Typ.
Max.
MM3411A08
MM3411A09
MM3411A10
MM3411A11
MM3411A12
MM3411A13
MM3411A14
MM3411A15
MM3411A16
MM3411A17
MM3411A18
MM3411A19
MM3411A20
MM3411A21
MM3411A22
MM3411A23
MM3411A24
MM3411A25
MM3411A26
MM3411A27
MM3411A28
MM3411A29
MM3411A30
MM3411A31
MM3411A32
MM3411A33
MM3411A34
MM3411A35
MM3411A36
MM3411A37
MM3411A38
MM3411A39
MM3411A40
MM3411A41
MM3411A42
MM3411A43
MM3411A44
MM3411A45
MM3411A46
MM3411A47
MM3411A48
MM3411A49
MM3411A50
0.780
0.880
0.980
1.080
1.180
1.280
1.380
1.480
1.580
1.680
1.780
1.880
1.980
2.079
2.178
2.277
2.376
2.475
2.574
2.673
2.772
0.820
0.920
1.020
1.120
1.220
1.320
1.420
1.520
1.620
1.720
1.820
1.920
2.020
2.121
2.222
2.323
2.424
2.525
2.626
2.727
2.828
2.929
3.030
3.131
3.232
3.333
3.434
3.535
3.636
3.737
3.838
3.939
4.040
4.141
4.242
4.343
4.444
4.545
4.646
4.747
4.848
4.949
5.050
1.00
1.15
0.90
0.78
0.67
1.04
0.90
0.77
IOUT=200mA
0.8V VOUT 1.9V
(Note7)
0.62
0.72
IOUT=10mA
2.871
2.970
3.069
3.168
3.267
3.366
3.465
3.564
3.663
3.762
3.861
3.960
4.059
4.158
4.257
4.356
4.455
4.554
4.653
4.752
4.851
4.950
0.40
0.50
IOUT=200mA
1.9V VOUT 5.0V
VDD =VOUT (TYP.) -0.2V
0.30
0.40
0.25
0.34
Note7 : Dropout voltage maximum value in the input and it is confirmed that there is no output abnormal
<
voltage impression the 200mA in the model less than VOUT 1.9V.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Item
Output Voltage
VOUT (V)
Dropout Voltage
VOUT (V)
Model No.
Measurement Conditions Min.
Typ.
0.850
0.950
1.050
1.150
1.250
1.350
1.450
1.550
1.650
1.750
1.850
1.950
2.050
2.150
2.250
2.350
2.450
2.550
2.650
2.750
2.850
2.950
3.050
3.150
3.250
3.350
3.450
3.550
3.650
3.750
3.850
3.950
4.050
4.150
4.250
4.350
4.450
4.550
4.650
4.750
4.850
4.950
Max. Measurement Conditions Min.
Typ.
Max.
MM3411Z08
MM3411Z09
MM3411Z10
MM3411Z11
MM3411Z12
MM3411Z13
MM3411Z14
MM3411Z15
MM3411Z16
MM3411Z17
MM3411Z18
MM3411Z19
MM3411Z20
MM3411Z21
MM3411Z22
MM3411Z23
MM3411Z24
MM3411Z25
MM3411Z26
MM3411Z27
MM3411Z28
MM3411Z29
MM3411Z30
MM3411Z31
MM3411Z32
MM3411Z33
MM3411Z34
MM3411Z35
MM3411Z36
MM3411Z37
MM3411Z38
MM3411Z39
MM3411Z40
MM3411Z41
MM3411Z42
MM3411Z43
MM3411Z44
MM3411Z45
MM3411Z46
MM3411Z47
MM3411Z48
MM3411Z49
0.830
0.930
1.030
1.130
1.230
1.330
1.430
1.530
1.630
1.730
1.830
1.930
2.030
2.129
2.228
2.327
2.426
2.525
2.624
2.723
2.822
2.921
3.020
3.119
3.218
3.317
3.416
3.515
3.614
3.713
3.812
3.911
4.010
4.109
4.208
4.307
4.406
4.505
4.604
4.703
4.802
4.901
0.870
0.970
1.070
1.170
1.00
1.15
0.90
0.78
0.67
1.04
0.90
0.77
IOUT=200mA
1.270
1.370
1.470
1.570
1.670
1.770
1.870
1.970
2.071
2.172
2.273
2.374
2.475
2.576
2.677
2.778
2.879
2.980
3.081
3.182
3.283
3.384
3.485
3.586
3.687
3.788
3.889
3.990
4.091
4.192
4.293
4.394
4.495
4.596
4.697
4.798
4.899
5.000
0.8V VOUT 1.9V
(Note7)
0.62
0.72
IOUT=10mA
0.40
0.50
IOUT=200mA
1.9V VOUT 5.0V
VDD =VOUT (TYP.) -0.2V
0.30
0.25
0.40
0.34
Note7 : Dropout voltage maximum value in the input and it is confirmed that there is no output abnormal
<
voltage impression the 200mA in the model less than VOUT 1.9V.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Measuring Circuit
Ceramic
0.47µF
A
VDD
VOUT
A
V
Ceramic
0.47µF
A
CE
GND
Application Circuit
Ceramic
0.47µF
VOUT
VDD
Ceramic
0.47µF
CE
GND
Temperature Characteristics : B
(Reference example of external parts)
· Output capacitor
· Input capacitor
Ceramic capacitor 0.47µF
Ceramic capacitor 0.47µF
· We shall not be liable for any trouble or damage caused by using this circuit.
· In the event a problem which may affect industrial property or any other rights of us or a third party is
encountered during the use of information described in these circuit, we shall not be liable for any such
problem, nor grant a license therefore.
· Note
1. Please use this IC within the stated absolute maximum ratings.
The IC is liable to malfunction should the ratings be exceeded.
2. Due to restrictions on the package power dissipation, the output current value may not be satisfied.
Attention should be paid to the power dissipation of the package when the output current is large or the
voltage between Iinput and Output is high.
3. The output capacitor is required between output and GND to prevent oscillation.
4. The ESR of capacitor must be defined in ESR stability area. It is possible to use a ceramic capacitor without
ESR resistance for output. The ceramic capacitor must be used more than 0.47µF and B temperature
characteristics.
5. The wire of VDD and GND is required to print full ground plane for noise and stability.
6. The input capacitor must be connected a distance of less than 1cm from input pin.
7. It is able to oscillation when you use the capacitor with intense capacitance change such as micro.
Please evaluate IC in the set.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
8. In case the output voltage is above the input voltage, the overcurrent flow by internal parastic diode from
output to input.In such application, the external bypass diode must be connected between output and input
pin.
9. This IC will limit the output current with the overcurrent protection circuit when the overcurrent and the
output do short-circuit.
However, IC generates heat because of the substrate and use conditions and there is a possibility of
destroying it exceeding a permissible loss.
The characteristic changes depending on the substrate condition. Please evaluate IC in the set.
10. In case the output capacitor is over 2.2µF and steady current is under 5mA, it is able to oscillate.
It is recommended that the output capacitor is under 2.2µF on condition that the current is under 5mA.
Please evaluate IC in the set if it is used in the above condition.
Complement : The oscillation is low level noise (200~300µVrms/Vout=3.0V).
So the above condition is recommended only if it is used for a sensitive sensor against noise.
Except for sensitive part against noise, the restriction of above condition is not required.
About Power Dissipation
The Power dissipation change if board to mount IC change because radiative heat fix at board.It is reference
data below, Evaluate IC in the set.
MM3411AxxURE
1. PC Board of glass epoxy
Board size
100mm×100mm t=1.6mm Copper foil area 10%
330mW Ta=25°C
Power dissipation
2. JEDEC51-7 standard
Board size
114.3mm×76.2mm t=1.6mm Copper foil area 80%
Power dissipation
650mW Ta=25°C (It is reference value measured by JEDEC51-7 standard.)
900
800
700
2. JEDEC51-7 standard
600
500
400
300
200
100
0
1. PC Board of glass epoxy
0
25
50
75
100
125
150
Ambient Temperature(˚C)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
MM3411AxxNRE
1. PC Board of glass epoxy
Board size
60mm×40mm t=1.6mm Copper foil area 60%
Power dissipation
350mW Ta=25°C
2. JEDEC51-7 standard
Board size
114.3mm×76.2mm t=1.6mm Copper foil area 80%
Power dissipation
700mW Ta=25°C (It is reference value measured by JEDEC51-7 standard.)
900
800
700
2. JEDEC51-7 standard
600
500
400
300
200
100
0
1. PC Board of glass epoxy
0
25
50
75
100
125
150
Ambient Temperature(˚C)
It is recommended to layout the VIA for heat radiation in the GND pattern of reverse (of IC) when there is the
GND pattern in the inner layer (in using multiplayer substrate).
By increasing these copper foil pattern area of PCB, Power dissipation improves.
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
(Except where noted otherwise VDD=VOUT(TYP.)+1V, VCE=VDD, Ta=25°C)
Characteristics (VOUT=0.8V)
Input Voltage
-
Output Voltage
Input Voltage
- Input Current
RL=
1.5
30
1.0
20
10
0
RL=800
RL=26
RL=8
0.5
0.0
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Input Voltage VDD (V)
Input Voltage VDD (V)
Load Regulation
Line Regulation
RL=80
40
30
6
4
20
2
10
0
0
−10
−20
−30
−40
−2
−4
−6
0
50
100
150
200
1.5
2.5
3.5
4.5
5.5
6.5
Output Current IOUT (mA)
Input Voltage VDD (V)
Vout Temperature Coefficient
0.90
0.85
0.80
0.75
0.70
−50 −25
0
25
50
75
100
Temperature Ta (ºC)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Ripple Rejection
ESR stable area
0
100
IOUT=50mA
IOUT=10mA
Instable area
Stable area
−20
10
1
−40
−60
IOUT=1mA
0.1
0.01
−80
−100
0.01
0.1
1
10
100
1000
0
50
100
150
200
Frequency (kHz)
Output Current IOUT (mA)
Current Limit
1
0.8
0.6
0.4
0.2
0
VDD=2.0V
VDD=1.8V
0
50
100 150 200 250 300
Output Current IOUT (mA)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Load Transient response
(VDD=VOUT+1V, VCE=VDD, Cin=Cout=0.47µF)
IOUT=1mA 50mA
IOUT=1mA 150mA
10µs/div
10µs/div
IOUT:100mA/div
VOUT:100mV/div
IOUT:50mA/div
VOUT:50mV/div
45mV
80mV
IOUT=10mA 100mA
IOUT=50mA 100mA
IOUT:50mA/div
10µs/div
10µs/div
IOUT:50mA/div
VOUT:50mV/div
VOUT:50mV/div
50mV
30mV
CE Transient
(VDD=1.8V, VCE=0V VDD, CO=0.47µF)
CE Transient
(VDD=1.8V, VCE=0V VDD, CO=10µF)
10µs/div
50µs/div
VCE:2V/div
VCE:2V/div
VOUT:0.5V/div
VOUT:0.5V/div
Iin:100mA/div
Iin:100mA/div
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Output Rise Time
(VDD=VOUT+1V, VCE=0V VDD, Cin=0.47µF)
Output Capacitor − Output Rise Time
Output Capacitor − Output Rise Time
(Co=0.47µF − 47µF)
(Co=0.47µF − 1000µF)
10
200
150
100
50
8
6
4
2
0
0
0
200
400
600
800
1000
0
10
20
30
40
50
Output Capacitor Co (µF)
Output Capacitor Co (µF)
Output Capacitor Co − Rush Current
(Co=0.47µF − 1000µF)
Output Capacitor Co − Rush Current
(Co=0.47µF − 47µF)
400
300
200
100
0
400
300
200
100
0
0
200
400
600
800
1000
0
10
20
30
40
50
Output Capacitor Co (µF)
Output Capacitor Co (µF)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
(Except where noted otherwise VDD=VOUT(TYP.)+1V, VCE=VDD, Ta=25°C)
Characteristics (VOUT=3.0V)
Input Voltage
-
Output Voltage
Input Voltage
- Input Current
RL=
3.5
40
35
30
25
20
15
10
5
3.0
RL=3k
2.5
2.0
1.5
1.0
0.5
0.0
RL=100
RL=30
2
0
0
1
3
4
5
6
7
0
1
2
3
4
5
6
7
Input Voltage VDD (V)
Input Voltage VDD (V)
Load Regulation
Line Regulation
RL=300
40
30
10
20
5
0
10
0
−10
−20
−30
−40
−5
−10
0
50
100
150
200
3.5
4
4.5
5
5.5
6
6.5
Output Current IOUT (mA)
Input Voltage VDD (V)
Dropout Voltage
Vout Temperature Coefficient
VDD=2.8V
RL=300
0.4
0.35
0.3
3.15
3.10
3.05
3.00
2.95
2.90
2.85
0.25
0.2
0.15
0.1
0.05
0
0
50
100
150
200
−50 −25
0
25
50
75
100
Output Current IOUT (mA)
Temperature Ta (ºC)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Ripple Rejection
ESR stable area
0
100
Instable area
Stable area
−20
10
1
−40
IOUT=1mA
−60
0.1
0.01
IOUT=50mA
100
−80
IOUT=10mA
−100
0.01
0.1
1
10
1000
0
50
100
150
200
Frequency (kHz)
Output Current IOUT (mA)
Current Limit
3.5
3
VDD=4.0V
2.5
2
VDD=3.8V
VDD=3.5V
1.5
1
0.5
0
0
100
200
300
400
500
Output Current IOUT (mA)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Load Transient response
(VDD=VOUT+1V, VCE=VDD, Cin=Cout=0.47µF)
IOUT=1mA 50mA
IOUT=1mA 150mA
10µs/div
10µs/div
IOUT:100mA/div
VOUT:100mV/div
IOUT:50mA/div
VOUT:50mV/div
80mV
35mV
IOUT=10mA 100mA
IOUT=50mA 100mA
IOUT:50mA/div
10µs/div
10µs/div
IOUT:50mA/div
VOUT:50mV/div
VOUT:50mV/div
45mV
30mV
CE Transient
(VDD=4.0V, VCE=0V VDD, CO=0.47µF)
CE Transient
(VDD=4.0V, VCE=0V VDD, CO=10µF)
10µs/div
100µs/div
VCE:5V/div
VCE:5V/div
VOUT:2V/div
VOUT:2V/div
Iin:100mA/div
Iin:100mA/div
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Output Rise Time
(VDD=VOUT+1V, VCE=0V VDD, Cin=0.47µF)
Output Capacitor − Output Rise Time
Output Capacitor − Output Rise Time
(Co=0.47µF − 47µF)
(Co=0.47µF − 1000µF)
30
1200
1000
800
600
400
200
0
25
20
15
10
5
0
0
200
400
600
800
1000
0
10
20
30
40
50
Output Capacitor Co (µF)
Output Capacitor Co (µF)
Output Capacitor Co − Rush Current
(Co=0.47µF − 1000µF)
Output Capacitor Co − Rush Current
(Co=0.47µF − 47µF)
400
300
200
100
0
400
300
200
100
0
0
200
400
600
800
1000
0
10
20
30
40
50
Output Capacitor Co (µF)
Output Capacitor Co (µF)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
(Except where noted otherwise VDD=VOUT(TYP.)+1V, VCE=VDD, Ta=25°C)
Characteristics (VOUT=5.0V)
Input Voltage
-
Output Voltage
Input Voltage
- Input Current
RL=
6
5
40
35
30
25
20
15
10
5
RL=5k
4
3
RL=166
2
1
0
RL=166
0
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Input Voltage VDD (V)
Input Voltage VDD (V)
Load Regulation
Line Regulation
40
30
10
20
5
0
10
0
−10
−20
−30
−40
−5
−10
0
50
100
150
200
5.5
5.7
5.9
6.1
6.3
6.5
Output Current IOUT (mA)
Input Voltage VDD (V)
Dropout Voltage
Vout Temperature Coefficient
VDD=4.8V
0.3
0.25
0.2
5.15
5.10
5.05
5.00
4.95
4.90
4.85
0.15
0.1
0.05
0
0
50
100
150
200
−50 −25
0
25
50
75
100
Output Current IOUT (mA)
Temperature Ta (ºC)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Ripple Rejection
ESR stable area
0
100
Instable area
Stable area
−20
10
1
IOUT=1mA
−40
−60
IOUT=50mA
0.1
0.01
−80
IOUT=10mA
0.1
−100
0.01
1
10
100
1000
0
50
100
150
200
Frequency (kHz)
Output Current IOUT (mA)
Current Limit
6
5
4
3
2
1
0
V
=5.8V
DD
VDD=6.0V
VDD=5.5V
0
100
200
300
400
500
Output Current IOUT (mA)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Load Transient response
(VDD=VOUT+1V, VCE=VDD, Cin=Cout=0.47µF)
IOUT=1mA 50mA
IOUT=1mA 150mA
10µs/div
10µs/div
IOUT:100mA/div
VOUT:100mV/div
IOUT:50mA/div
VOUT:50mV/div
90mV
40mV
IOUT=10mA 100mA
IOUT=50mA 100mA
IOUT:50mA/div
10µs/div
10µs/div
IOUT:50mA/div
VOUT:50mV/div
VOUT:50mV/div
50mV
30mV
CE Transient
(VDD=6.0V, VCE=0V VDD, CO=0.47µF)
CE Transient
(VDD=6.0V, VCE=0V VDD, CO=10µF)
VCE:5V/div
VCE:5V/div
10µs/div
100µs/div
VOUT:2V/div
VOUT:2V/div
Iin:100mA/div
Iin:100mA/div
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI
200mA LDO MM3411 Series
Output Rise Time
(VDD=VOUT+1V, VCE=0V VDD, Cin=0.47µF)
Output Capacitor − Output Rise Time
Output Capacitor − Output Rise Time
(Co=0.47µF − 47µF)
(Co=0.47µF − 1000µF)
50
2000
1500
1000
500
0
40
30
20
10
0
0
200
400
600
800
1000
0
10
20
30
40
50
Output Capacitor Co (µF)
Output Capacitor Co (µF)
Output Capacitor Co − Rush Current
(Co=0.47µF − 1000µF)
Output Capacitor Co − Rush Current
(Co=0.47µF − 47µF)
400
300
200
100
0
400
300
200
100
0
0
200
400
600
800
1000
0
10
20
30
40
50
Output Capacitor Co (µF)
Output Capacitor Co (µF)
• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明