0479502001 [MOLEX]
2.4/ 5GHz Stand Alone Antenna (34.9mm*9mm); 2.4 / 5GHz的独立式天线( 34.9毫米* 9毫米)型号: | 0479502001 |
厂家: | Molex |
描述: | 2.4/ 5GHz Stand Alone Antenna (34.9mm*9mm) |
文件: | 总6页 (文件大小:109K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PRODUCT SPECIFICATION
TITLE
2.4/ 5GHz Stand Alone Antenna (34.9mm*9mm)
TABLE OF CONTENTS
1.0 SCOPE
2.0 PRODUCT DESCRIPTION
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
4.0 RATINGS
5.0 PERFORMANCE
6.0 TEST GROUPINGS
7.0 PACKING
REVISION: ECR/ECN INFORMATION: TITLE:
SHEET No.
EC No:
DATE:
ABU2012-0075
2012-06-19
2.4/5GHZ Stand Alone
Antenna(34.9mm*9mm)
1 of 6
C
DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23
PS-47950-001
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
PRODUCT SPECIFICATION
2.4/5GHZ Stand Antenna
1.0 SCOPE
This Product Specification covers the mechanical, electrical and environmental performances
requirements and test methods for 2.4/5GHz stand alone antenna.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBER (S)
Product name: 2.4/5 GHZ Stand Alone Antenna 47950-****
2.2 Design and Construction
Antenna shall be of the design, construction and physical dimensions specified on the
applicable sales drawing.
2.3 Materials
a) Flex:
b) Plating:
Refer to respective Molex sales or engineering drawings
Refer to respective Molex sales or engineering drawings
c) Cable Line: Refer to respective Molex sales or engineering drawings
d) Connector: Refer to respective Molex sales or engineering drawings
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
See drawings and other sections of this specification for the relevant reference documents. In
cases where the specification differs from the drawings, the drawings take precedence.
4.0 RATINGS
4.1 RF POWER
2 WATTS
4.2 TEMPERATU
Operating:
Storage :
- 30°C to + 75°C
- 30°C to + 75°C
4.3 HUMIDITY
Storage
Test
:
+15~70% RH
+80~95% RH
:
REVISION: ECR/ECN INFORMATION: TITLE:
SHEET No.
EC No:
DATE:
ABU2012-0075
2012-06-19
2.4/5GHZ Stand Alone
Antenna(34.9mm*9mm)
2 of 6
C
DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23
PS-47950-001
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
PRODUCT SPECIFICATION
5.0 PERFORMANCE
5.1 ELECTRICAL REQUIREMENTS FOR CABLE LENGTH 100mm (47950-0001)
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
Frequency Range
2.3GHz~5.85GHz
2.4GHz~2.5GHz 4.8GHz~6.0GHz
5.1.1
Antenna loads on PC/ABS housing with
100mm; 1.13mm diameter micro coax
cable. Measured by VNA5071C
Return Loss
< -10 dB
5.1.2
Measure antenna on recommended
PC/ABS housing through OTA chamber
Peak Gain
Total Efficiency
Polarization
3.0 dBi
>75%
4.6 dBi
>70%
5.1.3
5.1.4
5.1.5
5.1.6
Measure antenna on recommended
PC/ABS housing through OTA chamber
Measure antenna through the OTA
chamber
Liner
Measure antenna on recommended PCB
through VNA E5071C
Input Impedance
50Ohms
5.2 ELECTRICAL REQUIREMENTS FOR CABLE LENGTH 150mm (47950-1001)
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
2.4GHz~2.5 4.8GHz~5.0 5.0GHZ~5.
Frequency Range
2.3GHz~5.85GHz
5.2.1
GHz
GHz
85GHz
Antenna loads on PC/ABS housing with
100mm; 1.13mm diameter micro coax
cable. Measured by VNA5071C
Return Loss
< -10 dB
< -6 dB
< -10 dB
5.2.2
Measure antenna on recommended
PC/ABS housing through OTA chamber
Peak Gain
Total Efficiency
Polarization
3.0 dBi
>75%
2.7 dBi
>60%
3.7 dBi
>70%
5.2.3
5.2.4
5.2.5
5.2.6
Measure antenna on recommended
PC/ABS housing through OTA chamber
Measure antenna through the OTA
chamber
Liner
Measure antenna on recommended PCB
through VNA E5071C
Input Impedance
50Ohms
REVISION: ECR/ECN INFORMATION: TITLE:
SHEET No.
EC No:
DATE:
ABU2012-0075
2012-06-19
2.4/5GHZ Stand Alone
3 of 6
C
Antenna(34.9mm*9mm)
DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23
PS-47950-001
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
PRODUCT SPECIFICATION
5.3 ELECTRICAL REQUIREMENTS FOR CABLE LENGTH 200mm (47950-2001)
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
Frequency Range
2.3GHz~5.85GHz
2.4GHz~2.5GHz 4.8GHz~6.0GHz
5.3.1
Antenna loads on PC/ABS housing with
100mm; 1.13mm diameter micro coax
cable. Measured by VNA5071C
Return Loss
< -10 dB
5.3.2
Measure antenna on recommended
PC/ABS housing through OTA chamber
Peak Gain
Total Efficiency
Polarization
2.9 dBi
>75%
5.0 dBi
>70%
5.3.3
5.3.4
5.3.5
5.3.6
Measure antenna on recommended
PC/ABS housing through OTA chamber
Measure antenna through the OTA
chamber
Liner
Measure antenna on recommended PCB
through VNA E5071C
Input Impedance
50Ohms
5.4 MECHANICAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
Test machine :Max intelligent load tester
Stick the flex antenna in a PC block, pull
cable in horizontal direction
Pull test
Pull force >4.5N
1
5.5 RELIABILITY REQUIREMENTS
DESCRIPTION
Cross section
TEST CONDITION
REQUIREMENT
ITEM
5.5.1
Cross section on pad soldering area.
Check under microscope
No soldering problem
REVISION: ECR/ECN INFORMATION: TITLE:
SHEET No.
EC No:
DATE:
ABU2012-0075
2012-06-19
2.4/5GHZ Stand Alone
Antenna(34.9mm*9mm)
4 of 6
C
DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23
PS-47950-001
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
PRODUCT SPECIFICATION
5.6 ENVIRONMENTAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
1.Test condition:
The device under test is kept for 12 hours in
an environment with a temperature of 55
degrees and a relating humidity of 95%.
Thereafter for 12 Hours in an environment with
a temperature of 25 degrees and a relative
humidity of 95%. The cycle is repeated until a
total of 6 cycles have been completed.
Hereafter the conditions are stabilized at room
temperature.
1) Parts should meet RF
spec before and after test.
2) No cosmetic problem
Humidity Test
5.6.1
1.Test condition:
The product temperature is decreased from
room temperature to -40 degrees during 2
Hours and kept there for 2 hours. Then
temperature is increased to 85 degree during 2 1) Parts should meet RF
hours and kept for 2 hours. The temperature is spec before and after test.
then again decreased to -40 degrees during a 2) No cosmetic problem
2-hours period. The cycle is repeated until a
total of 6 cycles have been completed.
Temperature
cycling test
5.6.2
Hereafter the conditions are stabilized at room
temperature.
1.Test condition:
The device under test is exposed to a spray of
1) Parts should meet RF
spec before and after test.
a 5% (by volume) resolution of Nacl in water
for 2 hours. Thereafter the device under test is
left for 1 week in room temperature at a
relative humidity of 95%. The cycle is repeated
until a total of 2 cycles have been completed.
Here after the conditions are stabilized at room
temperature.
Salt mist test
5.6.3
2) No visible corrosion.
Discoloration accept.
The meaning of text “No Cosmetic Problem” in the table above is:
a. no soldering problem
b. no adhesion problem of glue
c. no peel off of plating
REVISION: ECR/ECN INFORMATION: TITLE:
SHEET No.
EC No:
DATE:
ABU2012-0075
2012-06-19
2.4/5GHZ Stand Alone
Antenna(34.9mm*9mm)
5 of 6
C
DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23
PS-47950-001
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
PRODUCT SPECIFICATION
6.0 TEST GROUPINGS
Test
Item
Description
Group1 Group2 Group3 Group4
X
Cross section
Humidity Test
5.5.1
5.6.1
X
Temperature
cycling test
X
5.6.2
5.6.3
X
Salt mist test
Sample Quantity
5
5
5
5
7.0 PACKAGING
Refer to the Molex related packaging drawings.
REVISION: ECR/ECN INFORMATION: TITLE:
SHEET No.
EC No:
DATE:
ABU2012-0075
2012-06-19
2.4/5GHZ Stand Alone
Antenna(34.9mm*9mm)
6 of 6
C
DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23
PS-47950-001
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明