0638131400 [MOLEX]
Extractor Tool Instruction Sheet; 提取工具说明书
| 型号： | 0638131400 |
| 厂家： | 
Molex |
| 描述： | Extractor Tool Instruction Sheet |
| 文件： | 总7页 (文件大小：422K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Extraction Tool
Extractor Tool
Instruction Sheet
Order No. 63813-1400
SCOPE:
The 63813-1400 Extraction Tool is used on several different connector series.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are
available on www.molex.com.
This tool is used on the E67 Power Train Connectors with 33467 and 33468 .64MM Terminals.
See Section 1, pages 2 thru 6 of this Instruction Sheet.
Terminal Series Number Terminal Order Number
33467-0001 33467-0004
33467
33467-0002 33467-0005
33467-0003 33467-0006
33468-0001 33468-0004
33468-0002 33468-0005
33468-0003 33468-0006
33468
This tool is use on the SPOX BMI Connectors with 5263 and 45627 Terminals.
See Section 2, page 7 of this Instruction Sheet.
Terminal Series Number
Terminal Order Number
08-70-1039 08-70-1047 39-00-0152
08-70-1040 39-00-0042 39-00-0159
08-70-1045 39-00-0043 39-00-0160
08-70-1046 39-00-0151 39-00-1167
45627-0001 45627-0002 45627-1001
5263
45627
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 1 of 7
Extraction Tool
SECTION 1
E67 Power Train Connector Terminal Servicing
Extractor Tool Instruction Sheet
Order No. 63813-1400
For 33467 and 33468 .64mm Series Terminals MX64
1. Wire Dress Cover Removal
With connector removed from module and interface facing down, gently unlatch wire dress cover latch features.
Latch feature
With wire dress cover latch features unlatched; insert finger into wire dress cover and pull up and away from the wire bundle.
Tie Wrap
At this time the tie wrap should be removed from the wire bundle for easier access to the wire to be serviced.
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 2 of 7
Extraction Tool
3. TPA Servicing
Insert a small (2.0mm maximum) flat blade screwdriver into the TPA
service hole at either end of the connector and gently pry up. The TPA
will stop when it reaches its pre-lock position for terminal servicing. *
Approximate TPA travel will be 3.5mm.
Repeat step 1. On the other end of the TPA until the TPA is sitting in it’s
pre-lock position at both ends of the connector.
4. Terminal Removal
Using the Molex 0.64 mm service tool (part no. 63813-1400), gently insert the tip into the terminal service hole adjacent to the
terminal to be serviced. Be careful not to push the service tool into the terminal opening.
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 3 of 7
Extraction Tool
Once past the terminal opening, push the service tool against the terminal and push until it wedges between the terminal and the lock
finger. Once the terminal lock finger is disengaged, gently pull on the wire to release the terminal. If the terminal resists, the service
tool may not be fully engaged. Give the service tool a further push to ensure that it has disengaged the terminal lock finger.
Service Tool
0.64mm Terminal
Terminal Finger
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 4 of 7
Extraction Tool
1. Terminal Installation
With TPA still in pre-lock position, and wire dress cover removed, orient terminal to grommet cap.
Grip the wire no less than 1.25 inches from the terminal insulation crimp and insert through grommet cap and into connector. If
resistance is encountered, retract the terminal and adjust the angle of attack. Continue inserting the terminal until it stops and locks up
on the lock finger with an audible click.
1.25”
2. TPA Seating (TPA pre-lock to final-lock)
With the terminal fully installed, the TPA can be seated into its final-lock position by applying an even force to both ends until it comes
to a stop. If the TPA resists it may be detecting a partially installed terminal. Pull the TPA back into its pre-lock position, check to see
that your terminal is fully installed and push it further into the cavity if required. Now the TPA can be seated.
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 5 of 7
Extraction Tool
2. Tie Wrap installation
3. Wire Dress Cover installation
Americas Headquarters Far East North Headquarters Far East South Headquarters European Headquarters Corporate Headquarters
Visit our Web site at http://www.molex.com
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 6 of 7
Extraction Tool
SECTION 2
SPOX BMI Connector Terminal Servicing
Extractor Tool Instruction Sheet
Order No. 63813-1400
For 45627-0001,45627-0002 and 5263 Series Terminals
This tool is used for the removal of Wire-to-Board Crimp Terminal, Series No. 45627, and No.5263 SPOX from their housing.
Note: Extracted Terminal is not reusable.
OPERATION:
1. Push the terminal forward in the arrow direction before using the Extractor Tool as shown. Insert the Extractor Tool into the slot on
the bottom or top row of the connector housing as shown until it bottoms.
2. The extractor pin will depress the terminal locking tabs then pull the terminated wire out of the housing as shown. Wiggling the
wire while pulling it out will help.
3. Molex does not offer repair parts for Extraction Tools due to the inexpensive nature of the tool.
CONNECTOR
HOUSING
CONNECTOR
HOUSING
EXTRACTION TOOL
EXTRACTION TOOL
45627 TERMINAL
5263 TERMINAL
45627 TERMINAL
5263 TERMINAL
EXTRACTOR PIN
LOCKING TAB
EXTRACTOR PIN
CONNECTOR HOUSING
LOCKING
TAB
CONNECTOR HOUSING
Doc No. 63813-1400
Revision: J
Released Date: 01-23-03
Revision Date: 06-21-06
UNCONTROLLED COPY
Page 7 of 7
相关型号：
©2020 ICPDF网 联系我们和版权申明