MC10H117P [MOTOROLA]

Dual 2-Wide 2-3-input OR-AND/OR-AND Gate; 双路2宽2-3输入或-AND / OR- AND门


型号：	MC10H117P
厂家：	MOTOROLA
描述：	Dual 2-Wide 2-3-input OR-AND/OR-AND Gate 双路2宽2-3输入或-AND / OR- AND门栅极触发器逻辑集成电路光电二极管输入元件
文件：	总3页 (文件大小：101K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SEMICONDUCTOR TECHNICAL DATA

The MC10H117 dual 2–wide 2–3–input OR–AND/OR–AND–Invert gate is a

general purpose logic element designed for use in data control, such as digital

multiplexing or data distribution. Pin 9 is common to both gates. This MECL 10H

part is a functional/pinout duplication of the standard MECL 10K family part,

with 100% improvement in propagation delay, and no increase in power–supply

current.

L SUFFIX

CERAMIC PACKAGE

CASE 620–10

P SUFFIX

PLASTIC PACKAGE

CASE 648–08

•

Propagation Delay, 1.0 ns Typical

Power Dissipation 100 mW/Gate Typical (same as MECL 10K)

Improved Noise Margin 150 mV (Over Operating Voltage and

Temperature Range)

FN SUFFIX

PLCC

CASE 775–02

•

Voltage Compensated

MECL 10K–Compatible

LOGIC DIAGRAM

MAXIMUM RATINGS

Characteristic

Symbol

Rating

Unit

Vdc

Power Supply (V

= 0)

–8.0 to 0

Input Voltage (V

= 0)

0 to V

Output Current— Continuous

— Surge

out

100

Operating Temperature Range

0 to +75

°C

Storage Temperature Range— Plastic

— Ceramic

–55 to +150

–55 to +165

°C

stg

ELECTRICAL CHARACTERISTICS (V

0°

= –5.2 V ±5%) (See Note)

25°

75°

Characteristic

Symbol Min

Max

Min

Max

Min

Max

Unit

Power Supply Current

—

= PIN 1

= PIN 16

= PIN 8

CC1

CC2

Input Current High

Pins 4, 5, 12, 13

Pins 6, 7, 10, 11

Pin 9

µA

inH

—

465

545

710

—

275

320

415

—

275

320

415

DIP

Input Current Low

High Output Voltage

Low Output Voltage

High Input Voltage

Low Input Voltage

0.5

—

0.5

—

0.3

—

µA

inL

PIN ASSIGNMENT

–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc

–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc

–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc

–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc

CC1

CC2

OUT

AC PARAMETERS

Propagation Delay

Rise Time

0.45

0.5

1.35

1.5

0.45

0.5

1.35

1.6

0.5

1.5

1.7

Fall Time

0.5

1.5

0.5

1.6

NOTE:

Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,

afterthermalequilibriumhasbeenestablished.Thecircuitisinatestsocketormountedonaprintedcircuit

board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through

a 50–ohm resistor to –2.0 volts.

IN, IN

Pin assignment is for Dual–in–Line Package.

For PLCC pin assignment, see the Pin Conversion

Tables on page 6–11 of the Motorola MECL Data

Book (DL122/D).

3/93

Motorola, Inc. 1996

REV 5

2–223

MC10H117

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 775–02

ISSUE C

0.007 (0.180)

L–M

Y BRK

–M–

–N–

0.007 (0.180)

L–M

–L–

0.010 (0.250)

L–M

VIEW D–D

0.007 (0.180)

L–M

0.007 (0.180)

L–M

0.004 (0.100)

–T– SEATING

PLANE

0.007 (0.180)

L–M

VIEW S

0.010 (0.250)

L–M

NOTES:

1. DATUMS –L–, –M–, AND –N– DETERMINED

INCHES

MILLIMETERS

DIM

MIN

MAX

0.395

0.180

0.110

0.019

MIN

9.78

4.20

2.29

0.33

MAX

10.03

4.57

2.79

0.48

WHERE TOP OF LEAD SHOULDER EXITS PLASTIC

BODY AT MOLD PARTING LINE.

0.385

0.165

0.090

0.013

2. DIMENSION G1, TRUE POSITION TO BE

MEASURED AT DATUM –T–, SEATING PLANE.

3. DIMENSIONS R AND U DO NOT INCLUDE MOLD

FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)

PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.

6. THE PACKAGE TOP MAY BE SMALLER THAN THE

PACKAGE BOTTOM BY UP TO 0.012 (0.300).

DIMENSIONS R AND U ARE DETERMINED AT THE

OUTERMOST EXTREMES OF THE PLASTIC BODY

EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,

GATE BURRS AND INTERLEAD FLASH, BUT

INCLUDING ANY MISMATCH BETWEEN THE TOP

AND BOTTOM OF THE PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR

PROTRUSION OR INTRUSION. THE DAMBAR

PROTRUSION(S) SHALL NOT CAUSE THE H

DIMENSION TO BE GREATER THAN 0.037 (0.940).

THE DAMBAR INTRUSION(S) SHALL NOT CAUSE

THE H DIMENSION TO BE SMALLER THAN 0.025

(0.635).

0.050 BSC

1.27 BSC

0.026

0.020

0.025

0.350

0.042

–––

0.032

–––

0.356

0.048

0.056

0.020

0.66

0.51

0.64

8.89

1.07

–––

0.81

–––

9.04

1.21

1.42

0.50

0.310

0.040

0.330

–––

7.88

1.02

8.38

–––

MOTOROLA

2–224

MECL Data

DL122 — Rev 6

MC10H117

OUTLINE DIMENSIONS

L SUFFIX

CERAMIC DIP PACKAGE

CASE 620–10

–A–

NOTES:

ISSUE V

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN

FORMED PARALLEL.

4. DIMENSION F MAY NARROW TO 0.76 (0.030)

WHERE THE LEAD ENTERS THE CERAMIC

BODY.

–B–

INCHES

MILLIMETERS

DIM

MIN

MAX

0.785

0.295

0.200

0.020

MIN

19.05

6.10

–––

MAX

19.93

7.49

5.08

0.50

0.750

0.240

–––

–T–

SEATING

PLANE

0.015

0.39

0.050 BSC

1.27 BSC

0.055

0.065

1.40

1.65

0.100 BSC

2.54 BSC

0.008

0.125

0.015

0.170

0.21

3.18

0.38

4.31

J 16 PL

0.300 BSC

7.62 BSC

0.25 (0.010)

T B

D 16 PL

0.25 (0.010)

0.020

0.040

0.51

1.01

P SUFFIX

PLASTIC DIP PACKAGE

CASE 648–08

ISSUE R

NOTES:

–A–

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN

FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

INCHES

MILLIMETERS

DIM

MIN

MAX

0.770

0.270

0.175

0.021

0.70

MIN

18.80

6.35

3.69

0.39

1.02

MAX

19.55

6.85

4.44

0.53

1.77

0.740

0.250

0.145

0.015

0.040

SEATING

–T–

0.100 BSC

0.050 BSC

2.54 BSC

1.27 BSC

PLANE

0.008

0.015

0.130

0.305

0.21

0.38

3.30

7.74

0.110

0.295

2.80

7.50

D 16 PL

0.25 (0.010)

0.020

0.040

0.51

1.01

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and

specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola

datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”

must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of

others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other

applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury

ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees

arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that

Motorola was negligent regarding the design or manufacture of the part. Motorola and

Opportunity/Affirmative Action Employer.

are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal

How to reach us:

USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;

JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 5405, Denver, Colorado 80217. 1–800–441–2447

3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609

INTERNET: http://Design–NET.com

ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

MC10H117/D

◊

MECL Data

DL122 — Rev 6

2–225

MOTOROLA

相关型号：