MOC3062 [MOTOROLA]
6-Pin DIP Zero-Cross Optoisolators Triac Driver Output; 6引脚DIP零交叉光隔离器可控硅驱动器输出
| 型号： | MOC3062 |
| 厂家： | 
MOTOROLA |
| 描述： | 6-Pin DIP Zero-Cross Optoisolators Triac Driver Output |
| 文件： | 总6页 (文件大小：293K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Order this document
by MOC3061/D
SEMICONDUCTOR TECHNICAL DATA
GlobalOptoisolator
[IFT = 15 mA Max]
[IFT = 10 mA Max]
[IFT = 5 mA Max]
(600 Volts Peak)
*Motorola Preferred Device
The MOC3061, MOC3062 and MOC3063 devices consist of gallium arsenide
infrared emitting diodes optically coupled to monolithic silicon detectors
performing the functions of Zero Voltage Crossing bilateral triac drivers.
They are designed for use with a triac in the interface of logic systems to
equipment powered from 115/240 Vac lines, such as solid–state relays,
industrial controls, motors, solenoids and consumer appliances, etc.
STYLE 6 PLASTIC
•
•
•
•
Simplifies Logic Control of 115/240 Vac Power
Zero Voltage Crossing
6
1
dv/dt of 1500 V/µs Typical, 600 V/µs Guaranteed
STANDARD THRU HOLE
CASE 730A–04
To order devices that are tested and marked per VDE 0884 requirements, the
suffix ”V” must be included at end of part number. VDE 0884 is a test option.
Recommended for 115/240 Vac(rms) Applications:
•
•
•
•
Solenoid/Valve Controls
Lighting Controls
• Temperature Controls
• E.M. Contactors
COUPLER SCHEMATIC
Static Power Switches
AC Motor Drives
• AC Motor Starters
• Solid State Relays
1
2
3
6
5
4
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
ZERO
CROSSING
CIRCUIT
INFRARED EMITTING DIODE
Reverse Voltage
V
R
6
Volts
mA
1. ANODE
2. CATHODE
3. NC
4. MAIN TERMINAL
5. SUBSTRATE
Forward Current — Continuous
I
F
60
Total Power Dissipation @ T = 25°C
Negligible Power in Output Driver
Derate above 25°C
P
D
120
mW
A
1.41
mW/°C
DO NOT CONNECT
6. MAIN TERMINAL
OUTPUT DRIVER
Off–State Output Terminal Voltage
V
600
1
Volts
A
DRM
Peak Repetitive Surge Current
(PW = 100 µs, 120 pps)
I
TSM
Total Power Dissipation @ T = 25°C
Derate above 25°C
P
D
150
1.76
mW
mW/°C
A
TOTAL DEVICE
(1)
Isolation Surge Voltage
(Peak ac Voltage, 60 Hz, 1 Second Duration)
V
ISO
7500
Vac(pk)
Total Power Dissipation @ T = 25°C
Derate above 25°C
P
D
250
2.94
mW
mW/°C
A
Junction Temperature Range
Ambient Operating Temperature Range
T
–40 to +100
–40 to +85
–40 to +150
260
°C
°C
°C
°C
J
(2)
T
A
(2)
Storage Temperature Range
T
stg
Soldering Temperature (10 s)
T
L
1. Isolation surge voltage, V
, is an internal device dielectric breakdown rating.
ISO
1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common.
2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.
Preferred devices are Motorola recommended choices for future use and best overall value.
GlobalOptoisolator is a trademark of Motorola, Inc.
(Replaces MOC3060/D)
Motorola, Inc. 1995
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted)
A
Characteristic
INPUT LED
Symbol
Min
Typ
Max
Unit
Reverse Leakage Current
(V = 6 V)
R
I
—
—
0.05
1.3
100
1.5
µA
R
Forward Voltage
(I = 30 mA)
F
V
Volts
F
OUTPUT DETECTOR (I = 0)
F
Leakage with LED Off, Either Direction
I
—
60
500
—
nA
DRM1
(1)
(Rated V
DRM
)
(3)
Critical Rate of Rise of Off–State Voltage
dv/dt
600
1500
V/µs
COUPLED
LED Trigger Current, Current Required to Latch Output
(2)
I
mA
FT
(Main Terminal Voltage = 3 V
)
MOC3061
MOC3062
MOC3063
—
—
—
—
—
—
15
10
5
Peak On–State Voltage, Either Direction
(I = 100 mA, I = Rated I
V
TM
—
1.8
3
Volts
)
TM FT
F
Holding Current, Either Direction
I
—
—
250
5
—
µA
H
Inhibit Voltage (MT1–MT2 Voltage above which device will not trigger.)
V
20
Volts
INH
(I = Rated I
)
FT
F
Leakage in Inhibited State
I
DRM2
—
—
—
500
—
µA
(I = Rated I , Rated V
, Off State)
F
FT DRM
Isolation Voltage (f = 60 Hz, t = 1 sec)
V
ISO
7500
Vac(pk)
1. Test voltage must be applied within dv/dt rating.
2. All devices are guaranteed to trigger at an I value less than or equal to max I . Therefore, recommended operating I lies between max
F
FT
F
2. I (15 mA for MOC3061, 10 mA for MOC3062, 5 mA for MOC3063) and absolute max I (60 mA).
FT
F
3. This is static dv/dt. See Figure 7 for test circuit. Commutating dv/dt is a function of the load–driving thyristor(s) only.
TYPICAL CHARACTERISTICS
T
A
= 25°C
1.5
1.4
+800
+600
+400
+200
0
OUTPUT PULSE WIDTH – 80
= 30 mA
µs
NORMALIZED TO
1.3
1.2
1.1
1
I
F
T
= 25°C
A
f = 60 Hz
= 25°C
T
A
0.9
–200
–400
–600
–800
0.8
0.7
0.6
0.5
–4
–3
–2
–1
0
1
2
3
4
5
–40
–20
0
20
40
60
C)
80
100
T , AMBIENT TEMPERATURE (
°
V
, ON–STATE VOLTAGE (VOLTS)
A
TM
Figure 1. On–State Characteristics
Figure 2. Inhibit Voltage versus Temperature
2
Motorola Optoelectronics Device Data
500
1.5
1.4
I
= 0
200
100
50
F
1.3
1.2
1.1
I
= RATED I
FT
F
1
0.9
20
10
5
0.8
0.7
0.6
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
C)
100
–40
T , AMBIENT TEMPERATURE (
°
T , AMBIENT TEMPERATURE (°C)
A
A
Figure 3. Leakage with LED Off
versus Temperature
Figure 4. I
, Leakage in Inhibit State
versus Temperature
DRM2
25
20
1.5
1.4
NORMALIZED TO:
PW 100
NORMALIZED TO
= 25
µ
s
in
T
°C
A
1.3
1.2
15
10
1.1
1
0.9
0.8
0.7
5
0
–40
–20
0
20
40
60
C)
80
100
1
2
5
10
20
50
100
T , AMBIENT TEMPERATURE (
°
PW , LED TRIGGER PULSE WIDTH (µs)
A
in
Figure 5. Trigger Current versus Temperature
Figure 6. LED Current Required to Trigger
versus LED Pulse Width
+400
Vdc
R
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
TEST
R = 10 k
Ω
2. 100x scope probes are used, to allow high speeds and
voltages.
C
PULSE
INPUT
3. The worst–case condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
TEST
MERCURY
WETTED
RELAY
X100
SCOPE
PROBE
removingthecurrent.ThevariableR allowsthedv/dttobe
TEST
gradually increased until the D.U.T. continues to trigger in
response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
D.U.T.
the D.U.T. stops triggering.
recorded.
is measured at this point and
RC
V
= 400 V
max
APPLIED VOLTAGE
WAVEFORM
252 V
RC
0.63 V
max
RC
378
RC
dv dt
0 VOLTS
Figure 7. Static dv/dt Test Circuit
Motorola Optoelectronics Device Data
3
Typical circuit for use when hot line switching is required.
In this circuit the “hot” side of the line is switched and the
load connected to the cold or neutral side. The load may be
connected to either the neutral or hot line.
V
R
in
CC
360 Ω
1
6
5
HOT
2
3
MOC3061–63
39
R
is calculated so that I is equal to the rated I of the
in
F
FT
240 Vac
part, 15 mA for the MOC3061, 10 mA for the MOC3062,
and 5 mA for the MOC3063. The 39 ohm resistor and 0.01
µF capacitor are for snubbing of the triac and may or may
not be necessary depending upon the particular triac and
load used.
4
0.01
LOAD
360
NEUTRAL
Figure 8. Hot–Line Switching Application Circuit
240 Vac
D1
R1
Suggested method of firing two, back–to–back SCR’s,
with a Motorola triac driver. Diodes can be 1N4001; resis-
tors, R1 and R2, are optional 330 ohms.
1
2
6
5
V
CC
R
in
SCR
MOC3061–63
SCR
360
Ω
3
4
NOTE: This optoisolator should not be used to drive a load directly.
It is intended to be a trigger device only.
D2
R2
LOAD
Figure 9. Inverse–Parallel SCR Driver Circuit
4
Motorola Optoelectronics Device Data
PACKAGE DIMENSIONS
–A–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
6
4
3
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
–B–
1
INCHES
MILLIMETERS
DIM
A
B
C
D
E
MIN
MAX
0.350
0.260
0.200
0.020
0.070
0.014
MIN
8.13
6.10
2.93
0.41
1.02
0.25
MAX
8.89
6.60
5.08
0.50
1.77
0.36
C
F 4 PL
L
0.320
0.240
0.115
0.016
0.040
0.010
N
F
–T–
SEATING
PLANE
K
G
J
K
L
M
N
0.100 BSC
2.54 BSC
0.008
0.100
0.012
0.150
0.21
2.54
0.30
3.81
J 6 PL
G
0.300 BSC
7.62 BSC
M
M
M
0.13 (0.005)
T
B
A
M
0
15
0
15
E 6 PL
0.015
0.100
0.38
2.54
D 6 PL
M
M
M
0.13 (0.005)
T
A
B
STYLE 6:
PIN 1. ANODE
2. CATHODE
3. NC
4. MAIN TERMINAL
5. SUBSTRATE
6. MAIN TERMINAL
CASE 730A–04
ISSUE G
–A–
6
4
3
NOTES:
–B–
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
1
INCHES
MILLIMETERS
DIM
A
B
C
D
E
MIN
MAX
0.350
0.260
0.200
0.020
0.070
0.014
MIN
8.13
6.10
2.93
0.41
1.02
0.25
MAX
8.89
6.60
5.08
0.50
1.77
0.36
L
F 4 PL
0.320
0.240
0.115
0.016
0.040
0.010
H
C
F
–T–
SEATING
PLANE
G
H
J
K
L
0.100 BSC
2.54 BSC
G
J
0.020
0.008
0.006
0.320 BSC
0.332
0.025
0.012
0.035
0.51
0.20
0.16
8.13 BSC
8.43
0.63
0.30
0.88
K 6 PL
0.13 (0.005)
M
E 6 PL
M
M
M
T
B
A
D 6 PL
S
0.390
9.90
M
M
0.13 (0.005)
T
A
B
*Consult factory for leadform
option availability
CASE 730C–04
ISSUE D
Motorola Optoelectronics Device Data
5
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
–A–
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
6
4
3
–B–
INCHES
MILLIMETERS
1
DIM
A
B
C
D
E
MIN
MAX
0.350
0.260
0.200
0.020
0.070
0.014
MIN
8.13
6.10
2.93
0.41
1.02
0.25
MAX
8.89
6.60
5.08
0.50
1.77
0.36
0.320
0.240
0.115
0.016
0.040
0.010
L
N
F 4 PL
F
C
G
J
K
L
0.100 BSC
2.54 BSC
0.008
0.100
0.400
0.015
0.012
0.150
0.425
0.040
0.21
2.54
0.30
3.81
–T–
SEATING
PLANE
10.16
0.38
10.80
1.02
N
G
J
K
D 6 PL
0.13 (0.005)
E 6 PL
M
M
M
T
A
B
*Consult factory for leadform
option availability
CASE 730D–05
ISSUE D
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representationorguaranteeregarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
andspecifically disclaims any and all liability, includingwithoutlimitationconsequentialorincidentaldamages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintendedor unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MOC3061/D
◊
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明