D224ED [MPD]

Very Low Cost, 2W SIP Dual Isolated Output DC/DC Converters; 非常低的成本， 2W SIP双隔离输出DC / DC转换器


型号：	D224ED
厂家：	MICROPOWER DIRECT, LLC
描述：	Very Low Cost, 2W SIP Dual Isolated Output DC/DC Converters 非常低的成本， 2W SIP双隔离输出DC / DC转换器转换器
文件：	总2页 (文件大小：203K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

D200ED _Series

Very Low Cost, 2W SIP

Dual Isolated Output

DC/DC Converters

Electrical Speciﬁcations

Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice.

Input

Key Features:

Parameter

Conditions

Min.

Typ.

5.0

Max.

5.5

Units

5 VDC Input

4.5

• 2W Output Power

• Miniature SIP Case

• UL Approved (File E245422)

• Dual Isolated Outputs

• 1,000 VDC Isolation

• >3.5 MHour MTBF

• 12 Standard Models

• Industry Standard Pin-Out

• LOWEST COST!!

Input Voltage Range

12 VDC Input 10.8

24 VDC Input 21.6

Internal Capacitor

12.0

24.0

13.2

26.4

VDC

Input Filter

Reverse Polarity Input Current

0.3

Output

Parameter

Conditions

Min.

Typ.

3.0

Max.

Units

Output Voltage Accuracy

Line Regulation

For Vin Change of 1%

Iout = 10% to 100%

See Note 2

1.2

Load Regulation

Ripple (20 MHz)

Noise (20 MHz)

15.0

150

250

mV P - P

See Note 2

150

Output Power Protection

Temperature Coefﬁcient

Output Short Circuit

General

120

0.01

0.02

%/ºC

Momentary (0.5 Sec.)

Parameter

Conditions

Min.

60 Seconds 1,000

1,000

Typ.

Max.

Units

VDC

MΩ

RoHS Compliant

Isolation Voltage, Input/Output

Isolation Voltage, Output/Output

Isolation Resistance

Isolation Capacitance

Switching Frequency

Environmental

Parameter

500 VDC 1,000

100 kHz, 1V

kHz

Conditions

Min.

Typ.

Max.

+85

Units

ºC

Operating Temperature Range

Storage Temperature Range

Cooling

Ambient

-40

-55

+25

+125

ºC

Free Air Convection

RH, Non-condensing

Humidity

MicroPower Direct

292 Page Street

Suite D

Stoughton, MA 02072

USA

Physical

Case Size

0.77 x 0.28 x 0.39 Inches (19.6 x 7.0 x 10.0 mm)

Non-Conductive Black Plastic (UL94-V0)

0.09 Oz (2.8g)

Case Material

Weight

Reliability Speciﬁcations

Parameter

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25ºC, Gnd Benign

3.5

MHours

Absolute Maximum Ratings

Parameter

Conditions

Min.

Max.

9.0

Units

5 VDC Input -0.7

12 VDC Input -0.7

24 VDC Input -0.7

Input Voltage Surge (1 Sec)

18.0

30.0

300

450

VDC

Lead Temperature

1.5 mm From Case For 10 Sec

All Models

ºC

Internal Power Dissipation

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

Model Selection Guide

Input

Output 1

Output 2

Fuse Rating

Slow-Blow

(mA)

Model

Efﬁciency

(%, Typ)

Voltage (VDC)

Number

Current (mA)

Voltage Current

Current Voltage Current

Current

(VDC)

(mA, Max) (mA, Min)

(VDC)

(mA, Max) (mA, Min)

Nominal

Range

Full-Load No-Load

D201ED

D202ED

D203ED

D204ED

D211ED

D212ED

D213ED

D214ED

D221ED

D222ED

D223ED

D224ED

4.5 - 5.5

500

487

481

208

201

196

201

102

101

5.0

9.0

200.0

112.0

83.0

20.0

12.0

9.0

5.0

9.0

200.0

112.0

83.0

20.0

12.0

9.0

1,000

500

4.5 - 5.5

12.0

15.0

5.0

12.0

15.0

5.0

4.5 - 5.5

67.0

7.0

67.0

7.0

10.8 - 13.2

21.6 - 26.4

200.0

112.0

83.0

20.0

12.0

9.0

200.0

112.0

83.0

20.0

12.0

9.0

500

12.0

15.0

5.0

12.0

15.0

5.0

500

67.0

7.0

67.0

7.0

500

200.0

112.0

83.0

20.0

12.0

9.0

200.0

112.0

83.0

20.0

12.0

9.0

250

9.0

250

12.0

15.0

12.0

15.0

250

67.0

7.0

67.0

7.0

250

Notes:

Block Diagram

1. Output load regulation is speciﬁed for a load change of 10% to 100%.

2. When measuring output ripple, it is recommended that an external ceramic

capacitor (approx approx 1 µF to 10 µF) be placed from each output to

common.

3. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

4. These converters are speciﬁed for operation without external components.

However, in some applications the addition of input/ouput capacitors will

enhance stability and reduce output ripple. Recommended capacitor values

are:

Input

Capacitor

Output

Capacitor

Vin

Vout

5 VDC

12 VDC

24 VDC

4.7 µF

2.2 µF

1.0 µF

5 VDC

9 VDC

12 VDC

15 VDC

4.7 µF

2.2 µF

1.0 µF

0.47 µF

For applications requiring very low output noise levels, a simple LC ﬁlter

should be effective.

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Derating Curve

Mechanical Dimensions

Pin Connections

Function

+Vin

-Vin

-Vout 1

+Vout 1

-Vout 2

+Vout 2

Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = 0.01 ( 0.25)

• Pin 1 is marked by a “dot” or indentation on the side of the unit

MicroPower Direct

•

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

相关型号：