DA113ERW [MPD]

Analog Circuit;


型号：	DA113ERW
厂家：	MICROPOWER DIRECT, LLC
描述：	Analog Circuit
文件：	总2页 (文件大小：225K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Series

DA100ERW

Low Cost, Miniature

1W SIP, Wide Input

DC/DC Converters

Electrical Speciﬁcations

Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice.

Input

Key Features:

Parameter

Conditions

Min.

4.5

Typ.

5.0

Max.

9.0

Units

VDC

• 1W Output Power

• 2:1 Input Voltage Range

• 1,500 VDC Isolation

• Short Circuit Protected

• Miniature SIP Case

• Single & Dual Outputs

• 1.0 MH MTBF

5 VDC Input

12 VDC Input

9.0

12.0

24.0

48.0

120

18.0

36.0

72.0

Input Voltage Range

24 VDC Input 18.0

48 VDC Input 36.0

No-Load Power Consumption

Output

Parameter

Conditions

Min.

Typ.

1.0

0.2

0.5

Max.

Units

• Industry Standard Pin-Out

• Low Low Cost!!

Output Voltage Accuracy

Output Voltage Balance

Line Regulation

3.0

Vin = Min to Max

Iout = 10% to 100%

See Note 1

0.5

0.75

1.0

Load Regulation , Single Output

Load Regulation , Dual Output

Ripple & Noise (20 MHz)

Temperature Coefﬁcient

Output Short Circuit

General

mV P - P

%/°C

0.03

Continuous (Autorecovery)

Parameter

Conditions

Min.

60 Seconds 1,500

500 VDC 1,000

100 kHz, 1V

Typ.

Max.

Units

VDC

M

Isolation Voltage

Isolation Resistance

Isolation Capacitance

Switching Frequency

Environmental

Parameter

300

kHz

Conditions

Min.

Typ.

Max.

+85

Units

°C

Operating Temperature Range

Storage Temperature Range

Cooling

Ambient

-40

-50

+25

+125

°C

Free Air Convection

RH, Non-condensing

Humidity

Physical

Case Size

0.866 x 0.374 x 0.472 Inches (22.0 x 12.0 x 9.50 mm)

Non-Conductive Black Plastic (UL94-V0)

0.17 Oz (5.0g)

Case Material

Weight

MicroPower Direct

292 Page Street

Suite D

Stoughton, MA 02072

USA

Reliability Speciﬁcations

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25°C, Gnd Benign

1.0

MHours

Absolute Maximum Ratings

Parameter

Conditions

Min.

Max.

11.0

22.0

40.0

80.0

300

Units

VDC

°C

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

5 VDC Input -0.7

12 VDC Input -0.7

24 VDC Input -0.7

48 VDC Input -0.7

Input Voltage Surge (1 Sec)

Lead Temperature

1.5 mm From Case For 10 Sec

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

www.micropowerdirect.com

Model Selection Guide

www.micropowerdirect.com

Input

Output

Fuse Rating

Model

Capcitive Efﬁciency

Voltage (VDC)

Nominal Range

Current (mA)

Full-Load No-Load

Slow-Blow

(mA)

Voltage Current

Current

(mA, Min)

Number

Load

(µF, Max)

(%, Typ)

(VDC)

(mA, Max)

DA102ERW

DA103ERW

DA104ERW

DA106ERW

DA107ERW

DA108ERW

DA112ERW

DA113ERW

DA114ERW

DA116ERW

DA117ERW

DA118ERW

DA122ERW

DA123ERW

DA124ERW

DA126ERW

DA127ERW

DA128ERW

DA132ERW

DA133ERW

DA134ERW

DA136ERW

DA137ERW

DA138ERW

4.5 - 9.0

277

263

266

277

263

109

104

109

104

5.0

12.0

15.0

5.0

12.0

15.0

5.0

12.0

15.0

5.0

12.0

15.0

5.0

12.0

15.0

5.0

12.0

15.0

5.0

12.0

15.0

5.0

12.0

15.0

200.0

83.0

67.0

100.0

42.0

33.0

200.0

83.0

67.0

100.0

42.0

33.0

200.0

83.0

67.0

100.0

42.0

33.0

200.0

83.0

67.0

100.0

42.0

33.0

20.0

8.0

7.0

10.0

4.0

3.0

20.0

8.0

7.0

10.0

4.0

3.0

20.0

8.0

7.0

10.0

4.0

3.0

20.0

8.0

7.0

10.0

4.0

3.0

680

470

330

220

150

680

470

330

220

150

680

470

330

220

150

680

470

330

220

150

750

400

150

4.5 - 9.0

9.0 - 18.0

18.0 - 36.0

36.0 - 72.0

Notes:

Mechanical Dimensions

1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be placed from

the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units.

2. These units should not be operated with a load under 10% of

full load. Operation at no-load may cause damage to the unit.

Input

Output

3. These converters are speciﬁed for operation without external

components. However, in some applications the addition of

input/output capacitors will enhance stability and reduce output

ripple. Recommended capacitor values are given in the table

at right.

Output ripple on single output units may be further enhanced

by using the CS terminal (single output units operated at 50%

load or below should use this function). A low ESR capacitor is

connected between the CS pin and the -Vout pin (the anode of

the capacitor is connected to the -Vout pin). Recommended

capacitor values are given in the table above. If not used, the

CS pin should be left open.

Vin

Vout

Capacitor

5 VDC 100 µF 5 VDC

12 VDC 100 µF 12 VDC

24 VDC 10 µF 15 VDC

48 VDC 10 µF

47 µF

Output Voltage

12V 15V 24V

CS (µF) 47 - 100

22 - 47

4. Dual output units may be connected to provide a 10V, 24V, or 30 VDC output. To do this, connect the load across the

+Vout and -Vout outputs and ﬂoat the output common.

Min

Max

5. The remote on/off control pin is referenced to the -Vin pin. Input

current to the pin should be between 5 - 10 mA with a maximum of

20 mA. Exceeding 20 mA could cause damage to the unit.

On <0.6 VDC to Open Circuit

Off 2.7 VDC 15.0 VDC

6. It is recommended that a fuse be used on the input of a power supply

for protection. See the Model Selection table above for the correct rating.

Derating Curve

Mechanical Notes:

Pin Connections

• All dimensions are typical

in inches (mm)

Pin Single

Dual

• Tolerance x.xx = 0.01 ( 0.25)

-Vin

+Vin

Remote ON/OFF

+Vout

-Vout Common

CS -Vout

-Vin

+Vin

+Vout

NF = No Function

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

相关型号：