G116EI [MPD]

Low Cost, 1W MiniDIP High Isolation DC/DC Converters; 低成本， 1W MINIDIP高隔离的DC / DC转换器


型号：	G116EI
厂家：	MICROPOWER DIRECT, LLC
描述：	Low Cost, 1W MiniDIP High Isolation DC/DC Converters 低成本， 1W MINIDIP高隔离的DC / DC转换器转换器
文件：	总2页 (文件大小：175K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

G100EI _Series

Low Cost, 1W MiniDIP

High Isolation

DC/DC Converters

Electrical Speciﬁcations

Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice.

Input

Parameter

Key Features:

Conditions

Min.

Typ.

5.0

Max.

5.5

Units

• 1W Output Power

• Compact “MiniDIP” Case

• 3,000 VDC Isolation

• UL Approved (File E245422)

• Single & Dual Outputs

• >3.5 MHour MTBF

• 24 Standard Models

• LOWEST COST!!

5 VDC Input

4.5

Input Voltage Range

12 VDC Input 10.8

24 VDC Input 21.6

Internal Capacitor

12.0

24.0

13.2

26.4

VDC

Input Filter

Reverse Polarity Input Current

0.3

Output

Parameter

Conditions

Min.

Typ.

1.0

0.1

1.2

Max.

3.0

Units

Output Voltage Accuracy

Output Voltage Balance

Line Regulation

Dual Output , Balanced Loads

For Vin Change of 1%

1.0

Load Regulation (Note 1)

Ripple & Noise (20 MHz) (Note 2)

Output Power Protection

Temperature Coefﬁcient

Output Short Circuit

General

See Model Selection Guide

mV P - P

120

0.02

0.03

%/ºC

Momentary (1.0 Sec.)

RoHS Compliant

Parameter

Conditions

Min.

60 Seconds 3,000

500 VDC 1,000

100 kHz, 1V

Typ.

Max.

Units

VDC

MΩ

Isolation Voltage

Isolation Resistance

Isolation Capacitance

Switching Frequency

Environmental

Parameter

150

kHz

Min.

Typ.

Max.

+85

Units

ºC

Operating Temperature Range

Storage Temperature Range

Cooling

Ambient

-40

-55

+25

+125

ºC

Free Air Convection

RH, Non-condensing

Humidity

Physical

Case Size

0.80 x 0.40 x 0.25 Inches (20.4 x 10.2 x 6.5 mm)

Non-Conductive Black Plastic (UL94-V0)

0.07 Oz (2.1g)

MicroPower Direct

292 Page Street

Suite D

Case Material

Weight

Stoughton, MA 02072

USA

Reliability Speciﬁcations

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25ºC, Gnd Benign

3.5

MHours

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

Safety Standards

Safety Approvals

Absolute Maximum Ratings

Parameter

UL 1950, EN 60950, IEC 60950

UL, cUL; File No. E245422

Conditions

Min.

Typ.

Max.

9.0

Units

5 VDC Input -0.7

Input Voltage Surge (1 Sec)

12 VDC Input -0.7

24 VDC Input -0.7

18.0

30.0

300

450

VDC

Lead Temperature

1.5 mm From Case For 10 Sec

All Models

ºC

Internal Power Dissipation

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

Model Selection Guide

Input

Output

Voltage Current

(VDC) (mA, Max) (mA, Min)

Load

Regulation

(%, Max)

Fuse Rating

Slow-Blow

(mA)

Model

Efﬁciency

(%, Typ)

Voltage (VDC)

Number

Current (mA)

Full-Load No-Load

Current

Nominal

Range

G101EI

G102EI

G103EI

G104EI

G105EI

G106EI

G107EI

G108EI

G111EI

G112EI

G113EI

G114EI

G115EI

G116EI

G117EI

G118EI

G121EI

G122EI

G123EI

G124EI

G125EI

G126EI

G127EI

G128EI

4.5 - 5.5

10.8 - 13.2

21.6 - 26.4

286

267

256

250

278

267

256

253

115

110

105

103

113

110

105

104

5.0

9.0

12.0

15.0

5.0

200.0

111.0

83.0

67.0

100.0

56.0

42.0

33.0

200.0

111.0

83.0

67.0

100.0

56.0

42.0

33.0

200.0

111.0

83.0

67.0

100.0

56.0

20.0

12.0

9.0

7.0

10.0

6.0

5.0

4.0

20.0

12.0

9.0

7.0

10.0

6.0

5.0

4.0

20.0

12.0

9.0

7.0

10.0

6.0

500

200

100

9.0

12.0

15.0

5.0

9.0

12.0

15.0

5.0

9.0

12.0

15.0

5.0

9.0

12.0

15.0

5.0

9.0

12.0

15.0

42.0

33.0

5.0

4.0

Derating Curve

Other input/output combinations are available

(i.e 3.3 VDC). Contact the factory for details at:

sales@micropowerdirect.com

Notes:

1. Output load regulation is speciﬁed for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

3. These converters will operate without external components. However,

when measuring output ripple, it is recommended that an external ceramic

capacitor be placed

Output Capacitor

Single Dual

5 VDC 10.0 μF 4.7 μF

Input

Capacitor

from the +Vout pin to

the -Vout pin for single

output units and from

each output to common

for dual output units.

An input capacitor will

enhance stability over

Vin

Vout

5 VDC

12 VDC

24 VDC

4.7 μF

2.2 μF

1.0 μF

9 VDC

4.7 μF

2.2 μF

1.0 μF

12 VDC 2.2 μF

15 VDC 1.0 μF 0.47 μF

Mechanical Dimensions

temperature and input line variations. Recommended capacitor values are

given in the table above. For applications requiring very low output noise

levels, a simple LC ﬁlter should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC

output. To do this, connect the load across the positive (+Vout) and negative

(-Vout) outputs and ﬂoat the output common

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Pin Connections

Pin Single Dual

Single

Dual

-Vin

+Vout +Vout

-Vin

No Pin Common

-Vout

+Vin

-Vout

+Vin

NC= No Connection

Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = 0.01 ( 0.25)

• Pin 1 is marked by a “dot” or indentation on the side of the unit

MicroPower Direct

•

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

相关型号：