G117E [MPD]

Low Cost, 1W MiniDIP Single & Dual Output DC/DC Converters; 低成本， 1W MINIDIP单，双输出DC / DC转换器


型号：	G117E
厂家：	MICROPOWER DIRECT, LLC
描述：	Low Cost, 1W MiniDIP Single & Dual Output DC/DC Converters 低成本， 1W MINIDIP单，双输出DC / DC转换器转换器
文件：	总2页 (文件大小：178K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

G100E_Series

Low Cost, 1W MiniDIP

Single & Dual Output

DC/DC Converters

Electrical Speciﬁcations

Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice.

Input

Parameter

Key Features:

Conditions

Min.

Typ.

5.0

Max.

5.5

Units

• 1W Output Power

• Compact “MiniDIP” Case

• UL Approved (File E245422)

• Single & Dual Outputs

• 1,000 VDC Isolation

• >3.5 MHour MTBF

• 24 Standard Models

• LOWEST COST!!

5 VDC Input

4.5

Input Voltage Range

12 VDC Input 10.8

24 VDC Input 21.6

Internal Capacitor

12.0

24.0

13.2

26.4

VDC

Input Filter

Reverse Polarity Input Current

0.3

Output

Parameter

Conditions

Min.

Typ.

1.0

0.1

1.2

Max.

3.0

Units

Output Voltage Accuracy

Output Voltage Balance

Line Regulation

Dual Output , Balanced Loads

For Vin Change of 1%

1.0

Load Regulation (Note 1)

Ripple & Noise (20 MHz) (Note 2)

Output Power Protection

Temperature Coefﬁcient

Output Short Circuit

General

See Model Selection Guide

mV P - P

120

0.02

0.03

%/ºC

Momentary (1.0 Sec.)

RoHS Compliant

Parameter

Conditions

Min.

60 Seconds 1,000

500 VDC 1,000

100 kHz, 1V

Typ.

Max.

Units

VDC

MΩ

Isolation Voltage

Isolation Resistance

Isolation Capacitance

Switching Frequency

Environmental

Parameter

100

kHz

Min.

Typ.

Max.

+85

Units

ºC

Operating Temperature Range

Storage Temperature Range

Cooling

Ambient

-40

-55

+25

+125

ºC

Free Air Convection

RH, Non-condensing

Humidity

Physical

Case Size

0.80 x 0.40 x 0.25 Inches (20.4 x 10.2 x 6.5 mm)

Non-Conductive Black Plastic (UL94-V0)

0.07 Oz (2.1g)

MicroPower Direct

292 Page Street

Suite D

Case Material

Weight

Stoughton, MA 02072

USA

Reliability Speciﬁcations

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25ºC, Gnd Benign

3.5

MHours

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

Safety Standards

Safety Approvals

Absolute Maximum Ratings

Parameter

UL 1950, EN 60950, IEC 60950

UL, cUL; File No. E245422

Conditions

Min.

Typ.

Max.

9.0

Units

5 VDC Input -0.7

Input Voltage Surge (1 Sec)

12 VDC Input -0.7

24 VDC Input -0.7

18.0

30.0

300

450

VDC

Lead Temperature

1.5 mm From Case For 10 Sec

All Models

ºC

Internal Power Dissipation

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

Model Selection Guide

Input

Output

Voltage Current

(VDC) (mA, Max) (mA, Min)

Load

Regulation

(%, Max)

Fuse Rating

Slow-Blow

(mA)

Model

Efﬁciency

(%, Typ)

Voltage (VDC)

Number

Current (mA)

Full-Load No-Load

Current

Nominal

Range

G101E

G102E

G103E

G104E

G105E

G106E

G107E

G108E

G111E

G112E

G113E

G114E

G115E

G116E

G117E

G118E

G121E

G122E

G123E

G124E

G125E

G126E

G127E

G128E

4.5 - 5.5

10.8 - 13.2

21.6 - 26.4

278

270

260

253

278

267

256

253

114

111

105

104

113

110

105

104

5.0

9.0

12.0

15.0

5.0

200.0

111.0

83.0

67.0

100.0

56.0

42.0

33.0

200.0

111.0

83.0

67.0

100.0

56.0

42.0

33.0

200.0

111.0

83.0

67.0

100.0

56.0

20.0

12.0

9.0

7.0

10.0

6.0

5.0

4.0

20.0

12.0

9.0

7.0

10.0

6.0

5.0

4.0

20.0

12.0

9.0

7.0

10.0

6.0

500

200

100

9.0

12.0

15.0

5.0

9.0

12.0

15.0

5.0

9.0

12.0

15.0

5.0

9.0

12.0

15.0

5.0

9.0

12.0

15.0

42.0

33.0

5.0

4.0

Derating Curve

Other input/output combinations are available

(i.e. 3.3 VDC). Contact the factory for details at:

sales@micropowerdirect.com

Notes:

1. Output load regulation is speciﬁed for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

3. These converters will operate without external components. However, when

measuring output ripple, it is recommended that an external ceramic capaci-

tor be placed from the

Output Capacitor

Single Dual

5 VDC 10.0 μF 4.7 μF

Input

Capacitor

+Vout pin to the -Vout

pin for single output

units and from each out-

put to common for dual

output units. An input

capacitor will enhance

stability over tempera-

Vin

Vout

5 VDC

12 VDC

24 VDC

4.7 μF

2.2 μF

1.0 μF

9 VDC

4.7 μF

2.2 μF

1.0 μF

12 VDC 2.2 μF

15 VDC 1.0 μF 0.47 μF

Mechanical Dimensions

ture and input line variations. Recommended capacitor values are given in

the table above. For applications requiring very low output noise levels, a

simple LC ﬁlter should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC

output. To do this, connect the load across the positive (+Vout) and negative

(-Vout) outputs and ﬂoat the output common

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Pin Connections

Pin Single

Dual

Single

Dual

-Vin

+Vout

-Vout

+Vin

+Vout

-Vout

+Vin

No Pin Common

NC = No Connection

Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = 0.01 ( 0.25)

• Pin 1 is marked by a “dot” or indentation on the top of the unit

MicroPower Direct

•

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

相关型号：