MA848D-05RU [MPD]
4:1 Input Range, 8W Single & Dual Output DC/DC Con vert ers;型号: | MA848D-05RU |
厂家: | MICROPOWER DIRECT, LLC |
描述: | 4:1 Input Range, 8W Single & Dual Output DC/DC Con vert ers |
文件: | 总3页 (文件大小:361K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MA800RUSeries
4:1 Input Range, 8W
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min.
9.0
Typ.
24.0
48.0
20
Max.
36.0
72.0
Units
VDC
Key Features:
24 VDC Input
Input Voltage Range
• 8W Output Power
48 VDC Input 18.0
Nominal VIN & Constant Resistive Load
(Pi) Filter
Start Up Time
Input Filter
Input Reflected Ripple Current
Output
Parameter
mS
• 4:1 Input Voltage Range
• EN 60950 Approved
• Compact DIP Case
• 1,600 VDC I/O Isolation
• Meets EN 55032 “A”
• Single & Dual Outputs
• Remote On/Off Control
20.0
mA P - P
Conditions
VIN = Min to Max
Min.
Typ.
1.2
Max.
Units
%
%
Output Voltage Accuracy
Line Regulation
0.2
0.5
1.0
Single Output
Dual Output
See Note 3
See Note 4
Load Regulation, See Note 2
%
• Wide Temperature Operation Cross Regulation, Dual Output
5.0
%
mV P - P
µSec
%
% IOUT
%/ºC
Ripple & Noise (20 MHz)
75
• Industry Standard Pin-Out
Transient Recovery Time, See Note 5
Transient Response Deviation
Output Power Protection
Temperature Coefficient
Output Short Circuit Protection
General
250
25% Load Step Change
3.0
150
0.02
Continuous (Autorecovery)
Parameter
Conditions Min. Typ.
Max.
Units
Input/Output, 60 Seconds 1,600
Case/Input, Output, 60 Seconds 1,600
500 VDC 1,000
Isolation Voltage
VDC
Isolation Resistance
Isolation Capacitance
Switching Frequency
Remote On/Off (See Page 2)
Parameter
Supply On
Supply Off
Standby Input Current
Control Common
Environmental
M⍀
pF
kHz
100 kHz/1V
1,500
270
Conditions
See Note On Page 3
Min.
3.0
0.0
Typ.
Max.
12
1.2
Units
VDC
VDC
mA
5.0
Referenced to -Input (Pins 2, 3)
Parameter
Conditions
Min.
-40
Typ.
Max.
+85
+105
+125
Units
ºC
ºC
Ambient
Case
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
-40
ºC
Free Air Convection
RH, Non-condensing
95
%
Physical
Case Size
Case Material
Weight
Reliability Specifications
Parameter
MicroPower Direct
See Mechanical Diagram (Page 3)
Copper With Nickel Coating (UL94V-0)
0.63 Oz (18g)
292 Page Street
Suite D
Stoughton, MA 02072
USA
Conditions
Min.
Typ.
Max.
Units
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign
1.0
MHours
Safety Standards
Absolute Maximum Ratings
Parameter
UL 60950, EN 62368, EN 60950
Conditions
24 VDC Input
48 VDC Input
1.5 mm From Case For 10 Sec
Min.
Typ.
Max.
50.0
100.0
260
Units
VDC
ºC
Input Voltage Surge (1 Sec)
Lead Temperature
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Model Selection Guide
www.micropowerdirect.com
Input
Output
Over
Max
Fuse Rating
Slow-Blow
(mA)
Model
Voltage Capacitive Efficiency
Voltage (VDC)
Number
Current (mA)
Full-Load No-Load
Voltage Current
Current Protection
(VDC)
Load
(µF Max)
(%, Typ)
(VDC)
(mA, Max) (mA, Min)
Nominal
Range
MA824S-03RU
MA824S-05RU
MA824S-12RU
MA824S-15RU
MA824D-05RU
MA824D-12RU
MA824D-15RU
MA848S-03RU
MA848S-05RU
MA848S-12RU
MA848S-15RU
MA848D-05RU
MA848D-12RU
MA848D-15RU
24
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
345
380
385
385
400
390
385
170
185
190
190
200
190
190
10
10
15
15
10
15
15
10
10
10
10
10
10
10
3.3
5.0
2,000
1,500
665
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
3.9
6.2
1,330
1,330
288
200
900
133
90
80
83
87
87
86
86
87
80
84
87
87
84
87
87
2,000
2,000
2,000
2,000
2,000
2,000
2,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
24
24
12.0
15.0
5.0
15.0
18.0
15.0
15.0
18.0
3.9
24
535
24
800
24
12.0
15.0
3.3
335
24
265
48
2,000
1,500
665
1,330
1,330
288
200
900
133
90
48
5.0
6.2
48
12.0
15.0
5.0
15.0
18.0
15.0
15.0
18.0
48
535
48
800
48
12.0
15.0
335
48
265
Notes:
Temperature Derating Curve
1. The specified maximum capacitive load is for each output.
2. Load regulation is specified for a load change of 0% to 100%. Load regulation for 3.3V
output models is 1.0% max for a load change of 0% to 100%.
3. When measuring cross regulation, the load on one output is varied from 25% to 100%
while the other output is held at 100%.
4. Output ripple is measured with a 1.0 µF capacitor connected from the +VOUT to the -VOUT pins
for single output units and from each output to common for dual output models. See the typical
connection diagram & notes on page 3.
5. Transient recovery is measured to within a 1% error band for a load step change of 75% to 50%
to 25%.
6. Operation at no-load will not damage these units. However, they may not meet all
specifications.
7. It is recommended that a fuse be used on the input of a power supply for protection.
See the table above for the correct rating.
Typical Connection
To help meet conducted emissions requirements, the filter components (C2, C3 & L1) in the
diagram above should be used.The recommended values are 2.2 µF/100V for C2 & C3 and
12 µH for L1. These components should be mounted as close to the module as possible.
To meet the requirements of EN 61000-4-4 & EN 61000-4-5, an external filter capacitor
(C1 in the diagram above) is required. The recommended value for C1 is 330 µF/100V.
EMI Characteristics
Parameter
Radiated Emissions
Conducted Emissions
ESD
RS
EFT
Surge
CS
Standard
EN 55032
Criteria/Level
Class A
Class A
EN 55032
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
A
A
A
A
A
A
When measuring output ripple, it is recommended that an external 1.0 µF ceramic capaci-
tor be placed from the +VOUT pin to the -VOUT pin for single output units and from each
output to common for dual output units. For noise sensitive applications, the use of 3.3 µF
capacitors will reduce the output ripple.
The Remote On/Off circuit is referenced to the minus input of the unit (pins 2 & 3). If the
On/Off input (pin 1) is connected to the minus input, the unit is shut off. If pin 1 is left
open, the unit operates normally.
PFM
Page 2
We Power Your Success - For Less
www.micropowerdirect.com
Efficiency vs Output Load: 24 VIN Models
Efficiency vs Output Load: 48 VIN Models
Mechanical Dimensions
Pin Connections
Pin
1
Single
Dual
Remote On/Off Remote On/Off
2
3
-VIN
-VIN
-VIN
-VIN
9
No Pin
NC
+VOUT
-VOUT
+VIN
Common
-VOUT
+VOUT
Common
+VIN
11
14
16
22
23
+VIN
+VIN
NC: No Connection
Mechanical Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = 0.02 ( 0.50)
MPD offers a wide range of DC/DC converters in the
standard 24 pin DIP package. Models range from 1W to
15W and offer wide input ranges, high isolation & tight
regulation. Many are approved to EN 60950. For full in-
formation, go to our website or contact the factory.
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号:
©2020 ICPDF网 联系我们和版权申明