MB2024SMRW-15RI4 [MPD]
Medical Approved, 20W Compact 1 x 2 Inch DC/DC Con vert ers;
| 型号： | MB2024SMRW-15RI4 |
| 厂家： | 
MICROPOWER DIRECT, LLC |
| 描述： | Medical Approved, 20W Compact 1 x 2 Inch DC/DC Con vert ers |
| 文件： | 总4页 (文件大小：471K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MB2000MRWRI4
Medical Approved, 20W
Compact 1 x 2 Inch
DC/DC Converters
Electrical Specifications
Key Features:
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
• EN 60601 3RD Ed. Approved
• 20W Output Power
• 4.2 kVrms Isolation
• Reinforced Insulation
• 2 x MOPP per EN 60601-1
3RD Edition & ANSI/AAMI
ES 60601-1
Input
Parameter
Conditions
12 VDC Input
Min.
Typ.
Max.
9.0
Units
Input Start Voltage
24 VDC Input
48 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
18.0
36.0
VDC
7.5
15.0
33.0
Under Voltage Shutdown
VDC
mS
Input Filter
Start Up Time
(Pi) Filter
Nominal VIN, Constant, Resistive Load
30
• 5 µA Max Leakage Current
• Wide 2:1 Input Range
• Compact 1 x 2 In Case
• Single & Dual Outputs
• 1.08 MH MTBF
Output
Parameter
Conditions
Min.
Typ.
Max.
1.0
2.0
0.5
0.5
Units
%
%
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Dual Output , Balanced Loads
VIN = Min to Max
Single Output
%
Load Regulation, IOUT = 0% to 100%
%
Dual Output
1.0
5V Output
50
Ripple & Noise (20 MHz), See Note 2
12V, 15V, 12V, 15V Output
24V Output
100
150
150
mV P - P
Output Power Protection
Transient Recovery Time, See Note 3
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
General
Hiccup Circuit
%
µSec
%
300
5.0
0.02
25% Load Step Change
3.0
%/ºC
Continuous (Autorecovery)
Parameter
Conditions
Min.
60 Seconds 4,200
300 Vrms
Typ.
Max.
Units
Vrms
Isolation Voltage, Rated
Reinforced Insulation Working Voltage
Leakage Current
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
240 VAC, 60 Hz
500 VDC
5
µA
G⍀
pF
10
100 kHz, 1V
80
285
kHz
Conditions
Min.
Typ.
Max.
Units
Operating Temperature Range
Cooling
See Table on Page 3
Free Air Convection
Humidity
Altitude
RH, Non-condensing
95
4,000
%
m
Physical
Case Size
See Mechanical Diagram (Page 4)
Case Material
Weight
Reliability Specifications
Parameter
Non-Conductive Black Plastic (UL94-V0)
1.06 Oz (30g)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign 1.08
IEC/EN 60601-1, EN 60601-1 3RD Edition, 2xMOPP
Min.
Typ.
Max.
Units
MHours
MTBF
Safety Standards
ANSI/AAMI ES 60601-1 2xMOPP Recognition, (UL Certificate)
ANSI/AAMI ES 60601-1, CAN/CSA-C22.2 No.60601-1
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter
Conditions
12 VDC Input
Min.
Typ.
Max.
25.0
50.0
100.0
260
Units
VDC
ºC
Input Voltage Surge (0.1 Sec)
24 VDC Input
48 VDC Input
Lead Temperature
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Model Selection Guide
www.micropowerdirect.com
Input
Output
Reflected
Ripple
Capacitive Fuse Rating
Efficiency
Model
Voltage (VDC)
Current (mA)
Load
Slow-Blow
(mA)
Voltage Current
Current
Number
Current
(mA, Typ)
(%, Typ)
(µF Max)
(VDC)
(mA, Max) (mA, Min)
Nominal Range Full-Load No-Load
MB2012SMRW-05RI4
MB2012SMRW-12RI4
MB2012SMRW-15RI4
MB2012SMRW-24RI4
MB2012DMRW-12RI4
MB2012DMRW-15RI4
MB2024SMRW-05RI4
MB2024SMRW-12RI4
MB2024SMRW-15RI4
MB2024SMRW-24RI4
MB2024DMRW-12RI4
MB2024DMRW-15RI4
MB2048SMRW-05RI4
MB2048SMRW-12RI4
MB2048SMRW-15RI4
MB2048SMRW-24RI4
MB2048DMRW-12RI4
12
12
12
12
12
12
24
24
24
24
24
24
48
48
48
48
48
48
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
1,938
1,876
1,893
1,888
1,888
1,882
947
20
20
20
20
20
20
15
15
15
15
15
15
10
10
10
10
10
10
100
100
100
100
100
100
50
5.0
12.0
15.0
24.0
12.0
15.0
5.0
4,000
1,670
1,333
840
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
86
89
88
89
89
89
88
89
89
90
90
90
88
89
90
89
89
90
6,800
1,160
750
4,000
4,000
4,000
4,000
4,000
4,000
2,000
2,000
2,000
2,000
2,000
2,000
1,000
1,000
1,000
1,000
1,000
1,000
295
840
590
670
380
4,000
1,670
1,333
840
6,800
1,160
750
938
50
12.0
15.0
24.0
12.0
15.0
5.0
936
50
933
50
295
933
50
840
590
931
50
670
380
473
30
4,000
1,670
1,333
840
6,800
1,160
750
469
30
12.0
15.0
24.0
12.0
15.0
463
30
472
30
295
472
30
840
590
MB2048DMRW-15RI4
465
30
670
380
Notes:
1. The specified maximum capacitive load is for each output.
5. The converter should be connected to a low ac-impedance source. An input source with a
highly inductive impedance may affect the stability of the converter. In applications where
the converter output loading is high and input power is supplied over long lines, it may be
necessary to use a capacitor on the input to insure start-up. In this case, it is recommended
that a low ESR (ESR <1.0⍀ at 100 kHz) capacitor be mounted close to the converter. For 12V
input units a 10.0 µF is recommended, for 24V a 4.7 µF and for 48V units a 2.2 µF.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the
table above for the correct rating.
2. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor
be placed from the +VOUT pin to the -VOUT pin for single output units and from each output to
common for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors
will reduce the output ripple. The factory tests output ripple on these units with a MLCC 4.7 µF
capacitor connected.
3. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.
4. Dual output units may be connected to provide a 24 VDC or 30 VDC output.To do this, connect
the load across the positive (+VOUT) and negative (-VOUT) outputs and float the output common.
Typical Connection
EMI Characteristics
Parameter
These converters are specified for operation without external components.
However, in some applications the addition of input/output capacitors, as shown
in the typical connection diagram above, will enhance stability and reduce output
ripple.This simple connection includes a low ESR (<1ม at 100 kHz) capacitor
connected across the input (C1). It is recommended that a 10 µF be used
for 12V input models, a 4.7 µF for 24V and a 2.2 µF for 48V input units.
To improve the output ripple performance, a 4.7 µF is connected across
the output. For dual output units, a 4.7 µF capacitor should be connected from
each output to common.
Standard
EN 55011
Criteria
Level
Class A
Class A
15 kV Air
8 kV Contact
10V/m
Conducted Emissions
Radiated Emissions
EN 55011
ESD
EN 61000-4-2
A
RS
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
A
A
A
A
A
EFT, See Note at right
2 kV
To meet the specified EN 61000-4-4 and EN 61000-4-5 limits, an external
capacitor must be connected across the input pins of the module (C1). A
330 µF/100V capacitor is recommended. This capacitor should be mounted as
close to the module as possible.
Surge, See Note at right
1 kV
CS
10 Vrms
30A/m
PFMF
Page 2
We Power Your Success - For Less
Operating Temperature Range
www.micropowerdirect.com
Parameter
Model Number
Min Typ Max Units
Parameter
Model Number
Min Typ Max Units
MB2024SMRW-24RI4
MB2024DMRW-12RI4
MB2012SMRW-12RI4
MB2012SMRW-24RI4
MB2012DMRW-12RI4
MB2012DMRW-15RI4
Operating Temp Range MB2024DMRW-15RI4 -40 +25 +66
MB2048SMRW-15RI4
°C
MB2048SMRW-15RI4
Operating Temp Range MB2024SMRW-12RI4 -40 +25 +62
MB2024SMRW-15RI4
°C
MB2012SMRW-15RI4
Operating Temp Range MB2024DMRW-05RI4 -40 +25 +58
MB2048SMRW-05RI4
°C
°C
MB2048SMRW-12RI4
MB2048SMRW-24RI4
Operating Temp Range MB2012MS-05RWHI -40 +25 +51
MB2048DMRW-12RI4
Temperature Derating Curves
MB2024SMRW-24RI4, MB2024DMRW-12RI4
MB2048SMRW-15RI4, MB2048DMRW-15RI4
MB2012SMRW-15RI4, MB2024SMRW-05RI4
MB2048SM-05RI4
MB2012SMRW-12RI4, MB2012SMRW-24RI4
MB2012DMRW-12RI4, MB2012DMRW-15RI4
MB2024SMRW-12RI4, MB2024SMRW-15RI4
MB2048SMRW-12RI4, MB2048SMRW-24RI4
MB2048DMRW-12RI4
MB2012SMRW-05RI4
MPD
• 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
Mechanical Dimensions
www.micropowerdirect.com
Pin Connections
Pin Single
Dual
+VIN
Pin Single
Dual
Comm.
-VOUT
1
2
3
+VIN
-VIN
+VOUT
4
No Pin
-VIN
+VOUT
5
-VOUT
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
Related Products
Medical Approved DC/DC’s
MA600MRWRI5 Series
• 6W Output Power
• 5 kVrms Isolation
ML200MRRI4 Series
• 2W Output Power
MB1000MRWRI4 Series
• 10W Output Power
• 4 kVrms Isolation
• 4.2 kVrms Isolation
• Reinforced Insulation
•Meets 1xMOPP & 2xMOOP
• 10 µA Leakage Current Max
• Wide 2:1 Input Range
• Compact 1 x 2 In Case
• Single & Dual Outputs
• 1.0 MH MTBF
• Reinforced Insulation
• Meets 2xMOPP
• Reinforced Insulation
•Meets 1xMOPP & 2xMOOP
• 2 µA Leakage Current Max
• Compact SMT Case
• Available on Tape/Reel
• 2.0 MH MTBF
• 2 µA Leakage Current Max
• Wide 2:1 Input Range
• Compact DIP Case
• Single & Dual Outputs
• 1.0 MH MTBF
• EN 60601 Approved
• EN 60601 Approved
• EN 60601 Approved
Thousands of standard power products ranging from 0.5W to 500W are
available from MPD in a wide variety of packages and pin-outs. This
includes many more families with EN 60601 medical approval
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明