MD112MS12HI [MPD]

MD100MHI SERIES;


型号：	MD112MS12HI
厂家：	MICROPOWER DIRECT, LLC
描述：	MD100MHI SERIES
文件：	总2页 (文件大小：287K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Series

MD100MHI

Miniature, 1W SIP

Medical Approved

DC/DC Converters

Electrical Speciﬁcations

Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice.

Input

Parameter

Key Features:

• 1W Output Power

Conditions

Min.

Typ.

5.0

Max.

5.5

Units

5 VDC Input

4.5

Input Voltage Range

VDC

• 3 kVAC rms Isolation

12 VDC Input 10.8

LC Filter

12.0

13.2

Input Filter

• Reinforced Insulation

• Miniature SIP Case

• Single & Dual Outputs

• 12 Standard Models

• 2.0 MH MTBF

• Industry Standard Pin-Out

• EN 60950 Approved

• EN 60601 Approved

Reverse Polarity Input Current

0.3

Output

Parameter

Conditions

Min.

Typ.

1.0

0.1

1.2

Max.

3.0

Units

Output Voltage Accuracy

Output Voltage Balance

Line Regulation

Dual Output , Balanced Loads

For Vin Change of 1%

1.0

1.5

Load Regulation, See Note 1

Ripple & Noise (20 MHz), See Note 2

Ripple & Noise (20 MHz)

Temperature Coefﬁcient

Output Short Circuit

General

See Model Selection Guide

100

0.01

Typ.

150

200

mV P - P

mV rms

%/°C

Over Line, Load & Temp.

0.02

Momentary (0.5 Sec.)

Parameter

Conditions

Min.

Max.

Units

VAC rms

VPk

Isolation Voltage

60 Seconds 3,000

Isolation Test Voltage

Isolation Resistance

Isolation Capacitance

Switching Frequency

Environmental

Parameter

Flash Tested for 1 Sec 4,500

500 VDC

G

100 kHz, 1V

100

kHz

Conditions

Min.

Typ.

Max.

+85

Units

°C

Operating Temperature Range

Storage Temperature Range

Cooling

Ambient -25

Case

+90

°C

-50

+125

°C

Free Air Convection

Humidity

RH, Non-condensing

Physical

Case Size

0.87 x 0.30 x 0.49 Inches (22.0 x 7.5 x 12.5 mm)

Non-Conductive Black Plastic (UL94-V0)

0.13 Oz (3.9g)

Case Material

MicroPower Direct

292 Page Street

Suite D

Stoughton, MA 02072

USA

Weight

Reliability Speciﬁcations

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25°C, Gnd Benign

2.0

MHours

Safety Approvals

Absolute Maximum Ratings

Parameter

UL 60601, UL 60950, EN 60601, EN 60950

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

Conditions

Min.

5 VDC Input -0.7

12 VDC Input -0.7

Typ.

Max.

9.0

Units

Input Voltage Surge (1 Sec)

VDC

29.0

260

650

Lead Temperature

1.5 mm From Case For 10 Sec

All Models

°C

Internal Power Dissipation

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

www.micropowerdirect.com

Model Selection Guide

www.micropowerdirect.com

Input

Output

Load

Fuse Rating

Slow-Blow

(mA)

Model

Number

Efﬁciency

(%, Typ)

Voltage (VDC)

Current (mA)

Regulation

(%, Max)

Voltage Current

Current

(mA, Min)

(VDC)

(mA, Max)

Nominal Range

Full-Load No-Load

MD105MS-05HI

MD105MS-12HI

MD105MS-15HI

MD105MD-05HI

MD105MD-12HI

MD105MD-15HI

MD112MS-05HI

MD112MS-12HI

MD112MS-15HI

MD112MD-05HI

MD112MD-12HI

MD112MD-15HI

Notes:

4.5 - 5.5

303

291

295

303

267

287

126

121

123

126

108

117

5.0

12.0

15.0

5.0

200.0

80.0

65.0

100.0

40.0

35.0

200.0

80.0

65.0

100.0

40.0

35.0

4.0

2.0

1.0

2.0

1.0

4.0

2.0

1.0

2.0

1.0

500

200

4.5 - 5.5

12.0

15.0

5.0

4.5 - 5.5

10.8 - 13.2

12.0

15.0

5.0

12.0

15.0

Derating Curve

0. Output load regulation is speciﬁed for a load change of 2±% to 0±±%.

2. When measuring output ripple, it is recomended that an external ±.33 µF

ceramic capacitor be placed from the +Vout pin to the -Vout pin for single

output units and from each output to common for dual output units.

3. Operation at no-load will not damage these units. However, they may not meet

all speciﬁcations.

4. Dual output units may be connected to provide a 0± VDC, 24 VDC or 3± VDC

output. To do this, connect the load across the positive (+Vout) and negative

(-Vout) outputs and ﬂoat the output common.

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the table above for the correct rating.

Mechanical Dimensions

Pin Connections

Single

Dual

+Vin

-Vin

-Vout

No Pin

+Vout

-Vout

Common

+Vout

NC: No Connection

Capacitive Load

Single Output

Dual Output

µF Max

680

220

Mechanical Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = ±±.±0 (±±.25)

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

相关型号：